www.kimray.comE3:20.1

Issued 6/18Current Revision:Update image

BALANCED MOTOR VALVES

PISTON BALANCED PRESSURE OPEN

Stem and Seat AssemblyMotor Valve Diaphragm PressureUpstream PressureDownstream Pressure

Travel Indicator Stem

Stem

Cage

Seat

Oil

Piston

APPLICATIONS: Pilot operated oil or water valve for separators, meters, and water knockouts where a reduced signal pressure is available, and where freezing occurs due to a higher pressure drop.

FEATURES: Piston balanced single seat 10 psig minimum diaphragm pressure Standard 303 stainless valve stem Reinforced oil resistant synthetic rubber diaphragms and seats Easy to service and repair Available for pressure opening or pressure closing service

CERTIFICATIONS: Canadian Registration Number (CRN): 0C15804.24567890NTY (Ductile) 0C15621.24567890NTY (Steel)

SUPPLY PRESSURE: 10 to 35 psig.

OPERATION TEMPERATURE: Standard - 225°F. Max. Heat Modified - 350°F. Max.

CAPACITY: Refer to Table of Contents.

Kimray is an ISO 9001- certified manufacturer.

Cf & Cv VALUESLine Size Trim Size Cf Cv

2" 1.50" 0.79 23.33" 2.25" 0.79 43.84" 3.00" 0.79 70.16" 4.88" 0.79 277.0

www.kimray.comE3:20.3Issued 4/20

Current Revision:Add lifting ring

BALANCED MOTOR VALVES

PISTON BALANCED PRESSURE OPENDUCTILE IRON

ANGLE VALVES AVAILABLE: THRU VALVES AVAILABLE:

ELA 2" SCRD. 250 SMA PB PO-D W/TI 500 500 RFPELC 2" FLGD. 225 FMA PB PO-D W/TI 250 250 RFPELG 3" SCRD. 325 SMA PB PO-D W/TI 250 250 RTRELI 3" FLGD. 325 FMA PB PO-D W/TI 250 250 RTRELM 4" FLGD. 425 FMA PB PO-D W/TI 250 250 RTT

To remove Piston 1807, use Spanner Wrench 1471SNW. To remove Pistons 1859 and 1863, use Spanner Wrench 1859SNW. Note: Drawing depicts 2" valve. Piston design varies, install with spanner wrench holes on top. For dimensions refer to Table of Contents.

EYA 2" SCRD. 250 SMT PB PO-D W/TI 500 500 RFPEYC 2" FLGD. 225 FMT PB PO-D W/TI 250 250 RFPEYG 3" SCRD. 325 SMT PB PO-D W/TI 250 250 RTREYI 3" FLGD. 325 FMT PB PO-D W/TI 250 250 RTREYM 4" FLGD. 425 FMT PB PO-D W/TI 250 250 RTT

*These are recommended spare parts and are stocked as repair kits.

CAT. SIZE MOTOR OPER. MAX NO. TYPE VALVE PRES. W.P. KIT

CAT. SIZE MOTOR OPER. MAX NO. TYPE VALVE PRES. W.P. KIT

1

2

3

4

5

7

8

9

10

6

13

15

16 17

18

19

20

21

23

24

22

25

26

27

28

29

11

12

14

7

26

33

32

31

30

34

*

*

*

*

*

*

*

*

*

*

*

*

*

*

Kimray is an ISO 9001- certified manufacturer.

ITEM QTY. DESCRIPTIONPART NO.

2 INCH 3 INCH 4 INCH

1 1 LOCK NUT 173 906

2 1

SEAT 7498HSN 7499HSN ----

SEAT ---- 165HSN

SEAT DISC ---- 160

3 1 RATIO PLUG 332DEL 333DEL 334

4 1 GASKET 276 277 309

5 1 STEM 1809 327 328

6 1 CAGE ‡ 1751 1759 1761

7 2 O RING 774HSN 329HSN 1872

8 1 O RING 154HSN 155HSN 155

9 BOLT 1672 x 6 1672 x 8

10 1 STEM ASSEMBLY 1808 1858

11 1 STEM GUIDE 2463 2464

12 1 HOUSING 1689 1868D 1869D

13 NUT 241 x 8 241 x 10

14 BOLT 236 x 8 191 x 10

15 1 DIAPHRAGM 6810 6811

16 1 TRAVEL INDICATOR STEM 1687 1733

17 1 TRAVEL INDICATOR HOUSING 1686

18 1 GASKET 1784

19 1 SPRING 1936 551

20 1 BONNET 1671 1867

21 1 BREATHER PLUG 147

22 1 DIAPHRAGM PLATE 133 134

23 1 SPRING 1678 2268

24 1 O RING 1107HSN 639HSN 639

25 2 BACK UP 149T 150T

26 2 BACK UP 1685 1870 1871

27 1 CYLINDER 1679 1861 1865

28 1 O RING 808HSN 802HSN 2083

29 1 O RING 329HSN 330HSN 331

30 1 PISTON SEAL RETAINER 1806 1860 1864SS6

31 1 PISTON 1807 1859 1863SS6

32 1 ORING 265HSN 154HSN 154

33 1 REMOVABLE SEAT 1752PH 1760PH 1762PH

34 1

BODY

SCREWED ANGLE 1819 2379 ----

SCREWED THRU 3081 3086 ----

FLANGED ANGLE 4348 2382 2383

FLANGED THRU 3083 3087 3090

2 LIFTING RING (not shown) ---- 7559

‡ Delrin Cage available on request for 4 inch valves

*

*

*

*

*

*

*

*

*

*

*

*

*

*

www.kimray.comE3:30.1

Issued 1/13Current Revision:Change Logo

LIQUID CAPACITY CHARTS

300 psig Maximum W.P. Valves

CAPACITY-Bbls. Water/Day, Steady Flow

For gravity correction, multiply the above figures byWhere “G” is the specific gravity of the flowing liquid.NOTE: Flow rates are for steady flow conditions over a 24 hour period. Corrections should be made to deal with intermittent flow conditions.

1G

PRESSURE DROP

ACROSS VALVEPSIG

VALVE SIZE - INCHES

2 3 4 6

12345

10152030405060708090

100120140160180200220240260280300325350375400

8001,1501,4001,6001,8002,5503,1003,6004,4005,1005,7006,2506,7507,2007,6508,0508,8509,550

10,20010,80011,40011,95012,50013,00013,50013,95014,50015,05015,60016,100

1,5002,1002,6003,0003,3504,7505,8006,7008,2009,500

10,60011,60012,55013,40014,20015,00016,40017,75018,95020,10021,20022,20023,20024,15025,05025,95027,00028,05029,00029,950

2,4003,4004,1504,8005,3507,6009,300

10,75013,15015,20016,95018,60020,10021,45022,75024,00026,30028,40030,35032,20033,95035,60037,20038,70040,15041,55043,25044,90046,50048,000

9,50013,45016,45019,00021,25030,05036,80042,50052,00060,05067,15073,55079,45084,95090,10094,950

104,050112,350120,150127,400134,300140,850147,150153,150158,900164,500171,200177,700183,900189,950

www.kimray.comE3:40.1

Issued 6/13Current Revision:Remove Cast Iron

BALANCED MOTOR VALVES

CAGE & HARD SEAT

NOTES:

Removable seat and cage is standard in Piston Balanced Motor Valves. But is optional in Diaphragm Balanced Motor Valve. To order specify valve model, then add “with removable seat.”

Kimray is an ISO 9001- certified manufacturer.

www.kimray.comE3:50.1

Issued 6/20Current Revision:Add LPHV valve

BALANCED MOTOR VALVES

DIMENSIONS

ANGLE DIMENSIONS THRU DIMENSIONS

VALVE A B C D E F2" S/FMA 6 1/2 9 8 1/2 4 1/4 3 4 1/4

3" S/FMA 8 1/2 11 3/4 10 1/4 5 1/2 3 3/4 5 1/2

4" FMA 8 1/2 12 1/2 11 6 1/2 4 1/2 6 1/2

6" FMA 10 3/4 — 19 3/4 10 1/4 5 1/2 7 11/16

VALVE A B C D E F2" SMT 6 1/2 10 3/8 9 7/8 2 1/8 — 8 1/2

2" FMT 6 1/2 10 3/8 9 7/8 — 3 9

3" SMT 8 1/2 13 5/16 11 9/16 2 7/8 — 12

3" FMT 8 1/2 13 5/16 11 9/16 — 3 3/4 12 3/16

4" FMT 8 1/2 14 7/8 13 3/8 — 4 1/2 15 1/8

6" FMT 10 3/4 — 19 3/4 — 5 1/2 22

VALVE A B C D E F2" PH 9 1/16 11 9/32 2 29/32 4 1/4 4 1/4 3

3" PH 12 7/8 15 9/32 4 1/32 5 1/2 5 1/2 3 3/4

LPHV DIMENSIONS