OVERVIEW MECHANICAL PROPERTIES OF PRINTED TEST … · Innofil3D PRO 1 72,6 86,2 93,0 99,1 67,3 65,7...
2
OVERVIEW MECHANICAL PROPERTIES OF PRINTED TEST SPECIMENS This Comparison Data Sheet contains standardized material data for 3D-printed test specimens according to ISO 178, ISO 179 and ISO 527. For detailed information, see the Technical Data Sheets. TENSILE STRENGTH (MPa) (MPa) Innofil3D ABS Innofil3D PLA EPR InnoPET Innofil3D PRO 1 17,0 24,1 27,7 29,3 4,4 13,6 11,1 14,5 VERTICAL 50% INFILL HORIZONTAL TENSILE STRENGTH (MPa) (MPa) Innofil3D ABS Innofil3D PLA EPR InnoPET Innofil3D PRO 1 29,3 38,1 40,9 48,0 6,5 28,8 22,8 21,8 VERTICAL 100% INFILL 100% INFILL 100% INFILL HORIZONTAL FLEXURAL STRENGTH (MPa) (MPa) Innofil3D ABS Innofil3D PLA EPR InnoPET Innofil3D PRO 1 72,6 86,2 93,0 99,1 67,3 65,7 76,7 92,4 PARALLEL NORMAL Printing Temp. (°C) Heated Bed Temp. (°C) Print Speed (mm/s) 210 60 40 PLA 210 75 40 PET 210 60 40 PRO1 240 90 40 ABS CHARPY IMPACT STR. (kJ/m2) (kJ/m2) EPR InnoPET Innofil3D PLA Innofil3D PRO 1 Innofil3D ABS 5,2 14,2 18,8 39,3 12,4 13,1 20,4 35,4 NORMAL PARALLEL 35 30 25 20 15 10 5 0 Innofil3D PLA EPR InnoPET Innofil3D PRO 1 TENSILE STRENGTH RANKING OF PRINTED FILAMENTS ISO 527 test standard 50% infill TENSILE STRENGTH (MPa) Horizontal Vertical 60 50 40 30 20 10 0 Innofil3D ABS Innofil3D ABS Innofil3D PLA EPR InnoPET Innofil3D PRO 1 TENSILE STRENGTH RANKING OF PRINTED FILAMENTS ISO 527 test standard 100% infill TENSILE STRENGTH (MPa) Horizontal Vertical 120 100 80 60 40 20 0 Innofil3D PLA Innofil3D ABS EPR InnoPET Innofil3D PRO 1 Innofil3D PLA Innofil3D ABS EPR InnoPET Innofil3D PRO 1 FLEXURAL STRENGTH RANKING OF PRINTED FILAMENTS ISO 178 test standard 100% infill FLEXURAL STRENGTH (MPa) Normal Parallel Normal Parallel 45 40 35 30 25 20 15 10 5 0 CHARPY IMPACT STRENGTH RANKING OF PRINTED FILAMENTS ISO 179 test standard 100% infill CHARPY IMPACT STRENGTH (kJ/m2, unnotched) COMPARABLE DATA SHEET INNOFIL3D FILAMENTS ISO 527; Tensile Tests. A minimum of 5 specimens with 50% infill and a minimum of 5 specimens tested with 100% infill, printed both horizontally and vertically. ISO 178; Charpy Impact Tests. 10 specimens normal and 10 specimens parallel, all 100% infill. ISO 179; Flexural Tests. 10 specimens normal, 10 specimens parallel, all 100% infill. All test specimens were printed using an Ultimaker 2+ under the following conditions: The INNOFIL3D product data is provided in good faith and represents typical properties based on our current knowledge and experience, not to be construed as specification limits or minimum values. Product properties may be changed without notice. This document does not create any liability, warranty or guarantee of product performance. It is the buyer’s responsibility to determine the suitability of INNOFIL3D products for the intended application. 100% INFILL
Transcript of OVERVIEW MECHANICAL PROPERTIES OF PRINTED TEST … · Innofil3D PRO 1 72,6 86,2 93,0 99,1 67,3 65,7...
OVERVIEW MECHANICAL PROPERTIES OF PRINTED TEST SPECIMENS
This Comparison Data Sheet contains standardized material data for 3D-printed test specimens according to ISO 178, ISO 179 and ISO 527. For detailed information, see the Technical Data Sheets.
TENSILE STRENGTH (MPa) (MPa)
Innofil3D ABS
Innofil3D PLA
EPR InnoPET
Innofil3D PRO1
17,0
24,1
27,7
29,3
4,4
13,6
11,1
14,5
VERTICAL50% INFILL HORIZONTAL
TENSILE STRENGTH (MPa) (MPa)
Innofil3D ABS
Innofil3D PLA
EPR InnoPET
Innofil3D PRO1
29,3
38,1
40,9
48,0
6,5
28,8
22,8
21,8
VERTICAL100% INFILL
100% INFILL100% INFILL
HORIZONTAL
FLEXURAL STRENGTH (MPa) (MPa)
Innofil3D ABS
Innofil3D PLA
EPR InnoPET
Innofil3D PRO1
72,6
86,2
93,0
99,1
67,3
65,7
76,7
92,4
PARALLEL NORMAL
Printing Temp. (°C)
Heated Bed Temp. (°C)
Print Speed (mm/s)
210
60
40
PLA
210
75
40
PET
210
60
40
PRO1
240
90
40
ABS
CHARPY IMPACT STR. (kJ/m2) (kJ/m2)
EPR InnoPET
Innofil3D PLA
Innofil3D PRO1
Innofil3D ABS
5,2
14,2
18,8
39,3
12,4
13,1
20,4
35,4
NORMALPARALLEL
35
30
25
20
15
10
5
0Innofil3D
PLAEPR
InnoPETInnofil3D
PRO1
TENSILE STRENGTH RANKING OF PRINTED FILAMENTSISO 527 test standard50% infill
TEN
SIL
E S
TR
EN
GTH
(M
Pa)
Horizontal
Vertical
60
50
40
30
20
10
0Innofil3D
ABSInnofil3D
ABSInnofil3D
PLAEPR
InnoPETInnofil3D
PRO1
TENSILE STRENGTH RANKING OF PRINTED FILAMENTSISO 527 test standard100% infill
TEN
SIL
E S
TR
EN
GTH
(M
Pa)
Horizontal
Vertical
120
100
80
60
40
20
0Innofil3D
PLAInnofil3D
ABSEPR
InnoPETInnofil3D
PRO1Innofil3D
PLAInnofil3D
ABSEPR
InnoPETInnofil3D
PRO1
FLEXURAL STRENGTH RANKING OF PRINTED FILAMENTSISO 178 test standard100% infill
FLEX
UR
AL
STR
EN
GTH
(M
Pa)
Normal
Parallel
Normal
Parallel
45
40
35
30
25
20
15
10
5
0
CHARPY IMPACT STRENGTH RANKING OF PRINTED FILAMENTSISO 179 test standard100% infill
CH
AR
PY IM
PA
CT S
TR
EN
GTH
(kJ/
m2
, unnotc
hed)
COMPARABLE DATA SHEET
INNOFIL3D FILAMENTS
ISO 527; Tensile Tests. A minimum of 5 specimens with 50% infill and a minimum of 5 specimens tested with 100% infill, printed both horizontally and vertically.
ISO 178; Charpy Impact Tests. 10 specimens normal and 10 specimens parallel, all 100% infill.
ISO 179; Flexural Tests. 10 specimens normal, 10 specimens parallel, all 100% infill.
All test specimens were printed using an Ultimaker 2+ under the following conditions:
The INNOFIL3D product data is provided in good faith and represents typical properties based on our current knowledge and experience, not to be construed as specification limits or minimum values. Product properties may be changed without notice. This document does not create any liability, warranty or guarantee of product performance. It is the buyer’s responsibility to determine the suitability of INNOFIL3D products for the intended application.
100% INFILL
COMPARABLE DATA SHEET
INNOFIL3D F ILAMENTS
