Benefits of Including SAE Bolts, Nuts, and Washers in the ...
Ottoman · 2021. 4. 29. · Spring Washers and Flat Washers, tightening bolts only halfway. (See...
Transcript of Ottoman · 2021. 4. 29. · Spring Washers and Flat Washers, tightening bolts only halfway. (See...
Hardware List
Part List
6800-90
IMPORTANT
Carefully remove all the parts from the carton andplace them individually on a soft cloth to preventscratches or other damage.
Carefully and strictly follow these assembly instructionsto ensure a completed product as designed.
Do not use power tools above 8 volts to assemble.
Ottoman
D.Base1 pc.
F.Panel1 pc.
A.Cushion1 pc.
E.Foot4 pcs.
SmallHex Wrench1 pc.
Spring Washer22 pcs. (+1 extra)
M6x35Head Cap Bolt22 pcs. (+1 extra)
Hex Wrench1 pc. (+1 extra)
Flat Washer22 pcs. (+1 extra)
C.Panel2 pcs.
B.Panel2 pcs.
styles Customer Service: www.homestylesfurniture.com,home
[email protected], 888-680-7460
Assembly Instructions 2/6
IMPORTANT� Use a soft cloth between these parts and the floor.� Do not use power tools above 8 volts to assemble.� Do not tighten all the bolts until each part is properly assembled.� The unit must be level to work properly. Use the included adjustable levelers to level.� Keep Hex Wrench as the bolts may need to be tightened in the future.
STEP 1
Attach (D) to Panel (B) with Head Cap Bolts,BaseSpring Washers and Flat Washers,tightening bolts only halfway.(See Figure 1)
STEP 2
Attach Panel (C) to unit withHead Cap Bolts, Spring Washers and
Flat Washers, tightening bolts only halfway.
Figure 1
Head Cap Bolt
Spring Washer
Flat Washer
Flat Washer
Spring Washer
Head Cap Bolt
D
B
C
Assembly Instructions /3 6
STEP 3
Attach Panel (C) to unit with Head Cap Bolts,Spring Washers and Flat Washers, tightening bolts only halfway.
STEP 4
Insert Head Cap Bolts, Spring Washersand Flat Washers into unit, tightening bolts only halfway.
Flat Washer
Spring Washer
Head Cap Bolt
C
Head Cap Bolt
Spring Washer
Flat Washer
Assembly Instructions /4 6
STEP 5
Attach Panel (B) to unit with Head Cap Bolts,Spring Washers and Flat Washers, tightening bolts only halfway.
Head Cap Bolt
Spring Washer
Flat Washer
B
STEP 6
Insert Head Cap Bolts, Spring Washersand Flat Washers into unit, tightening bolts only halfway.
Tighten all bolts used in Steps 1, 2, 3, 4, 5 and 6.
Flat Washer
Spring Washer
Head Cap Bolt
Assembly Instructions /5 6
Head Cap Bolt
Spring Washer
Flat Washer
Velcro Strap Velcro Strap
E
E
E
STEP 7
Attach Feet (E) to unit with Head Cap Bolts,Spring Washers and Flat Washers.(See Figure 2)
STEP 8
Attach Panel (F) to Cushion (A) with velcro straps.(See Figure 3)
Figure 2
Figure 3
E
aaaaaa
aaaaaa
aaaaaaaaaaa
aaa
A
F
Assembly Instructions /6 6
A
STEP 9
Turn unit over to its upright position.
Place Cushion (A) into position.
Level unit by adjusting the adjustable levelers on bottom of unit.(See Figure 4) Figure 4
NEVERuse glass cleaners on
finished furniture. Ammoniachemically attacks the finish.
allow liquids to remain on furniture.Absorption causes parts to warp
and split and finishes to delaminate.
NEVER
CARE INSTRUCTIONS
Do not use rubberbased placemats.
PREVENTDISCOLORING
Do not use commercialwaxes and polishes.
PREVENTYELLOWING
Do not place hotobjects on surface.
PREVENTFINISH DAMAGE
Do not writedirectly on surface.
PREVENTMARKING
Do not use power toolsabove 8 volts to assemble.
PREVENTCRACKING
Do not placein direct sunlight.
PREVENTFADING
with a soft cloth moistenedin lukewarm soap and water.Buff with a dry clean cloth.
CLEAN
homestyles will provide replacements free of charge for missing or damaged parts within 1 year of purchase.Digital images of the defective parts may be required. If the product was not purchased from an authorized retailer,homestyles is under no obligation to provide replacement parts. Parts are not available for fully assembled items norare parts available for sale. Replacements for missing or damaged parts may be requested via contact info below.
styles Customer Service: www.homestylesfurniture.com,home
[email protected], 888-680-7460
Hardware List
Part List
6800-101
IMPORTANT
Carefully remove all the parts from the carton andplace them individually on a soft cloth to preventscratches or other damage.
Carefully and strictly follow these assembly instructionsto ensure a completed product as designed.
Do not use power tools above 8 volts to assemble.
Arm Chair
A.Back1 pc.
B.Seat1 pc.
C.Side2 pcs.
E.Foot4 pcs.
SmallHex Wrench1 pc.
Hex Wrench1 pc.
Spring Washer24 pcs. (+1 extra)
M6x35Head Cap Bolt24 pcs. (+1 extra)
Flat Washer24 pcs. (+1 extra)
Carton 6800-CUS is also need for assembly.
styles Customer Service: www.homestylesfurniture.com,home
[email protected], 888-680-7460
Assembly Instructions 2/5
IMPORTANT� Use a soft cloth between these parts and the floor.� Do not use power tools above 8 volts to assemble.� Do not tighten all the bolts until each part is properly assembled.� The unit must be level to work properly. Use the included adjustable levelers to level.� Keep Hex Wrench as the bolts may need to be tightened in the future.
STEP 1
Attach Seat (B) to Back (A) with Head Cap Bolts,Spring Washers and Flat Washers,tightening bolts only halfway.(See Figure 1)
STEP 2
Attach to Side (C) withunitHead Cap Bolts, Spring Washers and
Flat Washers, tightening bolts only halfway.(See Figure 2)
Flat Washer
Spring Washer
Head Cap Bolt
Head Cap Bolt
Spring Washer
Flat Washer
B
A
Figure 1
C
Figure 2
Assembly Instructions 3/5
STEP 4
Attach unit to Side (C) withHead Cap Bolts, Spring Washers and
Flat Washers, tightening bolts only halfway.
STEP 3
Insert Head Cap Bolts, Spring Washersand Flat Washers into unit, tightening boltsonly halfway.(See Figure 3)
Head Cap Bolt
Spring Washer
Flat Washer
C
Figure 3
Head Cap Bolt
Spring Washer
Flat Washer
Assembly Instructions /4 5
STEP 5
Insert Head Cap Bolts,Spring Washers and Flat Washers
into unit, tightening bolts only halfway.
Tighten all bolts used in Steps 1, 2, 3, 4 and 5.
STEP 6
Attach Feet (E) to unit withHead Cap Bolts, Spring Washersand Flat Washers.(See Figure 4)
Head Cap Bolt
Spring Washer
Flat Washer
Head Cap Bolt
Spring Washer
Flat Washer
Figure 4
E
E
E
E
Assembly Instructions /5 5
STEP 7
Turn over unit to its upright position.
Attach Seat Cushion (F) to unit by pushing toggles through weaving in back of unit.(See Figure 5)
Place Back Cushion (G) into position.
Level unit by adjusting the adjustable levelers on bottom of unit.(See Figure 6)
Figure 5
Toggle
F
Figure 6
GToggle
NEVERuse glass cleaners on
finished furniture. Ammoniachemically attacks the finish.
allow liquids to remain on furniture.Absorption causes parts to warp
and split and finishes to delaminate.
NEVER
CARE INSTRUCTIONS
Do not use rubberbased placemats.
PREVENTDISCOLORING
Do not use commercialwaxes and polishes.
PREVENTYELLOWING
Do not place hotobjects on surface.
PREVENTFINISH DAMAGE
Do not writedirectly on surface.
PREVENTMARKING
Do not use power toolsabove 8 volts to assemble.
PREVENTCRACKING
Do not placein direct sunlight.
PREVENTFADING
with a soft cloth moistenedin lukewarm soap and water.Buff with a dry clean cloth.
CLEAN
homestyles will provide replacements free of charge for missing or damaged parts within 1 year of purchase.Digital images of the defective parts may be required. If the product was not purchased from an authorized retailer,homestyles is under no obligation to provide replacement parts. Parts are not available for fully assembled items norare parts available for sale. Replacements for missing or damaged parts may be requested via contact info below.
styles Customer Service: www.homestylesfurniture.com,home
[email protected], 888-680-7460
Hardware List
Part List
IMPORTANT
Carefully remove all the parts from the carton andplace them individually on a soft cloth to preventscratches or other damage.
Carefully and strictly follow these assembly instructionsto ensure a completed product as designed.
Do not use power tools above 8 volts to assemble.
6800-58
Seating
D.Frame2 pcs.
E.Foot4 pcs.
SmallHex Wrench1 pc.
Hex Wrench1 pc.
Spring Washer20 pcs. (+1 extra)
M6x35Head Cap Bolt20 pcs. (+1 extra)
Flat Washer20 pcs. (+1 extra)
J.Clip2 pcs.
styles Customer Service: www.homestylesfurniture.com,home
[email protected], 888-680-7460
O.Back1 pc.
P.Seat1 pc.
Assembly Instructions 2/5
IMPORTANT� Use a soft cloth between these parts and the floor.� Do not use power tools above 8 volts to assemble.� Do not tighten all the bolts until each part is properly assembled.� The unit must be level to work properly. Use the included adjustable levelers to level.� Keep Hex Wrench as the bolts may need to be tightened in the future.
Figure 1
Middle Unit
STEP 1
Attach Seat (P) to Back (O) with Head Cap Bolts,Spring Washers and Flat Washers,tightening bolts only halfway.(See Figure 1)
STEP 2
Attach Frame (D) to unit withHead Cap Bolts, Spring Washers and
Flat Washers, tightening bolts only halfway.
Flat Washer
Spring Washer
Head Cap Bolt
P
O
Flat Washer
Spring Washer
Head Cap Bolt
D
Assembly Instructions /3 5
STEP 3
Attach withFrame (D) to unitHead Cap Bolts, Spring Washers andFlat Washers, tightening bolts only halfway.
Tighten all bolts used in Steps 1, 2 and 3.
STEP 4
Attach Feet (E) to unit with Head Cap Bolts,Spring Washers and Flat Washers.
(See Figure 2)
Figure 2
D
Flat Washer
Spring Washer
Head Cap Bolt
Head Cap Bolt
Spring Washer
Flat Washer
E
EE
E
Assembly Instructions /4 5
Sofa
STEP 5
Attach left unit, middle unit and right unit with Clips (J).(See Figure 3)
Figure 3
J
J
J
J
Left Unit Middle Unit Right Unit
For a sofa, follow instructions in 6800-57 carton, then complete Steps 5 and 6.
For a 5, 6 or 7 seat sectional, follow instructions in 6800-401 and 6800-402 cartons.
Assembly Instructions /5 5
STEP 6
6800-CUS cartons are also needed for this step.Three
Turn unit to its upright position.
Attach Seat Cushions (F) to unit by pushing toggles through weaving in back of unit.(See Figure 4)
Place Back Cushions (G) into position.
Level unit by adjusting the adjustable levelers on bottom of unit.(See Figure 5)
Figure 5
Figure 4
ToggleGG
G
FF
F
Toggle
NEVERuse glass cleaners on
finished furniture. Ammoniachemically attacks the finish.
allow liquids to remain on furniture.Absorption causes parts to warp
and split and finishes to delaminate.
NEVER
CARE INSTRUCTIONS
Do not use rubberbased placemats.
PREVENTDISCOLORING
Do not use commercialwaxes and polishes.
PREVENTYELLOWING
Do not place hotobjects on surface.
PREVENTFINISH DAMAGE
Do not writedirectly on surface.
PREVENTMARKING
Do not use power toolsabove 8 volts to assemble.
PREVENTCRACKING
Do not placein direct sunlight.
PREVENTFADING
with a soft cloth moistenedin lukewarm soap and water.Buff with a dry clean cloth.
CLEAN
homestyles will provide replacements free of charge for missing or damaged parts within 1 year of purchase.Digital images of the defective parts may be required. If the product was not purchased from an authorized retailer,homestyles is under no obligation to provide replacement parts. Parts are not available for fully assembled items norare parts available for sale. Replacements for missing or damaged parts may be requested via contact info below.
styles Customer Service: www.homestylesfurniture.com,home
[email protected], 888-680-7460
Hardware List
Part List
IMPORTANT
Carefully remove all the parts from the carton andplace them individually on a soft cloth to preventscratches or other damage.
Carefully and strictly follow these assembly instructionsto ensure a completed product as designed.
Do not use power tools above 8 volts to assemble.
6800-401
Sectional
A.Back2 pcs.
O.Back1 pc.
D.Frame4 pcs.
B.Seat2 pcs.
P.Seat1 pc.
C.Side2 pcs.
E.Foot12 pcs.
SmallHex Wrench1 pc.
Hex Wrench1 pc.
Spring Washer64 pcs. (+1 extra)
M6x35Head Cap Bolt64 pcs. (+1 extra)
Flat Washer64 pcs. (+1 extra)
styles Customer Service: www.homestylesfurniture.com,home
[email protected], 888-680-7460
Assembly Instructions 2/7
IMPORTANT� Use a soft cloth between these parts and the floor.� Do not use power tools above 8 volts to assemble.� Do not tighten all the bolts until each part is properly assembled.� The unit must be level to work properly. Use the included adjustable levelers to level.� Keep Hex Wrench as the bolts may need to be tightened in the future.
STEP 2
Attach to Side (C) withunitHead Cap Bolts, Spring Washers and
Flat Washers, tightening bolts only halfway.(See Figure 2)
Flat Washer
Spring Washer
Head Cap Bolt
Head Cap Bolt
Spring Washer
Flat Washer
Figure 1
C
Left Unit
STEP 1
Attach Seat (B) to Back (A) with Head Cap Bolts,Spring Washers and Flat Washers,tightening bolts only halfway.(See Figure 1)
Figure 2
A
B
Assembly Instructions /3 7
STEP 3
Attach withFrame (D) to unitHead Cap Bolts, Spring Washers andFlat Washers, tightening bolts only halfway.
Tighten all bolts used in Steps 1, 2 and 3.
STEP 4
Attach Feet (E) to unitwith Head Cap Bolts,
Spring Washers and Flat Washers.(See Figure 3)
Figure 3
Flat Washer
Spring Washer
Head Cap Bolt
Head Cap Bolt
Spring Washer
Flat Washer
E
E
E
E
D
Assembly Instructions /4 7
Right Unit
STEP 5
Attach Seat (B) to Back (A) with Head Cap Bolts,Spring Washers and Flat Washers,tightening bolts only halfway.
STEP 6
Attach to Side (C) withunitHead Cap Bolts, Spring Washers and
Flat Washers, tightening bolts only halfway.
Flat Washer
Spring Washer
Head Cap Bolt
A
B
Head Cap Bolt
Spring Washer
Flat Washer
C
Assembly Instructions /5 7
STEP 7
Attach withFrame (D) to unitHead Cap Bolts, Spring Washers andFlat Washers, tightening bolts only halfway.
Tighten all bolts used in Steps , 6 and 7.5
STEP 8
Attach Feet (E) to unitwith Head Cap Bolts,
Spring Washers and Flat Washers.
Flat Washer
Spring Washer
Head Cap Bolt
D
Head Cap Bolt
Spring Washer
Flat Washer
E
E
E
E
Assembly Instructions /6 7
Middle Unit
STEP 9
Attach Seat (P) to Back (O) with Head Cap Bolts,Spring Washers and Flat Washers,tightening bolts only halfway.
STEP 10
Attach Frame (D) to unit withHead Cap Bolts, Spring Washers and
Flat Washers, tightening bolts only halfway.
Flat Washer
Spring Washer
Head Cap Bolt
Flat Washer
Spring Washer
Head Cap Bolt
P
O
D
Assembly Instructions /7 7
STEP 11
Attach withFrame (D) to unitHead Cap Bolts, Spring Washers andFlat Washers, tightening bolts only halfway.
Tighten all bolts used in Steps 9, 10 and 11.
Flat Washer
Spring Washer
Head Cap Bolt
STEP 12
Attach Feet (E) to unitwith Head Cap Bolts,
Spring Washers and Flat Washers.
EE
E
E
Head Cap Bolt
Spring Washer
Flat Washer
To complete assembly, follow instructions in 6800-402 carton.
D
NEVERuse glass cleaners on
finished furniture. Ammoniachemically attacks the finish.
allow liquids to remain on furniture.Absorption causes parts to warp
and split and finishes to delaminate.
NEVER
CARE INSTRUCTIONS
Do not use rubberbased placemats.
PREVENTDISCOLORING
Do not use commercialwaxes and polishes.
PREVENTYELLOWING
Do not place hotobjects on surface.
PREVENTFINISH DAMAGE
Do not writedirectly on surface.
PREVENTMARKING
Do not use power toolsabove 8 volts to assemble.
PREVENTCRACKING
Do not placein direct sunlight.
PREVENTFADING
with a soft cloth moistenedin lukewarm soap and water.Buff with a dry clean cloth.
CLEAN
homestyles will provide replacements free of charge for missing or damaged parts within 1 year of purchase.Digital images of the defective parts may be required. If the product was not purchased from an authorized retailer,homestyles is under no obligation to provide replacement parts. Parts are not available for fully assembled items norare parts available for sale. Replacements for missing or damaged parts may be requested via contact info below.
styles Customer Service: www.homestylesfurniture.com,home
[email protected], 888-680-7460
Hardware List
Part List
IMPORTANT
Carefully remove all the parts from the carton andplace them individually on a soft cloth to preventscratches or other damage.
Carefully and strictly follow these assembly instructionsto ensure a completed product as designed.
Do not use power tools above 8 volts to assemble.
6800-402
Sectional
Cartons 6800-401 and 6800-CUS3 are also needed for assembly.
L.Back1 pc.
H.Seat Cushion1 pc.
M.Seat1 pc.
I.Back Cushion1 pc.
K.Back Cushion1 pc.
N.Back1 pc.
E.Foot4 pcs.
J.Clip6 pcs.
SmallHex Wrench1 pc.
Hex Wrench1 pc.
Spring Washer18 pcs. (+1 extra)
M6x35Head Cap Bolt18 pcs. (+1 extra)
Flat Washer18 pcs. (+1 extra)
styles Customer Service: www.homestylesfurniture.com,home
[email protected], 888-680-7460
Assembly Instructions 2/7
IMPORTANT� Use a soft cloth between these parts and the floor.� Do not use power tools above 8 volts to assemble.� Do not tighten all the bolts until each part is properly assembled.� The unit must be level to work properly. Use the included adjustable levelers to level.� Keep Hex Wrench as the bolts may need to be tightened in the future.
Follow instructions in 6800-401 carton first, then proceed with Step 13.
Corner Unit
STEP 13
Attach Seat (M) to Back (N) with Head Cap Bolts,Spring Washers and Flat Washers,tightening bolts only halfway.
STEP 14
Attach Back (L) to unit withHead Cap Bolts, Spring Washers
and Flat Washers, tightening bolts only halfway.
Head Cap Bolt
Spring Washer
Flat Washer
Head Cap Bolt
Spring Washer
Flat Washer
M
N
L
Assembly Instructions /3 7
STEP 15
Insert Head Cap Bolts, Spring Washersand Flat Washers into unit, tightening boltsonly halfway.
Tighten all bolts used in Steps 13, 14 and 15.
STEP 16
Attach Feet (E) to unitwith Head Cap Bolts,
Spring Washers and Flat Washers.
Head Cap Bolt
Spring Washer
Flat Washer
Head Cap Bolt
Spring Washer
Flat Washer
E
E
E
E
For a 4 seat sectional, complete Steps 17 and 18.
For a 5 seat sectional, follow instructions in 6800-58 carton, then complete Steps 19 and 20.
For a 6 seat sectional, follow instructions in 2 6800-58 cartons, then complete Steps 21 and 22.
For a 7 seat sectional, follow instructions in 3 6800-58 cartons, then complete Steps 23 and 24.
Assembly Instructions /4 7
4 Seat Sectional
STEP 17
Attach left unit, middle unit, corner unitand right unit with Clips (J).(See Figure 4)
Right Unit
Left Unit Middle Unit
Corner Unit
STEP 18
Turn unit to its upright position.
Attach Seat Cushions (F) to unit bypushing toggles through weaving in back of unit.
(See Figure 5)
Place Seat Cushion (H) and Back Cushions (I), (K) into position.
Level unit by adjusting the adjustable levelers on bottom of unit.(See Figure 6)Figure 6
FF F
GG
G
H
J
J
J
J
J J
I
Figure 4
Figure 5
Toggle
K
Assembly Instructions /5 7
5 Seat Sectional
STEP 19
Attach left unit, middle units, corner unitand right unit with Clips (J).(See Figure 7)
Right Unit
Middle Unit
Left Unit Middle Unit
Corner Unit
STEP 20
6800-CUS carton is also needed for this step.
Turn unit to its upright position.
Attach Seat Cushions (F) to unit bypushing toggles through weaving in back of unit.
(See Figure 8)
Place Seat Cushion (H) and Back Cushions (I), (K) into position.
Level unit by adjusting the adjustable levelers on bottom of unit.(See Figure 9)Figure 9
J
J
J
J
J
J
J
J
GG G
G
H
Figure 7
FF F
F
I
Figure 8
Toggle
K
Assembly Instructions /6 7
6 Seat Sectional
STEP 21
Attach left unit, middle units, corner unitand right unit with Clips (J).(See Figure 10)
Figure 10Corner Unit
STEP 22
6800-CUS cartons are also needed for this step.Two
Turn unit to its upright position.
Attach Seat Cushions (F) to unit bypushing toggles through weaving in back of unit.
(See Figure 11)
Place Seat Cushion (H) and Back Cushions (I), (K) into position.
Level unit by adjusting the adjustable levelers on bottom of unit.(See Figure 12)Figure 12
JJ
JJ
JJ
J
J
JJ
Right Unit
Middle Unit
Left Unit Middle Unit Middle Unit
GG G
GG
H
FF
F FF
I
Figure 11
Toggle
K
Assembly Instructions /7 7
7 Seat Sectional
STEP 23
Attach left unit, middle units, corner unitand right unit with Clips (J).(See Figure 13)
STEP 24
6800-CUS cartons are also needed for this step.Three
Turn unit to its upright position.
Attach Seat Cushions (F) to unit bypushing toggles through weaving in back of unit.
(See Figure 14)
Place Seat Cushion (H) and Back Cushions (I), (K) into position.
Level unit by adjusting the adjustable levelers on bottom of unit.(See Figure 15)Figure 15
Figure 14
Toggle
JJ
J
JJ
J
J
J
J
J
J
J
Corner Unit
Right Unit
Middle Unit
Middle Unit
Left Unit Middle Unit Middle Unit
Figure 13
G G G GG
GH
I
FF F F
FF
K
NEVERuse glass cleaners on
finished furniture. Ammoniachemically attacks the finish.
allow liquids to remain on furniture.Absorption causes parts to warp
and split and finishes to delaminate.
NEVER
CARE INSTRUCTIONS
Do not use rubberbased placemats.
PREVENTDISCOLORING
Do not use commercialwaxes and polishes.
PREVENTYELLOWING
Do not place hotobjects on surface.
PREVENTFINISH DAMAGE
Do not writedirectly on surface.
PREVENTMARKING
Do not use power toolsabove 8 volts to assemble.
PREVENTCRACKING
Do not placein direct sunlight.
PREVENTFADING
with a soft cloth moistenedin lukewarm soap and water.Buff with a dry clean cloth.
CLEAN
homestyles will provide replacements free of charge for missing or damaged parts within 1 year of purchase.Digital images of the defective parts may be required. If the product was not purchased from an authorized retailer,homestyles is under no obligation to provide replacement parts. Parts are not available for fully assembled items norare parts available for sale. Replacements for missing or damaged parts may be requested via contact info below.
styles Customer Service: www.homestylesfurniture.com,home
[email protected], 888-680-7460
Part List
6800-CUS3
IMPORTANT
Carefully remove all the parts from the carton andplace them individually on a soft cloth to preventscratches or other damage.
Carefully and strictly follow these assembly instructionsto ensure a completed product as designed.
Cushions
F.Seat Cushion3 pcs.
G.Back Cushion3 pcs.
For assembly see instructions in carton 6800-402.
Care Instructions
� Keep cushions free of natural debris.� Tip and angle cushions after use.� Store cushions inside when not in use.� Allow a minimum of 24 hours for wet cushions to air dry.� Never use a hairdryer on cushions.� Never put cushions in a clothes dryer.
styles Customer Service: www.homestylesfurniture.com,home
[email protected], 888-680-7460
Part List
IMPORTANT
Carefully remove all the parts from the carton andplace them individually on a soft cloth to preventscratches or other damage.
Carefully and strictly follow these assembly instructionsto ensure a completed product as designed.
Do not use power tools above 8 volts to assemble.
6801-57
Seating
A.Back1 pc.
D.Frame1 pcs.
B.Seat1 pc.
C.Side1 pc.
E.Foot4 pcs.
J.Clip1 pc.
Hardware List
6801-57 cartons are needed for assembly.Two
SmallHex Wrench1 pc.
Hex Wrench1 pc.
Spring Washer22 pcs. (+1 extra)
M6x35Head Cap Bolt22 pcs. (+1 extra)
Flat Washer22 pcs. (+1 extra)
styles Customer Service: www.homestylesfurniture.com,home
[email protected], 888-680-7460
Assembly Instructions 2/7
IMPORTANT� Use a soft cloth between these parts and the floor.� Do not use power tools above 8 volts to assemble.� Do not tighten all the bolts until each part is properly assembled.� The unit must be level to work properly. Use the included adjustable levelers to level.� Keep Hex Wrench as the bolts may need to be tightened in the future.
STEP 2
Attach to Side (C) withunitHead Cap Bolts, Spring Washers and
Flat Washers, tightening bolts only halfway.(See Figure 2)
Figure 1
Left Unit
STEP 1
Attach Seat (B) to Back (A) with Head Cap Bolts,Spring Washers and Flat Washers,tightening bolts only halfway.(See Figure 1)
Figure 2
Flat Washer
Spring Washer
Head Cap Bolt
A
B
Head Cap Bolt
Spring Washer
Flat Washer
C
Assembly Instructions /3 7
STEP 3
Attach withFrame (D) to unitHead Cap Bolts, Spring Washers andFlat Washers, tightening bolts only halfway.
Tighten all bolts used in Steps 1, 2 and 3.
STEP 4
Attach Feet (E) to unitwith Head Cap Bolts,
Spring Washers and Flat Washers.(See Figure 3)
Figure 3
Flat Washer
Spring Washer
Head Cap Bolt
Head Cap Bolt
Spring Washer
Flat Washer
E
E
E
E
D
Assembly Instructions /4 7
Right Unit
STEP 5
Attach Seat (B) to Back (A) with Head Cap Bolts,Spring Washers and Flat Washers,tightening bolts only halfway.
STEP 6
Attach to Side (C) withunitHead Cap Bolts, Spring Washers and
Flat Washers, tightening bolts only halfway.
Flat Washer
Spring Washer
Head Cap Bolt
A
B
Head Cap Bolt
Spring Washer
Flat Washer
C
Assembly Instructions /5 7
STEP 7
Attach withFrame (D) to unitHead Cap Bolts, Spring Washers andFlat Washers, tightening bolts only halfway.
Tighten all bolts used in Steps , 6 and 7.5
STEP 8
Attach Feet (E) to unitwith Head Cap Bolts,
Spring Washers and Flat Washers.
Flat Washer
Spring Washer
Head Cap Bolt
D
Head Cap Bolt
Spring Washer
Flat Washer
E
E
E
E
Assembly Instructions 6/7
Loveseat
STEP 9
Attach left unit and right unit with Clips (J).(See Figure 4)
Figure 4
J
J
Left Unit Right Unit
For a loveseat, complete Steps 9 and 10.
For a sofa, follow instructions in 6801-58 carton.
Assembly Instructions /7 7
STEP 10
Two 6801-CUS cartons are also needed for this step.
Turn unit to its upright position.
Attach Seat Cushions (F) to unit by pushing toggles through weaving in back of unit.(See Figure 5)
Place Back Cushions (G) into position.
Level unit by adjusting the adjustable levelers on bottom of unit.(See Figure 6)
Figure 6
Figure 5
Toggle
F
F
GG
Toggle
NEVERuse glass cleaners on
finished furniture. Ammoniachemically attacks the finish.
allow liquids to remain on furniture.Absorption causes parts to warp
and split and finishes to delaminate.
NEVER
CARE INSTRUCTIONS
Do not use rubberbased placemats.
PREVENTDISCOLORING
Do not use commercialwaxes and polishes.
PREVENTYELLOWING
Do not place hotobjects on surface.
PREVENTFINISH DAMAGE
Do not writedirectly on surface.
PREVENTMARKING
Do not use power toolsabove 8 volts to assemble.
PREVENTCRACKING
Do not placein direct sunlight.
PREVENTFADING
with a soft cloth moistenedin lukewarm soap and water.Buff with a dry clean cloth.
CLEAN
homestyles will provide replacements free of charge for missing or damaged parts within 1 year of purchase.Digital images of the defective parts may be required. If the product was not purchased from an authorized retailer,homestyles is under no obligation to provide replacement parts. Parts are not available for fully assembled items norare parts available for sale. Replacements for missing or damaged parts may be requested via contact info below.
styles Customer Service: www.homestylesfurniture.com,home
[email protected], 888-680-7460
Part List
6801-CUS
IMPORTANT
Carefully remove all the parts from the carton andplace them individually on a soft cloth to preventscratches or other damage.
Carefully and strictly follow these assembly instructionsto ensure a completed product as designed.
Cushions
F.Seat Cushion1 pc.
G.Back Cushion1 pc.
For assembly see instructions in carton 6801-57, 6801-58, 6801-101 or 6801-402.
Care Instructions
� Keep cushions free of natural debris.� Tip and angle cushions after use.� Store cushions inside when not in use.� Allow a minimum of 24 hours for wet cushions to air dry.� Never use a hairdryer on cushions.� Never put cushions in a clothes dryer.
styles Customer Service: www.homestylesfurniture.com,home
[email protected], 888-680-7460
Hardware List
Part List
6800-20
IMPORTANT
Carefully remove all the parts from the carton andplace them individually on a soft cloth to preventscratches or other damage.
Carefully and strictly follow these assembly instructionsto ensure a completed product as designed.
Do not use power tools above 8 volts to assemble.
End Table
D.Base1 pc.
A.Top1 pc.
E.Foot4 pcs.
SmallHex Wrench1 pc.
Spring Washer20 pcs. (+1 extra)
M6x35Head Cap Bolt20 pcs. (+1 extra)
Hex Wrench1 pc. (+1 extra)
Flat Washer20 pcs. (+1 extra)
C.Panel2 pcs.
B.Panel2 pcs.
styles Customer Service: www.homestylesfurniture.com,home
[email protected], 888-680-7460
Assembly Instructions 2/5
IMPORTANT� Use a soft cloth between these parts and the floor.� Do not use power tools above 8 volts to assemble.� Do not tighten all the bolts until each part is properly assembled.� The unit must be level to work properly. Use the included adjustable levelers to level.� Keep Hex Wrench as the bolts may need to be tightened in the future.
STEP 1
Attach (D) to Panel (B) with Head Cap Bolts,BaseSpring Washers and Flat Washers,tightening bolts only halfway.(See Figure 1)
STEP 2
Attach Panel (C) to unit withHead Cap Bolts, Spring Washers and
Flat Washers, tightening bolts only halfway.
Figure 1
B
C
Flat Washer
Spring Washer
Head Cap Bolt
Head Cap Bolt
Spring Washer
Flat Washer
D
Assembly Instructions /3 5
B
STEP 3
Attach Panel (B) to unit with Head Cap Bolts,Spring Washers and Flat Washers, tightening bolts only halfway.
Head Cap Bolt
Spring Washer
Flat Washer
STEP 4
Insert Head Cap Bolts, Spring Washersand Flat Washers into unit, tightening bolts only halfway.
Flat Washer
Spring Washer
Head Cap Bolt
Assembly Instructions /4 5
C
STEP 5
Attach Panel (C) to unit withHead Cap Bolts, Spring Washersand Flat Washers,tightening bolts only halfway.
Tighten all bolts used inSteps 1, 2, 3, 4 and 5.
Head Cap Bolt
Spring Washer
Flat Washer
Head Cap Bolt
Spring Washer
Flat Washer
E
E
E
E
STEP 6
Attach Feet (E) to unit with Head Cap Bolts,Spring Washers and Flat Washers.
(See Figure 2)
Figure 2
Assembly Instructions /5 5
STEP 7
Turn over unit to its upright position.
Place (A) into position.Top
Level unit by adjusting the adjustable levelers on bottom of unit.(See Figure 3) Figure 3
A
NEVERuse glass cleaners on
finished furniture. Ammoniachemically attacks the finish.
allow liquids to remain on furniture.Absorption causes parts to warp
and split and finishes to delaminate.
NEVER
CARE INSTRUCTIONS
Do not use rubberbased placemats.
PREVENTDISCOLORING
Do not use commercialwaxes and polishes.
PREVENTYELLOWING
Do not place hotobjects on surface.
PREVENTFINISH DAMAGE
Do not writedirectly on surface.
PREVENTMARKING
Do not use power toolsabove 8 volts to assemble.
PREVENTCRACKING
Do not placein direct sunlight.
PREVENTFADING
with a soft cloth moistenedin lukewarm soap and water.Buff with a dry clean cloth.
CLEAN
homestyles will provide replacements free of charge for missing or damaged parts within 1 year of purchase.Digital images of the defective parts may be required. If the product was not purchased from an authorized retailer,homestyles is under no obligation to provide replacement parts. Parts are not available for fully assembled items norare parts available for sale. Replacements for missing or damaged parts may be requested via contact info below.
styles Customer Service: www.homestylesfurniture.com,home
[email protected], 888-680-7460