powRgrip System - Productivity Inc€™s powRgrip System is a unique collet-holding system ... TC...
Transcript of powRgrip System - Productivity Inc€™s powRgrip System is a unique collet-holding system ... TC...
powRgrip System
1 powRgrip Toolholders - Features | Benefits2 Features | Benefits3 Information4 CAT | PG Toolholders5 TC | PG Toolholders6 BT | PG Toolholders7 CYL | PG Toolholders8 HSK | PG Toolholders10 REGO-FIX CAPTO | PG Toolholders11 VDI | PG - CYL | PG Toolholders12 Swiss Quick Tool Changing System13 CYL SSY | PG Toolholders (Softsyncro)14 XL Toolholder - Vibration Decay Chart15 CAT/PG | XL (Xtended Length Toolholders)16 BT/PG | XL (Xtended Length Toolholders)17 TC/PG | XL (Xtended Length Toolholders)18 HSK/PG | XL (Xtended Length Toolholders)19 REGO-FIX CAPTO | PG XL Toolholders20 powRgrip Collets - What are PG Collets21 PG 6 - PG 1022 PG 15 - PG 25 - PG 3223 PG Boring Bar Collets24 secuRgrip | PG25 CAT | BT secuRgrip | PG26 HSK-A | HSK-E&F secuRgrip | PG27 REGO-FIX CAPTO secuRgrip | PG28 secuRgrip | PG Collets & Accessories29 PG Machine Options - PGU 9006 | PGC 2506
powRgrip System
30 Matching Products31 Maximum & Minimum Tool Depth32 Weldon Flats & h6 Shank tolerances
PG
1COL1116.1 09/2013
Home
More Technical Information available at WWW.REGO-FIX.COM
powRgrip® What is powRgrip?
Swiss QualityMade in Switzerland to ISO 9001/ISO 14001.
What is powRgrip REGO-FIX’s powRgrip System is a unique collet-holding system that utilizes a special shallow-tapered collet that is pressed into a holder with a matching taper. This state-of-the-art system uses either a hydraulic hand-pump or a table top hydraulic press specifically designed to quickly insert these collets with up to 9 tons of force.
T.I.R. of the Whole System < 0.0001" (3 μm)Highest clamping force and lowest runout.
Taper Accuracy AT3Better spindle-to-holder fit and accuracy.
Surface Finish max. Ra 0.25Higher clamping force and higher transferable torque.
Q+® Balancing 100% balanced to lowest possible residual imbalance.
• Steep Taper balanced to G2.5 @ 22,000 rpm• BT 30 Taper balanced to 30,000 rpm• HSK 25 balanced to 90,000 rpm• HSK 32 balanced to 60,000 rpm• HSK 40 balanced to 45,000 rpm• HSK 50 balanced to 30,000 rpm• HSK 63 G2.5 @ 25,000 rpm• HSK 80 G2.5 @ 25,000 rpm• HSK 100 G2.5 @ 25,000 rpm• HSK 125 G2.5 @ 25,000 rpm
Hi-Q® Balancing System Ready to accept Hi-Q® balancing rings which will allow for the offset of the imbalance introduced by the cutting tool up to 80,000 rpm.
Minimal Outside DimensionsSlim design provides more processing flexibility.
FastTool clamping with hydraulic press < 10 seconds.
Excellent at Small DiametersClamping of small diameter tools from Ø 0.2 mm.
Presetable Tooling SystemRepeatability < 0.0004" (10 μm)
PG
2COL1116.1 09/2013
Home
More Technical Information available at WWW.REGO-FIX.COM
powRgrip® Features Benefits
T.I.R. of < 0.0001" (3 μm)
Clamping operation in less than 10 seconds when using the PGU automatic machine.
High vibration dampening due to the interupted surfaces between the toolholder to collet and the collet to tool shank.
Highest transferable torque and lowest T.I.R., even after 20,000 tool changes
For 5 years or 20,000 cycles, REGO-FIX® guarantees the T.I.R. of a properly maintained powRgrip® holder and collet will not exceed 0.0001” and that the impregnated surface treatment will not erode.
Precise length adjustmentrepeatability <0.0004" (10 μm)
Clamps all types of toolshanks and materials in h6 tolerance from Ø 0.0079" – 1.0" (0.2 – 25.4 mm)
Developed for optimal productivity such as High Speed Cutting (HSC) and High Performance Cutting (HPC)
Transferable Torque of the powRgrip® System
PG
3COL1116.1 09/2013
Home
More Technical Information available at WWW.REGO-FIX.COM
Information
PG ToolholdersApplicationsThese toolholders are designed for use on CNC machining centers with automatic tool changers. They are especially suited for High Speed Cutting (HSC) and High Performance Cutting (HPC) operations where processing reaches the machine limits. The vibration dampening of PG colletholders reduce spindle wear and extend tool life.
BalancingREGO-FIX® Q+® System PG toolholders are balanced by design to G 2.5 @ 22,000 rpm for steep taper holders and up to 90,000 rpm for HSK holders. Type H toolholders are ready to accept Hi-Q® balancing rings which allow precision balancing of the system up to 80,000 rpm depending on the balancing rings used.
Coolant ThroughFor use with coolant through tools.
Peripheral CoolingPG-CF collets for peripheral cooling with non-coolant through tools.
Matched Tooling System for Best FitFor highest precision and best results the whole system counts. For that reason REGO-FIX® components are carefully matched to fit together. This guarantees best run-out and balancing.
Tool Precise preset repeatability
for both HSS and carbide tools
ColletSlightly tapered shape
maximizes clamping force
HolderSuperior runout and
vibration dampening in a variety of taper styles
As a Licensed BIG Plus manufacturer, REGO-FIX® uses new state of the art measuring and grinding systems to create the most accurate dual contact holders that can be produced.
Taper Contact
Flange Contact
PG
4COL1116.1 09/2013
Home
More Technical Information available at WWW.REGO-FIX.COM
Standard
CAT Toolholders
TypeStandardPart No.
Form BPart No.
D[mm]
L[inch]
Balancing Rings
CAT 40 / PG 6 x 3” H 4340.70631 – 10 3 FWR 285
CAT 40 / PG 10 x 3.5" H 4340.71001 4340.71004 16 3.5 FWR 285
CAT 40 / PG 10 x 6" H 4340.71071 4340.71074 16 6 FWR 285
CAT 40 / PG 15 x 3.15" H 4340.71541 4340.71544 24 3 FWR 285
CAT 40 / PG 15 x 4" H 4340.71551 4340.71554 24 4 FWR 285
CAT 40 / PG 15 x 6" H 4340.71571 4340.71574 24 6 FWR 325/285
CAT 40 / PG 25 x 3.15" H 4340.72541 4340.72544 40 3 FWR 405
CAT 40 / PG 25 x 4" H 4340.72551 4340.72554 40 4 FWR 405
CAT 40 / PG 25 x 6" H 4340.72571 4340.72574 40 6 FWR 405/405
CAT 40 / PG 32 x 3.5” H* 2340.73201 – 50 3.5 –
CAT 40 / PG 32 x 4.3" H 4340.73251 4340.73254 50 4.3 FWR 505
CAT 40 / PG 32 x 6" H 4340.73271 4340.73274 50 6 FWR 505/505
CAT 50 / PG 10 x 4” H 4350.71051 – 16 4 FWR 405
CAT 50 / PG 15 x 4” H 4350.71551 – 24 4 FWR 405
CAT 50 / PG 25 x 4" H 4350.72551 4350.72554 40 4.0 FWR 505
CAT 50 / PG 25 x 6" H 4350.72571 4350.72574 40 6.0 FWR 505/405
CAT 50 / PG 32 x 4.3" H 4350.73251 4350.73254 50 4.3 FWR 505
CAT 50 / PG 32 x 6" H 4350.73271 4350.73274 50 6 FWR 505/505
*Not for use with balancing rings.
CAT CAT+ PG
Form B
TypeStandardPart No.
D[mm]
L[inch]
Balancing Rings
CAT+ 40 / PG 10 x 3.5" H 4340.71006 16 3.5 FWR 285
CAT+ 40 / PG 10 x 6" H 4340.71076 16 6 FWR 285
CAT+ 40 / PG 15 x 3.15" H 4340.71546 24 3 FWR 285
CAT+ 40 / PG 15 x 6" H 4340.71576 24 6 FWR 325/285
CAT+ 40 / PG 25 x 3.15" H 4340.72546 40 3 FWR 405
CAT+ 40 / PG 25 x 6" H 4340.72576 40 6 FWR 405/405
CAT+ 40 / PG 32 x 3.5” 2340.73206 50 3.5 –
CAT+ 40 / PG 32 x 6” 4340.73276 50 6 FWR 505/405
CAT+ 50 / PG 10 x 4” H 4350.71056 16 4 FWR 405
CAT+ 50 / PG 15 x 4” H 4350.71556 24 4 FWR 405
CAT+ 50 / PG 25 x 4” H 4350.72556 40 4 FWR 505
CAT+ 50 / PG 25 x 6” H 4350.72576 40 6 FWR 505/405
CAT+ 50 / PG 32 x 4.3” H 4350.73256 50 4.3 FWR 505
CAT+ 50 / PG 32 x 6” H 4350.73276 50 6 FWR 505/505
“BIG-PLUS SYSTEM - Licensed by BIG Daishowa”
CAT+ 40 Toolholders
PG
5COL1116.1 09/2013
Home
More Technical Information available at WWW.REGO-FIX.COM
Standard
TC Toolholders (DIN 69871)
TypeStandardPart No.
Form BPart No.
D[mm]
L[mm]
Balancing Rings
TC 30 / PG 10 x 060* 2230.71020 – 16 60 –
TC 30 / PG 10 x 073 H 4230.71030 – 16 73 FWR 285
TC 30 / PG 15 x 060* 2230.71520 – 24 60 –
TC 30 / PG 15 x 080 H 4230.71540 – 24 80 FWR 285
TC 30 / PG 15 x 120 H 4230.71560 – 24 120 FWR 285
TC 30 / PG 25 x 080* 2230.72540 – 40 80 –
TC 30 / PG 25 x 160 H 4230.72580 – 40 160 FWR 405
TC 40 / PG 10 x 080 H 4240.71040 4240.71043 16 80 FWR 285
TC 40 / PG 10 x 120 H 4240.71060 4240.71063 16 120 FWR 285
TC 40 / PG 10 x 160 H 4240.71080 4240.71083 16 160 FWR 325
TC 40 / PG 15 x 072* 2240.71530 2240.71533 24 72 –
TC 40 / PG 15 x 080 H 4240.71540 4240.71543 24 80 FWR 285
TC 40 / PG 15 x 120 H 4240.71560 4240.71563 24 120 FWR 325
TC 40 / PG 15 x 160 H 4240.71580 4240.71583 24 160 FWR 325/285
TC 40 / PG 25 x 072* 2240.72530 2240.72533 40 72 –
TC 40 / PG 25 x 080 H 4240.72540 4240.72543 40 80 FWR 405
TC 40 / PG 25 x 120 H 4240.72560 4240.72563 40 120 FWR 405
TC 40 / PG 25 x 160 H 4240.72580 4240.72583 40 160 FWR 405/405
TC 40 / PG 32 x 080* 2240.73240 2240.73243 50 80 –
TC 50 / PG 25 x 081* 2250.72540 2250.72543 40 81 –
TC 50 / PG 25 x 100 H 4250.72550 4250.72553 40 100 FWR 505
TC 50 / PG 25 x 160 H 4250.72580 4250.72583 40 160 FWR 505/405
TC 50 / PG 25 x 200 H 4250.72590 4250.72593 40 200 FWR 505/405
TC 50 / PG 32 x 080* 2250.73240 2250.73243 50 80 –
*Not for use with balancing rings.
Form B
TC PG
PG
6COL1116.1 09/2013
Home
More Technical Information available at WWW.REGO-FIX.COM
TypeStandardPart No.
Form BPart No.
D[mm]
L [mm]
Balancing Rings
BT 30 / PG 6 x 050 2130.70610 – 10 50 –
BT 30 / PG 6 x 100 H 4130.70650 – 10 100 –
BT 30 / PG 10 x 062* 2130.71020 – 16 62 –
BT 30 / PG 10 x 080 H 4130.71040 – 16 80 FWR 285
BT 30 / PG 10 x 120 H 4130.71060 – 16 120 FWR 285
BT 30 / PG 10 x 160 H 4130.71080 – 16 160 FWR 285
BT 30 / PG 15 x 070 H 4130.71530 – 24 70 FWR 285
BT 30 / PG 15 x 120 H 4130.71560 – 24 120 FWR 285
BT 30 / PG 25 x 080 H 4130.72540 – 40 80 FWR 405
BT 30 / PG 25 x 120 H 4130.72560 – 40 120 FWR 405
BT 30 / PG 25 x 160 H 4130.72580 – 40 160 FWR 405/405
BT 40 / PG 10 x 080 H 4140.71040 4140.71043 16 80 FWR 285
BT 40 / PG 10 x 120 H 4140.71060 4140.71063 16 120 FWR 325
BT 40 / PG 10 x 160 H 4140.71080 4140.71083 16 160 FWR 325
BT 40 / PG 15 x 080 H 4140.71540 4140.71543 24 80 FWR 285
BT 40 / PG 15 x 120 H 4140.71560 4140.71563 24 120 FWR 325
BT 40 / PG 15 x 160 H 4140.71580 4140.71583 24 160 FWR 325/285
BT 40 / PG 25 x 080 H 4140.72540 4140.72543 40 80 FWR 405
BT 40 / PG 25 x 120 H 4140.72560 4140.72563 40 120 FWR 405
BT 40 / PG 25 x 160 H 4140.72580 4140.72583 40 160 FWR 405/405
BT 40 / PG 32 x 086* 2140.73240 2140.73243 50 86 –
BT 50 / PG 10 x 120 H 4150.71060 – 16 120 FWR 405
BT 50 / PG 10 x 160 H 4150.71080 – 16 160 FWR 405
BT 50 / PG 15 x 120 H 4150.71560 – 24 120 FWR 325
BT 50 / PG 15 x 160 H 4150.71580 – 24 160 FWR 325
BT 50 / PG 25 x 100* 2150.72550 – 40 100 –
BT 50 / PG 25 x 120 H 4150.72560 – 40 120 FWR 505
BT 50 / PG 25 x 160 H 4150.72580 – 40 160 FWR 505/405
BT 50 / PG 25 x 200 H 4150.72590 – 40 200 FWR 505/405
BT 50 / PG 32 x 100* 2150.73250 – 50 100 –
* Not for use with balancing rings
BT Toolholders
Standard
Form B
BT BT+ PG
TypeStandardPart No.
D [mm]
L [mm]
Balancing Rings
BT+ 30 / PG 10 x 080 H 4130.71046 16 80 FWR 285
BT+ 30 / PG 15 x 070 H 4130.71536 24 70 FWR 285
BT+ 30 / PG 25 x 080 H 4130.72546 40 80 FWR 405
BT +30 / PG 25 x 160H 4130.72586 40 160 FWR 405/405
BT+ 40 / PG 10 x 080 H 4140.71046 16 80 FWR 285
BT+ 40 / PG 10 x 120 H 4140.71066 16 120 FWR 325
BT+ 40 / PG 15 x 080 H 4140.71546 24 80 FWR 285
BT +40 / PG 15 x 120H 4140.71566 24 120 FWR 325
BT+ 40 / PG 25 x 080 H 4140.72546 40 80 FWR 405
BT+ 40 / PG 25 x 120 H 4140.72566 40 120 FWR 405
BT+ 40 / PG 25 x 160 H 4140.72586 40 160 FWR 405/405
BT+ 50 / PG 25 x 120 H 4150.72566 40 120 FWR 505
BT+ 50 / PG 25 x 160 H 4150.72586 40 160 FWR 505/405
“BIG-PLUS SYSTEM - Licensed by BIG Daishowa”
BT+ Toolholders
PG
7COL1116.1 09/2013
Home
More Technical Information available at WWW.REGO-FIX.COM
1
2
Form B
Extensions
Type Part No.D
[mm]D1 h6[mm]
L[mm]
L1[mm] Drawing
CYL 10 / PG 6 x 120 2610.70620 10 10 35 124 1
CYL 10 / PG 10 x 120 2610.71020 16 10 120 40 2
CYL 20 / PG 10 x 120 2620.71020 16 20 120 50 1
CYL 20 / PG 10 x 160 2620.71040 16 20 160 50 1
CYL 20 / PG 10 x 200 2620.71060 16 20 200 50 1
CYL 20 / PG 15 x 120 2620.71520 24 20 120 50 2
CYL 25 / PG 15 x 045 2625.71522 24 25 50 60 2
CYL 1“ / PG 25 x 045 2625.71523 24 1“ 50 60 2
CYL 25 / PG 25 x 80 8020.25080 40 25 80 50 2
CYL 25 / PG 25 X 100 8020.25100 40 25 100 50 2
CYL 25 / PG 25 X 120 8020.25120 40 25 120 50 2
PG Toolholders Type OM
TypeStandardPart No.
D [mm]
L[mm] Balancing Rings
BT-OM 30 / PG 10 x 062 H 2130.71028 16 62 –
BT-OM 30 / PG 15 x 070 H 4130.71538 24 70 FWR 285
BT-OM 30 / PG 25 x 080 H 4130.72548 40 80 FWR 405
OM Type holders have no drive keys
CYL PG
BT OM PG
PG
8COL1116.1 09/2013
Home
More Technical Information available at WWW.REGO-FIX.COM
HSK - Form A Holders
Type Part No.D
[mm]L
[mm]Balancing
Rings
HSK-A 32 / PG 10 x 060* 2532.71020 16 60 –
HSK-A 32 / PG 15 x 075* 2532.71530 24 75 –
HSK-A 40 / PG 6 x 048* 2540.70610 10 48 –
HSK-A 40 / PG 6 x 080 H 4540.70640 10 80 FWR 225
HSK-A 40 / PG 10 x 062* 2540.71020 16 62 –
HSK-A 40 / PG 15 x 080 H 4540.71540 24 80 FWR 285
HSK-A 40 / PG 25 x 100 H 4540.72550 40 100 FWR 405
HSK-A 50 / PG 10 x 080 H 4550.71040 16 80 FWR 285
HSK-A 50 / PG 15 x 080 H 4550.71540 24 80 FWR 285
HSK-A 50 / PG 25 x 100 H 4550.72550 40 100 FWR 405
HSK-A 63 / PG 6 x 080 H 4563.70640 10 80 FWR 325
HSK-A 63 / PG 10 x 080 H 4563.71040 16 80 FWR 325
HSK-A 63 / PG 10 x 120 H 4563.71060 16 120 FWR 325
HSK-A 63 / PG 10 x 160 H 4563.71080 16 160 FWR 325
HSK-A 63 / PG 10 x 200 H 4563.71090 16 200 FWR 325
HSK-A 63 / PG 15 x 080 H 4563.71540 24 80 FWR 325
HSK-A 63 / PG 15 x 120 H 4563.71560 24 120 FWR 325
HSK-A 63 / PG 15 x 160 H 4563.71580 24 160 FWR 325/285
HSK-A 63 / PG 25 x 100 H 4563.72550 40 100 FWR 405
HSK-A 63 / PG 25 x 120 H 4563.72560 40 120 FWR 405
HSK-A 63 / PG 25 x 160 H 4563.72580 40 160 FWR 405/405
HSK-A 63 / PG 25 x 200 H 4563.72590 40 200 FWR 405/405
HSK-A 63 / PG 32 x 100* 2563.73250 50 100 –
HSK-A 63 / PG 32 x 120 H 4563.73260 50 120 FWR 505
HSK-A 80 / PG 15 x 085 H 4580.71540 24 85 FWR 325
HSK-A 80 / PG 25 x 100 H 4580.72550 40 100 FWR 505
HSK-A 80 / PG 32 x 105 H 4580.73250 50 105 FWR 505
HSK-A 100 / PG 10 x 085 H 4500.71040 16 85 FWR 405
HSK-A 100 / PG 10 x 160 H 4500.71080 16 160 FWR 405
HSK-A 100 / PG 15 x 085 H 4500.71540 24 85 FWR 405
Type Part No.D
[mm]L
[mm]Balancing
Rings
HSK-A 100 / PG 15 x 160 H 4500.71580 24 160 FWR 405/285
HSK-A 100 / PG 25 x 100 H 4500.72550 40 100 FWR 505
HSK-A 100 / PG 25 x 160 H 4500.72580 40 160 FWR 505/405
HSK-A 100 / PG 25 x 200 H 4500.72590 40 200 FWR 505/405
HSK-A 100 / PG 32 x 106 H 4500.73250 50 106 FWR 505
HSK-E 25 / PG 6 x 043* 2525.70614 10 43 –
HSK-E 25 / PG 10 x 055* 2525.71014 16 55 –
HSK-E 32 / PG 6 x 048* 2532.70614 10 48 –
HSK-E 32 / PG 10 x 060* 2532.71024 16 60 –
HSK-E 32 / PG 10 x 080 H 4532.71044 16 80 FWR 225
HSK-E 32 / PG 15 x 075* 2532.71534 24 75 –
HSK-E 40 WM / PG 6 x 048*+ 2540.70617 10 48 –
HSK-E 40 WM / PG 10 x 052*+ 2540.71017 16 52 –
HSK-E 40 WM / PG 10 x 062*+ 2540.71027 16 62 –
HSK-E 40 / PG 6 x 048* 2540.70614 10 48 –
HSK-E 40 / PG 6 x 080 4540.70644 10 80 FWR 225
HSK-E 40 / PG 10 x 062* 4540.70644 16 62 –
HSK-E 40 / PG 10 x 080 H 4540.71044 16 80 FWR 225
HSK-E 40 WM / PG 10 x 080 H+ 4540.71047 16 80 FWR225
HSK-E 40 / PG 10 x 120 H 4540.71064 16 120 FWR 225
HSK-E 40 / PG 10 x 160 H 4540.71084 16 160 FWR 285
HSK-E 40 WM / PG 15 x 064*+ 2540.71527 24 64 –
HSK-E 40 / PG 15 x 080 H 4540.71544 24 80 FWR 285
HSK-E 40 WM / PG 15 x 080 H+ 4540.71547 24 80 FWR 285
HSK-E 40 / PG 15 x 120 H 4540.71564 24 120 FWR 285
HSK-E 40 / PG 25 x 090* 2540.72544 40 90 –
HSK-E 40 / PG 25 x 100 H 4540.72554 40 100 FWR 405
HSK-E 50 / PG 6 x 080 H 4550.70644 10 80 FWR 285
HSK-E 50 / PG 10 x 080 H 4550.71044 16 80 FWR 285
HSK-E 50 / PG 10 x 120 H 4550.71064 16 120 FWR 285
HSK - Form A & E Holders Continued
HSK PG
* Not for use with balancing rings. * Not for use with balancing rings. +Compatible with Willemin-Macodel Machines
PG
9COL1116.1 09/2013
Home
More Technical Information available at WWW.REGO-FIX.COM
HSK PG
HSK - Form E Holders Continued
Type Part No.D
[mm]L
[mm]Balancing
Rings
HSK-E 50 / PG 10 x 160 H 4550.71084 16 160 FWR 285
HSK-E 50 / PG 15 x 080 H 4550.71544 24 80 FWR 285
HSK-E 50 / PG 15 x 120 H 4550.71564 24 120 FWR 285
HSK-E 50 / PG 25 x 100 H 4550.72554 40 100 FWR 405
HSK-F 63 / PG 10 x 080 H 4563.71045 16 80 FWR 325
HSK-F 63 / PG 10 x 120 4563.71065 16 120 FWR 285
HSK-F 63 / PG 10 x 160 4563.71085 16 160 FWR 285
HSK-F 63 / PG 15 x 080 H 4563.71545 24 80 FWR 325
HSK-F 63 / PG 15 x 120 H 4563.71565 24 120 FWR 325
HSK-F 63 / PG 15 x 160 H 4563.71585 24 160 FWR 325
HSK-F 63 / PG 25 x 100 H 4563.72555 40 100 FWR 405
HSK-F 63 / PG 25 x 160 H 4563.72585 40 160 FWR 405/405
HSK-F 63 / PG 32 x 100* 2563.73255 50 100 –
HSK-F 80 Call For Availability 800-999-7346
* Not for use with balancing rings.
PG
10COL1116.1 09/2013
Home
More Technical Information available at WWW.REGO-FIX.COM
Type Part No.D
[mm]L
[mm]Balancing
Rings
C3 / PG 6 x 045* 2803.70610 10 45 –
C3 / PG 10 x 055* 2803.71010 16 55 –
C3 / PG 15 x 067* 2803.71520 24 67 –
C4 / PG 6 x 048* 2804.70610 10 48 –
C4 / PG 10 x 060* 2804.71020 16 60 –
C4 / PG 10 x 080 H 4804.71040 16 80 FWR 225
C4 / PG 15 x 062* 2804.71520 24 62 –
C4 / PG 15 x 080 H 4804.71540 24 80 FWR 285
C5 / PG 6 x 080 H 4805.40640 10 80 FWR 285
C5 / PG 10 x 060* 2805.71020 16 60 –
C5 / PG 10 x 080 H 4805.71040 16 80 FWR 285
C5 / PG 10 x 120 H 4805.71060 16 120 FWR 285
C5 / PG 15 x 065* 2805.71520 24 65 –
C5 / PG 15 x 080 H 4805.71540 24 80 FWR 285
C5 / PG 15 x 120 H 4805.71560 24 120 FWR 325
C5 / PG 25 x 080* 2805.72540 40 80 –
C5 / PG 25 x 100 H 4805.72550 40 100 FWR 405
REGO-FIX CAPTO Holders
REGO-FIX CAPTO PG
Type Part No.D
[mm]L
[mm]Balancing
Rings
C6 / PG 10 x 080 H 4806.71040 16 80 FWR 325
C6 / PG 10 x 120 H 4806.71060 16 120 FWR 325
C6 / PG 10 x 160 H 4806.71080 16 160 FWR 325
C6 / PG 15 x 080 H 4806.71540 24 80 FWR 325
C6 / PG 15 x 120 H 4806.71560 24 120 FWR 325
C6 / PG 15 x 160 H 4806.71580 24 160 FWR 325
C6 / PG 25 x 085* 2806.72540 40 85 –
C6 / PG 25 x 100 H 4806.72550 40 100 FWR 405
C6 / PG 25 x 120 H 4806.72560 40 120 FWR 405
C6 / PG 25 x 160 H 4806.72580 40 160 FWR 405
C6 / PG 32 x 090* 2806.73240 50 90 –
C8 / PG 25 x 092* 2808.72540 40 92 –
C8 / PG 32 x 090* 2808.73240 50 90 –
*Not for use with balancing rings.
PG
11COL1116.1 09/2013
Home
More Technical Information available at WWW.REGO-FIX.COM
VDI PG
The PG VDI holder program brings the benefits to lathes that until now, only milling machines have taken advantage of for years. These include better TIR, improved tool dampening, easier presetting, longer tool life and unparalleled clamping forces.
Type Part No.D
[mm]D1
[mm]L
[mm]L1
[mm]
VDI 30 / PG 15 x 077 2930.71530 24 30 77 55
VDI 30 / PG 25 x 082 2930.72540 40 30 82 60
VDI 40 / PG 15 x 077 2940.71530 24 40 77 55
VDI 40 / PG 25 x 082 2940.72540 40 40 82 60
VDI 50 / PG 15 x 085 2950.71540 24 50 85 55
VDI 50 / PG 25 x 090 2950.72540 40 50 90 60
The PG Cylindrical Turning holders have all of the features that you expect from the PG system, now available for machines that require cylindrical holders. Available in the most common mounting block and turret diameters, these holders will bring new precision and repeatability to any machine application.
Type Part No.D
[mm]D1
[mm]L
[mm]L1
[mm]
CYL-T 25 / PG 15 x 045 2625.71522 24 25 50 60
CYL-T 32 / PG 15 x 045 2632.71522 24 32 50 60
CYL-T 32 / PG 25 x 070 2632.72542 40 32 70 60
CYL-T 40 / PG 15 x 050 2640.71522 24 40 55 60
CYL-T 40 / PG 25 x 065 2640.72542 40 40 65 60
CYL-T 1“ / PG 15 x 045 2625.71523 24 1“ 50 60
CYL-T 1 1/4“ / PG 15 x 045 2631.71523 24 1 1/4“ 50 60
CYL-T 1 1/4“ / PG 25 x 070 2631.72543 40 1 1/4“ 70 60
CYL-T 1 1/2“ / PG 15 x 050 2638.71523 24 1 1/2“ 55 60
CYL-T 1 1/2“ / PG 25 x 065 2638.72543 40 1 1/2“ 65 60
Cylindrical PG
VDI Toolholders
Cylindrical Toolholders
PG
12COL1116.1 09/2013
Home
More Technical Information available at WWW.REGO-FIX.COM
Type Part No.L
[mm]D
[mm]Fine Thread Main Nut
ER 20 M / PG 10 7661.20100 35.5 16
ER 25 M / PG 15 7661.25150 36 24
Coarse Thread Main Nut
ER 20 / PG 10 7660.20100 35.5 16
ER 25 / PG 15 7660.25150 36 24PGU Automatic or PGC hand-pump is required
for use with the powRgrip System
What is Swiss Quick?
powRgrip / ER Reductions
Swiss Quick Tool Changing System
Swiss QualityMade in Switzerland to ISO 9001/ISO 14001.
What is Swiss Quick Tool Changing SystemOne of the latest REGO-FIX innovations is the SwissQuick ER to ER adapter. These are short “mini-holders” with a solid ER body profile on the back end, and a smaller ER series cavity on the front end. This unique design results in the shortest and most rigid ER to ER reduction available. Because of the solid body design, accuracy can be improved with a taper to collet cavity TIR of less than 0.0001” (3 um), and are repeatable within 0.0005” on tool length. Locking RingSpecial locking ring to insure that the collet body is removed with the nut.
Matched Tooling System for Best FitFor highest precision and best results the whole system counts. For that reason REGO-FIX® components are carefully matched for optimum fit and accuracy. This guarantees the best run-out and balance.
TIR of the SystemPG run-out of 0.0001” or better when using the REGO-FIX® powRgrip® System.
ER run-out of 0.0002” or better with a REGO-FIX® UP Collet
PG
13COL1116.1 09/2013
Home
More Technical Information available at WWW.REGO-FIX.COM
CYL SSY PG DIN 1835 B+E
PG Softsynchro®
Tapping HolderApplicationsREGO-FIX® Softsynchro® tapping holders are used on machines that are designed for direct tapping. Many of the newer CNC machines feature synchronization between spindle feed and thread pitch. This allows to use rigid tapping holders. However due to the dynamics of spindle and linear motors synchronization errors occur. To compensate for these synchronization errors Softsynchro® tapping holders with minimal length adjustment are necessary. Depending on the application Softsynchro® tapping holders increase tool life up to 150%.
Comparison TestsThe two diagrams show the axial forces when cold-forming M10 threads in St37 steel.
Conclusion: Axial forces increase with increasing rpm. With REGO-FIX® Softsynchro® tapping holders the forces are considerably lower than when using rigid tapping toolholders. Therefore the surface quality and tool life is optimized when using Softsynchro® tapping holders on a synchronized machine spindle.
CYL SSY/PG Softsynchro® Tapping Holders
Type Part No.D
[mm]D1
[mm]L
[mm]L1
[mm]Compression
[mm]Tension[mm]
CYL 25 SSY / PG 15 2625.61507 24 25 92 57 0.5 0.5
CYL 25 SSY / PG 25 2625.62507 40 25 109.5 57 0.5 0.5
HSK-A SSY/PG Softsynchro® Tapping Holders
Type Part No.D
[mm]L
[mm]Compression
[mm]Tension[mm]
HSK-A 63 SSY / PG 15 2563.61507 24 114.5 0.5 0.5
HSK-A 63 SSY / PG 25 2563.62507 40 131 0.5 0.5
3000
2500
2000
1500
1000
500
0
3000
2500
2000
1500
1000
500
0
Drehzahl 500 min -1
Axial
kraft [
N]
Zeit [s] 0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 5.5 6
Drehzahl 2000 min -1
Axial
kraft [
N]
Zeit [s] 0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 5.5 6
REGO- FIX® Softsynchro®-GewindeschneidfutterMitbewerber Synchron-WerkzeugaufnahmeStarre Synchron-Werkzeugaufnahme
3000
2500
2000
1500
1000
500
0
3000
2500
2000
1500
1000
500
0
Drehzahl 500 min -1
Axial
kraft [
N]
Zeit [s] 0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 5.5 6
Drehzahl 2000 min -1
Axial
kraft [
N]
Zeit [s] 0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 5.5 6
REGO- FIX® Softsynchro®-GewindeschneidfutterMitbewerber Synchron-WerkzeugaufnahmeStarre Synchron-Werkzeugaufnahme
r.p.m 500 min-1
Time Sec.Time Sec.
Axi
al F
orce
[N]
Axi
al F
orce
[N]
r.p.m 2000 min-1
PG
14COL1116.1 09/2013
Home
More Technical Information available at WWW.REGO-FIX.COM
Vibration Decay Chart
This New MICRO-FRICTION DAMPENING™ (MFD) technology (pat. pending) from REGO-FIX allows the holders to dissipate vibrations faster than standard long reach holders. Dampening the vibrations faster means that your cutting tool, part and spindle will see less vibrations resulting in better surface finishes, longer tool life and less spindle wear.
Machining parameters have to be adapted to the gauge length of the Xtended Length
Toolholders
0 100 200 300 400 500 600 700-1000
-500
0
500
1000
1500
Zeit in ms / Time in ms
Bes
chle
unig
ung
in m
/s2 /
Acc
eler
atio
n in
m/s
2
0 100 200 300 400 500 600 700-1000
-500
0
500
1000
1500
Zeit in ms / Time in ms
Bes
chle
unig
ung
in m
/s2 /
Acc
eler
atio
n in
m/s
2
0 100 200 300 400 500 600 700-1000
-500
0
500
1000
1500
Zeit in ms / Time in ms
Bes
chle
unig
ung
in m
/s2 /
Acc
eler
atio
n in
m/s
2
0 100 200 300 400 500 600 700-1000
-500
0
500
1000
1500
Zeit in ms / Time in ms
Bes
chle
unig
ung
in m
/s2 /
Acc
eler
atio
n in
m/s
2
Standard toolholder
REGO-FIX® Xtended Length Toolholder with MFD™ Technology.
Acce
lerati
on in
m/s
2
Time in ms
Acce
lerati
on in
m/s
2
Time in ms
REGO-FIX® XL Toolholder
PG
15COL1116.1 09/2013
Home
More Technical Information available at WWW.REGO-FIX.COM
+Holder is mono-block design and does not feature vibration dampening technology. Note: Maximum 5,000 r.p.m.
Type Part No.D1
[mm]D2
[mm]D3
[mm]L1
[mm]L2
[mm]L3
[inch]L
[inch]
CAT40 / PG 10 x 8 XL 8843.71031 16 28 42 31 84 4 8
CAT40 / PG 10 x10 XL 8843.71081 16 28 42 31 84 4 10
CAT40 / PG 10 x 12 XL 8843.71131 16 28 42 31 124 8 12
CAT40 / PG 10 x 14 XL 8843.71181 16 28 42 31 124 8 14
CAT40 / PG 15 x 8 XL 8843.73031 24 28 42 55 75 4 8
CAT40 / PG 15 x 10 XL 8843.73081 24 28 42 55 75 4 10
CAT40 / PG 15 x 12 XL 8843.73131 24 28 42 55 125 8 12
CAT40 / PG 15 x 14 XL 8843.73181 24 28 42 55 125 8 14
CAT40 / PG 25 x 8+ 4340.72591 40 – 52 – – – 8
CAT40 / PG 25 x10 XL 8843.76081 40 – 52 – – 4 10
CAT40 / PG 25 x14 XL 8843.76181 40 – 52 – – 8 14
CAT50 / PG 10 x 8 XL 8853.71031 16 28 42 31 84 4 8
CAT50 / PG 10 x 10 XL 8853.71081 16 28 42 31 84 4 10
CAT50 / PG 10 x 12 XL 8853.71131 16 28 42 31 124 8 12
CAT50 / PG 10 x 14 XL 8853.71181 16 28 42 31 124 8 14
CAT50 / PG 15 x 8 XL 8853.73031 24 28 42 55 75 4 8
CAT50 / PG 15 x 10 XL 8853.73081 24 28 42 55 75 4 10
CAT50 / PG 15 x 12 XL 8853.73131 24 28 42 55 125 8 12
CAT50 / PG 15 x 14 XL 8853.73181 24 28 42 55 125 8 14
CAT50 / PG 25 x10 XL 8853.76081 40 – 52 – – 4 10
CAT50 / PG 25 x14 XL 8853.76181 40 – 52 – – 8 14
CAT PG XLANSI B5.50
CAT XL Toolholders
PG
16COL1116.1 09/2013
Home
More Technical Information available at WWW.REGO-FIX.COM
Type Part No.D1
[mm]D2
[mm]D3
[mm]L1
[mm]L2
[mm]L3
[mm]L
[mm]
BT40 / PG 10 x 220 XL 8841.71050 16 28 42 31 84 140 220
BT40 / PG 10 x 260 XL 8841.71090 16 28 42 31 84 140 260
BT40 / PG 10 x 300 XL 8841.71130 16 28 42 31 84 140 300
BT40 / PG 10 x 320 XL 8841.71150 16 28 42 31 124 240 320
BT40 / PG 10 x 360 XL 8841.71190 16 28 42 31 124 240 360
BT40 / PG 10 x 400 XL 8841.71230 16 28 42 31 124 240 400
BT40 / PG 15 x 220 XL 8841.73050 24 28 42 55 75 140 220
BT40 / PG 15 x 260 XL 8841.73090 24 28 42 55 75 140 260
BT40 / PG 15 x 300 XL 8841.73130 24 28 42 55 75 140 300
BT40 / PG 15 x 320 XL 8841.73150 24 28 42 55 125 240 320
BT40 / PG 15 x 360 XL 8841.73190 24 28 42 55 125 240 360
BT40 / PG 15 x 400 XL 8841.73230 24 28 42 55 125 240 400
BT40 / PG 25 x 226 XL 8841.76050 40 – 52 – – 140 226
BT40 / PG 25 x 326 XL 8841.76150 40 – 52 – – 240 326
BT50 / PG 10 x 240 XL 8851.71070 16 28 42 31 84 140 240
BT50 / PG 10 x 260 XL 8851.71090 16 28 42 31 84 140 260
BT50 / PG 10 x 300 XL 8851.71130 16 28 42 31 84 140 300
BT50 / PG 10 x 340 XL 8851.71170 16 28 42 31 124 240 340
BT50 / PG 10 x 360 XL 8851.71190 16 28 42 31 124 240 360
BT50 / PG 10 x 400 XL 8851.71230 16 28 42 31 124 240 400
BT50 / PG 15 x 240 XL 8851.73070 24 28 42 55 75 140 240
BT50 / PG 15 x 260 XL 8851.73090 24 28 42 55 75 140 260
BT50 / PG 15 x 300 XL 8851.73130 24 28 42 55 75 140 300
BT50 / PG 15 x 340 XL 8851.73170 24 28 42 55 125 240 340
BT50 / PG 15 x 360 XL 8851.73190 24 28 42 55 125 240 360
BT50 / PG 15 x 400 XL 8851.73230 24 28 42 55 125 240 400
BT50 / PG 25 x 240 XL 8851.76070 40 – 52 – – 140 240
BT50 / PG 25 x 340 XL 8851.76170 40 – 52 – – 240 340 Note: Maximum 5,000 r.p.m.
BT PG XLMAS 403
BT XL Toolholders
PG
17COL1116.1 09/2013
Home
More Technical Information available at WWW.REGO-FIX.COM
Type Part No.D1
[mm]D2
[mm]D3
[mm]L1
[mm]L2
[mm]L3
[mm]L
[mm]
TC40 / PG 10 x 220 XL 8842.71050 16 28 42 31 84 140 220
TC40 / PG 10 x 260 XL 8842.71090 16 28 42 31 84 140 260
TC40 / PG 10 x 300 XL 8842.71130 16 28 42 31 84 140 300
TC40 / PG 10 x 320 XL 8842.71150 16 28 42 31 124 240 320
TC40 / PG 10 x 360 XL 8842.71190 16 28 42 31 124 240 360
TC40 / PG 10 x 400 XL 8842.71230 16 28 42 31 124 240 400
TC40 / PG 15 x 220 XL 8842.73050 24 28 42 55 75 140 220
TC40 / PG 15 x 260 XL 8842.73090 24 28 42 55 75 140 260
TC40 / PG 15 x 300 XL 8842.73130 24 28 42 55 75 140 300
TC40 / PG 15 x 320 XL 8842.73150 24 28 42 55 125 240 320
TC40 / PG 15 x 360 XL 8842.73190 24 28 42 55 125 240 360
TC40 / PG 15 x 400 XL 8842.73230 24 28 42 55 125 240 400
TC40 / PG 25 x 220 XL 8842.76050 40 – 52 – – 140 220
TC40 / PG 25 x 320 XL 8842.76150 40 – 52 – – 240 320
TC50 / PG 10 x 240 XL 8852.71070 16 28 42 31 84 140 240
TC50 / PG 10 x 300 XL 8852.71130 16 28 42 31 84 140 300
TC50 / PG 10 x 340 XL 8852.71170 16 28 42 31 124 240 340
TC50 / PG 10 x 400 XL 8852.71230 16 28 42 31 124 240 400
TC50 / PG 15 x 240 XL 8852.73070 24 28 42 55 75 140 240
TC50 / PG 15 x 300 XL 8852.73130 24 28 42 55 75 140 300
TC50 / PG 15 x 340 XL 8852.73170 24 28 42 55 125 240 340
TC50 / PG 15 x 400 XL 8852.73230 24 28 42 55 125 240 400
TC50 / PG 25 x 320 XL 8852.76150 40 52 240 320
Note: Maximum 5,000 r.p.m.
TC PG XLDIN 69871
TC XL Toolholders
PG
18COL1116.1 09/2013
Home
More Technical Information available at WWW.REGO-FIX.COM
Type Part No.D1
[mm]D2
[mm]D3
[mm]L1
[mm]L2
[mm]L3
[mm]L
[mm]
HSK-A 63 / PG 10 x 240 XL 8865.71070 16 28 42 31 84 140 240
HSK-A 63 / PG 10 x 260 XL 8865.71090 16 28 42 31 84 140 260
HSK-A 63 / PG 10 x 300 XL 8865.71130 16 28 42 31 84 140 300
HSK-A 63 / PG 10 x 340 XL 8865.71170 16 28 42 31 124 240 340
HSK-A 63 / PG 10 x 360 XL 8865.71190 16 28 42 31 124 240 360
HSK-A 63 / PG 10 x 400 XL 8865.71230 16 28 42 31 124 240 400
HSK-A 63 / PG 15 x 240 XL 8865.73070 24 28 42 55 75 140 240
HSK-A 63 / PG 15 x 260 XL 8865.73090 24 28 42 55 75 140 260
HSK-A 63 / PG 15 x 300 XL 8865.73130 24 28 42 55 75 140 300
HSK-A 63 / PG 15 x 340 XL 8865.73170 24 28 42 55 125 240 340
HSK-A 63 / PG 15 x 360 XL 8865.73190 24 28 42 55 125 240 360
HSK-A 63 / PG 15 x 400 XL 8865.73230 24 28 42 55 125 240 400
HSK-A 63 / PG 25 x 240 XL 8865.76070 40 – 52 – – 140 240
HSK-A 63 / PG 25 x 260 XL 8865.76090 40 – 52 – – 140 260
HSK-A 63 / PG 25 x 340 XL 8865.76170 40 – 52 – – 240 340
HSK-A 63 / PG 25 x 360 XL 8865.76190 40 – 52 – – 240 360
HSK-A 100 / PG 10 x 240 XL 8885.71070 16 28 42 31 84 140 240
HSK-A 100 / PG 10 x 300 XL 8885.71130 16 28 42 31 84 140 300
HSK-A 100 / PG 10 x 340 XL 8885.71170 16 28 42 31 124 240 340
HSK-A 100 / PG 10 x 400 XL 8885.71230 16 28 42 31 124 240 400
HSK-A 100 / PG 15 x 240 XL 8885.73070 24 28 42 55 75 140 240
HSK-A 100 / PG 15 x 300 XL 8885.73110 24 28 42 55 75 140 300
HSK-A 100 / PG 15 x 340 XL 8885.73170 24 28 42 55 125 240 340
HSK-A 100 / PG 15 x 400 XL 8885.73230 24 28 42 55 125 240 400
HSK-A 100 / PG 25 x 246 XL 8885.76070 40 – 52 – – 140 246
HSK-A 100 / PG 25 x 346 XL 8885.76170 40 – 52 – – 240 346 Note: Maximum 5,000 r.p.m.
HSK PG XLDIN 69893
HSK XL Toolholders
PG
19COL1116.1 09/2013
Home
More Technical Information available at WWW.REGO-FIX.COM
D2
D3
D1
L1
L2
L3
L
REGO-FIX CAPTO PG XL
Part No. TypeD1
[mm]D2
[mm]D3
[mm]L1
[mm]L2
[mm]L3
[mm]L
[mm]
C6 / PG10 x 225 XL 8886.71050 16 28 42 31 84 140 225
C6 / PG10 x 240 XL 8886.71070 16 28 42 31 84 140 240
C6 / PG10 x 260 XL 8886.71090 16 28 42 31 84 140 260
C6 / PG10 x 300 XL 8886.71130 16 28 42 31 84 140 300
C6 / PG10 x 325 XL 8886.71150 16 28 42 31 124 240 325
C6 / PG10 x 340 XL 8886.71170 16 28 42 31 124 240 340
C6 / PG10 x 360 XL 8886.71190 16 28 42 31 124 240 360
C6 / PG10 x 400 XL 8886.71230 16 28 42 31 124 240 400
C6 / PG15 x 225 XL 8886.73050 24 28 42 55 75 140 225
C6 / PG15 x 240 XL 8886.73070 24 28 42 55 75 140 240
C6 / PG15 x 260 XL 8886.73090 24 28 42 55 75 140 260
C6 / PG15 x 300 XL 8886.73130 24 28 42 55 75 140 300
C6 / PG15 x 325 XL 8886.73150 24 28 42 55 125 240 325
C6 / PG15 x 340 XL 8886.73170 24 28 42 55 125 240 340
C6 / PG15 x 360 XL 8886.73190 24 28 42 55 125 240 360
C6 / PG15 x 400 XL 8886.73230 24 28 42 55 125 240 400
C6 / PG25 x 230 XL 8886.76060 40 – 52 – – 140 230
C6 / PG25 x 330 XL 8886.76160 40 – 52 – – 240 330
C8 / PG10 x 232 XL 8888.71060 16 28 42 31 84 140 232
C8 / PG10 x 332 XL 8888.71160 16 28 42 31 124 240 332
C8 / PG15 x 232 XL 8888.73060 24 28 42 55 75 140 232
C8 / PG15 x 332 XL 8888.73160 24 28 42 55 75 240 332
C8 / PG25 x 230 XL 8888.76060 40 – 52 – – 140 230
C8 / PG25 x 330 XL 8888.76160 40 – 52 – – 240 330 Note: Maximum 5,000 r.p.m.
REGO-FIX CAPTO XL Toolholders
PG
20COL1116.1 09/2013
Home
More Technical Information available at WWW.REGO-FIX.COM
powRgrip® Collets What are PG Collets?
Swiss QualityMade in Switzerland to ISO9001/ISO14001.
What are PG ColletspowRgrip (PG) Collets are precisely engineered to exacting tolerances. This assures that once the collets are pressed into the matching powRgrip holder, the result will be an accurately assembled system of less than 0.0001” TIR. Special metal processing provides the collets unique black appearance and results in an extremely hard surface finish that allows users to experience unmatched longevity and repeatability.
Precision Highest T.I.R. <0.0001” .
Accurate Length Adjustment <10 μmWith integrated adjustment screw.
Clamping of all h6 Tool ShanksCylindrical, WELDON, Whistle-Notch
Clamping of all Shank MaterialsSolid carbide and HSS tool shanks.
Clamping Diameters 0.2 to 25.4 mm
FastClamping in less than 10 seconds.
Simple HandlingParameters are automatically set.
High Vibration Dampening High vibration dampening due to the interface surfaces between the toolholder to collet and the collet to tool shank.
Highest Transferable TorqueThe powRgrip® system yields the highest transferable torque of all comparable systems.
Productivity and Tool LifeSpecially designed to allow for maximum machining capability.
PG
21COL1116.1 09/2013
Home
More Technical Information available at WWW.REGO-FIX.COM
PG Collets do not have a clamping range. Nominal diameter only. Requires h6 tolerance shanks which are listed on page 31.
powRgrip® Collets
Dia.(mm)
Dia.(inch)
PG 10Part No.
PG 10CFPart No.
0.200 1710.00209 –
0.300 1710.00309 –
0.400 1710.00409 –
0.500 1710.00509 –
0.600 1710.00609 –
0.700 1710.00709 –
0.800 1710.00809 –
0.900 1710.00909 –
1.000 1710.01009 –
1.500 1710.01509 –
1.588 1/16 1710.01589 –
2.000 1710.02000 –
2.500 1710.02500 –
3.000 1710.03000 1710.03002
3.500 1710.03500 –
3.175 1/8 1710.03181 1710.03183
4.000 1710.04000 1710.04002
4.500 1710.04500 –
4.763 3/16 1710.04761 1710.04763
5.000 1710.05000 1710.05002
5.500 1710.05500 –
6.000 1710.06000 1710.06002
6.350 1/4 1710.06351 1710.06353
Dia.(mm)
Dia.(inch)
PG 6Part No.
PG 6CFPart No.
0.200 1706.00209 –
0.300 1706.00309 –
0.400 1706.00409 –
0.500 1706.00509 –
0.600 1706.00609 –
0.700 1706.00709 –
0.800 1706.00809 –
0.900 1706.00909 –
1.000 1706.01009 –
1.500 1706.01509 –
2.000 1706.02000 –
2.500 1706.02500 –
3.000 1706.03000 –
3.175 1/8” 1706.03181 –
PG 10 ColletsPG 6 Collets
PG REGO-FIX®
Standard ColletMetallic Sealed
PG REGO-FIX®
Coolant Flush
PG Collet Options
PG
22COL1116.1 09/2013
Home
More Technical Information available at WWW.REGO-FIX.COM
PG REGO-FIX®
Standard ColletMetallic Sealed
PG REGO-FIX®
Coolant Flush
PG Collet Options
Dia.(mm)
Dia.(inch)
PG 15Part No.
PG 15CFPart No.
3.000 1715.03000 1715.03002
3.175 1/8 1715.03181 1715.03183
3.500 1715.03500 –
4.000 1715.04000 1715.04002
4.500 1715.04500 –
4.763 3/16 1715.04761 1715.04763
5.000 1715.05000 1715.05002
5.500 1715.05500 –
6.000 1715.06000 1715.06002
6.350 1/4 1715.06351 1715.06353
7.000 1715.07000 1715.07002
7.938 5/16 1715.07941 1715.07943
8.000 1715.08000 1715.08002
9.000 1715.09000 1715.09002
9.525 3/8 1715.09521 1715.09523
10.000 1715.10000 1715.10002
PG 15 Collets
powRgrip® Collets
Dia.(mm)
Dia.(inch)
PG 25Part No.
PG 25CFPart No.
PG 32Part No.
PG 32CFPart No.
3.000 1725.03000 1725.03002 – –
3.175 1/8 1725.03181 1725.03183 – –
3.500 1725.03500 – – –
4.000 1725.04000 1725.04002 – –
4.500 1725.04500 – – –
4.763 3/16 1725.04761 1725.04763 – –
5.000 1725.05000 1725.05002 – –
5.500 1725.05500 – – –
6.000 1725.06000 1725.06002 1732.06000 1732.06002
6.350 1/4 1725.06351 1725.06353 1732.06351 1732.06353
7.000 1725.07000 1725.70002 1732.07000 1732.07002
7.938 5/16 1725.07941 1725.07943 1732.07941 1732.07943
8.000 1725.08000 1725.08002 1732.08000 1732.08002
9.000 1725.09000 1725.09002 1732.09000 1732.09002
9.525 3/8 1725.09521 1725.09523 1732.09521 1732.09523
10.000 1725.10000 1725.10002 1732.10000 1732.10002
11.000 1725.11000 1725.11002 1732.11000 1732.11002
11.113 7/16 1725.11111 1725.11113 1732.11111 1732.11113
12.000 1725.12000 1725.12002 1732.12000 1732.12002
12.700 1/2 1725.12701 1725.12703 1732.12701 1732.12703
13.000 1725.13000 1725.13002 – –
14.000 1725.14000 1725.14002 1732.14000 1732.14002
14.288 9/16 1725.14291 1725.14293 1732.14291 1732.14293
15.000 1725.15000 1725.15002 – –
15.875 5/8 1725.15881 1725.15883 1732.15881 1732.15883
16.000 1725.16000 1725.16002 1732.16000 1732.16002
17.463 11/16 1175.17461 – – –
18.000 1725.18000 1725.18002 1732.18000 1732.18002
19.050 3/4 1725.19051 1725.19053 1732.19051 1732.19053
20.000 1725.20000 1725.20002 1732.20000 1732.20002
22.000 – – 1732.22000 1732.22002
22.225 7/8 – – 1732.22231 1732.22233
25.000 – – 1732.25000 1732.25002
25.400 1 – – 1732.25401 1732.25403
PG 25 & PG 32 Collets
PG
23COL1116.1 09/2013
Home
More Technical Information available at WWW.REGO-FIX.COM
Ø[mm]
Ø[inch]
PG 15-TPart No.
PG 25-TPart No.
5.000 – 1715.05007 1725.05007
6.000 – 1715.06007 1725.06007
6.350 1/4" 1715.06357 1725.06357
8.000 – 1715.08007 1725.08007
9.525 3/8" 1715.09537 1725.09537
10.000 – 1715.10007 1725.10007
12.000 – – 1725.12007
12.700 1/2” – 1725.12707
16.000 – – 1725.16007
19.050 3/4” – 1725.19057
20.000 – – 1725.20007
The PG boring bar collets bring the ability to transform your normal PG holder into a boring bar holder without losing accuracy or repeatability. The collets are designed to hold the cylindrical boring bar and position it correctly in the PG holder.
Boring Bar Collets PG-T
Boring Bar Collets
PG
24COL1116.1 09/2013
Home
More Technical Information available at WWW.REGO-FIX.COM
secuRgrip PG
secuRgripApplicationspowRgrip now offers an option for those most difficult machinging applications that require the ultimate in cutting tool security. secuRgrip utilizes powRgrips’ tremendous gripping strength in combination with a patented locking key system and threaded cap. These two additional levels of cutting tool security provide an added degree of confidence for those special applications such as expensive castings or complex parts.
Ease of UseUnlike other systems, secuRgrip does not require the purchase of any expensive special modified endmills from limited manufacturers. Instead, it allows for the use of standard Weldon flat tools on any standard carbide or HSS endmill.
LockingThe locking key fits into the Weldon flat prior to assembly and secures the endmill to the collet in this easy to assemble system. A special locking cap then locks the collet and cutter assembly to the holder once pressed in.
PresettingAll secuRgrip collets are designed to provide “z” height adjustment when required. secuRgrip is currently available in both the PG 25 and PG 32 holder series.
Level 1 SecurityLocking Key on
Cutting Tool
Level 2 SecurityLocking Cap for
PG Collet
PG
25COL1116.1 09/2013
Home
More Technical Information available at WWW.REGO-FIX.COM
CAT+ PG-SG HoldersCAT PG-SG Holders
BT+ PG-SG HoldersBT PG-SG Holders
CAT secuRgrip PG
BT secuRgrip PG
TypeREGO-PLUS
D[mm]
L [mm]
Balancing Rings
CAT+ 40 / PG-SG 25 x 3.15” H 5340.72546 46 3.15 FWR 405
CAT+ 40 / PG-SG 25 x 4” H – 46 4 FWR 405
CAT+ 40 / PG-SG 25 x 6” H 5340.72576 46 6 FWR 405/405
CAT+ 40 / PG-SG 32 x 3.5”* 5340.73206 55 3.5 –
CAT+ 40 / PG-SG 32 x 4.3” H – 55 4.3 FWR 505
CAT+ 40 / PG-SG 32 x 6” H 5340.73276 55 6 FWR 505/505
CAT+ 50 / PG-SG 25 x 4” H 5350.72556 46 4 FWR 405
CAT+ 50 / PG-SG 25 x 6” H 5350.72576 46 6 FWR 405/405
CAT+ 50 / PG-SG 32 x 4.3” H 5350.73256 55 4.3 FWR 505
CAT+ 50 / PG-SG 32 x 6” H 5350.73276 55 6 FWR 505/505
* Not for use with balancing rings
TypeStandardPart No.
Form BPart No.
D[mm]
L [mm]
Balancing Rings
CAT 40 / PG-SG 25 x 3.15” H 5340.72541 5340.72544 46 3.15 FWR 405
CAT 40 / PG-SG 25 x 4” H 5340.72551 5340.72554 46 4 FWR 405
CAT 40 / PG-SG 25 x 6” H 5340.72571 5340.72574 46 6 FWR 405/405
CAT 40 / PG-SG 32 x 3.5”* 5340.73201 – 55 3.5 –
CAT 40 / PG-SG 32 x 4.3” H 5340.73251 5340.73254 55 4.3 FWR 505
CAT 40 / PG-SG 32 x 6” H 5340.73271 5340.73274 55 6 FWR 505/505
CAT 50 / PG-SG 25 x 4” H 5350.72551 5350.72554 46 4 FWR 405
CAT 50 / PG-SG 25 x 6” H 5350.72571 5350.72574 46 6 FWR 405/405
CAT 50 / PG-SG 32 x 4.3” H 5350.73251 5350.73254 55 4.3 FWR 505
CAT 50 / PG-SG 32 x 6” H 5350.73271 5350.73274 55 6 FWR 505/505
* Not for use with balancing rings
TypeREGO-PLUS
D[mm]
L [mm]
Balancing Rings
BT+ 40 / PG-SG 25 x 80 H 5140.72546 46 80 FWR 405
BT+ 40 / PG-SG 25 x 120 H 5140.72566 46 120 FWR 405
BT+ 40 / PG-SG 25 x 160 H 5140.72586 46 160 FWR 405/405
BT+ 50 / PG-SG 25 x 120mm H 5150.72566 46 120 FWR 405
BT+ 50 / PG-SG 25 x 160mm H 5150.72586 46 160 FWR 405/405
BT+ 50 / PG-SG 25 x 200 H – 46 200 FWR 405/405
TypeStandardPart No.
Form BPart No.
D[mm]
L [mm]
Balancing Rings
BT 40 / PG-SG 25 x 80 H 5140.72540 5140.72543 46 80 FWR 405
BT 40 / PG-SG 25 x 120 H 5140.72560 5140.72563 46 120 FWR 405
BT 40 / PG-SG 25 x 160 H 5140.72580 5140.72583 46 160 FWR 405/405
BT 50 / PG-SG 25 x 120mm H 5150.72560 – 46 120 FWR 405
BT 50 / PG-SG 25 x 160mm H 5150.72580 – 46 160 FWR 405/405
BT 50 / PG-SG 25 x 200 H 5150.72590 – 46 200 FWR 405/405
“BIG-PLUS SYSTEM - Licensed by BIG Daishowa”
“BIG-PLUS SYSTEM - Licensed by BIG Daishowa”
Standard Form B
PG
26COL1116.1 09/2013
Home
More Technical Information available at WWW.REGO-FIX.COM
HSK A PG-SG Holders
HSK E & F PG-SG Holders
HSK A secuRgrip PG
HSK E & F secuRgrip PG
Type Part No.D
[mm]L
[mm]Balancing
Rings
HSK-A 63 / PG-SG 25 x 100 H 5563.72550 46 100 FWR 405
HSK-A 63 / PG-SG 25 x 120 H 5563.72560 46 120 FWR 405
HSK-A 63 / PG-SG 25 x 160 H 5563.72580 46 160 FWR 405/405
HSK-A 63 / PG-SG 25 x 200 H 5563.72590 46 200 FWR 405/40
HSK-A 63 / PG-SG 32 x 100* 5563.73250 55 100 –
HSK-A 63 / PG-SG 32 x 120 H 5563.73260 55 120 FWR 505
HSK-A 80 / PG-SG 25 x 100 H 5580.72550 46 100 FWR 405
HSK-A 80 / PG-SG 32 x 105 H 5580.73250 55 105 FWR 505
HSK-A 100 / PG-SG 25 x 100 H 5500.72550 46 100 FWR 405
HSK-A 100 / PG-SG 25 x 160 H 5500.72580 46 160 FWR 405/405
HSK-A 100 / PG-SG 25 x 200 H 5500.72590 46 200 FWR 405/405
HSK-A 100 / PG-SG 32 x 100* 5500.73250 55 100 –
HSK-A 100 / PG-SG 32 x 160* 5500.73280 55 160 –
HSK-A 100 / PG-SG 32 x 200* 5500.73290 55 200 –
HSK-A 125 / PG-SG 32 x 110* 5502.73250 55 110 –
* Not for use with balancing rings
Type Part No.D
[mm]L
[mm]Balancing
Rings
HSK-E 63 / PG-SG 25 x 100 H 5563.72554 46 100 FWR 405
HSK-F 63 / PG-SG 25 x 100 H 5563.72555 46 100 FWR 405
HSK-F 63 / PG-SG 25 x 160 H 5563.72585 46 160 FWR 405/405
HSK-F 63 / PG-SG 32 x 100mm 5563.73255 55 100 –
* Not for use with balancing rings
PG
27COL1116.1 09/2013
Home
More Technical Information available at WWW.REGO-FIX.COM
REGO-FIX CAPTO PG-SG Holders
REGO-FIX CAPTO secuRgrip PG
Type Part No.D
[mm]L
[mm]Balancing
Rings
C5 / PG-SG 25 x 80* 5805.72540 46 80 –
C5 / PG-SG 25 x 100 H 5805.72550 46 100 FWR 405
C6 / PG-SG 25 x 085* 5806.72540 46 85 –
C6 / PG-SG 25 x 100 H 5806.72550 46 100 FWR 405
C6 / PG-SG 25 x 120 H 5806.72560 46 120 FWR 405
C6 / PG-SG 25 x 160 H 5806.72580 46 160 FWR 405/405
C6 / PG-SG 32 x 090* 5806.73240 55 90 –
C8 / PG-SG 25 x 092* 5808.72540 46 92 –
C8 / PG-SG 32 x 090* 5808.73240 55 90 –
* Not for use with balancing rings
PG
28COL1116.1 09/2013
Home
More Technical Information available at WWW.REGO-FIX.COM
secuRgrip Replacement Inserts
secuRgrip Wrench Heads & Handles
secuRgrip PG
Type Part No.
PG 25-SG / Ø 12.0 mm 1725.12004S
PG 25-SG / Ø 1/2” 1725.12704S
PG 25-SG / Ø 14.0 mm 1725.14004S
PG 25-SG / Ø 5/8” 1725.15884S
PG 25-SG / Ø 16.0 mm 1725.16004S
PG 25-SG / Ø 18.0 mm 1725.18004S
PG 25-SG / Ø 3/4” 1725.19054S
PG 25-SG / Ø 20.0 mm 1725.20004S
PG 32-SG / Ø 12.0 mm 1732.12004S
PG 32-SG / Ø 1/2” 1732.12704S
PG 32-SG / Ø 14.0 mm 1732.14004S
PG 32-SG / Ø 5/8” 1732.15884S
PG 32-SG / Ø 16.0 mm 1732.16004S
PG 32-SG / Ø 18.0 mm 1732.18004S
PG 32-SG / Ø 3/4” 1732.19054S
PG 32-SG / Ø 20.0 mm 1732.20004S
PG 32-SG / Ø 25.0 mm 1732.25004S
PG 32-SG / Ø 1” 1732.25404SNote: Part Number Includes Insert
Type Part No.
SGI Ø 12.0 mm 7694.12000
SGI Ø 1/2” 7694.12700
SGI Ø 14.0 mm 7694.14000
SGI Ø 5/8” 7694.15880
SGI Ø 16.0 mm 7694.16000
SGI Ø 18.0 mm 7694.18000
SGI Ø 3/4” 7694.19050
SGI Ø 20.0 mm 7694.20000
SGI Ø 25.0 mm 7694.25000
SGI Ø 1” 7694.25400Note: Part Number for Insert Only
Type Part No.
SGN-PG 25 Wrench Head 7654.25000
SGN-PG 32 Wrench Head 7654.32000
SGHM Wrench Handle 8777.77777
secuRgrip Collets with Insert
PG
29COL1116.1 09/2013
Home
More Technical Information available at WWW.REGO-FIX.COM
Type Part No. Description
PGU 9006 A (PG6-PG32) 7610.90160 110 V Machine USA/Canada
APG 906 7611.06900 PG 6 clamping insert
APG 910 7611.10900 PG 10 clamping insert
APG 915 7611.15900 PG 15 clamping insert
APG 925 7611.25900 PG 25 clamping insert
APG 932 7611.32900 PG 32 clamping insert
PGU 9006 automatic clamping unit with push-button operation and auto clamping insert recognition. Designed to make operation easy, fast and reliable. Easy interchangeable inserts and safety interlocks make the machine safe for all operators.
Type Part No. DescriptionMeasurement
W x D x HIncl.
Taper Cleaner
PGC 2506 7621.25069 powRgrip® Compact hydraulic clamping unit 450 x 492 x 280
APC 25 7622.25000 Insert for PGC 2506 for PG 25 toolholders ■APC 15 7622.15000 Insert for PGC 2506 for PG 15 toolholders ■APC 10 7622.10000 Insert for PGC 2506 for PG 10 toolholders ■APC 6 7622.06000 Insert for PGC 2506 for PG 6 toolholders ■
PGC hand pumps offer a price advantage over the PGU units while still performing the task of pressing in tools. The operator actuates the pressure by use of the lever arm until the desired pressure is achieved.
Automatic Machine & Inserts
Handpump & Inserts
PGU 9006 PGC 2506
PG
30COL1116.1 09/2013
Home
More Technical Information available at WWW.REGO-FIX.COM
Taper Cleaner
Cleaning Paper Set
Provides a quick and easy method of cleaning the powRgrip® holder bore of oil and debris before insertion of the tool.
A soft, absorbant paper specially prepared for cleaning the powRgrip® holder bore. The paper is lint-free and chemically neutral. For one time use only! Each pack contains 250 papers.
Type Part No. Description
TKCP 6 7657.06000 Taper cleaner for PG 6 colletholder
TKCP 10 7657.10000 Taper cleaner for PG 10 colletholder
TKCP 15 7657.15000 Taper cleaner for PG 15 colletholder
TKCP 25 7657.25000 Taper cleaner for PG 25 colletholder
TKCP 32 7657.32000 Taper cleaner for PG 32 colletholder
Type Part No. Description
CPS 6 7658.06000 Cleaning paper set for TKCP 6 / 250 papers
CPS 10 7658.10000 Cleaning paper set for TKCP 10 / 250 papers
CPS 15 7658.15000 Cleaning paper set for TKCP 15 / 250 papers
CPS 25 7658.25000 Cleaning paper set for TKCP 25 / 250 papers
CPS 32 7658.32000 Cleaning paper set for TKCP 32 / 250 papers
Matching Products
Presetting Tool
The powRgrip® presetting tool accepts the powRgrip® collets, and is inserted into the toolholder. The tool has a small thumb wheel for precise tool length adjustments, and allows maximum repeatability in the toolholder assembly.
Type Part No. Description
VEW 6 7619.06000 PG 6 Presetting tool for PG 6 colletholder
VEW 10 7619.10000 PG 10 Presetting tool for PG 10 colletholder
VEW 15 7619.15000 PG 15 Presetting tool for PG 15 colletholder
VEW 25 7619.25000 PG 25 Presetting tool for PG 25 colletholder
VEW 32 7619.32000 PG 32 Presetting tool for PG 32 colletholder
PG
31COL1116.1 09/2013
Home
More Technical Information available at WWW.REGO-FIX.COM
powRgrip Technical Requirementsh6 Shank Tolerances
Maximum & Minimum Tool Depth
PG 10 PG 15 PG 25Dia. L L
(min)L
(max)L L
(min)L
(max)L L
(min)L
(max)1/8”, 3/16”
28 24 30 28 25 32 28 25 32
1/4” 33.5 30 35.5 36 33 40 36 33 405/16” 36 33 40 36 33 403/8” 40 37 40.5 40 37 447/16” 40 37 441/2” , 9/16”
45 42 49
5/8” 48 45 503/4” 50 47 50
Fractional Decimal Tolerance Min size1/8 0.125 0.00024 0.124763/16 0.1875 0.00031 0.187191/4 0.25 0.00035 0.249655/16 0.3125 0.00035 0.312153/8 0.375 0.00035 0.374657/16 0.4375 0.00043 0.437071/2 0.5 0.00043 0.499579/16 0.5625 0.00043 0.562075/8 0.625 0.00043 0.624573/4 0.75 0.00051 0.749497/8 0.875 0.00051 0.874491.0 1.000 0.00051 0.99949
LDia.
Metric Tolerance Min size Inch Conv.2.00 0.0060 1.9940 0.078503.00 0.0060 2.9940 0.117874.00 0.0080 3.9920 0.157175.00 0.0080 4.9920 0.196546.00 0.0080 5.9920 0.235917.00 0.0090 6.9910 0.275248.00 0.0090 7.9910 0.314619.00 0.0090 8.9910 0.3539810.00 0.0090 9.9910 0.3933511.00 0.0110 10.9890 0.4326412.00 0.0110 11.9890 0.47201
13.00 0.0110 12.9890 0.5113814.00 0.0110 13.9890 0.5507515.00 0.0110 14.9890 0.5901216.00 0.0110 15.9890 0.6294917.00 0.0110 16.9890 0.6688618.00 0.0110 17.9890 0.7082319.00 0.0130 18.9870 0.7475220.00 0.0130 19.9870 0.7868922.00 0.0130 21.987 0.8656325.00 0.0130 24.987 0.98374
Dia.
1-800-999-7346 WWW.REGO-FIX.COMCOL 1061.2 11/12
PG 6 PG 10 PG 15 PG 25 PG 32Tool Dia (D) L L
(min)L
(max)L L
(min)L
(max)L L
(min)L
(max)L L
(min)L
(max)L L
(min)L
(max)0.2-1.0mm 21.5 26.5 20 241.5mm 23.5 26.5 16 202mm 28 24 26.5 28 25 302.5mm 28 24 26.5 28 25 303mm 28 24 26.5 28 25 30 28 25 30 28 25 32.54mm - 5mm 28 25 30 28 25 30 28 25 40.56mm 36 30 35 36 33 38 36 25 40.5 36 33.5 40.97mm - 9mm 36 33 38 36 33 40.5 36 33.5 40.910mm 40 37 40.5 40 37 44.5 40 35.5 44.911mm 40 37 44.5 40 35.5 44.912mm - 14mm 45 42 49.5 45 40.5 49.916mm – 18mm 48 45.5 50 48 43.5 52.920mm 50 47.5 50 50 45.5 54.922mm 50 45.5 54.925mm 56 49.5 58
PG 6 PG 10 PG 15 PG 25 PG 32Tool Dia.(D) L L
(min)L
(max)L L
(min)L
(max)L L
(min)L
(max)L L
(min)L
(max)L L
(min)L
(max)1/16” 0.925” 1.043” 0.630” 0.787”1/8” 1.102” 0.945” 1.043” 1.102” 0.984” 1.181” 1.102” 0.984” 1.181” 1.102” 0.984” 1.280”3/16” 1.102: 0.984” 1.181” 1.102” 0.984” 1.181” 1.102 0.984” 1.594”1/4” 1.417” 1.181” 1.378” 1.417” 1.299” 1.496” 1.417” 1.299” 1.594” 1.417” 1.319” 1.610”5/16” 1.417” 1.299” 1.496” 1.417” 1.457 1.594” 1.417” 1.319” 1.610”3/8” 1.575” 1.457” 1.594” 1.575” 1.457” 1.752” 1.575” 1.398” 1.768”7/16” 1.575” 1.46” 1.752” 1.575” 1.398” 1.768”1/2” -9/16” 1.772” 1.654” 1.949” 1.772” 1.594” 1.965”5/8”-11/16” 1.890” 1.791” 1.969” 1.890” 1.713” 2.083”3/4” 1.969” 1.870” 1.969” 1.969” 1.791” 2.161”7/8” 1.969” 1.791” 2.161”1” 2.205” 1.949” 2.283”
powRgrip Technical Requirementsh6 Shank Tolerances
Maximum & Minimum Tool Depth
PG 10 PG 15 PG 25Dia. L L
(min)L
(max)L L
(min)L
(max)L L
(min)L
(max)1/8”, 3/16”
28 24 30 28 25 32 28 25 32
1/4” 33.5 30 35.5 36 33 40 36 33 405/16” 36 33 40 36 33 403/8” 40 37 40.5 40 37 447/16” 40 37 441/2” , 9/16”
45 42 49
5/8” 48 45 503/4” 50 47 50
Fractional Decimal Tolerance Min size1/8 0.125 0.00024 0.12476
3/16 0.1875 0.00031 0.187191/4 0.25 0.00035 0.249655/16 0.3125 0.00035 0.312153/8 0.375 0.00035 0.374657/16 0.4375 0.00043 0.437071/2 0.5 0.00043 0.499579/16 0.5625 0.00043 0.562075/8 0.625 0.00043 0.624573/4 0.75 0.00051 0.749497/8 0.875 0.00051 0.874491.0 1.000 0.00051 0.99949
LDia.
Metric Tolerance Min size Inch Conv.2.00 0.0060 1.9940 0.078503.00 0.0060 2.9940 0.117874.00 0.0080 3.9920 0.157175.00 0.0080 4.9920 0.196546.00 0.0080 5.9920 0.235917.00 0.0090 6.9910 0.275248.00 0.0090 7.9910 0.314619.00 0.0090 8.9910 0.35398
10.00 0.0090 9.9910 0.3933511.00 0.0110 10.9890 0.4326412.00 0.0110 11.9890 0.47201
13.00 0.0110 12.9890 0.5113814.00 0.0110 13.9890 0.5507515.00 0.0110 14.9890 0.5901216.00 0.0110 15.9890 0.6294917.00 0.0110 16.9890 0.6688618.00 0.0110 17.9890 0.7082319.00 0.0130 18.9870 0.7475220.00 0.0130 19.9870 0.7868922.00 0.0130 21.987 0.8656325.00 0.0130 24.987 0.98374
Dia.
1-800-999-7346 WWW.REGO-FIX.COMCOL 1061.2 11/12
PG 6 PG 10 PG 15 PG 25 PG 32Tool Dia (D) L L
(min)L
(max)L L
(min)L
(max)L L
(min)L
(max)L L
(min)L
(max)L L
(min)L
(max)0.2-1.0mm 21.5 26.5 20 241.5mm 23.5 26.5 16 202mm 28 24 26.5 28 25 302.5mm 28 24 26.5 28 25 303mm 28 24 26.5 28 25 30 28 25 30 28 25 32.54mm - 5mm 28 25 30 28 25 30 28 25 40.56mm 36 30 35 36 33 38 36 25 40.5 36 33.5 40.97mm - 9mm 36 33 38 36 33 40.5 36 33.5 40.910mm 40 37 40.5 40 37 44.5 40 35.5 44.911mm 40 37 44.5 40 35.5 44.912mm - 14mm 45 42 49.5 45 40.5 49.916mm – 18mm 48 45.5 50 48 43.5 52.920mm 50 47.5 50 50 45.5 54.922mm 50 45.5 54.925mm 56 49.5 58
PG 6 PG 10 PG 15 PG 25 PG 32Tool Dia.(D) L L
(min)L
(max)L L
(min)L
(max)L L
(min)L
(max)L L
(min)L
(max)L L
(min)L
(max)1/16” 0.925” 1.043” 0.630” 0.787”1/8” 1.102” 0.945” 1.043” 1.102” 0.984” 1.181” 1.102” 0.984” 1.181” 1.102” 0.984” 1.280”3/16” 1.102: 0.984” 1.181” 1.102” 0.984” 1.181” 1.102 0.984” 1.594”1/4” 1.417” 1.181” 1.378” 1.417” 1.299” 1.496” 1.417” 1.299” 1.594” 1.417” 1.319” 1.610”5/16” 1.417” 1.299” 1.496” 1.417” 1.457 1.594” 1.417” 1.319” 1.610”3/8” 1.575” 1.457” 1.594” 1.575” 1.457” 1.752” 1.575” 1.398” 1.768”7/16” 1.575” 1.46” 1.752” 1.575” 1.398” 1.768”1/2” -9/16” 1.772” 1.654” 1.949” 1.772” 1.594” 1.965”5/8”-11/16” 1.890” 1.791” 1.969” 1.890” 1.713” 2.083”3/4” 1.969” 1.870” 1.969” 1.969” 1.791” 2.161”7/8” 1.969” 1.791” 2.161”1” 2.205” 1.949” 2.283”
[Inch] PG6 PG 10 PG 15 PG 25 PG 32
Tool Dia (D)Inch
L L(min)
L(max)
L L(min)
L(max)
L L(min)
L(max)
L L(min)
L(max)
L L(min)
L(max)
1/16 .925 1.043 0.630 0.787
1/8 1.102 0.945 1.043 1.102 0.984 1.181 1.102 0.984 1.181 1.102 0.984 1.280
3/16 1.102 0.984 1.181 1.102 0.984 1.181 1.102 0.984 1.594
1/4 1.417 1.181 1.378 1.417 1.299 1.496 1.417 1.299 1.594 1.417 1.319 1.610
5/16 1.417 1.299 1.496 1.417 1.457 1.594 1.417 1.319 1.610
3/8 1.575 1.457 1.594 1.575 1.457 1.752 1.575 1.398 1.768
7/16 1.575 1.460 1.752 1.575 1.398 1.768
1/2 - 9/16 1.772 1.654 1.949 1.772 1.594 1.965
5/8 - 11/16 1.890 1.791 1.969 1.890 1.713 2.083
3/4 1.969 1.870 1.969 1.969 1.791 2.161
7/8 1.969 1.791 2.161
1 2.205 1.949 2.283
[MM] PG6 PG 10 PG 15 PG 25 PG 32
Tool Dia (D)Metric
L L(min)
L(max)
L L(min)
L(max)
L L(min)
L(max)
L L(min)
L(max)
L L(min)
L(max)
0.2 - 1.0 21.5 26.5 20 24
1.5 23.5 26.5 16 20
2 28 24 26.5 28 25 30
2.5 28 24 26.5 28 25 30
3 28 24 26.5 28 25 30 28 25 30 28 25 32.5
4 - 5 28 25 30 28 25 30 28 25 40.5
6 36 30 35 356 33 38 36 25 40.5 36 33.5 40.9
7 - 9 36 33 38 36 33 40.5 36 33.5 40.9
10 40 37 40.5 40 37 44.5 40 35.5 44.9
11 40 37 44.5 40 35.5 44.9
12 - 14 45 42 49.5 45 40.5 49.9
16 - 18 48 45.5 50 48 43.5 52.9
20 50 47.5 50 50 45.5 54.9
22 50 45.5 54.9
25 56 49.5 58
Maximum & Minimum Tool Depth
PG
32COL1116.1 09/2013
Home
More Technical Information available at WWW.REGO-FIX.COM
Weldon Flats
D
L
BA
D L A B
diainch
dia Dh6 inch mm inch mm inch mm
h1h11 mm
inchmax
inchmin
1/2 12.7000 .890 22.620 0.330 8.380 0.440 11.1760
-.011
11.070 0.440 0.436
5/8 15.875 0.953 24.210 0.400 10.160 0.560 14.224 14.110 0.560 0.556
3/4 19.050 1.016 25.797 0.455 11.557 0.675 17.145 14.040 0.675 0.671
1 25.400 1.141 28.972 0.515 13.081 0.925 23.495 -.013 23.365 0.925 0.920
h6 Shank Tolerances
Metric ToleranceMinimum
SizeInch
Conversion
2.00 0.0060 1.9940 0.07850
3.00 0.0060 2.9940 0.11787
4.00 0.0080 3.9920 0.15717
5.00 0.0080 4.9920 0.19654
6.00 0.0080 5.9920 0.23591
7.00 0.0090 6.9910 0.27524
8.00 0.0090 7.9910 0.31461
9.00 0.0090 8.9910 0.35398
10.00 0.0090 9.9910 0.39335
11.00 0.0110 10.9890 0.43264
12.00 0.0110 11.9890 0.47201
13.00 0.0110 12.9890 0.51138
14.00 0.0110 13.9890 0.55075
15.00 0.0110 14.9890 0.59012
16.00 0.0110 15.9890 0.62949
17.00 0.0110 16.9890 0.66886
18.00 0.0110 17.9890 0.70823
19.00 0.0130 18.9870 0.74752
20.00 0.0130 19.9870 0.78689
22.00 0.0130 21.987 0.86563
25.00 0.0130 24.987 0.98374
Fractional Decimal Tolerance Minimum Size
1/8 0.125 0.00024 0.12476
3/16 0.1875 0.00031 0.18719
1/4 0.25 0.00035 0.24965
5/16 0.3125 0.00035 0.31215
3/8 0.375 0.00035 0.37465
7/16 0.4375 0.00043 0.43707
1/2 0.5 0.00043 0.49957
9/16 0.5625 0.00043 0.56207
5/8 0.625 0.00043 0.62457
3/4 0.75 0.00051 0.74949
7/8 0.875 0.00051 0.87449
1 1 0.00051 0.99949