Newton Waterproofing Systems

8/3/2019 Newton Waterproofing Systems

1/42

NEWTON WATERPROOFING SYSTEMS

Product Catalogue

100 - Cementitious Products

200 - Deck And Roong300 - Waterproong of Concrete Structures

400 - External Waterproong

500 - Cavity Drain Waterproong

600 - Flooring Membranes

700 - Liquid Applied Floor Coatings

800 - Damp Proong

900 - Liquid Primers & Sealers

FlexProof Construction Joint Waterproong

Diathonite Insulating Plaster

Sump and Pump

Multi-Use

John Newton & Co. Ltd.

Issue Date: February 2012

Ln6 (L34)Cl/SfB

Protecting buildings, since 1848


2/42

PRODUCT CATALOGUE

SYSTEM 100 - CEMENTITIOUS PRODUCTS

Newton System 100 is a comprehensive portfolio

of cementitious products which have been

introduced into our structural waterproong range

to complement and complete our basement

waterproong designs in areas where the Newton

System 500 would not be suitable. Such details

include - lift shafts, at softs and externally to

retained slabs and ring beams.

Newton 101 F (CW 101), Page 4

Cementitious Flexible Waterproong Membrane

Newton 102 WaterPlug (CW 102), Page 5

Fast Setting Polymer Compound To Seal Leaks

Newton 103 SBR (CW 103), Page 5

Waterproof Additive

Newton 106 Lime Inhibitor (LC1), Page 5

Lime Inhibitor for Application to Concrete Surfaces

Newton 107 QuickFillet (CW 107), Page 6

Fast Setting Pre-Mix Mortar for Angle Fillets

SYSTEM 200 - DECK & ROOFING

A complete range of externally applied elastomeric

high performance liquid membranes and ancillaries

for balconies, terraces, at and inverted roofs,

podium decks, car parks and reservoirs. This new

portfolio of seamless and robust liquid membranes

gives speciers and specialist waterproong

contractors a quick and cost effective solution to

protect external areas from water ingress.

Newton RubberFlex System, Page 7

Podium Deck and Flat Roof Waterproong System

Newton 204 Thinner (RF 204), Page 8

Polyurethane Thinning & Cleaning Agent

Newton 205 ColorSeal (LM 205), Page 8

UV Colour Stable Polyurethane Coating

Newton 207 DeckDrain (M30), Page 9

Drainage Membrane for Decks and Flat Roofs

Newton 209 Root Barrier (M32), Page 9

Puncture Resistant Root Barrier Membrane

Newton 210 FlexProof-NV (FP4), Page 10

Waterproong of Podium Decks and Flat Roofs

Newton 220 Reservoir (M31), Page 10

Extensive Green Roof Drainage Membrane

SYSTEM 300 - WATERPROOFING OF

CONCRETE STRUCTURES

Newton System 300 is a range of products, some

unique to John Newton, used to waterproof con-

struction joints and movement joints of retained

concrete structures so that they become integrally

waterproof without the need of additional water-

proong products, dened within BS8102:2009 as

Type B waterproong.

Newton 301 AquaProof, Page 11

Metal Construction Joint Water Bar

Newton 302 InjectionHose, Page 11

Maintainable Injection Water Bar System

Newton 303 PolyProof, Page 12

High Grade Hydrophilic Water Bar

Newton 304 PolyProof Inject, Page 12

High Grade Hydrophilic Water Bar

Newton 305 ActiveJoint, Page 12

Physical Movement Joint Water Bar

Newton 306 SwellMastic, Page 13

Swelling Adhesive

Newton 307 PipeSeal, Page 13

Pipe Collar

Newton 308 Stopaq (SX 108), Page 13

Unique Hydrophilic Polymer Sealant

SYSTEM 400 - EXTERNAL WATERPROOFING

System 400 is a range of products for the

waterproong of the outside of earth retainedstructures. Products include sheet membranes for

the complete envelopment of the raft and walls,

exible liquid products for the waterproong of

retained walls and composite drainage membranes

for preventing the build up of ground water to the

walls or below the raft. Newton System 400 products

can provide Type A and Type B waterproong to

Grades 2 & 3 as dened within BS8102:2009

Newton 401 FlexProof-X1, Page 14

Flexible Membrane for Retaining Walls

Newton 402 Aquabit, Page 15

Flexible Membrane for Retaining Walls

Newton 403 HydroBond, Page 15

Hydrophilic and Bonding Membrane for Raft and

Wall Waterproong

Newton 410 Geodrain, Page 16

Externally Applied Drainage Membrane

Note: Please check individual product sheets for advice on appropriate xings and ancillary products. Contact our Technical

Department for further information on 020 7237 1217. Copies of our BBA Certicates, Brochures and Data Sheets can be

downloaded from www.newton-membranes.co.uk. Products and their specications can be changed or modied without

prior notice. All copy, diagrams, images and Newton trade names/logos and designs used in this catalogue remain theintellectual property of John Newton and Company Ltd. and may not be reproduced without the written permission of the

Directors of John Newton and Company Ltd. Any party who exploits this property may be subject to prosecution.

John Newton & Co. Ltd. 12 Verney Road, London SE16 3DH - 020 7237 1217

www.newton-membranes.co.uk - [email protected]


3/42

PRODUCT CATALOGUE

SYSTEM 500 - CAVITY DRAIN WATERPROOFING

The professionals waterproong system of

choice, Newton System 500 is an internally

applied waterproong system based upon our range

of cavity drain membranes, drainage conduits and

sophisticated pumping and control systems. Unlike

conventional tanking, Newton System 500 is not

attempting the almost impossible and trying to

hold water back, but places designed maintainable

depressurisation voids at known weaknesses in

the structure so that ingressing water is simply

captured and diverted out of the property.

Wall Membranes

Newton 503 (M5), Page 17

Newton 503 Mesh (M11 & M12), Page 17

Newton 508 (M1 & M2), Page 18

Newton 508 Mesh (M3), Page 18

Newton 520 (M4 & M13), Page 18

Drainage System

Newton Basedrain (D1), Page 18

SYSTEM 600 - FLOORING MEMBRANES

Newton System 600 is a range of HDPE and

HDPP ooring membranes offering a complete

damp proof solution for both commercial and

domestic ooring applications. As well as

providing protection from dampness within the

oor, our membranes de-couple the oor nish

from the substrate preventing damage due tosubstrate movement and cracking. Newton damp

proof membranes can be installed over existing

and green concrete. In addition, our ooring

membranes are a popular solution for dealing with

inherent hydrocarbons or ground gas problems.

Newton ooring membranes can accommodate a

variety of nishes including timber oors, screeds

and direct tiles.

Flooring Membranes

Newton 601 Slimline (M6), Page 19

Newton 603 (M23), Page 19

Newton 603 Mesh (M24 & M25), Page 20

SYSTEM 700 - LIQUID APPLIED FLOOR COATINGS

System 700 is a range of liquid applied protective

and decorative internal ooring products. These

products are fast curing and available in a

variety of colours, and are typically used for the

refurbishment and protection of commercial and

domestic oors.

Newton 701 HB (LM 701), Page 21

High Build Epoxy Floor Coating

Newton 702 EcoSeal (LM 702), Page 21

Highly Resistant Polyurethane Floor Coating

SYSTEM 800 - DAMP PROOFING

Newton System 800 is a range of BBA approved

damp proof membranes and ancillaries which are

quick and clean to install and offer a permanent

solution for damp proong walls. The meshed

membranes provide a rm key and impermeable

barrier on any damp or deteriorating surface ready

for plaster, render or dot & dab plasterboard. The

un-meshed Newton 803 is used where insulation

requirements dictate the use of a timber or steel

frame ready for plasterboard. Quick, clean and

proven to work, Newton damp proof membranes

offer a permanent and cost effective damp

proong solution.

Damp Proong Membranes

Newton 805 Newlath (M9 & M10), Page 22

Newton 803 (M19 & M20), Page 23

Newton 803 Newtonite (M16, M21, M22), Page 23Newton 801 FlexProof-X1 Wet Room Waterproong,

Page 23

Damp Proong Ancillaries

Newton 800 Mesh Plug (A16), Page 24

Newton MultiPlug (A1), Page 24

Newton 800 Cob Plug (A17), Page 24

Newton 800 Newtonite Plugs (A20), Page 24

Newton 800 Mastic (A18), Page 25

Newton Mesh Tape (A25), Page 25

Newton Overtape (A8), Page 25

Newton 800 Prole (A19), Page 25

SYSTEM 900 - LIQUID PRIMERS & SEALERS

Newtons high performance range of liquid applied

products are used in conjunction with System 200

and 700 liquid membranes. They act as priming

agents for a variety of substrates prior to the

application of our specialist waterproong and

ooring membranes.

Newton 901 Humidity Primer (PS 901), Page 26

Epoxy Primer Suitable for High Humidity SubstrateNewton 902 (PS 902), Page 26

Liquid Applied Radon, Gas & Vapour Barrier

Newton 903 PU Primer (PS 903), Page 27

Epoxy Primer for Nonporous Substrate

Newton 904 HP Accelerant (PS 904), Page 27

Humidity Primer Accelerant

Newton 906 Mould Stop (PS 906), Page 27

Mould Steriliser & Killer




4/42

PRODUCT CATALOGUE

NEWTON FLEXPROOF - CONSTRUCTIONJOINT WATERPROOFING

Newton FlexProof-X1 forms an elastomeric polymer

membrane that is rainproof in minutes and

capable of handling severe building movements

and deformations. FlexProof-X1 is quite unique

with amazing characteristics allowing it to be used

without a primer, without mixing and in weather

conditions that preclude the use of alternatives.

Newton FlexProof-X1 (FP1), Page 28

Construction Joint Waterproong

NEWTON DIATHONITE - INSULATING PLASTER

Newton Diathonite is a premixed plaster, bre-

reinforced with cork (granular 0-3 mm), clay

powders and NHL 3.5 natural hydraulic lime.

The resulting natural compound produces a plaster

with unrivalled thermal and acoustic properties that

is both hard wearing and exible which is ideal for

both internal and external applications. .

Newton Diathonite, Page 29

Eco Thermal Plaster with Insulation and Acoustic

Properties

SUMP AND PUMP

Newtons have an extensive range of submersible

pumps and pumping ancillaries. We supply the

highest quality pumps available in each class,

for the control of clean ground water, grey water,

efuent or sewage.

Clean/Ground Water Pumps

Newton NP150 (P1), Page 30

Newton CP250 (P31), Page 30


Newton NP400 (P2 & P3), Page 31

Newton NP400PP (P13), Page 31

Newton NP400LLPS (SP1), Page 31


Newton NP750 (P5 & P6), Page 32

Efuent Pumps (Not Sewage)

Newton NP400W (P4), Page 32

Sewage Pumps

Newton SP750 Ranger (P9), Page 33

Newton Flygt DXG (Grinder) (P14 & P16) Page 33

Sewage Lifting Station

Trojan Sewage Pumping System (TR1-TR12), Page 33

Clean/Ground/Efuent Pumping Systems

Titan-Pro White (TPW), Page 34

Titan-Pro Green (TPG), Page 34

Newton Titan-2 (T1-T10), Page 34

Pumping Ancillary Products

Newton Control Panel Pro (CP2), Page 35

Newton High Water Level Alarm (PA50), Page 35

Newton Dialer (PA5, PA6, PA7), Page 35

Newton 1200w Power Converter (C1 & C3), Page 36

Newton 3000w Power Converter (C2 & C4), Page 36

Newtons can also provide a wide range of specialist

submersible pumps and sump chambers which

can be tailor made for site-specic conditions. For

further information call our technical department

on 020 7237 1217

MULTI-USEThe Multi-Use section is home to products that

are used within more than one of our systems.

WaterSeal Tape, for example, can be used with

System 300, System 400, System 500, System 600

and System 800.

Newton Mesh Tape (A25), Page 37

Newton Overtape (A7, A8, A9), Page 37

Newton WaterSeal Rope (A6 & A6W), Page 37

Newton WaterSeal Tape (A5 & A5W), Page 38

Newton MultiPlug (A1), Page 38

Newton NuSeal Plugs (A2 & A3), Page 38




5/42

J o h n N e w t o n Lt d I s s u e 0 1 M a y 0 8 w w w . n e w t o n - m e m b r a n e s . c o . u k i n f o @ n e w t o n - m e m b r a n e s . c o. u k

NEWTON SYSTEM 100Cementitious Products

SYSTEM OVERVIEW

NEWTON SYSTEM 100 - CEMENTITIOUS PRODUCTSSystem Overview

Newton System 100 is a comprehensive portfolio ofType A

(BS8102:2009) cementitious waterproong products for the sealing of

leaks and the waterproong of lift shafts, at softs, walls and slabs.

System 100 products can be used on their own, or in conjunction with

System 200, System 300, System 400 and System 500 waterproong

products, and with System 700 (Liquid Flooring Membrane) and System

800 (damp-proong) products also.

NEWTON 101F (CW 101)Cementitious Flexible Waterproong Membrane

Newton 101F is a two-component acrylic modied cementitious coating.

It is the ideal product to waterproof and re-surface concrete and masonry.

101F is a hard wearing, seamless waterproong solution which is very

user friendly with simple on-site mixing methods.

Newton 101F is applied in two coats 1mm each to provide a total

thickness of 2mm. Each 1mm coat requires a coverage rate of

1.8kg per m to give a total coverage rate of 3.6kg per m. Newton 101F

is supplied in two components of 1 x 25kg tub of powder and 10kg of

liquid additive (35kg pack) which will cover 9m - 10m

Typical Applications:

Waterproof lining for lift pits, swimming pools etc

Bathroom and wet areas

Waterproof coating for roofs

Internal application to at concrete softs in conjunction with

Newton System 500

Slurry application to form waterproof bunds

Lining existing concrete sump chambers

Protection of steels against carbonation and chloride attacks

Page 4




6/42



SYSTEM OVERVIEW

NEWTON 102 WATERPLUG (CW 102)Fast Setting Polymer Compound To Seal Leaks

Newton 102 WaterPlug is a fast setting, polymer compound that instantly

stops running water or seepage through masonry or concrete substrates.

It becomes harder and more resistant when subjected to constant water

pressure. Newton 102 WaterPlug is a non-shrink material that expands

slightly and sets in approximate 2 minutes. Available in 5kg, 10kg or

25kg tubs.


Leak sealing prior to tanking with Newton 101F

Sealing of leaks at wall/oor junctions

Sealing of leaking mortar joints

Leak sealing of cracks in masonry or concrete

Repair of construction faults such as honeycombing

Anchoring of bolts or posts

Controlling water ingress during sump installations

NEWTON 103 SBR (CW 103)Waterproo Additive

Newton 103 SBR is a high quality liquid, water-based high solids

styrene butadiene polymer latex with high bonding and waterproong

characteristics. It is stable under wet alkaline conditions forming a

reinforcing polymer matrix within cementitious mixes. Available in 5kg,10kg and 25kg


Surface waterproong Lift shafts

Waterproof screeds Wall/oor junction llets

NEWTON 106 LIME INHIBITOR (LC1)Lime Inhibitor For Application To Concrete Suraces

Newton 106 Lime Inhibitor is applied to concrete surfaces prior to the

installation of a Newton System 500 cavity drain membrane waterproongsystem to prevent the leaching of free lime from the concrete. Primarily

designed to be used to new concrete structures, Newton Lime Inhibitor

should also be used to treat the following areas: newly formed concrete

walls, kickers and underpins, treatment to cut recesses prior to Basedrain

installation and as a concrete additive to newly formed sump chambers.

Supplied in 1kg units - Newton 106 is a concentrated mix to be added

1 part Newton 106 Lime Inhibitor to 9 parts clean water. Newton 106

should be applied in this 10 litre mix through a course sprayer and will

cover a maximum of 100 sq m

Product Features:

Solvent and caustic free Easy to use and handle

Non-hazardous (on dilution) Long term durability

Compatible with alkaline substrates



Page 5


7/42



SYSTEM OVERVIEW

NEWTON 107 QUICKFILLET (CW 107)Fast Setting Pre-Mix Mortar For Angle Fillets

Newton 107 QuickFillet is a fast setting and fast curing mortar with a

rapid strength gain used to quickly form 45 angled llets at junctions

between walls and oors or softs. Newton 107 QuickFillet should be

used to form llets for use with Newton 101F cementitious slurry and

can be used to reinforce internal corners ready for Newton liquid applied

membranes such as 201 RubberFlex, 205 ColorSeal or 702 EcoSeal.

Newton 107 Quick Fillet can also be used to repair substrate prior to the

use of Newton System 900 primers.

Newton 107 QuickFillet is supplied in 25kg tubs and when correctly mixedwith 3.6 litres of clean water should cover approx 30 linear metres applied

in a 25mm x 25mm llet


Creation of angle llets

Surface repairs to substrate prior to application of Newton System

900 oor primers



Page 6


8/42


NEWTON SYSTEM 200Deck & Roofing

SYSTEM OVERVIEW

NEWTON SYSTEM 200 - DECK AND ROOFINGSystem Overview

Newton System 200 is a complete range of externally applied liquid

elastomeric membranes for the structural waterproong of podium decks,

balconies and terraces, at and inverted roofs, car parks, swimming

pools, green or turf roofs and reservoirs. This new portfolio of seamless

and robust liquid membranes gives speciers and specialist waterproong

contractors a quick and cost effective solution to protect external areas

from water ingress.

NEWTON RUBBERFLEX SYSTEMPodium Deck and Flat Roo Waterproong System

Newton RubberFlex is a BBA Certied single part liquid waterproong

material, which forms an elastomeric polyurethane membrane, resisting

UV rays and capable of handling severe building movements and

deformations. Newton RubberFlex is guaranteed against deterioration

for 25 years and is supported by BBA Certication Certicate Number

11/4840. Newton RubberFlex can be specied as a UV stable

waterproong membrane with high resistance to impact and abrasion

or can be the primary waterproong barrier when used with Newton

207 DeckDrain drainage membrane to create a complete drained

waterproong solution.

Newton RubberFlex is available in three variants, the choice of whichwould be dependent on the required speed of application between coats

as well as on the temperature and humidity at the time of installation and

the type and height of up-stand to be installed.

Newton 201 RubberFlex

Self levelling with standard cure times used for horizontal surfaces and

up-stands of up to 250mm with reinforcement.

Newton 202 RubberFlex-QC

Quick Curing derivative with fast cure times used for horizontal surfaces

and up-stands of up to 250mm with reinforcement.

Newton 203 RubberFlex-VThixotropic variant for larger vertical areas.

Newton RubberFlex can be applied either as a reinforced or a non-

reinforced system depending on substrate type or substrate quality. See

product datasheet for more details.

Application rates: 25kg is sufcient to cover 12.5m2 of surface with a two

coat treatment of 2kgs per m2 providing an overall membrane thickness

of 1.9mm (refer to data sheets for suggested drying times between coats)

Specialist application equipment such as spiked rollers are available

on request.

201 RubberFlex and 202 RubberFlex QC are available in 10kg and 25kg

tins. 203 RubberFlex-V is available in 10kg tins.



Page 7


9/42



SYSTEM OVERVIEW

NEWTON 204 THINNER (RF 204)Polyurethane Thinning & Cleaning Agent

Newton 204 Thinner is a slow acting blended solvent for use with Newton

RubberFlex and Newton 205 ColorSeal. Newton 204 Thinner is used to

dilute the polyurethane membrane and is especially useful when Newton

RubberFlex is applied by airless spray.

Newton 204 Thinner is also used as a cleaning medium for tools and

equipment used during the application of the membrane and it can

also be used as a barrier against humidity when having to store product

already opened. Newton 204 Thinner is supplied in 4kg, 9kg and 20kg

containers.

Newton 204 Thinner is also used for cleaning tools used with Newton

Flexproof products.


Cleaning of tools and equipment

Increasing viscosity of membranes for application by airless spraying

Sealing of product against moisture in opened containers

NEWTON 205 COLORSEAL (LM 205)UV Colour Stable Polyurethane Coating

Newton 205 ColorSeal is a UV stable, single component, protective

polyurethane resin top-coat. 205 ColorSeal provides a transparent hard

wearing coating, or it can be coloured with the addition of pigmented quartz

sand to provide a textured, slip resistant, UV colour stable nish. Its primary

use is as a UV stable and hard wearing protection coat above the Newton

RubberFlex podium deck and at roof waterproong system.

The exceptional strength and durability means that Newton 205 ColorSeal

can also be used as a stand-alone ooring product. It cures to a gloss

nish. For pedestrian walkways it is recommended that a coloured quartz

sand is applied to the still tacky rst coat of 205 ColorSeal to give a non-

slip surface. Newton 205 ColorSeal is supplied in 4kg, 9kg and 20kg

containers.

Coverage: a 4kg pack is sufcient to cover a prepared surface area of 13m2

with the recommended covering of 0.3kg/m2 providing an overall thickness

of 250-400 microns. With a two coat application which includes the quartz

sand anti-slip layer, coverage will be 6m2 with the recommended two

coat treatment


Heavy trafc areas

Industrial factories, depots and warehouses

UV colour stable and non-slip nish to other oor coatings



Page 8


10/42



SYSTEM OVERVIEW

NEWTON 207 DECKDRAIN (M30)Drainage Membrane or Decks and Flat Roos

Newton 207 DeckDrain is a double cuspated, deck and at roof drainage

membrane, that incorporates a non-woven geotextile lter layer, bonded to

a water impermeable HDPE (High Density Polyethylene) core. The double

cuspated design provides two layers of drainage; allowing for primary

drainage through the geotextile lter, as well as secondary drainage between

the underside of 207 DeckDrain and the primary waterproong layer.

The lower drainage layer eliminates the risk of trapped water, a problem

associated with conventional single cuspated deck drainage membranes.

Newton 207 DeckDrain is supplied in 1.1m wide x 25m long rolls and is

simply laid above the waterproong membrane with the geotextile eece

uppermost.


As the drainage layer above a deck, balcony or at roof waterproong

membrane such as Newton 201 RubberFlex, particularly where:

1. Block paviours or ooring slabs are bedded on sand as the surface nish.

2. Soil lled planters are included to the deck or at roof.

Also suitable for use as a vertical drainage layer when used as part of

a professionally designed and installed externally applied basement

waterproong system.

NEWTON 209 ROOT BARRIER (M32)Puncture Resistant Root Barrier Membrane

Newton 209 RootBarrier is designed to eliminate root penetration. It

consists of an impermeable High Density Polyethylene (HDPE) membrane,

providing robust root-proof protection to the primary waterproong

membrane to green roofs or planters where intrusive root systems are

present.

The membrane has high tensile strength and puncture resistance

and provides an efcient, reliable and cost effective barrier to provide

protection against Japanese Knotweed and other aggressive root systems.


As a root barrier to protect the waterproong membrane from root damage

within intrusive green roof systems or planters.

Newton 209 RootBarrier is supplied in 1.2m wide x 50m long rolls and is

placed above the waterproong membrane and the Newton 207 DeckDrain

(if included in the design). Joints are overlapped by at least 150mm and

sealed with two lines of Newton Waterseal Tape.



Page 9


11/42



SYSTEM OVERVIEW

NEWTON 210 FLEXPROOF-NV (FP4)Waterproong o Podium Decks and Flat Roos

Newton 210 FlexProof-NV is a highly advanced single component liquid

waterproong material, which forms an elastomeric polymer membrane

capable of handling severe building movements and deformations.

Movement joints to Decks and Flat Roofs can also be waterproofed with

Newton 201 FlexProof-NV whether the main waterproong membrane is

FlexProof-NV or Newton RubberFlex.

Newton 210 FlexProof-NV has characteristics that allow it to be used

without a primer, without mixing and in weather conditions that preclude

the use of alternatives. With a tight project timescale, 210 FlexProof-NV

can be relied upon to ensure the project is completed on time.

Newton 210 FlexProof-NV can be used as the primary waterproong

membrane below a number of hard nishes and drainage options and

when partnered with Newton 207 DeckDrain drainage membrane, creates

a complete drained waterproong solution to your deck, terrace or at roof.

Newton 210 FlexProof-NV is supplied in 7.5kg and 26kg containers and is

applied to the deck or roof with a squeegee or trowel and is simply poured

into movement joints.


Waterproong of podium decks, balconies, terraces and at roofs.

As the primary waterproong membrane below a green roof.

As the waterproong membrane within a warm roof specication.

Waterproong of planters

NEWTON 220 RESERVOIR (M31)Extensive Green Roo Drainage Membrane

Newton 220 Reservoir is a unique drainage and water retention

membrane for use where a water reservoir is required for extensive green

roofs of sedum, herbaceous plants, mosses or grass above decks and

roofs.

Unlike other products of this type, Newton 220 Reservoir has a bonded

geotextile that prevents intrusion of the soil into the water holding cupsduring back-ll and compression. This results in a permanently larger

volume reservoir than any other 20mm deep green roof membrane.

When the water holding cups are full, the large drainage holes within the

HDPE core allow water to easily pass through to the drainage layer below

to prevent saturation and water logging of the green roof above.


As a water holding and drainage layer above a deck, at roof or pitched

roof where shallow planting is used to create an extensive green roof.

Newton 220 Reservoir is supplied in 0.92m wide x 50m long rolls and is simply

laid above the waterproong membrane with the geotextile eece uppermost.



Page 10


12/42


NEWTON SYSTEM 300Waterproofing of Concrete Structures

SYSTEM OVERVIEW

NEWTON SYSTEM 300

WATERPROOFING OF CONCRETE STRUCTURESSystem Overview

Newton System 300 is a range of products, some unique to John Newton,

used to waterproof construction joints and movement joints of retained

concrete structures so that they become integrally waterproof without the

need of additional waterproong products, dened within BS8102:2009

as Type B waterproofng.

Waterproong can be further enhanced by the addition ofType A (Newton

System 100 or System 400) or Type C(Newton System 500) waterproong

systems to provide a combined waterproong approach, recommended

by BS8102:2009 when absolute waterproong security is required.

The podium deck of a retained concrete structure would also require

waterproong with one of our System 200 products.

NEWTON 301 AQUAPROOFMetal Construction Joint Water Bar

Newton 301 AquaProof is a coated metal water bar system used for the

sealing of construction joints within retained concrete structures.

Newton 301 AquaProof features an adhesive, reactive

polymer coating on one of its sides. The coating creates a permanent

watertight seal with the surrounding concrete to create a water bar that

works immediately.

Newton 301 AquaProof is supplied in 6m rolls and is tted to the

reinforcing steel with Omega Clips prior to the placing of the concrete.


The waterproong of construction joints to poured concrete elements

of earth retained structures.

NEWTON 302 INJECTIONHOSE

Maintainable Injection Water Bar System

Newton 302 InjectionHose is a high performance injectable water bar

system used for the sealing of construction joints within retained concrete

structures.

The system offers many benets over conventional water bars,

especially its ability to grout poorly compacted concrete and by offering a

maintainable solution that allows for resealing of the construction joint,

post construction.

Newton 302 InjectionHose is supplied in reels of 120m and is applied to

an already formed concrete element prior to formation of the joint.


Post construction grouting and leak sealing of construction joints to

poured concrete earth retained structures.



Page 11


13/42



SYSTEM OVERVIEW

NEWTON 303 POLYPROOFHigh Grade Hydrophilic Water Bar

Newton 303 PolyProof is a very high grade hydrophilic water bar which

seals gaps in construction joints by swelling up to 400% its original size.

The water bar is adhered to the face of the rst pour of the joint with

either Newton 306 SwellMastic or Newton 309 Contact Adhesive. Can

also be used as the water bar in settlement or compression joints.

303 PolyProof is available in the following sizes:

Depth Width Length

303 PolyProof-2 2mm 20mm 25m




Waterproong of static construction joints, settlement joints and

compression joints to concrete earth retained structures.

NEWTON 304 POLYPROOF INJECTHigh Grade Hydrophilic Water Bar

Unique construction joint water bar that combines the high performance

swelling capabilities of Newton 303 PolyProof and the post construction

injection of grouts and resins provided by Newton 302 InjectionHose.

Newton 304 PolyProof Inject is supplied in coils of 60m and is

mechanically xed to the construction joint with special clips.


Waterproong using hydrophilic swelling and post construction

grouting and leak sealing of construction joints to poured concrete

earth retained structures.

NEWTON 305 ACTIVEJOINTPhysical Movement Joint Water Bar

MDPE physical water bar for the waterproong of movement joints. Thewater bar has a unique V shape with a number of barbs so that water

pressure expands the joint, creating more grip to the concrete joint as the

pressure increases.

Newton 305 ActiveJoint is supplied in eight widths to waterproof

movement joints from between 25mm to 100mm. The product is simply

hammered into a movement joint that has been lubricated with Newton

306 SwellMastic, which is hydrophilic and will swell in contact with water

to further waterproof the joint.


Waterproong of movement joints.



Page 12


14/42



SYSTEM OVERVIEW

NEWTON 306 SWELLMASTICSwelling Adhesive

Newton 306 SwellMastic is a high performance mastic used to adhere

Newton 303 PolyProof and Newton 305 ActiveJoint to the concrete joint.

Can also be used to seal around protrusions such as pipes and conduits

and should be used to reinforce Newton 307 PipeSeal being tted to

pipes passing through the structure.

Newton 306 SwellMastic is supplied in cartridges of 290ml and foil

sausages of 600ml and is applied in a bead.


Sealing around protrusions through the structure such as service

pipes and as an adhesive for Newton 303 PolyProof, 304 PolyProofInject and 305 ActiveJoint.

NEWTON 307 PIPE SEALPipe Collar

Newton 307 PipeSeal is a preformed MDPE seal that creates a physical,

anged joint around pipes passing through the structure. Newton 306

SwellMastic should be used to reinforce the joint.

Newton 307 PipeSeal is available for sealing pipes of diameters of

110mm and 160mm and they are simply slipped over the pipe using

neutral soap as a lubricant.


Sealing around pipes protruding through the structure.

NEWTON 308 STOPAQ (SX 308)Unique Hydrophilic Polymer Sealant

Newton 308 Stopaq is a unique swelling sealant compound system

which provides a waterproong solution for the notoriously difcult to seal

service pipe penetrations through retaining walls.

Newton 308 Stopaq is supplied in 0.53kg tubes and is applied with a

specialist applicator gun. The product cartridge needs to be warmed prior

to installation by submersing in warm water.


Sealing around cables, conduits and other difcult to seal protrusions

through the structure whether in sleeve pipes or directly through the

concrete.



Page 13


15/42


NEWTON SYSTEM 400External Waterproofing

SYSTEM OVERVIEW

NEWTON SYSTEM 400 - EXTERNAL WATERPROOFINGSystem Overview

System 400 is a range of products for the waterproong of the outside

of earth retained structures. Products include sheet membranes for the

complete envelopment of the raft and walls, exible liquid products for the

waterproong of retained walls and composite drainage membranes for

preventing the build up of ground water to the walls or below the raft.

Newton System 400 products can provide Type A and Type B

waterproong to Grades 2 & 3 as dened within BS8102:2009 Code of

Practice for the Protection of Below Ground Structures Against Water from

the Ground.



Page 14

NEWTON 401 FLEXPROOF-X1Flexible Membrane or Retaining Walls

Newton 401 FlexProof-X1 is a highly advanced single component liquid


that is rainproof in minutes and capable of handling severe building

movements and deformations.

401 FlexProof-X1 has characteristics that allow it to be used without a

primer, without mixing and in weather conditions that preclude the use of

alternatives.Newton 401 FlexProof-X1 comes in containers of 15kg & 26kg which is

applied by trowel in one coat of 3kg/m2.

Suitable Substrate:

Concrete or masonry retained walls.

Key Benefts

No mixing required simply open the packaging and use.

Can be used in sub-zero temperatures and on slightly damp

substrate.

No primer required saving on primer and labour costs

Single coat application.

100% waterproof, but allows vapour diffusion.

Very exible Resistant to movement and ssures in substrates.

Excellent adhesion to suitable substrates.

Resistant to temperature variations maintaining its characteristics

between -40C & 90C.

Excellent resistance to the high alkalinity of concrete


16/42



SYSTEM OVERVIEW



Page 15

NEWTON 402 AQUABITFlexible Membrane or Retaining Walls

Newton 402 Aquabit is a single component water based waterproong

bituminous mortar that includes polystyrene micro-spheres that allow it

to be applied obtaining a level of thickness up to 3mm, modied to make

the product extremely workable and able with just one coat to ll surface

irregularities, typical on concrete foundation walls. The material is also

characterised by a high elasticity, crack bridging ability and a good salt

resistance. It can be applied both on old and new walls.

Newton 402 Aquabit comes in containers of 25 litres which is applied by

trowel in one coat of 2.2 litres per m2 to give an average thickness

of 2.5mm.


Waterproong of retained walls

NEWTON 403 HYDROBONDHydrophilic and Bonding Membrane or Rat and Wall Waterproong

Newton 403 HydroBond is a very high performance composite sheet

membrane that features a locking eece to one side and a polymer

hydrophilic coating to the other side.

When placed below the new raft or against the wall shuttering, the

poured concrete engages into the locking eece so that the membrane is

completely locked in and monolithic to the concrete thus ensuring that if

a leak did occur it cannot track to the construction joints. The hydrophilic

coating seals small holes that may be accidentally formed during xing of

the reinforcing steel or the pouring or compaction of the concrete.

Newton 403 HydroBond is supplied in rolls of 2m x 30m and can be laid

to the blinding and shuttering of a raft construction or adhered to already

formed retaining walls.


Waterproong of retained walls

Waterproong of decks


17/42



SYSTEM OVERVIEW



Page 16

NEWTON 410 GEODRAIN (M18)Externally Applied Drainage Membrane

Newton 410 Geodrain is a component drainage sheet consisting of a

non-woven geotextile lter layer thermally welded to a water impermeable

HDPE drainage membrane. Newton 410 Geodrain provides outstanding

drainage and protection to the outside face of basement walls, preventing

the build-up of water pressure and protecting the structure from

aggressive water, chemicals and toxins.

Newton 410 Geodrain comes in rolls which are 2m x 12.5m with a surface

coverage of 25m2 (in-line studs 10mm in depth)


As the drainage layer of an externally applied waterproong systemwhen used in conjunction with sheet applied or liquid applied external

tanking membrane to BS8102:2009

Protection of the structure from aggressive chemicals in the ground water

To prevent the build up of ground water to retaining walls


18/42


NEWTON SYSTEM 500Cavity Drain Waterproofing

SYSTEM OVERVIEW

System Overview

The professionals waterproong system of choice, Newton System 500

is an internally applied waterproong system based upon our range of

cavity drain membranes, drainage conduits and sophisticated pumping

and control systems.

Unlike conventional tanking, Newton System 500 is not attempting the

almost impossible and trying to hold water back, but places designed

maintainable depressurisation voids at known weaknesses in the

structure so that ingressing water is simply captured and diverted out

of the property. Newton recommends that our structural waterproong

systems are installed by one of our Nationwide Network of Newton

Specialist Basement Contractors who have been trained by Newtonand can offer full professional indemnity on design and insured backed

guarantee on the installation.

NEWTON 503 (M5)3mm Cavity Drain Membrane or Basement Walls, Floors & Vaulted Softs

Newton 503 is a BBA approved cavity drain waterproong membrane

suitable for use internally to retaining walls, vaulted softs and oors.

Newton 503 is a exible HDPE membrane which at 0.5mm in thickness

provides a low prole drainage solution within the Newton Cavity Drain

membrane range.

Newton 503 (M5) is available in rolls 2m x 20m - 40m2

NEWTON 503 MESH (M11 & M12)3mm Cavity Drain Membrane or Basement Walls, Floors & Vaulted Softs

Newton 503 Mesh is a BBA certied meshed membrane suitable for use

as a waterproong membrane when used below the ground as part of

Newton System 500.

With its 3mm stud, Newton 503 Mesh is just 3.5mm in overall thickness,

and is the preferred meshed membrane where space is at a premium.

Its meshed surface provides an excellent key for lime mortars, renders,

plasters or dabbed plasterboard. When using Newton 503 Mesh, it is

essential to use Newton MultiPlug or Newton NuSeal with WaterSeal Rope

as a means of achieving a waterproof seal.

Newton 503 Mesh is available in roll sizes 1m x 20m -

20m2 (M12) and 2m x 20m - 40m2 (M11)



Page 17

NEWTON SYSTEM 500 - CAVITY DRAIN WATERPROOFING


19/42


NEWTON SYSTEM 500Cavity Drain Waterproofing

SYSTEM OVERVIEW

NEWTON 508 (M1 & M2)8mm Cavity Drain Membrane or Basement Walls, Floors & Vaulted Softs

Newton 508 is our high quality BBA approved cavity drain waterproong

membrane suitable for use internally below the ground to retaining walls,

vaulted softs and oors. Newton 508 is our agship membrane and one

of the most specied cavity drain membranes in the UK. The 0.7mm thick

HDPE product allows for large industrial loads to be applied and the in line

studs allow for quick installation with minimal surface preparation.

Newton 508 is available in roll sizes 2.4m x 20m - 48m2

(M1) and 2m x 20m - 40m2 (M2)

NEWTON 508 MESH (M3)8mm Meshed Cavity Drain Membrane or Basement Walls,

Floors & Vaulted Softs

Newton 508 Mesh is a BBA approved meshed cavity drain waterproong

membrane, suitable for use internally below the ground to retaining walls

and vaulted softs. Newton 508 Mesh is typically used where space

prevents the use of a dry-lining frame or block wall as the wall nish

or where a direct rendered or plastered nish is preferred. The ability

to apply direct nishes to the product makes it ideal for convoluted or

conned basement areas where space is at a premium or where the

original contours (features) of the property need to be retained.

Newton 508 Mesh (M3) is available in rolls 2m x 20m -40m2

NEWTON 520 (M4 & M13)20mm Cavity Drain Membrane or Basement Floors

Newton 520 is a BBA approved cavity drain membrane suitable for use

above basement oor areas. The 20mm studded membrane allows for

a massive ow rate to pass underneath the membrane and is specied

where oor areas are of questionable quality or where it is anticipated

that there may be a risk of severe water penetration.

Newton 520 is available in roll sizes 2m x 20m - 40m2

(M4) or 2m x 10m - 20m2 (M13)

NEWTON BASEDRAIN (D1)Drainage System

Newton Basedrain comprises a range of products that receive water

ingressing at weaknesses within the structure and then discharge the

collected water to a Newton Sump System or safe drainage (drainage that

is below the level of the basement oor that cannot back-up or block).

Basedrain is supplied in packs of 12 linear metres (6 x 2m) lengths.

Internal and external corners, T pieces, drainage connectors and access/

jetting ports should be utilised with Basedrain. Contact us for more details.



Page 18


20/42


NEWTON SYSTEM 600Flooring Membranes

SYSTEM OVERVIEW

NEWTON SYSTEM 600 - FLOORING MEMBRANESSystem Overview

Newton System 600 is a range of HDPE and HDPP ooring membranes

offering a complete damp proof solution for both commercial and

domestic ooring applications. As well as providing protection from

dampness within the oor, our membranes de-couple the oor nish

from the substrate preventing damage due to substrate movement and

cracking. Newton damp proof membranes can be installed over existing

and green concrete.

In addition our ooring membranes are a popular solution for dealing

with inherent hydrocarbons or ground gas problems. Newton ooring

membranes can accommodate a variety of nishes including timber

oors, screeds and direct tiles.

NEWTON 601 SLIMLINE (M6)Flat Loose Laid High Grade Flooring Membrane

Newton 601 Slimline is a high-grade ooring membrane used primarily for

isolating moisture sensitive ooring from dampness in the oor slab, but

can also be used as the oor membrane as part of Newton System 500

when the survey has ascertained that no risk of water entering through

the body of the slab exists.

Newton 601 Slimline allows for the installation of sensitive ooring to

be laid above green still curing concrete as soon as the concrete iswalkable, usually two days, signicantly reducing project times. With a

loading capability of over 1000kN/m2, Newton 601 Slimline is able to

resist very high compressive loading and is suitable for use as a high

load DPC within structural block walls, especially when used to connect

the wall and oor membranes within Newton System 500. Newton 601

Slimline is made from HDPP and is the thinnest prole membrane within

the Newton oor membrane portfolio.

Newton 601 is available in rolls 2.07m x 20m - 40m2 (M6)

NEWTON 603 (M23)

3mm Loose Laid Flooring Membrane

Newton 603 is suitable for use above new and existing oors. The 3mm

studs allow for pressure equalisation of dampness within the oor below

allowing for dissipation at room perimeter and subsequent drying of the

oor. The studs also give slight compression to footfall making the oor

very responsive and comfortable and ideal as the oor membrane for

performance sports oors. Newton 603 uncouples the oor nish from

the substrate so that movement is not transferred to the oor nish

above. The membrane also bridges small cracks allowing for quick oor

installation above less than ideal substrate.

Newton 603 is available in rolls 2m x 20m - 40m2 (M23)



Page 19


21/42


NEWTON SYSTEM 600Flooring Membranes

SYSTEM OVERVIEW

NEWTON 603 MESH (M24 & M25)Loose Laid 3mm Flooring Membrane with Meshed Surace

Newton 603 Mesh is high grade ooring membrane with an installation

height of 3.5mm. The white HDPE cuspated core has a polyethylene mesh

above allowing for adhesion of the oor nish to the membrane.

Newton 603 Mesh is loose laid above the substrate and is therefore

uncoupled from the oor ensuring that the oor nish is not affected by

movement or cracking of the substrate.

Newton 603 Mesh is available in rolls 1m x 20m - 20m2 (M24) and

2m x 20m - 40m2 (M25)



Page 20


22/42


NEWTON SYSTEM 700Liquid Applied Floor Coatings

SYSTEM OVERVIEW

System Overview

System 700 is our range of liquid applied protective and decorative

internal ooring products. These products are fast curing and available

in a variety of colours, and are typically used for the refurbishment and

protection of commercial and domestic oors.

NEWTON 701 HB (LM 701)

High Build Epoxy Floor CoatingNewton 701 HB is a two-component solvent free water based epoxy

resin based oor coating developed to provide protective and decorative

properties to concrete, steel and other substrates. The material is

supplied as a two-pack system comprising pre-weighed amounts of base

and curing agent. After mixing together, an easily applied chemical and

abrasion resistant nish is produced. This acts as a waterproof, tough,

chemical resistant oor coating or as an internal lining for concrete or

steel storage tanks containing oils, chemicals, water, etc. It is particularly

suitable for chemical bunds.


Food preparation areas Breweries

Industrial units Warehouses

Garages

Below ground structures where Newton drainage conduits are utilised

NEWTON 702 ECOSEAL (LM 702)Highly Resistant Polyurethane Floor Coating

Newton 702 EcoSeal is a two component, solvent free, high performance

Aliphatic Polyurethane resin which provides a hard yet exible oor

coating, with very high abrasion and chemical resistance. It provides

excellent surface protection to oorings exposed to high wear and trafc.

Newton 702 EcoSeal is supplied as a transparent coating for use abovecoloured bases such as Newton 701 HB or it can be coloured on site with

RAL colours through the addition of pigment pastes and used above a

suitable Newton primer as the stand-alone oor nish. The total absence

of solvents allows for application in unventilated indoor areas. Newton

702 EcoSeal cures to a UV stable gloss nish.


Heavy trafc areas

Industrial factories, depots and warehouses

Indoor tennis courts and recreational areas

Hard wearing nish to other oor coatings

Indoor car parks



Page 21

NEWTON SYSTEM 700 - LIQUID APPLIED FLOOR COATINGS


23/42


NEWTON SYSTEM 800Damp Proofing

SYSTEM OVERVIEW

NEWTON SYSTEM 800 - DAMP PROOFINGSystem Overview

Newton System 800 is a range of BBA approved damp proof membranes

and ancillaries which are quick and clean to install and offer a permanent

solution for damp proong walls.

Newton 805 Newlath and Newton 803 Newtonite meshed membranes

provide a rm key and impermeable barrier on any damp or deteriorating

surface ready for plaster, render or dot & dab plasterboard.

The un-meshed Newton 803 is used where insulation requirements

dictate the use of a timber or steel frame ready for plasterboard. Quick,

clean and proven to work, Newton damp proof membranes offer a

permanent and cost effective damp proong solution.

NEWTON 805 NEWLATH (M9 & M10)5mm Meshed Damp Proong Membrane

Newton 805 Newlath (formerly Newlath 2000) is a BBA approved high

density polypropylene membrane with a rot-proof polythene mesh

heat-welded during the manufacturing process to the surface of one side.

The meshed surface creates a mechanical key to allow the membrane to

be plastered, rendered or to receive dot & dab plasterboard. Newlath can

be applied internally as a means of dealing with all forms of dampnessinherent in structures and externally to properties suffering from driving

and penetrating moisture.

With over two million metres of Newton 805 Newlath installed nationally,

Newlath is a cost effective and permanent method of dealing with

dampness.

Typical Applications

Internally for dealing with rising damp, salts and contaminants within

existing structures.

Externally for protection of brick and masonry structures from driving

and penetrating moisture

Treating dampness in listed buildings as the system is deemed

removable and reversible and is sympathetic to the building fabric. Applied to timber frame properties which require a rendered nish.

Newton 805 Newlath is available in rolls 1.5m x 10m -

15m2 (M9) and 2m x 20m - 40m2 (M10)



Page 22


24/42



SYSTEM OVERVIEW

NEWTON 803 (M19 & M20)Non-Meshed Damp Proong Membrane

Newton 803 is a non-meshed damp proong membrane for use above the

ground. It can be used as an alternative to Newton 803 Newtonite and

805 Newlath where a meshed surface is not required as a surface for

direct plastering or rendering. Newton 803 is typically used where the wall

nish to the damp-proof membrane is timber battens, a dry-lining frame

or block wall.

Newton 803 is 0.5mm thick and has a pattern of raised 3mm studs.

The studs face the wall and create air channels that allow for vapour

equalisation to take place between the membrane and the wall.

Newton 803 is available in roll sizes 2m x 20m - 40m2

(M20) and 1m x 10m - 10m2 (M19)

NEWTON 803 NEWTONITE (M16, M21, M22)3mm Meshed Damp Proong Membrane

BBA approved Newton 803 Newtonite provides a rm key and

impermeable barrier on any damp or deteriorating surface where direct

bonding is not possible. Even poor and random substrates can easily

receive Newtonite.

Newtonite presents a physical barrier between the old surface and thenew internal nish. Unlike many systems it can be punctured when new

wall xings are required. Holes drilled through the material must however

be well sealed with Newton Mastic to stop any dampness

bridging between the existing and new surface.

Newtonite 803 is available in roll sizes:

1m x 10m - 10m2 (M16), 1m x 20m - 20m2 (M21)

and 2m x 20m - 40m2 (M22)

NEWTON 801 FLEXPROOF-X1 (FP1)

Wet-room WaterproongNewton 801 FlexProof-X1 is a highly advanced single component liquid


that is splash proof in minutes and capable of handling severe building

movements and deformations.

Newton 801 FlexProof-X1 has characteristics that allow it to be used

without a primer, without mixing and in weather conditions that preclude

the use of alternatives. When applied by trowel to wet-room walls, 801

FlexProof-X1 provides a continuous highly exible membrane which can

be blinded with sand ready for the tiled nish.

Newtonite 801 FlexProof-X1 is available in containers of 15kg & 26kg



Page 23


25/42



SYSTEM OVERVIEW

NEWTON 800 MESH PLUG (A16)Above ground the Newton 800 Mesh Plug can be used internally and

externally to secure Newton meshed membranes: 805 Newlath and

803 Newtonite. Once the hole is drilled it should be primed with Newton

Mastic sealant to prevent dampness tracking back along the plug.

Size (Width x Length) 7mm x 50mm

Quantity Per Bag 250

NEWTON MULTIPLUG (A1)

Newton MultiPlug is used with Newton 803. Drill a 10mm hole through

the 803 membrane and hammer home with a club hammer. The

MultiPlug can take a 5mm dia screw to allow the xing of battens and

dry-lining frames and the Newton Helix Wall Tie without breaching

the membrane. MultiPlug Pins are sold separately.

NEWTON 800 COB PLUG (A17)

In above ground situations, the Newton Cob Plug is used with 803

Newtonite and 805 Newlath membranes. It has an expanding stem which

provides effective anchorage in a wide range of base materials. Larger

sizes of Newton Cob Plug can be sourced on request.

The ancillaries below are used with the three damp-proong membranes that are included within Newton System

800. Newton 803 is a plain membrane used where a dry-lining frame or a block wall is to be used as the wallnish. 803 Newtonite and 805 Newlath are meshed membranes used where a surface key is required for direct

plastering, rendering or dot and dabbing to the wall membrane. Please read the membrane product data sheets

for more information.

Membrane Fixing Plug Jointing Tape Sealing Drilled Hole Plaster Stop Repairs

803 MultiPlug Newton Overtape Not Required Not required Newton Overtape

803 Newtonite 800 Mesh or

Newtonite Plug

Newton Mesh Tape Newton 800 Mastic Newton 800 Prole Newton Mesh Tape

805 Newlath 800 Mesh or

Newtonite Plug

Newton Mesh Tape Newton 800 Mastic Newton 800 Prole Newton Mesh Tape




Quantity Per Bag 50



Page 24

NEWTON 800 NEWTONITE PLUGS (A20)

Above ground the Newtonite Plugs can be used internally to secure

Newton 803 Newtonite and 805 Newlath membranes. Once the hole

is drilled it should be primed with Newton Mastic sealant to prevent

dampness tracking back along the plug.




26/42



SYSTEM OVERVIEW

NEWTON 800 MASTIC (A18)Newton Mastic is used with 805 Newlath and 803 Newtonite. It is used

to prime the plug hole prior to the xing plug being hammered home,

which serves to stop any bridge happening between the damp or stained

surface and the new surface. Newton Mastic is also used for sealing

around protrusions.

Unit o Sale 0.38 litre tube

NEWTON MESH TAPE (A25)

Newton Mesh Tape is used to joint 803 Newtonite and 805 Newlath

membranes as well as for repairs to the membrane and for sealing

around protrusions. The meshed surface gives a good key for renders

and plasters.

Size (Width x Length) 100mm x 10m

Unit o sale Single units

NEWTON OVERTAPE (A8)

Newton Overtape is used for the jointing of Newton 803 as well as for

repairs to Newton 803 and to seal around protrusions to the membrane.

NEWTON 800 PROFILE (A19)

Newton Prole can be used with 803 Newtonite and 805 Newlath. It

serves as a plaster stop, guaranteeing that the plaster/render will stop

short of the oor.

Size 2m lengths

Unit o Sale Single units

Size (Width x Length) 100mm x 20m

Unit o sale Single units



Page 25


27/42


NEWTON SYSTEM 900Liquid Primers & Sealers

SYSTEM OVERVIEW

NEWTON SYSTEM 900 - LIQUID PRIMERS & SEALERSSystem Overview

Newtons high performance range of liquid applied products are used in

conjunction with System 200 and 700 liquid membranes. They act as

priming agents for a variety of substrates prior to the application of our

specialist waterproong and ooring membranes.

NEWTON 901 HUMIDITY PRIMER (PS 901)Epoxy Primer Suitable or High Humidity Substrate

Newton 901 Humidity Primer is a solvent free two part epoxy resin coating

typically used as a primer for Newton high performance liquid applied or

sprayed roong and ooring products.

Newton 901 Humidity Primer would be chosen as the primer coating

where the substrate contains humidity levels in excess of 4%.

Application

Mix Part A - Epoxy Resin with Part B - Hardener thoroughly with an electric

paddle mixer for 2 min until a milky uniform colour is achieved (pot life of

approx 30 minutes)

Application rate is 0.3 kg per m2 dependent on the quality of the

substrate. Newton 901 Humidity Primer is supplied in 5kg, 10kg and20kg components.

NEWTON 902 (PS 902)Liquid Applied Radon, Gas & Vapour Barrier

Newton 902 is a single component high performance elastomeric liquid

rubber membrane specically designed for providing a radon, gas and

vapour barrier to vertical and horizontal surfaces. Newton 902 is a cost

effective vapour barrier material which can easily be applied via a stiff

brush, roller or airless sprayer to a variety of different substrates including

concrete, mortar, brick, Insulated Concrete Formwork (ICF), ceramics,

steel, zinc or aluminium.

Pre-dampen porous substrates prior to the application of the rst coat.

Application

Newton 902 can be used as a primer for other Newton liquid membranes

when applied in one coat of 0.33kg per m2 or as a gas, vapour and

waterproong membrane with two coats totalling 1kg per m2

Newton 902 is supplied in 5kg, 10kg and 20kg tubs.



Page 26


28/42


NEWTON SYSTEM 900Liquid Primers & Sealers

SYSTEM OVERVIEW

NEWTON 903 PU PRIMER (PS 903)Epoxy Primer or Nonporous Substrate

Newton 903 PU Primer is used for priming non-absorbent substrates,

prior to application of Newton high performance liquid applied roong and

ooring products.

It should be chosen as the primer where the substrate is nonporous such

as ceramic, steel, glass, marble, polished concrete etc.

Newton 903 PU Primer can be applied with roller, brush or cloth to a ratio of

0.1kg per m2

Newton 903 PU Primer is supplied in units 4kg, 9kg or 20kg

NEWTON 904 HP ACCELERANT (PS 904)Humidity Primer Accelerant

Newton 904 HP Accelerant is a clear accelerant additive for exclusive

use with Newton 901 Humidity Primer. The addition of Newton 904 HP

Accelerant to Newton 901 Humidity Primer results in the primer being

cured in 1 to 2 hours (diminishing the risk of alteration by rain, wind, etc.)

The accelerated curing is achieved without any loss in its properties or

changes in the chemical structure of the primer.

Newton 904 HP Accelerant is supplied in 1kg units and has been

designed to be added to a 20kg unit of Newton 901 Humidity Primer.

Add the 1kg unit of Newton 904 HP Accelerant to the 20kg unit of the

901 Humidity Primer once both parts A and B have been already mixed.

Totally mix and homogenise both products together.

Note: After adding 904 HP Accelerant to the 901 Humidity Primer the pot

life is shortened to only 20-30 minutes and the combined product cannot

be reused.

NEWTON 906 MOULD STOP (PS 906)

Mould Steriliser & KillerNewton 906 Mould Stop can eradicate mould in four easy steps. It is

simple to use and as well as killing dangerous mould it prevents regrowth

and eliminates musty odours.

Newton 906 Mould Stop is suitable for walls, ceilings, skirting boards,

window reveals, uPVC window and door frames.

906 Mould Stop kit contains: 1 litre of Mould Stop Steriliser and Killer

Spray, 1 x safety glasses, 1 x pair of disposable gloves, 1 x sponge and

2 x 100ml Mould Stop Paint Additive.

Once mixed Newton 906 Mould Stop will treat between 10 and 15m2



Page 27


29/42


NEWTON FLEXPROOFConstruction Joint Waterproofing

SYSTEM OVERVIEW

NEWTON FLEXPROOFHighly Advanced Single Component Liquid Waterproong Material

Newton FlexProof-X1 forms an elastomeric polymer membrane that is

rainproof in minutes and capable of handling severe building movements

and deformations.

FlexProof-X1 has characteristics that allow it to be used without a primer,

without mixing and in weather conditions that preclude the use of

alternatives.

FlexProof-X1 is a multi-use product and can be applied by trowel or

squeegee to a variety of different surfaces such as concrete, screed and

timber boards to provide a continuous highly exible membrane that is

resistant to water pressures of up to 2 bar (20m) over construction jointsof up to 0.25mm.

Key Benefts:

No mixing required - simply open the packaging and use.

Can be used in sub-zero temperatures and on slightly damp

substrate.

No primer required - saving on primer and labour costs

Single coat application.

100% waterproof, but allows vapour diffusion.

Very exible - Resistant to movement and ssures in substrates.

Excellent adhesion to suitable substrates.

Resistant to temperature variations maintaining its characteristics

between -40C & 90C.

Excellent resistance to the high alkalinity of concrete.

NEWTON FLEXPROOF-X1 (FP1)Construction Joint Waterproong

For the waterproong of construction joints in new-build concrete

construction of basements. When applied by trowel or squeegee over

construction joints in concrete, FlexProof-X1 provides a continuous highlyexible membrane that is resistant to water pressures of up to 2 bar

(20m) over construction joints of up to 0.25mm.

Suitable Substrate:

Construction and movement joints to basement structures built of

concrete.

Retained walls built in concrete or concrete block.

Construction and movement joints to decks and at roofs built of

concrete or timber.

Wet rooms built of concrete, masonry or timber.



Page 28


30/42


NEWTON DIATHONITEInsulating Plaster

SYSTEM OVERVIEW

NEWTON DIATHONITEEco Thermal Plaster with Insulation and Acoustic Properties

Newton Diathonite is a premixed plaster, bre-reinforced with cork

(granular 0-3 mm), clay powders and NHL 3.5 natural hydraulic lime.

The resulting natural compound produces a plaster with unrivalled

thermal and acoustic properties that is both hard wearing and exible

which is ideal for both internal and external applications.

Diathonite, when applied either internally or externally, creates a

seamless thermal barrier which eliminates any risk of cold bridging within

the structure. To achieve very high thermal and acoustic performance,

Newton Diathonite will need to be applied at a thickness that is similar to

those of standard wall insulation.

One of the big advantages of applying Newton Diathonite to existing

properties is that the application can be split between internal and

external application, whereas conventional insulation can only be added

to the inside of the walls and so impacts greatly on the internal space.

It is usual for the internally applied insulation to then have a covering,

such as plasterboard, which further reduces habitable space. By splitting

the application of Diathonite between the inside and outside of the wall,

similar insulation characteristics can be achieved with just half the space

loss of conventional insulation.

Key Benefts

Superb insulation properties thanks to the air spaces created by

natural cork particles included within the plaster

High vapour permeability

Resistant to re: Class 1

Eco-friendly

Can be spray applied allowing for very fast application

Very exible - large elevations can be plastered without cracking

Impressive acoustic characteristics - over twice the performance of

conventional plasters or renders

Typical Applications

As a high performance insulated plaster for both the inside and

outside of external walls

As a sound insulating plaster for both external and internal walls



Page 29


31/42


NEWTON SUMP AND PUMPPumping Product Range

SYSTEM OVERVIEW

NEWTON SUMP AND PUMPSystem Overview

Newton have an extensive range of submersible pumps and pumping

ancillaries. We supply the highest quality pumps available in each class,

for the control of clean ground water, grey water, efuent or sewage.

CLEAN/GROUND WATER PUMPS

NEWTON NP150 (P1)

Medium head and low to medium duty pump. The NP150 is an automatic

pump, with integral vertical oat switch and so is not suitable for use with

our pump control panels. It can be used with Newton Power Converters of

1200W or over to give continual pumping even when the power is out.

The NP150 is supplied with a one way check valve and should be used

with 50mm pressure rated discharge pipe. The pump is sold as pump

only, or as a key component in our Newton Titan-2 packaged pump

system.

3 year manufacturers warranty.

NEWTON CP250 (P31)

The Newton CP250 is a low cost and high quality clean water pump ideally

suited for the removal of ground water from basements and cellars. The

unique vertical operation oat switch ensures that the pumps operate

within the pump footprint removing the possibility of the oat snagging

during operation and allowing the pumps to be used within smaller

sumps. The vertical oat switch is also very exible, allowing the pump

switching height to be adjusted both in height between the on and off

positions, but also in height relative to the pump.

The CP250 is supplied with a one way check valve and and should be

used with 50mm pressure rated discharge pipe.

The pump is sold as pump only, or as a key component in our Newton

Titan-2 and Newton Titan-Pro packaged pump systems.

1 year manufacturers warranty or 3 year Newton warranty with proven

service history.



Page 30


32/42



SYSTEM OVERVIEW



NEWTON CP400 (P32)









The CP400 is supplied with a one way check valve and should be used

with 50mm or 63mm pressure rated discharge pipe. The pump is sold

as pump only, or as a key component in our Newton Titan-2 and Newton

Titan-Pro packaged pump systems.

1 year manufacturers warranty or 3 year Newton warranty with proven

service history.

NEWTON NP400 (P2 & P3)

Available in both manual (P3) and automatic (P2) versions, the NP400 is

the most popular high performance submersible pump in our portfolio.

The NP400 has a unique vertical oat mechanism which can be adjusted

to suit each individual pumping assignment. It can be used with Newton

Power Converters of 1200W or over to give continual pumping even when

the power is out.

The NP400 is supplied with a one way check valve and should be used

with 50mm or 63mm pressure rated discharge pipe. The pump is sold

as pump only, or as a key component in our Newton Titan-2 and Newton

Titan-Pro packaged pump systems.


NP400PP (P13) & NP400LLPS (SP1)

The Newton NP400PP is a high quality puddle pump able to pump water

down to just 1mm. The NP400PP is a manual pump with no switching

control - the pump will run continually when connected to a power supply.

Switching of puddle pumps is problematic because by their nature they

are dealing with low heights of water. This makes conventional switchingdifcult.

The NP400LLPS is the switched version of the NP400PP Puddle Pump.

The NP400LLPS has a small control panel and low level switching

module added to the NP400PP Puddle Pump that will give accurate and

safe switching on of the pump at water levels of just 10mm. The NP400

LLPS will pump down to just 1mm of water depth. The NP400PP and

NP400LLPS are supplied with a one way check valve and should be used

with 50mm pressure rated discharge pipe.


Page 31


33/42



SYSTEM OVERVIEW



Page 32

NEWTON CP750 (P33)









The CP750 can be supplied with a choice of one way valves and should

be used with 50mm or 63mm pressure rated discharge pipe.

The pump is sold as pump only, or as a key component in our Newton

Titan-Pro packaged pump system.1 year manufacturers warranty or 3 year Newton warranty with proven

service history.

NEWTON NP750 (P5 & P6)The Newton NP750 is a high performance pump available as an

automatic pump (P5), or as a manual pump (P6) for use with the CP2

Control Panel. It can be used with Newton Power Converters of 3000W to

give continual pumping even when the power is out.

For increased duty in a twin pump system, separate discharge lines

should be used. The NP750 is sold as pump only, or as a key component

in our Newton Titan-Pro packaged pump system and should be used with

50mm or 63mm pressure rated discharge pipe.


EFFLUENT PUMP (NOT SEWAGE)

NEWTON NP400W (P4)

The Newton NP400W is a medium head and medium performance pump

specically placed within the Newton pumping range for when dishwasher,

washing machine or bath/shower waste is to be removed from thesump. It is an automatic pump with a specially designed adjustable oat

arrangement that cannot be fouled by hardened soaps etc. It can be

used with Newton Power Converters of 1200W or over to give continual

pumping even when the power is out.

The NP400W is sold as pump only, or as a key component in our Newton

Titan-Pro packaged pump system and should be used with 50mm and

63mm pressure rated discharge pipe.



34/42





Page 33

SEWAGE PUMPS

NEWTON SP750 RANGER (P9)

The Newton SP750 Ranger is a low head and high performance sewage

pump for the removal of sewage, efuent, waste water and ground water

with suspended soft solids of up to 50mm.

The Newton SP750 Ranger is primarily used as the standard pump in our

Trojan sump systems but can also be used as a stand-alone pump within

formed concrete sumps and should be used with 63mm pressure rated

discharge pipe.


NEWTON FLYGT DXG (GRINDER) (P14 & P16)

The Newton Flygt DXG (Grinder) is a high performance submersible

grinder pump which cuts solids in sewage into smaller bits that can easily

pass through the impeller and discharge pipes.

The Newton Flygt DXG is primarily used as the standard pump in our

Trojan sump systems but can also be used as a stand-alone pump within

formed concrete sumps and should be used with 50mm pressure rated

discharge pipe.


Available in Automatic (P14) or Manual (P16) versions.

SEWAGE LIFTING STATION

TROJAN SEWAGE PUMPING SYSTEM (TR1-TR12)

Newton Trojan systems are specialist packed sewage systems based upon

a 610mm diameter sump with depth options of 1000mm and 1500mm.

The Trojan systems are supplied as either single or twin pump systems

using the Newton 750 Trojan (Vortex) or Newton Flygt DXG (Grinder).

A hole cutter and 1 x 110mm wall ange is supplied allowing for accurate

on-site positioning of the invert connection.

Note: The Trojan System is not supplied with a High Water Level Alarm -

Alarm and pump control options are available at extra cost.

SYSTEM OVERVIEW


35/42



CLEAN/GROUND/EFFLUENT PUMPING SYSTEMS

TITAN-PRO WHITE (TPW)

The Newton Titan-Pro White is designed specically to be used with

Newton System 500. The adjustable neck allows for the sump to be

installed at a xed height relative to the slab so that the connection in

from the Newton drainage system and the pump discharge line are made

above the concrete.

The sump can be used with single pumps, twin pumps and twin pumps

with twin discharge lines for greater pump efciency.

The Titan-Pro White is available with the following pumps: CP250,

Newton Waterproofing Systems

Documents

Transcript of Newton Waterproofing Systems