Pavement Types
description
Transcript of Pavement Types
CE 2020: Construction Materials Dr. B. Munwar Basha IIT Hyderabad
Pavement Types
CE 2020: Construction Materials Dr. B. Munwar Basha IIT Hyderabad
Vehicle loads
Typical vehicle weighs about 1588 kg, tire pressures around 241 kN/m2
Truck can weigh up to 3.628 tonne with tire pressure of 690 kN/m2
Trucks and busses present a much more significant load on the pavement.
CE 2020: Construction Materials Dr. B. Munwar Basha IIT Hyderabad
Vehicle Volume
Pavements have a design life, and fail after cumulative vehicle exposure.
Volume of vehicles and prediction of vehicle volume is fundamental to pavement design.
CE 2020: Construction Materials Dr. B. Munwar Basha IIT Hyderabad 4
Pavement is the upper part of roadway, airport or parking area structure
It includes all layers resting on the original ground
– It consists of all structural elements or layers, including shoulders
What is a Pavement?
CE 2020: Construction Materials Dr. B. Munwar Basha IIT Hyderabad 5
What is a Pavement? A multi layer system that distributes the
vehicular loads over a larger area
CE 2020: Construction Materials Dr. B. Munwar Basha IIT Hyderabad
Load Distribution Want to distribute the load to avoid
permanent deformation
CE 2020: Construction Materials Dr. B. Munwar Basha IIT Hyderabad 7
Reduce and distribute the traffic loading so as not to damage the subgrade
Provide vehicle access between two points under all-weather conditions
Provide safe, smooth and comfortable ride to road users without undue delays and excessive wear & tear
Meet environmental and aesthetics requirement
Limited noise and air pollution Reasonable economy
Functions of the Pavement
CE 2020: Construction Materials Dr. B. Munwar Basha IIT Hyderabad 8
Sufficient thickness to spread loading to a pressure intensity tolerable by subgade
Sufficiently strong to carry imposed stress due to traffic load
Sufficient thickness to prevent the effect of frost susceptible subgade
Pavement material should be impervious to penetration of surface water which could weaken subgade and subsequently pavement
Pavement material should be non-frost susceptible
Pavement surface should be skid resistant
Requirements of pavement structure
CE 2020: Construction Materials Dr. B. Munwar Basha IIT Hyderabad 9
CE 2020: Construction Materials Dr. B. Munwar Basha IIT Hyderabad 10
Flexible Pavements
PAVEMENTS
Rigid Pavements
Types of Pavement
Asphalt concrete Concrete Pavements
CE 2020: Construction Materials Dr. B. Munwar Basha IIT Hyderabad
Pavement Condition
CE 2020: Construction Materials Dr. B. Munwar Basha IIT Hyderabad
Pavement Condition
CE 2020: Construction Materials Dr. B. Munwar Basha IIT Hyderabad
Pavement Condition
CE 2020: Construction Materials Dr. B. Munwar Basha IIT Hyderabad
Pavement Types Flexible Pavement
Hot mix asphalt (HMA) pavements Called "flexible" since the total pavement
structure bends (or flexes) to accommodate traffic loads
About 82.2% of paved U.S. roads use flexible pavement
Rigid Pavement Portland cement concrete (PCC) pavements Called “rigid” since PCC’s high modulus of
elasticity does not allow them to flex appreciably
About 6.5% of paved U.S. roads use rigid pavement
CE 2020: Construction Materials Dr. B. Munwar Basha IIT Hyderabad
Flexible Pavement
• Base: higher strength material than subbase, often a cementing material is used.
• Cementing material can be portland cement or asphaltic cement, or other material.
CE 2020: Construction Materials Dr. B. Munwar Basha IIT Hyderabad 16
Natural Soil (Subgrade)Aggregate Subbase Course
Aggregate Base CourseAsphalt Concrete
Flexible Pavements
CE 2020: Construction Materials Dr. B. Munwar Basha IIT Hyderabad 17
Given Wheel Load
Load Distribution in Flexible Pavements
Flexible Pavements
150 psi
3 psi
Wearing C.BaseSub-baseSub-grade
CE 2020: Construction Materials Dr. B. Munwar Basha IIT Hyderabad 1
8
Flexible Pavement “A flexible pavement is a structure that
maintains intimate contact with and distributes load to the sub grade and depends on aggregate interlock, particle friction and cohesion for stability”
OR It is a structure which distributes the traffic
loading stresses to the soil (sub grade) at a magnitude that will not shear or distort the soil i.e., from 150 psi to 3 psi
OR Pavement which reflects deformation of sub
grade & the subsequent layers on to the surface” i.e.; load is transmitted from grain to grain through contact points of granular material, i.e. in a compressive way.
CE 2020: Construction Materials Dr. B. Munwar Basha IIT Hyderabad
Flexible Pavement
Structure Surface course
(waterproof, anti-skid) Base course Subbase course Subgrade
CE 2020: Construction Materials Dr. B. Munwar Basha IIT Hyderabad 20
Flexible Pavement
Flexible pavements Elastic Three main layers
Surfacing Wearing course Base course
Road base Sub base
Supported by Sub-grade
Flexible pavements are so named because the total pavement structure deflects, or flexes, under loading. A flexible pavement structure is typically composed of several layers of different materials.
CE 2020: Construction Materials Dr. B. Munwar Basha IIT Hyderabad 21
Load Distribution in Flexible Pavements
Each layer receives the loads from the above layer, spreads them out, then passes on these loads to the next layer below.
Thus, the further down in the pavement structure a particular layer is, the less load (in terms of force per unit area) it must carry.
CE 2020: Construction Materials Dr. B. Munwar Basha IIT Hyderabad 2
2
Structure of Flexible Pavement In order to take maximum advantage of this
property, material layers are usually arranged in order of descending load bearing capacity with the highest load bearing capacity material (and most expensive) on the top and the lowest load bearing capacity material (and least expensive) at the bottom.
Surface Course: This is the top layer and the layer that comes in contact with traffic.
Base Course: This is the layer directly below the surface course and generally consists of aggregates (either stabilized or un-stabilized).
Sub-base Course: This is the layer (or layers) under the base layer. A sub-base is not always needed.
Sub-grade Course: The "sub-grade" is the material upon which the pavement structure is placed. Although there is a tendency to look at pavement performance in terms of pavement structure and mix design alone. The sub-grade can often be the overriding factor in pavement performance.
CE 2020: Construction Materials Dr. B. Munwar Basha IIT Hyderabad 23
Surface Course The surface course is the layer in contact
with traffic loads and normally contains the highest quality materials. It provides characteristics such as friction, smoothness, noise control, rut and shoving resistance and drainage.
In addition, it serves to prevent the entrance of excessive quantities of surface water into the underlying base, sub-base and sub-grade. This top structural layer of material is sometimes subdivided into two layers.
CE 2020: Construction Materials Dr. B. Munwar Basha IIT Hyderabad 2
4
Wearing Course This is the layer in direct contact with traffic
loads. It is meant to take the brunt of traffic wear and can be removed and replaced as it becomes worn. A properly designed (and funded) preservation program should be able to identify pavement surface distress while it is still confined to the wearing course. This way, the wearing course can be rehabilitated before distress propagates into the underlying intermediate/blinder course
Intermediate/Binder Course: This layer provides the bulk of the HMA structure. It's main purpose is to distribute load.
Intermediate/Binder Course
CE 2020: Construction Materials Dr. B. Munwar Basha IIT Hyderabad 25
Base Course The base course is immediately beneath the
surface course. It provides additional load distribution and contributes to drainage and frost resistance. Base courses are usually constructed out of: Aggregates: Base courses are most typically
constructed from durable aggregates that will not be damaged by moisture or frost action. Aggregates can be either stabilized or un-stabilized.
HMA: In certain situations where high base stiffness is desired, base courses can be constructed using a variety of HMA mixes. In relation to surface course HMA mixes, base course mixes usually contain larger maximum aggregate sizes, are more open graded and are subject to more lenient specifications.
CE 2020: Construction Materials Dr. B. Munwar Basha IIT Hyderabad 2
6
Sub-base Course The sub-base course is between the base course
and the sub-grade. It functions primarily as structural support but it can also: Minimize the intrusion of fines from the sub-grade into the
pavement structure. Improves drainage. Minimize frost action damage. Provides a working platform for construction.
The sub-base generally consists of lower quality materials than the base course but better than the sub-grade soils.
A sub-base course is not always needed or used.
For example, a pavement constructed over a high quality, stiff sub-grade may not need the additional features offered by a sub-base course so it may be omitted from design.
CE 2020: Construction Materials Dr. B. Munwar Basha IIT Hyderabad 27
However, a pavement constructed over a low quality soil such as a swelling clay may require the additional load distribution characteristic that a sub-base course can offer. In this scenario the sub-base course may consist of high quality fill used to replace poor quality sub-grade.
Sub-base Course
Sub-grade Although a pavement's wearing course is most
prominent, the success or failure of a pavement is more often than not dependent upon the underlying sub-grade , the material upon which the pavement structure is built.
Sub-grades be composed of a wide range of materials although some are much better than others. This subsection discusses a few of the aspects of sub-grade materials that make them either desirable or undesirable and the typical tests used to characterize sub-grades.
CE 2020: Construction Materials Dr. B. Munwar Basha IIT Hyderabad 28
Sub-grade Preparation Sub-grade Failure Crack
CE 2020: Construction Materials Dr. B. Munwar Basha IIT Hyderabad
Types of Flexible Pavement
Dense-graded
Open-graded
Gap-graded
CE 2020: Construction Materials Dr. B. Munwar Basha IIT Hyderabad 30
Flexible Pavement – Construction
CE 2020: Construction Materials Dr. B. Munwar Basha IIT Hyderabad 3
1
Rigid Pavements
Rigid pavements are so named because the pavement structure deflects very little under loading due to the high modulus of elasticity of their surface course. A rigid pavement structure is typically composed of a PCC surface course built on top of either the sub-grade or an underlying base course.
Introduction
Because of its relative rigidity, the pavement structure distributes loads over a wide area with only one, or at most two, structural layers.
There are other types of surfaces also i.e.; reinforced, continuously reinforced etc.
CE 2020: Construction Materials Dr. B. Munwar Basha IIT Hyderabad 32
Rigid Pavement Rigidity – does not deform under stress
Concrete – air entrained increases resistance to frost damage and de-icing salt corrosion
Reinforcement – may be bars or mesh. Continuous rigid pavements have heavy reinforcement
Joints – used in non-continuous pavements to allow for thermal movement. Includes a ‘filler’ and surface sealant
Rigid pavements – laid as single layer by ‘concrete paver’
CE 2020: Construction Materials Dr. B. Munwar Basha IIT Hyderabad 33
Basic Components of Concrete Pavement
CE 2020: Construction Materials Dr. B. Munwar Basha IIT Hyderabad
Rigid Pavement
CE 2020: Construction Materials Dr. B. Munwar Basha IIT Hyderabad 35
Rigid Pavements
Load Distribution in Rigid Pavements
CE 2020: Construction Materials Dr. B. Munwar Basha IIT Hyderabad
Rigid Pavement
Structure Surface course Base course Subbase course Subgrade
CE 2020: Construction Materials Dr. B. Munwar Basha IIT Hyderabad
Types of Rigid Pavement Jointed Plain Concrete Pavement
(JPCP)
Joints accommodate shrinkage during drying.
CE 2020: Construction Materials Dr. B. Munwar Basha IIT Hyderabad
Types of Rigid Pavement Continuously Reinforced Concrete
Pavement (CRCP)
Photo from the Concrete Reinforcing Steel Institute
CE 2020: Construction Materials Dr. B. Munwar Basha IIT Hyderabad 3
9
Pavements Comparison•Heavy vehicles consume less fuel on rigid pavements
•Rigid pavements more economic when considering environmental / life-cycle costing
CE 2020: Construction Materials Dr. B. Munwar Basha IIT Hyderabad 40
Concrete paver
CE 2020: Construction Materials Dr. B. Munwar Basha IIT Hyderabad 41
Structure of Rigid Pavement
Surface course. This is the top layer, which consists of the PCC slab, reinforced or continuously reinforced slabs .
Base course. This is the layer directly below the PCC layer and generally consists of aggregate or stabilized sub-grade.
Sub-base course. This is the layer (or layers) under the base layer. A sub-base is not always needed and therefore may often be omitted.
CE 2020: Construction Materials Dr. B. Munwar Basha IIT Hyderabad 42
Surface Course• The surface course is the layer in contact with traffic
loads and is made of PCC or RCC. It provides characteristics such as friction, smoothness, noise control and drainage. In addition, it serves as a waterproofing layer to the underlying base, sub-base and sub-grade.
• The surface course can vary in thickness but is usually between 150 mm (6 inches for light loading) and 300 mm (12 inches for heavy loads and high traffic). Figure shows a 300 mm (12 inch) surface course.
PCC Surface Rigid Pavement Slab
(Surface Course) Thickness
CE 2020: Construction Materials Dr. B. Munwar Basha IIT Hyderabad 43
Base Course
• The base course is immediately beneath the surface course. It provides
• Additional load distribution, • Contributes to drainage and frost resistance, • Uniform support to the pavement and • A stable platform for construction equipment. Bases also help
and prevent sub grade soil movement due to slab pumping. Base courses are usually constructed out of:
– Aggregates base. A simple base course of crushed aggregates has been a common option since the early 1900s and is still appropriate in many situations.
CE 2020: Construction Materials Dr. B. Munwar Basha IIT Hyderabad 44
Stabilized aggregate or soil. Stabilizing agents are used to bind otherwise loose particles to one another, providing strength and cohesion. Cement treated bases (CTB s) can be built to as much as 20 - 25 percent of the surface course strength.
Dense-graded HMA. In situations where high base stiffness is desired base courses can be constructed using a dense-graded HMA layer.
Permeable HMA. In certain situations where high base stiffness and excellent drainage is desired, base courses can be constructed using an open graded HMA.
Base Course
CE 2020: Construction Materials Dr. B. Munwar Basha IIT Hyderabad 45
Lean concrete. Contains less Portland cement paste than a typical PCC and is stronger than a stabilized aggregates.
Lean concrete bases (LCB s) can be built to as much as 25 - 50 percent of the surface course strength.
A lean concrete base, functions much like a regular PCC surface course and therefore, it requires construction joints and normally cracks over time. These joints and cracks can potentially cause reflection cracking in the surface course.
Base Course
CE 2020: Construction Materials Dr. B. Munwar Basha IIT Hyderabad 46
Completed CTB with Curing Seal Lean Concrete Base Material
CE 2020: Construction Materials Dr. B. Munwar Basha IIT Hyderabad 47
Sub-base Course
• The sub-base course is the portion of the pavement structure between the base course and the sub-grade. It functions primarily as structural support but it can also: Minimize the intrusion of fines from the sub-grade into the
pavement structure. Improves drainage. Minimizes frost action damage. Provides a working platform for construction.
• The sub-base generally consists of lower quality materials than the base course but better than the sub-grade soils. Appropriate materials are aggregates and high quality structural fill.
CE 2020: Construction Materials Dr. B. Munwar Basha IIT Hyderabad 4
8
Sub grade provides support to the overlying concrete slab. If it is of good quality then slab can be laid over it without providing sub-base otherwise if it is extremely poor then a sub-base layer should be incorporated .
For design purpose the only thing to know about sub-grade is its classification and the unit pressure coming from slab to sub-grade should be calculated for its selection. However, it must be resistant to moisture damages.
Sub-grade
CE 2020: Construction Materials Dr. B. Munwar Basha IIT Hyderabad 4
9
96% of Paved Roads are Asphalt• Today, 96% of all paved roads and
streets in India - almost 45 lakhs kms - are surfaced with asphalt.
• Almost all paving asphalt used today is obtained by processing crude oils. After everything of value is removed, the leftovers are made into asphalt cement for pavement.
• Man-made asphalt (Coal Tar) consists of compounds of hydrogen and carbon with minor proportions of nitrogen, sulfur and oxygen.
• Natural forming asphalt, or brea, also contains mineral deposits.
• The first road use of asphalt occurred in 1824, when asphalt blocks were placed on the Champs-Élysées in Paris.