OTHER EQUIPMENTS · Copper (Cu) with range 0.1 ppm to 1.0 ppm Fourier Transform Spec-troscopy...
2
For additional information about Material Characterization Laboratory, its services or any other related matter please contact : ABOUT US The Material Characterizaon Laboratory is a tesng laboratory that specializes in physical and chemical characterizaon. This laboratory is also used for ECH 3903 (Material Characterizaon Laboratory) undergraduate course. On 19 May 2015, this lab has been accredited with MS ISO/IEC 17025 (SAMM No. 711) for two analycal services under the cluster of chemical and physical. Two instruments were cerfied in this accreditaon, namely the Differenal Scanning Calorimetry (DSC) and Atomic Absorpon Spectroscopy (AAS). Material Characterizaon Laboratory Department of Chemical and Environmental Engineering, Faculty of Engineering, Universi Putra Malaysia, 43400 UPM Serdang, Selangor, Malaysia. Tel: +603-89471595 Fax: +603-86567120 E-mail: [email protected] OTHER EQUIPMENTS TGA BET GC (FID) DMA SEM- EDX HPLC (UV) FTIR ICP-OES HPLC (RI) PSA UV-VIS SPECTRO GC (TCD) CHNS MATERIAL CHARACTERIZATION LABORATORY (MCL) Department of Chemical and Environmental Engineering
Transcript of OTHER EQUIPMENTS · Copper (Cu) with range 0.1 ppm to 1.0 ppm Fourier Transform Spec-troscopy...
For additional information about Material Characterization
Laboratory, its services or any other related matter please contact :
ABOUT US
The Material Characterization Laboratory is a
testing laboratory that specializes in physical and
chemical characterization. This laboratory is also
used for ECH 3903 (Material Characterization
Laboratory) undergraduate course. On 19 May
2015, this lab has been accredited with MS ISO/IEC
17025 (SAMM No. 711) for two analytical services
under the cluster of chemical and physical. Two
instruments were certified in this accreditation,
namely the Differential Scanning Calorimetry (DSC)
and Atomic Absorption Spectroscopy (AAS).
Material Characterization Laboratory Department of Chemical and Environmental
Engineering, Faculty of Engineering, Universiti Putra Malaysia,
43400 UPM Serdang, Selangor, Malaysia. Tel: +603-89471595 Fax: +603-86567120
E-mail: [email protected]
OTHER EQUIPMENTS
TGA BET
GC (FID)
DMA
SEM-
EDX
HPLC (UV)
FTIR
ICP-OES
HPLC (RI)
PSA
UV-VIS
SPECTRO
GC (TCD)
CHNS
MATERIAL CHARACTERIZATION LABORATORY (MCL)
Department of Chemical and
Environmental Engineering
Microsoft
Surface Water Elemental
Analysis
The determination of elemental concentration by using Flame Atomic Absorption Spectrometry (AAS) at parts per million (ppm) level. The elements are:
Nickel (Ni) with range 0.03-0.3 ppm
Zinc (Zn) with range 0.1 ppm to 1.0 ppm
Copper (Cu) with range 0.1 ppm to 1.0 ppm
Environmental Quality Act 1974:
We offer to you the surface water elemental testing for this type of surface water:
Reservoir
Wetland
River
Lake
Pond
Waste Water
* No sample treatment service provided
Accepted Sample Criteria:
Clear Surface Water Sample
Minimum volume 10mL
Standard is provided
Equipment Rate (RM/unit)
CHN-S Analyser 350/sample
Dynamic Mechanical Analyser (DMA)
150/sample
Inductively Coupled Plasma (ICP-OES)
100 (fixed cost) and 50/element/sample
Brunauer-Emmett-Teller (BET) Analyser
500/sample
High Performance Liquid Chromatography (HPLC)
UV/RI Detector
150 (fixed cost) & 50 for subsequent injection
UV-Visible Spectropho-tometer (UV-Vis)
50/hour
Thermo Gravimetric Analysis (TGA)
150/hr/sample and 100/hr for subsequent
hr
Fourier Transform Spec-troscopy (FTIR)
100/sample
Gas Chromatography (GC)- FID/TCD
150 (1st injection) and 50/injection for subse-
quent injection
Scanning Electron Micro-scope (SEM)
180/sample
Energy-dispersive X-ray spectroscopy (EDX)
150/sample
Particle Size Analyzer (PSA)
30/sample
Other Testing Services:
Glass Transition (Tg)
Determination Analysis
TESTING ARE BASED ON ASTM E 1356-98
& ASTM E 967-03
Accepted Sample Criteria:
Amorphous region from 30 to 300°C
Sample weight: 5 to 20mg
Example of sample: polymeric material and mixture plastic, fibres and adhesive
We offer to you the Glass Transition (Tg) determination testing for amorphous materials, partially Crystalline materials using Differential Scanning Calorimetry (DSC).
TESTING ARE BASED ON APHA 3111B
Contact Persons: 1. Madam Nor Hasni Zahari
(03-89464435/[email protected]) 2. Madam Shafizah Masuri
(03-89471595/[email protected])
RM 50 per
sample/element
RM 150/hr/sample &
RM100/hr for subsequent hr
MS 1SO/IEC 17025
TESTING
SAMM NO. 711
MS 1SO/IEC 17025
TESTING
SAMM NO. 711
Parameter Unit Standards
A B
Cu mg/l 0.20 1.0
Ni mg/l 0.20 1.0
Zn mg/l 1.0 1.0
