NSLC Reference # CN-39-FY21 Addendum # 5 NSLC BERWICK RENOVATION Approved for Alternate · 2021. 1....

N O V A S C O T I A L I Q U O R C O R P O R A T I O N

93 Chain Lake Drive, Halifax, Nova Scotia, Canada B3S 1A3 • Tel: (902) 450-NSLC • www.myNSLC.com

NSLC Reference # CN-39-FY21 January 7, 2021 Addendum # 5

Nova Scotia Liquor Corporation Addendum # 5

NSLC BERWICK RENOVATION

Please note the following modifications to the Specifications. Compliant bids shall be deemed to include these modificiations. Please also note the listed alternate approvals:

Approved for Alternate:

Anotec Series 21 and 22 Insuldoor – D01 & D02 Anotec Series 21 and 22 door – D05 & D06 Anotec Series 3400 – (2.5” x 3.625” main frame) curtain wall – GL-01, GL-02 & GL-03

Section 12 48 40 Entrance mats – Helix Z1 and Z2, (carpet insert) by ConstructionSpecialties is acceptable given it can be used in the orientation given for each plan. If the manufacturer does not recommend installation in the orientation and footprint for a specific store then the product cannot be accepted for that store.

CGC Inc. Acoustic Ceiling Tile

Sikafloor Morritex Trowel System

Hadrian Metal Lockers

Aluminum curtain walls, doors & Stanley sliders equivalent to the alumicor 2600 and Kawneer 1600UT

Clarifications:

Door Schedule - D04 is confirmed as an Anthony model Vista C Series Ceiling demolition - Ceiling grid to be demolished and a new one installed A102 note regarding end panels – bidders are advised that the panels are shipped from Owner’s furniture manufacturer and tile is to be installed on the end panels.



PT08 and PT09 on the finish plan should be PT-6 and PT-7 respectively

Allow for access to coolers, office areas and warehouse areas at all times. The intention for this note is that:

• Store is to be open throughout renovation• Staff needs access to all backshop areas at all times, including the

cooler. They can’t be hoarded. Work in these areas needs to happenaround regular store operations and/or before open hours. Coolerdoesn’t have to be accessible to public at all times.

• Retail isn’t mentioned because we don’t want to make people thinkthat retail area work has to happen while that area is open. Hoardingcan happen within retail, but as much retail as possible should be keptopen for business throughout construction.

There’s a general guideline on how to section off the store in tender drawing on drawing A002 R1 (addendum 1). It’s just a rough outline that might work; we are open to suggestions.

Prelimnary project schedule should reflect work days and should not account for any weather delays or interruptions due to Covid 19.

Section 10 01 00 2.1 LOCKERS

• Provide four double tier lockers (8 doors total)• Two coat hooks to be provided to each compartment• Height of locker between 60-72”

One existing bollard was missing from existing elevations. Bollard to be scraped and repainted yellow

Electrical panel change over work to be scheduled around store hours to minimize downtime. Work can start on Saturday evening and continue to Monday Morning. Store could potentially be closed early / open late to accommodate. NSLC will carry only the extra cost associated with after hours / weekend work by Berwick Power, to be billed as a separate line item by



Berwick Power to the GC. All other costs associated with the change over, including the base cost of the change over work by Berwick Power, is to be built into the bid.

Office exterior wall demolition work to start after all materials are onsite. Wall is to be weather tight at the end of each working day. For security reasons, the demolition and reconstruction of this section is to be completed as quickly as possible, ideally within one day. NSLC will provide security forces if needed.

Demolition drawing noted that roller racks in cooler is to remain. Roller racks to be removed and reinstalled by client’s forces for epoxy floor installation by GC.

New Floor shelving end panels (by client’s forces) to receive tile (by GC). Size of each end panel is as follows

Minimize floor tile demolition during store open hours due to health and noise concerns.

Q&A:

Please note the following are enquiries received by the NSLC and our response to the bidders. This Q&A is shared for information purposes to ensure full transparency.

1. Q: Demolition drawing indicates ceiling grid to remain, remove all tile(Grid to be painted). RCP labels it as new grid and tile. Please clarify. – A: demolish existing grid. install new.

2. Q: A-102 Note for “backing and Tile on end panels; ensure flush finishw/frame. Fully adhere stainless steel base to eliminate gap at base of end panel”; is there a detail for this work? A: The end panels are shipped from VIC the furniture manufacturer, tile is installed to end panels.

3. Q: May the Cart Corral be custom made through a local fabricator, orthrough McCue per section 10? A: Yes

4. Q: Items noted as “SN” in plans and elevations are supplied and installedby owner? (assuming this is signage?) A: SN are included in scope and are signs. Refer to A-900 schedule and plan for placement and details on each item.



5. Q: A4/A202 Acrylic Panels identified. Is there any information on thisproduct? A: clear acrylic panels installed over cooler walls. contractor's choice in supplier

6. Q: PT08 and PT09 are not called up on this finish planA: Use PT-6 and PT-7

7. Q: Is there to be subway tiles at the ends of shelving?A: The tile trim is to be applied to outside corners of the cool zone wall. For clarifity, the trim is White Jolly. The subway tile should be installed to the end of gondola shelving, please can refer to CT-1 on A-002 schedule notes as well as A-104 plan.

8. Q: What is going on stairs to office?A: Stair finishes to remain.

9. Q: Does porcelain tile go in to office steps or stop at door of office?A: The porcelain tile going into the office should not stop at the door, but be laid to the base of the stairs.

10. Q: Does the 3x6 subway tile have to be Dal wall tile if they are brightwhite? A: Alternate wall tiles are considered, please provide more information/sample for approval.

11. Q: Who will be responsible for removing any furniture or stock that maybe required to move for work access? A: NSLC is responsible for removal of stock and furniture in advance of the work.

12. Q: On the plan page M100, it calls for removal of both grilles in thevestibule, page M200 says to install new R-2 grilles, the existing grille closest to the office is actually a force flow heater, is this to remain? A: The two existing ceiling mounted grilles in the Vestibule will remain. Both grilles to be removed, cleaned, and re-installed in the existing frames.

13. Q: There is not an R-2 grille on the schedule, plan calls for two to beinstalled in vestibule, existing grilles are different sizes due to one being a heater grille. What are sizes required? A: New R-2 grilles are no longer required.

14. Q: What is model of existing AHU? Need info to size curb adapter for newunit? A: Existing roof curb to be dimensioned onsite prior to ordering new transition curb. Existing unit is YORK model D3CE076A25BDB (see attached photo).



Thank you,

Tracey Darrigan, Procurement Manager



NSLC Reference # CN-39-FY21 December 22, 2020 Addendum # 4



Please note the following modifications to the Bid Instructions. Compliant bids shall be deemed to include these modificiations.

Closing Date

Closing date for this tender has been extended to the following:

Wednesday, January 13, 2021 2:00 PM AST (Halifax local time)

Site Visit

6. SITE MEETINGNon-mandatory site meetings will be held on Tuesday, January 5th, 2020. Interested bidders shall schedule 30-minute time slots for the visit, beginning at 7:30am and ending 9:30am on that day.

Due to COVID provincial regulations regarding gathering size, no more than 4 bidders can participate in the meeting at one time. Therefore, bidders may only have one person representing their company. To schedule a site visit, bidders should email Tracey Darrigan, Procurement Manager, NSLC ([email protected]) to make an appointment.

Attendees must maintain 6 foot separation from each other and wear appropriate PPE.

NSLC will bear no responsibility or liability for inadequate PPE or best practices not being followed.

Thank you,


mailto:[email protected]






Please note the following modifications to the specifications. Compliant bids shall be deemed to include these modifications.

Specifications:

Please add the following electrical specification sections for Division 26:

1. 26 05 00 Electrical General Requirements2. 26 05 20 Wire and Box Connectors (0 – 1000V)3. 26 05 21 Wires and Cables (0 – 1000V)4. 26 05 28 Grounding – Secondary5. 26 05 29 Fastenings and Supports6. 26 05 31 Splitters, Junction Pull Boxes and Cabinets7. 26 05 32 Outlet Boxes, Conduit Boxes and Fittings8. 26 05 34 Conduits, Conduit Fastenings and Fittings9. 26 24 17 Panelboards Breaker Type10. 26 27 26 Wiring Devices11. 26 28 21 Moulded Case Circuit Breakers12. 26 28 23 Disconnect Switches - Fused and Non-Fused13. 26 29 10 Motor Starters to 600V14. 26 50 00 Lighting Equipment15. 26 50 05 Lighting Control System16. 26 52 01 Equipment for Emergency Lighting17. 26 53 00 Exit Lights

Thank you,


NSLC Select Store Roll-Out Section 26 05 00 NSL-057 Berwick – November 2020 ELECTRICAL GENERAL REQUIREMENTS Page 1 of 11

PART 1 - GENERAL

1.1 GENERAL

.1 This Section covers items common to Sections of Divisions 26. This section supplements requirements of Division 01.

1.2 CODES AND STANDARDS

.1 Do complete installation in accordance with 2018 Canadian Electric Code (CEC), and local regulations, except where specified otherwise.

.2 Do overhead systems in accordance with CAN/CSA-C22.3 No. 1 and underground systems in accordance with CAN/CSA C22.3 No. 7, except where specified otherwise.

.3 Comply with the requirements of the National Energy Code of Canada for Buildings 2015.

1.3 CARE, OPERATION AND START-UP

.1 Instruct the Consultant and operating personnel in the operation, care and maintenance of all equipment.

.2 Arrange and pay for services of manufacturer's factory service engineer to supervise start-up of installation, check, adjust, balance and calibrate components.

.3 Provide these services for such period, and for as many visits as necessary to put equipment in operation, and ensure that operating personnel are conversant with all aspects of its care and operation.

1.4 VOLTAGE RATINGS

.1 Operating voltages: to CSA-C235.

.2 Motors, electric heating, control and distribution devices and equipment to operate satisfactorily at 60 Hz within normal operating limits established by above standard. Equipment to operate in extreme operating conditions established in above standard without damage to equipment.

1.5 PERMITS, FEES AND INSPECTION

.1 Submit to the Electrical Inspection Department, Municipal Authority and supply authority the necessary number of drawings and specifications, for examination and approval prior to commencement of work. Submit information within twenty (20) working days of the award of Tender and provide the Consultant with written notice at the time this has been submitted.

.2 Provide the Consultant with a copy of the electrical Inspection Department and supply Authority Plans Review Report, immediately upon receipt. No shop drawings will be reviewed prior to receipt of the Plans Review Report from the Contractor.


.3 Obtain all necessary permits including an Electrical Wiring Permit for electrical work and Communications Cabling Permit for communications cabling work from the authority having jurisdiction, prior to commencement of work. Provide a copy of each permit to the Consultant upon receipt. Display permits on the work site.

.4 Upon specific request, the Consultant will provide, to the Contractor, up to a maximum of three (3) copies of the drawings and specifications required for submittal to the Electrical Inspection Department and Supply Authority. These drawings and specifications will be provided to the Contractor at no cost, unless specified otherwise.

.5 Arrange for all required inspections to be conducted by the authority having jurisdiction. Provide a copy of all inspection reports to the Consultant immediately upon receipt. Notify the Consultant immediately of changes required by the authority having jurisdiction.

.6 Furnish Certificates of Acceptance from authorities having jurisdiction upon completion of work. Include a copy in the Operation and Maintenance Manual.

.7 Pay all associated fees.

1.6 MATERIALS AND EQUIPMENT

.1 Provide materials and equipment in accordance with Section 01 61 00.

.2 Equipment and material to be CSA certified. Where there is no alternative to supplying equipment, which is not CSA certified, obtain special approval from the authority having jurisdiction.

.3 Factory assemble control panels and component assemblies.

.4 The equipment listed on the project equipment schedules and shown on the drawings is the "basis of design equipment", the Contractor may utilize the alternates listed in the project documents or submit alternates for approval to this equipment that meet the technical and quality requirements of the project specifications. If there are necessary changes to any building system to accommodate these alternates, coordinate changes and provide at no additional cost to the Contract.

1.7 FINISHES

.1 Shop finish metal enclosure surfaces by application of rust resistant primer inside and outside, and at least two (2) coats of finish enamel. .1 Paint outdoor electrical equipment "equipment green" finish to EEMAC Y1-1. .2 Paint indoor switchgear and distribution enclosures light grey to EEMAC 2Y-1.

.2 Clean and touch up surfaces of shop-painted equipment scratched or marred during shipment or installation, to match original paint.

.3 Clean and prime exposed non- galvanized hangers, racks and fastenings to prevent rusting.

1.8 EQUIPMENT IDENTIFICATION

.1 Identify electrical equipment with nameplates and labels as specified herein.


.2 Identification: .1 Provide switchboards, panels, disconnect switches, receptacles,

voice/data/CATV/Multimedia outlets, transformers, control panels, magnetic starters, TOL's, etc. with "lamicoid" nameplates as further described herein. Affix plates true and level, and plumb in all instances.

.2 Affix nameplates to all "metal" surfaces with steel type "pop- rivets".

.3 Affix nameplates to other types of surfaces with contact type cement.

.4 Affix nameplates to building "exterior" surfaces with nylon inserts and self-tapping screws unless specifically indicated otherwise.

.5 Apply contact type cement to complete rear side of plate, as opposed to several locations or areas on same.

.6 Lamicoid nameplates installed on distribution panelboards, motor control centres, splitter troughs and transformers to indicate the following: .1 Designated name of equipment. .2 Amperage of overcurrent protection device. .3 Voltages, number of phases and wires. .4 Designation of power source.

Example PANEL H - 150 AMPS 120/208V - 3PH - 4W FED FROM MAIN SWITCHBOARD #QMS-1

.7 Lamicoid nameplates installed on combination starters, magnetic starters, manual starter and all various systems controls, control panels, disconnect switches, etc., to contain the following information: .1 Designated name of equipment. .2 Designated name of power source. .3 Branch circuit breaker number(s) where possible. .4 Voltage(s). EXHAUST FAN NO. 5 SUPPLY FAN NO. 3 PANEL H - CCT. NO. 17 M.C.C. NO. 1 120V – PH 600V - 3 PH

.8 Lamicoid nameplates installed on fusible type disconnect switches are to also indicate maximum designated/designed fuse size.

.9 Install lamicoid nameplates on all junction and/or pull boxes sized 6” x 6” and larger indicating name of system, designated panel name and electrical characteristics where applicable.

.10 Install lamicoid nameplates adjacent to each overcurrent devices located in switchboards, CDP panels, etc. They need only indicate designated name and/or number of equipment they feed. Unused O.C. devices are to be identified as spare(s).

.11 Lamicoid nameplates installed on "main" service entrance switches, or "main" entrance switchboards to indicate the following information on minimum size 6” x 2” plate complete with two lines of ½” high lettering (Size #8 nameplate) Example: Example: MAIN BREAKER 800 AMPS MAIN SWITCH 200 AMPS 346/600V, 3PH, 4W 120/208V, 3PH, 4W

.12 Install an additional "lamicoid" nameplate on all, or any piece of electrical equipment, or apparatus (i.e., Main Switchboard, CDP panels, Panelboards, Motor Control Centres. etc.), that may contain overcurrent devices (i.e., circuit breakers and/or fuses), that have been designed for, and incorporate interrupting capacity sized "larger" than 10 KAIC.


Example: Min, interrupting capacity of breakers installed in this panel to be not less than 22 KAIC Example: Min. interrupting capacity of fuses installed in this MCC to be not less than 100 KAIC

.13 Install lamicoid nameplates above all types of receptacles and abutted directly to

tops of their respective device plates. Identification to indicate respective panel source complete with associated circuit breaker number(s) as per the following: .1 1/16” x ½” high complete with ¼” black letters on white core, directly

above all receptacles. Plate to be identical width as finish device plate. Example: PANEL H - 20

.14 Identify lamicoid nameplates above 120V receptacles protected by GFCI circuit breakers, or GFCI type receptacles as per the following: .1 1/16” thick x ¾” wide complete with ¼” black letters on white core above

all receptacles. Identical width as finish device plate (EXAMPLE: GFCI Protected Panel H-26).

.15 Apply lamicoid nameplate(s) for power/voice/data/CATV/CCTV/multimedia outlets above face of finish plate, complete with information as specified in section 27 05 13. .1 1/16” thick x ¾” wide complete with ¼” black letters on white cove above

all receptacles. Identical width as finish device plate. .16 All addressable fire alarm devices are to be lamicoid identified.

.1 Chain-hang lamicoid identification on mechanical items (pressure switches, supervisory switches, etc.).

.2 Manual pull station lamicoid plate to be similar to typical receptacle lamicoid plate.

.3 Lamicoid wording to match physical location and annunciator display address.

.17 Lamicoid 1/8” thick plastic engraving sheet, white face, black core, for all electrical systems except fire alarm which shall have red face with white core. .1 1/16” thick nameplates above receptacles as previously indicated, with

top left and right corners to be rounded off. .2 Lettering on lamicoid nameplates must not start, nor end nearer than ½”

from either, or both ends of said plates. Size of lettering, including overall lengths of various plates will be as indicated in the following chart:

NAMEPLATE SIZES Size 1 1/3 x 2” 1 line ¼” high letters Size 2 ½” x 3” 1 line ¼” high letters Size 3 2/3” x 3” 2 lines ¼” high letters Size 4 ¾” x 3-3/4” 1 line 1/3” high letters Size 5 ¼” x 3-3/4” 2 lines ½” high letters Size 6 1” x 4” 1 line ½’ high letters Size 7 1” x 4” 2 lines ¼” high letters Size 8 2” x 6” 2 lines ½” high letters

.3 Have wording on nameplates and labels approved by the Consultant prior to manufacture.

.4 Allow for average of forty (40) letters per nameplate and label.


.5 Identification to be English.

.6 Provide and install lamicoid nameplates on, or adjacent to, all various systems' control panels and/or cabinets complete with information as indicated. Nameplates to reflect individual system's assigned name, and where applicable, also indicate both designated panel name and associated branch circuit breaker number(s). .1 Energy management panels .2 Low voltage lighting relay panels (EXAMPLE: LIGHTING RELAY PANEL #1 -

LPA - 36).

.7 Junction and pull boxes: indicate system and voltage.

.8 Co-ordinate names of equipment and systems with other trades such that equipment identification is consistent.

.9 In addition to required nameplates and colour coding, junction boxes to have the panel and circuit numbers of all wiring contained within listed on the coverplate. Write list neatly written using black indelible marker.

.10 Colour code electrical junction boxes, pull boxes, and conduit fittings as follows: .1 Above accessible ceilings:

.1 Apply colour coding prior to installation of boxes/equipment.

.2 Where primary colour only is indicated: .1 Colour inside and outside of box. .2 Colour all cover plates.

.3 Where primary and secondary colours are indicated: .1 Paint inside and outside of box with the primary colour. .2 Diagonally apply to each half of the cover plate the primary and

secondary colours. .2 In areas with open ceilings:

.1 Apply colour coding prior to installation of boxes/equipment.

.2 Where primary colour only is indicated: .1 Colour inside of box.

.3 Where primary and secondary colours are indicated: .1 Diagonally apply to each half of the inside of the box the primary

and secondary colours.

.11 Where a lamicoid identified item is installed above an accessible ceiling, provide two (2) lamicoid plates, one (1) at the item location and one (1) directly below on the underside of the ceiling.

1.9 WIRING IDENTIFICATION

.1 Identify wiring with self-laminating, permanently mechanically imprinted labels on both ends of each conductor and cable utilized. Identify conductors and cables in each junction or pull box through which they pass. Install labels in a "flagged" manner around individual conductors.

.2 Maintain phase sequence and colour coding throughout.

.3 All conductors are to have their insulation colours identified as follows: Phase A - Red Phase B - Black

NSLC Select Store Roll-Out Section 26 05 00 NSL-057 Berwick – November 2020 ELECTRICAL GENERAL REQUIREMENTS Page 6 of 11 Phase C - Blue Neutral - White Bond - Green Ground - Green Isolated Ground - Green c/w yellow strip

.4 Colour coded "Conductor Insulation" as per the following: .1 All sizes of phase conductors up to and including #2AWG. .2 All sizes of neutral, bond and/or ground conductors up to and including

#3/0AWG. .3 Approved coloured tapes in lieu of insulation colouring may be used to identify

conductors that exceed sizes as previously indicated. Label at both ends of all runs at a minimum of 12” from terminations, in addition to within all boxes between both ends of the run.

.5 Use colour coded wires in communication cables, matched throughout system.

.6 Indicate panel and circuit number of all phase conductors i.e.: "Panel "A" - cct 3". Identify all neutral conductors bonding and ground conductors to indicate the phase conductor with which they are associated.

1.10 CONDUIT AND CABLE IDENTIFICATION

.1 Colour code conduits, boxes and metallic sheathed cables. Colour boxes inside and outside where one colour is required above accessible ceilings only. Boxes are to be coloured on inside only where two colours are required. Metal cover plates are to have both colours applied diagonally where two colours are required. Paint entire cover plate where one colour is required.

.2 Colour code conduits, boxes, and metallic sheathed cables. .1 Above accessible ceilings, colour boxes inside and outside where one colour is

required. Colour boxes on inside only where two colours are required. Metal cover plates are to have both colours applied diagonally where two colours are required. Paint entire cover plate where one colour is required.

.2 In areas with exposed ceilings, colour boxes inside only where one (1) or two (2) colours are required. Paint metal cover plates to match architectural finish in area.

.3 Code with paint at points where conduit or cable enters wall, ceiling, or floor, and at 50 foot intervals.

.3 Colours: 1” wide prime colour and ¾” wide auxiliary colour.

NSLC Select Store Roll-Out Section 26 05 00 NSL-057 Berwick – November 2020 ELECTRICAL GENERAL REQUIREMENTS Page 7 of 11 Primary Secondary System Colour Colour 0-50 volts VIOLET - 51 volts YELLOW - to 240 volts 241-600volts ORANGE - Fire alarm RED - Telephone BLACK - Voice only) Public Address BLUE - and Intercom Ground or Bond GREEN - Security BROWN - Mech. Controls RED WHITE Primary Secondary Cable Television YELLOW WHITE Computer (data BLACK WHITE only) Voice and Data BLUE WHITE

.4 All various system junction and/or pull boxes etc., where located above ceiling grid system, must have location identified on underside or room side of t-bar spline, with ¾” or ¼” on ¾” self-adhering colour coded circular shaped discs, affixed directly to spline in close proximity to where concealed box is located. Install same type of discs on ceiling or wall access cover plates. ¼” discs are all white in colour. Affix ¼” to center or middle of ¾” discs as system colours indicates.

Various Systems ¾” Discs ¼” Discs 0 to 50 volts VIOLET 51 to 240 volts YELLOW 241 to 600 volts ORANGE Fire Alarm RED Telephone (voice BLACK only) P.A. and Intercom BLUE Security BROWN Ground or Bond GREEN Cable Television YELLOW WHITE Energy Management RED WHITE Computer (data only) BLACK WHITE Voice and Data BLUE WHITE Other BROWN WHITE Other WHITE Other WHITE

.5 Provide a legend of colour coding, mounted under plexiglass cover. Install in main electrical room.

.6 Where boxes are not concealed, disks are to be fastened directly to outside of boxes after architectural painting is complete. Coverplates for such boxes are to have each branch circuit number neatly identified inside of the coverplate.

NSLC Select Store Roll-Out Section 26 05 00 NSL-057 Berwick – November 2020 ELECTRICAL GENERAL REQUIREMENTS Page 8 of 11 1.11 WIRING TERMINATIONS

.1 Lugs, terminals, screws used for termination of wiring to be suitable for either copper or aluminum conductors.

.2 Label all branch circuit wiring including phase conductors, neutral, ground and/or bonding conductors to be done on both ends of all circuit wires plus in any junction and pull boxes located between ends. Use write-on self-laminating labels. Wrap around conductor in a "U" fashion.

1.12 MANUFACTURERS AND CSA LABELS

.1 Visible and legible after equipment is installed.

1.13 WARNING SIGNS

.1 As specified and to meet requirements of Electrical Inspection Department and Consultant.

.2 Porcelain enamel decal signs, minimum size 7” x 10”.

1.14 SINGLE LINE ELECTRICAL DIAGRAMS

.1 Provide single line electrical diagrams under plexiglass as follows: .1 Electrical distribution system: locate in main electrical room. .2 Include a legend of colour coding for the various systems identified in item 10-

conduit and cable identification.

.2 Drawings: Full drawing size in main electrical.

1.15 LOCATION OF EQUIPMENT

.1 Do not install outlets back-to-back in wall; allow minimum 6” horizontal clearance between boxes. Do not install boxes back to back in the same stud space. .1 Provide under plexiglass in associated electrical and/or communications rooms.

.2 Change location of equipment at no extra cost or credit, providing distance does not exceed 10 feet, and information is given before installation.

.3 Locate light switches on latch side of doors.

1.16 MOUNTING HEIGHTS

.1 Mounting height of equipment is from finished floor to centre line of equipment unless specified or indicated otherwise.

.2 If mounting height of equipment is not specified or indicated, verify before proceeding with installation.

.3 Mounting heights for devices to conform to NBCC and NS Building Code regulations for Barrier Free design.


.4 Install electrical equipment at following heights unless otherwise indicated. .1 Local switches: 48” .2 Wall receptacles:

.1 General: 18”

.2 Above top of continuous baseboard heater: 8”, minimum 18” AFF.

.3 Above top of counters or counter backsplash: 6” .3 Panelboards: as required by Code or as indicated. .4 Wall mounted telephone, data and CATV outlets:

.1 General: 18”

.2 Above top of continuous baseboard heater: 8”, minimum 18” AFF.

.3 Above top of counters or counter backsplash: 6”

.4 In electrical rooms: 48”

1.17 LOAD BALANCE

.1 Measure phase current to panelboards with normal loads (lighting) operating at time of acceptance. Adjust branch circuit connections as required to obtain best balance of current between phases and record changes.

.2 Measure phase voltages at loads and adjust transformer taps to within 2% of rated voltage of equipment.

.3 Submit, at completion of Work, report listing phase and neutral currents on panelboards and dry-core transformers, operating under normal load. State hour and date on which each load was measured, and voltage at time of test.

1.18 CONDUIT AND CABLE INSTALLATION

.1 Install conduit and sleeves prior to pouring of concrete.

.2 If plastic sleeves are used in fire rated walls or floors, remove before conduit installation.

.3 Arrange and pay for holes through exterior walls and roof to be flashed and made weatherproof.

1.19 FIRESTOPPING

.1 Provide firestopping and smoke sealing of all cable, cable trough or conduit penetrations through fire resistant separations as specified in Section 07 84 00.

1.20 FIELD QUALITY CONTROL

.1 Conduct and pay for following tests: .1 Distribution system including phasing, voltage, grounding and load balancing. .2 Circuits originating from branch distribution panels. .3 Lighting and its control. .4 Motors, heaters and associated control equipment including sequenced

operation of systems where applicable. .5 Systems: lighting control system.

.2 Furnish manufacturer's certificate or letter confirming that entire installation as it pertains to each system has been installed to manufacturer's instructions.


.3 Insulation resistance testing: .1 Megger circuits, feeders and equipment up to 350 V with a 500 V instrument. .2 Megger 350-600 V circuits, feeders and equipment with a 1000 V instrument. .3 Check resistance to ground before energizing.

.4 Carry out tests in presence of the Consultant.

.5 Provide instruments, meters, equipment and personnel required to conduct tests during and at conclusion of project.

.6 Submit typed test results for the Consultant's review and inclusion in the Operation and Maintenance Manual.

1.21 COORDINATION OF PROTECTIVE DEVICES

.1 Confirm circuit protective devices such as overcurrent trips, relays and fuses are installed to required values and settings.

.2 Distribution equipment supplier to prepare a protection coordination study for all over current devices rated 200A and above. The study to indicate TCC and recommended breaker settings. Include Arc-Flash study for all electrical distribution equipment.

1.22 DEMONSTRATION, OPERATING AND MAINTENANCE INSTRUCTIONS

.1 Supply tools, equipment and personnel to demonstrate and instruct operating and maintenance personnel in operating, controlling, adjusting, troubleshooting and servicing all systems and equipment, during regular work hours, prior to acceptance.

.2 Use as-built drawings, operation and maintenance manual, audio visual aids, etc. as part of instruction materials.

.3 Allow for a minimum of two (2) eight (8)-hour working days to provide instruction and demonstration. This is in addition to training specified elsewhere.

1.23 WASTE MANAGEMENT AND DISPOSAL

.1 Collect, separate and recycle all site generated waste materials in accordance with Section 01 74 19 - Waste Management and Disposal.

.2 Confirm the following forms, included at the end of Section 01 74 19 - Waste Management and Disposal, are completed and submitted. .1 Waste Trip Log Form - Schedule A .2 Waste Tracking Summary - Schedule B

.3 Coordinate all Work related to Section 01 74 19 - Waste Management and Disposal.

1.24 COORDINATION UTILITIES

.1 Coordinate the installation and services of all necessary utility service providers, including but not necessarily limited to: .1 Electrical supply utility (NSP). .2 Communications service provider (Bell/Eastlink).


.2 Pay for all associated costs.

PART 2 - PRODUCTS

2.1 NOT USED

.1 Not applicable.

PART 3 - EXECUTION

3.1 NOT USED

.1 Not applicable.

END OF SECTION

NSLC Select Store Roll-Out Section 26 05 20 NSL-057 Berwick – November 2020 WIRE AND BOX CONNECTORS (0 – 1000V) Page 1 of 1

PART 1 - GENERAL

1.1 REFERENCES

.1 CSA C22.2 No. 65-2018, Wire Connectors.

PART 2 - PRODUCTS

2.1 MATERIALS

.1 Pressure type wire connectors with current carrying parts of copper sized to fit copper conductors as required. Provide for all panels including main switch board and main transformer.

.2 Spring type pressure wire connectors: with current carrying parts of copper and copper alloy sized to fit copper conductors 10 AWG or less. Provide connectors complete with appropriate size insulating cap.

.3 Clamps or connectors for armored cable, liquid tight flexible metal conduit.

.4 Bushing stud connectors are not acceptable.

PART 3 - EXECUTION

3.1 MATERIALS

.1 Make connections and terminations electrically and mechanically secure. Sizes of connectors to be as per manufacturer's recommendations for various sizes and combinations of wire sizes.

.2 Make joints required in branch wiring #10 and smaller utilizing spring type pressure wire connectors. Plier tighten wire connectors. Cap to completely fit or cover all enclosed conductors as required.

.3 Make joints for all other wiring utilizing colour keyed compression type connectors c/w compression tools. Apply an initial layer of compound type tape followed by an additional layer of vinyl tape. Approved alternative for wire connections up to, and including #6 may be colour coded wing-nut.

END OF SECTION

NSLC Select Store Roll-Out Section 26 05 21 NSL-057 Berwick – November 2020 WIRES AND CABLES (0 – 1000V) Page 1 of 4

PART 1 - GENERAL

1.1 REFERENCES

.1 CSA C22.2 No. 0.3-09(R2019), Test Methods for Electrical Wires and Cables.

1.2 RELATED WORK

.1 Submittal Procedures: Section 01 33 00

.2 Closeout Submittals: Section 01 78 00

.3 Electrical General Requirements: Section 26 05 00.

.4 Conduit, Conduit Fittings and Conduit Fastenings: Section 26 05 34

1.3 PRODUCT DATA

.1 Submit product data in accordance with Section 01 33 00 – Submittal Procedures.

1.4 OPERATION AND MAINTENANCE DATA

.1 Submit operation and maintenance data for incorporation into manual specified in Section 01 78 00 – Closeout Submittals.

PART 2 - PRODUCTS

2.1 BUILDING WIRES

.1 Conductors: to be soft drawn copper of 98% conductivity; stranded for 12 AWG and larger. Minimum size: 12 AWG.

.2 Copper conductors sized as indicated or as required by C.E.C., with 600 V insulation of chemically cross-linked thermosetting polyethylene material rated RW90-XLPE.

.3 Grounding and bonding conductors sized up to and including #10 AWG are to have green coloured RW90 cross linked insulation. Type TW75 green coloured insulation is acceptable for sizes #8 AWG and larger.

2.2 ARMOURED CABLES

.1 Conductors: insulated, copper, size as indicated, minimum #12 AWG.

.2 Type: AC90.

.3 Armour: interlocking type fabricated from aluminum strip.

.4 Connectors: designed for cable.


.5 Cable ties to Section 26 05 29 - Fastening and Supports. .1 ¼” dia threaded rods to support suspended channels.

2.3 CONTROL CABLES

.1 Type LVT: two (2) soft annealed copper conductors, sized as indicated, with thermoplastic insulation, outer covering of thermoplastic jacket.

.2 Control circuit wiring 50V and less: Cat 6a with yellow jacket.

PART 3 - EXECUTION

3.1 INSTALLATION OF BUILDING WIRES

.1 Install wiring as follows: .1 In conduit systems in accordance with Section 26 05 34.

3.2 INSTALLATION OF ARMOURED CABLES

.1 AC-90 will only be permitted for branch circuit wiring drops from ceiling junction boxes to light fixtures, within the same room requiring electrical power. The installation of AC-90 cable for branch circuit wiring home runs or runs between rooms is not acceptable.

.2 A home run is defined as that portion of the branch circuit wiring that runs between the applicable panelboard and the area or room in which it either: .1 Terminates at the applicable branch circuit device, or .2 Makes a splice for final connection to the applicable branch circuit device.

.3 The grouping together of AC-90 cables to form a "bundle" for securing purposes is acceptable provided: .1 In addition to securing AC-90 cables at 60" intervals to structure, tye-wrap multiple

or bundled groups of armoured cables together at mid-point between each structure support and secure to structure at 60" intervals, and also secure together between each structure support at 60" intervals.

.2 Limit grouping of AC-90 cables to a maximum of eight (8) current carrying conductors, including associated oversized neutrals, where phase sharing occurs.

.4 Install concealed, parallel and perpendicular to building lines and adequately secure to the building structure at not less than 60" intervals in such a manner as to confirm they are protected from potential types of mechanical damage occurring. Install independent supports for cabling in ceiling spaces, and do not use those of other trades. Do not secure cables to mechanical piping systems, ducts or suspended ceiling support wires. The laying of un-supported cables directly on the ceiling grid system is strictly prohibited.

.5 Always install and secure surface cables directly to the underside of ceiling slabs or metal decking where located in concealed ceiling spaces.

.6 The following examples incorporate uses of both common and dedicate branch circuit neutral conductors. .1 Maximum of two (2) runs of #12/4 conductor cables including common (oversized)

branch circuit neutrals in each. .2 Maximum of two (2) runs of #12/3 conductor cables, including oversized branch

circuit neutrals (if net 3 phase 3 wire) plus one (1) run of #12/2 cable.


.3 Maximum of four (4) runs of #12/2 conductor cables, each including a separate, dedicated branch circuit neutral conductor.

.7 Where dedicated or separate branch circuit neutral conductors are non-phase sharing they need not be sized larger than phase conductors they are accompanying unless specifically indicated otherwise.

.8 Originate AC-90 fixture feeds from the sides of outlet boxes and not from the box cover. Where three (3) and/or four (4) fixture drops extend from any one outlet box, the box shall not be sized smaller than 4-11/16" square.

.9 Fixture drop is defined as that portion of AC-90 cable or flexible conduit being used to make final connection between accessible type junction or outlet box located in ceiling space and its respective light fixture. .1 Fixture drops are not to exceed 15' in total length unless specifically indicated

otherwise. .2 There will not be more than four (4) drops permitted to be fed from any one box

regardless of its size. Secure AC-90 cables used for fixture drops within 12" of the junction box. Complete each light fixture with its own separate fixture drop originating from junction box located in the same room as the fixture. An exception will be made for recessed down lights which may be wired from one fixture to another if they have integral junction boxes and if the luminaire access opening is 6" or greater in diameter.

.3 Wire each light fixture with a separate "whip" emanating from an overhead junction box.

.4 Both #12 AWG and #14 AWG type AC-90 armoured cables may be used where the total fixture drop loads do not exceed the following: .1 5000W @347V, #12AWG .2 3500W @347V, #14AWG .3 1800W @120V, #12AWG .4 1300W @120V, #14AWG

.10 Provide separate pig-tail type leads in each light fixture junction/outlet box for final connection to fixture drops. These pig-tails are to be only connected to light fixture returns and associated neutral conductors.

3.3 INSTALLATION OF CONTROL CABLES

.1 Install control cables in E.M.T. complete with bonding conductor, minimum ¾” conduit and #14AWG bonding conductor.

.2 Bond control cable shield where required.

.3 Building management system controls wiring methods to be installed in accordance with Section 27 05 13 and 27 05 28 (per voice and data structured cabling).

3.4 INSTALLATION OF CABLES: GENERAL

.1 Support cables independently of supports used for equipment of other trades; do not support from or secure cables to ductwork, piping and ceiling hanger wires.

.2 Do not lay cables on top of suspended ceiling grids and tiles.


.3 Install cables in a neat and professional manner, so as to conserve headroom. Correct unacceptable Work at no additional cost to the Contract.

.4 Install cables parallel and perpendicular to building lines.

.5 Secure cables to underside of metal decking.

.6 Make tye-wrapping of the neutral conductor with its respective phase conductors at the closest point of entry within all panelboards, pull boxes, junction boxes and outlet boxes, etc.

.7 All branch circuits which do not have neutral conductors are to have their respective phase conductors tye-wrapped together.

.8 Twist stranded conductors together prior to any types of terminations taking place, but not necessarily limited to: receptacles, light switches, neutral terminal strips, bonding terminal strips, circuit breakers, disconnect switches, starters, contactors, relays, all types of termination lugs, panelboards, etc.

END OF SECTION

NSLC Select Store Roll-Out Section 26 05 28 NSL-057 Berwick – November 2020 GROUNDING - SECONDARY Page 1 of 3

PART 1 - GENERAL

1.1 RELATED SECTIONS

.1 Wires and Cables 0-1000V: Section 26 05 21

1.2 REFERENCES

.1 IEEE 837-2014, Qualifying Permanent Connections Used in Substation Grounding.

.2 CSA C22.2 No. 41-13(R2017), Grounding and Bonding Equipment.

PART 2 - PRODUCTS

2.1 EQUIPMENT

.1 Clamps for grounding of conductor: size as required and suitable for application.

.2 Insulated grounding and bonding conductors: soft drawn stranded copper of 98% conductivity, type RW90 (green coloured insulation as indicated in 26 05 00.

.3 Ground bus: copper, minimum size ¼” x 3” x 24” or as indicated, complete with insulated supports, fastenings, connectors.

.4 Ground connections to take place on the ground bus are to be as follows: .1 For wire sizes 6 AWG and smaller: copper, one-hole, short barrel (single crimp)

lugs. .2 Wire larger than 6 AWG to be two-hole, long barrel (dual crimp) lugs.

.5 Non-corroding accessories necessary for grounding system, type, size, material as indicated, including but not necessarily limited to: .1 Grounding and bonding bushings. .2 Protective type clamps. .3 Bolted type conductor connectors. .4 Thermit welded type conductor connectors. .5 Bonding jumpers, straps. .6 Pressure wire connectors.

.6 Copper compression type, long barrel, two-hole type lugs unless specified otherwise.

.7 Copper compression type connectors (cable to cable, cable to ground rod, etc.).

2.2 MANUFACTURERS

.1 Acceptable manufacturers: .1 FCI-Burndy Corporation .2 Erico Inc. .3 Thomas & Betts .4 Ilsco.

NSLC Select Store Roll-Out Section 26 05 28 NSL-057 Berwick – November 2020 GROUNDING - SECONDARY Page 2 of 3 PART 3 - EXECUTION

3.1 INSTALLATION GENERAL

.1 Install complete permanent, continuous grounding system including, electrodes, conductors, connectors, accessories. Conform to the requirements of the Consultant, applicable codes, and the local electrical inspection authority having jurisdiction.

.2 Install connectors in accordance with manufacturer's instructions.

.3 Protect exposed grounding and bonding conductors from mechanical injury.

.4 Use mechanical connectors for grounding and bonding connections to equipment provided with lugs, except for grounding terminations in 600V switchboards, 600V CDP panels, 600V MCC's. These are to be copper, compression type, long barrel, two-hole connectors.

.5 Soldered joints are not permitted.

.6 Install insulated bonding conductor in all conduits.

.7 Install separate insulated bonding conductor to outdoor lighting standards.

.8 Connect building structural steel to ground.

.9 Make grounding connections in radial configuration only, with connections terminating at single grounding point on street side of water pipe. Avoid loop connections.

.10 Bond single conductor, metallic armored cables to cabinet at supply end, and provide non-metallic entry plate at load end.

.11 Ground secondary service pedestals.

.12 Secure the 'feed' bonding conductor (wrapped around unbroken) to the grounding screw of each outlet/device box, before connecting to the other grounding conductors and/or providing a "pig-tail" lead for device terminations.

.13 Twist ground/bond wires together with a screw-on type wire connector, and then place in the rear of the outlet box.

.14 Bond EMT "wall stubs" or sleeves to ground as per CEC requirements.

.15 Bond conduits containing insulated ground conductor(s) at both ends.

.16 The bend radius of all grounding/bonding conductors to be a minimum of 200mm diameter.

3.2 SYSTEM AND CIRCUIT GROUNDING

.1 Install system and circuit grounding connections to neutral of secondary systems.

.2 Run the main incoming ground conductor unbroken to the main electrical service entrance overcurrent device ground bus and then to the wall mounted ground bus.

NSLC Select Store Roll-Out Section 26 05 28 NSL-057 Berwick – November 2020 GROUNDING - SECONDARY Page 3 of 3 3.3 EQUIPMENT GROUNDING

.1 Install grounding/bonding connections to typical equipment included in, but not necessarily limited to following list: service equipment, transformers, switchgear, duct systems, frames of motors, starters, control panels, building steel work, cellular floor headers, cells, fittings, distribution panels, outdoor lighting, metallic waste water piping systems, metallic rain water leader systems, metallic gas fuel piping systems.

3.4 GROUNDING BUS

.1 Install copper grounding bus mounted on insulated supports on wall of main electrical room.

.2 Ground items of electrical equipment to ground bus as indicated herein and on the Drawings.

3.5 COMMUNICATION SYSTEMS

.1 Telecommunications: provide grounding and bonding in accordance with BICSI Telecommunications Distribution Methods Manual (TDMM), 12th Edition.

.2 Provide one (1) green #6 AWG ground wire from main system ground to telecommunications rack in office.


.1 Perform tests in accordance with Section 26 05 00 - Electrical General Requirements.

.2 Perform ground continuity and resistance tests using method appropriate to site conditions and to approval of Consultant and local authority having jurisdiction over installation.

.3 Perform tests before energizing electrical system.

.4 Where applicable, disconnect ground fault indicator during tests.

END OF SECTION

NSLC Select Store Roll-Out Section 26 05 29 NSL-057 Berwick – November 2020 FASTENINGS AND SUPPORTS Page 1 of 2

PART 1 - GENERAL

1.1 NOT USED

.1 Not applicable.

PART 2 - PRODUCTS

2.1 SUPPORT CHANNELS

.1 U shape, size 1¾” x 1¾”, galvanized steel, surface mounted, suspended or set in poured concrete walls and ceilings unless otherwise indicated.

2.2 CABLE TIES

.1 Use cable ties solely for the purpose of holding cables in place when installed in cable tray.

.2 Nylon flame retardant, low smoke cable tie. Size as required.

.3 Nylon flame retardant, low smoke cable tie mounting bracket. Mechanical fastening type only; adhesive mounts not acceptable.

PART 3 - EXECUTION

3.1 INSTALLATION

.1 Secure equipment to solid masonry, tile and plaster surfaces with lead anchors or nylon shields.

.2 Secure equipment to poured concrete with expandable inserts.

.3 Secure equipment to hollow masonry walls or suspended ceilings with toggle bolts.

.4 Secure surface mounted equipment with twist clip fasteners to inverted T bar ceilings. Confirm T bars are adequately supported to carry weight of equipment specified before installation. Provide additional supports as necessary.

.5 Support equipment, conduit or cables using clips, spring loaded bolts, cable clamps designed as accessories to basic channel members.

.6 Fasten exposed conduit or cables within 3’ of each outlet box, junction box, pull box, cabinet or conduit fittings with spacing between supports as per CEC to building construction or support system using straps. .1 One-hole zinc plated steel straps to secure surface conduits and cables smaller

than 1½”. .2 Two-hole zinc plated steel straps for conduits and cables 1¾” and larger. .3 Beam clamps to secure conduit to exposed steel work.

.7 Suspended support systems:

NSLC Select Store Roll-Out Section 26 05 29 NSL-057 Berwick – November 2020 FASTENINGS AND SUPPORTS Page 2 of 2

.1 Support individual cable or conduit runs with 1/3” dia threaded rods and spring clips.

.2 Support two (2) or more cables or conduits on channels supported by 1/3” dia threaded rod hangers where direct fastening to building construction is impractical.

.8 For surface mounting of two (2) or more conduits use channels at 5 feet oc spacing.

.9 Provide metal brackets, frames, hangers, clamps and related types of support structures where indicated or as required to support conduit and cable runs.

.10 Confirm there is adequate support for raceways and cables dropped vertically to equipment where there is no wall support.

.11 Do not use wire lashing or perforated strap to support or secure raceways or cables.

.12 Do not use supports or equipment installed for other trades for conduit or cable support.

.13 Install fastenings and supports as required for each type of equipment, cables and conduits, and in accordance with manufacturer's installation recommendations.

.14 Fasten individual and multiple runs of armoured cables to structure and in bundles as permitted in 26 05 21 - Wire and Cables 0-1000 Volts.

.15 Support various suspended types of junction, pull and/or outlet boxes as well as conduits with minimum size 1/3” threaded rod, nuts and flat washers. Secure threaded rods to boxes with one flat washer and nut installed on both sides of box. .1 One (1) rod required for all type boxes sized 6” x 6” and smaller. .2 Two (2) rods required for boxes sized 36in3 and larger, up to and including those

sized 12” x 12”. .3 Minimum of four (4) rods required for all boxes sized larger than 144in3.

.16 Cut-off excess rod within ½” of channel bottom. In addition to C.E.C. minimum conduit spacing requirements, all suspended conduit runs containing horizontal or vertical elbows are to have one additional support rod installed not greater than 12” and midpoint of "all" 90 bends. Maximum spacings between conduit support channels will be as dictated by smallest size conduit(s) being supported and/or secured to same.

.17 In addition to the CEC minimum conduit spacing requirements, all suspended conduit runs containing horizontal or vertical elbows are to have one additional support rod installed not greater than 12” from midpoint of all 90° bends. Maximum spacings between conduit support channels will be dictated by smallest size conduit(s) being supported and/or secured to same.

END OF SECTION

NSLC Select Store Roll-Out Section 26 05 31 NSL-057 Berwick – November 2020 SPLITTERS, JUNCTION PULL BOXES AND CABINETS Page 1 of 2

PART 1 - GENERAL

1.1 SHOP DRAWINGS AND PRODUCT DATA

.1 Submit shop drawings and product data for cabinets in accordance with Section 01 33 00 – Submittal Procedures.

PART 2 - PRODUCTS

2.1 JUNCTION AND PULL BOXES

.1 Type C: welded steel construction, hinged cover, catch with hasp. Provision for locking. Surface mounting.

.2 Type D: welded steel construction with screw-on flat covers for surface mounting. Surface or flush mounting as indicated. Covers with 1” minimum extension all around, for flush-mounted pull and junction boxes.

.3 Junction and pull boxes larger than 5” x 5” to be Type "E", complete with continuously hinged door. Provide junction and pull boxes 5” x 5” and smaller complete with screw cover.

.4 Single gang "sectional" type devices boxes being used in steel stud walls for the installation of both metallic and non-metallic type cables, must not be sized smaller than 15.25in³, complete with wrap around type bracket.

.5 For two (2) or more flush installed sectional boxes, ganged together on boxes sized 100mm² and larger (intended for devices), provide an additional support bracket installed on opposite side of box, not presently secured to metal stud.

.6 Where larger sized devices or other types of "flush" outlet or junction boxes may be required, suitably sized 4 x 4" deep or 4-11/16" square boxes complete with appropriate sized extension tile rings are to be utilized. The use of plaster rings in lieu of tile type extension rings is not acceptable.

.7 Provide junction boxes 6" x 6" used in branch circuit wiring complete with bonding terminal strips.

2.2 CABINETS

.1 Type E: sheet steel, hinged screw- to-lock, door and return flange overlapping sides, handle, and catch, for surface mounting.

PART 3 - EXECUTION

3.1 JUNCTION, PULL BOXES AND CABINETS INSTALLATION

.1 Install pull boxes in inconspicuous but accessible locations.

NSLC Select Store Roll-Out Section 26 05 31 NSL-057 Berwick – November 2020 SPLITTERS, JUNCTION PULL BOXES AND CABINETS Page 2 of 2

.2 Mount cabinets with top not higher than 6.5 feet above finished floor.

.3 Only main junction and pull boxes are indicated. Install pull boxes so as not to exceed 100 feet of conduit run between pull boxes.

.4 Where located above accessible ceiling systems, locate enclosures within 30"of ceiling.

.5 Suspend enclosures on 1/3” plated steel threaded rod or secure rods to enclosure with one (1) flat washer and one nut on both sides of box.

.6 Provide number of threaded rod supports as follows: .1 Boxes up to 5” square: one (1) rod. .2 Boxes from 5” to 8” square: two (2) rods. .3 Boxes with dimensions above 8”: four (4) rods.

.7 Do not size concealed junction or outlet boxes feeding a maximum of two fixture drops smaller than 4in².

.8 Bond pull boxes and cabinets to ground utilizing a bonding conductor.

3.2 IDENTIFICATION

.1 Provide equipment identification in accordance with Section 26 05 00.

.2 Identify locations of conceded boxes installed above drywall ceilings or behind walls on the room side of access opening frames with properly colour coded identification disks.

END OF SECTION

NSLC Select Store Roll-Out Section 26 05 32 NSL-057 Berwick – November 2020 OUTLET BOXES, CONDUIT BOXES AND FITTINGS Page 1 of 2

PART 1 - GENERAL

1.1 REFERENCES

.1 CSA C22.1-2018, Canadian Electrical Code, Part 1.

PART 2 - PRODUCTS

2.1 OUTLET AND CONDUIT BOXES GENERAL

.1 Size boxes in accordance with CSA C22.1.

.2 4” square or larger outlet boxes as required for special devices.

.3 Gang boxes where wiring devices are grouped.

.4 Blank cover plates for boxes without wiring devices.

2.2 SHEET STEEL OUTLET BOXES

.1 Electro-galvanized steel single and multi-gang flush device boxes for flush installation, minimum size 3” x 2” x 1¾” or as indicated. 4” square outlet boxes when more than one conduit enters one side with extension and tile rings as required.

.2 Electro-galvanized steel utility boxes for outlets connected to surface-mounted EMT conduit, minimum size 4” x 2” x 2”.

.3 4” square or octagonal outlet boxes for lighting fixture outlets.

.4 4” square outlet boxes with extension and tile rings for flush mounting devices in finished walls.

2.3 MASONRY BOXES

.1 Electro-galvanized steel masonry single and multi-gang boxes for devices flush mounted in exposed block walls.

2.4 CONCRETE BOXES

.1 Electro-galvanized sheet steel concrete type boxes for flush mount in concrete with matching extension and plaster rings as required.

2.5 CONDUIT BOXES

.1 Cast FS or FD feralloy boxes with factory-threaded hubs and mounting feet for all surface wiring of devices (switches, receptacle, thermostats and similar devices) installed lower than 8' AFF. Matching steel type FS metal device plates specifically made for FS and FD boxes are to utilize four (4) point fastening.

NSLC Select Store Roll-Out Section 26 05 32 NSL-057 Berwick – November 2020 OUTLET BOXES, CONDUIT BOXES AND FITTINGS Page 2 of 2 2.6 FITTINGS- GENERAL

.1 Bushing and connectors with nylon insulated throats.

.2 Knock-out fillers to prevent entry of debris.

.3 Conduit outlet bodies for conduit up to 1¼’ and pull boxes for larger conduits.

.4 Double locknuts and insulated bushings on sheet metal boxes.

PART 3 - EXECUTION

3.1 INSTALLATION

.1 Support boxes independently of connecting conduits.

.2 Fill boxes with paper, sponges or foam or similar approved material to prevent entry of debris during construction. Remove upon completion of Work.

.3 For flush installations mount outlets flush with finished wall using plaster rings to permit wall finish to come within 6mm of opening.

.4 Provide correct size of openings in boxes for conduit, mineral insulated and armoured cable connections. Reducing washers are not allowed.

.5 Install flush mounted boxes in all finished areas unless otherwise indicated.

.6 Install surface mounted boxes in service rooms and above ceilings unless otherwise indicated.

.7 Install flush mounted boxes in outside of exterior walls unless otherwise indicated.

.8 Install type FS or FD boxes for all outlets (regardless of system type involved) to be surfaced mounted less than 8' AFF.

.9 Install concealed boxes in accessible locations.

.10 Flush installed 4” or 5” square box being used as a pull box or junction box shall have installed a single or double gauge tile ring and blank cover installed on the box.

.11 Do not use sectional type boxes with rigid galvanized steel conduit, rigid PVC conduit or EMT.

.12 Connect boxes to AC-90 cables specifically made for AC-90 cables only.

.13 In metal drywall partitions, install a short piece of metal stud (same width as wall) on non-supported side of box and secure to box.

.14 Install blank cover plates on all outlet boxes without wiring or telecommunication devices.

END OF SECTION

NSLC Select Store Roll-Out Section 26 05 34 NSL-057 Berwick – November 2020 CONDUITS, CONDUIT FASTENINGS AND FITTINGS Page 1 of 6

PART 1 - GENERAL

1.1 LOCATION OF CONDUIT

.1 Drawings do not indicate all conduit runs. Those indicated are in diagrammatic form only.

1.2 REFERENCES

.1 CSA C22.2 No. 45.1-07(R2017), Electrical Rigid Metal Conduit – Steel.

.2 CSA C22.2 No. 56-17, Flexible Metal Conduit and Liquid-Tight Flexible Metal Conduit.

.3 CSA C22.2 No. 83-1985(R2017), Electrical Metal Tubing.

.4 CAN/CSA C22.2 No. 211.1-06(R2016), Rigid Types EB1 and DB2/ES2 PVC Conduit

.5 CSA C22.2 No. 211.2-06(R2016), Rigid PVC (Unplasticized) Conduit.

1.3 TRADE SIZE

.1 The following are Metric trade sizes and Imperial trade size equivalent based on CEC Metric Units.

Metric (mm) Imperial (inch) 12 3/8 16 1/2 21 3/4 27 1 35 1-1/4 41 1-1/2 53 2 63 2-1/2 78 3 91 3-1/2 103 4 129 5 155 6

1.4 RELATED WORK

.1 Section 26 05 29: Fastenings and Supports.

PART 2 - PRODUCTS

2.1 OUTLET AND CONDUIT BOXES - GENERAL

.1 Size boxes in accordance with CSA C22.1.

.2 4” square or larger outlet boxes as required for special devices.


.3 Gang boxes where wiring devices are grouped.

.4 Blank cover plates for boxes without wiring devices.

2.2 CONDUITS

.1 Rigid galvanized steel threaded conduit, fittings and connectors: to CSA C22.2 No. 45.1.

.2 Electrical metallic tubing (EMT) with steel set screw couplings: to CSA C22.2 No. 83.

.3 Rigid PVC conduit, fittings; couplings and connectors: to CSA C22.2 No. 211.2.

.4 Flexible aluminum conduit and liquid-tight flexible metal conduit: to CSA C22.2 No. 56.

2.3 CONDUIT FASTENINGS

.1 One-hole steel straps to secure surface conduits smaller than 1½”. Two-hole steel straps for conduits 1½” and larger.

.2 Beam clamps to secure conduits to exposed steel work.

.3 Channel type supports for two or more conduits at 6” oc.

.4 1/3” dia. threaded rods to support suspended channels.

2.4 CONDUIT FITTINGS

.1 Fittings: manufactured for use with conduit specified. Coating: same as conduit.

.2 Conduit fittings (LB, LL, LR) are to be used for 90° bends. "Ells", or corner pulling "Elbows" are prohibited.

.3 Connectors and couplings for EMT: steel set-screws type.

.4 Waterproof type connectors shall be used on all vertical conduit runs connecting equipment.

.5 Plastic screw on bushings for conduit ends.

2.5 GENERAL FITTINGS

.1 Bushing and connectors with nylon insulated throats.

.2 Knock-out fillers to prevent entry of debris.

.3 Conduit outlet bodies for conduit up to 1¼” and pull boxes for larger conduits.

.4 Double locknuts and insulated bushings on sheet metal boxes.

NSLC Select Store Roll-Out Section 26 05 34 NSL-057 Berwick – November 2020 CONDUITS, CONDUIT FASTENINGS AND FITTINGS Page 3 of 6 2.6 EXPANSION FITTINGS FOR RIGID CONDUIT

.1 Weatherproof expansion fittings with internal bonding assembly suitable for 8” linear expansion.

.2 Watertight expansion fittings with integral bonding jumper suitable for linear expansion and ¾” deflection in all directions.

.3 Weatherproof expansion fittings for linear expansion at entry to panel.

2.7 FISH CORD

.1 Polypropylene: minimum 1/8” diameter.

2.8 WALL SLEEVES

.1 Minimum diameter 1” EMT.

.2 Refer to section 26 05 28 for bonding requirements.

PART 3 - EXECUTION

3.1 INSTALLATION

.1 Install conduits as high as possible to conserve headroom in exposed locations and cause minimum interference in spaces through which they pass.

.2 Conceal conduits except in mechanical and electrical service rooms and in unfinished areas. Install conduits as high as possible and secured to building structure with approved supports.

.3 Use electrical metallic tubing (EMT) except in cast concrete.

.4 Use rigid galvanized steel threaded conduit through poured concrete floor slabs and where otherwise specified.

.5 Use rigid PVC conduit underground: minimum size ¾” dia.

.6 Use liquid tight flexible metal conduit for connection to motors or vibrating equipment.

.7 Minimum conduit size for lighting and power circuits: ¾”.

.8 Bend conduit cold. Replace conduit if kinked or flattened more than 1/10th of its original diameter.

.9 Mechanically bend steel conduit over ¾” dia.

.10 Field threads on rigid conduit must be of sufficient length to draw conduits up tight.

.11 Install fish cord in empty conduits.


.12 Where conduits become blocked, remove and replace blocked section. Do not use liquids to clean out conduits.

.13 Dry conduits out before installing wire.

.14 Install insulated copper bonding conductor in all conduit runs. Minimum size: #14 AWG or Table 16 of C.E.C. whichever is larger.

.15 Non-connected PVC or steel raceways protruding up through open bottoms of free-standing equipment require PVC bell ends and steel type "ground bushings" installed on ends of respective types of conduits. Extend conduits a minimum of 2" above housekeeping pad or concrete trough.

.16 Install plastic bushings in all EMT sized 1¼” and larger before pulling in conductors.

.17 Use raintight EMT connectors and couplings complete with o-rings on vertical portion of conduit runs where terminating into tops of electrical equipment.

.18 Installation of conduit for control circuit wiring and structured cabling. .1 Install surface wiring in EMT. .2 Conduit to extend 30" of all various control devices associated with the operation

of any given piece of mechanical equipment or device they may feed. .3 Unless indicated otherwise, use liquid tight flexible metal conduit complete with

matching connectors for final connection between EMT and applicable control device. Junction or pull boxes may also be used to make this transition.

.4 Locate EMT type conduit wall stub complete with flush installed device box in all partitions to accommodate wiring between device and accessible ceiling.

.5 Install EMT connectors complete with nylon insulated throat or threaded type bushing on end of EMT stub where it protrudes through the wall above the accessible ceiling. EMT plastic end cap bushings that are CSA approved may also be used.

.6 Bond EMT conduit stubs to ground as required by the CEC.

.7 Turn out EMT conduit stubs installed in walls into the accessible ceiling space in the room where the associated wall box is located. Provide separate stubs for each room.

.8 Install telecommunications, CCTV, and security wiring through walls which do not form a rated fire separation in EMT sleeves. EMT plastic end cap bushings that are CSA approved may be used on each end.

.19 Where construction consists of metal Q-deck and steel joists (roof deck), install conduits as follows: .1 In such a manner that the nearest outside surface of the conduit is not less than

1½” from the nearest surface of the metal roof deck. Typically, this would involve the installation of conduits on the underside of the top flange, secured with beam clamps or canstrut.

.2 Installation of conduits or raceways between the top flange of a steel support structure and a steel roof deck is not permitted due to the possible penetration of roof deck mechanical screws or fasteners.

.20 Where construction consists of metal Q-deck and steel joists (non-roof deck), install conduits as follows: .1 Between the top flange of a steel support structure and the Q-deck. .2 Where conduit sizes preclude the above-mentioned method, install as high as

possible in the space to conserve headroom.

NSLC Select Store Roll-Out Section 26 05 34 NSL-057 Berwick – November 2020 CONDUITS, CONDUIT FASTENINGS AND FITTINGS Page 5 of 6 3.2 SURFACE CONDUITS

.1 Run parallel or perpendicular to building lines.

.2 Locate conduits behind infrared or gas fired heaters with 5-foot clearance.

.3 Run conduits in flanged portion of structural steel.

.4 Group conduits wherever possible on suspended or surface channels.

.5 Do not pass conduits through structural members except as indicated.

.6 Do not locate conduits less than 3” parallel to steam or hot water lines with minimum of 1” at crossovers.

3.3 CONDUITS UNDERGROUND

.1 Slope conduits to provide drainage.

.2 Waterproof joints (PVC accepted) with heavy coat of bituminous paint.

.3 Conduits are only permitted to be installed below floors and are not to be installed in concrete floors unless specifically indicated otherwise.

.4 Install PVC conduits sized 1¼" and larger in trenches not less than 12" in depth from underside of concrete floor slab to bottom of trench. Place conduits on a 2" bed of sand and place a second 2" bed of sand on top. Surround conduits in sand prior to backfilling taking place.

.5 Perform wiring for all various systems devices and/or outlets installed below ground floor concrete floor slabs utilizing minimum 3/4" PVC rigid conduit. Transition from PVC rigid thick wall conduit to rigid steel threaded conduit is to take place below the floor slab. Transition from rigid steel to EMT above concrete floor slab.

.6 Up-size underground conduit one (1) trade size above the minimum code requirement.

.7 Rigid PVC (thick wall) conduit will be permitted to be direct buried.

.8 Underground and underslab conduits are only permitted to be installed where specifically indicated.

.9 Install PVC conduits sized 1¼” in diameter and larger in trenches not less than 12” in depth from underside of concrete floor slab to bottom of trench. Place conduits on a 2” bed of sand and place 2” of sand on top. Surround conduits in sand prior to backfilling.

.10 Conduit installation is not to influence the thickness of the floor slab.

.11 Do not run conduits along concrete walls installed to reinforce wall installations.

.12 Wiring for all various systems devices and/or outlets installed below ground floor concrete floor slabs may be performed utilizing code approved, minimum ¾” PVC rigid type conduit. Transition from PVC rigid thick wall conduit to rigid steel threaded conduit to take place "below" floor slab. Transition from rigid steel threaded conduit to EMT type conduit to take place "above" concrete floor slab.


.13 PVC conduits of all sizes prior to turning-up through floor slabs, unless specifically indicated otherwise, are to have transition to rigid steel threaded conduit take place as previously indicated.

.14 The installation of PVC type conduits above ground is prohibited.

.15 Up size underground conduits at least one trade size above the minimum code requirement for ease of pulling.

.16 Rigid Types EB1 and DB2/ES2 PVC (thin wall) Conduit (CSA C22.2 211.1) will only be used where embedded in concrete.

.17 Rigid PVC (thick wall) Conduit (CSA C22.2 211.2) will be permitted to be direct buried.

END OF SECTION

NSLC Select Store Roll-Out Section 26 24 17 NSL-057 Berwick – November 2020 PANELBOARDS BREAKER TYPE Page 1 of 3

PART 1 - GENERAL

1.1 SHOP DRAWINGS

.1 Submit shop drawings in accordance with Section 01 33 00 – Submittal Procedures.

.2 Drawings to include electrical detail of panel, branch breaker type, breaker quantity, ampacity, short circuit rating, bus materials and enclosure dimension.


.1 Provide operation and maintenance data for panelboards for incorporation into manual specified in Section 01 78 00 – Closeout Submittals.

.2 Include panel schedules.

1.3 REFERENCES

.1 IEEE C62.41.1-02(R2008), Guide on the Surges Environment in Low-Voltage AC Power Circuits.

.2 IEEE C62.45-02(R2008), Recommended Practice on Surge Testing for Equipment Connected to Low-Voltage AC Power Circuits.

.3 UL 1449-15(R2018), UL Standard for Safety Surge Protection Devices.

.4 UL 1283-2018, UL Standard for Safety Electromagnetic Interference Filters.

PART 2 - PRODUCTS

2.1 PANELBOARDS

.1 Panelboards: use the product of one (1) manufacturer throughout.

.2 250 and 600 V panelboards: bus and breakers rated as indicated.

.3 Sequence phase bussing with odd numbered breakers on left and even on right, with each breaker identified by permanent number identification as to circuit number and phase.

.4 Panelboards: mains, number of circuits, and number and size of branch circuit breakers as indicated.

.5 Two (2) keys for each panelboard and key panelboards alike.

.6 Tin-plated copper bus. Neutral to be 100% rated of mains.

.7 Mains: suitable for bolt-on breakers.

.8 Trim with concealed front bolts and hinges.


.9 Trim and door finish: baked grey enamel.

.10 Minimum of one (1) terminal screw on factory installed neutral bar for each circuit breaker position.

2.2 BREAKERS

.1 Breakers: to Section 26 28 21 - Moulded Case Circuit Breakers.

.2 Breakers with thermal and magnetic tripping in panelboards except as indicated otherwise.

.3 Main breaker: separately mounted on top or bottom of panel to suit cable entry. When mounted vertically, down position should open breaker.

.4 Lock-on devices for 10% of 15 to 30 A breakers installed as indicated. Turn over unused lock-on devices to the Consultant or Owner.


.1 Provide equipment identification in accordance with Section 26 05 00 - Electrical General Requirements.

.2 Nameplate for each panelboard size 4 engraved as indicated.

.3 Nameplate for each circuit in distribution panelboards size 2 engraved as indicated.

.4 Complete circuit directory with typewritten legend showing location and load of each circuit.

2.4 STANDARD OF ACCEPTANCE

.1 Branch panels: Siemens P2.

2.5 ACCEPTABLE MANUFACTURERS

.1 Siemens

.2 Eaton

.3 Schneider

PART 3 - EXECUTION

3.1 INSTALLATION

.1 Locate panelboards as indicated and mount securely, plumb, true and square, to adjoining surfaces.

.2 Mount panelboards to height specified in Section 26 05 00 - Electrical General Requirements or as indicated.


.3 Connect loads to circuits.

.4 Connect neutral conductors to common neutral bus with respective neutral identified.

.5 Where more than one bonding terminal strip is present in one panel, hardwire both together using same size bonding conductor as the one that accompanies the panel feeder conductors.

END OF SECTION

NSLC Select Store Roll-Out Section 26 27 26 NSL-057 Berwick – November 2020 WIRING DEVICES Page 1 of 4

PART 1 - GENERAL


.1 Section 01 33 00 – Submittal Procedures

.2 Section 01 78 00 – Closeout Submittals

1.2 REFERENCES

.1 CSA C22.2 No. 42-10(R2020), General Use Receptacles, Attachment Plugs and Similar Wiring Devices.

.2 CSA C22.2 No. 55-15(R2020), Special Use Switches.

.3 CSA C22.2 No. 111-2018, General Use Snap Switches.

1.3 SHOP DRAWINGS

.1 Submit shop drawings for each device and coverplate type as per specification Section 01 33 00 – Submittal Procedures.

1.4 OPERATIONAL AND MAINTENANCE DATA

.1 Provide operation and maintenance data for wiring devices for incorporation into manual specified in Section 01 78 00 – Closeout Submittals.

PART 2 - PRODUCTS

2.1 SWITCHES

.1 Design S1: .1 20 A, 120 V, specification grade single pole, two- or three-way switches as

indicated. .2 Manually-operated general purpose ac switches with following features:

.1 Terminal holes approved for No. 10 AWG wire.

.2 Silver alloy contacts.

.3 Urea or melamine molding for parts subject to carbon tracking.

.4 Suitable for back and side wiring.

.5 White nylon, heavy duty toggle.

.6 Integral ground terminal. .3 Toggle operated fully rated for tungsten filament and fluorescent lamps, and up

to 80% of rated capacity of motor loads. .4 Provide the switches of one (1) manufacturer throughout project. .5 Standard of Acceptance: Hubbell 1200 Series. .6 Approved Manufacturers:

.1 Hubbell

.2 Pass & Seymour

.3 Arrow Hart


.4 Leviton

.5 Bryant

2.2 RECEPTACLES

.1 Design R1: .1 General purpose duplex receptacles, specification grade CSA type 5- 15R, 125

V, 15 A, U ground, with following features: .1 White urea molded housing. .2 Suitable for No. 10 AWG for back and side wiring. .3 Break-off links for use as split receptacles. .4 Eight (8) back wired entrances, four (4) side wiring screws. .5 Triple wipe contacts and rivetted grounding contacts. .6 Standard of Acceptance: Hubbell 5262-W Series. .7 Approved Manufacturers:

.1 Hubbell

.2 Pass & Seymour

.3 Arrow Hart

.4 Leviton

.5 Bryant

.2 Design R2: .1 Duplex receptacles, specification grade CSA type 5-20R (T-Slot), 125 V, 15/20A,

U ground, with following features: .1 White urea molded housing. .2 Suitable for No. 10 AWG for back and side wiring. .3 Break-off links for use as split receptacles. .4 Eight (8) back wired entrances, four (4) side wiring screws. .5 Triple wipe contacts and rivetted grounding contacts. .6 White nylon face. .7 Standard of Acceptance: Hubbell 5362-W Series. .8 Acceptable Manufacturers:

.1 Hubbell

.2 Pass & Seymour

.3 Arrow Hart Leviton

.4 Bryant

.5 Leviton

.3 Design R3: .1 GFI duplex receptacles: Specification grade, CSA type 5-15R, 125V, 15A, U-

Ground with the following features: .1 White urea moulded housing. .2 Suitable for No. 10 AWG for back and side wiring. .3 Eight (8) back wired entrances, four (4) side wiring screws. .4 Triple wipe contacts and riveted grounding contacts. .5 White nylon face. .6 GFI test and reset buttons. .7 Standard of Acceptance:

.1 Hubbell GFRST15W Series. .8 Approved Manufacturers:

.1 Hubbell

.2 Pass & Seymour

.3 Arrow Hart

.4 Leviton

.5 Bryant


.4 Design R4: .1 Isolated ground duplex receptacles, specification grade CSA type 5-20R (T-slot),

125V, 15/20A, U-ground, with following features. .1 Orange urea moulded housing. .2 Suitable for No. 10 AWG for back and side wiring. .3 Break-off links for use as split receptacles. .4 Eight (8) back wired entrances, four (4) side wiring devices. .5 Triple wide contacts and riveted grounding contacts. .6 Standard of Acceptance: Hubbell 5362-W Series. .7 Approved manufacturers:

.1 Hubbell

.2 Pass & Seymour

.3 Arrow Hart

.4 Bryant

.5 Leviton

.5 Recessed Multimedia Device Box for Cannabis Television. .1 Television wiring devices and data outlets to be installed in a double gang

recessed back box, specially designed for the application. .1 Per one(1) television location provide:

.1 One(1) 15A, 5-15R duplex receptacle.

.2 Two(2) RJ45 data outlets. .2 Standard of acceptance: Legrand Wiremold #TV2MW.

.6 Other receptacles with ampacity and voltage as indicated.

.7 Use the receptacles of one (1) manufacturer throughout project.

2.3 COVER PLATES

.1 Cover plates for wiring devices.

.2 Sheet steel utility box cover for wiring devices installed in surface-mounted utility boxes.

.3 Brushed stainless steel plates for wiring devices mounted in flush-mounted outlet box.

.4 Sheet metal cover plates for wiring devices mounted in surface-mounted FS or FD type conduit boxes.

.5 Weatherproof while-in-use covers, heavy cast aluminum cover plate, complete with neoprene gaskets and enclosure key for duplex receptacles mounted on exterior of building.

PART 3 - EXECUTION

3.1 INSTALLATION

.1 Switches: .1 Install single throw switches with handle in "UP" position when switch closed. .2 Install switches in gang type outlet box when more than one switch is required in

one location. .3 Mount toggle switches at height specified in Section 26 05 00 - Electrical General

Requirements or as indicated.


.2 Receptacles: .1 Install receptacles in gang type outlet box when more than one receptacle is

required in one location. .2 Mount receptacles at height specified in Section 26 05 00 - Electrical General

Requirements or as indicated. .3 Where split receptacle has one portion switched, mount vertically and switch

upper portion. .4 Mount receptacles with "U" ground up for vertically mounted and neutral slot at

top for horizontally mounted receptacle. .5 Install "Pigtail" type leads on conductors in all device or outlet boxes where

feeding through to other receptacles. "Daisy-chain" or looping through of conductors from one device to another is not acceptable. Provide separate pigtail conductor leads for final termination to each receptacle for phase, neutral and bond conductors.

.6 Test all receptacles for polarity.

.3 Cover plates: .1 Protect cover plate finish with paper or plastic film until painting and other Work is

finished. .2 Install suitable common cover plates where wiring devices are grouped. .3 Do not use cover plates meant for flush outlet boxes on surface-mounted boxes.

.4 Device leveler and retainer is an approved accessory for securing devices to flush installed device boxes.

.5 Single gang adjustable box extension is an approved accessory for extending single gang box openings a maximum of ¾”. Their use is acceptable in non-combustible type walls where front edges of boxes have not been installed greater than 1” or ¼” from wall surface.

END OF SECTION

NSLC Select Store Roll-Out Section 26 28 21 NSL-057 Berwick – November 2020 MOULDED CASE CIRCUIT BREAKERS Page 1 of 2

PART 1 - GENERAL

1.1 PRODUCT DATA


.2 Include circuit breaker types, ratings, magnetic adjustment ranges and time-current characteristic curves for breakers with ampacity of 225 A and over.


.1 Provide operation and maintenance data for circuit breakers for incorporation into Manual specified in Section 01 78 00 – Closeout Submittals.

.2 Include matrix of individual circuit breaker settings for all breakers with adjustable settings.

PART 2 - PRODUCTS

2.1 BREAKERS − GENERAL

.1 Bolt-on moulded case circuit breaker: quick- make, quick-break type, for manual and automatic operation with temperature compensation for 40°C ambient.

.2 Multiple breakers shall have single handle.

.3 Magnetic instantaneous trip elements in circuit breakers to operate only when value of current reaches setting. Trip settings on breakers with adjustable trips to range from 3-8 times current rating.

.4 Circuit breakers with interchangeable trips as indicated.

.5 Circuit breakers to have interrupting capacity as indicated on the Drawings.

.6 Service entrance main breaker 100% rated, solid-state type overcurrent protective trip unit with independently adjustable LSI settings. Main breaker to be installed in a service entrance rated enclosure.

2.2 THERMAL MAGNETIC BREAKERS

.1 Moulded case circuit breaker to operate automatically by means of thermal and magnetic tripping devices to provide inverse time current tripping and instantaneous tripping for short circuit protection.

2.3 MAGNETIC BREAKERS

.1 Moulded case circuit breaker to operate automatically by means of magnetic tripping devices to provide instantaneous tripping for short circuit protection.

NSLC Select Store Roll-Out Section 26 28 21 NSL-057 Berwick – November 2020 MOULDED CASE CIRCUIT BREAKERS Page 2 of 2 2.4 SOLID STATE TRIP BREAKERS

.1 Moulded case circuit breaker to operate by means of a solid-state trip unit with associated current monitors and self- powered shunt trip to provide inverse time current trip under overload condition, and longtime short time instantaneous tripping for phase ground fault short circuit protection. Settings must be individually adjustable.

2.5 OPTIONAL FEATURES

.1 Include: .1 On-off locking device for 10% of branch breakers and all breakers supplying exit

lighting.

2.6 GROUND FAULT CIRCUIT INTERRUPTER CIRCUIT BREAKERS

.1 Moulded case thermal magnetic circuit breaker with Class A ground fault protection.

PART 3 - EXECUTION

3.1 INSTALLATION

.1 Install circuit breakers as required, factory install breakers in all panelboards, switchboards and distribution panels.

.2 Adjust circuit breaker settings to the values indicated on the manufacturer's supplied Coordination Study.

.3 Install individual circuit breakers in CSA Type 1 enclosures complete with bonding and neutral connections.

.4 Terminate existing system ground wire in service entrance breaker enclosure.

END OF SECTION

NSLC Select Store Roll-Out Section 26 28 23 NSL-057 Berwick – November 2020 DISCONNECT SWITCHES – FUSED AND NON-FUSED Page 1 of 2

PART 1 - GENERAL




.3 Section 26 05 00 - Electrical General Requirements

1.2 PRODUCT DATA


.2 Include: .1 Dimensions. .2 Enclosure type. .3 Rating. .4 Accessories.


.1 Provide operation and maintenance data for disconnect switches for incorporation into manual specified in Section 01 78 00 – Closeout Submittals.

PART 2 - PRODUCTS

2.1 DISCONNECT SWITCHES

.1 Heavy duty, fusible and non-fusible, horsepower rated disconnect switch in CSA Enclosure type as indicated (minimum CSA type 1 with driphood) size as indicated.

.2 Provision for padlocking in off switch position by three locks.

.3 Mechanically interlocked door to prevent opening when handle in ON position.

.4 Fuses: size as indicated.

.5 Fuseholders: suitable without adaptors, for type and size of fuse indicated.

.6 Quick-make, quick-break action.

.7 ON-OFF switch position indication on switch enclosure cover.

.8 Viewing window to view open/close status of disconnect switch blades.

.9 Service entrance rated as indicated.

.10 Acceptable manufacturers: .1 Siemens.

NSLC Select Store Roll-Out Section 26 28 23 NSL-057 Berwick – November 2020 DISCONNECT SWITCHES – FUSED AND NON-FUSED Page 2 of 2

.2 Eaton.

.3 Schneider.



.2 Indicate name of load controlled voltage panel designation and circuit numbers on size 4 nameplate.

PART 3 - EXECUTION

3.1 INSTALLATION

.1 Install disconnect switches complete with fuses where required.

.2 Maintain acceptable working clearances prior to rough-in.

END OF SECTION

NSLC Select Store Roll-Out Section 26 29 10 NSL-057 Berwick – November 2020 MOTOR STARTERS TO 600V Page 1 of 3

PART 1 - GENERAL




.3 Section 26 05 00 - Electrical General Requirements



.2 Indicate: .1 Mounting method and dimensions. .2 Starter size and type. .3 Layout of identified internal and front panel components. .4 Enclosure types. .5 Wiring diagram for each type of starter. .6 Interconnection diagrams.


.1 Provide operation and maintenance data for motor starters for incorporation into manual specified in Section 01 78 00 – Closeout Submittals.

.2 Include operation and maintenance data for each type and style of starter.

PART 2 - PRODUCTS

2.1 MATERIALS

.1 Starters: EEMAC E14-1 .1 Half size starters are not acceptable. .2 IEC equipment not acceptable.

.2 Acceptable manufacturers: .1 Eaton .2 Schneider .3 Siemens

2.2 MANUAL MOTOR STARTERS

.1 Single phase manual motor starters of size, type, rating, and enclosure type as indicated, with components as follows: .1 Switching mechanism, quick make and break.


.2 All phase conductors to have overload heaters, manual reset, trip indicating handle.

.2 Accessories: .1 Toggle switch: heavy duty labeled as indicated. .2 Indicating light: LED and colour as indicated. .3 Locking tab to permit padlocking in "ON" or "OFF" position.

2.3 FULL VOLTAGE MAGNETIC STARTERS

.1 Magnetic and combination magnetic starters of size, type, rating and enclosure type as indicated with components as follows: .1 Contactor solenoid operated, rapid action type. .2 Motor overload protective device in each phase, manually reset from outside

enclosure. .3 Wiring and schematic diagram inside starter enclosure in visible location. .4 Identify each wire and terminal for external connections, within starter, with

permanent number marking identical to diagram. .5 Hand-off-auto selection switch in cover. .6 LED pilot light indicating coil is energized. .7 LED pilot light indicating unit is powered.

.2 Combination type starters to include motor circuit interrupter with operating lever on outside of enclosure to control motor circuit interrupter, and provision for: .1 Locking in "OFF" position with up to three (3) padlocks. .2 Independent locking of enclosure door. .3 Provision for preventing switching to "ON" position while enclosure door open.

.3 Accessories: .1 Selector switches: heavy duty labeled as indicated. .2 Indicating lights: LED type and color as indicated. .3 One (1)-N/O and one (1)-N/C spare auxiliary contacts unless otherwise indicated. .4 Provide solid state protection complete with single phasing protection. .5 Provide one (1) 24 VAC interposing relay complete with two (2) normally open and

two (2) normally closed contacts mounted in starter cell. Connect relay as indicated.

2.4 CONTROL TRANSFORMER

.1 Single phase, dry type, control transformer with primary voltage as indicated and 120V secondary, complete with secondary fuse, installed in starter as indicated.

.2 Size control transformer for control circuit load plus 20% spare capacity.

2.5 FINISHES

.1 Apply finishes to enclosure in accordance with Section 26 05 00 - Electrical General Requirements.




PART 3 - EXECUTION

3.1 INSTALLATION

.1 Install starters, connect power and control as indicated.

.2 Ensure fuses and overload elements are correct for the actual loads. Obtain correct information from Divisions 21, 22 and 23 prior to ordering and setting overloads.

.3 Coordinate with the Controls subcontractor.


.1 Perform tests in accordance with Section 26 05 00 - Electrical General Requirements and manufacturer's instructions.

.2 Operate switches, contactors to verify correct functioning.

.3 Perform starting and stopping sequences of contactors and relays.

.4 Confirm sequence controls, interlocking with other separate related starters, equipment, control devices, operate as required.

.5 Provide test forms to the Consultant for each motor starter confirming operation and settings.

END OF SECTION

NSLC Select Store Roll-Out Section 26 50 00 NSL-057 Berwick – November 2020 LIGHTING EQUIPMENT Page 1 of 3

PART 1 - GENERAL

1.1 REFERENCES

.1 IEEE C62.41.1-02(R2008), Guide on the Surges Environment in Low-Voltage (1000 V and less) AC Power Circuits.

.2 ANSI C62.45-2002, Guide on Surge Testing for Equipment Connected to Low- Voltage AC Power Circuits.

.3 NECA/NEIS 500-2006, Standard for Installing Indoor Lighting Systems.

.4 IES RP-1-2012; Practice for Office Lighting.

.5 ASTM F1137/F1137M-19, Standard Specification for Phosphate/Oil Corrosion Protective Coatings for Fasteners.

.6 FCC 47 CFR 2-2010; Frequency Allocations and Radio Treaty Matters; General Rules and Regulations.


.1 Section 01 33 00 - Submittal Procedures.

.2 Section 01 74 19 – Waste Management and Disposal.



.2 Submit shop drawings for the following: .1 Luminaire. .2 Lamp for each luminaire type. .3 Ballast/Driver for each luminaire type.

.3 Shop Drawings: .1 Shop drawings to clearly indicate the following:

.1 Luminaire ID number as identified in contract documents.

.2 Fixture specification as identified in Part 2 and on the drawings.

.3 Ballast/Driver specification as identified in Part 2 and on the drawings.

.4 Photometric data for each luminaire type.

.5 Energy data for ballasts.

.4 Catalogue cuts lacking sufficient detail to indicate compliance with Contract documents will not be acceptable.

.5 Submit complete photometric data prepared by independent testing laboratory for luminaires where specified, for review by Consultant. Photometric data to include: .1 VCP Table, spacing criterion; .2 Total input watts; .3 Candlepower summary, candela distribution, zonal lumen summary; .4 Luminaire efficiency, C.I.E. type, coefficient of utilization;

NSLC Select Store Roll-Out Section 26 50 00 NSL-057 Berwick – November 2020 LIGHTING EQUIPMENT Page 2 of 3

.5 Lamp type;

.6 Lumen ratings

.7 Summary in accordance with IES procedures.

.8 Electronic IES file (provide on CD).

1.4 OPERATION AND MAINTENANCE

.1 Provide operation and maintenance data for inclusion in the manual specified in Section 01 78 00 – Closeout Submittals

1.5 WASTE AND DISPOSAL

.1 Separate and recycle waste materials in accordance with Section 01 74 19 – Waste Management and Disposal.

.2 Place materials defined as hazardous or toxic waste in designated containers.

.3 Seal emptied containers and store safely for disposal.

.4 Refer to section 01 74 19 - Waste Management and Disposal for disposal of fluorescent lamps.

PART 2 - PRODUCTS

2.1 DRIVERS

.1 Electronic LED driver: .1 Performance requirements:

.1 Voltage: as indicated.

.2 Power factor: greater than 0.90.

.3 Total harmonic distortion: less than 20%.

.4 Efficiency: 85% or greater. .2 Regulatory requirements:

.1 Underwriters Laboratories (UL) listed and Canadian Standards Association approved.

.2 Meet or exceed ANSI C62.41 Category A for transient protection.

.3 Meet or exceed NEMA SSL 1 where applicable.

.4 Meet or exceed the requirements of the Federal Communications commission (FCC) rules and regulations, Title 47 CFR part 15, non-consumer (Class A) for EMI/RFI (conducted and radiated).

2.2 SPARES

.1 Provide 5% spare drivers of each type to a minimum quantity of five (5).

2.3 LUMINAIRES

.1 Luminaires are specified on the drawings.

NSLC Select Store Roll-Out Section 26 50 00 NSL-057 Berwick – November 2020 LIGHTING EQUIPMENT Page 3 of 3 PART 3 - EXECUTION

3.1 INSTALLATION

.1 Locate and install luminaires as indicated. Provide and install all necessary hangars, supports, fittings, etc. as necessary for a complete installation.

.2 Coordinate installation with all other services.

3.2 WIRING

.1 Connect luminaires to lighting circuits as indicated.

.2 Each light fixture to have a separate "fixture drop" installed and connected to hard wired junction box or outlet box in ceiling space.

.3 Recessed and/or surface type fluorescent light fixtures are not to be wired in a "daisy-chain" manner or have their power sources looped between fixtures, unless the fixtures are installed end-to-end or house an integral junction box.

3.3 LUMINAIRE SUPPORTS

.1 For suspended ceiling installations, support luminaires independently of ceiling using an approved supporting method. Supporting luminaires from any part of the ceiling system is strictly prohibited.

3.4 LUMINAIRE ALIGNMENT

.1 Align luminaires mounted in continuous rows to form straight uninterrupted line.

.2 Align luminaires mounted individually parallel or perpendicular to building grid lines.

END OF SECTION

NSLC Select Store Roll-Out Section 26 50 05 NSL-057 Berwick – November 2020 LIGHTING CONTROL SYSTEM Page 1 of 6

PART 1 - GENERAL

1.1 SUMMARY

.1 Related Sections: .1 Section 26 27 26 - Wiring Devices: Receptacles. .2 Section 26 50 00 - Lighting Equipment

.2 The building consists of a single level of combined retail space, refrigerated retail & storage, warehouse facility, service rooms, water closets, and office spaces.

1.2 DESCRIPTION OF WORK

.1 Supply and install a complete system for the control of lighting and other equipment as indicated on the lighting and lighting control system (LCS) drawings and as further defined herein. The LCS will be based on addressable device technology and allow individual luminaire control. All devices such as ballasts, drivers, incandescent modules, etc., must be compatible and fully function with the LCS.

.2 Verify quantity of specific devices and equipment required for this project. Be responsible for providing all components and accessories necessary to install a fully functional lighting control system.

.3 System to include but not be limited by the following list: Pre-wired, microprocessor control panels controlled via a complete list of communication based accessories including digital switches, dual technology occupancy sensors and interface cards to fire alarm system, security/intrusion alarm system, access control system, and other devices as indicated herein or as necessary for the proper operation of the lighting control system.

.4 The lighting control system may utilize wired components only to achieve the functionality required.

1.3 REFERENCES

.1 IEEE C62.41.1-02(R2008), Guide on the Surges Environment in Low-Voltage (1000V and Less) AC Power Circuits.

.2 UL 20-2018, UL Standard for Safety General Use Snap Switches.

.3 UL 94-2018, UL Standard for Safety Tests for Flammability of Plastic Materials for Parts in Devices and Appliances.

.4 UL 508-2018, UL Standard for Safety Industrial Control Equipment.

.5 UL 1472-2017, UL Standard for Safety Solid State Dimming Controls

.6 ASTM D4674-2019, Standard Practice for Accelerated Testing of Color Stability of Plastics Exposed to Indoor Office Environments.

NSLC Select Store Roll-Out Section 26 50 05 NSL-057 Berwick – November 2020 LIGHTING CONTROL SYSTEM Page 2 of 6 1.4 CONSTRUCTION SUBMITTALS

.1 Shop Drawings: submit dimensioned drawings of lighting control system and accessories including, but not necessarily limited to, control panels, controllers, control stations, switches, DTC, photocells, occupancy sensors and other interfaces. Shop drawings to indicate locations of each device.

.2 One Line Diagram: submit a one- line diagram of the system configuration indicating the type, size and number of conductors between each component. One-line diagram also to indicate all auxiliary system interface components. Submittals that show typical riser diagrams are not acceptable.

.3 Separate Price List: submit with the shop drawings separate pricing for individual components (and associated auxiliaries). Also submit pricing for any other components which may be deemed necessary not included in the base design. Pricing to include the supply, delivery as well as any associated programming of such components. The submitted pricing must be valid until the Substantial Completion of the project.

.4 Provide information on the Manufacturer including head office location, Canadian office locations, local sales representative and local service representative.

1.5 MAINTENANCE MATERIALS

.1 Provide the following information for submission as per Section 01 78 00 – Closeout Submittals. .1 Provide, at the completion of the project, Operation and Maintenance materials

for inclusion in the Operation and Maintenance Manual. These materials must, at a minimum, include product data, shop drawings, updated single line diagram (indicating any modifications, additions or subtractions made from the time of Tender to the completion of construction), CD version of the operating software including graphical interface software, letter verifying installation, letter verifying start-up and commissioning.

.2 Provide, at the completion of the project, separate pricing for individual components (and associated auxiliaries). Also submit pricing for any other components or services which may be deemed necessary. Pricing to include the supply, delivery as well as any associated programming of such components. The submitted pricing must be valid for one (1) year from the date of Substantial Completion and be specifically identified by the Vendor.

.3 Provide, at the completion of the project, a listing of recommended spare components with which may be deemed necessary under normal operation of: .1 1000 hours .2 One (1) years .3 Three (3) years .4 Five (5) years

1.6 SYSTEM DESCRIPTION

.1 The lighting control system must be able to communicate with digital switches, occupancy sensors, and various interfaces.

.2 Pre-address devices at the factory. Field addressing is not acceptable.


.3 The system must be capable of implementing On and Off commands for any relay, group or zone by means of digital wall switches, occupancy sensor, or other devices connected to programmable inputs in the lighting controller.

.4 The system may consist of centralized controllers, digital switches, occupancy sensors and various digital interfaces. Verify exact type and quantity of system components which are required based on the lighting controls design and the proposed lighting control system. Wire devices connected to the lighting control system per lighting control manufacturer’s instructions.

.5 Equip system with a minimum of 10% spare capacity for addition of future devices.

.6 The following section describes the general system operation and control requirements for the majority of the building spaces, specifics regarding quantities, controls and locations of required devices are indicated on the drawings: .1 General: New interior lighting in the office, retail, walk-in cooler and warehouse

areas to be integrated into one (1) common lighting control system. .2 Retail and Walk-in Cooler: Control lighting in these areas via one (1) low voltage

switch located inside the office. .3 Office: Provide one (1) low voltage wall switch with dimming capability to control

office LED flat panels. .4 Cannabis Retail: LED flat panels to be controlled via retail master switch. Provide

one (1) low voltage switch with dimming capability at location shown on drawings to control the two (2) decorative pendants.

.5 Warehouse: Existing fluorescent fixtures are to be controlled via new occupancy sensor(s) that automatically turn the lighting on when motion is detected, and off after an adjustable time delay. Provide low voltage switches located at all entrances as seen on the drawings for local override.

.6 Integration with Building Systems: Incorporate control signal input from the security/intrusion alarm system into the lighting control system. The inputs are to be N/O contacts connected to the Intrusion Detection System panel located in the main electrical room. Each input is to act as a "master switch" turning on or off all lighting controlled by the new control system in the building.

1.7 QUALITY ASSURANCE

.1 Products to be manufactured by a firm regularly engaged in manufacture of lighting control equipment and ancillary equipment, of types and capacities required, whose products have been in successfully used in similar service for not less than five (5) years.

1.8 PROJECT CONDITIONS

.1 Do not install equipment until following conditions can be maintained in spaces to receive equipment: .1 Ambient temperature: 0 degrees to 40 degrees C (32 degrees to 104 degrees F). .2 Relative humidity: Maximum 90 percent, non-condensing. .3 Lighting control system must be protected from dust during installation.

1.9 WARRANTY

.1 Provide a minimum of one (1) year warranty on the entire lighting control system including components, software and hardware. The warranty will begin on the date of Substantial Completion.

NSLC Select Store Roll-Out Section 26 50 05 NSL-057 Berwick – November 2020 LIGHTING CONTROL SYSTEM Page 4 of 6 PART 2 - PRODUCTS

2.1 GENERAL

.1 Provide system hardware that is designed, tested, manufactured, and warranted by a single manufacturer.

2.2 MATERIAL AND COMPONENTS

.1 Power Interfaces: .1 Provide power interfaces as required. .2 Electrical: Phase independent of control input. .3 Diagnostics and Service: Replacing power interface does not require re-

programming of system or processor.

.2 Low Voltage Wall Stations: .1 Low voltage or wireless operation. .2 Two-button or two-button with manual raise/lower as indicated on drawings. .3 Finish to be white. .4 Engrave wall stations in English with appropriate button, zone, and scene

engraving descriptions furnished prior to fabrication.

.3 Occupancy/Vacancy Sensors: .1 Wall, ceiling, or corner mounted as indicated on drawings. .2 Provide all necessary mounting hardware. .3 Dual technology: passive infrared (PIR) and acoustic sensing technologies. .4 Powered through the lighting control system. Occupancy sensors requiring

separate power packs will not be accepted.

.4 Acceptable Manufacturers: .1 Lutron .2 N-Light .3 Wattstopper .4 ILC

PART 3 - EXECUTION

3.1 EQUIPMENT INSTALLATION

.1 Install equipment in accordance with manufacturer's installation instructions.

.2 Provide complete installation of system in accordance with Contract Documents.

.3 Provide equipment at locations and in quantities indicated on Drawings. Provide any additional equipment required to provide control intent.

.4 Wiring: .1 Do not mix low voltage and high voltage conductors in the same conduit. No

exceptions. .2 Confirm low voltage conduits or control wires do not run parallel to current

carrying conduits.


.3 Place manufacturer supplied termination devices at each end of the system bus per manufacturers' instructions.

.4 Neatly lace and rack wiring in cabinets.

.5 Plug in Category 6 patch cable that has been field-tested with a recognized cable tester, at the indicated RJ45 connector provided at each lighting control device as applicable, per manufacturer’s instructions.

.6 Use Category 6 patch cable for all system low voltage connections. Additional conductors may be required to compensate for voltage drop with specific system designs. Manufacturer to recommend cabling type if different. Use shielded cable for dry contact inputs to lighting control system.

.7 Do not exceed 48” wire length for the system bus.

.8 All items on the bus shall be connected in sequence (daisy chained). Star and spur topologies are not acceptable.

.9 Install specified lighting control system and make all necessary wiring connections to external devices and equipment, including intrusion alarm and fire alarm systems. Wire per manufacturer instructions.

3.2 INSTALLATION AND SET-UP

.1 Coordinate all programming and operation requirements with the Owner prior to programming of the lighting control system functions. Arrange a meeting with the Manufacturer's representative, the Owner and Consultant at a location determined by the Owner to coordinate these requirements.

.2 Before Substantial Completion, arrange and provide a minimum of four (4) hours of instruction period to designated facility personnel, provided by a Factory trained manufacturer's representative.

.3 Set-up, commissioning of the lighting control system, and Owner instruction includes: .1 Confirmation of entire system operation and communication to each device. .2 Confirmation of operation of individual relays, switches and occupancy sensors. .3 Confirmation of system Programming, override settings, etc. .4 Provide training to cover installation, maintenance, troubleshooting,

programming, and repair and operation of the lighting control system. .5 Confirmation of ballast and driver operation.

.4 Service and Operation Manuals: .1 Submit operation and service manuals. Submit complete manuals in a binder,

data typewritten or drafted. Refer to other sections of the project specifications for numbers of required copies of the service and operation manuals.

.2 Manuals to include instructions necessary for proper operation and servicing of system and shall include complete wiring circuit diagrams of system, wiring destination schedules for circuits and replacement part numbers. Manuals to include as-built cable Project site plot plans and floor plans indicating cables, both underground and in each building with conduit, and as-built coding used on cables. Submit programming forms of systems with complete information.

.5 Verify conduit for line voltage wires enters panel in line voltage areas and conduit for low-voltage control wires enters panel on low-voltage areas. Refer to manufacturer's plans and approved shop drawings for location of line and low- voltage areas. Verify with lighting control manufacturer catalogue information and specific product acceptability.

.6 Test low voltage cable for integrity and proper operation prior to turn over. Verify with system manufacturer all wiring and testing requirements.

.7 Locate panels so that they are readily accessible and not exposed to physical damage.


.8 Furnish panel locations with sufficient working space around panels to comply with the Canadian Electrical Code.

.9 Securely fasten panels to the mounting surface by at least four (4) points. Fastener to Section 26 05 29.

.10 Unused openings in the cabinet must be effectively closed.

.11 Ground cabinets as specified in the Canadian Electrical Code.

.12 Lugs to be suitable and listed for installation with the conductor being connected.

.13 Maintain conductor lengths to a minimum within the wiring gutter space. Leave conductors long enough to reach the terminal location in a manner that avoids strain on the connecting lugs.

.14 Maintain the required bending radius of conductors inside cabinets.

.15 Clean cabinets of foreign material such as cement, plaster and paint.

.16 Distribute and arrange conductors neatly in the wiring gutters.

.17 Follow the manufacturer's torque values to tighten lugs.

.18 Before energizing the panelboard, the following steps shall be taken: .1 Retighten connections to the manufacturer's torque specifications. Verify that

required connections have been furnished. .2 Remove shipping blocks from component devices and the panel interior. .3 Remove debris from panelboard interior.

.19 Follow manufacturers' instructions for installation and all low voltage wiring.

.20 Provide the Consultant with report from lighting control system manufacturer/vender, detailing equipment setpoints, and all variations from designed operation, and all programming/access credentials required.

.21 The successful vendor must have a factory trained commissioning agent capable of complete programming of the lighting control system within a five (5) hour driving radius of the project site.

END OF SECTION

NSLC Select Store Roll-Out Section 26 52 01 NSL-057 Berwick – November 2020 EQUIPMENT FOR EMERGENCY LIGHTING Page 1 of 2

PART 1 - GENERAL




.3 Section 26 05 34 - Conduits, Conduit Fastenings and Fittings

1.2 PRODUCT DATA


.2 Data to indicate system components, mounting method, source of power and special attachments.


.1 Submit operation and maintenance data for incorporation in the Manual specified in Section 01 78 00 – Closeout Submittals.

PART 2 - PRODUCTS

2.1 BATTERY UNIT

.1 Supply voltage: 120Vac, or 347Vac as indicated.

.2 Output voltage: 12Vdc.

.3 Operating time: 30 min. based on actual DC load of connected remote heads.

.4 Battery: sealed, maintenance free, 10-year life warranty.

.5 Charger: solid state, multi-rate, voltage/current regulated, inverse temperature compensated, short circuit protected with regulated output of plus or minus 0.01 V for plus or minus 10% input variations.

.6 Solid state transfer circuit.

.7 Low voltage disconnect: solid state, modular, operates at 80% battery output voltage.

.8 Signal lights: LED solid state, for 'AC Power ON' and 'High Charge'.

.9 Lamp heads: integral on unit, 345 degree horizontal and 180-degree vertical adjustment. Lamp type: LED.

.10 Ceiling recessed or wall mounted as indicated on drawings.

NSLC Select Store Roll-Out Section 26 52 01 NSL-057 Berwick – November 2020 EQUIPMENT FOR EMERGENCY LIGHTING Page 2 of 2

.11 If recessed, install cabinets flush in t-bar or dry wall ceilings, with required mounting hardware based on the application.

.12 Finish: white.

.13 Auxiliary equipment: .1 Test switch. .2 Automatic Diagnostic circuitry.

2.2 REMOTE HEADS

.1 Supply voltage: 12 V dc from the battery pack.

.2 Wattage: 4W LED.

.3 Mounting: mounts directly onto standard octagon box supplied by contactor.

.4 Housing: 5” round canopy with two (2) 3” diameter heads. White in colour.

2.3 WIRING OF REMOTE HEADS

.1 Conduit: As specified in Section 26 05 34 - Conduits, Conduit Fastenings and Fittings.

.2 Conductors: minimum #12 AWG RW90 in conduit.

PART 3 - EXECUTION

3.1 INSTALLATION

.1 Install unit equipment and remote mounted fixtures as indicated.

.2 Direct heads as indicated.

.3 Make connections.

.4 Test and verify operation of units upon loss and restoration of normal ac power. Verify 30 min. battery life upon loss of power.

.5 Feed the emergency lighting system from the same circuit which feeds the normal lights in that area.

END OF SECTION

NSLC Select Store Roll-Out Section 26 53 00 NSL-057 Berwick – November 2020 EXIT LIGHTS Page 1 of 2

PART 1 - GENERAL




1.2 PRODUCT DATA



.1 Submit operation and maintenance data for incorporation in the Manual specified in Section 01 78 00 – Closeout Submittals.

1.4 REFERENCE

.1 CAN/CSA C860-11(R2016), Performance of Internally Lighted Exit Signs.

PART 2 - PRODUCTS

2.1 STANDARD UNITS

.1 Housing: steel, white finish.

.2 Face and back plates: steel.

.3 Lamps: One (1) LED-2W panel 120 VAC or 347 VAC, 219,000 h.

.4 Operation: designed for 219,000 h, LED panel only, 120V VAC or 347 VAC/12 VDC, 30-minute operating time after loss of AC power.

.5 Green running man pictogram style face.

.6 Face plate to remain captive for re-lamping.

.7 Unit to operate on 12 VD under emergency conditions.

.8 Mounting: Unit to have universal mounting position.

.9 Ten (10) year life warranty.

.10 Complete with automatic self-test feature (visual only).

NSLC Select Store Roll-Out Section 26 53 00 NSL-057 Berwick – November 2020 EXIT LIGHTS Page 2 of 2 PART 3 - EXECUTION

3.1 INSTALLATION

.1 Install exit lights.

.2 Connect fixtures to exit light circuits as indicated on the drawings.

.3 Confirm exit light circuit breaker is locked in on position.

END OF SECTION






Please note the following modifications to the specifications and drawings. Compliant bids shall be deemed to include these modifications. Specifications and Drawings: Please replace drawings M-100, M-200 and M-300 with the revised drawings attached.

Thank you, Tracey Darrigan, Procurement Manager

ABCEFG

1

2

3

C

OS

C

C

C

SP

CCC

C

C

C

C

E

OS

OS

C

OS

OS

OS

OS

TV

SP

SP

SP

SP

C C

8' - 0" A.F.F.

10' - 4" A.F.F.

10' - 0" A.F.F.

8' - 0" A.F.F.

10' - 0" A.F.F.

7'-11 3/4" A.F.F.7'-9 1/2" A.F.F.7'-9 1/2" A.F.F. 7'-11 3/4" A.F.F.

DEMOLITION - HVAC

1-

3/16"=1'-0"

SCALE:

PROJECT #:

DRAWN BY:

DRAWING #:

SEAL:

CLIENT:

PROJECT:

TITLE:

Breakhouse Architecture Inc. 2012C

NORTH ARROW:

ISSUED/REVISIONS:

Contact:

CBCL Limited1505 Barrington St,

Halifax, NS, B3J 3K5

T 902-421-7241

F 902-423-3938

www.cbcl.ca

NOVA SCOTIA LIQUORCORPORATION 93CHAIN LAKE DRIVEHALIFAX, NS, B3S 1A3

STEPHEN BAYERT. 902-450-5916F. 902-450-6116

BERWICK NSLC SELECTSTORE - INTERIORRENOVATION

200 COMMERCIAL ST,BERWICK, NS, B0P 1E0

MECHANICALDEMOLITION

CBCL

200613.06

AS NOTED

M-100

E

A

N

ER

R

TIS

EG

.

P

RE

C. J. RUDDICK

9056

I CV

AN

VONFOEC S

OIORPD

SSEF

DATE

O

ANL

I

O

T

NIE

ER

G.

AutoCAD SHX Text

CARTS

AutoCAD SHX Text

STRUCTURE ABOVE

AutoCAD SHX Text

MECH. RM

AutoCAD SHX Text

106

AutoCAD SHX Text

MENS' W/R

AutoCAD SHX Text

107

AutoCAD SHX Text

WOMEN'S W/R

AutoCAD SHX Text

108

AutoCAD SHX Text

JANITOR

AutoCAD SHX Text

109

AutoCAD SHX Text

WAREHOUSE

AutoCAD SHX Text

105

AutoCAD SHX Text

BEER COOLER

AutoCAD SHX Text

104

AutoCAD SHX Text

RETAIL SPACE

AutoCAD SHX Text

102

AutoCAD SHX Text

OFFICE

AutoCAD SHX Text

103

AutoCAD SHX Text

STAFF ROOM

AutoCAD SHX Text

110

AutoCAD SHX Text

VESTIBULE

AutoCAD SHX Text

101

AutoCAD SHX Text

OPEN TO U/S STRUCTURE

AutoCAD SHX Text


AutoCAD SHX Text


AutoCAD SHX Text

STRUCTURE ABOVE

AutoCAD SHX Text

26"x12"

AutoCAD SHX Text

20"x12"

AutoCAD SHX Text

26"x12"

AutoCAD SHX Text

14"x10"

AutoCAD SHX Text

12"x10"

AutoCAD SHX Text

12"x10"

AutoCAD SHX Text

12"

AutoCAD SHX Text

10"

AutoCAD SHX Text

10"

AutoCAD SHX Text

8"

AutoCAD SHX Text

EXISTING ROOF-MOUNTED SUPPLY FAN TO REMAIN.

AutoCAD SHX Text

EXISTING FAN-FORCED UNIT HEATER SERVING VESTIBULE TO BE REMOVED & REPLACED. PIPING TO REMAIN AS REQUIRED FOR CONNECTION TO NEW EQUIPMENT.

AutoCAD SHX Text

EXISTING UNIT-HEATER ABOVE CEILING AND ASSOCIATED GRILLE TO BE REMOVED. REMOVE & CAP PIPING BACK TO MAIN.

AutoCAD SHX Text

EXISTING ROUND CEILING DIFFUSER TO REMAIN. (TYP. 2)

AutoCAD SHX Text

EXISTING CEILING DIFFUSER TO BE REMOVED. ASSOCIATED DUCTWORK TO REMAIN AS REQUIRED FOR CONNECTION TO NEW DIFFUSER. (TYP. 8)

AutoCAD SHX Text

EXISTING WINDOW-MOUNTED AC UNIT TO BE REMOVED.

AutoCAD SHX Text

EXISTING R/A GRILLES TO BE REMOVED. (TYP. 6)

AutoCAD SHX Text

BRANCH DUCTWORK TO BE REMOVED AND CAPPED AT MAIN.

AutoCAD SHX Text

REMOVE EXISTING ROOFTOP AIR HANDLING UNIT. ROOF CURB TO REMAIN. PROTECT OPENINGS FROM WEATHER DURING CONSTRUCTION.

AutoCAD SHX Text

1-1/2"

AutoCAD SHX Text

3/4"

AutoCAD SHX Text

3/4"

AutoCAD SHX Text

1-1/2"

AutoCAD SHX Text

3/4"

AutoCAD SHX Text

3/4"

AutoCAD SHX Text

EXISTING WALL CAPS TO BE REMOVED AND REPLACED. SEE M-200.

AutoCAD SHX Text

EXISTING CEILING GRILLE TO BE REMOVED (2 TYP.)

AutoCAD SHX Text

EXISTING PERIMETER HYDRONIC HEATING CABINET TO BE REMOVED TO ALLOW FOR WALL REPAIR. PROTECT FROM DAMAGE AND REINSTALL WHEN REPAIRS ARE COMPLETED

AutoCAD SHX Text

EXISTING THERMOSTAT TO BE RELOCATED

AutoCAD SHX Text

T

AutoCAD SHX Text

EXISTING FAN COIL UNIT AND ASSOCIATED THERMOSTAT TO REMAIN. ALL ASSOCIATED DUCTWORK TO BE REMOVED. (TYP. 2)

AutoCAD SHX Text

EXISTING UNIT HEATER SERVING WAREHOUSE TO REMAIN. (TYP. 3)

AutoCAD SHX Text

T

AutoCAD SHX Text

%%UDWG. FILE LOCATION:

AutoCAD SHX Text

%%ULAYOUT:

AutoCAD SHX Text

\\cbcl.lan\cbcl\Halifax\Data\Projects\200613.06 NSLC BERWICK BWS\20 CAD\04 MECH\M-100 MECHANICAL REVISIONS.dwg

AutoCAD SHX Text

%%UDATE:

AutoCAD SHX Text

December 18, 2020 12:56:27 PM

AutoCAD SHX Text

M-100

AutoCAD SHX Text

No.

AutoCAD SHX Text

Remarks

AutoCAD SHX Text

Date

AutoCAD SHX Text

DO NOT SCALE THIS DRAWING FOR CONSTRUCTION CONSTRUCTION PURPOSES. USE FIGURED DIMENSIONS AS NOTED. THESE DRAWINGS ARE TO BE READ IN CONJUNCTION WITH SPECIFICATIONS AND GENERAL CONTRACTUAL CONDITIONS. ALL DIMENSIONS AND CONDITIONS ARE TO BE VERIFIED ON SITE. ALL DISCREPANCIES ARE TO BE REPORTED TO THE ARCHITECT AND AGREED UPON BEFORE PROCEEDING. THESE DRAWINGS ARE TO BE USED FOR THIS PROJECT ONLY AND SHALL NOT BE USED FOR ANY OTHER PURPOSE WITHOUT WRITTEN CONSENT OF THE ARCHITECT.

AutoCAD SHX Text

GENERAL NOTES:

AutoCAD SHX Text

CONSULTANTS:

AutoCAD SHX Text

A

AutoCAD SHX Text

B

AutoCAD SHX Text

C

AutoCAD SHX Text

D

AutoCAD SHX Text

4

AutoCAD SHX Text

2

AutoCAD SHX Text

1

AutoCAD SHX Text

3

AutoCAD SHX Text

MECHANICAL & ELECTRICAL:

AutoCAD SHX Text

01

AutoCAD SHX Text

2020.10.16

AutoCAD SHX Text

ISSUED FOR REVIEW

AutoCAD SHX Text

02

AutoCAD SHX Text

2020.11.27

AutoCAD SHX Text

03

AutoCAD SHX Text

2020.12.18

AutoCAD SHX Text

ISSUED FOR TENDER

AutoCAD SHX Text

ADDENDUM NO.1

AutoCAD SHX Text

1

AutoCAD SHX Text

Dec 18, 2020

ABCEFG

1

2

3

NEW CONSTRUCTION - HVAC

1-

3/16"=1'-0"

SCALE:

PROJECT #:

DRAWN BY:

DRAWING #:

SEAL:

CLIENT:

PROJECT:

TITLE:


NORTH ARROW:

ISSUED/REVISIONS:

Contact:



T 902-421-7241

F 902-423-3938

www.cbcl.ca


STEPHEN BAYERT. 902-450-5916F. 902-450-6116



MECHANICAL NEWCONSTRUCTION

CBCL

200613.06

AS NOTED

M-200

E

A

N

ER

R

TIS

EG

.

P

RE

C. J. RUDDICK

9056

I CV

AN

VONFOEC S

OIORPD

SSEF

DATE

O

ANL

I

O

T

NIE

ER

G.

AutoCAD SHX Text

WALL HEATER

AutoCAD SHX Text

26"x12"

AutoCAD SHX Text

20"x12"

AutoCAD SHX Text

26"x12"

AutoCAD SHX Text

14"x10"

AutoCAD SHX Text

12"x10"

AutoCAD SHX Text

12"x10"

AutoCAD SHX Text

12"

AutoCAD SHX Text

10"

AutoCAD SHX Text

10"

AutoCAD SHX Text

1-1/2"

AutoCAD SHX Text

1-1/2"

AutoCAD SHX Text

3/4"

AutoCAD SHX Text

3/4"

AutoCAD SHX Text

T

AutoCAD SHX Text

BPB-1

AutoCAD SHX Text

NEW BYPASS BOX C/W 2KW ELECTRIC REHEAT COIL

AutoCAD SHX Text

T

AutoCAD SHX Text

200

AutoCAD SHX Text

S-1

AutoCAD SHX Text

EVAP-1

AutoCAD SHX Text

COND-1

AutoCAD SHX Text

FFUH-1

AutoCAD SHX Text

150

AutoCAD SHX Text

S-1

AutoCAD SHX Text

310

AutoCAD SHX Text

S-1

AutoCAD SHX Text

310

AutoCAD SHX Text

S-1

AutoCAD SHX Text

310

AutoCAD SHX Text

S-1

AutoCAD SHX Text

310

AutoCAD SHX Text

S-1

AutoCAD SHX Text

310

AutoCAD SHX Text

S-1

AutoCAD SHX Text

310

AutoCAD SHX Text

S-1

AutoCAD SHX Text

-

AutoCAD SHX Text

R-1

AutoCAD SHX Text

-

AutoCAD SHX Text

R-1

AutoCAD SHX Text

-

AutoCAD SHX Text

R-1

AutoCAD SHX Text

-

AutoCAD SHX Text

R-1

AutoCAD SHX Text

-

AutoCAD SHX Text

R-1

AutoCAD SHX Text

NEW 24X24 DIFFUSER. SEE SCHEDULE ON DWG M-300. CONNECT TO EXISTING DUCTWORK. (TYP. 9) COORDINATE EXACT LOCATIONS W/ ARCHITECTURAL RCP.

AutoCAD SHX Text

ROUTE NEW 1" CONDENSATE PIPING FROM EVAP-1 THROUGH EXTERIOR WALL DOWN TO GRADE. SLOPE PIPING IN DIRECTION OF FLOW.

AutoCAD SHX Text

NEW THERMOSTAT MOUNTED AT 5'-0" A.F.F

AutoCAD SHX Text

SUPPORT EXTERIOR CONDENSING UNIT w/ STAINLESS STEEL BRACKETS SECURED TO WALL

AutoCAD SHX Text

NEW 24X24 R/A GRILLE. (TYP. 7) SEE SCHEDULE ON DWG M-300.

AutoCAD SHX Text

EXISTING ROOF CURB AND DUCTWORK TO REMAIN. INSTALL ADAPTOR CURB TO SUIT C/W FASTENERS, FLASHING, AND SEALS TO ENSURE A WATERTIGHT CONNECTION IN ACCORDANCE WITH SMACNA AND AHU MANUFACTURER'S INSTRUCTIONS

AutoCAD SHX Text

HVAC NOTES: 1. AIRFLOW VALUES INDICATED ON DRAWING IS BASED ON EXISTING DESIGN DRAWINGS. AIRFLOW VALUES INDICATED ON DRAWING IS BASED ON EXISTING DESIGN DRAWINGS. 2. AIR BALANCING CONTRACTOR TO BALANCE AIRFLOWS TO THE VALUES INDICATED. NOTIFY ENGINEER OF ANY DISCREPANCIES. AIR BALANCING CONTRACTOR TO BALANCE AIRFLOWS TO THE VALUES INDICATED. NOTIFY ENGINEER OF ANY DISCREPANCIES. 3. COORDINATE DIFFUSER LOCATION WITH ELECTRICAL LIGHT FIXTURES PRIOR TO ROUGH-IN. CONFIRM LOCATION WITH THE OWNER'S COORDINATE DIFFUSER LOCATION WITH ELECTRICAL LIGHT FIXTURES PRIOR TO ROUGH-IN. CONFIRM LOCATION WITH THE OWNER'S SITE REPRESENTATIVE PRIOR TO COMMENCEMENT OF WORK.

AutoCAD SHX Text

AHU-1

AutoCAD SHX Text

75

AutoCAD SHX Text

S-1

AutoCAD SHX Text

BB-1

AutoCAD SHX Text

NEW BASEBOARD HEATER. SEE SCHEDULE ON M-300. COORDINATE EXACT LOCATION WITH MILLWORK.

AutoCAD SHX Text

CONNECT TO EXISTING 1-1/2" TAKEOFFS. INSULATE NEW BRANCH PIPING TO BB-1

AutoCAD SHX Text

CONNECT TO EXISTING SUPPLY DUCTWORK

AutoCAD SHX Text

PROVIDE NEW WALL CAPS FOR WASHROOMS AND JANITOR'S CLOSET (3 TYP.), BLACK IN COLOR. SIZE MATCH EXISTING DUCT DIMENSIONS.

AutoCAD SHX Text


AutoCAD SHX Text

-

AutoCAD SHX Text

R-2

AutoCAD SHX Text

-

AutoCAD SHX Text

R-2

AutoCAD SHX Text

T

AutoCAD SHX Text

RELOCATED THERMOSTAT FOR PERIMETER HEATING

AutoCAD SHX Text

REINSTALL PERIMETER HYDRONIC HEATER AFTER WALL REPAIRS HAVE BEEN COMPLETED.

AutoCAD SHX Text

T

AutoCAD SHX Text

NEW HYDRONIC FAN-FORCED UNIT HEATER. SEE SCHEDULE ON DWG M-300. CONNECT TO EXISTING PIPING. SEE DETAIL 5, DWG. M-300

AutoCAD SHX Text

NEW AHU-1 CONTROLLER

AutoCAD SHX Text

T

AutoCAD SHX Text

T

AutoCAD SHX Text

MOUNTED IN TBAR (SEE NOTE 3)

AutoCAD SHX Text

NEW EXHAUST FAN EF-1

AutoCAD SHX Text

NEW 12x12 EXHAUST DUCT C/W FIRE DAMPER

AutoCAD SHX Text

T

AutoCAD SHX Text

-

AutoCAD SHX Text

E-2

AutoCAD SHX Text

NEW LOW VOLTAGE REVERSE ACTING THERMOSTAT

AutoCAD SHX Text

NEW HOT WATER COIL SIZED TO MATCH DUCT. 60 MBH @ 180°F EWT, 160°F LWT, 6 GPM. COPPER TUBE, ALUMINUM FIN. ENGINEERED AIR OR EQUAL.

AutoCAD SHX Text

NEW 1" HWS/HWR. TIE BACK TO EXISTING MAINS IN BOILER ROOM. SEE DUCT COIL PIPING DETAIL.

AutoCAD SHX Text

-

AutoCAD SHX Text

S-5

AutoCAD SHX Text

-

AutoCAD SHX Text

S-5

AutoCAD SHX Text

CONNECT TO EXISTING 1-1/2" HWR PIPING

AutoCAD SHX Text

CONNECT TO EXISTING 1-1/2" HWS PIPING.

AutoCAD SHX Text


AutoCAD SHX Text

%%ULAYOUT:

AutoCAD SHX Text

\\cbcl.lan\cbcl\Halifax\Data\Projects\200613.06 NSLC BERWICK BWS\20 CAD\04 MECH\M-200 MECHANICAL NEW CONSTRUCTION.dwg

AutoCAD SHX Text

%%UDATE:

AutoCAD SHX Text

December 18, 2020 1:15:45 PM

AutoCAD SHX Text

M-200 MECHANICAL NEW CONSTRUCTION

AutoCAD SHX Text

No.

AutoCAD SHX Text

Remarks

AutoCAD SHX Text

Date

AutoCAD SHX Text


AutoCAD SHX Text

GENERAL NOTES:

AutoCAD SHX Text

CONSULTANTS:

AutoCAD SHX Text

A

AutoCAD SHX Text

B

AutoCAD SHX Text

C

AutoCAD SHX Text

D

AutoCAD SHX Text

4

AutoCAD SHX Text

2

AutoCAD SHX Text

1

AutoCAD SHX Text

3

AutoCAD SHX Text


AutoCAD SHX Text

01

AutoCAD SHX Text

2020.10.16

AutoCAD SHX Text

ISSUED FOR REVIEW

AutoCAD SHX Text

02

AutoCAD SHX Text

2020.11.27

AutoCAD SHX Text

03

AutoCAD SHX Text

2020.12.18

AutoCAD SHX Text

ISSUED FOR TENDER

AutoCAD SHX Text

ADDENDUM NO.1

AutoCAD SHX Text

1

AutoCAD SHX Text

Dec 18, 2020

SCALE:

PROJECT #:

DRAWN BY:

DRAWING #:

SEAL:

CLIENT:

PROJECT:

TITLE:


NORTH ARROW:

ISSUED/REVISIONS:

Contact:



T 902-421-7241

F 902-423-3938

www.cbcl.ca


STEPHEN BAYERT. 902-450-5916F. 902-450-6116



MECHANICAL DETAILS& SCHEDULES

CBCL

200613.06

AS NOTED

M-300

E

A

N

ER

R

TIS

EG

.

P

RE

C. J. RUDDICK

9056

I CV

AN

VONFOEC S

OIORPD

SSEF

DATE

O

ANL

I

O

T

NIE

ER

G.

AutoCAD SHX Text


AutoCAD SHX Text

%%ULAYOUT:

AutoCAD SHX Text

\\cbcl.lan\cbcl\Halifax\Data\Projects\200613.06 NSLC BERWICK BWS\20 CAD\04 MECH\M-300 MECHANICAL DETAILS & SCHEDULES.dwg

AutoCAD SHX Text

%%UDATE:

AutoCAD SHX Text

December 18, 2020 1:42:09 PM

AutoCAD SHX Text

M-300 MECHANICAL DETAILS & SCHEDULES

AutoCAD SHX Text

No.

AutoCAD SHX Text

Remarks

AutoCAD SHX Text

Date

AutoCAD SHX Text


AutoCAD SHX Text

GENERAL NOTES:

AutoCAD SHX Text

CONSULTANTS:

AutoCAD SHX Text

A

AutoCAD SHX Text

B

AutoCAD SHX Text

C

AutoCAD SHX Text

D

AutoCAD SHX Text

4

AutoCAD SHX Text

2

AutoCAD SHX Text

1

AutoCAD SHX Text

3

AutoCAD SHX Text


AutoCAD SHX Text

01

AutoCAD SHX Text

2020.10.16

AutoCAD SHX Text

ISSUED FOR REVIEW

AutoCAD SHX Text

02

AutoCAD SHX Text

2020.11.27

AutoCAD SHX Text

03

AutoCAD SHX Text

2020.12.18

AutoCAD SHX Text

ISSUED FOR TENDER

AutoCAD SHX Text

ADDENDUM NO.1

AutoCAD SHX Text

GRILLE & DIFFUSER SCHEDULE

AutoCAD SHX Text

DESIG.

AutoCAD SHX Text

TYPE

AutoCAD SHX Text

MFGR.

AutoCAD SHX Text

MODEL

AutoCAD SHX Text

SIZE

AutoCAD SHX Text

NECK

AutoCAD SHX Text

COMMENTS

AutoCAD SHX Text

S-1

AutoCAD SHX Text

ROUND CEILING DIFFUSER

AutoCAD SHX Text

NAILOR

AutoCAD SHX Text

RBD

AutoCAD SHX Text

-

AutoCAD SHX Text

250

AutoCAD SHX Text

SPUN ALUMINUM, WHITE FINISH, INTEGRAL BALANCING DAMPER

AutoCAD SHX Text

S-2

AutoCAD SHX Text

SQUARE SUPPLY GRILLE

AutoCAD SHX Text

NAILOR

AutoCAD SHX Text

67SH

AutoCAD SHX Text

250x250

AutoCAD SHX Text

-

AutoCAD SHX Text

304 STAINLESS STEEL, SINGLE DEFLECTION, INTEGRAL BALANCING DAMPER

AutoCAD SHX Text

S-3

AutoCAD SHX Text

SQUARE CEILING DIFFUSER

AutoCAD SHX Text

NAILOR

AutoCAD SHX Text

RNS

AutoCAD SHX Text

300x300

AutoCAD SHX Text

150

AutoCAD SHX Text

HEAVY GAUGE STEEL, WHITE FINISH, LAY-IN T-BAR

AutoCAD SHX Text

S-4

AutoCAD SHX Text


AutoCAD SHX Text

NAILOR

AutoCAD SHX Text

RNS

AutoCAD SHX Text

600x600

AutoCAD SHX Text

250

AutoCAD SHX Text


AutoCAD SHX Text

S-5

AutoCAD SHX Text


AutoCAD SHX Text

NAILOR

AutoCAD SHX Text

RNS

AutoCAD SHX Text

600x600

AutoCAD SHX Text

360

AutoCAD SHX Text


AutoCAD SHX Text

R-1

AutoCAD SHX Text

EGGCRATE GRILLE

AutoCAD SHX Text

NAILOR

AutoCAD SHX Text

51EC

AutoCAD SHX Text

600x600

AutoCAD SHX Text

-

AutoCAD SHX Text

ALUMINUM CORE / FRAME, WHITE FINISH, LAY-IN T-BAR

AutoCAD SHX Text

E-1

AutoCAD SHX Text

FIXED BLADE GRILLE

AutoCAD SHX Text

NAILOR

AutoCAD SHX Text

5145

AutoCAD SHX Text

150x150

AutoCAD SHX Text

-

AutoCAD SHX Text

ALUMINUM BAR GRILLE, WHITE FINISH, INTEGRAL BALANCING DAMPER

AutoCAD SHX Text

E-2

AutoCAD SHX Text

FIXED BLADE GRILLE

AutoCAD SHX Text

NAILOR

AutoCAD SHX Text

5145

AutoCAD SHX Text

300x300

AutoCAD SHX Text

-

AutoCAD SHX Text

ALUMINUM BAR GRILLE, WHITE FINISH

AutoCAD SHX Text

BYPASS BOX SCHEDULE

AutoCAD SHX Text

DESIG.

AutoCAD SHX Text

MFGR.

AutoCAD SHX Text

MODEL

AutoCAD SHX Text

INLET DIAMETER (in.)

AutoCAD SHX Text

MAX CAPACITY (CFM)

AutoCAD SHX Text

COMMENTS

AutoCAD SHX Text

BPB-1

AutoCAD SHX Text

NAILOR

AutoCAD SHX Text

D34RE

AutoCAD SHX Text

6"

AutoCAD SHX Text

0-400

AutoCAD SHX Text

ANALOG BYPASS BOX, SEQUENCE OF OPERATIONS 'E6': AUTOMATIC HEATING / COOLING CHANGEOVER WITH PROPORTIONAL ELECTRIC HEAT, 2 KW @ 208/1/60, LOW VOLTAGE ACTUATOR, WALL-MOUNTED THERMOSTAT, 120V w/ INTEGRAL TRANSFORMER. SET MIN. POSITION TO 20%.

AutoCAD SHX Text

SPLIT SYSTEM HEAT PUMP SCHEDULE

AutoCAD SHX Text

DESIG.

AutoCAD SHX Text

LOCATION

AutoCAD SHX Text

MANUFACTURER

AutoCAD SHX Text

MODEL

AutoCAD SHX Text

REFRIGERANT

AutoCAD SHX Text

NOMINAL CAPACITY

AutoCAD SHX Text

HEATING

AutoCAD SHX Text

COOLING

AutoCAD SHX Text

AIR FLOW

AutoCAD SHX Text

POWER

AutoCAD SHX Text

UNIT MCA

AutoCAD SHX Text

COMMENTS

AutoCAD SHX Text

EVAP-1

AutoCAD SHX Text

OFFICE 103

AutoCAD SHX Text

MITSUBISHI

AutoCAD SHX Text

MSZ-GL12NA-U1

AutoCAD SHX Text

R410A

AutoCAD SHX Text

1 TON

AutoCAD SHX Text

12000 Btu/h

AutoCAD SHX Text

14400 Btu/h

AutoCAD SHX Text

237

AutoCAD SHX Text

208/1/60

AutoCAD SHX Text

1

AutoCAD SHX Text

c/w WIRED WALL CONTROLLER.

AutoCAD SHX Text

COND-1

AutoCAD SHX Text

OUTDOOR SECTION

AutoCAD SHX Text

MITSUBISHI

AutoCAD SHX Text

MUZ-GL12NA

AutoCAD SHX Text

R410A

AutoCAD SHX Text

1 TON

AutoCAD SHX Text

-

AutoCAD SHX Text

-

AutoCAD SHX Text

-

AutoCAD SHX Text

208/1/60

AutoCAD SHX Text

9

AutoCAD SHX Text

L

AutoCAD SHX Text

W L = 1/4 OF "W"

AutoCAD SHX Text

AIRFLOW

AutoCAD SHX Text

45°

AutoCAD SHX Text

2

AutoCAD SHX Text

-

AutoCAD SHX Text

TYPICAL DIFFUSER

AutoCAD SHX Text

DETAIL-

AutoCAD SHX Text

N.T.S.

AutoCAD SHX Text

3

AutoCAD SHX Text

-

AutoCAD SHX Text

TYP. TAKE-OFF BOOT ON SUPPLY TO DIFFUSER

AutoCAD SHX Text

DETAIL-

AutoCAD SHX Text

N.T.S.

AutoCAD SHX Text

NOTE: FLEX DUCT SHALL NOT BE USED ON BRANCH DUCTING TO DIFFUSERS IN ROOMS WITHOUT CEILINGS.

AutoCAD SHX Text

S/A

AutoCAD SHX Text

EYE SCREW

AutoCAD SHX Text

#12 WIRE

AutoCAD SHX Text

RIGID DUCT ELBOW

AutoCAD SHX Text

CEILING DIFFUSER SEE PLANS & SCHEDULE

AutoCAD SHX Text

CONNECT FLEXIBLE DUCT TO COLLAR WITH 22 GAUGE CLAMP & FOUR SHEET METAL SCREWS & SEAL WITH DUCT TAPE

AutoCAD SHX Text

CEILING

AutoCAD SHX Text

MINIMUM RADIUS EQUAL TO ONE DUCT DIAMETER

AutoCAD SHX Text

FLEXIBLE DUCT, SEE PLANS FOR SIZE

AutoCAD SHX Text

25MM X 22 GAUGE BAND

AutoCAD SHX Text

BALANCING DAMPER, TYPICAL

AutoCAD SHX Text

W

AutoCAD SHX Text

L = 1/4 OF "W"

AutoCAD SHX Text

L

AutoCAD SHX Text

45%%D

AutoCAD SHX Text

AIR FLOW

AutoCAD SHX Text

MAIN

AutoCAD SHX Text

DUCT

AutoCAD SHX Text

SUPPLIED WITH BOX

AutoCAD SHX Text

ATTENUATOR

AutoCAD SHX Text

TIMES INLET DIA.

AutoCAD SHX Text

LENGTH TO BE 2

AutoCAD SHX Text

RIGID ROUND DUCT

AutoCAD SHX Text

ACTUATOR

AutoCAD SHX Text

AS REQUIRED.

AutoCAD SHX Text

DISCHARGE DUCT SIZE

AutoCAD SHX Text

B.D.

AutoCAD SHX Text

ACCESS PANEL

AutoCAD SHX Text

ELECTRONIC

AutoCAD SHX Text

MIN. 2 TIMES DUCT WIDTH.

AutoCAD SHX Text

4

AutoCAD SHX Text

-

AutoCAD SHX Text

N.T.S.

AutoCAD SHX Text

TYP. BYPASS BOX TERMINAL UNIT CONNECTION

AutoCAD SHX Text

DETAIL-

AutoCAD SHX Text

FORCE FLOW HEATER SCHEDULE

AutoCAD SHX Text

DESIG.

AutoCAD SHX Text

MANUFACTURER

AutoCAD SHX Text

MODEL

AutoCAD SHX Text

ARRANGEMENT

AutoCAD SHX Text

HEAT OUTPUT

AutoCAD SHX Text

EWT

AutoCAD SHX Text

LWT

AutoCAD SHX Text

AIRFLOW

AutoCAD SHX Text

MOTOR POWER

AutoCAD SHX Text

COMMENTS

AutoCAD SHX Text

FFUH-1

AutoCAD SHX Text

AIRTEX

AutoCAD SHX Text

CUH SERIES

AutoCAD SHX Text

19

AutoCAD SHX Text

47 MBH

AutoCAD SHX Text

180 F

AutoCAD SHX Text

160 F

AutoCAD SHX Text

620 CFM

AutoCAD SHX Text

120V/1

AutoCAD SHX Text

SEMI-RECESSED MODEL, INTEGRAL THERMOSTAT, UNIT DIMENSIONS TO SUIT ROUGH OPENING OF EXISTING (35" H x 45" W). DETERMINE EXACT DIMENSIONS ONSITE PRIOR TO ORDER

AutoCAD SHX Text

5

AutoCAD SHX Text

-

AutoCAD SHX Text

FORCE FLOW CABINET HEATER PIPING

AutoCAD SHX Text

DETAIL-

AutoCAD SHX Text

N.T.S.

AutoCAD SHX Text

WALL HUNG FULLY RECESSED CABINET

AutoCAD SHX Text

FRONT INLET

AutoCAD SHX Text

OUTLINE OF COIL AND FILTER SECTION

AutoCAD SHX Text

FRONT DISCHARGE

AutoCAD SHX Text

EXISTING ISOLATION VALVES

AutoCAD SHX Text

UNION

AutoCAD SHX Text

20mm HOSE BIBB

AutoCAD SHX Text

BASEBOARD HEATER SCHEDULE

AutoCAD SHX Text

DESIG.

AutoCAD SHX Text

SERVICE

AutoCAD SHX Text

MANUFACTURER

AutoCAD SHX Text

MODEL

AutoCAD SHX Text

ROWS

AutoCAD SHX Text

HEATING OUTPUT (PER FT)

AutoCAD SHX Text

ELEMENT LENGTH (FT)

AutoCAD SHX Text

EWT

AutoCAD SHX Text

LWT

AutoCAD SHX Text

EAT

AutoCAD SHX Text

COMMENTS

AutoCAD SHX Text

BB-1

AutoCAD SHX Text

HEATING

AutoCAD SHX Text

ENGINEERED AIR

AutoCAD SHX Text

PROFILE SERIES (P-10)

AutoCAD SHX Text

1

AutoCAD SHX Text

637 BTU

AutoCAD SHX Text

14

AutoCAD SHX Text

160

AutoCAD SHX Text

140

AutoCAD SHX Text

65

AutoCAD SHX Text

COPPER TUBE, ALUMINUM FIN, PAINTED STEEL CABINET WITH END CAPS AND MOUNTING BRACKET

AutoCAD SHX Text

8

AutoCAD SHX Text

-

AutoCAD SHX Text

BASEBOARD RADIATION PIPING

AutoCAD SHX Text

DETAIL-

AutoCAD SHX Text

N.T.S.

AutoCAD SHX Text

X

AutoCAD SHX Text

D

AutoCAD SHX Text

H

AutoCAD SHX Text

D

AutoCAD SHX Text

T

AutoCAD SHX Text

SEQUENCE OF OPERATION: 1. UNIT TO RECEIVE ITS OWN INDIVIDUAL FULLY MODIFIABLE UNIT TO RECEIVE ITS OWN INDIVIDUAL FULLY MODIFIABLE SCHEDULE COMPLETE WITH NIGHT-TIME SETBACK. COORDINATE SCHEDULE PROGRAMMING WITH OWNER. 2. OCCUPIED MODE: UNIT SHALL MODULATE/STAGE THE HEATING OCCUPIED MODE: UNIT SHALL MODULATE/STAGE THE HEATING AND COOLING SECTIONS TO MAINTAIN SPACE TEMPERATURE SET POINT. 3. UNOCCUPIED MODE: UNIT SHALL BE NORMALLY OFF AND SHALL UNOCCUPIED MODE: UNIT SHALL BE NORMALLY OFF AND SHALL BE ENERGIZED TO MAINTAIN SET POINT. 4. VENTILATION: PROVIDE DEMAND CONTROL VENTILATION (DCV) VENTILATION: PROVIDE DEMAND CONTROL VENTILATION (DCV) SEQUENCE FOR ECONOMIZER CONTROL BASED ON RETURN AIR CO . SET POINT: 1200 PPM. 2. SET POINT: 1200 PPM. 5. COOLING: DX COOLING SHALL STAGE AS REQUIRED TO ACHIEVE COOLING: DX COOLING SHALL STAGE AS REQUIRED TO ACHIEVE SPACE TEMPERATURE SET POINT. ECONOMIZER COOLING TO BE ENABLED AND CONTROLLED WHEN OUTDOOR AIR TEMPERATURE PERMITS AND SHALL OVERRIDE DX COOLING. 6. HEATING: PRIMARY HEATING SHALL BE PROVIDED BY THE HEAT HEATING: PRIMARY HEATING SHALL BE PROVIDED BY THE HEAT PUMP WITH A SUPPLEMENTAL ELECTRIC COIL PROVIDING A SECOND STAGE OF HEATING AS REQUIRED. THIRD STAGE TO BE BY COIL HC-1; MODULATE CONTROL VALVE AS REQUIRED.

AutoCAD SHX Text

6

AutoCAD SHX Text

-

AutoCAD SHX Text

N.T.S.

AutoCAD SHX Text

AHU-1 CONTROLS

AutoCAD SHX Text

DETAIL-

AutoCAD SHX Text

ADAPTOR

AutoCAD SHX Text

6"

AutoCAD SHX Text

8"

AutoCAD SHX Text

DRAIN PLUG

AutoCAD SHX Text

AIR HANDLING UNIT OR AIR CONDITIONING UNIT

AutoCAD SHX Text

REMOVABLE PLUG

AutoCAD SHX Text

COOLING COIL DRAIN PAN SECTION

AutoCAD SHX Text

1-1/4" PVC PIPE

AutoCAD SHX Text

NOTE: : CONFIRM TRAP DEPTHS WITH AHU MANUFACTURER.

AutoCAD SHX Text

7

AutoCAD SHX Text

-

AutoCAD SHX Text

N.T.S.

AutoCAD SHX Text

CONDENSATE DRAIN (TYP.)

AutoCAD SHX Text

DETAIL-

AutoCAD SHX Text

AHU-1

AutoCAD SHX Text

NOTE: MATCH EXISTING HEATER DIMENSIONS WHERE POSSIBLE. PROVIDE INFILL PANEL AS REQUIRED WITH INFILL DETAIL REVIEWED AND APPROVED BY ARCHITECT.

AutoCAD SHX Text

DRAIN VALVE

AutoCAD SHX Text

ECCENTRIC REDUCER

AutoCAD SHX Text

ELEMENT

AutoCAD SHX Text

TYP. (IF REQ'D)

AutoCAD SHX Text

RETURN

AutoCAD SHX Text

BALANCING VALVE

AutoCAD SHX Text

CONTROL VALVE

AutoCAD SHX Text

ISOLATION VALVE

AutoCAD SHX Text

AIR HANDLING UNIT SCHEDULE

AutoCAD SHX Text

TAG

AutoCAD SHX Text

TYPE

AutoCAD SHX Text

LOCATION

AutoCAD SHX Text

MAKE

AutoCAD SHX Text

MODEL NUMBER

AutoCAD SHX Text

TOTAL COOLING CAPACITY (MBH)

AutoCAD SHX Text

HP HEATING CAPACITY (MBH)

AutoCAD SHX Text

ELECTRIC HEATING COIL (KW)

AutoCAD SHX Text

AIRFLOW (CFM)

AutoCAD SHX Text

E.S.P. (IN)

AutoCAD SHX Text

POWER SUPPLY (V/HZ/PH)

AutoCAD SHX Text

MCA (AMP)

AutoCAD SHX Text

MOCP (AMP)

AutoCAD SHX Text

REFRIGERANT TYPE

AutoCAD SHX Text

REMARKS

AutoCAD SHX Text

AHU-1

AutoCAD SHX Text

HEAT PUMP

AutoCAD SHX Text

ROOF

AutoCAD SHX Text

YORK

AutoCAD SHX Text

XXEA7A2C3AA1B111A2

AutoCAD SHX Text

70.8

AutoCAD SHX Text

40.9

AutoCAD SHX Text

16.0

AutoCAD SHX Text

2400.0

AutoCAD SHX Text

1.7

AutoCAD SHX Text

208/3/60

AutoCAD SHX Text

75.8

AutoCAD SHX Text

80

AutoCAD SHX Text

R-410A

AutoCAD SHX Text

C/W ADAPTOR CURB (90 DEG), ECONOMIZER, HIGH STATIC DRIVE, TWO STAGE COMPRESSOR, VFD SUPPLY FAN, FIELD MOUNTED CO2 RETURN AIR SENSOR AND DCV CONTROLLER.

AutoCAD SHX Text

BALANCING VALVE

AutoCAD SHX Text

CONTROL VALVE

AutoCAD SHX Text

EXHAUST FAN SCHEDULE

AutoCAD SHX Text

DESIG.

AutoCAD SHX Text

LOCATION

AutoCAD SHX Text

MANUFACTURER

AutoCAD SHX Text

MODEL

AutoCAD SHX Text

AIR FLOW

AutoCAD SHX Text

STATIC PRESSURE

AutoCAD SHX Text

SPEED CONTROL

AutoCAD SHX Text

DISC SWITCH

AutoCAD SHX Text

ELECTRICAL

AutoCAD SHX Text

COMMENTS

AutoCAD SHX Text

EF-1

AutoCAD SHX Text

ELECTRICAL ROOM

AutoCAD SHX Text

LOREN COOK

AutoCAD SHX Text

GC-622

AutoCAD SHX Text

460 CFM

AutoCAD SHX Text

0.25 in.-wg.

AutoCAD SHX Text

YES

AutoCAD SHX Text

YES

AutoCAD SHX Text

120V/1PH/60HZ

AutoCAD SHX Text

CABINET FAN c/w RUBBER VIBRATION ISOLATORS, WHITE GRILLE, INSULATED HOUSING & ISOLATORS.

AutoCAD SHX Text

1

AutoCAD SHX Text

1

AutoCAD SHX Text

1

AutoCAD SHX Text

1

AutoCAD SHX Text

1

AutoCAD SHX Text

1

AutoCAD SHX Text

1

AutoCAD SHX Text

HWR TO HEATING MAIN

AutoCAD SHX Text

NEW 2-WAY VALVE

AutoCAD SHX Text

HWS FROM HEATING MAIN

AutoCAD SHX Text

NOTE: LOCATE CONTROL VALVE AND TRIM ADJACENT TO HEATING COIL UNIT. ENSURE VALVE ASSEMBLY IS ACCESSIBLE.

AutoCAD SHX Text

CBV

AutoCAD SHX Text

HOSE END DRAIN VALVE

AutoCAD SHX Text

PG

AutoCAD SHX Text

T

AutoCAD SHX Text

T

AutoCAD SHX Text

PG

AutoCAD SHX Text

AIR VENT

AutoCAD SHX Text

WATER HEATING COIL

AutoCAD SHX Text

BYPASS C/W N.C. GLOBE VALVE

AutoCAD SHX Text

1

AutoCAD SHX Text

-

AutoCAD SHX Text

N.T.S.

AutoCAD SHX Text

HEATING HOT WATER COIL PIPING (TYP.)

AutoCAD SHX Text

DETAIL-

AutoCAD SHX Text

1

AutoCAD SHX Text

1

AutoCAD SHX Text

PROVIDE DIGITAL AHU CONTROLLER KMC FLEXSTAT OR EQUIVALENT C/W PROGRAMMING TO SUIT SEQUENCE.

AutoCAD SHX Text

Dec 18, 2020

AutoCAD SHX Text

SUPPLY






Please note the following modifications to the specifications. Compliant bids shall be deemed to include these modifications. Specifications and Drawings: Please see attached for revisions to specifications and drawings. In addition, please also include the following updates for the Air Handling Unit AHU-1;

1. Reference drawing M300 - Remove the requirement for an integral disconnect switch

2. Remove the requirement for a convenience receptacle 3. Reference section 23 73 11 2.2.1 - Remove the requirement for SCR

electric heat. A single stage heater is acceptable. 4. Reference section 23 73 11 2.2.1 – Delete the requirement for double

wall construction. Single wall is acceptable 5. Reference 23 73 11 2.2.5 – Delete the requirements for 2” insulation.

½’ is acceptable. Bidders should note that GC will have responsibility for supply and install of the Sliding Automatic Entrance (D-07 on the door schedule). This was previously noted as Owner supplied.

Thank you, Tracey Darrigan, Procurement Manager

Specifications:

a. OMIT 1.6.1 Mandatory Walk-Through from Section 06 40 00 Architectural Woodwork b. REVISE: Section 08 42 29 – Sliding Automatic Entrances (attached) c. ADD: Section 27 05 13 – Structured Cabling for Communication Systems (attached) d. ADD: Section 27 05 28 – Telecommunications Raceway System (attached)

Architectural Drawings: 1. Reference Drawing A-002-R1 Schedule, & Phasing (attached)

a. REVISE D-07 to be supplied and installed by general contractor to supply and install sliding automatic entrance door and system to beer cooler. b. ADD phasing and notes

2. Drawing A-100 Demolition Plan a. NOTE Remove existing aluminum entrance sliding door to beer cooler and return to Client. Wrap and palletize, protect from damage. b. NOTE Remove existing steel angle bolted to floor in beer cooler, reinstall after resinous flooring installation.

3. Drawing A-101 Reflected Ceiling Plan – Demolition, NOTE existing beer cooler to remain. 4. Reference Drawing A-102-R1 Floor Plan (attached)

a. REVISE new power and comm feeds thru PAC pole at POS; refer to elec. b. REVISE POS dimensioned on plan, closer to vestibule c. REVISE Beer cooler sliding door position and reach in cooler door position. Flip layout per attached A-102-R1.

5. Drawing A-900-R1 Sign Plan and Schedule: (attached) a. ADD SN09 exterior sign specification to sign schedule. b. ADD SN10 perimeter valence signs to plan and specification to schedule.

6. Elevation C1/A-201 GRID-A REVISE new bollards to existing bollards. 7. Elevation B3/A-202 REVISE SN04 to WD-01 this wall, inside vestibule. Electrical Drawings: 1. Reference Drawing: E-103 – New Construction – Power and Telecom:

Addendum # 1 Date: 2020/12/15 Page: 1 of 2

Project: NSLC Berwick Renovation NSL-057 Phase: Tender Locations: 200 Commercial St, Berwick, NS B0P 1E0

This Addendum refers to changes and additions to the Original Contract Documents and is to be read in conjunction with same. All other parts of the Original Contract Documents are to be considered as applying to the Work of this Contract with the exceptions and changes noted below. The cost of this work shall be included in the Contract Price. All Clauses set forth in the General Conditions of the Original Contract Documents shall apply to and govern this Work. It is the responsibility of the Bidder to bring this addendum to the attention of all subcontractors and material suppliers.

a. PROVIDE connection to electrical room ceiling mounted exhaust fan ‘EF-1’ from 120V, 15A circuit ‘BP1-55’. ‘BP1-55’ previously noted as spare. Mark circuit “EF-1 – Electrical Room”. Refer to attached revised drawing E-103-R1 for location.

b. SUPPLY AND INSTALL one(1) rooftop mounted pedestal receptacle adjacent new AHU-1, receptacle fed from GFCI rated breaker. Refer to attached sketch ESK-01 for details.

c. REVISE note 7 as seen on attached revised drawing E-103-R1. d. Add note 15 as seen on attached revised drawing E-103-R1. Refer to attached sketch ESK-01 for

rooftop pedestal mounting structure and details. 2. Reference Drawing: M-200 – Mechanical New Construction:

a. SUPPLY AND INSTALL a new ceiling mounted exhaust fan controlled by a wall mounted low voltage reverse acting thermostat. Exhaust associated ductwork to be complete with fire damper as shown on attached revised drawing M-200-R1.

3. Reference Drawing: M-300 – Mechanical New Construction: a. REVISE Grill and Diffuser Schedule as seen on attached revised drawing M-300-R1. b. ADD Exhaust Fan Schedule as seen on attached revised drawing M-300-R1. c. REVISE motor voltage of FFUH-1 to be 120V, single phase.

End of Addendum #1

NSLC Berwick Store Renovation Section 08 42 29 NSL-057 Berwick - December 2020 SLIDING AUTOMATIC ENTRANCES Page 1 of 10 Part 1 General

1.1 RELATED REQUIREMENTS .1 Section 02 41 19 – Selective Demolition.

.2 Section 08 50 80 – Glazing.

1.2 REFERENCES .1 Aluminum Association (AA)

.1 DAF 45-03(R2009), Designation System for Aluminum Finishes.

.2 American Architectural Manufacturers Association (AAMA)

.1 AAMA 501-05, Methods of Test for Exterior Walls.

.2 AAMA 609-09, Cleaning and Maintenance Guide for Architecturally Finished Aluminum.

.3 AAMA 611-12, Specification for Anodized Architectural Aluminum.

.4 AAMA 701/702-04, Voluntary Specifications for Pile Weather Stripping and Replaceable Fenestration Weatherseals.

.5 AAMA 1503-09, Test Method for Thermal Transmittance and Condensation Resistance of Windows, Doors and Glazed Wall Sections.

.6 AAMA AFPA-91, Anodic Finishes/Painted Aluminum.

.7 AAMA CW-RS-1-04, The Rain Screen Principle and Pressure Equalized Wall Design.

.8 AAMA RPC-00, Rain Penetration Control: Applying Current Knowledge.

.3 American National Standards Institute (ANSI) / Builders Hardware Manufacturers Association (BHMA)

.1 ANSI/BHMA A156.10-2011, Power Operated Pedestrian Doors.

.2 ANSI/ BHMA A156.19-2013, Power Assist and Low Energy Power Operated Doors.

.4 American Society for Testing and Materials International, (ASTM)

.1 ASTM A653/A653M-15e1, Standard Specification for Steel Sheet, Zinc Coated (Galvanized) or Zinc Iron Alloy Coated (Galvannealed) by the Hot Dip Process.

.2 ASTM B209-14, Standard Specification for Aluminum and Aluminum-Alloy Sheet and Plate.

.3 ASTM B221/B221M-14, Standard Specification for Aluminum and Aluminum-Alloy Extruded Bars, Rods, Wire, Profiles, and Tubes.

.4 ASTM B429/B429M-10e1, Standard Specification for Aluminum-Alloy Extruded Structural Pipe and Tube.

.5 ASTM C920-14a, Standard Specification for Elastomeric Joint Sealants.

.6 ASTM D2000-12, Classification System for Rubber Products in Automotive Applications.

.7 ASTM D2287-12, Specification for Non-Rigid Vinyl Chloride Polymer and Copolymer Molding and Extrusion Compounds.

.8 ASTM E283-04(2012), Standard Test Method for Determining Rate of Air Leakage Through Exterior Windows, Curtain Walls, and Doors Under Specified Pressure Differences Across the Specimen.

.9 ASTM E330-14, Standard Test Method for Structural Performance of Exterior Windows, Doors, Skylights and Curtain Walls by Uniform Static Air Pressure Difference.

NSLC Berwick Store Renovation Section 08 42 29 NSL-057 Berwick - December 2020 SLIDING AUTOMATIC ENTRANCES Page 2 of 10

.10 ASTM E331-00(2009), Standard Test Method for Water Penetration of Exterior Windows, Skylights, Doors, and Curtain Walls by Uniform Static Air Pressure Difference.

.11 ASTM E547-00(2009), Standard Test Method for Water Penetration of Exterior Windows, Skylights, Doors, and Curtain Walls by Cyclic Static Air Pressure Difference.

.5 Canadian Standards Association (CSA International)

.1 CSA A440-11, NAFS - North American Fenestration Standard/Specification for Windows, Doors, and Skylights, Includes Update No. 1 (2014).

.2 CSA B651-12, Accessible Design for the Built Environment.

.3 CAN/CSA G40.20/G40.21-13, General Requirements for Rolled or Welded Structural Quality Steel/Structural Quality Steel.

.4 CAN/CSA G164-M92 (R2003), Hot Dip Galvanizing of Irregularly Shaped Articles.

.5 CSA W47.1-09(R2014), Certification of Companies for fusion Welding of Steel.

.6 CSA W47.2-11(R2015), Certification of Companies for Fusion Welding of Aluminum, Includes Update No. 1 (2011), Update No. 2 (2012).

.7 CSA W59-13, Welded Steel Construction (Metal Arc Welding), Includes Update No. 1 (2014).

.8 CSA W59.2-M1991 (R2013), Welded Aluminum Construction.

.6 The Society for Protective Coatings (SSPC)/National Association of Corrosion Engineers (NACE International)

.1 Surface Preparation Guidelines: .1 SSPC-SP COM Surface Preparation Commentary for Steel and

Concrete Substrates. .2 SSPC-PS Guide 12.00, Guide to Zinc-Rich Coating Systems.

.7 Underwriters' Laboratories of Canada (ULC)

.1 ULC C305-M1972, Panic Hardware.

.2 CAN/ULC S524-14, Standard for the Installation of Fire Alarm Systems.

.3 CAN/ULC S533-08, Egress Door Securing and Releasing Devices.

.8 Underwriters’ Laboratories

.1 UL 325, Door, Drapery, Gate, Louver, and Window Operators and Systems, dated 10/14/2013.

1.3 ACTION AND INFORMATIONAL SUBMITTALS .1 Submit product data in accordance with Section 01 33 00 – Submittal Procedures:

.1 Submit manufacturer's printed product literature.

.2 Submit shop drawings in accordance with Section 01 33 00 – Submittal Procedures:

.1 Indicate layout, dimensions, elevations, detail sections of members and sill conditions, materials, finishes, recesses, hardware including mounting heights, anchors and reinforcements, provisions for expansion and contraction, methods of joining sheet metal and joint locations, [glass types and] glass thicknesses, glazing details, types of sealants, details of other pertinent components of the work, and adjacent construction to which work of this section is attached.

.2 Identify installation tolerances required, assembly conditions, routing of service lines, locations of operating components, controls, and boxes.

.3 Indicate door signs.

http://www.sspc.org/

http://nace.org/nace/index.asp


.3 Submit templates and diagrams for distribution to fabricators and installers of related work as required for coordination with concrete work, electrical work, and other related work.

.4 Submit warranty.

.5 Submit proof of compliance with ANSI A156.10.

.6 Submit manufacturer’s proof of current membership in the AAADM.

.7 Manufacturer's Instructions:

.1 Submit manufacturer's printed installation instructions, technical data sheets, and standard details.

1.4 CLOSEOUT SUBMITTALS .1 Submit project record documents in accordance with Section 01 11 00 – General

Requirements: Closeout Submittals.

.1 Accurately record locations of concealed equipment, services, and conduit.

.2 Operation and Maintenance Data:

.1 Submit manufacturer's operation and maintenance data in accordance with Section 01 78 00 – Closeout Submittals.

.3 Parts List:

.1 Submit manufacturer's parts lists in accordance with Section 01 78 00 – Closeout Submittals; include servicing frequencies, instructions for adjustment and operation applicable to each type of component or hardware, and name, address and telephone number of nearest authorized service representative.

1.5 QUALITY ASSURANCE .1 Manufacturer’s Qualifications: Manufacturer to have at least 10-years’ experience in the

fabrication of automatic sliding door systems, and be a member in good standing of the American Association of Automatic Door Manufacturers (AAADM).

.2 Installer’s Qualifications: Products specified shall be installed by a factory-trained installer. Installer shall maintain a parts inventory, and have factory-trained service personnel with experience installing and maintaining units indicated for this project.

.3 Automatic equipment to comply with UL325 (Canada).

.4 Automatic equipment to comply with ANSI A156.10.

.5 Source Limitations: Obtain automatic entrance door assemblies through one source from a single manufacturer.

.6 Test Reports: certified test reports showing compliance with specified performance characteristics and physical properties.

.7 Certificates: product certificates signed by manufacturer certifying materials comply with specified performance characteristics and criteria and physical requirements.

1.6 DELIVERY, STORAGE, AND HANDLING .1 Deliver, store, handle and protect materials in accordance with Section 01 67 00 –

Material and Product Requirements.

.2 Cover exposed metal surfaces with pressure sensitive heavy protection paper or strippable plastic coating. Do not use materials of the type which will become bonded when exposed to the sun, or leave residue. Use padded blankets or approved protective wrapping for decorative metal work and similarly finished exposed elements.

.3 Store inside building in dry protected area away from construction activity.


.4 Protect finish surfaces from damage during handling, erection and at point of installation.

1.7 SITE CONDITIONS .1 Field Measurements: Verify openings to receive automatic entrance door assemblies by

field measurements before fabrication and indicate measurements on shop drawings.

.2 Established Dimensions: Establish dimensions and proceed with fabricating automatic entrances without site measurements where site measurements cannot be made without delaying the Work, coordinated with other construction to ensure that actual dimensions correspond to established dimensions.

1.8 MAINTENANCE .1 Extra Materials:

.1 Provide in accordance with Section 01 78 00 – Closeout Submittals.

.2 Provide wrenches and tools required for maintenance of equipment.

.2 Maintenance Service:

.1 Furnish complete service and maintenance of operating equipment for 1-year from date of Substantial Performance of the work.

1.9 WARRANTY .1 Warranty power operators, controls and labor provided by automatic sliding door

equipment installer against defects in material and workmanship, at no cost to owner, for a period of 2-years from date of Substantial Performance. Provide warranty to owner after completion of installation.

.2 Contractor agrees to correct any deficiencies in labour or material found in the work performed for a period of 2-years from the date of Substantial Performance.

Part 2 Products

2.1 SUSTAINABLE PRODUCT REQUIREMENTS .1 Products and construction processes shall comply with the requirements of

Section 01 47 15 - Sustainable Requirements to extent practicable, including using Products with high recycled content, Products with low embodied energy, Products regionally available, and Products that are low-emitting.

.1 Submit compliant Products for review and consideration to requirements of Section 01 62 00 - Product Options.

2.2 MANUFACTURERS .1 Single source requirements: all automatic sliding entrance door systems and sidelights

shall be supplied by a single manufacturer.

.2 Subject to compliance with requirements and Basis-of-Design criteria, manufacturers offering products that may be incorporated into the Work include the following:

.1 ASSA ABLOY Entrance Systems (Besam).

.2 Nabco Entrances Inc.

.3 Stanley Access Technologies.

.3 Door System Basis-of-Design:

.1 Entrances and at Cooler: Besam SL500 automatic sliding door, overhead concealed full breakout, narrow stile bi-parting sliding door.


.2 Besam SL500 automatic sliding door, overhead concealed full breakout, narrow stile single slide door system; where indicated.

2.3 PERFORMANCE REQUIREMENTS .1 General: Provide doors that have been designed and fabricated to comply with specified

performance requirements, as demonstrated by testing manufacturer's corresponding standard systems.

.2 Compliance:

.1 ANSI/BHMA A156.10 American National Standard for Power Operated Pedestrian Doors.

.2 UL 325 listed.

.3 Automatic door equipment accommodates medium to heavy pedestrian traffic.

.4 Automatic Door equipment accommodates up to the following weights for active leaf doors:

.1 Single doors: 300 lbs (136 kg) per active breakout leaf.

.5 Operating Temperature Range: -31 degrees F to 122 degrees F (-35 degrees C to 50 degrees C).

.6 Entrapment Force Requirements:

.1 Power Operated Sliding Doors: Not more than 30 lbf (133 N) required to prevent stopped door from closing.

.2 Sliding doors provided with a breakaway device shall require no more than 50 lbf (222N) applied 1 inch (25 mm) from the leading edge of the lock stile for the breakout panel to open.

2.4 EQUIPMENT .1 General: Equipment and Related Equipment shall be as supplied by manufacturer for

system installed; refer to Basis-of-Design products for minimum standards, quality and requirements.

.2 Manufactured Door Units: shall include operator, header with roller track, carrier assemblies, framing jambs, sliding door panels, sidelights, activation, safety devices and accessories required for complete installation.

.1 Configuration: Single slide, two equal panel door unit with one operable leaf and one sidelight unit.

.2 Traffic Pattern: two-way traffic.

.3 Emergency Breakaway Capability: Interior sliding leaf and sidelight unit.

.4 Mounting: Overhead header installed between jambs.

.5 Dimensions: Confirm door package dimensions with as-found site conditions, and match existing dimensions.

.3 Doors and Frames: Extruded Aluminum, Alloy 6063-T5.

.1 Door panels shall have a minimum .125 inch (3.2 mm) structural wall thickness including adjoining horizontal members and perimeter frames where applicable.

.2 Door Construction shall be by means of an integrated corner block with 3/8 inch all-thread through bolt from each stile.

.3 Glass stops shall be .062-inch (15.8 mm) wall thickness and shall provide security function as a standard by means of a fixed non-removable exterior section with glazing to be performed from the interior only. Glazing stops that allow for glass removal from the exterior shall not be deemed as equivalent.


.4 The sliding door system shall include two interlocks securing the leading stile of the sidelight and the butt stile of the sliding door panel together.

.5 Vertical Stiles shall match existing vertical stiles.

.6 Bottom Rails shall match existing bottom rails.

.7 Intermediate Muntin shall match existing intermediate muntin.

.8 Interior Vestibule Doors: .1 Weather-stripping shall be slide-in type, replaceable pile mohair seals

retained by the aluminum extrusions. The following types of weather-stripping are required: complementing weather-stripping on the joining vertical stiles of the sidelight and sliding door panels, complementing weather-stripping on the lead edge of the lock stiles of bi-parting doors, single pile weather-stripping between the carrier and the header, single pile weather-stripping on the lead edge stile of single slide door panels, dual pile weather-stripping on the pivot stile of breakout sidelight panels, and dual pile weather-stripping on the butt stile of fixed sidelight panels. Bottom rails shall be provided with an adjustable nylon sweep.

.9 Exterior Entrances and at Cooler doorway: .1 EcoDoor Seals: High pile mohair weather stripping on the lock stile of

the sliding doors, integrated mohair weather stripping with vinyl fin on the joining vertical stiles of the sidelight and sliding door panels, and expandable foam inserts in leading stile of sidelight panels at pockets for interlocks. Bottom rails shall be provided with a concealed adjustable nylon sweep.

.4 Glass: to Section 08 50 80 – Glazing.

.5 Door Carriers: Manufacturer’s standard carrier assembly that allows vertical adjustment.

.1 Carriage Assembly: Carriage bar with two-wheel assemblies. Each assembly shall have tandem roller wheels.

.2 Roller Wheels: Two heavy duty Delrin roller wheels per wheel assembly, for a total of four (4) roller wheels, 1-7/16-inch (36.51 mm) diameter, per active door leaf for operation over a replaceable aluminum track. Single journal with sealed oil impregnated bearings.

.3 Two (2) heavy duty self-aligning anti-risers per leaf.

.6 Framing Members: Provide automatic entrances as complete assemblies. Manufacturer’s standard extruded aluminum framing reinforced as required to support loads.

.1 Vertical jambs shall match existing in dimension.

.7 Header: Manufacturer's standard one-piece extruded aluminum header with a replaceable aluminum track extending full width of entrance unit. Header to conceal door operators, carrier assemblies, and roller track; complete with hinged access panel for service of door operator, and controls.

.1 Span: Maximum 16'-0" (4.9 m) without intermediate supports when using 1/4-inch glass.

.2 Capacity: Capable of supporting active breakout leaves up to maximum of 300 lb (136 kg) per leaf when header is supported per manufacturer's recommendations.

.3 Size: as required to suit conditions and to match existing as closely as possible. .1 Header height including the sensor plate cap which spans the clear door

opening width is 8-1/2 inches (215.9 mm) high. .4 Hinge Point: Continuous hinge at top of header allows for complete access to

operator and internal electronic and mechanical assemblies. .5 Design: Manufacturer's standard closed header.


.8 Hardware: Provide manufacturer's standard hardware as required for operation indicated.

.1 Breakaway arms and bottom pivot assemblies shall be supplied by the manufacturer and shall be adjustable to comply with applicable Codes.

.2 Exterior Entrance: .1 Wind resistant hydraulic damper to control movement of breakout

panels. .2 Bottom ball detent on breakout sidelight panels to provide additional wind

resistance. .3 Interior Vestibule Doors:

.1 Magnetic catch(s) to retain breakout door and sidelight panels in the closed position.

.9 Locking hardware shall be provided as indicated.

.1 Match existing exterior and interior hardware as closely as possible; manufacturer’s standard keyed cylinder; match existing keying, provide 4 extra keys each door.

.10 Guide Track/Threshold: Manufacturer’s threshold to match existing configurations and dimensions as closely as possible.

.1 Exterior Entrance: 1/2-inch (12.7 mm) high by 4-1/2 inch (114.3 mm) width continuous aluminum threshold with integral track shall span the entire width of the sliding door header and fit between the vertical framing members. Threshold design shall allow for optional extruded ramps to securely interlock to flat section to meet ADA requirements. .1 Recessed mounted.

.2 Interior Doors: Aluminum guide track integrated in the bottom of the sidelight portion of the sliding automatic door assembly.

2.5 SLIDING DOOR OPERATOR .1 Door Operator and Controller:

.1 Electro-mechanical controlled unit utilizing a high-efficiency, energy efficient, DC motor requiring a maximum of 3-amp current draw, allowing 5 operators on one 20 amp circuit. The supplied system shall have the capability to operate at full performance well beyond a brown out and high line voltage conditions (85V - 265V) sensing changes and adjusting automatically. The operator shall allow an adjustable hold open time delay of 0 to 60 seconds and have internal software to incorporate a self-diagnostic system.

.2 Microprocessor Control Box:

.1 Modular control unit to allow for changing technology. Factory-adjusted configuration with opening and closing speeds set to comply with ANSI/BHMA A156.10 requirements and electronic dampening to reduce wear on drive train. Should the drive train operations deviate from design criteria ranges, Watchdog Control Circuit Monitoring will assume command of the system and shut down the automatic function allowing a secondary supervisory circuit to perform as a backup. Control unit shall allow the following functions: .1 Diagnostics with the ability to produce application data.

.3 Mode Selector Control:

.1 Multi-position keyed cylinder mode selector switch to be interior jamb mounted and shall allow selection of the indicated functions to be engaged when switch is turned to the appropriate setting.

.2 Mode selector control to allow the following functions:


.1 "Off"

.2 "Exit Only" one-way traffic with automatic operation from the interior.

.3 "Two Way Traffic" allowing automatic operation from exterior and interior.

.4 "Partial Opening" energy saving door position allows door to automatically adjust opening width based on amount of usage, that is, full open during high use and partial open during low use. The control for this setting is programmable allowing adjustment to both the usage setting and the opening width.

.5 "Hold Open" doors activated and held in the full open position.

2.6 ACTIVATION AND SAFETY CONTROL DEVICES .1 General: Provide the types of activation and safety devices specified in accordance with

ANSI/BHMA standards, for the condition of exposure and for long-term, maintenance-free operation under normal traffic load for type of occupancy indicated. Coordinate activation and safety devices with door operation and door operator mechanisms.

.2 Combination Activation Motion Sensor/Safety Presence Sensor:

.1 Shall be a sliding door sensor utilizing K-band microwave technology to detect motion and focused active infrared technology to detect presence, combined in a single housing surface mounted on each side of the header. .1 Presence sensor shall remain active at all times. .2 The sensor shall communicate with the automatic door operator through

a self-monitoring connection that allows the door to go into a fail safe mode preventing the door from closing in the event of a sensor failure.

.2 Motion/presence detecting sensors to be field installed and adjusted.

2.7 ELECTRICAL .1 High-Efficiency DC Motor: Maximum of 3-amp current draw, allowing 5 operators to run

on one 20 Amp circuit.

.2 Power: Self-detecting line voltage capable control. 120 VAC through 240 VAC, 50/60 Hz, 3 amp minimum incoming power with solid earth ground connection for each door system.

.3 Key Impulse Input: Input for card readers or remote activation with independent adjustable hold open delay.

.4 Wiring: Separate internal channel raceway free from moving parts.

.5 Brown out / high voltage capability: System has capability to operate at full performance well beyond brown out and high voltage line conditions (85 V - 265 V) sensing changes and adjusting automatically.

.6 Convenience Battery: Shall be concealed in header and capable of full operation with blackout conditions, including sensor capabilities for minimum of 100 cycles.

2.8 ALUMINUM FINISHES .1 Anodized aluminum: AAMA 611, Clear, AA- M12C22A41, Class I, 0.018 mm.

Part 3 Execution

3.1 MANUFACTURER'S INSTRUCTIONS .1 Compliance: comply with manufacturer's printed installation instructions, data sheets,

specifications and standard details.

NSLC Berwick Store Renovation Section 08 42 29 NSL-057 Berwick - December 2020 SLIDING AUTOMATIC ENTRANCES Page 9 of 10 3.2 INSPECTION

.1 Verify surfaces, openings, and recesses are ready to receive work, and opening dimensions are as indicated on shop drawings.

.2 Verify power supply is available and roughed in to power operated devices.

.3 Beginning of installation means acceptance of conditions.

3.3 PREPARATION .1 Obtain all dimensions from the job site.

.2 Provide data, dimensions and components, anchors and assemblies to be installed by others in proper time for installation.

.3 General or electrical contractor shall install all wiring to operator on a separate circuit breaker routed into header. General or electrical contractor shall also install all necessary power, connection to power, and low voltage wiring for proper operation of associated security systems.

3.4 INSTALLATION .1 Install doors and frames in accordance with shop drawings and manufacturer's

instructions.

.2 Coordinate installation of components with related and adjacent work; attach and seal air and vapour barrier materials to perimeter framing.

.3 Set work plumb, square, level, free from warp, twist, and superimposed loads.

.4 Securely anchor work in required position; do not restrict thermal movement.

.5 Brace frames rigidly for building in; provide temporary horizontal spreaders at third points of door openings to maintain frame width; vertically support at centre, heads of openings over 1220 mm (48") wide; remove temporary bracing after framing is set.

.6 Apply isolation coating to separate aluminum and primed or galvanized steel surfaces at points of contact with cementitious materials.

.7 Install foam-in-place insulation in shim spaces at perimeter of assembly and void spaces between members to maintain continuity of thermal barrier.

.8 Maintain clearances between head members and structure to ensure that structural loads are not transmitted to frames.

.9 Install hardware using templates provided by Owner.

.10 Install door operator system in accordance with manufacturer's instructions, including controls, and control wiring.

.11 Set tracks, header assemblies, operating brackets, rails, and guides level and true to location, with adequate anchorage for permanent support.

.12 Factory-install glass in accordance with Section 08 80 50.

3.5 SEALANT APPLICATION .1 Install perimeter sealant and back up materials, to provide weather tight seal at outside

and air, vapour seal at inside.

.2 Comply with requirements of Section 07 92 00 – Sealants for sealants, fillers, and gaskets to be installed during installation of doors and frames.

.3 Conceal sealant within aluminum work except where exposed use is permitted by Consultant.

.4 Set sill members in bed of sealant.

NSLC Berwick Store Renovation Section 08 42 29 NSL-057 Berwick - December 2020 SLIDING AUTOMATIC ENTRANCES Page 10 of 10 3.6 ADJUSTING

.1 After repeated operation of completed installation equivalent to three days of use by normal traffic (100 to 300 cycles), readjust door operators and controls for optimum, smooth operating condition and safety and for weather tight closure.

.2 Lubricate hardware, operating equipment and other moving parts.

.3 Adjust revolving doors to provide tight fit at contact points with enclosure.

3.7 CLEANING .1 Clean glass and aluminum surfaces promptly after installation; exercise care to avoid

damage to coatings.

.2 Remove protective material from prefinished aluminum surfaces.

.3 Wash exposed surfaces with mild solution of detergent and warm water, using soft, clean wiping cloths. Remove dirt from corners. Wipe surfaces clean.

.4 Remove excess sealant by moderate use of solvent, of type acceptable to sealant manufacturer.

.5 Ongoing progress and final cleaning shall be performed under work of Section 01 74 11 - Cleaning.

.6 Manage and dispose of demolition and construction waste materials in accordance with Section 01 74 19 - Waste Management and Disposal.

3.8 PROTECTION .1 Protect installed products and components from damage during construction.

.2 Repair damage to adjacent materials caused by Work of this Section.

3.9 DEMONSTRATION .1 Demonstrate operation, operating components, adjustment features, and lubrication

requirements to Owner as required.

3.10 SCHEDULE .1 Locate at walk-in cooler between cooler and remainder of store.

END OF SECTION

NSLC Select Store Roll-Out Section 27 05 13 NSL-057 Berwick – December 7, 2020 STRUCTURED CABLING FOR COMMUNICATIONS SYSTEMS Addendum No.1 Page 1 of 7

GENERAL

1.1 GENERAL REQUIREMENTS

.1 Supply and install a complete telecommunications cabling system based on a physical star wiring topology that is designed in accordance with and supported by a twenty-five (25) year manufacturer-backed warranty and certification as specified herein.

.2 The structured cabling system must be standards compliant and shall comprise of all components specified, implied, or otherwise necessary to constitute a fully operational system. The work includes, but is not necessarily limited to, the following: .1 Cross-connect System. .2 Horizontal cabling system. .3 Telecommunications outlet/connector associated cords and adapters. .4 Patch panels.

1.2 DESCRIPTION OF WORK

.1 Data cabling system as indicated herein and which generally includes but is not limited to: cabling terminations, cross connects, horizontal cabling, BIX panels, cable management, etc. Active components (hubs and switches) are not part of this work, except where indicated otherwise.


.1 Section 26 05 00 – Electrical General Requirements.

.2 Section 26 05 01 – Electrical Identification.

1.4 REFERENCES

.1 CAN/CSA C22.1-18(R2020), Canadian Electrical Code.

.2 CAN/CSA C22.2 No. 226-92(R2016), Protectors in Telecommunications Networks.

.3 TIA-568.0-2020, Generic Telecommunications Cabling for Customer Premises

.4 TIA-568.1-2020, Commercial Building Telecommunications Infrastructure Standard.

.5 TIA-568.2-2018, Balanced Twisted Pair Cabling and Components Standard.

.6 TIA-568.3-2016, Optical Fibre Cabling Components Standard.

.7 TIA-568.4-2017, Broadband Coaxial Cabling and Components Standard.

.8 TIA-569-2019, Telecommunications Pathways and Spaces.

.9 TIA-598-2014, Optical Fibre Cable Color Coding.


.10 TIA-606-2017, Administration Standard for Telecommunications Infrastructure.

.11 ATIS J-STD-607-2002, Commercial Building Grounding (Earthing) and Bonding Requirements for Telecommunications.

.12 TIA-758-2012, Customer Owned Outside Plant Telecommunications Infrastructure Standard.

.13 BICSI Telecommunications Distribution Methods Manual (TDMM), latest edition.

.14 BICSI Information Transport Systems Installation Methods Manual (ITSIMM), latest edition.

1.5 QUALIFICATION OF SYSTEM

.1 The cabling system, materials and installation practices must strictly conform to the current issue of industry standards TIA 568, TIA 568-C.2-1, CSA C22.1 Canadian Electrical Code Part 1. All performance requirements of this document must be followed. In addition, workmanship and installation methods used must be equal to or better than those found in the BICSI (Building Industry Consulting Service International) TDM Manual (latest edition).

.2 The cabling system must conform to applicable local building and electrical safety codes. Have the vendor apply and receive acceptance for the installation by the electrical inspector as per the Canadian Electrical Code.

.3 Qualified vendors must provide technical field services in compliance with labour standards (Communications Cabling Specialist, CCS). Obtain an installation permit from the Electrical Inspection Department for the Work on this Project.

.4 Source all structured cabling, termination hardware, and connecting cords from the certifying manufacturer to assure quality control and validity of the manufacturer’s warranty.

.5 Accept complete responsibility for the installation, certification, and support of the cabling system. Provide proof that vendor has the certifying manufacturer’s support on all of these issues.

.6 Qualified vendors must maintain Belden IBDN Certified System Vendor (CSV) accreditation throughout the duration of the project. Provide proof of certification with shop drawing and maintenance manual submission.

1.6 PRODUCT DATA

.1 Submit product data indicating system components, mounting method, grounding, and special attachments including tie-ins to all external facilities.

1.7 SUBMITTALS

.1 Submit: .1 A complete telecommunications cabling system layout, including cable routing,

telecommunications closet(s) and telecommunications outlet/connector


designations. Layout to detail locations of all equipment and indicate all wiring pathways.

.2 Manufacturer's technical documentation on all devices used in cabling system.

.3 Results of all tests for review. Conduct and pay for all required testing as indicated herein.

1.8 IDENTIFICATION

.1 Provide identification for communications systems in accordance with Section 26 05 00 – Electrical General Requirements.

PRODUCTS

2.1 TERMINATION SUB-SYSTEMS

.1 Telecommunications equipment racks: .1 Existing rack to be reused.

.2 Patch Panels: .1 Patch panels to be TIA-568C Category 6 complete with RJ45 jacks and designed

for mounting in 19" racks. Provide all required mounting brackets and hardware. .2 All patch panels must be fully populated with jacks, regardless of quantity

terminated. .3 Patch panels to be 48-port, 2U, black, flex patch panels, Belden #AX101458. .4 Patch panel modular jacks (MVDO) as follows:

.1 Data distribution (POS)-white.

.2 Data distribution (Non-POS)-Grey.

.3 Voice distribution – Blue.

.4 Security distribution – Yellow.

.5 Fibre optic patch panels to be provided by Owner.

.3 Work area telecommunications outlet/connector: .1 The work area telecommunications outlet/connector is the interface between the

horizontal wiring and the work area device (via line cord). .2 Install all telecommunications outlet/connectors in an appropriate faceplate. .3 Faceplates must be clean in appearance and complete with identification inserts

and clear covers. Mounting hardware shall not be visible on the faceplate. .4 Flush mounted faceplates to accommodate modular telecommunications

outlet/connectors and other multimedia outlets as indicated provide with required number of connectors. Faceplates to be as follows: .1 Two-port: Belden #AX101433.

.1 Four-port: Belden #AX101437. .5 The eight-position modular UTP telecommunications outlet/connector and its pin

assignments must meet the requirements described in the TIA-568C standard as T568A, and must be CAT 6 compliant.

.6 All work area telecommunications outlets to have their modular outlets colour coded as follows: .1 Voice distribution: Blue, Belden #AX101071. .2 Data distribution (POS): White, Belden #AX101065. .3 Data distribution (non-POS): Grey, Belden #AX101063.

.7 Supply and install blank module covers in all unused openings in faceplates. Colour to match faceplate.


.8 Uniquely label each telecommunications outlet. The label will form an integral part of the faceplate.

.9 Serve each telecommunications outlet from a telecommunications room located on the same floor as the telecommunications outlet.

.10 Provide dust covers for all work-area telecommunications modular outlets.

2.2 HORIZONTAL CABLING

.1 Horizontal cables to consist of eight (8) #23 AWG insulated, solid conductors, formed into four individually twisted pairs. Refer to drawings for location and quantity of horizontal data cables.

.2 Limit the horizontal cable length from the telecommunications rack to the farthest workstation area to 295 feet, as specified in the TIA-568-C standard document.

.3 The installation of the horizontal cable must follow the appropriate recommendations covered in the respective manufacturer's design guide and the appropriate standards documents. This is done in order to provide adequate protection from electromagnetic interference (EMI) sources and to confirm all components and cables are in good condition after installation.

.4 All UTP data cabling must be CAT 6 cable and meet or exceed the transmission and electrical characteristics of the TIA 568-C.2-1 requirements for horizontal cabling for Extended Frequency LANs. The UTP cable to be minimum CMP (FT-6) rated cable. The UTP cable consists of #23 AWG thermoplastic insulated solid conductors formed into four individually twisted pairs and enclosed in a thermoplastic jacket.

.5 Provide technology J-hooks, conduit, pull boxes as indicated or as required by code.

.6 Provide technology all faceplates and appurtenances necessary for the installation of telecommunications outlets in wall boxes. Install conduit and boxes in walls where indicated.

.7 All data and coax cabling must be home runs (1 cable per drop) from the telecommunications closet to the work area.

.8 Colour code horizontal cabling as follows: .1 Data cabling for all POS components must shave white colour jacket. Data

cabling for all non-POS components to have grey outer jacket. .2 Voice cabling shall have blue outer jacket. .3 Security cabling shall have yellow outer jacket.

.9 Acceptable Material: Belden Gigaflex 2400 series.

2.3 MODULAR LINE AND PATCH CORDS

.1 General: .1 Modular line/patch cords consist of #24 AWG insulated, solid or stranded

conductors formed into four (4) individually twisted pairs and enclosed in a jacket. No cord may degrade the required channel performance characteristics as per TIA-568-C. Cover all cords by the manufacturer's warranty and certification. All cords must maintain the appropriate polarity.


.2 Total line and patch cord lengths per channel must not exceed 30 ft.

.3 Work area (line cords): .1 Use modular line cords to attach each workstation network interface card to a

telecommunications outlet/connector. They must not normally exceed 10 ft in length as per TIA-568-C. Provide line cords with eight-position modular plugs terminated at both ends. The modular plugs must comply with TIA-568-C. Pin configuration to be T568A (as per TIA-568-C).

.2 Use manufacturer factory-built and tested connectorized cords.

.3 Provide 10 ft long line cords.

.4 Provide sufficient quantity of line cords for total number of horizontal data cables installed.

.4 Telecommunications closets (patch cords): .1 Use modular patch cords to patch within each cross-connect. They must not

exceed 20 ft in length as per TIA-568-C. Provide patch cords with eight-position modular plugs terminated at both ends.

.2 Provide a patch cord for each installed CCTV data port plus 25% spare; patch cord lengths are to be minimized, spare patch cords are to be a variety of lengths to a maximum of 16 ft. Coordinate colour of spare patch cords with Owner prior to ordering.

.3 Use manufacturer factory-built and tested connectorized cords.

.5 Specifications: .1 All copper line and patch cords must be manufacturer backed, built and tested

with Category 6 characteristics which comply with TIA-568-C.

2.4 ACCEPTABLE PRODUCTS

.1 Belden IBDN.

EXECUTION

3.1 INSTALLATION

.1 Label all telecommunications outlet/connectors, patch panels, cross connects, cabinets, and other components in accordance with Section 26 05 00 – Electrical General Requirements. Regardless of the numbering scheme, every cable must have the same permanent identifier on its termination hardware at both ends. Have the numbering scheme approved by Consultant.

.2 Properly bond each equipment/distribution rack in the telecommunications room to a ground bus in accordance with the applicable code requirements as per ANSI-607 and Section 26 05 00 – Electrical General Requirements.

.3 Perform installation in a professional manner using the best practices in the industry. Best practices shall include, but not be limited to, the following points: .1 All cabling must be continuous without joints, or splices from the work area to the

telecommunications room. .2 Install all voice and data cables in conduits in walls and in areas with exposed

ceilings. Provide technology J-hooks (1-24 cables only) above accessible ceilings. Ensure cables above ceilings are within 30” of ceiling. Provide cable trays where noted on the drawings. The maximum number of bends between


cable pulling points will be two (2) ninety degree bends over a maximum of 100 ft.

.3 Install all cables for cameras entirely in conduit in exposed areas. Utilize j-hook supports above suspended ceilings.

.4 Horizontal fill ratios for conduit, cable trays, raceways, and ducts must conform to standards and manufacturer recommendations including 25% spare for future installation.

.5 Follow standards for separation distances between cables and sources of electromagnetic interference.

.6 Handle, install, and support all cables in accordance with the manufacturer's guidelines. During the laying of the cable, take care not to overstress the cable. After the cable is installed, make sure that all parts of the cable are supported properly and stress free at both ends and throughout their length.

.7 Give appropriate attention to the handling of all cables to confirm bending radius conforms to the manufacturer's requirements. At no time shall the cable's static or dynamic bending radius be exceeded.

.8 Securely mount all telecommunications outlet/connectors at all work area locations and locate so that the cable required to reach the work area equipment will be no longer than three meters.

.9 Coordinate work with that of other trades.

.10 Terminate all four (4) pairs of unshielded twisted pair (UTP) cable on a single port. The splitting of cable pairs between different jacks is not permitted.

.11 Provide a minimum 10 ft service loop at the telecommunications room by routing the cables to the rack by the longest route in the cable tray within the TR.

.12 Provide 5 ft cable slack loops above the telecommunications outlet in the accessible ceiling space. The loops must have a minimum bend radius of 7 in.

.13 Install all optical fibre backbone cabling inside 1-1/8” diameter inner-duct. Inner-duct shall be minimum FT-4 rated complete with pull tape.

.14 Terminate voice backbone cables with two (2) pairs per port.

.4 Install outside plant (OSP) cables in accordance with ANSI/TIA-568-C. Outside plant (OSP) cables within the premise must be run in conduit, except that a maximum of 10 ft may be exposed at the termination point.

.5 Provide enough cable for LAN rack relocation of up to 10 ft in all directions.

3.2 TESTING AND CERTIFICATION

.1 Provide commissioning, verification, inspection, and certification. Conduct and pay for all tests required.

.2 Conduct end-to-end testing for UTP copper for 100% of pairs as follows: .1 Balanced twisted-pair cable testing:

.1 Use testing procedures applicable to the horizontal cabling configuration to meet field test compliance. Consolidation/Transition points are optional interface points as specified and permitted under ANSI/TIA/EIA specifications and are considered a seamless link for acceptance testing.

.2 The field testing acceptance parameters for balanced twisted-pair cabling are as follows: .1 Wire map (continuity). .2 Length. .3 Insertion loss. .4 NEXT Loss. .5 ELFEXT. .6 Propagation delay and delay skew.


.7 Return loss.

.8 Power sum near-end crosstalk (PSNEXT) loss.

.9 Power sum equal level far-end crosstalk (PSELFEXT). .3 Level III field test instruments are required for measurements up to

Category 6 and Class E cabling. .4 Document and provide to the Consultant acceptance testing results.

.3 Conduct field testing for cables as follows: .1 Where applicable, conduct the following tests:

.1 DC loop resistance.

.2 Impedance.

.3 Length.

.4 TDR.

.5 Attenuation.

.6 Noise. .2 The required tests and acceptance may depend on the application and the

system design requirements. .3 Document and provide to the Consultant acceptance testing results as

compliance with Part 3.3 - Project Documentation, below.

.4 Verify labelling of all wiring at all termination points in accordance with Section 26 05 00 – Electrical General Requirements.

.5 The Consultant reserves the right to check and verify all installation performed by the Contractor. In case of failure to meet certification standards, reinstall any non-compliant cabling at no additional cost to the Contract.

3.3 PROJECT DOCUMENTATION

.1 Test Results: .1 Provide test results on CD-ROM or USB memory stick in Fluke Linkware format

(.FLW files). .2 Provide test results in hard-copy format and include with the Operation and

Maintenance Manual submission.

.2 Manufacturers’ Warranty: .1 Provide a manufacturer generated and supported Product Warranty and

Application Assurance certificates upon completion of installation and acceptance by the Consultant.

.2 Product Warranty and Application Assurance must provide coverage of materials and labour for a minimum of twenty (20) years from date of Substantial Completion, regardless of installing agent/vendor status.

END OF SECTION

NSLC Select Store Roll-Out Section 27 05 28 NSL056 Berwick – December 7, 2020 TELECOMMUNICATIONS RACEWAY SYSTEM Addendum No. 1 Page 1 of 2

PART 1 - GENERAL

1.1 SYSTEM DESCRIPTION

.1 Telecommunications raceways system consists of outlet boxes, cover plates, terminal distribution cabinets, conduits, pull boxes, sleeves and caps, fish wires, technology "J" hooks.

.2 Overhead distribution system.


.1 Section 26 05 31 - Splitters, Junction, Pull Boxes and Cabinets.

.2 Section 26 05 34 - Conduits, Conduit Fastenings and Fittings.

PART 2 - PRODUCTS

2.1 MATERIAL

.1 Conduits: to Section 26 05 34 - Conduits, Conduit Fastenings and Fittings.

.2 Outlet boxes: to Section 26 05 31 - Splitters, Junction, Pull Boxes and Cabinets.

.3 Fish wire: polypropylene type.

PART 3 - EXECUTION

3.1 INSTALLATION

.1 Install raceway system, including fish wire, outlet boxes, pull boxes, cover plates, conduit, sleeves and caps, miscellaneous and positioning material to constitute complete system and in accordance with Section 26 05 34 - Conduits, Conduit Fastenings and Conduit Fittings.

.2 Use technology "J" hooks above accessible ceiling systems. Technology “J” hooks to be designed for use with CAT6 cabling.

.3 Use EMT in areas with unfinished or inaccessible ceiling systems and in all walls. Size in accordance with cable manufacturers recommendations. Under no circumstance, install more than 40% fill ratio in any conduit. Allow for 25% spare cables. Install bond conductor in all EMT.

.4 Provide nylon insulated bushings at conversion of EMT to free air system.

.5 Locate EMT type conduit "wall-stub" complete with flush installed device box in walls/partitions. Turn stubs out into accessible ceiling space within the same room where possible.

NSLC Select Store Roll-Out Section 27 05 28 NSL056 Berwick – December 7, 2020 TELECOMMUNICATIONS RACEWAY SYSTEM Addendum No. 1 Page 2 of 2

.6 Where the "grouping" of various systems outlets or multiple type outlets in dry-wall type construction is specified, the use of "box mounting brackets" are to be installed between, and secured to both metal studs. Install suitably sized 4” square and/or 5” boxes complete with raised tile rings as required.

.7 Minimum conduit size to be 1” diameter.

.8 Provide telecommunications 4” (square) outlet boxes and provide complete with single gang square raised tile ring.

.9 Provide sleeves for telecommunications, CCTV, and security cabling though walls which do not form a rated fire separation. Refer to Section 26 05 34 - Conduits, Conduit Fittings and Conduit Fastenings for more information.

END OF SECTION

SEE DOORSCHEDULE

2"

2"

SEE

DOOR

SCH

EDUL

E

SEE DOORSCHEDULE

SEE

DOOR

SCH

EDUL

E

SEE DOORSCHEDULE

SEE

DOOR

SCH

EDUL

E

SEE DOORSCHEDULE

SEE

DOOR

SCH

EDUL

E

MECH.ROOM

106W/R107

W/R108

JANITORROOM

109

WAREHOUSE105

BEER COOLER104

RETAIL SPACE102

OFFICE103

STAFF ROOM110

101

C

ELEC RM104

CANNABIS110

VESTIBULE

BEER COOLER104

RETAIL SPACE102

OFFICE103

STAFF ROOM110

101

ELEC RM104

CANNABIS110

VESTIBULE

SCHEDULES,& PHASING

BREAKHOUSE

A-002-R1

NSL-057

3/16" = 1'-0"SCALE:

PROJECT #:

DRAWN BY:

DRAWING #:

SEAL:

CLIENT:

PROJECT:

TITLE:


NORTH ARROW:

ISSUED/REVISIONS:

200 COMMERCIAL ST,BERWICK, NS B0P 1E0

NSLC BERWICKSTORE RENOVATION

Procurement Contact:TRACEY DARRIGANT. 902-450-5835E. [email protected]

NOVA SCOTIA LIQUORCORPORATION93 CHAIN LAKE DRIVEHALIFAX, NS, B3S 1A3

CBCL Limited1489 Hollis St, PO Box 606,

Halifax, NS, B3J 2R7

T 902-421-7241

F 902-423-3938

www.cbcl.ca

PHASING PLAN - PHASE 1D1A-002

1/8" = 1' - 0" PHASING PLAN - PHASE 2D1A-002

1/8" = 1' - 0"

ABCEFG

1

2

3

29'-0" 24'-0" 24'-0" 24'-0" 24'-0"

125'-0"

35'-4

"24

'-8"

60'-0

"

MECH.ROOM

106W/R107

W/R108

JANITORROOM

109

WAREHOUSE105

BEER COOLER104

RETAIL SPACE102

OFFICE103

STAFF ROOM110

101

ELEC RM104

CANNABIS110

B1

A701

A501

D1

A1

A-202 C1C2

A-202

D3

D1

A4A-202

A-202

B3

B4

D1A104

P1

D-08GL2

GL2

GL2

GL1

D-02D-05

D-06D-01

D-07

P2

P2

C1A-501

A3A-501

D1A-501

D-03

GL3

D-09

D-04

D-04

D-04

D-04

D-04

D-04

D-04

D-04

D-04

D-04

D-04

D-04

D-04

D-04

P3

C1A-501

P4

P3

VESTIBULE

P4

P2

P1 P3

P4

FLOOR PLAN

BREAKHOUSE

A-102-R1

NSL-057

3/16" = 1'-0"

FLOOR PLAN D1A-102

3/16" = 1' - 0"

SCALE:

PROJECT #:

DRAWN BY:

DRAWING #:

SEAL:

CLIENT:

PROJECT:

TITLE:


NORTH ARROW:

ISSUED/REVISIONS:







T 902-421-7241

F 902-423-3938

www.cbcl.ca

x

– – – ––

x

Employees OnlyEmergency Exit

”

“ ”

” ” ” ”

”

“ ”

FINISH FLOORELEV. 0'-0"

BEER COOLER104

RETAIL SPACE102

OFFICE103

STAFF ROOM110

101

ELEC RM104

CANNABIS110

SN03

SN06

SN06

SN06

SN06

SN06

SN06

SN06

SN06

SN06

SN06

SN06

SN06

SN06

SN06

SN06

SN06

SN06

SN06

SN06

SN06

SN06

SN06

SN06

SN06

SN06

SN06

SN06

SN06

SN06

SN06

SN06

SN06

SN06

SN06

SN06

SN06

SN06

SN06

SN06

SN06

SN06

SN06

SN06

SN06

SN06

SN06

SN06

SN06

SN01

SN05A

SN05B

SN05B

SN04

SN04SN07BSN07C

SN07BSN07C

SN07BSN07C

SN04SN07C

SN09

SN07B

VESTIBULE

SN10 SN10 SN10 SN10SN02

SN10SN10SN10

SN10

SN09

AS NOTEDSIGNAGE PLAN AND SCHEDULE

BREAKHOUSE

A-900-R1

NSL-057

AS NOTED

SIGNAGE PLAN

A2A-900

3/16"=1'-0"

SIGN DETAIL - SN01 & SN02

D4A-900

1/2"=1'-0" SECTION - SN01 & SN02

DETAIL - SN01 & SN02DETAIL - SN01 & SN021 1/2"=1'-0"

DETAIL - SN06 BASE3"=1'-0" DETAIL - SN081/2"=1'-0"

A-900

D3A-900

D2

A-900C2 NTS

A-900C3

1/2"=1'-0"

A-900

D5SCALE:

PROJECT #:

DRAWN BY:

DRAWING #:

SEAL:

CLIENT:

PROJECT:

TITLE:


NORTH ARROW:

ISSUED/REVISIONS:







T 902-421-7241

F 902-423-3938

www.cbcl.ca

SCALE:

PROJECT #:

DRAWN BY:

DRAWING #:

SEAL:

CLIENT:

PROJECT:

TITLE:


NORTH ARROW:

ISSUED/REVISIONS:

Contact:



T 902-421-7241

F 902-423-3938

www.cbcl.ca


STEPHEN BAYERT. 902-450-5916F. 902-450-6116



NEW CONSTRUCTION- POWER ANDTELECOM

CBCL

200613.06

AS NOTED

E-103-R1

NEW CONSTRUCTION - POWER & TELECOM

1-

3/16"=1'-0"

NEW CONSTRUCTION - ELECTRICAL ROOM

2-

1/2"=1'-0"

AutoCAD SHX Text

BP1-37

AutoCAD SHX Text

CD

AutoCAD SHX Text

BP1-48,50

AutoCAD SHX Text

CTP

AutoCAD SHX Text

MW

AutoCAD SHX Text

GFI

AutoCAD SHX Text

BP1-34

AutoCAD SHX Text

F

AutoCAD SHX Text

BP1-36

AutoCAD SHX Text

S-8

AutoCAD SHX Text

S-6

AutoCAD SHX Text

BP1-43

AutoCAD SHX Text

S-7

AutoCAD SHX Text

S-5

AutoCAD SHX Text

1/2

AutoCAD SHX Text

2

AutoCAD SHX Text

BP1-43

AutoCAD SHX Text

BP1-47

AutoCAD SHX Text

FF

AutoCAD SHX Text

BP1-42

AutoCAD SHX Text

FF-1

AutoCAD SHX Text

BP1-41

AutoCAD SHX Text

S-4

AutoCAD SHX Text

S-2

AutoCAD SHX Text

S-1

AutoCAD SHX Text

S-3

AutoCAD SHX Text

1/2

AutoCAD SHX Text

2

AutoCAD SHX Text

ILS

AutoCAD SHX Text

BP2-24

AutoCAD SHX Text

BP1-37

AutoCAD SHX Text

CD

AutoCAD SHX Text

BP1-37

AutoCAD SHX Text

CD

AutoCAD SHX Text

BP1-37

AutoCAD SHX Text

CD

AutoCAD SHX Text

BP1-37

AutoCAD SHX Text

CD

AutoCAD SHX Text

BP1-37

AutoCAD SHX Text

CD

AutoCAD SHX Text

BP1-37

AutoCAD SHX Text

CD

AutoCAD SHX Text

BPB-1

AutoCAD SHX Text

BP1-38

AutoCAD SHX Text

CL

AutoCAD SHX Text

BP1-39

AutoCAD SHX Text

AHU-1

AutoCAD SHX Text

DP1-8,10,12

AutoCAD SHX Text

CARTS

AutoCAD SHX Text

BP1-44,46

AutoCAD SHX Text

CTP

AutoCAD SHX Text

AD

AutoCAD SHX Text

NEMA 4X

AutoCAD SHX Text

NEMA 4X

AutoCAD SHX Text

RHC-1

AutoCAD SHX Text

BP1-25,27

AutoCAD SHX Text

CL

AutoCAD SHX Text

S

AutoCAD SHX Text

MSS

AutoCAD SHX Text

CL

AutoCAD SHX Text

BP1-29

AutoCAD SHX Text

HYDRONIC

AutoCAD SHX Text

HEATER

AutoCAD SHX Text

CL

AutoCAD SHX Text

BP1-43

AutoCAD SHX Text

FF

AutoCAD SHX Text

BP1-42

AutoCAD SHX Text

FF-1

AutoCAD SHX Text

BP1-53

AutoCAD SHX Text

GFI

AutoCAD SHX Text


AutoCAD SHX Text

%%ULAYOUT:

AutoCAD SHX Text

K:\Projects\200613.06 NSLC BERWICK BWS\20 CAD\05 ELEC\200613.06 - E-103.dwg

AutoCAD SHX Text

%%UDATE:

AutoCAD SHX Text

December 9, 2020 4:40:22 PM

AutoCAD SHX Text

E-103

AutoCAD SHX Text

No.

AutoCAD SHX Text

Remarks

AutoCAD SHX Text

Date

AutoCAD SHX Text


AutoCAD SHX Text

GENERAL NOTES:

AutoCAD SHX Text

CONSULTANTS:

AutoCAD SHX Text

A

AutoCAD SHX Text

B

AutoCAD SHX Text

C

AutoCAD SHX Text

D

AutoCAD SHX Text

4

AutoCAD SHX Text

2

AutoCAD SHX Text

1

AutoCAD SHX Text

3

AutoCAD SHX Text


AutoCAD SHX Text

01

AutoCAD SHX Text

2020.10.16

AutoCAD SHX Text

ISSUED FOR REVIEW

AutoCAD SHX Text

02

AutoCAD SHX Text

2020.11.27

AutoCAD SHX Text

03

AutoCAD SHX Text

2020.12.15

AutoCAD SHX Text

ISSUED FOR TENDER

AutoCAD SHX Text

ADDENDUM NO.1

AutoCAD SHX Text

NOTES: 1. TRANSFER ALL EXISTING CIRCUITS FED FROM REMOVED 400A SPLITTER TO NEW PANEL 'DP1'. VERIFY ALL EXISTING LOADS TO REMAIN PRIOR TO COMMENCEMENT OF WORK. BRANCH WIRING TO BE REUSED WHERE POSSIBLE, PROVIDE NEW WHERE NOT. TRANSFER ALL EXISTING CIRCUITS FED FROM REMOVED 400A SPLITTER TO NEW PANEL 'DP1'. VERIFY ALL EXISTING LOADS TO REMAIN PRIOR TO COMMENCEMENT OF WORK. BRANCH WIRING TO BE REUSED WHERE POSSIBLE, PROVIDE NEW WHERE NOT. EXTEND/TRIM EXISTING CONDUCTORS AS REQUIRED TO TERMINATE AT NEW PANEL 'DP1'. REFER TO PANEL SCHEDULE ON DRAWING E-108 FOR ADDITIONAL LOADS. TRANSFER OF LOADS TO OCCUR AFTER STORE HOURS OF OPERATION. COORDINATE OUTAGES WITH THE OWNER'S SITE REPRESENTATIVE PRIOR TO COMMENCEMENT OF WORK. NSLC FACILITY IS TO REMAIN OPERATIONAL DURING CONSTRUCTION. REFER TO SPECIFICATION FOR PHASING DETAILS. 2. TRANSFER ALL EXISTING CIRCUITS FROM REMOVED PANEL 'A' TO NEW PANEL 'BP1'. VERIFY ALL EXISTING LOADS TO REMAIN PRIOR TO COMMENCEMENT OF WORK. BRANCH WIRING TO BE REUSED WHERE POSSIBLE, PROVIDE NEW WHERE NOT. EXTEND/TRIM TRANSFER ALL EXISTING CIRCUITS FROM REMOVED PANEL 'A' TO NEW PANEL 'BP1'. VERIFY ALL EXISTING LOADS TO REMAIN PRIOR TO COMMENCEMENT OF WORK. BRANCH WIRING TO BE REUSED WHERE POSSIBLE, PROVIDE NEW WHERE NOT. EXTEND/TRIM EXISTING CONDUCTORS AS REQUIRED TO TERMINATE AT NEW PANEL 'BP1'. REFER TO PANEL SCHEDULES ON DRAWING E-108 FOR ADDITIONAL LOADS. TRANSFER OF LOADS TO OCCUR AFTER STORE HOURS OF OPERATION. COORDINATE OUTAGES WITH THE OWNER'S SITE REPRESENTATIVE PRIOR TO COMMENCEMENT OF WORK. NSLC FACILITY IS TO REMAIN OPERATIONAL DURING CONSTRUCTION. REFER TO SPECIFICATION FOR PHASING DETAILS. 3. TRANSFER ALL EXISTING CIRCUITS FROM REMOVED 'W' TO PANEL 'BP2'. VERIFY ALL EXISTING LOADS TO REMAIN PRIOR TO COMMENCEMENT OF WORK. BRANCH WIRING TO BE REUSED WHERE POSSIBLE, PROVIDE NEW WHERE NOT. EXTEND/TRIM EXISTING TRANSFER ALL EXISTING CIRCUITS FROM REMOVED 'W' TO PANEL 'BP2'. VERIFY ALL EXISTING LOADS TO REMAIN PRIOR TO COMMENCEMENT OF WORK. BRANCH WIRING TO BE REUSED WHERE POSSIBLE, PROVIDE NEW WHERE NOT. EXTEND/TRIM EXISTING CONDUCTORS AS REQUIRED TO TERMINATE AT NEW PANEL 'BP2'. REFER TO PANEL SCHEDULES ON DRAWING E-108 FOR ADDITIONAL LOADS. TRANSFER OF LOADS TO OCCUR AFTER STORE HOURS OF OPERATION. COORDINATE OUTAGES WITH THE OWNER'S SITE REPRESENTATIVE PRIOR TO COMMENCEMENT OF WORK. NSLC FACILITY IS TO REMAIN OPERATIONAL DURING CONSTRUCTION. REFER TO SPECIFICATION FOR PHASING DETAILS. 4. MOUNTING LOCATIONS FOR NEW POS PAC POLE, WIRING DEVICES, TELECOMMUNICATIONS OUTLETS AND MILLWORK INTEGRAL CABINET HEATER TO BE COORDINATED WITH OWNER'S SITE REPRESENTATIVE PRIOR TO COMMENCEMENT OF WORK. REFER TO MOUNTING LOCATIONS FOR NEW POS PAC POLE, WIRING DEVICES, TELECOMMUNICATIONS OUTLETS AND MILLWORK INTEGRAL CABINET HEATER TO BE COORDINATED WITH OWNER'S SITE REPRESENTATIVE PRIOR TO COMMENCEMENT OF WORK. REFER TO ARCHITECTURAL DRAWINGS FOR ELEVATIONS OF MILLWORK FOR MOUNTING LOCATIONS OF POS LOCATED EQUIPMENT AND DEVICES. 5. PROVIDE ONE(1) TRIPLE CHANNEL PAC POLE TO FEED NEW POS WIRING DEVICES, HEATER, TAPE LIGHTING, ETC. PAC POLE TO EXTEND FROM ACCESSIBLE CEILING SPACE TO POS MILLWORK. PAC POLE TO BE SIZED AS SMALL AS POSSIBLE WHILST PROVIDE ONE(1) TRIPLE CHANNEL PAC POLE TO FEED NEW POS WIRING DEVICES, HEATER, TAPE LIGHTING, ETC. PAC POLE TO EXTEND FROM ACCESSIBLE CEILING SPACE TO POS MILLWORK. PAC POLE TO BE SIZED AS SMALL AS POSSIBLE WHILST ENSURING CONDUIT FILL RATIOS ARE NOT EXCEEDED. 6. SUPPLY AND INSTALL ONE(1) 5kVA WALL MOUNTED UPS. 5KVA UPS TO FEED PANEL 'S' IN ELECTRICAL ROOM. STANDARD OF ACCEPTANCE: LIEBERT MODEL #GXT5-5000MVRT4UXL. REFER TO DETAIL 2 ON DRAWING E-106 FOR SINGLE LINE DIAGRAM. SUPPLY AND INSTALL ONE(1) 5kVA WALL MOUNTED UPS. 5KVA UPS TO FEED PANEL 'S' IN ELECTRICAL ROOM. STANDARD OF ACCEPTANCE: LIEBERT MODEL #GXT5-5000MVRT4UXL. REFER TO DETAIL 2 ON DRAWING E-106 FOR SINGLE LINE DIAGRAM. INPUT POWER CONNECTION FOR LIEBERT MODEL: HARDWIRED TERMINAL BLOCK - THREE(3) WIRE + GROUND (L-L-N-G). PROVIDE ALL REQUIRED HARDWARE AND SUPPORTS TO WALL MOUNT UPS. 7. WALL MOUNTED DEVICES ARE TO BE INSTALLED IN PREFABRICATED CUT OUTS IN MODULAR WALL SYSTEM. REFER TO LEGEND AND SPECIFICATION FOR MULTMEDIA DEVICE DETAILS, TV RECESSED MULTIMEDIA BOX TO BE MOUNTED APPROX. 84" AFF. WALL MOUNTED DEVICES ARE TO BE INSTALLED IN PREFABRICATED CUT OUTS IN MODULAR WALL SYSTEM. REFER TO LEGEND AND SPECIFICATION FOR MULTMEDIA DEVICE DETAILS, TV RECESSED MULTIMEDIA BOX TO BE MOUNTED APPROX. 84" AFF. COORDINATE MOUNTING OF MULTIMEDIA BOX WITH TV MOUNTING FRAME PRIOR TO ROUGH-IN. RECEPTACLES TO BE MOUNTED IN STANDARD SINGLE GANG DEVICE BOXES. FEED POWER AND COMMUNICATIONS CABLING THROUGH MODULAR WALL SYSTEM. 8. RECONNECT NEW SIGN TO EXISTING CIRCUIT CONTROLLED VIA TIME CLOCK. RECONNECT NEW SIGN TO EXISTING CIRCUIT CONTROLLED VIA TIME CLOCK. 9. PROVIDE POWER AND DATA TO TWO(2) TEMPORARY POS COUNTERS DURING CONSTRUCTION AS A PART OF THE PHASING SCOPE OF WORK. AT A TIME AND LOCATION AS DIRECTED BY THE OWNER'S SITE REPRESENTATIVE, SUPPLY AND INSTALL THE PROVIDE POWER AND DATA TO TWO(2) TEMPORARY POS COUNTERS DURING CONSTRUCTION AS A PART OF THE PHASING SCOPE OF WORK. AT A TIME AND LOCATION AS DIRECTED BY THE OWNER'S SITE REPRESENTATIVE, SUPPLY AND INSTALL THE FOLLOWING PER ONE(1) POS COUNTER: PROVIDE ONE(1) 15A, 125V, ISOLATED GROUND DUPLEX RECEPTACLE(5-15R); FEED ISOLATED GROUND RECEPTACLE FROM UPS FED CIRCUIT IN PANEL 'S'. EACH ISOLATED GROUND RECEPTACLE TO HAVE A DEDICATED CIRCUIT. PROVIDE ONE(1) 15A, 125V, DUPLEX RECEPTACLE FED FROM NORMAL BRANCH PANEL 'BP1'. PROVIDE TWO(2) DATA DROPS AND ONE(1) VOICE DROP. PROVIDE ONE(1) PAC POLE PER COUNTER TO RUN POWER AND TELECOM SERVICES; STANDARD OF ACCEPTANCE: LEGRAND WIREMOLD - ROUND TELE-POWER POLE - ALUMINUM ANODIZED FINISH. PAC POLE TO EXTEND FROM SUSPENDED CEILING TO MILLWORK. REFER TO ARCHITECTURAL DRAWINGS FOR TEMPORARY POS MILLWORK ELEVATIONS OF MOUNTING LOCATIONS FOR WIRING DEVICES. LOCATIONS OF TEMPORARY POS COUNTERS TO BE DETERMINED ON SITE WHEN REQUIRED. LOCATIONS FOR THE TEMPORARY POS ARE TO BE RELOCATABLE; PROVIDE SUFFICIENT CABLE SLACK FOR POWER AND TELECOMMUNICATIONS WIRE/CABLING FOR POS RELOCATION OF UP TO 20' IN ALL DIRECTIONS. COIL CABLE SLACK NEATLY ABOVE SUSPENDED CEILING. 10. FIELD LOCATE DISCONNECTS FOR MECHANICAL EQUIPMENT TO ENSURE ACCEPTABLE WORKING CLEARANCES ARE MAINTAINED. FIELD LOCATE DISCONNECTS FOR MECHANICAL EQUIPMENT TO ENSURE ACCEPTABLE WORKING CLEARANCES ARE MAINTAINED. 11. EVAP-1 FED FROM EXTERIOR COND-1. PROVIDE CONNECTION TO INTERIOR EVAPORATOR AS PER MANUFACTURER INSTRUCTIONS. EVAP-1 FED FROM EXTERIOR COND-1. PROVIDE CONNECTION TO INTERIOR EVAPORATOR AS PER MANUFACTURER INSTRUCTIONS. 12. REFER TO ARCHITECTURAL DRAWINGS FOR POS MILLWORK ELEVATIONS. CONFIRM MOUNTING LOCATIONS OF DEVICES WITH THE OWNER'S SITE REPRESENTATIVE PRIOR ROUGH-IN. WIRE/CABLE TO BE FED FROM ADJACENT WALL INTO POS MILLWORK CHASE. REFER TO ARCHITECTURAL DRAWINGS FOR POS MILLWORK ELEVATIONS. CONFIRM MOUNTING LOCATIONS OF DEVICES WITH THE OWNER'S SITE REPRESENTATIVE PRIOR ROUGH-IN. WIRE/CABLE TO BE FED FROM ADJACENT WALL INTO POS MILLWORK CHASE. STRUCTURED CABLING TO BE FED FROM APPROPRIATE PATCH PANEL IN THE EXISTING TELECOM RACK. 13. RECONNECT EXISTING FAN CIRCUIT TO NEW HYDRONIC HEATER FAN MOTOR. RECONNECT EXISTING FAN CIRCUIT TO NEW HYDRONIC HEATER FAN MOTOR. 14. INSTALL MICROWAVE RECEPTACLE INSIDE MILLWORK CABINET. CONFIRM LOCATION/HEIGHT PRIOR TO ROUGH-IN. INSTALL MICROWAVE RECEPTACLE INSIDE MILLWORK CABINET. CONFIRM LOCATION/HEIGHT PRIOR TO ROUGH-IN. PROVIDE PEDESTAL MOUNTED. 15. PROVIDE PROVIDE A PEDESTAL MOUNTED RECEPTACLE MOUNTED ADJACENT TO RTU. COORDINATE LOCATION ON SITE PRIOR TO ROUGH-IN.PROVIDE PROVIDE A PEDESTAL MOUNTED RECEPTACLE MOUNTED ADJACENT TO RTU. COORDINATE LOCATION ON SITE PRIOR TO ROUGH-IN.

AutoCAD SHX Text

RELOCATED METERING CABINET

AutoCAD SHX Text

PANEL 'DP1' (SEE NOTE 1)

AutoCAD SHX Text

PANEL 'BP1' (SEE NOTE 2)

AutoCAD SHX Text

PANEL 'S'

AutoCAD SHX Text

RELOCATED TELECOM DEMARCATION

AutoCAD SHX Text

PAC POLE (SEE NOTE 4 & 5)

AutoCAD SHX Text

SEE NOTE 7

AutoCAD SHX Text

SEE NOTE 8

AutoCAD SHX Text

PANEL 'BP2' (SEE NOTE 3)

AutoCAD SHX Text

EXISTING TELECOM CABINET

AutoCAD SHX Text

5kV UPS (SEE NOTE 6)

AutoCAD SHX Text

SEE NOTE 4

AutoCAD SHX Text

SEE NOTE 12

AutoCAD SHX Text

M

AutoCAD SHX Text

RELOCATED UTILITY METER

AutoCAD SHX Text

2

AutoCAD SHX Text

-

AutoCAD SHX Text

COND-1 BP1-49,51 (SEE NOTE 10)

AutoCAD SHX Text

EVAP-1 (SEE NOTE 11)

AutoCAD SHX Text

ROOF TOP MOUNTED (SEE NOTE 10) (TYPICAL)

AutoCAD SHX Text

TWO(2) TEMPORARY POS COUNTERS (SEE NOTE 9)

AutoCAD SHX Text

RECONNECT NEW AUTOMATIC DOOR

AutoCAD SHX Text

IDS PANEL

AutoCAD SHX Text

48" AFF (SEE NOTE 14)

AutoCAD SHX Text

36" AFF

AutoCAD SHX Text

48" AFF

AutoCAD SHX Text

SEE NOTE 13

AutoCAD SHX Text

REUSE EXISTING CIRCUIT. PROVIDE NEW BRANCH WIRING. 24" AFF.

AutoCAD SHX Text

200A,100% RATED 208V, 3P,4W

AutoCAD SHX Text

MAIN DISCONNECT C/W SERVICE ENTRANCE 100% RATED CIRCUIT BREAKER, BOTTOM FED

AutoCAD SHX Text

S

AutoCAD SHX Text

MSS

AutoCAD SHX Text

T

AutoCAD SHX Text

ER

AutoCAD SHX Text

ER

AutoCAD SHX Text

ALL DEVICES TO BE SURFACE MOUNTED.

AutoCAD SHX Text

BP1-55

AutoCAD SHX Text

EF-1

AutoCAD SHX Text

CL

AutoCAD SHX Text

S

AutoCAD SHX Text

MSS

AutoCAD SHX Text

3

AutoCAD SHX Text

3

AutoCAD SHX Text

ROOFTOP PEDESTAL MOUNTED GFI RECEPTACLE (SEE NOTE 15)

AutoCAD SHX Text

3

AutoCAD SHX Text

3

DRAW

ING

NAM

E: K

:\PR

OJE

CTS\

2006

13.0

6 N

SLC

BERW

ICK

BWS\

20 C

AD\0

5 EL

EC\2

0061

3.06

- ES

K-01

.DW

G L

AYO

UT

NAM

E: 2

0061

3.06

- ES

K-01

PLO

T DA

TE:D

ecem

ber 1

5, 2

020

3:34

:06

PM C

AD O

PERA

TOR:

RM

ANTE

UFF

EL

ScaleDate Designed Approved ContractCheckedDrawn CBCL No.

BERWICK NSLC SELECT STORE - INTERIOR RENOVATION

ROOFTOP PEDESTAL MOUNTED GFI RECEPTACLE

Drawing

ESK-012020.12.15 N.T.S. REM REM JAS - 200613.06

DETAIL - ROOFTOP PEDESTAL GFI RECEPTACLE

1-

N.T.S.

AutoCAD SHX Text

1/4" x 8" x 2-3/4" ALUMINUM BRACKET PLATE WELDED TO 1/4" THICK ROUND PLATE USING 1/4" FILLET WELD.

AutoCAD SHX Text

LIQUID TIGHT COROGRIPS STRAIGHT THROUHG 1/2" NPT FITTING; NYLON.

AutoCAD SHX Text

DRILL AND TAP THROUGH 6mm THICK ROUND PLATE FOR 1/2" NPT FITTING.

AutoCAD SHX Text

THREADED STEEL CAP.

AutoCAD SHX Text

T-TYPE LOCKING HANDLES.

AutoCAD SHX Text

STACK JACK ALUMINUM FLASHING.

AutoCAD SHX Text

EPDM BASE SEAL BONDED TO METAL SLEEVE.

AutoCAD SHX Text

JUNCTION BOX MOUNTED AT UNDERSIDE OF ROOF DECK.

AutoCAD SHX Text

WHEATHERPROOF WHILE-IN-USE COVER PLATE, CSA TYPE 3R.

AutoCAD SHX Text

CSA TYPE 5-20R RECEPTACLE FED FROM GFCI-TYPE BREAKER.

AutoCAD SHX Text

PVC-COATED ALUMINUM FD OUTLET BOX WITH NEOPRENE GASKET.

AutoCAD SHX Text

1/2" LIQUID TIGHT FLEXIBLE CONDUIT.

AutoCAD SHX Text

2" PVC-COATED SCHEDULE 40 GALVANIZED STEEL PIPE.

AutoCAD SHX Text

3/4" STAINLESS STEEL LOCK BOLTS WITH EPDM SEAL.

AutoCAD SHX Text

6-1/2" DIA. x 1/4" x 13-1/4" HIGH URETHANE-INSULATED PIPE WELDED TO 3/4" x 14" x 14" STEEL PLATE.

AutoCAD SHX Text

EMDED DECK FLANGE IN LAYER OF PLASTIC CEMENT (BUR).

AutoCAD SHX Text

1/2" LIQUID TIGHT FLEXIBLE CONDUIT.

ABCEFG

1

2

3

NEW CONSTRUCTION - HVAC

1-

3/16"=1'-0"

SCALE:

PROJECT #:

DRAWN BY:

DRAWING #:

SEAL:

CLIENT:

PROJECT:

TITLE:


NORTH ARROW:

ISSUED/REVISIONS:

Contact:



T 902-421-7241

F 902-423-3938

www.cbcl.ca


STEPHEN BAYERT. 902-450-5916F. 902-450-6116



MECHANICAL NEWCONSTRUCTION

CBCL

200613.06

AS NOTED

M-200-R1

AutoCAD SHX Text

WALL HEATER

AutoCAD SHX Text

26"x12"

AutoCAD SHX Text

20"x12"

AutoCAD SHX Text

26"x12"

AutoCAD SHX Text

14"x10"

AutoCAD SHX Text

12"x10"

AutoCAD SHX Text

12"x10"

AutoCAD SHX Text

12"

AutoCAD SHX Text

10"

AutoCAD SHX Text

10"

AutoCAD SHX Text

1-1/2"

AutoCAD SHX Text

1-1/2"

AutoCAD SHX Text

3/4"

AutoCAD SHX Text

3/4"

AutoCAD SHX Text

BPB-1

AutoCAD SHX Text

NEW BYPASS BOX C/W 2KW ELECTRIC REHEAT COIL

AutoCAD SHX Text

T

AutoCAD SHX Text

200

AutoCAD SHX Text

S-1

AutoCAD SHX Text

EVAP-1

AutoCAD SHX Text

COND-1

AutoCAD SHX Text

FFUH-1

AutoCAD SHX Text

150

AutoCAD SHX Text

S-1

AutoCAD SHX Text

265

AutoCAD SHX Text

S-1

AutoCAD SHX Text

265

AutoCAD SHX Text

S-1

AutoCAD SHX Text

265

AutoCAD SHX Text

S-1

AutoCAD SHX Text

265

AutoCAD SHX Text

S-1

AutoCAD SHX Text

265

AutoCAD SHX Text

S-1

AutoCAD SHX Text

265

AutoCAD SHX Text

S-1

AutoCAD SHX Text

265

AutoCAD SHX Text

S-1

AutoCAD SHX Text

-

AutoCAD SHX Text

R-1

AutoCAD SHX Text

-

AutoCAD SHX Text

R-1

AutoCAD SHX Text

-

AutoCAD SHX Text

R-1

AutoCAD SHX Text

-

AutoCAD SHX Text

R-1

AutoCAD SHX Text

-

AutoCAD SHX Text

R-1

AutoCAD SHX Text

NEW 24X24 DIFFUSER. SEE SCHEDULE ON DWG M-300. CONNECT TO EXISTING DUCTWORK. (TYP. 9) COORDINATE EXACT LOCATIONS W/ ARCHITECTURAL RCP.

AutoCAD SHX Text

ROUTE NEW 1" CONDENSATE PIPING FROM EVAP-1 THROUGH EXTERIOR WALL DOWN TO GRADE. SLOPE PIPING IN DIRECTION OF FLOW.

AutoCAD SHX Text

NEW THERMOSTAT MOUNTED AT 5'-0" A.F.F

AutoCAD SHX Text

SUPPORT EXTERIOR CONDENSING UNIT w/ STAINLESS STEEL BRACKETS SECURED TO WALL

AutoCAD SHX Text

NEW 24X24 R/A GRILLE. (TYP. 7) SEE SCHEDULE ON DWG M-300.

AutoCAD SHX Text

EXISTING ROOF CURB AND DUCTWORK TO REMAIN. INSTALL ADAPTOR CURB TO SUIT C/W FASTENERS, FLASHING, AND SEALS TO ENSURE A WATERTIGHT CONNECTION IN ACCORDANCE WITH SMACNA AND AHU MANUFACTURER'S INSTRUCTIONS

AutoCAD SHX Text

HVAC NOTES: 1. AIRFLOW VALUES INDICATED ON DRAWING IS BASED ON EXISTING DESIGN DRAWINGS. AIRFLOW VALUES INDICATED ON DRAWING IS BASED ON EXISTING DESIGN DRAWINGS. 2. AIR BALANCING CONTRACTOR TO BALANCE AIRFLOWS TO THE VALUES INDICATED. NOTIFY ENGINEER OF ANY DISCREPANCIES. AIR BALANCING CONTRACTOR TO BALANCE AIRFLOWS TO THE VALUES INDICATED. NOTIFY ENGINEER OF ANY DISCREPANCIES. 3. COORDINATE DIFFUSER LOCATION WITH ELECTRICAL LIGHT FIXTURES PRIOR TO ROUGH-IN. CONFIRM LOCATION WITH THE OWNER'S COORDINATE DIFFUSER LOCATION WITH ELECTRICAL LIGHT FIXTURES PRIOR TO ROUGH-IN. CONFIRM LOCATION WITH THE OWNER'S SITE REPRESENTATIVE PRIOR TO COMMENCEMENT OF WORK.

AutoCAD SHX Text

AHU-1

AutoCAD SHX Text

75

AutoCAD SHX Text

S-1

AutoCAD SHX Text

BB-1

AutoCAD SHX Text

NEW BASEBOARD HEATER. SEE SCHEDULE ON M-300. COORDINATE EXACT LOCATION WITH MILLWORK.

AutoCAD SHX Text

CONNECT TO EXISTING 1-1/2" TAKEOFFS. INSULATE NEW BRANCH PIPING TO BB-1

AutoCAD SHX Text


AutoCAD SHX Text

PROVIDE NEW WALL CAPS FOR WASHROOMS AND JANITOR'S CLOSET (3 TYP.), BLACK IN COLOR. SIZE MATCH EXISTING DUCT DIMENSIONS.

AutoCAD SHX Text


AutoCAD SHX Text

-

AutoCAD SHX Text

R-2

AutoCAD SHX Text

-

AutoCAD SHX Text

R-2

AutoCAD SHX Text

T

AutoCAD SHX Text

RELOCATED THERMOSTAT FOR PERIMETER HEATING

AutoCAD SHX Text

REINSTALL PERIMETER HYDRONIC HEATER AFTER WALL REPAIRS HAVE BEEN COMPLETED.

AutoCAD SHX Text

T

AutoCAD SHX Text

NEW HYDRONIC FAN-FORCED UNIT HEATER. SEE SCHEDULE ON DWG M-300. CONNECT TO EXISTING PIPING. SEE DETAIL 5, DWG. M-300

AutoCAD SHX Text

NEW AHU-1 CONTROLLER

AutoCAD SHX Text

T

AutoCAD SHX Text

T

AutoCAD SHX Text

MOUNTED IN TBAR (SEE NOTE 3)

AutoCAD SHX Text

NEW EXHAUST FAN EF-1

AutoCAD SHX Text

NEW 12x12 EXHAUST DUCT C/W FIRE DAMPER

AutoCAD SHX Text

T

AutoCAD SHX Text

-

AutoCAD SHX Text

E-2

AutoCAD SHX Text

NEW LOW VOLTAGE REVERSE ACTING THERMOSTAT

AutoCAD SHX Text


AutoCAD SHX Text

%%ULAYOUT:

AutoCAD SHX Text

K:\Projects\200613.06 NSLC BERWICK BWS\20 CAD\04 MECH\M-200 MECHANICAL NEW CONSTRUCTION.dwg

AutoCAD SHX Text

%%UDATE:

AutoCAD SHX Text

December 9, 2020 4:40:16 PM

AutoCAD SHX Text

M-200 MECHANICAL NEW CONSTRUCTION

AutoCAD SHX Text

No.

AutoCAD SHX Text

Remarks

AutoCAD SHX Text

Date

AutoCAD SHX Text


AutoCAD SHX Text

GENERAL NOTES:

AutoCAD SHX Text

CONSULTANTS:

AutoCAD SHX Text

A

AutoCAD SHX Text

B

AutoCAD SHX Text

C

AutoCAD SHX Text

D

AutoCAD SHX Text

4

AutoCAD SHX Text

2

AutoCAD SHX Text

1

AutoCAD SHX Text

3

AutoCAD SHX Text


AutoCAD SHX Text

01

AutoCAD SHX Text

2020.10.16

AutoCAD SHX Text

ISSUED FOR REVIEW

AutoCAD SHX Text

02

AutoCAD SHX Text

2020.11.27

AutoCAD SHX Text

03

AutoCAD SHX Text

2020.12.15

AutoCAD SHX Text

ISSUED FOR TENDER

AutoCAD SHX Text

ADDENDUM NO.1

AutoCAD SHX Text

1

SCALE:

PROJECT #:

DRAWN BY:

DRAWING #:

SEAL:

CLIENT:

PROJECT:

TITLE:


NORTH ARROW:

ISSUED/REVISIONS:

Contact:



T 902-421-7241

F 902-423-3938

www.cbcl.ca


STEPHEN BAYERT. 902-450-5916F. 902-450-6116



MECHANICAL DETAILS& SCHEDULES

CBCL

200613.06

AS NOTED

M-300-R1

AutoCAD SHX Text


AutoCAD SHX Text

%%ULAYOUT:

AutoCAD SHX Text

K:\Projects\200613.06 NSLC BERWICK BWS\20 CAD\04 MECH\M-300 MECHANICAL DETAILS & SCHEDULES.dwg

AutoCAD SHX Text

%%UDATE:

AutoCAD SHX Text

December 9, 2020 4:40:19 PM

AutoCAD SHX Text

M-300 MECHANICAL DETAILS & SCHEDULES

AutoCAD SHX Text

No.

AutoCAD SHX Text

Remarks

AutoCAD SHX Text

Date

AutoCAD SHX Text


AutoCAD SHX Text

GENERAL NOTES:

AutoCAD SHX Text

CONSULTANTS:

AutoCAD SHX Text

A

AutoCAD SHX Text

B

AutoCAD SHX Text

C

AutoCAD SHX Text

D

AutoCAD SHX Text

4

AutoCAD SHX Text

2

AutoCAD SHX Text

1

AutoCAD SHX Text

3

AutoCAD SHX Text


AutoCAD SHX Text

01

AutoCAD SHX Text

2020.10.16

AutoCAD SHX Text

ISSUED FOR REVIEW

AutoCAD SHX Text

02

AutoCAD SHX Text

2020.11.27

AutoCAD SHX Text

03

AutoCAD SHX Text

2020.12.15

AutoCAD SHX Text

ISSUED FOR TENDER

AutoCAD SHX Text

ADDENDUM NO.1

AutoCAD SHX Text

GRILLE & DIFFUSER SCHEDULE

AutoCAD SHX Text

DESIG.

AutoCAD SHX Text

TYPE

AutoCAD SHX Text

MFGR.

AutoCAD SHX Text

MODEL

AutoCAD SHX Text

SIZE

AutoCAD SHX Text

NECK

AutoCAD SHX Text

COMMENTS

AutoCAD SHX Text

S-1

AutoCAD SHX Text

ROUND CEILING DIFFUSER

AutoCAD SHX Text

NAILOR

AutoCAD SHX Text

RBD

AutoCAD SHX Text

-

AutoCAD SHX Text

250

AutoCAD SHX Text

SPUN ALUMINUM, WHITE FINISH, INTEGRAL BALANCING DAMPER

AutoCAD SHX Text

S-2

AutoCAD SHX Text

SQUARE SUPPLY GRILLE

AutoCAD SHX Text

NAILOR

AutoCAD SHX Text

67SH

AutoCAD SHX Text

250x250

AutoCAD SHX Text

-

AutoCAD SHX Text

304 STAINLESS STEEL, SINGLE DEFLECTION, INTEGRAL BALANCING DAMPER

AutoCAD SHX Text

S-3

AutoCAD SHX Text


AutoCAD SHX Text

NAILOR

AutoCAD SHX Text

RNS

AutoCAD SHX Text

300x300

AutoCAD SHX Text

150

AutoCAD SHX Text


AutoCAD SHX Text

S-4

AutoCAD SHX Text


AutoCAD SHX Text

NAILOR

AutoCAD SHX Text

RNS

AutoCAD SHX Text

600x600

AutoCAD SHX Text

250

AutoCAD SHX Text


AutoCAD SHX Text

R-1

AutoCAD SHX Text

EGGCRATE GRILLE

AutoCAD SHX Text

NAILOR

AutoCAD SHX Text

51EC

AutoCAD SHX Text

600x600

AutoCAD SHX Text

-

AutoCAD SHX Text

ALUMINUM CORE / FRAME, WHITE FINISH, LAY-IN T-BAR

AutoCAD SHX Text

E-1

AutoCAD SHX Text

FIXED BLADE GRILLE

AutoCAD SHX Text

NAILOR

AutoCAD SHX Text

5145

AutoCAD SHX Text

150x150

AutoCAD SHX Text

-

AutoCAD SHX Text

ALUMINUM BAR GRILLE, WHITE FINISH, INTEGRAL BALANCING DAMPER

AutoCAD SHX Text

E-2

AutoCAD SHX Text

FIXED BLADE GRILLE

AutoCAD SHX Text

NAILOR

AutoCAD SHX Text

5145

AutoCAD SHX Text

300x300

AutoCAD SHX Text

-

AutoCAD SHX Text

ALUMINUM BAR GRILLE, WHITE FINISH

AutoCAD SHX Text

BYPASS BOX SCHEDULE

AutoCAD SHX Text

DESIG.

AutoCAD SHX Text

MFGR.

AutoCAD SHX Text

MODEL

AutoCAD SHX Text

INLET DIAMETER (in.)

AutoCAD SHX Text

MAX CAPACITY (CFM)

AutoCAD SHX Text

COMMENTS

AutoCAD SHX Text

BPB-1

AutoCAD SHX Text

NAILOR

AutoCAD SHX Text

D34RE

AutoCAD SHX Text

6"

AutoCAD SHX Text

0-400

AutoCAD SHX Text

ANALOG BYPASS BOX, SEQUENCE OF OPERATIONS 'E6': AUTOMATIC HEATING / COOLING CHANGEOVER WITH PROPORTIONAL ELECTRIC HEAT, 2 KW @ 208/1/60, LOW VOLTAGE ACTUATOR, WALL-MOUNTED THERMOSTAT, 120V w/ INTEGRAL TRANSFORMER. SET MIN. POSITION TO 20%.

AutoCAD SHX Text

SPLIT SYSTEM HEAT PUMP SCHEDULE

AutoCAD SHX Text

DESIG.

AutoCAD SHX Text

LOCATION

AutoCAD SHX Text

MANUFACTURER

AutoCAD SHX Text

MODEL

AutoCAD SHX Text

REFRIGERANT

AutoCAD SHX Text

NOMINAL CAPACITY

AutoCAD SHX Text

HEATING

AutoCAD SHX Text

COOLING

AutoCAD SHX Text

AIR FLOW

AutoCAD SHX Text

POWER

AutoCAD SHX Text

UNIT MCA

AutoCAD SHX Text

COMMENTS

AutoCAD SHX Text

EVAP-1

AutoCAD SHX Text

OFFICE 103

AutoCAD SHX Text

MITSUBISHI

AutoCAD SHX Text

MSZ-GL12NA-U1

AutoCAD SHX Text

R410A

AutoCAD SHX Text

1 TON

AutoCAD SHX Text

12000 Btu/h

AutoCAD SHX Text

14400 Btu/h

AutoCAD SHX Text

237

AutoCAD SHX Text

208/1/60

AutoCAD SHX Text

1

AutoCAD SHX Text

c/w WIRED WALL CONTROLLER.

AutoCAD SHX Text

COND-1

AutoCAD SHX Text

OUTDOOR SECTION

AutoCAD SHX Text

MITSUBISHI

AutoCAD SHX Text

MUZ-GL12NA

AutoCAD SHX Text

R410A

AutoCAD SHX Text

1 TON

AutoCAD SHX Text

-

AutoCAD SHX Text

-

AutoCAD SHX Text

-

AutoCAD SHX Text

208/1/60

AutoCAD SHX Text

9

AutoCAD SHX Text

L

AutoCAD SHX Text

W L = 1/4 OF "W"

AutoCAD SHX Text

AIRFLOW

AutoCAD SHX Text

45°

AutoCAD SHX Text

1

AutoCAD SHX Text

-

AutoCAD SHX Text

TYPICAL DIFFUSER

AutoCAD SHX Text

DETAIL-

AutoCAD SHX Text

N.T.S.

AutoCAD SHX Text

2

AutoCAD SHX Text

-

AutoCAD SHX Text

TYP. TAKE-OFF BOOT ON SUPPLY TO DIFFUSER

AutoCAD SHX Text

DETAIL-

AutoCAD SHX Text

N.T.S.

AutoCAD SHX Text

NOTE: FLEX DUCT SHALL NOT BE USED ON BRANCH DUCTING TO DIFFUSERS IN ROOMS WITHOUT CEILINGS.

AutoCAD SHX Text

S/A

AutoCAD SHX Text

EYE SCREW

AutoCAD SHX Text

#12 WIRE

AutoCAD SHX Text

RIGID DUCT ELBOW

AutoCAD SHX Text

CEILING DIFFUSER SEE PLANS & SCHEDULE

AutoCAD SHX Text

CONNECT FLEXIBLE DUCT TO COLLAR WITH 22 GAUGE CLAMP & FOUR SHEET METAL SCREWS & SEAL WITH DUCT TAPE

AutoCAD SHX Text

CEILING

AutoCAD SHX Text

MINIMUM RADIUS EQUAL TO ONE DUCT DIAMETER

AutoCAD SHX Text

FLEXIBLE DUCT, SEE PLANS FOR SIZE

AutoCAD SHX Text

25MM X 22 GAUGE BAND

AutoCAD SHX Text

BALANCING DAMPER, TYPICAL

AutoCAD SHX Text

W

AutoCAD SHX Text

L = 1/4 OF "W"

AutoCAD SHX Text

L

AutoCAD SHX Text

45%%D

AutoCAD SHX Text

AIR FLOW

AutoCAD SHX Text

MAIN

AutoCAD SHX Text

DUCT

AutoCAD SHX Text

SUPPLIED WITH BOX

AutoCAD SHX Text

ATTENUATOR

AutoCAD SHX Text

TIMES INLET DIA.

AutoCAD SHX Text

LENGTH TO BE 2

AutoCAD SHX Text

RIGID ROUND DUCT

AutoCAD SHX Text

ACTUATOR

AutoCAD SHX Text

AS REQUIRED.

AutoCAD SHX Text

DISCHARGE DUCT SIZE

AutoCAD SHX Text

B.D.

AutoCAD SHX Text

ACCESS PANEL

AutoCAD SHX Text

ELECTRONIC

AutoCAD SHX Text

MIN. 2 TIMES DUCT WIDTH.

AutoCAD SHX Text

3

AutoCAD SHX Text

-

AutoCAD SHX Text

N.T.S.

AutoCAD SHX Text

TYP. BYPASS BOX TERMINAL UNIT CONNECTION

AutoCAD SHX Text

DETAIL-

AutoCAD SHX Text

FORCE FLOW HEATER SCHEDULE

AutoCAD SHX Text

DESIG.

AutoCAD SHX Text

MANUFACTURER

AutoCAD SHX Text

MODEL

AutoCAD SHX Text

ARRANGEMENT

AutoCAD SHX Text

HEAT OUTPUT

AutoCAD SHX Text

EWT

AutoCAD SHX Text

LWT

AutoCAD SHX Text

AIRFLOW

AutoCAD SHX Text

MOTOR POWER

AutoCAD SHX Text

COMMENTS

AutoCAD SHX Text

FFUH-1

AutoCAD SHX Text

AIRTEX

AutoCAD SHX Text

CUH SERIES

AutoCAD SHX Text

19

AutoCAD SHX Text

47 MBH

AutoCAD SHX Text

180 F

AutoCAD SHX Text

160 F

AutoCAD SHX Text

620 CFM

AutoCAD SHX Text

120V/1

AutoCAD SHX Text

SEMI-RECESSED MODEL, INTEGRAL THERMOSTAT, UNIT DIMENSIONS TO SUIT ROUGH OPENING OF EXISTING (35" H x 45" W). DETERMINE EXACT DIMENSIONS ONSITE PRIOR TO ORDER

AutoCAD SHX Text

4

AutoCAD SHX Text

-

AutoCAD SHX Text

FORCE FLOW CABINET HEATER PIPING

AutoCAD SHX Text

DETAIL-

AutoCAD SHX Text

N.T.S.

AutoCAD SHX Text

WALL HUNG FULLY RECESSED CABINET

AutoCAD SHX Text

FRONT INLET

AutoCAD SHX Text

OUTLINE OF COIL AND FILTER SECTION

AutoCAD SHX Text

FRONT DISCHARGE

AutoCAD SHX Text

EXISTING ISOLATION VALVES

AutoCAD SHX Text

UNION

AutoCAD SHX Text

20mm HOSE BIBB

AutoCAD SHX Text

BASEBOARD HEATER SCHEDULE

AutoCAD SHX Text

DESIG.

AutoCAD SHX Text

SERVICE

AutoCAD SHX Text

MANUFACTURER

AutoCAD SHX Text

MODEL

AutoCAD SHX Text

ROWS

AutoCAD SHX Text

HEATING OUTPUT (PER FT)

AutoCAD SHX Text

ELEMENT LENGTH (FT)

AutoCAD SHX Text

EWT

AutoCAD SHX Text

LWT

AutoCAD SHX Text

EAT

AutoCAD SHX Text

COMMENTS

AutoCAD SHX Text

BB-1

AutoCAD SHX Text

HEATING

AutoCAD SHX Text

ENGINEERED AIR

AutoCAD SHX Text

PROFILE SERIES

AutoCAD SHX Text

1

AutoCAD SHX Text

680 BTU

AutoCAD SHX Text

6

AutoCAD SHX Text

180

AutoCAD SHX Text

160

AutoCAD SHX Text

65

AutoCAD SHX Text

COPPER TUBE, ALUMINUM FIN, PAINTED STEEL CABINET WITH END CAPS AND MOUNTING BRACKET

AutoCAD SHX Text

7

AutoCAD SHX Text

-

AutoCAD SHX Text

BASEBOARD RADIATION PIPING

AutoCAD SHX Text

DETAIL-

AutoCAD SHX Text

N.T.S.

AutoCAD SHX Text

X

AutoCAD SHX Text

D

AutoCAD SHX Text

H

AutoCAD SHX Text

D

AutoCAD SHX Text

SCR

AutoCAD SHX Text

T

AutoCAD SHX Text

SEQUENCE OF OPERATION: 1. UNIT TO RECEIVE ITS OWN INDIVIDUAL FULLY MODIFIABLE UNIT TO RECEIVE ITS OWN INDIVIDUAL FULLY MODIFIABLE SCHEDULE COMPLETE WITH NIGHT-TIME SETBACK. COORDINATE SCHEDULE PROGRAMMING WITH OWNER. 2. OCCUPIED MODE: UNIT SHALL MODULATE/STAGE THE HEATING OCCUPIED MODE: UNIT SHALL MODULATE/STAGE THE HEATING AND COOLING SECTIONS TO MAINTAIN SPACE TEMPERATURE SET POINT. 3. UNOCCUPIED MODE: UNIT SHALL BE NORMALLY OFF AND SHALL UNOCCUPIED MODE: UNIT SHALL BE NORMALLY OFF AND SHALL BE ENERGIZED TO MAINTAIN SET POINT. 4. COOLING: DX COOLING SHALL STAGE AS REQUIRED TO ACHIEVE COOLING: DX COOLING SHALL STAGE AS REQUIRED TO ACHIEVE SPACE TEMPERATURE SET POINT. ECONOMIZER COOLING TO BE ENABLED AND CONTROLLED WHEN OUTDOOR AIR TEMPERATURE PERMITS AND SHALL OVERRIDE DX COOLING. 5. HEATING: PRIMARY HEATING SHALL BE PROVIDED BY THE HEAT HEATING: PRIMARY HEATING SHALL BE PROVIDED BY THE HEAT PUMP WITH A SUPPLEMENTAL ELECTRIC COIL (W/ SCR CONTROL) PROVIDING A SECOND STAGE OF HEATING AS REQUIRED.

AutoCAD SHX Text

5

AutoCAD SHX Text

-

AutoCAD SHX Text

N.T.S.

AutoCAD SHX Text

AHU-1 CONTROLS

AutoCAD SHX Text

DETAIL-

AutoCAD SHX Text

ADAPTOR

AutoCAD SHX Text

6"

AutoCAD SHX Text

8"

AutoCAD SHX Text

DRAIN PLUG

AutoCAD SHX Text

AIR HANDLING UNIT OR AIR CONDITIONING UNIT

AutoCAD SHX Text

REMOVABLE PLUG

AutoCAD SHX Text

COOLING COIL DRAIN PAN SECTION

AutoCAD SHX Text

1-1/4" PVC PIPE

AutoCAD SHX Text

NOTE: : CONFIRM TRAP DEPTHS WITH AHU MANUFACTURER.

AutoCAD SHX Text

6

AutoCAD SHX Text

-

AutoCAD SHX Text

N.T.S.

AutoCAD SHX Text

CONDENSATE DRAIN (TYP.)

AutoCAD SHX Text

DETAIL-

AutoCAD SHX Text

AHU-1

AutoCAD SHX Text

NOTE: MATCH EXISTING HEATER DIMENSIONS WHERE POSSIBLE. PROVIDE INFILL PANEL AS REQUIRED WITH INFILL DETAIL REVIEWED AND APPROVED BY ARCHITECT.

AutoCAD SHX Text

SUPPLY

AutoCAD SHX Text

DRAIN VALVE

AutoCAD SHX Text

ECCENTRIC REDUCER

AutoCAD SHX Text

ELEMENT

AutoCAD SHX Text

TYP. (IF REQ'D)

AutoCAD SHX Text

RETURN

AutoCAD SHX Text

BALANCING VALVE

AutoCAD SHX Text

CONTROL VALVE

AutoCAD SHX Text

ISOLATION VALVE

AutoCAD SHX Text

AIR HANDLING UNIT SCHEDULE

AutoCAD SHX Text

TAG

AutoCAD SHX Text

TYPE

AutoCAD SHX Text

LOCATION

AutoCAD SHX Text

MAKE

AutoCAD SHX Text

MODEL NUMBER

AutoCAD SHX Text

TOTAL COOLING CAPACITY (MBH)

AutoCAD SHX Text

HP HEATING CAPACITY (MBH)

AutoCAD SHX Text

ELECTRIC HEATING COIL (KW)

AutoCAD SHX Text

AIRFLOW (CFM)

AutoCAD SHX Text

E.S.P. (IN)

AutoCAD SHX Text

POWER SUPPLY (V/HZ/PH)

AutoCAD SHX Text

MCA (AMP)

AutoCAD SHX Text

MOCP (AMP)

AutoCAD SHX Text

REFRIGERANT TYPE

AutoCAD SHX Text

REMARKS

AutoCAD SHX Text

AHU-1

AutoCAD SHX Text

HEAT PUMP

AutoCAD SHX Text

ROOF

AutoCAD SHX Text

YORK

AutoCAD SHX Text

XXEA7A2C3AA1B111A2

AutoCAD SHX Text

70.8

AutoCAD SHX Text

40.9

AutoCAD SHX Text

16.0

AutoCAD SHX Text

2400.0

AutoCAD SHX Text

1.7

AutoCAD SHX Text

208/3/60

AutoCAD SHX Text

75.8

AutoCAD SHX Text

80

AutoCAD SHX Text

R-410A

AutoCAD SHX Text

C/W ADAPTOR CURB (90 DEG), ECONOMIZER, HIGH STATIC DRIVE, TWO STAGE COMPRESSOR, VFD SUPPLY FAN, INTEGRAL DISCONNECT, 20A CONVENIENCE RECEPTACLE, FIELD MOUNTED CO2 SENSOR. DIGITAL PROGRAMMABLE THERMOSTAT

AutoCAD SHX Text

BALANCING VALVE

AutoCAD SHX Text

CONTROL VALVE

AutoCAD SHX Text

EXHAUST FAN SCHEDULE

AutoCAD SHX Text

DESIG.

AutoCAD SHX Text

LOCATION

AutoCAD SHX Text

MANUFACTURER

AutoCAD SHX Text

MODEL

AutoCAD SHX Text

AIR FLOW

AutoCAD SHX Text

STATIC PRESSURE

AutoCAD SHX Text

SPEED CONTROL

AutoCAD SHX Text

DISC SWITCH

AutoCAD SHX Text

ELECTRICAL

AutoCAD SHX Text

COMMENTS

AutoCAD SHX Text

EF-1

AutoCAD SHX Text

ELECTRICAL ROOM

AutoCAD SHX Text

LOREN COOK

AutoCAD SHX Text

GC-622

AutoCAD SHX Text

460 CFM

AutoCAD SHX Text

0.25 in.-wg.

AutoCAD SHX Text

YES

AutoCAD SHX Text

YES

AutoCAD SHX Text

120V/1PH/60HZ

AutoCAD SHX Text

CABINET FAN c/w RUBBER VIBRATION ISOLATORS, WHITE GRILLE, INSULATED HOUSING & ISOLATORS.

AutoCAD SHX Text

1

AutoCAD SHX Text

1

AutoCAD SHX Text

1

AutoCAD SHX Text

1

AutoCAD SHX Text

1

AutoCAD SHX Text

1

AutoCAD SHX Text

1

AutoCAD SHX Text

1

AutoCAD SHX Text

1

NSLC Reference # CN-39-FY21 Addendum # 5 NSLC BERWICK RENOVATION Approved for Alternate · 2021. 1....

Documents

Transcript of NSLC Reference # CN-39-FY21 Addendum # 5 NSLC BERWICK RENOVATION Approved for Alternate · 2021. 1....