Panasonic KX-NS1000 V.4.2 Configuration Guide KX... · Configuration Guide for Panasonic KX-NS1000...

Configuration Guide for Panasonic KX-NS1000

1 | P a g e XO Communications Confidential

Panasonic KX-NS1000 V.4.2 Configuration Guide



Table of Contents 1 Introduction .................................................................................................... 3 2 Executive Summary ....................................................................................... 4

3 Software and Hardware Equipment Requirements for Testing ...................... 5 4 Test Configurations ........................................................................................ 6 4.1 Lab Configuration 6 5 Panasonic Configuration ................................................................................ 7



1 Introduction

This document contains the test results of the SIP Trunking used to certify Panasonic IP PBX. This test verified the basic interoperability, features of the appliance, and the integration of the architecture framework. This certification test plan is to be executed in XO’s Plano Certification Laboratory (Plano Lab) which is equipped with different test equipments and is capable to simulate XO’s VoIP network environment.



2 Executive Summary

This report provides the test results found to date for the Panasonic IP PBX SIP Trunking evaluation. The following is a summary addressed the issues and limitation found while performing the test.

“Diversion” header is not working properly so that the Call Forward originated from PSTN and forwarded back to another PSTN number, the 3rd party can only see the 2nd party calling ID instead of the 1st party.

Call Transfer with or without REFER works fine. But the Blind Call Transfer with REFER works but has to use a specific dialing : When the 1st party is talking to the 2nd party, the 2nd party must do the following to make Blind Transfer working - <press Transfer Key>, <press *61 when hearing dial tone>, <press a PSTN number>, <press #>.

Due to no analog port in the machine under test, fax and analog calls are not tested.

Registration Method

Static registration is utilized between the Panasonic IP phones and the XO call agent.

XO SIP Service Packages Supported

Pkg Codec DTMF Fax

1 G.711 RFC 2833 / in-band DTMF T.38 / G.711 pass-through

2 G.729a/G.711 RFC 2833 / in-band DTMF T.38 / G.711 pass-through



3 Software and Hardware Equipment Requirements for Testing

1. Panasonic KX-NS1000 Software version : 4.2

2. 2 Panasonic IP Phones

Model no.: KX-NT 551, KX-NT 556



4 Test Configurations

4.1 Lab Configuration

The following diagram is the configuration used during lab testing.

4693873331

IP Phone – 192.168.0.20

Panasonic

Signal

192.168.0.101

IAD FE 0/1205.158.163.82

255.255.255.248

XO Network

4693873330

IP phone 192.168.0.10

XO Lab Setup for

Panasonic IPPBx Testing

Media

192.168.0.102

192.168.0.199

207.155.151.90

Note: Above lab setup only shows main lab network elements. Above setup shows NAT configuration is required on XO router (IAD) when IPPBX and IP phones have private IPs.

For detail, please refer to the attachment of IAD configuration.



5 Panasonic Configuration

Main screen



Virtual slot



Virtual Port - (Virtual SIP Gateway – Shelf Property)

*Make sure SIP Client port number should be 5060.



IP Address for Signaling IP Address of IPPBX - (NAT) internal: 192.168.0.101, external: 207.155.151.90 IP Address for Media IP Address of IPPBX – 192.168.0.102 Default Gateway -> IP Address of XO Router (IAD) – 192.168.0.1



VOIP port setting – Main IP Address -> XO NBS IP Address



VOIP port setting - Account



VOIP port setting – Registration (Disable – due to static SIP)



VOIP port setting - Option



VOIP port setting - Calling party



VOIP port setting - RTP/RTCP (DSCP bit configuration)



VOIP port setting - Codec settings:



VOIP port setting - Codec settings (continue): (shows Fax / DTMF configuration)



VOIP port setting - “Supplementary Service” – CNIP (receive) – ‘Yes’ to display inbound CNAM; Blind/Attended Transfer (REFER) is enabled.



Trunk settings:



COS settings for trunk:



DID settings:



Group priority setting



Numbering plan

Incoming call distribution group (Hunt group)



Normal “Hunt Group”

“Extension No Answer Redirection Timer” to find next member



“Overflow No Answer”



Extension settings:



Call forward settings done from extension: (below screen shot was for call forward always to 9725786857)

Intercept (to VM)



Intercept time (‘0’ indicates ‘default system time’ = 10 sec for lab)

Voice Mail



CLIP



Auto Attendant

Panasonic Software Version under test :

Panasonic KX-NS1000 V.4.2 Configuration Guide KX... · Configuration Guide for Panasonic KX-NS1000...

Documents

Transcript of Panasonic KX-NS1000 V.4.2 Configuration Guide KX... · Configuration Guide for Panasonic KX-NS1000...