Nemo Outdoor - Keysight€¦ · nd u at Page 1 fl˛˚˝˙ˆˇˇ˛ Nemo Outdoor PCTEL HBflex...

Find us at www.keysight.com

D ATA S H E E T

Nemo OutdoorPCTEL HBflex Scanner

Test and Monitor Complex Cellular Environments and ProtocolsNemo Outdoor from Keysight Technologies, Inc. is an unparalleled network

measurement and optimization solution for perfecting the air interface of wireless

networks. It collects measurement results and geographical coordinates,

and these measurement results further provide valuable information for

network planning, roll-out, tuning, verification, optimization, maintenance, and

benchmarking purposes. Nemo Outdoor is always among the first-to-market with

support for the very latest technologies. This data sheet lists parameters and

features available with PCTEL’s HBflex scanner and Nemo Outdoor.

Supported Bands• GSM 850, E900, 1800, 1900 MHz

• WCDMA 850, 900, 1700, 1800, 1900, 2100 AWS, 2600 MHz

• CDMA 450 MHz (band class 5), 800 MHz (band class 0, 10), 900 MHz (SMR) (band class 9), 1900 MHz (band class 1), AWS (band class 15)

• EVDO 450, 800, 1900 MHz

• TD-SCDMA band 34 (2010-2025 MHz)

• LTE FDD bands E-UTRA bands 1-8, 10-14, 17-21, 23-32, 65-68, 70, 71, 252, 255

• LTE TDD bands: E-UTRA bands 33-46, 48

• WIFI bands: 2.4-2.483 and 5.15-5.85 GHz

• 5G NR:

- Sub 6 GHz bands: n1-3, n5, n12, n25, n28, n38, n41, n66, n71, n75, n77-n79

- 24.25-29.5 GHz bands: n257, n258, n261

- 37-40 GHz bands: n260


5G NRFrequency scanning options• Channel style (BW):

- NR bands 1-3, 5, 12, 25, 28, 38, 41, 66, 71, 75 = 5 kHz

- NR bands 77, 78, 79 = 15 kHz

• Scanner averaging (1:1, 1:2, 1:4, 1:8, 1:16)

Pilot scanning parameters • Signal type

• Band

• NR ARFCN

• PCI (NR physical cell identity 0-1007)

• BI (NR beam index 0-63)

• SCS (NR subcarrier spacing 15 kHz- 240 kHz)

• Cyclic prefix (Normal/ Extended)

• SSS (Secondary Synchronization Signal)

- SS-RSRP (dBm)

- SS-RSRQ (dB)

- SS-SINR (dB)

- SS-Delay spread

• PSS (Primary Synchronization Signal)

- PS-RSRP (dBm)

- PS-RSRQ (dB)

• PBCH-DM (Demodulation Reference Signal of PBCH)

- PBCH DM-RP (dBm)

- PBCH DM-RQ (dB)

- PBCH DM-SINR (dB)

• SSB (Synchronization Signal Block)

- SSB-RP (dBm)

- SSB-RQ (dB)

- SSB-SINR (dBm)

Pilot scanning options • MIB decoding

• SIB1 decoding

LTEMeasurement modes• Frequency and pilot scanning

Frequency scanning parameters• Channel number

• Carrier RSSI

Frequency scanning options• Channel style (BW): 200 kHz (Narrow); 1.4 (1.08), 3

(2.7), 5 (4.5), 10 (9), 15 (13.5), 20 (18) MHz (Wide)


Pilot scanning parameters (synchronization channel)• Channel number

• Physical cell ID (PCI)

• P-SCH and S-SCH RP

• P-SCH and S-SCH RQ

• CINR

• Cyclic prefix (CP)

• Time offset

Pilot scanning parameters (reference signal)• Channel number

• Carrier RSSI

• PCI

• RSRP

• RSRQ

• RS CINR

• RS cyclic prefix

• RSRP, RSRQ, and CINR per antenna port

• Time offset

• System Information Block 1 message (SIB1)

• Master Information Block message (MIB)

• MIMO specific parameters

- MIMO mode

- RSRP, RSRQ, and CINR per antenna port


combination

- 2x2 MIMO condition number

- Single layer open loop CQI

- Single layer open loop throughput (bit/s)

- Single layer closed-loop CQI

- Single layer closed-loop throughput (bit/s)

- Dual layer open-loop CQI 0

- Dual layer open-loop throughput 0 (bit/s)

- Dual layer open-loop CQI 1

- Dual layer open-loop throughput 1

- Dual layer closed-loop SM CQI 0

- Dual layer closed-loop throughput 0 (bit/s)

- Dual layer closed-loop SM CQI 1

- Dual layer closed-loop throughput 1 (bit/s)

Pilot scanning options• Channel style (BW): 1.4 (1.08), 3 (2.7), 5 (4.5), 10

(9), 15 (13.5), 20 (18) MHz (Wide)

• Cyclic prefix (auto detect, normal, extended)

• Data processing method (peak, aggregate)

• Sampling ratio (1:1, 1:2, 1:4, 1.8)


• RSSI threshold

• Top-N number of carriers (1-24)

• Top-N number of cells (PCIs) (1-16)

• CINR

• Time offset

• Sync signal

• Reference signal

• MIMO

• Layer 3 decoding (requires an option, see a list of options at the end of this document)

eMBMS measurements• MBSFN Area ID

• PMCH channel number

• PMCH RSRP

• PMCH RSRQ

• PMCH CINR

• PMCH RSSI

NB-IoTMeasurement modes• Top-N Narrowband RS

• Narrowband PSS

• Narrowband SSS

NB-IoT parameters• RS: NRS_RP, NRS_RQ, NRS_CINR,

• PSS: NPSS_RP, NPSS_RQ, NPSS_CINR

• SSS: NSSS_RP, NSSS_RQ, NSSS_CINR

• Time offset

Operation modes• In-band

• Guard band

• Stand-alone

Channel bandwidth• 180 kHz

Max number of PCIs• 16

WCDMAMeasurement modes• Frequency and pilot scanning

Frequency scanning parameters• Channel number

• Carrier RSSI

Frequency scanning options• Channel style WCDMA 200/3840 kHz (CW/Wide)



Pilot scanning parameters (synchronization channel)• P-SCH Ec/N0

• P-SCH RSCP

• S-SCH Ec/N0

• S-SCH RSCP

Pilot scanning parameters (Top-N)• Channel number

• RSSI

• CPICH scrambling code (SC)

• CPICH Ec/N0

• CPICH RSCP

• CPICH SIR

• CPICH delay spread

• CPICH time of arrival (TOA)

• SIB decoding

Pilot scanning options (Top-N)• CPICH Ec/N0 Threshold

• Data processing method (peak, aggregated)

• Pilot measurement mode

- High speed: enables maximum CPICH pilot measurements per second

- High dynamic: enables extended CPICH Ec/I0 measurement range

• Sampling ratio configuration (1:1, 1:2, 1:4, 1:8)


• WCDMA carriers (1-24)

• Top-N scanning (1-32 pilots)

• Pilot time of arrival measurements

• Pilot delay spread measurements

• CPICH SIR

• P-SCH measurements

• S-SCH measurements

• SIB decoding

GSMFrequency scanning parameters• Channel number

• RSSI

• BSIC

• Cell info decoding

- Enables the decoding of BCCH Type 3 message, including Cell ID, MCC, MNC, and LAC parameters for up to 512 channels simultaneously

- Decoding is supported on numerous user-selectable BCCH frequency channels

Frequency scanning options• Channel style (30 kHz/200 kHz)

• BSIC decoding

• BSIC threshold


• SI decoding

• Neighbor list decoding

CDMA/EVDOFrequency scanning parameters• Channel number

• Carrier RSSI

Frequency scanning options• Channels to be scanned

• Channel style (BW 30kHz, 1.25MHz)


PN scan general information (Top-N)• Measures and reports strongest PNs in

descending order up to 32 PNs

• Measures and reports up to 24 channels including both CDMA and EVDO


• Provides user-selectable peak/aggregate Ec/I0

• Measures and reports pilot delay and delay spread for each PN

• Multiple simultaneous Top-N PN scans supported

PN scan parameters (Top-N)• Channel number

• PN

• Delay spread

• Carrier RSSI (pilot mode)

• Ec/I0

• RSCP

PN scan options• Top-N number of pilots (1-32)

• Data processing method (peak, aggregated)

• Pilot window mode: offset, centered, edge



• Ec/I0 threshold

• Pilot increment

• Delay

Standard specification• Standards

- CDMA2000® 1xRTT

- CDMA EV-DO Revision A

TD-SCDMAPilot scanning parameters (PCCPCH)• Channel number

• PN

• Carrier RSSI

• Ec/I0

• RSCP

• SIR

• Time offset

Pilot scanning options• Top-N scanning (MAX 32 pilots)

• MAX 34 channels

• Measurement mode: peak/aggregate



• Time offset

• SyncDL

• SIR

WIFIWIFI scanning parameters• WLAN band

• Bandwidth

• Channel number

• WLAN protocol (e.g. 802.11a)

• BSSID (MAC address)

• SSID

• WLAN security mode (e.g. WEP)

• WLAN beacon interval

• RSSI

• Channel utilization

Additional FeaturesSpectrum analysis• User selectable parameters

- Start/stop frequency or center frequency and bandwidth

• Measurement rate (with one channel)

- 80 samples/s

- > 270 MHz/sec (with single sweep scan)

• Spectrum monitor accuracy

- ±0.05 ppm GPS locked and ±0.1 ppm GPS unlocked (ambient)

• Frequency range: 10 MHz to 6 GHz

• Sensitivity: –124 dBm

• Resolution bandwidth: automatically adjusted to


the closest value of 5, 10, 20, 40, 80, 160, 200, 400, and 800 kHz

• Max. number of sample counts: 2560

• Measurement range

- > 90 dB

Scanner data averaging• Scanner calculates average results for all

parameters. Available options are 1:1, 1:2, 1:4, 1:8, and 1:16.

Band scan (blind scan)• Band scan feature supports the following

technologies: GSM, WCDMA, LTE, CDMA, EVDO, TD-SCDMA and WIFI

• GSM: Channel, RX level, MCC, MNC, Operator

• WCDMA, CDMA, EVDO, TD-SCDMA: Channel, SC/Pilot number, RX level, Ec/No, MCC, MNC, Operator, LAC, RSCP

• LTE: Channel, PCI, BW, RSSI, RSRP, RSRQ, MCC, MNC, Operator, TAC

• WIFI: Channel, RX level

WCDMA pilot pollution analysis• Pilots causing possible pilot pollution are shown in

real time

• The user can define the following thresholds: polluter level window from best active set cell (dB), Ec/N0 active set best below threshold (dB), RSCP active set best above threshold (dBm), and pilot count threshold

• WCDMA pilot pollution analysis parameters

• Source system

• Source band

• Source channel number

• Pilot pollution scr code

• Pilot pollution Ec/N0

• Pilot pollution Ec/N0

• Pilot pollution RSCP

GSM interference analysis• GSM co-channel and adjacent channel analysis

is done in real time during a measurement and playback with Nemo Outdoor.

• Interference detection is done based on GSM terminal and GSM scanner measurements and these measurements are combined together

• GSM interference analysis parameters

- Cell type: serving, co-channel, adjacent channel

- Band

- BSIC

- RX level


Technical Performance

RF characteristics

Frequency range Sub 6Ghz - 10MHz – 6GHz

mmWave : N257 (26.5-29.5 GHz), N258 (24.25-27.5 GHz), N260 (37-40 GHz)

Internally generated spurious response

-105 dBm (typical)

Conducted local oscillator -55 dBm (typical)

RF operating range In-band -20 dBm max

Desensitization Adjacent channel > 50 dB (20 MHz RBW)

Safe RF input range ≤ +0 dBm

Frequency accuracy ±0.05 ppm (GPS locked); ± 0.1 ppm (GPS unlocked)

Intermodulation-free dynamic range

2 tone @ -30 dBm, 40 GHz, -50 dBc (typical)

5G NR characteristics

Measurement modes NR Top N Signal : Synchronization channels (P-SS/S-SS) & PBCH

Data modes PCI, PSS_RP [dBm] ,SSS_RP [dBm], PSS_RQ [dB] ,SSS_RQ [dB], SS_CINR [dB], RSPBCH_RP [dBm], RSPBCH_RQ [dB]. RSPBCH_CINR [dB], SSB_RP [dBm], SSB_RQ [dB], SSB_CINR [dB], SSB_idx

Sub carrier spacing 15/30/120/240 KHz

Max. number of channels 24

Measurement rate 5/sec

Dynamic range (CINR) PSS/SSS CINR

CINR

-10 to + 40 dB PBCH DMRS

-8 to + 40 dB

Min. Detection Level RP -135 dBm (SCS @15 KHz)

Relative Accuracy (CINR) PSS/SSS CINR ±2 dB


LTE characteristics (FDD and TD-LTE)

Measurement Modes Top N Synchronization Channel Reference Signal, (P-SCH/S-SCH),

and Resource Block (Wideband, Subband); Layer 3 Reporting;

Top N eMBMS Multicast Reference Signal; Unicast

Synchronization Channel Reference Signal and (P-SCH/S-SCH)

Data Modes RP, RQ, CINR, Cyclic Prex, Time Osets, Delay Spread;

MIMO: Condition Number, ECQI, EPUT

eMBMS: Area TD, Cluster ID, Frame Conguration

Channel Bandwidths 1.4 / 3 / 5 / 10 / 15 / 20 MHz

Max. Number of Channels 24 (16 for eMBMS)

Receive Modes SISO; MIMO (2x2, 4x2)

Transmit Antenna Congurations

1, 2, 4 (with path measurement)

Measurement Rates Sync channel RS

Multicast RS

LTE FDD: 50/sec; TD-LTE: 25/sec

eMBMS: 2/sec

Dynamic Range (CINR): @ 10 / 15 / 20 MHz

RS

P-SCH/S-SCH

Multicast RS

–26 to +40 dB

–10 to +18 dB

–9 to +30 dB

Min Detection Level RSRP -140 dBm (RSRP @ 15 MHz)

Relative Accuracy (CINR) P-SCH/S-SCH & RS ±1.0 dB


NB-IoT characteristics

Measurement Modes Top N NRS (Narrowband Reference Signal),

NPSS (Narrowband Primary Synchronization Signal), and

NSSS (Narrowband Secondary Synchronization Signal)

Data Modes NRS - RP, RQ, RSSI, CINR, Time Oset. NPSS - RP,

RQ, RSSI, CINR. NSSS - RP, RQ, RSSI, CINR, Time Oset

Operation Mode In-band, guard band, stand-alone

Channel Bandwidths 180 kHz

Measurement Rates 190 ms

Dynamic Range (CINR) NRS -10 to +40 dB

Min Detection Level NRS RP -138 dBm

Relative Accuracy (CINR) NRS ±2 dB

Max. Number of PCIs 16

WCDMA characteristics

Measurement Modes Top N Pilot, Layer 3 Reporting

Data Modes lo, Ec/Io, Aggregate Ec/Io, SIR, Rake Finger Count,

Time Offset, Delay Spread

Channel Bandwidths 200 kHz / 3.84 MHz

Max. Number of Channels 24

Measurement Rate 100/sec (High Speed Mode); 50/sec (High Dynamic Range Mode)

Top N CPICH Dynamic Range (Ec/Io)

-26 dB

Min Detection Level -120 dBm (High Dynamic Range Mode)

Relative Accuracy ±1 dB


GSM characteristics

Measurement Modes Color Code, Layer 3 Reporting

Data Modes BSIC, C/I, RSSI

Channel Bandwidths 30 kHz / 200 kHz

Measurement Rate up to 200 BSIC decodes/s

Dynamic Range +2 dB C/I

Min BSIC Detection Level

–110 dBm


CDMA and EV-DO characteristics

Measurement Modes Top N PN

Data Modes Ec, lo, Ec/Io, Aggregate Ec/Io, Pilot Delay, Delay Spread

Channel Bandwidths 30 kHz (Narrow/CW)

1.25 MHz (Wide)

Max. Number of Channels 24

Measurement Rate CDMA: 25/sec; EV-DO: 18/sec

Top N PN Dynamic Range, Ec/Io CDMA: -28 dB; EV-DO: -18.5 dBm

Min. PN Detection Level CDMA: -130 dBm; EV-DO: -120 dBm



WiFi characteristics

Radio Configuration 802.11a/b/g/n, 802.11a/b/g/n/ac

Data Modes Signal Strength, Noise Level, SNR, Channel Number, Channel

Bandwidth, BSSID, Device Name, SSID, Security Protocol,

802.11 Media, Beacon Interval, Channel Utilization, Throughput

Frequency Range 2.4 – 2.483 GHz; 5.15 – 5.85 GHz (subject to country regulations)

Measurement Rates 9/sec (Typical); 5/sec (Typical) for 802.11ac

Power measurements

Measurement rate (max) LTE

NB-IoT

UMTS

GSM

CDMA and EV-DO

TD-SCDMA

5G NR

11,050 ch/sec

4,250 ch/sec

4,250 ch/sec

4,250 ch/sec

8,500 ch/sec

4,250 ch/sec

11,050 ch/sec

Dynamic Range -120 to -20 dBm @ 30 kHz

Absolute Accuracy ±1 dB (across Basic RF Input Power Range)

Channel Bandwidths 5 kHz to 20 MHz in 2. 5 kHz Increments

Measurement Rate 1,000 MHz/sec @ 5 MHz ( Typical)

Absolute Accuracy ±1 dB (across Basic RF Input Power Range)

Measurement Range > 90 dB

Measurement Rate (Single Sweep) > 270 MHz/sec

Accuracy ±1 dB (across Basic RF Input Power Range)

This information is subject to change without notice. © Keysight Technologies, 2018-2019, Published in USA, June 20, 2019, 5992-3517EN


Learn more at: www.keysight.com

For more information on Keysight Technologies’ products, applications or services,

please contact your local Keysight office. The complete list is available at:

www.keysight.com/find/contactus

Physical characteristics

Operating temperature range 0 to +50°C

Storage temperature range –30 to +80°C

Dimensions (W×H×D) 10.10” D x 6.50” W x 4.40” H (255.3 mm D x 165.1mm W x 111.5 mm H)

Weight 7.26 lbs (3.3 kg)

Power consumption 25 W MAX

Input voltage +9 to +17 VDC

Safety (CE) IEC 62368-1

EMC EN 301 489 -1

Shock and Vibration MIL-STD-810G, SAE J1455

RoHS Compliant (6/6)

http://www.keysight.com/find/dmm

Nemo Outdoor - Keysight€¦ · nd u at Page 1 fl˛˚˝˙ˆˇˇ˛ Nemo Outdoor PCTEL HBflex...

Documents

Transcript of Nemo Outdoor - Keysight€¦ · nd u at Page 1 fl˛˚˝˙ˆˇˇ˛ Nemo Outdoor PCTEL HBflex...