Nemo Outdoor Training slides.pptx
-
Upload
anonymous-jwdwu55 -
Category
Documents
-
view
231 -
download
3
Transcript of Nemo Outdoor Training slides.pptx
8/19/2019 Nemo Outdoor Training slides.pptx
http://slidepdf.com/reader/full/nemo-outdoor-training-slidespptx 1/21
July 26, 2015
NEMO Outdoor Air Interface measurement tool
8/19/2019 Nemo Outdoor Training slides.pptx
http://slidepdf.com/reader/full/nemo-outdoor-training-slidespptx 2/21
Contents
Introduction of NEMO outdoor.
How to build a project.
How to configure different entities.
How to make the test plan.How to generate report using Nemo analy e.
8/19/2019 Nemo Outdoor Training slides.pptx
http://slidepdf.com/reader/full/nemo-outdoor-training-slidespptx 3/21
Introduction
Nemo Outdoor is an effecti!e tool for tracing digital networks. It collects
measurement results and geographical coordinates "when used with a #$% recei!er&
and stores them on a hard disk.
Nemo Outdoor is a laptop'based dri!e test tool which supports o!er ()* terminals
and scanning recei!ers from !arious !endors and all major network technologies.
Measurement results pro!ide useful information for network optimization +
verification + and maintenance purposes.
,esults can be efficiently and easily !iewed with -cti analy er software which is to
be used in this project
Nemo Outdoor uses licensed technology from !arious manufacturers.
8/19/2019 Nemo Outdoor Training slides.pptx
http://slidepdf.com/reader/full/nemo-outdoor-training-slidespptx 4/21
Important things to notice while using Nemo OutdoorInstalling and running Nemo Outdoor re/uires administrator rights.0o not use the Nemo Outdoor test mobile1s keypad to make or answer calls when the Nemo Outdoor systemis running.2ith %amsung terminals the key tone !olume should be turned off. Otherwise+ the mobile can dial a wrongnumber.2ith Nokia #%M+ #$,%+ and E0#E terminals the test display "Net Monitor& must not be acti!ated.
In !oice /uality measurements the !olume of the mobile headset must be adjusted to correct le!els. $leaserefer to the Nemo 3oice 4uality #uide document.
0o not place stickers containing metal on the mobile because it may lower the transmission power of themobile.
-fter the measurements ha!e been completed and it is desired to take the Nemo Outdoor test mobile into
normal use+ it must be powered off and on again to deselect5deacti!ate the Nemo Outdoor triggered e!entsin the mobile.
6se only the supplied connecting cable+ included with the Nemo Outdoor+ for connecting the Nemo Outdoortest de!ices to the computer1s 6%7 port.
2hen using the Nemo Outdoor test mobile for measurement use+ the battery operation time is reduced fromnormal use. 8he best operation times will be achie!ed when the batteries are regularly charged anddischarged as instructed in the mobile user manual.
8/19/2019 Nemo Outdoor Training slides.pptx
http://slidepdf.com/reader/full/nemo-outdoor-training-slidespptx 5/21
1. How to build a Project8he 9irst $age that will appear when you open NEMO outdoor .
On the page the following Tasks can be created.
1.Create New evice Configuration!" 0escribes the -uto 0etection of de!ices that are already
hooked into the $C.
#.Open a evice configuration!" 0isplays the pre!iously loaded 0e!ices in a workspace.
$.%oad a measurement!" 2hich 0escribes the archi!al of the pre!iously measured task.
&.'orkspace!" which describes the built in workspaces templates 3iews that you can select for your
project.
(. etails!" 2hich 0escribes about the details of COM and Modem $orts used on your pre!iously used
workspace.
8/19/2019 Nemo Outdoor Training slides.pptx
http://slidepdf.com/reader/full/nemo-outdoor-training-slidespptx 6/21
:.: Opening a 2orkspace.
8he 9irst %tep we need to take is to
Open a workspace from the 7uilt in
templates. -s the Image on the
left shows we ha!e lists of
2orkspaces+ which includes
;.wor <+ for new workspace
creation.
Steps:- File>>>>> Open
Workspace>>> Select the
“*.worx” or “.worx”.
8/19/2019 Nemo Outdoor Training slides.pptx
http://slidepdf.com/reader/full/nemo-outdoor-training-slidespptx 7/21
(. How to configure different entities of Our $roject
(.: Configuration Manager
DeviceConfgurati
on
BaseStation
Files
UserInter ace
(Scripts andOther
Customizedwindows
8he Configuration Manager shows the
o!erall system properties of NEMO outdoor.
-fter Opening a Test 2orkspace +2e ha!e
to configure important Entities of the
project on the Configuration Manager
%uch ='
8/19/2019 Nemo Outdoor Training slides.pptx
http://slidepdf.com/reader/full/nemo-outdoor-training-slidespptx 8/21
(.:.: 0e!ice Configuration
In order to -dd the 0e!ices needfor our $roject we need to go tothe ) evice* %ection ofConfiguration Manager . -fterpressing the plus sign we will bepresented with three 0e!ice typeswe can apply of our project.
1.+hone
#.,canner$.-+,
8/19/2019 Nemo Outdoor Training slides.pptx
http://slidepdf.com/reader/full/nemo-outdoor-training-slidespptx 9/21
(.:.:.:Configuring a phone
8he andler Information is specified on the list ofhandlers that ha!e been installed on your Computerfrom the Configuration Manager %ystem entity.
-ll the handlers for " +hones/-+,s and ,canners &that ha!e been purchased can be found on the NemoOutdoor installation %oftware. Each de!ice has its ownhandler+ and in order to use them in Nemo Outdoor+you must ha!e the corresponding handler installed+ Inour case we ha!e ;4ualcomm< as a handler for $honeswe use on our project.
-fter we select )0ualcomm* we will be presentedwith a window that will allow 6s to configure ourde!ices Manually.
8/19/2019 Nemo Outdoor Training slides.pptx
http://slidepdf.com/reader/full/nemo-outdoor-training-slidespptx 10/21
9irst thing we need to do is to
go to the Computer
anagement in order to get
the CO information of the
8erminal then on the eviceanager/ the drop down
menu of the 0e!ice Manager
) odems* and )+orts* are
important sections to notice.
-fter connecting your phone to
your computer you need to seethe COM port and Modem port
numbers Occupied by the
terminal. If your 0e!ice does
not appear+ you to need make
sure you ha!e installed the
terminal5 de!ice dri!er
correctly.
In our Case the Com port
number is either CO 2 or
CO 3 +Modem port is CO 4 .
8/19/2019 Nemo Outdoor Training slides.pptx
http://slidepdf.com/reader/full/nemo-outdoor-training-slidespptx 11/21
-s the image illustrates we need to
select the 8race port and Modem
port of the 0e!ice specific
Information.
Circuit switched dial"upconnection > +acket switched
dial"up connection list bo es gi!e
a list of all the dial'up connections
that ha!e been configured on your
computer. If you are making C% or
$% data measurements. ?ou canselect a specific 0ial up that is
already configured before. ?ou can
lea!e the default 3alues be and
mo!e on for C% tests.
8he Measurement $roperties dialog
contains se!eral pages and the
contents depend on the de!ice
-eneral + easurement
,ettings +notification and ,cript
for the de!ice can be configured
along with the Configuration of the
de!ice.
8/19/2019 Nemo Outdoor Training slides.pptx
http://slidepdf.com/reader/full/nemo-outdoor-training-slidespptx 12/21
-fter -pplying the Configuration
parameters we can see that the status
of the $hone will be displayed as
) evice is working +roperl5* and is
;attached< to the network accordingly.
%etting the easurement +roperties
will be ne t if we didn1t already $erform
this action before connecting the de!ice
on the pre!ious slide.
On the -eneral Tap ='we ha!e todefine the Network name6can be afriendl5 name or operator7/ 8T, filedefinition and ,ubscriber Noinformation.
8/19/2019 Nemo Outdoor Training slides.pptx
http://slidepdf.com/reader/full/nemo-outdoor-training-slidespptx 13/21
(.:.( 7ase %tation 9ile 8T, file 69ngineering
+arameter7 defines the base
station file that will be displayed on
the map. If you ha!e a #$%
recei!er connected to the system+
you can !iew the measurement!ehicle on the map and a line will
be drawn from the measurement
!ehicle to the acti!e base station.
8he 9ile format that can be loaded
is 6:.nbf or :.csv7.
?ou can prepare the 78% 9ile
according to the 78% file format
NEMO outdoor accepts and make
sure you sa!e it as C%3"Comma
0elimited& 9ile and upload to the
%ystem.
8/19/2019 Nemo Outdoor Training slides.pptx
http://slidepdf.com/reader/full/nemo-outdoor-training-slidespptx 14/21
8here are some pre defined scripts
a!ailable that you can select from the
drop down menu but you can also
create your own in the %cript Editor .
8he scripts in the same group are
synchroni ed with each other. 0e!ices
can be assigned for certain script
groups. 7y default the script group is
selected as @NoneA+ but the user can
also create new script groups by
selecting @New groupA in the %cript
group drop'down menu+ and typing
the name of the new script group in
the field as the Image on the left
illustrates.
(.:.B %cript $roperty
8/19/2019 Nemo Outdoor Training slides.pptx
http://slidepdf.com/reader/full/nemo-outdoor-training-slidespptx 15/21
(.:.B.: C% testing script making 2hen we Configure script
files we can select the
;script Editor< and select
or add the kind of test we
want to perform as the
image shows.2e must also configure
the 8est count 5 ;epeat
,cript after adding a test
plan. -s the image on the
left shows. - script file
has ; .nsf< file type we
must save the script after
finishing the
configuration.
8/19/2019 Nemo Outdoor Training slides.pptx
http://slidepdf.com/reader/full/nemo-outdoor-training-slidespptx 16/21
-s the Image -bo!e shows we can run the script specific for a selected de!ice or we can generally run
all the scripts for all de!ices at once.
Note that after you ha!e acti!ated the script+ for the de!ice+ you cannot control the measurement
manually until the script is finished or you interrupt the script by clicking the %top %cripts button.
-fter running the script you can see the script running status and some output comments on the
output tab of the ;output !iew< on the bottom of the application.
Normally when you start the scripts Nemo will automatically start recording the log file unless you are
doing an idle test and you need to record with out a script configuration. ?ou can change the location
of the log file sa!ing place or it will be sa!ed on the NEMO tools folder of your C=5dri!e < ,esults<
folder.
8/19/2019 Nemo Outdoor Training slides.pptx
http://slidepdf.com/reader/full/nemo-outdoor-training-slidespptx 17/21
• 2hen we want to make $% teststhere are certain steps we needto follow. 9irst thing we need todo insert out modem into thecomputer and install the
necessary dri!er for the de!iceand go to ;de!ice manager.< • On the Modems section of the
we will find the modem weconfigured listed+ %elect andright click on themodem +<$roperties<+ On the-d!anced 8ab +E tra settings+E tra intili ation commands fillin the “at+cgdcont=1,"ip",“APN“ in our case -$N is etc.com
atDcgdcont :+FipF+Fetc.comF
(.:.B.: $% testing script making
8/19/2019 Nemo Outdoor Training slides.pptx
http://slidepdf.com/reader/full/nemo-outdoor-training-slidespptx 18/21
Ne t step is we need to create5set up a dial up connection using the modem we just configured
as follows.
8/19/2019 Nemo Outdoor Training slides.pptx
http://slidepdf.com/reader/full/nemo-outdoor-training-slidespptx 19/21
2hen we configure the $% testde!ice we need to make surethat we select +the 0ial upconnection we ha!e created onthe per!ious page with the0e!ice1s selected modem.
8/19/2019 Nemo Outdoor Training slides.pptx
http://slidepdf.com/reader/full/nemo-outdoor-training-slidespptx 20/21
8he data measurement system has two modes= %end and ,ecei!e. In the %end mode+ themeasurement unit sends data packets to the 98$ ser!er in the ,ecei!e mode !ice !ersa. If youare using an 98$ ser!er+ the measurement unit uploads "%end mode& or downloads ",ecei!emode& test files to or from the 98$ ser!er. If you are using an H88$ ser!er+ the measurement unitcan only recei!e files .
0uring the measurement+ the user will be able to monitor data throughputs and error rates on
different network layers.
8/19/2019 Nemo Outdoor Training slides.pptx
http://slidepdf.com/reader/full/nemo-outdoor-training-slidespptx 21/21