PNEG-250-PM - Hi-Lo and PRO-1 Pan Feeder Parts Poultry... · The Hi-Lo Pan Feeder System is...

PNEG-250-PM

Hi-Lo and PRO-1 Pan Feeder Parts(For installation, refer to PNEG-250)

Parts Manual

PNEG-250-PMVersion: 17.0

Date: 04-25-19

2 PNEG-250-PM Hi-Lo and PRO-1 Pan Feeder Parts

All information, illustrations, photos and specifications in this manual are based on the latestinformation available at the time of publication. The right is reserved to make changes at anytime without notice.

Table of Contents

PNEG-250-PM Hi-Lo and PRO-1 Pan Feeder Parts 3

ContentsChapter 1 Introduction ..........................................................................................................................................4

Chapter 2 Safety .....................................................................................................................................................5Safety Guidelines ...................................................................................................................................5Cautionary Symbols Definitions .............................................................................................................6Safety Cautions ......................................................................................................................................7Safety Sign-Off Sheet ..........................................................................................................................10

Chapter 3 Decals ..................................................................................................................................................11Safety Decals and Placement ..............................................................................................................11

Chapter 4 Parts List .............................................................................................................................................14Hi-Lo Pan Feeder (7098851 and 7101255) .........................................................................................16Hi-Lo Plus Pan Feeder Parts ...............................................................................................................17PRO-1 Assembly ..................................................................................................................................18“E” Feeder Assembly (Short Cone) (C2000416S and C2000423S) ....................................................19Hi-Lo Center House Control Pan with Microswitch (7101534) .............................................................20Hi-Lo End Control Pan with Microswitch (7101482) .............................................................................24Electrical Box Assembly for Micro Control 3 Phase (07101483-3) ......................................................28Electrical Box Assembly for Micro Control (7101483) ..........................................................................30Housing Assembly, Center Control (Prox, Plunger) (C2000526) .........................................................32Center Control Assembly, Prox - 8 Spoke (220V, 1 PH) (C2000521) ..................................................33Hi-Lo Center House Electrical Component for Prox (C2000528) .........................................................34End Control Assembly, Prox (C2000432) ............................................................................................35Housing Assembly, End Control (Prox, Plunger) (C2000431) .............................................................36Hi-Lo Electrical Components for Prox (7100842) .................................................................................38End Control Assembly, Plunger (C2000434) .......................................................................................40Center Control Assembly, Spinner - 8 Spoke (220V, 1 PH) (C2000522) .............................................42Electrical Box Assembly, (Center House Spinner) (C2000525) ...........................................................43Hi-Lo Control Pan Switch Box Assembly (7100407) ............................................................................44End Control Assembly, Spinner (220V) (C2000433) ...........................................................................45End Control Assembly, Spinner (110V) (C2000433-110) ....................................................................46Housing Assembly, End Control (C2000430) ......................................................................................47Hi-Lo Electrical Components (7100211) ..............................................................................................48Hi-Lo Breeder i-Plus3 End Control Pan 1-3/4" (220V, 1 PH) (C2000668) ...........................................50Hi-Lo i-Plus3 End Control Pan (220V, 1 PH) (C2000532) ...................................................................52“E” Feeder i-Plus3 End Control Pan (220V, 1 PH) (C2000559) ...........................................................54Hi-Lo i-Plus3 Center House Control Pan (220V, 1 PH) (C2000560) ....................................................56“E” Feeder i-Plus3 Center House Control Pan (220V, 1 PH) (C2000562) ...........................................58Center Control Assembly (Bolt-On), IR Sensor (220V, 1 PH) (C2000645) ..........................................60“E” Feeder i-Plus3 (Bolt-On) Center House Control Pan (220V, 1 PH) (C2000683) ...........................62Nutrapan i-Plus3 End Control Pan (220V, 1 PH) (C2000555) .............................................................64Nutrapan i-Plus3 Center House Control Pan (220V, 1 PH) (C2000561) .............................................66120 Lbs. Feed Hopper (7098232) ........................................................................................................68200 Lbs. Feed Hopper (7098256) ........................................................................................................69300 Lbs. Feed Hopper (7098715) ........................................................................................................70400 Lbs. Feed Hopper (7099426) ........................................................................................................71Single Boot Assembly ..........................................................................................................................72Double Boot Assembly .........................................................................................................................73Feed Level Control Switch (7051400) ..................................................................................................74Flex-Flo Hopper Level Control Assembly .............................................................................................76Flex-Flo Level Control Switch (FLX-3802) ...........................................................................................78Winching and Miscellaneous Accessories ...........................................................................................80Ceiling Unit Parts .................................................................................................................................84Main Control Parts ...............................................................................................................................85Winch Assembly Parts .........................................................................................................................86650 Lbs. Hopper Scale Assembly (7100751) .......................................................................................88650 Lbs. Hopper Scale Sub-Assembly (C2000297) ............................................................................89

Chapter 5 Warranty ..............................................................................................................................................91


1. Introduction

Cumberland’s Hi-Lo Pan Feeder is a revolutionary two-stage feeder bringing together features and advantages of other systems, and introducing original and effective solutions to some persistent problems and concerns.

The Pan Feeder System is designed to convey granular or powdered poultry feed from external feed bins into the poultry house. It utilizes a screw auger to supply feed to Pan Feeders. The auger and pans are located in the building, and the birds feed directly from it.

Feed is delivered from the feed bin via a feed conveying system such as the Flex-Flo, which is designed to run in conjunction with the Pan Feeder.

For clean out purposes, the Pan Feeder may be raised up to a high level using a winching system. This allows clear access to the building.

The Hi-Lo Pan Feeder System is designed for simple installation, though it is recommended that a specialist be consulted with for the electrical wiring installation.

Because the first 7-10 days of a broiler’s life are critical, the Hi-Lo Pan Feeder rests on the house floor and presents a lip height of 2.1" (5.334 cm) the average height of traditional “feeder lids”. Young chicks can easily get in and out of the pan and are eating out of the pan from day one. And because the pan need not be flooded, they get fresher feed. The Hi-Lo Pan Feeder provides an excellent start for young birds.

As the birds grow, and the feed line is raised, the Hi-Lo Pan Feeder expands into the more easily managed 3.5" (8.89 cm) deep pan.

For larger birds, the higher wall and feed saver lip (wider than the lip currently on the standard grilled feeder) prevent waste from raking and eliminate bill-out. The additional height also compels the birds to eat nearer the edge of the pan, assuring a more even “first in, first out” utilization of feed (which both saves feed and maintains freshness).

Cumberland values customer feedback and suggestions to help determine what features and functions most enhance the efficiency and profitability of operations. Many of Cumberland’s design and manufacturing advantages, including the Hi-Lo Pan Feeder, have been direct responses to customer comments and suggestions.

Please send any questions, suggestions or comments to Cumberland at the following address:

Contact:

Cumberland1004 E. Illinois St.Assumption, IL. 62510Phone: 1-217-226-4421


2. Safety

Safety GuidelinesSafety guidelines are general-to-specific safety rules that must be followed at all times. This manual is written to help you understand safe operating procedures and problems that can be encountered by the operator and other personnel when using this equipment. Read and save these instructions.

As owner or operator, you are responsible for understanding the requirements, hazards and precautions that exist and to inform others as required. Unqualified persons must stay out of the work area at all times.

Alterations must not be made to the equipment. Alterations can produce dangerous situations resulting in SERIOUS INJURY or DEATH.

This equipment must be installed in accordance with the current installation codes and applicable regulations, which must be carefully followed in all cases. Authorities having jurisdiction must be consulted before installations are made.

When necessary, you must consider the installation location relative to electrical, fuel and water utilities.

Personnel operating or working around equipment must read this manual. This manual must be delivered with equipment to its owner. Failure to read this manual and its safety instructions is a misuse of the equipment.

ST-0001-4

2. Safety


Cautionary Symbols Definitions

Cautionary symbols appear in this manual and on product decals. The symbols alert the user of potential safety hazards, prohibited activities and mandatory actions. To help you recognize this information, we use the symbols that are defined below.

NOTICE

DANGER

WARNING

CAUTION

This symbol indicates an imminently hazardous situation which, if not avoided, will result in serious injury or death.

This symbol indicates a potentially hazardous situation which, if not avoided, can result in serious injury or death.

This symbol indicates a potentially hazardous situation which, if not avoided, can result in minor or moderate injury.

This symbol is used to address practices not related to personal injury.

This symbol indicates a general hazard.

This symbol indicates a prohibited activity.

This symbol indicates a mandatory action.

ST-0005-2

2. Safety


Safety Cautions

Use Personal Protective Equipment

Eye Protection

Hearing Protection

Hand Protection

Head Protection

Respiratory Protection

Foot Protection

Fall Protection

• Use appropriate personal protective equipment:

• Wear clothing appropriate to the job.

• Remove all jewelry.

• Tie long hair up and back. ST-0004-1

Follow Safety Instructions

• Carefully read all safety messages in this manual and safety signs on your machine. Keep signs in good condition. Replace missing or damaged safety signs. Be sure new equipment components and repair parts include the current safety signs. Replacement safety signs are available from the manufacturer.

• Learn how to operate the machine and how to use controls properly. Do not let anyone operate without instruction.

• If you do not understand any part of this manual or need assistance, contact your dealer.

ST-0002-1

Maintain Equipment and Work Area

• Understand service procedures before doing work. Keep area clean and dry.

• Never service equipment while it is operating. Keep hands, feet, and clothing away from moving parts.

• Keep your equipment in proper working condition. Replace worn or broken parts immediately.

ST-0003-1

2. Safety


Electrical Safety

An adequate and safe power supply to the Pan Feeder System unit is essential for safety. A competent and qualified electrician must undertake all electrical wiring. All wiring is to be installed according to the National Standards and Regulations relevant to your Country and Region.

A main isolator should be installed with the Pan Feeder System and is essential for safety. This should be installed as indicated in the enclosed installation instructions and in accordance with the relevant codes and directives.

Structural Safety

Raising and lowering the Pan Feeder System in a poultry house imposes additional load on the building. It is essential that the building is able to bear this additional load. Consult a structural engineer to verify the building’s load capacity. Likely/estimated weights of the Pan Feeding System are provided in the table in the Installation Manual.

Correct Use of the Pan Feeder System

The Pan Feeder System is designed solely for the purpose of conveying granular or powdered agricultural feed products for poultry feeding. Use of the system in any other way is a misuse of the system and may endanger safety and health.

Only genuine Cumberland parts are to be used in installation and use of the Pan Feeder System. Use of other non-genuine parts is a misuse of the system and may lead to dangerous situations imperilling the safety and health of you and others.

This machine is not designed for use in atmospheres where there is a risk of explosion. Such environments may include enclosed areas of high dusts concentrations, gas vapors and fumes. Use of the Pan Feeder System in such an environment is prohibited. If in doubt, contact Cumberland or your dealer.

Safety Guards

The Pan Feeder System contains many moving and electrical parts, which will cause serious injury or death if touched. Guards are placed on the machine for your protection. Operating the machine at any time with guards removed or incorrectly fitted is a serious misuse of the machine and endangers safety.

Safety in Handling the Pan Feeding System

To prevent injury, use suitable hand protection when manually handling the components of this system.

Install and Operate Electrical Equipment Properly

• Electrical controls must be installed by a qualified electrician and must meet the standards set by applicable local codes (National Electrical Code for the US, Canadian Electric Code, or EN60204 along with applicable European Directives for Europe).

• Lock-out power source before making adjustments, cleaning, or maintaining equipment.

• Make sure all equipment is properly grounded.ST-0027-4

2. Safety


DustUnder normal working conditions, the Pan Feeder System should create little or no dust hazard. However, some feed materials may create dust when being moved. This dust may be harmful to your health if inhaled. Seek advice from your feed supplier and use a suitable dust mask as needed.

NoiseTests on this machine indicate noise levels at a position 1 meter from the drive unit, 1.6 meters above the ground do not exceed 70 dBa, continuous ‘A’ weighted sound pressure or 63 Pa, instantaneous ‘C’ weighted sound pressure.

Use Caution in the Operation of this EquipmentThe design and manufacture of the Pan Feeding System is directed toward operator safety. However, the very nature of a Pan Feeding System requiring electrical power and possessing moving parts does present a hazard to personnel which cannot be completely safeguarded against without interfering with efficient operation and reasonable access to components.

Continued safe, dependable operation of automatic equipment depends, to a great degree, upon the owner/operator. For a safe and dependable Pan Feeding System, follow the recommendations within this manual and make it a practice to regularly inspect the operation of the unit for any developing problems or unsafe conditions.

READ THESE INSTRUCTIONS BEFORE OPERATION AND SERVICE SAVE FOR FUTURE REFERENCE

1. Read and understand the operating manual before trying to install or operate the Pan Feeding System.

2. Power supply should be OFF for service of electrical components. Use CAUTION in checking voltage or other procedures requiring power to be ON.

3. Never attempt to operate the Pan Feeding System by jumping or otherwise bypassing any safety devices on the unit.

4. Keep the Pan Feeding System clean. Do not allow debris to collect around drive unit, control pan, hoppers or boots.

5. Use CAUTION in working around the Pan Feeding System’s moving parts.

This product is intended for the use of feed handling only. Any other use is considered a misuse of the product.

Some edges of the product’s components are sharp. Examine each product component to determine if there are any safety considerations to be taken prior to use and/or installation. Any and all necessary personal protective equipment should be worn at all times when handling, assembling, installing and operation of the product and/or its components.

Throughout this manual, guards are removed for illustration purposes only. All guards must be in place before and during operation.

For guidance or assistance on any issues relating to the safe use of Pan Feeder System,

Contact:

Cumberland1004 E. Illinois St.Assumption, IL. 62510Phone: 1-217-226-4421

2. Safety


Safety Sign-Off Sheet

Below is a sign-off sheet that can be used to verify that all personnel have read and understood the safety instructions. This sign-off sheet is provided for your convenience and personal record keeping.

Date Employee Name Supervisor Name

ST-0007


3. Decals

Safety Decals and Placement

The safety decals on your equipment are safety indicators which must be carefully read and understood by all personnel involved in the installation, operation, service and maintenance of the equipment.

To replace a damaged or missing decal, contact us to receive a free replacement.

GSI Decals1004 E. Illinois St.Assumption, IL 62510Tel: 1-217-226-4421

Location Decal No. Decals Description

Electrical Control Box Lid

DC-851Decal, CE Electric

Hazard all Pura


DC-889Decal, Danger High Voltage

Under the lid, inside the drivemount and the

housing assemby for

center control

DC-992

Decal, Danger - Rotating Auger Can Crush and

Cut

DC-851

DANGERDANGERHIGH VOLTAGEWill cause injuryor death.Lockout powerbefore servicing.

DC

-889

GSI Group Inc. 217-226-4421

DANGERDANGER

GSI Group 217-226-4421

ROTATING AUGER CANCRUSH AND CUT.Keep clear of movingparts. Disconnect andlockout power beforeservicing.

DC-992

3. Decals


Hi-Lo Control Pan Switch Box

DC-1184Decal, Hi-Lo

Control Panal Switch Box


for Hi-Lo Control Pan Switch Box Assembly

DC-850Decal, European

Certification


for i-Plus3 Control Pan

DC-2282Decal, I-Plus3 Control Pan


ENDCONTROL

CENTERHOUSE

CENTERHOUSE

#1

CENTERHOUSE

#2

DC-1184

DC-850

DC-2282US Pat #8915214

3. Decals


Top Cover Assembly for “E” Feeder

i-Plus3 Control Pan

DC-884Decal, I-Plus3 Control Pan

Hopper Panel Assembly

DC-759Decal,

Cumberland Logo 9.5'' x 5.5''

Hopper Panel Assembly

DC-993Decal, Warning Rotating Auger

Winch DC-857Decal, Warning Rotating Auger


WARNINGROTATING AUGER can crush and dismember.

Keep hands out of feed opening.Lockout power and secure auger before servicing.

DC-759

GSI Group, Inc. 217-226-4421

ROTATING AUGERKeep clear of moving parts.Will cause serious injury.Disconnect and lockoutpower before servicing.

DC-993

WARNING

WARNINGSHEAR POINTKeep hands clear ofdrum and cables.Disconnect and lockoutpower before servicing.

GSI Group Inc. 217-226-4421 DC-857


4. Parts List

1. Hi-Lo Pan Feeder (7098851 and 7101255) - (See Page 16.)

2. Hi-Lo Plus Pan Feeder Parts - (See Page 17.)

3. PRO-1 Assembly - (See Page 18.)

4. “E” Feeder Assembly (Short Cone) (C2000416S and C2000423S) - (See Page 19.)

5. Hi-Lo Center House Control Pan with Microswitch (7101534) - (See Pages 20-23.)

6. Hi-Lo End Control Pan with Microswitch (7101482) - (See Pages 24-27.)

7. Electrical Box Assembly for Micro Control 3 Phase (07101483-3) - (See Pages 28-29.)

8. Electrical Box Assembly for Micro Control (7101483) - (See Pages 30-31.)

9. Housing Assembly, Center Control (Prox, Plunger) (C2000526) - (See Page 32.)

10. Center Control Assembly, Prox - 8 Spoke (220V, 1 PH) (C2000521) - (See Page 33.)

11. Hi-Lo Center House Electrical Component for Prox (C2000528) - (See Page 34.)

12. End Control Assembly, Prox (C2000432) - (See Page 35.)

13. Housing Assembly, End Control (Prox, Plunger) (C2000431) - (See Pages 36-37.)

14. Hi-Lo Electrical Components for Prox (7100842) - (See Pages 38-39.)

15. End Control Assembly, Plunger (C2000434) - (See Pages 40-41.)

16. Center Control Assembly, Spinner - 8 Spoke (220V, 1 PH) (C2000522) - (See Page 42.)

17. Electrical Box Assembly, (Center House Spinner) (C2000525) - (See Page 43.)

18. Hi-Lo Control Pan Switch Box Assembly (7100407) - (See Page 44.)

19. End Control Assembly, Spinner (220V) (C2000433) - (See Page 45.)

20. End Control Assembly, Spinner (110V) (C2000433-110) - (See Page 46.)

21. Housing Assembly, End Control (C2000430) - (See Page 47.)

22. Hi-Lo Electrical Components (7100211) - (See Pages 48-49.)

23. Hi-Lo Breeder i-Plus3 End Control Pan 1-3/4" (220V, 1 PH) (C2000668) - (See Pages 50-51.)

4. Parts List


24. Hi-Lo i-Plus3 End Control Pan (220V, 1 PH) (C2000532) - (See Pages 52-53.)

25. “E” Feeder i-Plus3 End Control Pan (220V, 1 PH) (C2000559) - (See Pages 54-55.)

26. Hi-Lo i-Plus3 Center House Control Pan (220V, 1 PH) (C2000560) - (See Pages 56-57.)

27. “E” Feeder i-Plus3 Center House Control Pan (220V, 1 PH) (C2000562) - (See Pages 58-59.)

28. Center Control Assembly (Bolt-On), IR Sensor (220V, 1 PH) (C2000645) - (See Pages 60-61.)

29. “E” Feeder i-Plus3 (Bolt-On) Center House Control Pan (220V, 1 PH) (C2000683) - (See Pages 62-63.)

30. Nutrapan i-Plus3 End Control Pan (220V, 1 PH) (C2000555) - (See Pages 64-65.)

31. Nutrapan i-Plus3 Center House Control Pan (220V, 1 PH) (C2000561) - (See Pages 66-67.)

32. 120 Lbs. Feed Hopper (7098232) - (See Page 68.)




36. Single Boot Assembly - (See Page 72.)

37. Double Boot Assembly - (See Page 73.)

38. Feed Level Control Switch (7051400) - (See Pages 74-75.)

39. Flex-Flo Hopper Level Control Assembly - (See Pages 76-77.)

40. Flex-Flo Level Control Switch (FLX-3802) - (See Pages 78-79.)

41. Winching and Miscellaneous Accessories - (See Pages 80-83.)

42. Ceiling Unit Parts - (See Page 84.)

43. Main Control Parts - (See Page 85.)

44. Winch Assembly Parts - (See Pages 86-87.)

45. 650 Lbs. Hopper Scale Assembly (7100751) - (See Page 88.)

46. 650 Lbs. Hopper Scale Sub-Assembly (C2000297) - (See Page 89.)

4. Parts List


Hi-Lo Pan Feeder (7098851 and 7101255)

Hi-Lo Pan Feeder (7098851 and 7101255) Parts List

Ref # Part # Description

7101255 Hi-Lo Feeder (8 Spoke)

7098851 Hi-Lo Feeder (14 Spoke)

1 7101254 Hi-Lo Grill (8 Spoke)


2 7100782 Drop Tube

3 7098854 Hi-Lo Feed Level

4 7098855 Hi-Lo Feed Level Stand

5 7098857 Pan, Hi-Lo

4. Parts List


Hi-Lo Plus Pan Feeder Parts

Hi-Lo Plus Pan Feeder Parts List


C2000702 Hi-Lo Feeder (8 Spoke)

C2000703 Hi-Lo Feeder (14 Spoke)

1 C2000690 Cap, Hi-Lo Plus Top

2 C2000694 Ring, Hi-Lo Plus Thread Adjustment

3 C2000689 Tube, Hi-Lo Plus Drop

4 C2000693 Stand, Hi-Lo Plus Feed Level


6 7098857 Pan, Hi-Lo

4. Parts List


PRO-1 Assembly

PRO-1 Assembly Parts List



2 C2000215 Two-Piece Drop Tube

3 C2000209 Drop Tube Extension

4 C2000212 Locking Collar

5 C2000210 Lower Drop Tube

6 C2000307 Clear Window Guard

7 C2000211 Feed Level Adjustor

8 7098857 Pan, Hi-Lo

4. Parts List


“E” Feeder Assembly (Short Cone) (C2000416S and C2000423S)

“E” Feeder Assembly (Short Cone) (C2000416S) Parts List

“E” Feeder Assembly (Short Cone) (C2000423S) Parts List

Ref # Part # Description Qty

1 C2000684 Pan “E” Feeder, Short Cone 1

2 C2000415 Skirt “E” Feeder 1

3 C2000595 Tube Drop “E” Feeder, Extended 1

4 C2000413 Grill “E” Feeder 1




3 C2000596 Tube Drop Bottom, “E” Feeder, 2 Piece, Extended 1


5 C2000410 Cap “E” Feeder 2 Piece Drop 1

C2000416S C2000423S

4. Parts List


Hi-Lo Center House Control Pan with Microswitch (7101534)

4. Parts List


Hi-Lo Center House Control Pan with Microswitch (7101534) (Continued)

4. Parts List


Hi-Lo Center House Control Pan with Microswitch (7101534) Parts List


7101534 Hi-Lo Center House Control Pan with Microswitch

1 7101539 Base Plate Assembly 1

2 7101536 Inner Plate Assembly 1

3 7101538 Lid Assembly 1

4 7101400 Paddle Rest for Micro Control Pan 1

5 C2200010 Anti-Spin Bracket 1

6 7101350 Paddle 1

7 C2000552 Control Pan Drop Tube 1

8 7101537 Body Assembly 1

9 S-2041 Split Lock Washer 1/4" ZN 6

10 S-9468 Bolt, HHTB 1/4"-20 x 1" ZN Grade 5 2

11 S-1102 Hex Nut 1/4"-20 ZN Grade 2 6

12 7101540 Electrical Box Assembly 1

13 7101347 Paddle Cover 1

14 7101346 Retainer Plate 1

15 7101254 Hi-Lo Grill (8 Spoke) 1

16 52-0170 Spring, Adjustable Rod Extension 1

17 AP-2329 Gasket, Foam 1

18 S-1429 Bolt, HHCS 1/4"-20 x 3/4" ZN Grade 2 4

19 S-2010 Nylock Nut #10-24 ZN Grade 2 1

20 S-8183 Screw, SMSA #6 x 3/8" PHP ZN 2

21 S-6151 Lock Washer #10 4

22 S-7139 Screw, MS #10-24 x 3/8" HWHS ZN 4

23 S-849 Hex Nut #10-24 Grade 2 4

24 S-8302 Screw, MS #10-24 x 2-1/4" RHS ZN 2

25 7101348 Paddle Clip 1

26 S-7393 Screw, MS #6-32 x 1/4" PHP ZN Grade 2 2

27 S-6144 Hex Nut #6-32 Grade 2 2

28 7098857 Pan, Hi-Lo 1

29 7098855 Hi-Lo Feed Level Stand 1

30 7098854 Hi-Lo Feed Level 1

31 S-280 Screw, SDS #10-16 x 5/8" HWH ZN 2

32 C2000565 Inlet/Outlet Auger Tube, DBL Swedge, Microswitch Center House Control Pan 1

33 S-8977 Screw, TCSF #10-32 x 3/4" HWH ZN 3

4. Parts List


Hi-Lo End Control Pan with Microswitch (7101482)

4. Parts List


Hi-Lo End Control Pan with Microswitch (7101482) (Continued)

4. Parts List


Hi-Lo End Control Pan with Microswitch (7101482) Parts List


7101482 Hi-Lo End Control Pan with Microswitch

1 7101485A Body Assembly, End Control 1

2 7101342 Base Plate for Micro Control Pan 1

3 7091666 Anchor Plate 1

4 C2200010 Anti-Spin Bracket 1



7 7101487 Mount Plate for Electrical Box Assembly 1

8 7101351 Slope Panel for Micro Control Pan 1

9 7101349 Paddle Shield for Micro Control Pan 1

10 C2000447A Inlet Tube Assembly, Hi-Lo End Control 1

11 7098857 Pan, Hi-Lo 1



14 7101350 Paddle 1

15 7101347 Paddle Cover 1

16 7101346 Retainer Plate 1



19 S-9468 Bolt, HHTB 1/4"-20 x 1" ZN Grade 5 2

20 S-1102 Hex Nut 1/4"-20 ZN Grade 2 6

21 7101483 Electrical Box Assembly for Micro Control Pan 1

22 7101348 Paddle Clip 1


24 S-6144 Hex Nut #6-32 Grade 2 2

25 7101493 Top Plate Assembly for Micro Control Pan 1

26 7097341 Grilled Feeder Control Unit 1

27 AP-2329 Gasket, Foam 1

28 52-0170 Spring, Adjustable Rod Extension 1



31 S-8183 Screw, SMSA #6 x 3/8" PHP ZN 2

32 C2000441 Overflow Bypass Funnel 1


4. Parts List


Electrical Box Assembly for Micro Control 3 Phase (07101483-3)

4. Parts List


Electrical Box Assembly for Micro Control 3 Phase (07101483-3) Parts List


07101483-3 Electrical Box Assembly for Micro Control 3 Phase

1 C2200005 Electrical Box, 4" x 4", with Standoff 1

2 C2200006 Electrical Box Mount Plate Assembly 1

3 FLX-2690 Gasket, 4" x 4" x 3/16" PVC Lid 1

4 FLX-2689 Electrical Box Lid 1

5 S-7377 Screw, MS #10-24 x 1" RHP ZN Grade 2 4

6 S-849 Hex Nut #10-24 Grade 2 4

7 S-8298 Rivet, Solid 1/8" x 1" Long 1

8 AP-2289 Switch Bracket 1

9 C2200025 Microswitch 1

10 S-8183 Screw, SMSA #6-32 x 3/8" PHP ZN 2

11 S-7319 Screw, MS #6-32 x 7/8" RHS ZN Grade 2 2

12 S-6144 Hex Nut #6-32 Grade 2 2

13 C1000028 Relay, GE Mini, 3 Pole 1

14 E160-1075 Tape, Foam Pad, 1 x 1 1

15 DC-851 Decal, CE Electrical Hazard 1

16 DC-889 Decal, Danger High Voltage 1

17 S-3674 #10-24 Washer Zinc 2


4. Parts List


Electrical Box Assembly for Micro Control (7101483)

4. Parts List


Electrical Box Assembly for Micro Control (7101483) Parts List


7101483 Electrical Box Assembly for Micro Control

1 7101490 Drilled Electrical Box 1

2 AP-2289 Switch Bracket 1

3 C2200006 Electrical Box Mount Plate Assembly 1


5 C2200025 Microswitch 1


7 S-8298 Rivet, Solid 1/8" x 1" Long 1


9 S-7319 Screw, MS #6-32 x 7/8" RHS ZN Grade 2 2

10 S-8186 Screw, SMSB #6 x 1/4" PHP ZN 2

11 S-849 Hex Nut #10-24 Grade 2 4

12 S-6144 Hex Nut #6-32 Grade 2 2


14 FH-1310 Connector, Cord Heyco 2

15 FH-1309 Lock Nut 1/2" with Pipe Threads 2

N/S 7098556 Shroud, for 16" Motor Cord 1

N/S 7100348 Cord, 120" Long, 16/3 SJT 1

N/S 7100350 Cord, 28" Long, 16/3 SJT 1

4. Parts List


Housing Assembly, Center Control (Prox, Plunger) (C2000526)

Housing Assembly, Center Control (Prox, Plunger) (C2000526) Parts List


C2000526 Housing Assembly, Center Control (Prox, Plunger)

1 C2000519A Housing Assembly, Center House Control 1

2 C2000543 Inlet/Outlet Tube Assembly, Center House Control Pan 2

3 C2000520A Top Cover 1


5 DC-992 Decal, Danger - Rotating Auger can Crush and Cut 1

4. Parts List


Center Control Assembly, Prox - 8 Spoke (220V, 1 PH) (C2000521)

Center Control Assembly, Prox - 8 Spoke (220V, 1 PH) (C2000521) Parts List


C2000521 Center Control Assembly, Prox - 8 Spoke (220V, 1 PH)

1 C2000526 Housing Assembly, Center Control (Prox, Plunger) 1



4 7098857 Pan, Hi-Lo 1



7 C2000528 Hi-Lo Center House Electrical Component for Prox 1

8 S-1102 Hex Nut 1/4"-20 ZN Grade 2 4


4. Parts List


Hi-Lo Center House Electrical Component for Prox (C2000528)

Hi-Lo Center House Electrical Component for Prox (C2000528) Parts List


C2000525 Hi-Lo Center House Electrical Component for Prox

1 C2000527 Electrical Box, Drilled 1

2 S-7398 3/8" Cord Connector 1

3 FH-1310 Cord Connector, Heyco 1


5 7100275 3/8" Conduit Nut 1

6 S-7368 Switch, DPDT ON-ON Toggle 15 Amp 1

7 7099376 Switch Guard 1

8 S-4322 Cotter Pin 3/32" x 1" Grade 2 1

9 7101128 Relay Assembly for Prox Units 1 Phase 1

10 S-849 Hex Nut #10-24 ZN Grade 2 4

11 FLX-4561 Gasket, Electrical Box 4" x 6" 1

12 FLX-4560 Cover, Electrical Box Lid 4" x 6" 1


14 FLX-4798 Switch, Cap, Prox N.C. 90V-250V 1

15 C2000072 Prox Switch Bracket (SKOV) 1



18 C2000547 Grommet, Rubber, 5/16" I.D. x 13/16" O.D. x 5/16" TH 1

4. Parts List


End Control Assembly, Prox (C2000432)

End Control Assembly, Prox (C2000432) Parts List


C2000432 End Control Assembly, Prox

1 C2000431 Housing Assembly, End Control (Prox, Plunger) 1



4 7098857 Pan, Hi-Lo 1






10 7100842 Hi-Lo Electrical Components for Prox 1

11 S-1102 Hex Nut 1/4"-20 ZN Grade 2 4


4. Parts List


Housing Assembly, End Control (Prox, Plunger) (C2000431)

4. Parts List


Housing Assembly, End Control (Prox, Plunger) (C2000431) Parts List


C2000431 Housing Assembly, End Control (Prox, Plunger)

1 C2000426C Body Assembly, End Control (Prox, Plunger) 1

2 C2000427A Outlet Plate Assembly 1

3 C2000425A Lid Assembly 1

4 C2000428 Motor Mount, End Control Pan 1



4. Parts List


Hi-Lo Electrical Components for Prox (7100842)

4. Parts List


Hi-Lo Electrical Components for Prox (7100842) Parts List


7100842 Hi-Lo Electrical Components for Prox

1 7100380 Electrical Box with Holes 1




5 7100275 3/8" Conduit Nut 1

6 7101128 Relay Assembly for Prox Units 1 Phase 1




10 S-849 Hex Nut #10-24 Grade 2 4



13 FLX-4798 Switch, Cap. Prox N.C. 90V-250V 1

14 C2000072 Prox Switch Bracket (SKOV) 1


N/S 7100348 Cord, 120" Long, 16/3 SJT 1

N/S 7100350 Cord, 28" Long, 16/3 SJT 1

4. Parts List


End Control Assembly, Plunger (C2000434)

4. Parts List


End Control Assembly, Plunger (C2000434) Parts List


C2000434 End Control Assembly, Plunger




4 C2000244 Microswitch Control Pan, Hi-Lo 1






10 C2000440 Hi-Lo Electrical Components for Prox 1

11 S-1102 Hex Nut 1/4"-20 ZN Grade 2 4


4. Parts List


Center Control Assembly, Spinner - 8 Spoke (220V, 1 PH) (C2000522)

Center Control Assembly, Spinner - 8 Spoke (220V, 1 PH) (C2000522) Parts List


C2000522 Center Control Assembly, Spinner - 8 Spoke (220V, 1 PH)




4 7098857 Pan, Hi-Lo 1



7 C2000525 Electrical Box Assembly 1

8 S-1102 Hex Nut 1/4"-20 ZN Grade 2 4


4. Parts List


Electrical Box Assembly, (Center House Spinner) (C2000525)

Electrical Box Assembly, (Center House Spinner) (C2000525) Parts List


C2000525 Electrical Box Assembly, (Center House Spinner)

1 C2000524 Electrical Box, Drilled 1


3 7100275 3/8" Conduit Nut 1

4 S-7399 Jamb Nut 3/8" for Connector, Heyco #8461 1



7 S-849 Hex Nut #10-24 Grade 2 4


9 E171-A1017 DC Spinner Motor 1



4. Parts List


Hi-Lo Control Pan Switch Box Assembly (7100407)

Hi-Lo Control Pan Switch Box Assembly (7100407) Parts List


7100407 Hi-Lo Control Pan Switch Box Assembly

1 7100405 Box, 4" x 4" Electrical, with Holes for Control Pan Switch Box Assembly 1

2 7100410 Box Mount Plate for Hi-Lo Control Pan 1

3 7100623 Switch Guard for Two (2) Switches 1

4 1775 Switch, ON-OFF-OFF, SPDT, 3 Position 2

5 DC-1184 Decal, Hi-Lo Control Pan Switch Box 1

6 S-7272 Cotter Pin 1/8" x 2" ZN Grade 2 1


8 S-7399 Jamb Nut 3/8" for Connector, Heyco #8461 3


10 S-1102 Hex Nut 1/4"-20 ZN Grade 2 4



13 S-7377 Screw, MS #10-24 x 1" RHP ZN Grade 4

14 S-849 Hex Nut #10-24 Grade 2 4

15 7100406 4" x 6" Electrical Box Lid 1



18 DC-850 Decal, European Certification 1

4. Parts List


End Control Assembly, Spinner (220V) (C2000433)

End Control Assembly, Spinner (220V) (C2000433) Parts List


C2000433 End Control Assembly, Spinner (220V)

1 C2000430 Housing Assembly, End Control (Spinner) 1



4 7098857 Pan, Hi-Lo 1






10 7100211 Hi-Lo Electrical Components 1

11 S-1102 Hex Nut 1/4"-20 ZN Grade 2 4


4. Parts List


End Control Assembly, Spinner (110V) (C2000433-110)

End Control Assembly, Spinner (110V) (C2000433-110) Parts List


C2000433-110 End Control Assembly, Spinner (110V)

1 C2000430 Housing Assembly, End Control (Spinner) 1



4 7098857 Pan, Hi-Lo 1






10 7100614 Hi-Lo Electrical Box, 110V 1

11 S-1102 Hex Nut 1/4"-20 ZN Grade 2 4


4. Parts List


Housing Assembly, End Control (C2000430)

Housing Assembly, End Control (C2000430) Parts List


C2000430 Housing Assembly, End Control

1 C2000426E Body Assembly, End Control (Spinner) 1

2 C2000428 Motor Mount, End Control Pan 1

3 C2000425A Lid Assembly 1

4 C2000427A Outlet Plate Assembly 1



4. Parts List


Hi-Lo Electrical Components (7100211)

4. Parts List


Hi-Lo Electrical Components (7100211) Parts List


7100211 Hi-Lo Electrical Components

1 C2000281 Electrical Box (Drilled, 4" x 6") 1


3 7100275 3/8" Conduit Nut 1



6 7100648 Relay Assembly 1

7 E170-A1247 Viscosity Level Switch PC Board 1



10 S-849 Hex Nut #10-24 Grade 2 4



13 S-6525 Hex Nut #8-32 ZN Grade 2 2

14 E171-A1017 DC Spinner Motor 1




N/S 7100348 Cord, 120" Long, 16/3 SJT 1

N/S 7100350 Cord, 28" Long, 16/3 SJT 1

4. Parts List


Hi-Lo Breeder i-Plus3 End Control Pan 1-3/4" (220V, 1 PH) (C2000668)

4. Parts List


Hi-Lo Breeder i-Plus3 End Control Pan 1-3/4" (220V, 1 PH) (C2000668) Parts List


C2000668 Hi-Lo Breeder i-Plus3 End Control Pan 1-3/4" (220V, 1 PH)



3 C2000669 Grill, Breeder 1-3/4" (Drilled) 1

4 7098857 Pan, Hi-Lo 1



7 C2000534 Sensor Assembly, i-Plus3 1




11 C2000535 End Control Box, i-Plus3 1

12 S-1102 Hex Nut 1/4"-20 ZN Grade 2 4

13 S-10209 Threaded Stud, #8-32 x 2", Zinc Plated 3

14 1001-2597 Lock Nut #8-32 KEP Hz Zinc 3



17 S-995 Screw, MS #10-24 x 1" SS 4

18 S-7931 Hex Nut #10-24 SS 4

19 DC-2282 Decal, i-Plus3 Control Pan 1



N/S 7098247 Drive Mount Hardware Package 1

N/S PNEG-1864 Instruction, Wiring Diagram, IR Sensor 1

N/S BX-284 Box, 15-1/2" x 13-3/4" x 14-1/4" 200 C, RSC 1

4. Parts List


Hi-Lo i-Plus3 End Control Pan (220V, 1 PH) (C2000532)

4. Parts List


Hi-Lo i-Plus3 End Control Pan (220V, 1 PH) (C2000532) Parts List


C2000532 Hi-Lo i-Plus3 End Control Pan (220V, 1 PH)




4 7098857 Pan, Hi-Lo 1








12 S-1102 Hex Nut 1/4"-20 ZN Grade 2 4





17 S-7377 Screw, MS #10-24 x 1" RHP ZN Grade 4

18 S-849 Hex Nut #10-24 Grade 2 4






N/S BX-116 Box, 14-1/4" x 14-1/4" x 11-7/8" 200 C, RSC for Pan Control Unit 1

4. Parts List


“E” Feeder i-Plus3 End Control Pan (220V, 1 PH) (C2000559)

4. Parts List


“E” Feeder i-Plus3 End Control Pan (220V, 1 PH) (C2000559) Parts List


C2000559 “E” Feeder i-Plus3 End Control Pan (220V, 1 PH)


2 C2000700H Drop Tube, IR Control, Drilled, “E” Feeder 1





7 C2000514 Cover, Clean Out, Hi-Lo End Control 1




11 S-1102 Hex Nut 1/4"-20 ZN Grade 2 4





16 S-995 Screw, MS #10-24 x 1'' SS 4

17 S-7931 Hex Nut #10-24 SS 4



20 C2000772 Locking Collar, “E” Feeder Control Pans 1

N/S 7098556 Shroud, for 16'' Motor Cord 1



N/S BX-284 Box, 15-1/2" x 13-3/4" x 14-1/4" 200 C, RSC 1

4. Parts List


Hi-Lo i-Plus3 Center House Control Pan (220V, 1 PH) (C2000560)

4. Parts List


Hi-Lo i-Plus3 Center House Control Pan (220V, 1 PH) (C2000560) Parts List


C2000560 Hi-Lo i-Plus3 Center House Control Pan (220V, 1 PH)




4 7098857 Pan, Hi-Lo 1




8 C2000563 Center Control Box, i-Plus3 1

9 S-1102 Hex Nut 1/4"-20 ZN Grade 2 4






15 S-849 Hex Nut #10-24 Grade 2 4




N/S 7099545 Hi-Lo Center House Control Clamp Package 1


N/S BX-116 Box, 14-1/4" x 14-1/4" x 11-7/8" 200 C, RSC for Pan Control Unit 1

4. Parts List


“E” Feeder i-Plus3 Center House Control Pan (220V, 1 PH) (C2000562)

4. Parts List


“E” Feeder i-Plus3 Center House Control Pan (220V, 1 PH) (C2000562) Parts List


C2000562 “E” Feeder i-Plus3 Center House Control Pan (220V, 1 PH)








8 S-1102 Hex Nut 1/4"-20 ZN Grade 2 4





13 S-995 Screw, MS #10-24 x 1" SS 4

14 S-7931 Hex Nut #10-24 SS 4






N/S BX-284 Box, 15-1/2" x 13-3/4" x 14-1/4" 200 C, RSC 1

4. Parts List


Center Control Assembly (Bolt-On), IR Sensor (220V, 1 PH) (C2000645)

4. Parts List


Center Control Assembly (Bolt-On), IR Sensor (220V, 1 PH) (C2000645)


C2000645 Center Control Assembly (Bolt-On), IR Sensor (220V, 1 PH)

1 C2000646A Electrical Box Plate Assembly for Center House IR Control 1


3 C2000647A Top Cover Assembly, IR Center House Control 1






9 7098857 Pan, Hi-Lo 1



12 S-9377 Bolt, 1/4"-20 x 2" ZN Grade 8 2



15 S-6551 Split Lock Washer #8 Med ZN 3

16 S-6525 Hex Nut #8-32 ZN Grade 2 3

17 S-7931 Hex Nut #10-24 SS 4

18 S-1102 Hex Nut 1/4"-20 ZN Grade 2 4

19 S-995 Screw, MS #10-24 x 1" SS 4





N/S BX-284 Box, 15-1/2" x 13-3/4" x 14-1/4" 200 C, RSC 1

4. Parts List


“E” Feeder i-Plus3 (Bolt-On) Center House Control Pan (220V, 1 PH) (C2000683)

4. Parts List


“E” Feeder i-Plus3 (Bolt-On) Center House Control Pan (220V, 1 PH) (C2000683) Parts List


C2000683 “E” Feeder i-Plus3 (Bolt-On) Center House Control Pan (220V, 1 PH)

1 C2000646A Electrical Box Plate Assembly for Center House IR Control 1



4 C2000647 Top Cover Assembly, IR Center House Control 1







11 S-8966 Bolt, HHCS 1/4"-20 x 2-1/4'' ZN Grade 5 2


13 S-10210 Round Spacer, Nylon, 0.166" x 0.3125" x 1" 3


15 S-7931 Hex Nut #10-24 SS 4

16 S-1102 Hex Nut 1/4"-20 ZN Grade 2 4

17 S-995 Screw, MS #10-24 x 1" SS 4



20 DC-884 Decal, Rotating Auger Hazard 1




N/S BX-284 Box, 15-1/2" x 13-3/4" x 14-1/4" 200 C, RSC 1

4. Parts List


Nutrapan i-Plus3 End Control Pan (220V, 1 PH) (C2000555)

4. Parts List


Nutrapan i-Plus3 End Control Pan (220V, 1 PH) (C2000555) Parts List


C2000555 Nutrapan i-Plus3 End Control Pan (220V, 1 PH)


2 C2000700 Drop Tube, IR Control, “E” Feeder/Nutrapan 1

3 6415-1004 Nutrapan Crown 1



6 6415-1026 Nutrapan Center Cone (Short) 1



9 S-1102 Hex Nut 1/4"-20 ZN Grade 2 4

10 S-10299 Threaded Stud, #8-32 x 3/4", Zinc Plated 3




14 S-7931 Hex Nut #10-24 SS 4

15 S-995 Screw, MS #10-24 x 1" SS 4







N/S BX-284 Box, 15-1/2" x 13-3/4" x 14-1/4" 200 C, RSC 1

4. Parts List


Nutrapan i-Plus3 Center House Control Pan (220V, 1 PH) (C2000561)

4. Parts List


Nutrapan i-Plus3 Center House Control Pan (220V, 1 PH) (C2000561) Parts List


C2000561 Nutrapan i-Plus3 Center House Control Pan (220V, 1 PH)


2 C2000700 Drop Tube, IR Control, “E” Feeder/Nutrapan 1

3 6415-1004 Nutrapan Crown 1

4 6415-1026 Nutrapan Center Cone (Short) 1



7 S-1102 Hex Nut 1/4"-20 ZN Grade 2 4

8 S-10299 Threaded Stud, #8-32 x 3/4", Zinc Plated 3




12 S-7931 Hex Nut #10-24 SS 4

13 S-995 Screw, MS #10-24 x 1" SS 4





N/S BX-284 Box, 15-1/2" x 13-3/4" x 14-1/4" 200 C, RSC 1

4. Parts List


120 Lbs. Feed Hopper (7098232)

120 Lbs. Feed Hopper (7098232) Parts List


7098232 120 Lbs. Feed Hopper

1 7098229 Hopper Brace 1

2 7098023 Hopper Panel 4

3 S-6674 Screw, MS 1/4"-20 x 1/2" THS ZN Grade 2 26

4 DC-759 Decal, Cumberland 4-1/2" x 13-1/4" 1

5 DC-993 Decal, Warning Rotating Auger 1


7 S-1102 Hex Nut 1/4"-20 ZN Grade 2 26

8 C2000421 Hopper Suspension Cable Guide 2

9 S-4275 Bolt, HHTB 5/16"-18 x 3/4" ZN Grade 5 10


11 S-7484 Hex Nut 5/16"-18 JS Grade 5 4

12 C2000420 Hopper Suspension Bracket 2

13 S-10268 Flange Nut 5/16"-18 JS Grade 5 10

14 7101093 Hopper Lid (Screen)/120 Lbs., 200 Lbs. 1

4. Parts List









4 7101093 Hopper Lid (Screen)/120 Lbs., 200 Lbs. 1

5 DC-759 Decal, Cumberland 4-1/2 x 13-1/4" 1

6 DC-993 Decal, Warning Rotating Auger 1



9 S-7484 Hex Nut 5/16"-18 JS Grade 5 4


11 S-1102 Hex Nut 1/4"-20 ZN Grade 2 38




4. Parts List










5 S-1102 Hex Nut 1/4"-20 ZN Grade 2 38





10 C2000567 Hopper Suspension Support Bracket 4

11 S-1196 Bolt, HHCS 5/16"-18 x 1" ZN Grade 5 4

4. Parts List












7 C2000567 Hopper Suspension Support Bracket 4

8 S-1196 Bolt, HHCS 5/16"-18 x 1" ZN Grade 5 4



11 S-1102 Hex Nut 1/4"-20 ZN Grade 2 48

4. Parts List


Single Boot Assembly

Single Boot Assembly Parts List


7098103 Single Poultry Boot

1 401906 U-Bolt #10-24 x 1-3/8" Hardened

2 401920 Clamp, Tube with Hardware for 1-3/4" (U-Bolt with Saddle)

3 404238 Iron Ball 3" Hollow 1-1/2#

4 C2000028 Outlet/Inlet Tube

5 7097980 Boot Idler Shaft

6 7098105 Single Body Poultry Boot Assembly

7 7098109 Boot Latch Chain Assembly - 9"

8 7100473 Flat Washer 3/4" I.D. x 1-3/8" O.D.

9 7100649 Plug 5/16" Hole (Shorty)

10 7101070 Insulator, for Feedlines (Red with 1/4" Bore)

11 7101135 Bearing Cap Cover

12 7101372 Insulator Mounting Bracket

13 C1000013 Bearing 3/4" I.D. with Roll Pin Hole

14 S-2010 Nylock Nut #10-24 ZN Grade 2

15 S-7139 Screw, MS #10-24 x 3/8" HWHS ZN

16 S-7307 Nylock Nut 1/4"-20 SS

17 S-8169 Spring Pin 3/16" x 1" Roll Type

18 S-853 Bolt, HHCS 1/4"-20 x 1-1/2" ZN Grade 2

4. Parts List


Double Boot Assembly

Double Boot Assembly Parts List


7098104 Double Poultry Boot

1 401906 U-Bolt #10-24 x 1-3/8" Hardened

2 401920 Clamp, Tube with Hardware for 1-3/4" (U-Bolt with Saddle)

3 404238 Iron Ball 3" Hollow 1-1/2#

4 C2000028 Outlet/Inlet Tube

5 7097980 Boot Idler Shaft

6 7098106 Double Body Poultry Boot Assembly

7 7098109 Boot Latch Chain Assembly - 9"

8 7100437 Flat Washer 3/4" I.D. x 1-3/8" O.D.

9 7100649 Plug 5/16" Hole (Shorty)

10 7101070 Insulator, for Feedlines (Red with 1/4" Bore)

11 7101135 Bearing Cap Cover

12 7101372 Insulator Mounting Bracket

13 C1000013 Bearing 3/4" I.D. with Roll Pin Hole

14 S-2010 Nylock Nut #10-24 ZN Grade 2

15 S-7139 Screw, MS #10-24 x 3/8" HWHS ZN

16 S-7307 Nylock Nut 1/4"-20 SS

17 S-8169 Spring Pin 3/16" x 1" Roll Type

18 S-853 Bolt, HHCS 1/4"-20 x 1-1/2" ZN Grade 2

4. Parts List


Feed Level Control Switch (7051400)

4. Parts List


Feed Level Control Switch (7051400) Parts List


7051400 Feed Level Control Switch

1 272800 Clamp Bracket

2 273000 Mounting Bracket Assembly

3 272900 Adjustment Guide

4 7051600 Back Panel Assembly

5 7051900 Front Panel Assembly

6 7052100 Switch and Paddle Assembly

7 401179 Paddle Cover

8 S-6143 #6-32 x 1" Round Head Machine Screw

9 S-6144 Hex Nut #6-32 ZN Grade 2

10 S-8771 Screw, MS #10-24 x 3/8" RHP ZN Grade 2

11 S-7223 Split Lock Washer #10 ZN

12 S-849 Hex Nut #10-24 Grade 2

13 FH-1310 Connector, Cord Heyco #3231 Replaces: 006-1235-8

N/S FH-1309 Lock Nut 1/2" with Pipe Threads

14 S-1430 1/4" Flat Washer

15 S-4198 1/4"-20 Wing Nut

16 7098183 22" Cord Assembly

4. Parts List


Flex-Flo Hopper Level Control Assembly

4. Parts List


Flex-Flo Hopper Level Control Assembly Parts List


1 FLX-4196 Body Assembly

2 FLX-3939 Paddle Cover

3 7100099 Shroud Assembly

4 FLX-3940 Paddle

5 FLX-3980 Electrical Box Cover

6 1776 Auto Manual Push Button Switch

7 FLX-4805 Paddle Retainer Assembly

8 FH-1310 Connector, Cord Heyco #3231 Replaces: 006-1235-8

9 FH-1309 Lock Nut 1/2" with Pipe Threads

10 S-7223 Split Lock Washer #10 ZN

11 S-849 Hex Nut #10-24 Grade 2

12 S-7213 Screw, SMSAB #10 x 3/8" HWH ZN

13 S-8771 Screw, MS #10-24 x 3/8" RHP ZN Grade 2

14 S-6151 Lock Washer, #10

15 S-7319 Screw, MS #6-32 x 7/8" RHS ZN Grade 2

16 S-6144 Hex Nut #6-32 Grade 2

17 FLX-3981 Mounting Bracket

4. Parts List


Flex-Flo Level Control Switch (FLX-3802)

4. Parts List


Flex-Flo Level Control Switch (FLX-3802) Parts List


FLX-3802 Flex-Flo Feed Level Control Switch

1 FLX-4018 8' 14-3 Male Cord Set

2 FLX-3942 Shroud

3 FLX-3939 Paddle Cover

4 S-4334 #10-32 Hex Nut

5 FLX-3940 Paddle

6 FLX-3981 Mounting Bracket

7 S-6674 Screw, MS 1/4"-20 x 1/2" THS ZN Grade 2

8 S-2041 Split Lock Washer 1/4" ZN

9 S-1102 Hex Nut 1/4"-20 ZN Grade 2

10 FLX-3842 Unimax Switch

11 FLX-4196 Body Assembly

12 FLX-3980 Electrical Box Cover

13 FLX-3943 Paddle Retainer

14 S-6161 #10-16 x 3/8" Washer Head Self-tapping Screw

15 S-7319 Screw, MS #6-32 x 7/8" RHS ZN Grade 2

N/S FLX-3982 Mounting Bracket Holder

N/S S-6381 Heyco 1247 Strain Relief

4. Parts List


Winching and Miscellaneous Accessories

4. Parts List


Winching and Miscellaneous Accessories Parts List

* Parts 1-6 appear on Page 80; parts 7-19 appear on Page 82.


1 7081400 5' Hand Crank for Overhead Winch


2 7081500 5' Electric Drill Crank for Overhead Winch


3 401254 “Flock Shock” Shocker-110/220 Volt AC, 60 Hz

3 7097993 “Flock Shock” Shocker-220 Volt, 50 Hz

4 7097969 Nico Sleeve Crimping Tool

5 S-7308 3/8" x 2-1/4" Lag Screw

6 7098592 “Leedy” 3000 Lbs. Overhead Winch

7 294000 Scissor Hanger

8 7098631 Auger Tube Hanger

9 7099254 Pulley Hanger

10 7097393 1-3/4" Pulley with Eye Bolt

11 7097394 3-1/2" Cast Pulley

12 7097396 1/4" x 3-1/2" Lag Screw Hook

13 7097927 1/4"-20 x 3-1/2" Machine Bolt Hook with Nut

14 7099255 Winch Cable Adjuster

15 S-8762 Clamp, 3/16" Cable Zinc Plated

16 7097498 3/16" x 3/16" Nico Sleeve

17 7097497 1/8" x 3/16" Nico Sleeve

18 CW-2007 Sleeve, 1/16" x 1/16" Nico

19 401190 Shocker Cable Spring

N/S 00401186-1M Cable, Shocker 1/16" 7 x 7 Galvanized - 1000' Spool

N/S 00112073-1M Cable, 3/16" - 7 x 7 Galvanized Aircraft Main Line -1000' Spool

N/S 07097392-1M Cable, 1/8" - 7 x 7 Galvanized Drop 1000' Spool

N/S CW-2008-1M Cord, 1/8"-#4 White Solid Braided - 1000' Spool

4. Parts List


Winching and Miscellaneous Accessories (Continued)

4. Parts List


Winching and Miscellaneous Accessories Parts List

* Parts 1-6 appear on Page 80; parts 7-19 appear on Page 82.






3 401254 “Flock Shock” Shocker-110/220 Volt AC, 60 Hz

3 7097993 “Flock Shock” Shocker-220 Volt, 50 Hz

4 7097969 Nico Sleeve Crimping Tool

5 S-7308 3/8" x 2-1/4" Lag Screw

6 7098592 “Leedy” 3000 Lbs. Overhead Winch

7 294000 Scissor Hanger

8 7098631 Auger Tube Hanger

9 7099254 Pulley Hanger

10 7097393 1-3/4" Pulley with Eye Bolt

11 7097394 3-1/2" Cast Pulley

12 7097396 1/4" x 3-1/2" Lag Screw Hook

13 7097927 1/4"-20 x 3-1/2" Machine Bolt Hook with Nut

14 7099255 Winch Cable Adjuster

15 S-8762 Clamp, 3/16" Cable Zinc Plated

16 7097498 3/16" x 3/16" Nico Sleeve

17 7097497 1/8" x 3/16" Nico Sleeve

18 CW-2007 Sleeve, 1/16" x 1/16" Nico

19 401190 Shocker Cable Spring

N/S 00401186-1M Cable, Shocker 1/16" 7 x 7 Galvanized - 1000' Spool

N/S 00112073-1M Cable, 3/16" - 7 x 7 Galvanized Aircraft Main Line -1000' Spool

N/S 07097392-1M Cable, 1/8" - 7 x 7 Galvanized Drop 1000' Spool

N/S CW-2008-1M Cord, 1/8"-#4 White Solid Braided - 1000' Spool

4. Parts List


Ceiling Unit Parts

Ceiling Unit Parts List


1 7097537 Control Channel

2 7097202 Microswitch

3 7097536 Non-Metallic Control Box

4 7097538 Switch Bracket

5 7097540 Channel Mounting Bracket

6 7097541 Control Box Mounting Bracket

7 7097554 3 PDT Gen Purp Relay

8 7097555 Relay Base

9 7097529 Switch Activator Block

10 E171-A1096 Channel Clip

11 S-4198 1/4"-20 Wing Nut

12 7097640 Overhead Control Box Plate

13 S-6150 6 Gang Terminal Block

4. Parts List


Main Control Parts

Main Control Parts List


1 1775 Switch, ON-OFF-OFF, SPDT, 3 Position

2 7097460 8 Pole Terminal Switch

3 7097476 250V Red Light

4 7097536 Non-Metallic Control Box

5 7097542 Control Box Mount Plate

6 7097641 Main Control Box Plate

7 E160-1137 Ground Plate Assembly

8 7097426 Switch, Momentary

9 FLX-3413 24 Hours Time Clock

10 HH-1442 SPST Toggle Switch

4. Parts List


Winch Assembly Parts

4. Parts List


Winch Assembly Parts List


1 404008 Winch Gearbox

2 7097544 Motor Mount Support

3 7097545 Motor Mount

4 7097580 Cable Drum

5 7097581 Winch Bracket

6 7097582 Motor Adjustment Bracket

7 7097583 Belt Guard

8 7097584 Drive Sheave

9 16-0027 Driven Sheave

10 7097586 “A” V-Belt

11 S-6077 3/8" x 2" U-Bolt

12 7097632F Motor, 1/3 HP 1 PH 60 Hz 115V-208V

13 7099608 Manual Drive Yoke

4. Parts List


650 Lbs. Hopper Scale Assembly (7100751)

650 Lbs. Hopper Scale Assembly (7100751) Parts List


7100751 650 Lbs. Hopper Scale Assembly

1 C2000297 650 Lbs. Hopper Scale Sub-Assembly 1

2 7100655 Hopper Scale Hanger 300, 400, 550# 2

3 7100654 Hopper Scale Hanger 120, 200# 2

4 7100484 Hopper, Scale GS3000 1

4. Parts List


650 Lbs. Hopper Scale Sub-Assembly (C2000297)

650 Lbs. Hopper Scale Sub-Assembly (C2000297) Parts List


C2000297 650 Lbs. Hopper Scale Sub-Assembly

1 7100652 Frame Side 2

2 7100651 Frame Front 2

3 7101393 Scale Beam Stop Bracket 1

4 7100650 Bearing Bracket 1

5 E170-A1007 Switch Box 1



8 S-7484 Hex Nut 5/16"-18 JS Grade 5 10


10 7100484 Hopper, Scale GS3000 1

11 7100653 Frame Hanger 8

12 S-248 Flat Washer 3/8" x 7/16" I.D. x 1" O.D. YDP 8

13 S-7062 Eye Bolt 3/8"-16 x 2-1/4" Zinc 4

14 S-456 Nut 3/8"-16 8

4. Parts List



5. Warranty

Limited Warranty - Protein Products

The GSI Group, LLC. (“GSI”) warrants products which it manufactures, to be free of defects in materials and workmanship under normal usage and conditions for a period of 12 months from the date of purchase (or, if shipped by vessel, 14 months from the date of arrival at the port of discharge). If, in GSI’s sole judgment, a product is found to have a defect in materials and/or workmanship, GSI will, at its own option and expense, repair or replace the product or refund the purchase price. This Limited Warranty is subject to extension and other terms as set forth below.

Warranty Enhancements:

The warranty period for the following products is enhanced as shown below and is in lieu of (and not in addition to) the above stated warranty period.

Conditions and Limitations:THERE ARE NO WARRANTIES THAT EXTEND BEYOND THE LIMITED WARRANTY DESCRIPTION SET FORTH HEREIN; SPECIFICALLY, GSI DISCLAIMS ANY AND ALL OTHER WARRANTIES OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING, WITHOUT LIMITATION, WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR USE IN CONNECTION WITH: (I) ANY PRODUCT MANUFACTURED OR SOLD BY GSI, OR (II) ANY ADVICE, INSTRUCTION, RECOMMENDATION OR SUGGESTION PROVIDED BY AN AGENT, REPRESENTATIVE OR EMPLOYEE OF GSI REGARDING OR RELATED TO THE CONFIGURATION, INSTALLATION, LAYOUT, SUITABILITY FOR A PARTICULAR PURPOSE, OR DESIGN OF SUCH PRODUCTS.

The sole and exclusive remedy for any claimant is set forth in this Limited Warranty and shall not exceed the amount paid for the product purchased. This Warranty only covers the value of the warranted parts and equipment, and does not cover labor charges for removing or installing defective parts, shipping charges with respect to such parts, any applicable sales or other taxes, or any other charges or expenses not specified in this Warranty. GSI shall not be liable for any other direct, indirect, incidental or consequential damages, including, without limitation, loss of anticipated profits or benefits. Expenses incurred by or on behalf of a claimant without prior written authorization from the GSI warranty department shall not be reimbursed. This warranty is not transferable and applies only to the original end user. GSI shall have no obligation or responsibility for any representations or warranties made by or on behalf of any dealer, agent or distributor. Prior to installation, the end user bears all responsibility to comply with federal, state and local codes which apply to the location and installation of the products.

This Limited Warranty extends solely to products sold by GSI and does not cover any parts, components or materials used in conjunction with the product, that are not sold by GSI. GSI assumes no responsibility for claims resulting from construction defects, unauthorized modifications, corrosion or other cosmetic issues caused by storage, application or environmental conditions. Modifications to products not specifically delineated in the manual accompanying the product at initial sale will void all warranties. This Limited Warranty shall not extend to products or parts which have been damaged by negligent use, misuse, alteration, accident or which have been improperly/inadequately maintained.

Service Parts:

GSI warrants, subject to all other conditions described in this Warranty, Service Parts which it manufactures for a period of 12 months from the date of purchase, unless specified in Enhancements above. Parts not manufactured by GSI will carry the Manufacturer’s Warranty.

Product Warranty Period

AP® Fans Performer Series Direct Drive Fan Motor 3 Years * Warranty prorated from material list price:0 to 3 years - no material cost to end user3 to 5 years - end user pays 25%

5 to 7 years - end user pays 50%

7 to 10 years - end user pays 75%

** Warranty prorated from material list price:0 to 3 years - no material cost to end user3 to 5 years - end user pays 75%

AP® and Cumberland® Flex-Flo/Pan Feeding System Motors 2 Years

Electronic Controls All Protein controls manufactured by GSI24 Months from datecode on part

Cumberland®

Feeding and WateringSystems

Feeder System Pan Assemblies 5 Years, Prorated **

Feed Tubes (1.75" and 2.00") 10 Years, Prorated **

Centerless Augers 10 Years, Prorated **

Watering Nipples 10 Years, Prorated **

(Protein Limited Warranty_REV01_06 November 2018)

Copyright © 2019 by The GSI Group, LLCPrinted in the USA

This equipment shall be installed in accordance with the current installation codes and applicable

regulations, which should be carefully followed in all cases. Authorities having jurisdiction should be

consulted before installations are made.

1004 E. Illinois St. Assumption, IL 62510-0020

Phone: 1-217-226-4421 Fax: 1-217-226-4420

www.gsiag.com

CN-342337

Cumberland is a part of GSI, a worldwide brand of AGCO Corporation.

PNEG-250-PM - Hi-Lo and PRO-1 Pan Feeder Parts Poultry... · The Hi-Lo Pan Feeder System is...

Documents

Transcript of PNEG-250-PM - Hi-Lo and PRO-1 Pan Feeder Parts Poultry... · The Hi-Lo Pan Feeder System is...