Oxnard Union High School District - PROJECT …...Oxnard Union High School District Project #...

Oxnard Union High School District Bid #574

Hueneme High School Construction of Site Improvements and

Alterations to Path of Travel

PROJECT MANUAL CONSTRUCTION DOCUMENTS

ADDENDUM #3

SEPTEMBER 14, 2017

BLANK PAGE

Oxnard Union High School District Project # 016114.01

Hueneme High School Addendum #3, 09/14/18

Construction of Site Improvements and Alterations to Path of Travel

Construction Documents

SOLID PLASTIC TOILET COMPARTMENTS 10 21 16 - 1

SECTION 10 21 16

SOLID PLASTIC TOILET COMPARTMENTS

PART 1 GENERAL

1.1 SUMMARY

A. Section Includes: 1. Solid plastic toilet compartments and urinal screens

B. Related Sections: 1. Division 01: Administrative, procedural, and temporary work requirements.

1.2 REFERENCES

A. ASTM International (ASTM): 1. A167 - Standard Specification for Stainless and Heat-Resisting Chromium-Nickel Steel

Plate, Sheet, and Strip.

2. B221 - Standard Specification for Aluminum and Aluminum-Alloy Extruded Bars, Rods, Wire, Profiles, and Tubes.

3. E84 - Standard Test Method for Surface Burning Characteristics of Building Materials.

B. National Fire Protection Association (NFPA) 286 - Standard Methods of Fire Tests for Evaluating Contribution of Wall and Ceiling Interior Finish to Room Fire Growth.

1.3 SYSTEM DESCRIPTION

A. Compartment Configurations: 1. Toilet partitions Floor mounted, overhead braced. 2. Urinal screens: Wall mounted.

1.4 SUBMITTALS

A. Submittals for Review: 1. Shop Drawings: Include dimensioned layout, elevations, trim, closures, and

accessories.

2. Product Data: Manufacturer's descriptive data for panels, hardware, and accessories. 3. Samples: 2 x 3 inch samples showing available colors.

B. Sustainable Design Submittals: 1. Recycled Content: Certify percentages of post-consumer and pre-consumer recycled






content.

2. Regional Materials: Certify distance between manufacturer and Project and between manufacturer and extraction or harvest point in miles.

1.5 QUALITY ASSURANCE

A. Manufacturer Qualifications: Minimum 5 years experience in manufacture of solid plastic toilet compartments with products in satisfactory use under similar service conditions.

B. Installer Qualifications: Minimum 5 years experience in work of this Section.

1.6 WARRANTIES

A. Provide manufacturer’s 25 year warranty against breakage, corrosion, and delamination under normal conditions.

PART 2 PRODUCTS

2.1 MANUFACTURERS

A. Contract Documents are based on products by Bobrick SierraSeries 1090 Series Overhead-Braced Water- and Fire-Resistant Solid Color Reinforced Composite Toilet Partitions and

Urinal Screens

(http://www.bobrick.com/toiletpartitionsystems/Pages/SolidColorReinforcedComposite.aspx)

B. Or Equal

2.2 MATERIALS

A. Doors, Panels and Pilasters: 1. High density polyethylene (HDPE), fabricated from polymer resins compounded under

high pressure, forming single thickness panel.

2. Waterproof and nonabsorbent, with self-lubricating surface, resistant to marks by pens, pencils, markers, and other writing instruments.

3. 1 inch thick with edges rounded to 1/4 inch radius. 4. Recycled content: Minimum 25 percent 5. Fire hazard classification: Class A flame spread/smoke developed rating, tested to

ASTM E84.

6. Color: To be selected from manufacturer’s full color range.

B. Aluminum Extrusions: ASTM B221, 6463-T5 alloy and temper.

C. Stainless Steel: ASTM A167, Type 304.

(http:/www.bobrick.com/toiletpartitionsystems/Pages/SolidColorReinforcedComposite.aspx






2.3 HARDWARE

A. Hinges: 1. 8 inches long, fabricated from heavy-duty extruded aluminum with bright dip anodized

finish, wrap-around flanges, adjustable on 30-degree increments, through bolted to

doors and pilasters with stainless steel, Torx head sex bolts.

2. Hinges operate on field-adjustable nylon cams, field adjustable in 30 degree increments.

3. Doors to have automatic closing device.

B. Door Strike and Keeper: 1. 6 inches long, fabricate from heavy-duty extruded aluminum with bright dip anodized

finish, with wrap-around flanges secured to pilasters with stainless steel tamper

resistant Torx head sex bolts.

2. Bumper: Extruded black vinyl.

C. Latch and Housing: 1. Heavy-duty extruded aluminum. 2. U-shaped handle below latch 3. Latch housing: Bright dip anodized finish. 4. Slide bolt and button: Black anodized finish.

D. Bumper: 1. Chrome plated Zamak. 2. Equip outswing handicapped doors with second door pull and door stop.

E. Door Pulls: Chrome plated Zamak.

2.4 COMPONENTS

A. Doors and Dividing Panels: 55 inches high, mounted 14 inches above finished floor, with aluminum heat-sinc fastened to bottom edges.

B. Pilasters: 82 inches high, fastened to pilaster sleeves with stainless steel tamper resistant Torx head sex bolt.

C. Pilaster Sleeves: 3 inches high, one-piece molded HDPE secured to pilaster with stainless steel tamper resistant Torx head sex bolt.

D. Wall Brackets: 54 inches long, heavy-duty aluminum, bright dip anodized finish, fastened to pilasters and panels with stainless steel tamper resistant Torx head sex bolts.

E. Headrail: Heavy-duty extruded aluminum, anti-grip design, clear anodized finish, fastened to headrail bracket with stainless steel tamper resistant Torx head sex bolt and at top of pilaster

with stainless steel tamper resistant Torx head screws.

F. Headrail Brackets: 20 gage stainless steel, satin finish, secured to wall with stainless steel






tamper resistant Torx head screws.

PART 3 EXECUTION

3.1 INSTALLATION

A. Install compartments in accordance with manufacturer’s instructions and approved Shop Drawings.

B. Install rigid, straight, plumb, and level.

C. Locate bottom edge of doors and panels 14 inches above finished floor.

D. Provide uniform, maximum 3/8 inch vertical clearance at doors.

E. Not Acceptable: Evidence of cutting, drilling, or patching.

3.2 ADJUSTING

A. Adjust doors and latches to operate correctly.

END OF SECTION

Oxnard Union High School District Bid #574

ADDENDUM #3 SEPTEMBER 14, 2017

APPENDIX A

BLANK PAGE

Model # 338SH3-V

7/30/2012 Page 1 of 13

1675 Locust StreetRed Bud, IL 62278

Phone: 618-282-8200Fax: 618-282-8202

WARRANTY & TERMS

WARRANTY: 5 Year Limited Warranty on Thermoplastic coated elements. Ultra Play guarantees all items for one full year to be free of defects in workmanship or materials when installed and maintained properly. We agree to repair or replace, any items determined to be defective. Items specifically not covered by this warranty include vandalism, man made or natural disasters, lack of maintenance, normal weathering or wear and tear due to public abuse.

Damages or loss in transit is the responsibility of the carrier, whether visible or concealed. It is the responsibility of the recipient to assure that the order is received complete. Before signing the delivery receipt, inspect the shipment immediately and completely. Note any damages or shortages on the bill of lading. Damage reports must be filed within 10 days. Ultra Play is NOT responsible for damages or loss in transit. Title to all goods passes to the customer at the time of shipment. Ultra Play will assist in filing claims if the freight arrangements were made by Ultra Play at your request.

CANCELLATIONS AND RETURNS: Cancellations are only accepted with approval of Ultra Play. No merchandise shall be returned without a Return Goods Authorization number which is issued by customer service. Any authorized merchandise must be carefully packed and received in saleable condition. A restocking charge of up to 25% will be applied to all returned goods when the error is not the fault of Ultra Play. All returns must be shipped freight prepaid.

7/30/2012 Page 2 of 13

Owners and installers please note these safety warnings and make use of this checklist on a regular basis.•

Follow installation instructions when erecting equipment.•

Ground surfaces around equipment should be restored as needed. Concrete footings should never be exposed. Surface depth •should comply with ASTM and CPSC specifications.

Check for and repair damage caused by wear or vandalism, a major factor in injury causing situations.•

All protruding bolts should be covered or cut off and finished smooth. Sharp edges on pipes should be capped or removed. Check •for bent, broken, or severly worn pipe, and replace.

All equipment should be free of rust and repainted whenever necessary to deter rusting.•

We provide our customers with layout sheets and installation instructions. Please keep on file the specifications sheet that contains •the listing of every part used.

Never add components not intended for use with this product.•

Regular maintenance is necessary in this and all park and recreational equipment to insure the safety of the user.•

Note: Proper maintenance of equipment requires regular tightening of all bolts, nuts, and setscrews.•

Note: Regular checking of all parts, castings, etc. should be made. If a part is broken or worn, it shoud be replaced immediatly.•

Check to be sure all fittings are tight and that bars and pipes do not move.•

Replace all worn S-hooks. S-hooks must be completely closed. Failure to close S-hooks can result in serious injury to the user. •NEVER reuse S-hooks.

Test for free movement of swing hanger and other moving attached parts.•

Check for worn chains and replace them.•

A soft resilient surface should be placed under all swings extending at least twice the height of the top rail both front and back. •

SAFETY WARNINGS & EQUIPMENT INSPECTION

7/30/2012 Page 3 of 13

3/8" Washer

7/16" x 5-1/2"Machine Bolt 7/16" Washer

5/16" Washer

7/16" Hex Nut

3/8" Hex Nut

5/16" x 1"Machine Bolt

3/8" x 1"Carriage Bolt

5/16" Kep Nut

800-45-ULTRA www.ultrasite.com

HARDWARE

7/30/2012 Page 4 of 13


1/2", 9/16", & 11/16" Wrench

1/2", 9/16", & 11/16" Socket Wrench Tape Measure

Level

TOOLS REQUIRED

7/30/2012 Page 5 of 13


ULTRA SITE PRODUCT SPECIFICATIONS

338SH3-V46” SQUARE INGROUND MOUNT TABLE WITH 3 SEATS

Top & Seats: 11 gauge die formed angle frame 1”x1-7/8” with 3” radius corners. 3/4” #9 steel expanded metal. 7 gauge x 1-1/2” flat bar center support and mounting bracket understructure. Top is additionally diagonally supported to the corners with 7 gauge x 1-1/2” flat bar. Electrically MIG welded.

Coating: Oven fused functionalized polyethylene copolymer-based thermoplastic. Fluidized bed coating application with superior mechanical performance, impact resistance and UV-stability.

Frame: Main support column is 4”x4”x11 gauge pre-galvanized structural steel tubing. Arms are fabricated from 2-7/8” O.D. x 12 gauge pre-galvanized structural steel welded to 1/4” precision punched plates for attachment to the main column and 2”x2”x3/16” structural steel angle for lateral seat support. Seat attachment points are 10 gauge precision punched tabs. Table top attachment structure is fabricated from 2”x2”x3/16” structural steel angle and top attachment points are 7 gauge x 1-1/2” steel flat bar.

Frame Coating: Electrostatic powder coated application oven cured.

Hardware: All stainless steel hardware fasteners.

Dimensions: Top is 46” square x 30-1/4” high. Seats are 12” wide x 36” long x 18” high. Outside to outside dimensions of 3 seat table is 76-1/2”X 61-1/4”.

7/30/2012 Page 6 of 13

9611

3

4

10

12

214

13

7

1

5

8

ITEM NO. PartNo DESCRIPTION QTY1 T-V46-T 46" Expanded Square Top 12 P-V338-ARM 338 vinyl arm 3

3 P-338S or G-338S 338 IG post asem 1

4 P-01-04-0150 H Bracket 15 T-V36-S 3' Expanded Seat 36 33-02-0007 5/16" Flat Washer (SS) 327 33-02-0004 7/16" SS Washer 168 33-02-0008 3/8" Flat Washer (SS) 49 33-05-0029 5/16" x 1" Machine Bolt (SS) 16

10 33-06-0049 7/16" x 5-1/2" Machine Bolt 811 33-03-0012 5/16" Kep Nut (SS) 1612 33-01-0006 7/16" Hex Nut (SS) 813 33-01-0018 3/8" Hex Nut (SS) 414 33-06-0042 3/8" x 1" Carriage Bolt (SS) 4


COMPONENTS

7/30/2012 Page 7 of 13

3

2

10

7

12

Attach the 338 Vinyl Arms to the 338 Post using specified hardware.

ITEM NO. PartNo DESCRIPTION step 1 sh3v/QTY.1 T-V46-T 46" Expanded Square Top 12 P-V338-ARM 338 vinyl arm 33 P-338S or G-338S 338 IG post asem 14 P-01-04-0150 H Bracket 15 T-V36-S 3' Expanded Seat 36 33-02-0007 5/16" Flat Washer (SS) 327 33-02-0004 7/16" SS Washer 168 33-02-0008 3/8" Flat Washer (SS) 49 33-05-0029 5/16" x 1" Machine Bolt (SS) 1610 33-06-0049 7/16" x 5-1/2" Machine Bolt 811 33-03-0012 5/16" Kep Nut (SS) 1612 33-01-0006 7/16" Hex Nut (SS) 813 33-01-0018 3/8" Hex Nut (SS) 414 33-06-0042 3/8" x 1" Carriage Bolt (SS) 4


STEP 1

7/30/2012 Page 8 of 13

14

13

4

8

Attach the H Bracket to the 338 Post using specified hardware.

ITEM NO. PART NUMBER DESCRIPTION step 2 sh3v/QTY.1 46_SQ-asem 46" Expanded Square Top 12 VIN_ARM-asem 338 vinyl arm 33 338_post 338 IG post asem 14 H frame asem H Bracket 15 seat_asem 3' Expanded Seat 36 5-16 SS 5/16" Flat Washer (SS) 327 7-16 SS 7/16" SS Washer 168 3-8 SS 3/8" Flat Washer (SS) 49 HBOLT 0.3125-18x1x1-N 5/16" x 1" Machine Bolt (SS) 1610 HBOLT 0.4375-14x5.5x1.125-C 7/16" x 5-1/2" Machine Bolt 811 5-16 kep nut (ss) 5/16" Kep Nut (SS) 1612 Hex_Nut3 7/16" Hex Nut (SS) 813 HNUT 0.3750-16-D-C 3/8" Hex Nut (SS) 414 Carriage_Bolt 3/8" x 1" Carriage Bolt (SS) 4


STEP 2

7/30/2012 Page 9 of 13

11 69

1

Attach the 46" Square Top to the H Bracket using specified hardware.

ITEM NO. PartNo DESCRIPTION step 3 sh3v/QTY.1 T-V46-T 46" Expanded Square Top 12 P-V338-ARM 338 vinyl arm 33 P-338S or G-338S 338 IG post asem 14 P-01-04-0150 H Bracket 15 T-V36-S 3' Expanded Seat 36 33-02-0007 5/16" Flat Washer (SS) 327 33-02-0004 7/16" SS Washer 168 33-02-0008 3/8" Flat Washer (SS) 49 33-05-0029 5/16" x 1" Machine Bolt (SS) 1610 33-06-0049 7/16" x 5-1/2" Machine Bolt 811 33-03-0012 5/16" Kep Nut (SS) 1612 33-01-0006 7/16" Hex Nut (SS) 813 33-01-0018 3/8" Hex Nut (SS) 414 33-06-0042 3/8" x 1" Carriage Bolt (SS) 4


STEP 3

7/30/2012 Page 10 of 13

9 611

5

Attach the 3' Seats to the 338 Vinyl Arms using specified hardware.

ITEM NO. PART NUMBER DESCRIPTION step 4 sh3v/QTY.1 46_SQ-asem 46" Expanded Square Top 12 VIN_ARM-asem 338 vinyl arm 33 338_post 338 IG post asem 14 H frame asem H Bracket 15 seat_asem 3' Expanded Seat 36 5-16 SS 5/16" Flat Washer (SS) 327 7-16 SS 7/16" SS Washer 168 3-8 SS 3/8" Flat Washer (SS) 49 HBOLT 0.3125-18x1x1-N 5/16" x 1" Machine Bolt (SS) 1610 HBOLT 0.4375-14x5.5x1.125-C 7/16" x 5-1/2" Machine Bolt 811 5-16 kep nut (ss) 5/16" Kep Nut (SS) 1612 Hex_Nut3 7/16" Hex Nut (SS) 813 HNUT 0.3750-16-D-C 3/8" Hex Nut (SS) 414 Carriage_Bolt 3/8" x 1" Carriage Bolt (SS) 4


STEP 4

7/30/2012 Page 11 of 13

30"

18"

18"

18"

Estimated Required Concrete: 12 - 50 lb Bags of Concrete Mix


FOOTINGS

7/30/2012 Page 12 of 13

48 1/4" 17 7/8"

30 1/4"

GroundLevel

36"

61 5/16"

12"

46"

76 5/8"


OVERALL DIMENSIONS

7/30/2012 Page 13 of 13

Proposal #:

Date:

Bill To: Ship To: From:

RANTZ / PURCHASING

Account #: 235495 Sean Quintal

OUHSD Phone: 805-312-0422

309 S K ST Fax: 805-830-0445

OXNARD, CA 93030-5299 [email protected]

Phone: Territory No: Southern California/Furniture & Equipment

Fax:

Email: [email protected]

Item # Qty Page Description List Price Your Price Amount

OUTDOOR ADA TABLES - DELIVERED

P338SH3-V 8 ULTRASITE 3-SEAT, 46" SINGLE PED, ADA SQUARE $1,599.00 $997.88 $7,983.04

TABLE, IN-GROUND, DIAMOND PATTERN

RED PLASTISOL WITH BLACK FRAME

YOUR PRICE INCLUDES FREE SHIPPING

PLEASE ADD YOUR SALES TAX TO PO

NIPA PIGGYBACK CONTRACT #R141608

You Saved: $4,808.96

Customer Phone 1-888-388-3224 $7,983.04

Service: FAX: 1-888-388-6344 $7,983.04

[email protected] PROPOSAL QUALIFICATIONS 1

PRICES FIRM TO: SHIPMENT BY: x FREE Shipping! (Delv'd Price) Installation:

9/5/2018 Best Way x Tailgate Delivery Only x by owner

SHIP BY: INVOICE TERMS: Lift Gate Truck Required by S.S.

ASAP Net 30 Inside Delivery _ other

x One Location

_ Multiple Locations

© 2015 School Specialty, Inc.

Title:

Page 1 of 1 Thank you for the opportunity to submit this proposal! Customer Copy

500 W BARD RD

OXNARD, CA 93033-6399

Phone:

Attn: JOSH BROWN

080618 Qty 8 46" Square ADA Picnic Tables

Please refer to this number when ordering

8/6/2018

Account #: 235605

HUENEME HS

Proposed By:

● THIS PROPOSAL AFFORDS SPECIAL ONE-TIME PRICING FOR THE PRODUCTS AND QUANTITIES LISTED

TOTAL All Pages

Page 1 TOTAL

Valid for 30 Days

● PRICES PROPOSED ARE ONLY VALID UNTIL THE EXPIRATION DATE SHOWN

Sean Quintal Category Sales Manager - F&E

● TO GUARANTEE PRICE(S) PROPOSED THIS FORM MUST ACCOMPANY YOUR ORDER

● IF ANY QUANTITIES ARE CHANGED, PRICES WILL BE SUBJECT TO RENEGOTIATION

mailto:[email protected]

(Page Two) Proposal #:

OUHSD


Page 2 TOTAL 0

NOTE: Please see page one of this proposal for qualification and conditions. © 2015 School Specialty, Inc.




(Page Three) Proposal #:

OUHSD


Page 3 TOTAL 0

NOTE: Please see page one of this proposal for qualification and conditions. © 2015 School Specialty, Inc.




Addendum #3_Cover_OUHSD-Track Replacement10 21 16 SOLID PLASTIC TOILET COMPARTMENTSAppendix A.doc338SH3-VCOVERDrawing View47WARRANTY AND TERMSSAFETY AND INSPECTIONHARDWAREDrawing View2Drawing View3Drawing View4Drawing View5Drawing View6Drawing View7Drawing View8Drawing View9Drawing View10TOOLS REQUIREDSPEC SHEETCOMPONENTSDrawing View48STEP 1Drawing View49STEP 2Drawing View50STEP 3Drawing View51STEP 4Drawing View52FOOTINGSDrawing View53Drawing View54OVERALL DIMENSIONSDrawing View55Drawing View56Drawing View57Drawing View58

080618 Qty 8 Outdoor ADA Tables Delivered Quote SQEZ

Oxnard Union High School District - PROJECT …...Oxnard Union High School District Project #...

Documents

Transcript of Oxnard Union High School District - PROJECT …...Oxnard Union High School District Project #...