Nitgen NAC 2500 PLUS Fingerprint Access Controller Terminal Installation Manual

8/9/2019 Nitgen NAC 2500 PLUS Fingerprint Access Controller Terminal Installation Manual

1/20

NAC-2500 Terminal InstallationGuide


2/20


3/20

- 4 -

1. Before Installation

1.1 To install

Please follow the installation guide because the performance

can be decreased if the product is installed incorrectly.

1.2 Product package

Product Pictures Qty Use

Terminal 1ea Access Controller

Adapter 1ea

Power cord 1ea

Supplying power for

the terminal

Rear case 1ea Fastening the terminal


4/20

- 5 -

4ea Fastening the terminalBolt

6ea Fastening the rear

case

1ea

5ea

Connecting door cable

S/W CD 1ea


5/20

- 6 -

2. Installation Environment

Please keep in mind the following conditions when you install the

product. You might need to obtain the user's consent if necessary.

This product is originally designed to install indoors. If you

have to install it outdoors, however, do not expose the terminal

to direct sunlight, snow or rain.

The connection cables should not be exposed outside, and it

is highly recommended to bury them underground. If that is

impossible, you must obtain the user's consent beforeinstallation.

Power supply should begin after all connections are completed.

Do not disconnect the lines or make any additional

connections while the power is supplied.

If you install the product as an access controller at a proper

height for the users and in a near place that facilitates control

of the entrance, you can use it more efficiently.

The power requirement for the system is AC 100~240V,

50/60Hz.


6/20

- 7 -

3. System Configuration

3.1 Network mode

Terminals are connected by network and it can be remote

control.

Terminal

Lock


7/20

- 8 -

3.2 Standalone mode

One terminal is used independently. All settings such as user

registration, deletion, and access control are performed in the

terminal alone.

Figure 3.2 Terminal Block Diagram

Locking Device

Door Open S/W

Interphone


8/20

- 9 -

4. Installation

The overall installation procedure is as follows:

Fasten the bracket

Attach other devices except terminal(locking device, interphone,

etc.)

Connect the external cables

Fasten the terminal

4.1 Fastening the auxiliary plate

Decide where you want to install the product, and cut the

rear case as shown Figure 4.1 to make the hole for wiring.

Figure 4.1 Making the hole for wiring in the rear case


9/20

- 10 -

Align the bracket with the hole for wiring as shown Figure

4.2, and fasten it with 6 bolts supported in the packet.

Figure 4.2 Fastening rear case


10/20

- 11 -

4.2 Attaching other devices except terminal

You can attach the following devices. Refer to the specifications

of each device for more information on installation.

Locking device

Door Open button

Types of installable locking devices and specifications

Type Specifications RemarksDeadbolt input: DC12V,

1A or lower

Voltage output,

Fail Safe/Secure

Electronic

Magnetic-Lock

input: DC12V,

1A or lower

Voltage output,

Fail Safe/Secure

Electric Strike input: DC12V,

1A or lower

Voltage output,

Fail Safe/Secure

Auto Door *Maximum Switching Voltage:

220V DC,250V AC.

*Maximum Switching Current:

2A DC,AC or lower

Contact output

Fail Safe Type: UNLOCKED, Open Type on EmergencyFail Secure Type: LOCKED, Close Type on Emergency

4.3 Connecting the external cables

You should connect the following external cables.

But you don't have to install the network cables if the customer

doesn't request them.

Door control cable

Network cable

Power cable

Wiegand signal cable

RS485 cable


11/20

- 12 -

4.3.1 Connecting the door control cable (Main board J2)

Specifications of the cable and material

Housing Receptacle Cable

5264-06 5263PBT UL Cable, 24~28AWG

Connection Note

Pay attention to terminal numbers when connecting the cable to

the connector.

Contact output is used when installing on the auto door. So makesure to set the terminal [JP1] as OPEN. The factory default of

the terminal [JP1] is JUMPER.

Some locking devices may not have door monitoring signals.


12/20

- 13 -

How to connect cables by types of locking devices

Deadbolt/Strike/Electronic Magnetic-Lock

PIN

NO.Feature Fail

Safe Type

Fail

Secure

Type

Door

Monitoring

Door

Open

1 GND GND GND COMOpen

button

2 Door Open buttonOpen

button

3 Door MonitoringMonitor

(12/24V)

4 CONTACT_BVCC(12/24

V)

5 COMMON (COM)

6 CONTACT_AVCC(12/24

V)

*The Relay Boad [JP1]=>Close


13/20

- 14 -

Auto DoorPIN

NO.Feature Normal

Open

Normal

Close

Door

Monitoring

Door

Open

1 GND COMOpen

button

2 Door Open buttonOpen

button

3 Door MonitoringMonitor

(12/24V)

4 CONTACT_B Contact

5 COMMON Contact Contact

6 CONTACT_A Contact

*The relay board [JP1]=>Open


14/20

- 15 -

4.3.2 Connecting the network cable (Network board J3)

Connect network lines as follows (pay attention to PIN numbers):

SchematicHousing Cable

PIN No Feature

1 TXP

2 TXN

3 RXPRJ45, 8PIN UTP

6 RXN

4.3.3 Connecting the power cable

Connect 12V adapter to Relay Board J4.

Connect 5V adapter ro Main Board J3

4.3.4 Wiegand output (Main board J5)

Check if the external device is pull up. If it is not, connect J16 and

J17.


15/20

- 16 -

4.3.5 RS-485 (Main board J1)

* If the device needs a termimal resistance, connect J18.

4.3.6 Wiegand input (Main board J9)

* Wiegand input cannot be used with RF module.


16/20

- 17 -


17/20

- 18 -


18/20

- 19 -

Fasten the terminal


19/20

- 20 -


20/20

- 21 -

5. Check After Installation

When you finish the installation of the entire system, check if it is

installed correctly before supplying power.

Check if locking device and other devices work normally as the

following order. For more information, please refer to

"NAC-2500 Terminal User Manual" and "Access Manager

User Manual ".

When power is supplied, the initial screen with NITGEN logo

will appear.

Press the menu button to choose System Option > Terminal

Mode and check if the terminal is in SO mode.

Choose User Manager from the menu and then register user

ID and fingerprint. (By default, user ID is set to 4 digits long.)

Test the devices (including locking device) attached to the

terminal by performing fingerprint authentication.

If there's no problem, delete the fingerprint you registered for

the test.

If you manage terminals via the network after installation,

proceed the following test:

Install the program on a server PC for manager registration

and initial settings.

Set the terminal mode to NL or NS from the terminal menu.

Set the network environment from the terminal menu.

Run Remote Manager to check the terminal connection and

then register it.

In the server PC, register a terminal user and check if the

authentication is performed normally.

If there's no problem, delete both server and terminal users.

Nitgen NAC 2500 PLUS Fingerprint Access Controller Terminal Installation Manual

Documents

Transcript of Nitgen NAC 2500 PLUS Fingerprint Access Controller Terminal Installation Manual