MTS000010%3ATS+TSS+Tablesaw+w%2Fo+Scoring+

2

Dear Woodworker:

Thank you for your purchase and welcome to the Laguna Tools group of discriminating woodworkers. I understand that you have a choice

of where to purchase your machines and appreciate the confidence

you have in our products.

Every machine sold by Laguna Tools has been carefully designed and

well thought through from a woodworkers perspective. I cut on our bandsaws, lathes, table saws and combination machines. Through

my hands-on experience, I work hard to make our machines better.

I strive to give you machines that inspire you to create works of art.

Machines that are a joy to run and work on. Machines that encourage your performance.

Twenty years ago Laguna Tools was founded to introduce European woodworking machines to the North American woodworker. Today,

we offer high-performance machines with innovative solutions that

meet the needs of woodworkers and their ever-evolving craft.

I started Laguna Tools as a woodworker, I still am.

Thank you again for becoming a Laguna Tools customer.

Torben Helshoj

President and Founder - Laguna Tools

Imagination, Innovation and Invention at work.

3

Table of contents

Safety Rules

Warranty

Noise emission

Specification sheet

Receiving your machine

Unpacking your machine

Introduction to your machine

Assembly and set up

Where to locate your machine

Operating your machine

Maintenance

Troubleshooting

Accessories

Electrical drawing

Spare parts

Exploded view drawings and parts lists

4

Safety Rules

As with all machinery there are certain hazards involved with the operation

and use. Using it with caution will considerably lessen the possibility of

personal injury. However, if normal safety precautions are overlooked or

ignored, personal injury to the operator may result. If you have any

questions relative to the installation and operation, do not use the equipment

until you have contacted your supplying distributor.

Read carefully before operating the machine.

1. Keep the working area clean and be sure adequate lighting is

available.

2. Do not wear loose clothing, gloves, bracelets, necklaces or

ornaments. Wear face, eye, respiratory and body protection devices as

indicated for the operation or environment.

3. Be sure that the power is disconnected from the machine before tools

are serviced or an attachment is to be fitted or removed.

4. Never leave the machine with the power on.

5. Do not use dull, gummy or cracked cutting tools.

6. Be sure that the keys and adjusting wrenches have been removed and

all the nuts and bolts are secured.

5

Limited Warranty

New woodworking machines sold by Laguna Tools carry a one-year warranty from the

date of shipping. Laguna Tools guarantees all new machines sold to be free of

manufacturers defective workmanship, parts and materials. We will repair or replace

without charge, any parts determined by Laguna Tools, Inc. to be a manufacturer’s

defect. We require the defective item/part returned to Laguna Tools. In the event the

item/part is determined to be damaged due to lack of maintenance, cleaning or

misuse/abuse the customer will be responsible for the cost to replace the item/part, plus

all related shipping charges. This limited warranty does not apply to natural disasters,

acts of terrorism, normal wear and tear, product failure due to lack of maintenance or

cleaning, damage caused by accident, neglect, lack of or inadequate dust collection,

misuse/abuse or damage caused where repair or alterations have been made or attempted

by others.

Laguna Tools, Inc. is not responsible for additional tools or modifications sold or

performed (other than from/by Laguna Tools, Inc.) on any Laguna Tools, Inc.

woodworking machine. Warranty may be voided upon the addition of such noted tools

and/or modifications, determined on a case-by-case basis.

Normal user alignment, adjustment, tuning and machine settings are not covered by this

warranty. It is the responsibility of the user to understand basic woodworking machinery

settings and procedures and to properly maintain the equipment in accordance with the

standards provided by the manufacturer.

Parts, under warranty, are shipped at Laguna Tools, Inc’s cost either by common carrier,

UPS Ground service or similar method. Technical support to install replacement parts is

primarily provided by phone, fax or email. The labor required to install replacement

parts is the responsibility of the user.

Laguna Tools is not responsible for damage or loss caused by Freight Company or other

circumstances not in our control.

Only new machines sold to the original owner are covered by this warranty. For

warranty repair information, call 1-800-332-4094.

Copyright 2010 Laguna Tools, Inc

** Warning – no portion of these materials may be reproduced without written approval

from Laguna Tools, Inc.

All documentation subject to change without notice

6

Noise emission Notes concerning noise emission

Given that there exists a relationship between noise level and exposure times, it is not

precise enough to determine the need for supplementary precautions. The factors

affecting the true level of exposure to operators are clearly the amount of time exposed,

the characteristics of working environment other sources of dust and noise etc. For

example, adjacent machines in other words the level of ambient noise. It is possible that

exposure level limits will vary from country to country.

Specification

Blade 12”max x 5/8” bore

Max cut height 12” blade 3 ¾” [2 ½” at 45 deg]

Max cut height 10” blade 2 ¾” [2” at 45 deg]

Dado capacity 13/16”

Main motor 3,5 hp single phase 220 volts 3450 rpm

Breaker 20 amp

Electrical cable [not supplied] Up to 20’ 10-3 20’ to 50’ 8-3

Scoring motor [Optional] 1,2 hp single phase 220 volts 3450 rpm

Scoring blade [Optional] 120mm x 5/8” bore

Cast iron [ground] table size 31 ½” x 21 ½”

Miter slot ¾” x 3/8”

Extension table pressed steel with ribs and legs 31 ½” x 35”

Sliding table out rigger table [Optional] Yes

Cutting width on rip fence 50”

Slider length 4’ 2”

Slider travel 5’ 11”

Weight TS 630 lb

Weight TSS 730 lb

Machine footprint 4’ 10” x 3’ x 2’ 10”H

Machine footprint 4’ 10” x 7’ x 2’ 10”H

Dust port 4”

Large throat plate with leveling screws Yes

Blade guard Yes

7

Standard equipment supplied

with TS

Spare blank throat plate insert

Rip fence

Extension table with legs

Blade guard

Tool kit

Options for TS Miter gauge


Sliding table

Mobility kit

Scoring unit

Standard equipment supplied

with TSS


Extension table with legs

Blade guard

Tool kit

Sliding table

Miter fence with flip stop and clamp

Miter fence 90-degree flip stop.

Options for TSS Miter gauge


Mobility kit

Scoring unit

Sliding table out rigger table

Flip stop

Clamp

Straight line rip plate

24” fence

24” fence with telescopic extension

5 hp single phase [Leason]

Miter fence 90-degree flip stop.

8

TSS floor plan

TS floor plan

9

Receiving your machine.

Note. It is probable that a third party will deliver your machine.

Before you unpack your new saw you will need to first inspect the packing, invoice and

shipping documents supplied by the driver. Insure that there is no visible damage to the

packing or the machine. You need to do this prior to the driver leaving. All damage must

be noted on the delivery documents and signed by you and the delivery driver. You must

then contact the seller [Laguna Tools] as soon as practical. If damage if found after

delivery, contact the seller as soon as practical.

Introduction to Table saws

This Table saw is designed to give you years of safe service. Read this owners manual in

its entirety before assembly or use.

Parts of the Table saw.

The table saw does not have many parts. The major parts are discussed in this manual. If

you are not familiar with the table saw take the time to read this section and become

familiar with the machine.

Identification.

There is a plate at the back of the machine listing all the manufacturing data including the

serial number, model, etc.

10

Cabinet

The cabinet has a large footprint and is a welded construction manufactured from heavy

gauge steel plate [4mm [0.16”] thick]. The cabinet houses all the parts of the machine and

the heavy construction ensures that the saw is stable. This weight also helps to absorb any

vibration that is produced during cutting.

Table

The table is manufactured from cast iron [cast iron is a live material and will move over

time] and is provided with a leveling system to ensure that your table remains flat during

the life of the machine. This system allows you to stress the table and take out any

warpage that occurs over time. The table is attached to the cabinet and located with dowel

pins that are removable should adjustment be needed between the miter slot and the saw

blade. On the TS the table is split so that should you require you can fit a sliding table at

a later date.

Trunnion

The trunnion assembly is attached and doweled to the cabinet. It is a heavy cast iron

construction. It houses the motor, saw spindle, riving knife, tilt mechanism, and vertical

movement adjustment. This is the heart for your saw.

The advantage of attaching the trunnion to the case rather than the table is that its weight

is supported by the cabinet and will not twist or distort the table.

Electrical system

The electrical system consists of an electrical motor, start switch, stop switch and

contactor. No cable or plug is supplied as the length of the cable and the type of plug will

be dependant on your installation.

Rip fence.

The rip fence is a “T” square design that gives superior rigidity and is adjustable for

parallel to the blade.

Dust collection.

Dust collection port is located at the back of the machine and is 4” diameter. It connects

to the bottom of the trunnion assembly and collects the sawdust as it leaves the blade.

You will need a dust collection system with a minimum of 1000 cubic feet per minuite.

Throat plate.

On the TS the throat plate is solid cast iron with an insert that can be slid in or out for

easy change between inserts. It is adjustable for level to the table.

The TSS has a fixed throat plate that has inserts that clip in and out. It is also adjustable

for level to the table.

11

Sliding table.

The sliding table is manufactured from heavy aluminum extrusion. The table is supported

by ball bearings that roll on polished round steel rods. The clearance between the ball

bearings and the polished round steel guide rods is adjustable. The advantage of the

bearing system is that there is only point contact between the balls and the rods, which

virtually eliminate the problem of dirt, building up and the sliding table will remain

accurate for many years. When wear takes place the polished round steel rods can be

rotated and present a new surface to the ball bearing.

Miter gauge [Optional].

The miter gauge has a cast iron body with an aluminum fence. The miter gauge is

adjustable for angle and has dowel holes every 15 degrees for quick accurate setting. The

fence is movable in relation to the body so that you can adjust it to suite the job.

Miter fence TSS.

The miter fence is manufactured from cast iron and heavy-duty gauge aluminum

extrusion. It is supplied with a flip stop and a job clamp. It can be set at any angle and has

an adjustable 90-degree flip stop that is fitted to the side of the sliding table.

Mobility kit [Optional]

The mobility kit is easy to fit and the machine is located directly on the floor when the

mobility kit is not in use.

Scoring unit [optional]

The scoring unit can be purchased with the saw or fitted as an option later. The scoring

unit has a separate motor and is adjustable vertically and horizontally. All machines are

supplied with locating / fixing holes and faces machined to accept a scoring unit.

The machine should never be started with both motors engaged. The main motor

must be started and when at full steed then the scoring motor started. If both motors are

started at the same time excessive load is put on to the contactor and it will burn out.

12

Where to locate your machine.

Before you remove your machine from the pallet select the area where you will use your

machine. There are no hard and fast rules for its location but below are a few guidelines.

1/ There should be an area at the front and back of the machine suitable for the length of

wood that you will be cutting.

2/ Adequate lighting. The better the lighting the more accurate and safely you will be able

to work

3/ Solid floor. You should select a solid flat floor, preferably concrete or something

similar.

4/ Close to power source and dust collection.

5/ Allow an area for the storage of blanks and cut jobs.

Unpacking your machine.

To unpack your machine you will need tin snips, knife and a wrench.

1/ Using the tin snips, cut the banding that is securing the packing box [If fitted].

WARNING: EXTREME CAUTION MUST BE USED BECAUSE THE BANDING

WILL SPRING AND COULD CAUSE INJURY.

2/ Dismantle the box or remove the row of screws around the base of the box and lift the

box off the pallet. You will need two people to lift the box off the pallet.

3/Using the knife cut the plastic wrap. The extension table, fence and accessories that

were ordered are in the box.

4/ Remove the base mounting bolts that secure the machine to the base of the box.

5/ It is recommended that the machine be removed from the pallet by lifting it with a

hoist or forklift. Remove the pallet and lower to the floor. [To lift with a hoist, four lifting

hooks are provided that fit into the holes at the bottom of the body.]

The machine can be lifted using a forklift truck, sliding it onto the forks or by using a

"SLING" with a lifting capability of 2000 Kg [4400lb]

If no lifting device is available you can fit the mobility kit [if ordered] build a temporary

ramp and roll the machine off the pallet.

Note The machine is heavy; ensure that you have sufficient people.

Note: If you have any doubt about the described procedure seek professional assistance.

Do not attempt any procedure that you feel is unsafe or that you do not have the physical

capability of achieving.

13

Fitting the optional mobility kit [If ordered]

Slide the axel through the lower inside holes on the side of the machine and fit the spacer

[large washer] onto the axel.

Fit the wheel assembly, nut and washer on to the axel.

To activate the moblity kit, insert the handle into the tube and rotate so that the machine

is lifted. When in the up position insert the sliding pin.Repeate on the other side of the

machine.

Fit the cast iron bracket to the front of the machine with the bolts provided into the

tapped holes. Move the machine by inserting the transport bar and lifting.

14

Assembly and set up

What you will receive with the machine.

Lifting hooks and tools

Optional mobility kit

Fence system

Optional straight line rip bracket

Extension table and spare throat plate

Miter fence

15

Cleaning the machine.

Remove the rust protection grease with WD 40 or similar solvent

It is important that you remove all the grease and re lubricate with a Teflon bases

lubricant as Teflon has less tendency to attract sawdust and cause clogging. You should

also wax the table, as this also protects the cast iron from rust.

Leveling the machine.

Leveling bolt

The machine is provided with 4 leveling bolts. Move your machine to its final position,

and using a sprit level on the table, adjust the leveling bolts so that the table is level in

both directions. Ensure that the machine does not rock.

Switch box shown with optional scoring

switch

Vertical control handle

The start / stop switches are located on the side of the machine next to the blade vertical

control handle. The knob in the center of the control handle, is a lock that locks the blade

in the vertical position selected.

Angle control handle

The handle on the front of the machine, controls the angle of the saw blade. The angle

read out is on the side of the machine by the vertical control knob. When moving the

blade to an angle, the yellow-hinged dust plate MUST be closed. Damage may occur if

the yellow hinge plate is not closed.

16

Switch cover shown open

To start your machine, release the red stop button by moving the button to the right. The

door will be released and the green button will be accessible. Press the green button, and

the machine will start. To stop the machine, press the red button.

The machine should never be started with both motors engaged. The main motor

must be started, and when at full steed, then the scoring motor started. If both motors are

started at the same time, excessive load is put on to the contactor, and it will burn out.

Riving knife adjustment

Riving knife adjustment

To adjust the riving knife for different diameters of saw blade, loosen the clamp screw,

and slide the knife up or down or laterally to suite the blade selected. Once adjustment is

completed, ensure that the screw is re tightened.

To adjust the riving knife parallel and inline with the blade, four adjusting screws are

provided.

Locking rod

Fitting blade Arbor spacer

17

To fit a blade, disconnect the saw from the power. Move the arbor to the maximum up

position. Rotate the saw arbor so that the hole in the arbor lines up with the hole in the

saw table. Insert the locking rod, and loosen the arbor nut. Remove the large clamping

disc, and fit the blade. When refitting the clamping disc, ensure that the key lines up with

the key way. The nut must be tightened, and the locking rod removed before starting the

machine.

Note. The arbor has a left hand thread.

Note. The arbor is shown with the spacer removed. The spacer is only removed when you

fit a dado cutter. It is left on the arbor when fitting a saw blade.

Dust cover clips

Locking rod

Loosen

To release the yellow dust cover, release the clips at both ends. Never move the saw

arbor with the dust cover loose, as it could become damaged.

Guard in up position

Guard in down position

Fit the saw blade guard, and fit a dust hose if required. The size of dust hose should be 1

½”.

Fitting a blade

18

Leveling screws

TS throat plate Insert

The throat plate is made from cast iron, and has a phenolic insert. A spare insert is

provided that you can machine to suite your requirements [Dado, Zero clearance, etc].

There are two types of throat plate, TSS and TS. To adjust the TS throat plate, adjust the

leveling screws so that the throat plate is level with the table. To remove the insert slid

out as shown.

Straight edge

TSS throat plate

To adjust the TSS throat plate, place a rule [straight edge] across the table so that it

extends across the throat plate. Each clamp screw is provided with jacking screws, and by

19

loosening the clamp screw, and adjusting the jacking screws, the plate can be adjusted for

level to the table, and for parallel to the table. Ensure that the clamping screws are tight

before you use the saw.

Retaining clip

Insert TSS throat plate

On the TSS, releasing the clips and sliding the insert towards the blade will remove the

insert. Note. The blade will have to be in the down position. To fit a new insert, slide into

the throat plate and you will hear a click as the catches engage.

Dust port

The machine has a dust port at the back of the machine close to the ground. It takes a 4 “

diameter hose, and needs to be connected to a dust collector with a capacity of 1000

cubic feet per minute minimum [The stronger the dust collector the better].

20

Dado cuter

Fitting the dado cutter

Dado cutter

To fit the dado cutter, disconnect the machine from the power and remove the arbor nut,

clamping disc, and spacer.

Fit the dado and lock in position with the clamp washer and arbor nut. Ensure that the

lock rod is removed before you start the machine. A blank throat plate is supplied that

you can machine to suit the dado that you are using. Optional additional throat plate

inserts are available.

Extension table legs

Extension table

Extension table fixing bolt

Fitting the extension table

Fit the legs to the table prior to fitting the table to the saw.

Attach the table to the main table with the fixing bolts provided. DO NOT FULLY

TIGHTEN THE BOLTS.

Scorin

g

cutter

21

Straight edge

Extension table Jack screw

Using a straight edge, adjust the legs so that with the straight edge flat on the main table

the part of the extension table that is directly above the legs is level with the table.

Above the table fixing bolts are leveling screws. Adjust the leveling screws so the table is

level with the main table, and fully tighten the fixing bolts.

Note. The table is attached to the side angles, and after you have completed all the

adjustments, you will have to drill through the holes in the angles, and attach the table to

the angles, with the screws and nuts provided. Do not drill the holes at this point in time.

Note. Do not level the table or attach the angles until the machine is in the final position.

Fence tube Side angle

Tube fixing bolts

View from underside of tube and

angle

Fit the angle iron rails to the side of the main table. Make sure that the angle with the

fence holes is on the side of the machine with the on / off switch. Use the countersunk

screws to attach the angle to the main table.

The angle on the other side of the machine is attached with hex bolts.

Fit the fence tube to the angle with the hex bolts and washers from the under side of the

angle. It is recommended that this be assembled with two people, as the tube has a

tendency to slide off the angle during assembly.

The angles will have to be adjusted vertically and this is covered latter.

22

Electrical connection

Note the machine is not supplied with an electrical plug or cable, as the type of plug and

cable, will be dependant on the installation. A qualified electrician must carry out the

electrical installation.

Switch box open

Ground

Fitting the electrical cable. The electrical cable is fitted as shown. The recomented cable

size 10.3 gauge for runs of up to 20’. For longer runs up to 50’use cable 8-3 gauge.

Recommended breaker size is 20 amps.

On the machine you will see a wire that is yellow and green, this is the ground wire, the

other colored wires are power. It does not matter what color combination you use. Green

and yellow is ground; all other wiring is power (there is no neutral). On single phase the

wiring can be interchanged as you wish; it would not affect the rotation of the motor. The

direction of rotation of machines with a single: phase supply is predetermined during

production.

Before starting the machine

1/ Read and understand the instruction manual before operating the saw.

2/ If you are still not thoroughly familiar with the operation of the saw get advice from a

qualified person.

3/ Make sure the machine is properly grounded and that the wiring codes are followed.

4/ Do not operate the machine while under the influence of drugs, alcohol, and medicine

or if tired.

5/ Always wear eye protection, safety glasses or a safety shield, and hearing protection.

6 /Wear dust mask; long term exposure to the fine dust created by the saw is not healthy.

7/ Remove your tie, rings, watch, and all jewelry. Roll up your sleeves, and never ware

loose clothing. You do not want anything to get caught in the saw.

8/ Make sure that the guards are in place and use them at all times. The guards protect

you from coming in contact with the blade.

9/ Make sure that the saw blade teeth point in the correct direction.

10/ Stop the machine before removing the scrap piece from the table.

11/ Always keep your hands and fingers away from the blade.

12/ Make sure that you use the proper size and type of blade.

Ground /earth

Switch box open

23

13/ Hold the work piece firmly against the table. Do not attempt to saw stock that does

not have a flat surface facing down.

14/ Use a push stick at the end of a cut. This is the most dangerous time, because the cut

is complete and the blade is exposed. Push sticks are commercially available.

15/ Hold the wood firmly, and feed it into the blade at a moderate speed.

16/ Turn off the machine if you have to back the material out of an uncompleted or

jammed cut.

Machine test

Now is the time to test the machine.

Note. Never start the main saw motor and the scoring motor at the same time. It will

damage the magnetic contactor. Always start the main motor and when running at full

speed then start the scoring motor.

Stop switch

Optional Scoring switch

1/ Check that the machine is clear of all tools, and other loose objects.

2/ Check that all the adjusting and locking handles are tight.

3/ Check that there is no blade fitted, it is far safer to test the machine with out a blade

fitted.

4/ Start the machine by pressing the green start switch.

5/. Saw arbor is now turning.

6/. Now is the time to check that the safety switch is functioning correctly before you fit a

blade.

7/ With the machine running [no blade fitted] operate the red stop switch by pressing

towards the machine. The motor should have the power removed and slow down.

8/ If the safety switch fails to operate correctly do not use the machine until the fault has

been corrected.

Before you cut any wood read the safety rules at the front of this manual

24

To fit the measurement tape.

Marking the fence tube

Assembling the measurement tape

1/ Clean the steel tube with solvent to remove all traces of grease and dirt.

2/ With a blade fitted, and the power disconnected from the machine, fit the fence to the

tube and push it up against the blade so that it is just touching.

3/ Mark a point on the tube with a pencil or pen at the curser line.

4/ Remove the fence. Line the end of the tape up with the pencil mark and peel off the

backing in short sections, sticking the measurement tape to the tube.

Fine adjusting slots

Fine adjustment of the hair line can be done in a number of ways but the most effective

way is to lock the fence [1”] and to cut a piece of wood. Measure the wood and adjust the

hairline read out.

Note. Do not over tighten the read out as you may crack the plastic.It is possible to adjust

the read out closer to the tape by inserting washers between the two parts of the readout.

Make sure that the plastic is not in contact with the tape at any point along its travel.

25

Lublicate the non painted surfaces of the tube with wax or teflon lubricant. This will

ensure that the fence runs smoothly and that the tube is protected from rust.

Adjusting the fence vertically parallel to the saw table.

Adjusting Wrench

Squaring the fence

The angle tube assembly will have to be adjusted vertically to ensure that the gap

between the fence and the table is even along its travel. With the fence close to the blade

place a piece of material 1/16” thick on the table under the fence close to the locking

handle. Loosen the screws that attach the angle to the table, leaving the screw furthest

away from the fence tight. Bring the tube angle assembly up so that it touches the [2]

pads on the underside of the fence, and then tighten the screw close to the fence. Move

the fence to the end of the saw table and repeat. Once the fence is set, tighten all the angle

clamping screws.

Note. It is not critical that the gap under the fence is parallel. It is critical that the rub pad

at the end of the fence is the only part of the fence that touches the table.

Drill through the holes in the steel angle and attach the table to the angle.

You will have to remove the guide tube to drill the holes and then refit it.

Squaring the fence.

A simple way to align the fence is to put a straight edge in the miter slot and align the

fence to the straight edge. If adjustment is required, [2] adjustment screws are provided.

When using the adjustment screws, only move them a small amount at a time. A small

amount of movement on the screw gives a large amount of movement on the fence.

Squaring the fence

26

TSS sliding table

Push pull handle

The push pull handle is fitted under the table for shipping and will have to be removed

and re fitted to the side of the table.

To release the table, remove the red transport brackets [One at each end of the table] and

withdraw the table lock knob.

The table will now slide.

Table end push pull handle

Red transport bracket

Miter fence flip stop Table lock knob

Fit the push pull handle with the screws provided, at the end of the table.

Push pull handle

27

Optional straight line rip stop

Adjusting screws Lock handles

Fit the optional straight-line rip stop at the end of the table as shown.

The optional side extension table, comes with the clamp bar attached. Loosen the ratchet

handles and slide the bar into the slot on the side of the side of the sliding table. Attach

the table and level as follows

.

Straight edge Vertical adjusting screw

To adjust the optional side extension table, lay a straight edge level on the sliding table,

and extended over the side extension table. Loosen the two clamping handles; adjust the

vertical adjustment screws so that the edge of the side extension table is level with the

sliding table. Re-clamp and re-check with the straight edge.

To get the side extension table parallel with the sliding table adjust the two plastic screws

located under the table. Only adjust the screws with the ratchet clamp handles loose.

Side table adjustment

28

Miter fence locking screw

hole

Miter fence flip stop

The miter fence [Cross cut fence] is fitted into the sliding table slot and locating by

tightening the lock screw into the hole in the table slot. Fit the clamp shaft through the

casting into the “T” bolt and tighten.

The machine is provided with a fence stop [shown in the up and down position] that is

factory set. Some adjustment may be necessary and can be achieved by loosening the

lock nut, adjusting the bolt, and then re-clamping the lock nut.

Wooden block Flip stop

Flip stop

Assemble the clamp as shown by screwing the centre post into the “T” bar.

Note. The wood in the view above is resting on the wooden block at the front of the fence

and also on the flip stop.

The miter fence can be fitted to the far end of the table and a short “T” bolt is supplied

that can be used as a reference stop. You will have to move the cast iron miter angle to

the opposite of the fence extrusion.

29

Fine tuning the miter fence.

Several methods are acceptable to fine-tune the fence but we have found that the

following is a very practical way to achieve a square panel.

1/ Clamp the fence locked at 90 degrees against the stop.

2/ Clamp a sheet onto the sliding table and cut a straight edge [edge “A”]. Mark “A”.

3/ Move the sheet so that edge “A” is tight against the fence, clamp in position, cut edge

“B” and mark “B”.

4/ Flip the sheet so that edge “A” is still against the fence but edge “B” is furthest away

from the saw blade, cut edge “C” and mark “C”.

5/ If the sheet is cut square edge B and C should be parallel. Check this by measuring

across the width of the sheet at both ends.

Note. This method will double the amount of error and any adjustment that is required

should be halved. Also the stop is closer to the table than the end of the sheet, so only

adjust the flip stop in very small amounts. Example. You are using a 2’x 2’ sheet and you

are out of parallel by 1/16”, adjust the stop =- 0,01” and repeat the cuts.

First cut

Second cut

Third cut

Measure both ends

Sliding table carriage adjustment.

The sliding table comes factory set, should the table be out of alignment due to shipping

movement, see the maintenance section for adjustment procedure.

30

Optional miter gauge.

Jack screw Clamp screw

Optional miter gauge Dowel pin

The miter gauge has an adjustable pointer; it also has a dowel pin that locks the miter

gauge at 15-degree positions. The fence can be moved to different positions on the miter

gauge to suit the job that you are doing. The fence is cut at 45 degrees at the end to

enable the job to be supported close to the blade when cutting at 45 degrees.

To adjust the pointer, loosen the clamp screw, adjust the pointer and re tighten the clamp

screw.

To move the fence to a different position on the miter gauge, loosen the clamp screws.

Slide the fence to the required position, and re clamp in position.

If you need to move the fence so that the steel clamp block is not supported by the fence,

a jackscrew is provided to hold the steel block parallel.

Optional scoring unit.

Parts you will receive

Scoring casting disassembled

The optional scoring can be fitted as follows

Disassemble the scoring casting as shown.

Scoring body disassembled

31

Push the shaft through the casting so that the dowel pin lines up with the slot in the bush.

Make sure that the spring is in position.

Assemble the stop bushing, and the screw in the back of the casting.

Assemble the vertical adjustment assembly on the back of the trunnion assembly.

Fit the locking bolt.

Use a straight edge line up the two flanges as shown and tighten the locking bolt.

Fitting the adjustment screw

Fit the double threaded allen set screw as follows.

Push the assembly back as far as it will go and hold in position.

Thread the double threaded set screw in by hand until it contacts the inner thread.

Using an allen key continue to screw the screw in while slowly allowing the pressure of

the screw to push the casting forward.

Once the thread has engaged you can release the casting and continue to tighten the

screw.

Care must be taken during this assembly as you could damage the thread.

Vertical adjustment screw

Vertical adjustment access hole

Vertical adjustment screw

Lining up the scoring unit

32

Motor support shaft

Motor shaft nut

Assemble the motor to the support shaft.

Push the support shaft through the trunnion and tighten the nut ensuring that the washer is

fitted. DO NOT OVER TIGHTEN THE NUT, AS THE MOTOR MUST BE ABLE

TO MOVE.

Drive belt

Spring

Spring shaft

Assemble the spring, shaft and drive belt as shown.

33

Fitting the scoring switch

With the power disconnected, fit the switch and attach the wiring as detailed in the

diagram at the back of the manual.

Note. Never start the machine with both motors engaged at the same time. It will

damage the magnetic contactor.

Note. The electrical box is provided with a cable gland at the back to allow the cables to

enter the electrical box.

Once the cabling has been completed, attach the cables to the cabinet with the cable ties

provided.

Tighten the cable gland to ensure that sawdust will not enter the switch box.

Fitting the scoring blade.

Shims

Blades

Clamp screw

Adjusting screw

Spring

34

Fit the scoring blade.

Note. Scoring blades are supplied with shims that are used to adjust the width of the

scoring blade, to suite the saw blade that you are using.

Note. The scoring blade rotates in the opposite direction to the main blade.

Adjust the blade so that it is 1/16’ above the saw table. Access to the vertical adjustment

is through the hole in the table [Shown in previous view].

If the scoring blade is cutting too far left or right, loosen the clamp screw and move the

adjustment screw in or out.

Note. The adjustment is very fine.

Dado cutter

Scoring blades Scoring shims and spacers

Fitting Dado scoring [Optional].

If you dado laminates or plywood, it is an advantage to score the surface to prevent

chipping. The scoring unit can be used to do this as follows.

1/ Measure the width of the dado cutter or cut a slot with the dado and measure the slot.

2/ Fit the inside blade of the scoring set onto the shaft, and select shims and spacers to

suit the slot widths [less the width of the two scoring saw blades].

3/ Place the shims, and the outside blade on to the scoring unit shaft, and lock in position

with the nut and washer.

4/ Adjust the height of the scoring cutter so that it is 1/16” above the table.

5/ Make a trial cut on a piece of scrap.

6/ Check that the inside cutter of the scoring unit is cutting inline with the inside cutter of

the dado cutter, and adjust if required.

7/ Check that the outside cutter of the scoring unit is cutting in line with the outside cutter

of the dado and adjust the shims / spacers if required.

Note. The scoring blade rotates in the opposite direction to the main saw blade.

Hold

shaft with

allen

wrench

35

Maintenance and troubleshooting

All tools and machines require regular maintenance, and the table saw is no exception.

This section details the general maintenance and care of your table saw. In general we

recommend that you only use a Teflon based lubricant on the table saw. Regular oil

attracts dust and dirt and the Teflon tends to dry and has fewer tendencies to accumulate

dirt and saw dust on your machine .We also recommend that you wax the table to help

prevent rust.

Weekly maintanince.

1/ Check all nuts and bolts are tight

2/ Clean the machine, and check that the dust hose is clear. Make sure that all moveing

parts are clean and free from saw dust and dirt.

3/ Lubricate all moveing parts with a Teflon based lubricant.

4/ Wax the table and all none painted parts.

Drive belt tensioning Lock nuts

Drive belt

The drive belts should last for many years [depending on the usage] but need to be

inspected regularly for cracks, cuts and general wear. If damage is found replace both

belts. Never replace only one belt, and only replace the belts with a matched pair.

To re-tension the belts, loosen both lock nuts. The weight of the motor should put enough

tension on the belts. Then tighten the lock nuts. The belts come factory set but after about

8 hours of use, the belts could need to be re-tensioned, as they will have bedded into the

“V” grooves.

Table insert

The table insert [throat plate] is made of a soft material, and is designed not to damage

the blade should they come in contact. If the blade slot becomes too wide, or the insert

becomes damaged by the blade it should be replaced.

Bearings.

All bearings are sealed for life, and do not require any maintenance. If a bearing becomes

faulty replace it.

36

Rust

The table saw is made from steel and cast iron. All none painted surfaces will rust if not

protected. It is recommended that the table be coated with wax. All moving none painted

surfaces should be lubricated / protected with a Teflon based lubricant.

Limit stop

Scoring unit fitted

Limit stop

Yellow dust cover

Tilt mechanism stops.

The machine is provided with two stops that limit the travel of the tilt mechanism. Both

stops come factory set, but should adjustment become necessary, it can be achieved by

loosening the lock nuts and adjusting the allen set screws.

Sliding table adjustment for vertical level with the main table.

Straight edge

Sliding table

The sliding table comes factory set and should be +_ 0,02” above the main table.

Should the sliding table need to be adjusted use the following procedure.

37

Do not attempt this procedure unless excessive movement has taken place during

shipping.

Top nut

Sliding table adjustment Bottom nut

1/ Lock the sliding table in position with the table lock knob.

2/ Using a straight edge across the sliding table check the gap between the straight edge

and the main table at both ends of the man table.

3/ If adjustment is needed loosen the lower nuts ¼ turn only. Do not loosen the top nuts

4/ Adjust the top nuts so that the gap under the straight edge is parallel and at about

0,02”.

5/ Check that all the top nuts are in contact with the support steel and that there is no

rocking.

6/ Tighten the lower nut and re check. If fine-tuning is required repeat procedure.

Sliding table adjustment for parallel with the saw blade.

Wood at front of saw blade

Wood at back of saw blade

The table must run parallel with the saw blade. The gap between the edge of the sliding

table and the table is not important.

To check if the table is running true, clamp a piece of wood [1” x 1” or 2” x 2”] to the

table using the miter fence clamp. Cut the wood slowly. The teeth of the saw blade

should make contact with the front and the back of the blade evenly.

38

A second way to check is to measure the distance between the miter slot and the slot in

the sliding table. The miter slot is parallel with the saw blade and is a good reference

point.

If adjustment is needed proceed as follows.

1/ Loosen three of the lower clamp nuts. Do not adjust the top bolts, as this will affect

the level of the sliding table. Leave one of the bolts that is close to the main table tight.

2/ Swivel the table towards or away from the main table depending on the direction of the

adjustment that is needed. Note only do very small adjustments.

3/ Tighten the three loosened bolts and re check.

4/ If readjustment is necessary repeat the procedure.

Sliding table adjustment for bearing / steel rod clearance.

Screw “X”

Screw “Y”

The sliding table mechanism is designed with 8 ground steel rods, ball bearings run

between the steel rods. The table comes factory set but if there is excessive side

movement adjustment can be made as follows.

1/ Extend the table to one end. The ball carriage will be at the opposite end.

2/ Move the table side to side to check for excessive movement.

3/ Loosen the allen screw [X] and tighten allen screw [Y]. The screws must be adjusted

in pairs, and 2 pairs of screws cover the range of the ball carriage.

Note. The screws should be adjusted in small steps as damage could be caused.

Note. That the [X] screws must be tight before you check for side movement.

4/ Move the table so that the next two pairs of screws are covered by the ball carriage,

and repeat the adjustment procedure.

5/ Continue until all the screws have been adjusted.

39

Sliding table ground steel rods damaged or warn.

Remove end cover

Clamp screws Steel rods

If the steel rods become damaged or warn, a new face can be presented to the ball

bearings as follows.

1/ Loosen the clamping screws at each end of the sliding table.

2/ With a brass rod, knock the rod out +_ 1”.

3/ Rotate the rod +_20 degrees.

4/ With the brass rod, knock the rod back level with the end of the table, and retighten the

clamping screws.

5/ Repeat until all the rods have been turned.

Vertical mechanism tight.

Guide plate

Bearing plate

1/ Check that nothing is jamming the mechanism

2/ Check that the worm gear and screw are clean and lubricated.

40

3/ Check that the guide plate is not jamming. Clean and re lubricate. Ensue that you clean

the whole guide plate by moving the saw arbor to fully up and fully down, cleaning the

exposed part of the guide plate.

4/ Inspect the guide plate and bearing plate for ware and damage. If damaged or warn,

replace.

Clamp screws Leveling screws

Lock nut Adjusting screw

5/ If the worm gear is warn or excessively tight adjustment is provided.

Note. Contact your supplier before attempting to adjust the worm gear / screw clearance.

You could cause damage or your warrantee could be affected.

Tilt mechanism tight

Tilt worm gear and screw

1/ Check that nothing is jamming the mechanism

2/ Check that the worm gear and screw are clean and lubricated.

3/ If the worm gear is excessively tight or worn, adjustment is provided.

Note. The adjustment mechanism is similar to that shown above for the vertical

mechanism.

Note. Contact your supplier before attempting to adjust the worm gear / screw clearance.

You could cause damage or your warrantee could be affected.

41

Miter gauge slot to saw blade adjustment.

Table spring pin

Trunnion spring pin

Table adjustment bolt [Jack]

The table and the trunnion assembly are doweled to the body of the saw with 2 [each]

spring pins. The pins stop movement during transport.

The miter slot is factory set to run parallel with the saw blade, but, if movement has taken

place during transportation of your saw, you will have to knock the spring pins through

the table and the body of the saw, and loosen the table to body clamping screws. Adjust

the table to the saw blade and re-clamp the table to the body. Do not refit the spring pins.

Do not remove the spring pins in the trunnion assembly.

It is easer to move the table to the saw blade rather than the trunnion assembly to the

miter slot.

Note. When loosening the table from the body, only loosen the clamp bolts. Do not

change the setting of the table adjustment bolts. You could affect the flatness of the

table.

Trunnion spring pin Trunnion clamp bolt

Adjusting the table for flatness.

The table is made from cast iron, which is a live material and will move over time.

To help keep your table flat, and to compensate for the cast iron movement, the table is

provided with five adjustment points [one at each corner and one in the middle of the

table] The system uses a jack and clamp. The outer bolt [Jack] has a hole through the

middle, which allows the clamp screw to pull the table down directly onto the jack.

If your table flatness has moved you can compensate as follows.

42

Table dip in the middle.

Note only adjust the table in very small steps over a period of time. Cast iron is a

very brittle material and will break if over stressed.

1/ Lay an engineer’s straight edge across the table.

2/ Using feeler gauges measure the gap under the straight edge.

3/ Remove the back panel to gain access to the underside of the machine.

4/ Loosen the table clamp bolt in the middle of the table and tighten the table adjustment

bolt [jack]. Only move the bolts a very small amount.

5/ Check the amount that you have moved the table using the straight edge and the feeler

gauges.

6/ Repeat until approximately ¾ of the dip is removed.

7/ Leave for a few days and re-check. The cast iron will continue to move.

8/ Repeat until the dip is removed.

Troubleshooting

Poor cut.

1/ Dull blade. Change the blade.

2/ Bent tooth. Change the blade.

3/ Wrong type of blade for the job.

4/ Scoring not adjusted correctly. [If fitted]

Saw will not start.

1/ Check that the start switch is being depressed fully.

2/ Check that the electrical power cord is plugged into the power outlet.

3/ Check that the electrical supply is on [reset the breaker].

4/ With the power disconnected from the machine, check the wiring in the plug is correct.

Check that the rubber insulation is stripped enough, and is not causing a bad connection.

Check that all the screws are tight.

5/ With the power disconnected from the machine, check the wiring to the machine is

correct. Check that the rubber insulation is stripped enough and is not causing a bad

connection. Check that all the screws are tight

6/ Check that you have the correct power 220V not 110V

7/ Check the ground wire is wired correctly

The machine will not stop.

This is a very rare occurrence as the machine is designed to fail-safe. If it should occur

and you cannot fix the fault, seek professional assistance. The machine must be

disconnected from the power, and never run until the fault has been rectified.

1/ Stop switch faulty. Replace the stop switch.

2/ Internal contactor faulty. Replace the contactor.

43

Motor tries to start but will not turn.

1/ With the power disconnected from the machine. Try to turn the blade by hand. If the

blade will not turn check the reason for the jamming. Typical reasons is wood jamming

the blade.

2/ Capacitor faulty. Replace the capacitor.

3/ Motor faulty. Replace the motor.

Motor overheats.

The motor is designed to run very hot, but should it overheat it has an internal terminal

overload protector, that, will shut it down until the motor has cooled down, and then it

will reset automatically. If the motor overheats wait until it has cooled down, and restart.

If the motor keeps shuts down, check for the reason. Typical reasons are dull blade,

overfeeding the wood, motor cooling fan clogged or faulty, motor cooling fins clogged

and excessive ambient temperature.

Squeaking noise.

1/ Check that the motor cooling fan is not contacting the fan cover.

2/ Check the bearings.

3/ Check the drive belt.

Blade slows down during a cut.

1/ Loose drive belt. Re-tension the belt.

2/ Dull blade. Replace the blade or have it re sharpened.

3/ Feeding the wood too fast. Slow down the feed rate.

4/ Insufficient set on the teeth [wood nipping the blade]. Change blade for a blade with

the correct set.

5/ Oil or dirt on the drive belt. Clean or replace the drive belts.

6/ Fence not aligned correctly. Align fence.

Blade overheats.

1/ Dull blade. Change the blade or re sharpen the blade.

2/ Pitch is too small for the depth of cut. Change to a blade with the correct pitch.

4/ Wood too hard for the selected blade. Change the blade.

Machine vibrates.

1/ Machine not level on the floor. Re-level the machine, ensuring that it has no

movement.

2/ Damaged drive belt. Replace both belts.

Poor dust collection.

1/ Check the capacity of the dust collection system. You need a minim of 1000 cubic feet

per minute at the machine. The stronger the dust collection the better.

2/ Check the dust hose is not blocked.

3/ Check that the dust collector is not full.

44

Causes of the blade dulling.

1/ Wrong blade for the job.

2/ Over feeding the job.

3/ Cutting painted wood or abrasive material.

Accessories

The following accessories are available from Laguna Tools.

Miter gage.

Mobility kit.

Side extension tables for the TSS.

Flip stops for the TSS miter fence.

Throat plate inserts for TSS and TS.

Saw blades

Scoring blades.

Scoring unit.

Sliding table.

Side flip stops for TSS sliding table.

TSS sliding table clamp.

Work benches.

45

Electrical circuit

46

A1 A2

1L1 3L2 5L3

2T1 4T2 6T3

L1 L2 GND

POWER FROM WALL

Contactor

2

2

2

2

40

40

40

40

4 4

44

42

422

0

19

19

20

43

42

42

(Off-red)

PE

(On-green)

Yel/G

ree

n

Red

Red

Red

Red

Red

Bla

ck

Bla

ck

Red

Bla

ck

Bla

ck

Red

Bla

ck

Yel/Green

40A

Red

PE

44 43

47

A1 A2

1L1 3L2 5L3

2T1 4T2 6T3

L1 L2 GND

POWER FROM WALL

Contactor

Switch

2

2

2

2

40

40

40

40

4 4

44

42

422

0

19

19

24

2025

43

43

42

44

42

1

3

2

4

(Off-red)

19

2019

20

24

25

43 43

44

PE

(On-green)

Yel/G

ree

n

Yel/G

ree

n

Red

Red

Red

Red

Red

Red

Bla

ck

Bla

ck

Red

Black

Black Black

Bla

ck

Bla

ck

Red

Bla

ck

Yel/Green

Yel/Green

Black

Black

Black

Black

40A

Red

44

PE

PE

PE

Electrical diagram

with scoring

48

Parts breakdown for the TSS and TS table saws.

Note. Some parts shown in this manual may vary with the parts delivered with your

machine. We are constantly up grading the design of the machine and reserve the

right to change the machine and / or the specification with out notice.

Ordering spare-parts

When ordering spare parts specify:

Machine Model and serial number.

Part number required, taken from the exploded view drawing on the following page.

Quantity required

EXAMPLE: TO ORDER. Scoring electrical motor

Model :TSS

Serial number 12345

Description: Scoring electrical motor.

Part number: T80-2

Quantity: 1 piece

49

BODY WITH PANEL AND REMOVABLE PANEL [TS]

50

BODY WITH PANEL AND REMOVABLE PANEL [TS]

1 ST-01.01.01.00.00 BODY 1 2 PS.00.00.09 SAFETY DEVICE 1 3 DIN 985 NUT М12 DIN 4 4 206-83 PULLEY АМ12 4 5 DIN 985 NUT М8 DIN 4 6 UN 732 PULLEY Ф9ХФ35Ф2,5 4 7 1234-85 BOLT М8Х25 2 8 PS.00.00.03 STUD M12 2 9 2171-83 SCREW М10Х30 2 10 206-83 PULLEY АМ10 6 11 2171-83 SCREW М10Х25 4 12 833-82 SPRING PULLEY 10Н 4 13 GN6336-4-SK-40-M8-30 HANDLE М8Х30 2 14 206-83 PULLEY АМ8 2 15 DIN 914 STOP SCREW М8Х10 8 16 PS.00.02.03 INSERT 1 17 PS.00.02.01 PAD 1 18 PS.00.00.01 REMOVABLE PANEL 1 19 ST-01.01.00.00.02 PANEL 1

51

BODY WITH PANEL [TSS]

52

BODY WITH PANEL [TSS]

1 ST01.01.01.00.00 BODY 1

2 DIN 912 SCREW М10X45 4

3 BDS 833-82 SPRING PULLEY 10Н 4

4 BDS 206-78 PULLEY АМ10 4

5 ST01.01.00.00.13 BOLT 4

6 ST01.01.00.00.14 STUD 1

7 BDS 744-83 NUT М10 1

8 UN732 PULLEY Ф35ХФ10Х2.5 2

9 ST01-01.00.00.02 PANEL 1

10 ISO 7380 SCREW М6Х16 11

11 BDS 833-82 SPRING PULLEY 6Н 8

12 BDS 206-78 PULLEY АМ 6 8

13 MF1270.00.01.01.03 PLATE 1

14 MF1270.00.01.01.01 PAD 1

15 DIN 913 STOP SCREW М 8Х16 2

16 ISO 7380 SCREW М6Х25 2

17 MF1270.00.01.01.02 PLATE 1

18 DIN 913 STOP SCREW М 8Х10 6

19 MF1270.00.01.02.00 INSERT 1

MF1270.00.01.03.00 INSERT - DADO 1

53

LNR 460.00.00.00 Crosscut fence [Optional 18” long]

1 LNR 230.00.00.07 Rotating body 1 2 LNR 230.00.09.03 Special nut 1 5 LNR 230.00.00.04 Pin 1 7 BDS 206-83 Pulley АМ8 1 9 LNR 230.00.09.01 Strap 1 10 LNR 230.00.00.03 Narrow 1 11 BDS 832-83 Screw М4Х12 1 12 BDS 833-82 Spring pulley 4N 1 13 BDS 206-83 Pulley АМ4 1 14 DIN 7991 8.8 Screw М6Х8 1

15 DM5 321.05П.00.01 Axis 1

16 GN603-63-M8-25-DGN Handle М8Х25 1

17 LNR 460.00.00.14 Fence 1 18 BDS 2171-83 Screw М8Х25 2 19 BDS 833-82 Spring pulley 2-8Н 2 20 DIN 913 45H Screw М6Х25 1 21 LNR 230.00.00.13 Cotter 2 22 LNR 230.00.00.10 Scale 1

54

LNR 230.00.00.00 Crosscut fence [Optional 9” long]

1 LNR 230.00.00.07 Rotating body 1 2 LNR 230.00.09.03 Special nut 1 5 LNR 230.00.00.04 Pin 1 7 BDS 206-83 Pulley АМ8 1 9 LNR 230.00.09.01 Strip 1 10 LNR 230.00.00.03 Arrow 1 11 BDS 832-83 Screw М4Х12 1 12 BDS 833-82 Spring pulley 4N 1 13 BDS 206-83 Pulley АМ4 1 14 DIN 7991 8.8 Screw М6Х8 1

15 DM5 321.05П.00.01 Axis 1

16 GN603-63-M8-25-DGN Handle М8Х25 1

17 LNR 230.00.00.14 Fence 1 18 BDS 2171-83 Screw М8Х25 2 19 BDS 833-82 Spring pulley 2-8N 2 20 DIN 913 45H Screw М6Х25 1 21 LNR 230.00.00.13 Cotter 2 22 LNR 230.00.00.10 Scale 1

55

34

36

37

38

LU.00.00.00 Rip fence [TS]

56

LU.00.00.00 Rip fence [TS]

1 LU.00.00.09 GUIDE PIPE 1 2 LU.00.00.07 CARRYING SQUARE 1 3 BDS 1234-85 BOLT М6Х14 7 4 DIN 965A SCREW М6Х25 4

5 LU.00.00.01 REAR CARRYING SQUARE 1

6 BDS 744-83 NUT М6 9 7 BDS 206-83 WASHER АМ6 17 8 DIN 965A SCREW М6Х35 6 9 BDS 206-83 WASHER АМ8 17 10 BDS 744-83 NUT М8 6 11 BDS 1234-83 BOLT М8Х20 4 12 BDS 1234-83 BOLT М8Х35 6 13 LU.00.00.10 RULE 0-53" (T 443) 1 14 LU.11.01.00 FENCE BODY 1 15 LU.11.00.08 TIGHTEN ARM 1 16 LU.11.00.12 ECCENTRIC 1 17 LU.11.00.17 STUD 1 18 LU.11.00.13 ECCENTRIC WASHER 1 19 DIN 603 SCREW М8Х45 1 20 DIN 985 NUT М8 1 21 BDS 1234-85 BOLT М6Х40 1

22 GN719-38-M12 HANDLE 1

23 DIN 1481 SPRING PIN Ф4Х20 1 24 LU.11.00.02 LAMINATED FENCE 2 25 LU.11.00.07 SPRING 1 26 LU.11.05.00 POINTER 1 27 ISO 7380 SCREW М6Х10 2 29 DIN 985 NUT М6 17 33 DIN 603 SCREW М6Х20 16 34 DIN 1483 SPRING PIN Ф5Х30 1

35 LU.00.00.15 SIGN LAGUNA TS (T467) 1

36 DIN 913 STOP SCREW M8X10 2 37 LU.11.01.07 PAD S=1 MM 4 38 LU.11.01.11 PAD S=3 MM 1

57

34

35

33

36

LUMF.00.00.00 Sliding table rip fence [TSS]

58

LUMF.00.00.00 Sliding table rip fence [TSS]

1 LUMF.00.00.09 GUIDE PIPE 1 2 LUMF.00.00.07 CARRYING SQUARE 1 3 BDS 1230-85 BOLT М6Х14 6 4 DIN 965A SCREW М6Х25 4 5 LUMF.00.00.01 REAR CARRYING SQUARE 1 6 BDS 744-83 NUT М6 9 7 BDS 206-83 WASHER АМ6 16 8 DIN 965A SCREW М6Х35 6 9 BDS 206-83 WASHER АМ8 17 10 BDS 744-83 NUT М8 6 11 BDS 1234-83 BOLT М8Х20 4 12 BDS 1234-83 BOLT М8Х35 6 13 LU.00.00.10 RULE 0-53" (T 443) 1 14 LUMF.11.01.00 FENCE BODY 1 15 LU.11.00.08 TIGHTEN ARM 1 16 LU.11.00.12 ECCENTRIC 1 17 LU.11.00.17 STUD 1 18 LU.11.00.13 ECCENTRIC WASHER 1 19 DIN 603 SCREW М8Х45 1 20 DIN 985 NUT М8 1 21 BDS 1234-85 BOLT М6Х40 1 22 DIN 985 NUT M6 17 23 DIN 913 STOP SCREW M8X10 2 24 GN719-38-M12 HANDLE 1 25 DIN 1481 SPRING PIN Ф4Х20 1 27 LU.11.05.00 POINTER 1 28 ISO 7380 SCREW М6Х10 2 29 LU.11.00.07 SPRING 1 30 LU.11.00.02 LAMINATED FENCE 2 32 DIN 603 SCREW М6Х20 16 33 LUMF.00.00.15 SIGN LAGUNA TSS (T 535) 1 34 DIN 1483 SPRING PIN Ф5Х30 1 35 LU.11.01.07 PAD S=1 MM 4 36 LU.11.01.11 PAD S=3 MM 1

59

LVC1219 – 00.00.00 CIRCULAR SAW MITER FENCE

[TSS 4’ LONG]

60


[TSS 4’ LONG]

1 LVC600-00.00.02 COTTER 1 2 LVC600-00.00.05 ARROW 1 3 UN 6404 SCREW М6Х6 2 4 LVC600-00.00.03 LAMINATED FABRIC PAD 1 5 LVC600-00.00.04 BASIS 1 6 DIN 912 8.8 SCREW М8Х16 2 7 DIN 134 PULLEY ø10,5 xø22 x 2,5 1 8 DIN 127B PULLEY 2-8H 2 9 GN603-78-M10-20-DGR HANDLE М10Х20 1 10 LVC600-00.00.28 SQUARED COTTER 2 11 LVC600.11.00.10 COLOMN 1 12 GN603-63-M8-30-DGR HANDLE М8Х30 2 13 LVF 00.11.00.12 BODY 1 14 LVF 00.11.02.00-01 ARM 1 15 LVF.00.11.01.00 SUPPORT 1 16 LVF 00.01.00.29 THRUST STRIP 1 17 LVF 00.01.00.31 WOODEN BLOCK 1 18 DIN 7380 SCREW М6Х16 2 19 DIN 551 STOP SCREW М4Х5 POLYAMIDE 1 20 LVF 00.11.00.04 GUIDE 1 21 S2300.10.00.00.03 ECCENTRIC 1 22 DM5-321.40.30.14 SPRING 1 23 BDS 2170-77 RING В18 1 24 LVF.00.11.00.10 AXIS 1 25 S2300.10.00.00.02 STUD 1 26 DIN319 KU-25-M8 BALL 25 1 27 Т480 RULLER 60-1300 D-L 1 28 LVC1219-00.00.26 STRIP /BAND/ 15x3, L=1219mm 1 29 LVC1219-00.00.01 PROFILE L=1219mm 1 30 DIN 6336-KU-50-M8 STAR HANDLE М8 1 31 S2300.13.00.00.19 SCREW 1 32 DIN 1481 PIN Ф4Х40 1 33 S2300.13.00.00.12 SPRING 1 34 DIN 912 SCREW М6Х16 2 35 S2300.13.00.00.13 STOP 1 36 S2300.13.00.00.11 STRIP 1 37 S2300.13.00.00.21 STRIP 1 39 S2300.13.00.00.17 STRIP 1 40 S2300.13.00.00.18 PULLEY 1 42 DIN 915 SCREW М8Х16 1

61


[OPTIONAL 2’LONG]

62


[OPTIONAL 2’ LONG]

1 LVC600-00.00.02 COTTER 1 2 LVC600-00.00.05 ARROW 1 3 UN 6404 SCREW М6Х6 2 4 LVC600-00.00.03 LAMINATED FABRIC PAD 1 5 LVC600-00.00.04 BASIS 1 6 DIN 912 8.8 SCREW М8Х16 2 7 DIN 134 PULLEY ø10,5 xø22 x 2,5 1 8 DIN 127B PULLEY 2-8H 2 9 GN603-78-M10-30-DGR HANDLE М10Х30 1 10 LVC600-00.00.28 SQUARED COTTER 2 11 LVC600.11.00.10 COLOMN 1 12 GN603-63-M8-20-DGR HANDLE М8Х20 2 13 LVF 00.11.00.12 BODY 1 14 LVF 00.11.02.00-01 ARM 1 15 LVF.00.11.01.00 SUPPORT 1 16 LVF 00.01.00.29 THRUST STRIP 1 17 LVF 00.01.00.31 WOODEN BLOCK 1 18 DIN 7380 SCREW М6Х16 2 19 DIN 551 STOP SCREW М4Х5 POLYAMIDE 1 20 LVF 00.11.00.04 GUIDE 1 21 S2300.10.00.00.03 ECCENTRIC 1 22 DM5-321.40.30.14 SPRING 1 23 BDS 2170-77 RING В18 1 24 LVF.00.11.00.10 AXIS 1 25 S2300.10.00.00.02 STUD 1 26 DIN319 KU-25-M8 BALL 25 1 27 Т480 RULLER 60-700 D-L 1 28 LVC600-00.00.26 STRIP /BAND/ 15x3, L=600 mm 1 29 LVC600-00.00.01 PROFILE L=600 mm 1 30 DIN6336-KU-50-M8 STAR HANDLE М8 1 31 S2300.13.00.00.19 SCREW 1 32 DIN 1481 PIN Ф4Х40 1 33 S2300.13.00.00.12 SPRING 1 34 DIN 912 SCREW М6Х16 2 35 S2300.13.00.00.13 STOP 1 36 S2300.13.00.00.11 STRIP 1 37 S2300.13.00.00.21 STRIP 1 39 S2300.13.00.00.17 STRIP 1 40 S2300.13.00.00.18 PULLEY 1 42 DIN 915 SCREW М8 Х 16 1

63

MF1270.03.00.00.00 SLIDING TABLE (MF) L=1270 [TSS]

64

MF1270.03.00.00.00 SLIDING TABLE (MF) L=1270 [TSS]

1 S1270.03.00.00.01 SLIDING TABLE MOVABLE PART 1 2 S1270.03.00.00.09 MOULDING 2 3 S1270.03.00.00.11 SLIDING TABLE IMMOVABLE PART 1 4 S1270.03.00.00.06 GUIDE 8 5 BDS 12620-75 DOWEL DS-3 (Ф8) 8 6 БДС 664-70 WOODEN SCREW 5Х45 8 7 S2300.09.02.01.00 SLIDING TABLE COVER 1 8 DIN 963A SCREW М4Х12 6 9 S2300.09.00.00.03-01 COVER 2 10 БДС 833-82 SPRING PULLEY 6Н 6 11 S2300.03.00.00.12 COTTER 2 12 БДС 2171-83 SCREW М6Х12 8 13 S2300.04.00.00.10 GUIDE LOCK PIN 1 14 S2300.04.00.00.11 LOCK RING 1 15 БДС 7947-85 О-RING Ф8,5Х1,5 1 16 S2300.04.00.00.02-01 LOCK PIN 1 17 S2300.07.00.00.03 COTTER 1 19 S2300.07.00.00.02 PULLEY Ф24ХФ8,5Х3 1 20 S2300.07.00.00.01 HANDLE 1 21 БДС 2171-83 SCREW М6Х16 2 22 DIN 985-6 NUT М12 DIN 985 4 23 БДС 833-82 SPRING PULLEY 10N 4 24 БДС 1234-83 BOLT М10Х25 4 25 БДС 1250-83 NUT М12 4 26 S2300.05.00.00.04 THRUST WASHER 8 27 S2300.05.00.00.03-01 STUD М12Х60 4 28 S2300.05.00.02 COTTER 4 29 S3200.05.00.00.02 THRUST STRIP 2 30 S2300.03.00.14.00 STOP 2 31 S3200.03.00.00.06 CLEANER-FOG LUBRICATOR 4 32 S1150.03.00.00.03 SEPARATOR 1 33 БДС 4885-82 SHOT Ф15,081 10 34 S2300.09.00.00.01-01 TOP SLIDING TABLE COVER 1 35 ST-01.01.00.00.02 PANEL 1 36 ISO 7380 SCREW М6Х12 2 37 БДС 206-83 PULLEY АМ6 2 38 DIN 913 STOP SCREW М6Х18 2 39 МФ1270.00.01.00.02

МФ1270.00.01.00.03 INSERT 1

40 МФ1270.00.01.00.01 PAD 1 41 ISO 7380 SCREW М6Х16 3 42 ISO 7380 SCREW М6Х30 2 43 DIN 913 STOP SCREW М6Х10 3

65

MUS.00.00.00 PLATE EXTENSION TABLE

ОК.00.00.00 SUPPORT LEG

[TSS &TS]

1 ST-01.01.00.00.02 PANEL 1

2 BDS 206-83 PULLEY АМ12 2 3 BDS 1234-85 BOLT М12Х30 2 4 MUS.01.00.00 EXTENSION TABLE 800X900 1 5 DIN 913 STOP SCREW М6Х16 2 6 ОК.00.00 SUPPORT LEG 2 6 ОК.00.00 LEG 2 7 К34885 THRUST М8Х50 2

66

RC.00.00.00-T Scoring / [OPTIONAL TSS &TS]

4445

67

RC.00.00.00-T Scoring unit [OPTIONAL TSS & TS]

1 RC.00.00.12 NUT 1 2 RC.00.00.11 PRESSING PULLEY 1 3* OPTIONAL CIRCULAR SAW 120 Х 20 Х 2,5 1 4 RC.00.00.07 ARBOR 1 5 BDS 3389-83 STUD 1-6Х6Х16 1 6 BEARING 6004-2RS. C3 2 7 RC.00.00.06 BUSHING 1 8 BDS 2171-83 SCREW М10Х25 1 9 RC.00.00.15 AXLE BOX 1 10 BDS 1234-85 BOLT М8Х25 3 11 BDS 744-83 NUT М8 1 12 S2300.28.00.00.16 PIN 1 13 RC.00.00.38 ROLLER 1 14 BDS 2170-77 LOCK RING В10 1 15 BDS 2170-77 LOCK RING А42 2 16 ADJUSTING PULLEY Ф41ХФ34,5Х0,35 1 17 RC.00.00.16-01 SCREW-LIFTING 1 18 RC.00.00.36 LIFTING BLOCK 1 19 BDS 2171-83 SCREW М8Х25 2 20 S2300.28.00.00.20 BELT PULLEY 1 21 S2300.28.00.00.19 PULLEY 1 22 RC.00.00.17 SPRING 1 23 DIN 7991 SCREW М8 Х 20 1 24 RC.00.00.01 MOTOR AXIS 1 25 Т 80А-2 MOTOR 1 27 BDS 206-83 WASHER АМ8 2 28 RC.00.00.25 BELT PULLEY /RIGGER/ 1 29 RC.00.00.34 PULLEY 1 30 DIN 7991 SCREW М6Х16 1 31 RC.00.00.40 STUD 1 32 Flat belt 1.25Х20, L=510mm 1 33 BDS 2171-83 SCREW М8Х16 1 34 RC.00.00.04 LIMITING WASHER 1 35 RC.00.00.05 AXIS 1 36 DIN 7349 PULLEY Ф17 ХФ40 Х6 1 37 DIN 985 NUT М16 1 38 RC.00.00.19 GUIDE 1 39 RC.00.00.23 SPECIAL NUT 1 40 BDS 2170-77 LOCK RING В22 1 41 ADM410.20.00.106 SPRING 1 42 BDS 833-82 SPRING PULLEY 2-8H 5 43 RC.00.00.18 SCREW-MOVING 1 44 BDS 206-83 WASHER AM10 1 45 DIN 985 NUT М10 1

68

RCD 00.00.00 Scoring unit with DADO

[OPTIONAL TSS &TS]

69

RCD 00.00.00 Scoring unit with DADO [OPTIONAL TSS &TS]

Pos. Description Name

Quan

tity

1. RC 00.00.12 Nut 1

2. RC 00.00.11 Pressing pulley 1

3.* Circular disk ø120 x ø20 x 2 1

4. RCD 00.00.04 Support 1

5. DIN 1481 Spring pin ø5 x 18 3

6. RCD 00.00.06 Shaft 1

7. DIN6885 A Feather 1-6x6x16 1

8. RCD 00.00.08 Guiding axis 1

9. S3200.28.00.00.16 Pin 1

10. DIN 985 Nut M16 1

11. DIN 7349 Pulley M16 1

12. RCD 00.00.12 Guide 1

13. S400-28.00.00.52 Small insertion 1

14. Leveling pulley 40 9

15. DIN988 Pulley ø30x ø42 x 1 1

16. S400-28.00.00.53 Big insertion 1

17. S2300.28.00.02.00 Handle 2

18. S3200.28.00.00.19 Cover 1

19. S3200.28.00.36 Worm- wheel 1

20. S2300.28.00.00.08-01 Worm 1

21. S3200.28.00.00.20 Corpus 1

22. DIN134 Pulley M8 3

23. DIN 985 Nut M8 1

24. BDS833-82 Pulley PR 2-6N 3

25. DIN 912 Screw M 6x35 3

26. DIN134 Pulley M12 1

27. DIN 985 Nut M12 1

28. BDS 7947-85 O- Ring ø16x2 1

29. RC 00.00.40 Stud 1

30. RC 00.00.01 Motor axis 1

31. BDS833-82 Pulley PR 2-8N 4

32. BDS1234-85 Bolt M 8x25 2

33. Motor 1

34. RC 00.00.17 Spring 1

70

35. RC 00.00.25 Belt pulley 1

36. RC 00.00.34 Pulley 1

37. BDS1359-83 Screw M 5x16 1

38. DIN 7991 Screw M 8x20 1

39. Belt 20 х 1, L=510 1

40. S2300.28.00.00.19 Pulley 1

41. S2300.28.00.00.20 Belt pulley 1

42. DIN 471 Ring for shaft ø12 1

43. DIN 985 Nut M10 1

44. BDS2171-83 Screw M 8x25 3

45. RC 00.00.36 Lifting block 1

46. RCD 00.00.46 Lifting Screw 1

47. RC 00.00.38 Roller 1

48. RCD 00.00.48 Axle 1

49. BDS744-83 Nut M8 1

50. RCD 00.00.50 Buch 1

51. DIN 472 Ring for opening ø42 2

52. Bearing 6004.2RS.C3 2

53.* RCD 00.60.04 Spacer 3/8" 1

54.* RCD 00.60.03 Spacer 1/4" 1

55.* RCD 00.60.02 Spacer 1/8" 1

56.* RCD 00.60.01 Spacer 1/16" 1

* - By special request

71

SF 250M.08.00.00.00 BRACKET TABLE [TSS &TS]

1 SF250M.08.00.00.01 SLIDE BLOCK 1


3 GN603-73-M10-20DGR HANDLE 2

4 SF2300.15.01.00.00 EXTENSION TABLE 500Х320 1

5 BDS 1362-83 STOP SCREW М6Х16 2

72

108

108

108

89

88

24

86

49

ST01-02.00.00.00 MAIN CIRCULAR SAW / 1-PHASE MOTOR 2,2kW

[TSS & TSS]

73

ST01-02.00.00.00 MAIN CIRCULAR SAW / 1-PHASE MOTOR 2,2kW /

1 GN6336.4-ST-40-M8-40 HANDLE М8Х40 2 2 KRMC-ST 11.01 SMALL HAND WHEEL FOR FOLDING

HANDLE 1

3 GN 698.3-26-М6 FLYWHEEL HANDLE, BLACK 1

4 GN 698-KT-26-M10 FLYWHEEL HANDLE, BLACK 1

5 DIN7991 SCREW М6Х12 1

6 БДС 832-83 SCREW М4Х10 4

7 БДС 833-82 PULLEY 2-4Н 4

8 БДС 206-83 PULLEY АМ4 4

9 S2300.02.00.00.23 SPRING 2

10 AS 2035 AXIAL PULLEY 20Х35Х1 4

11 ST 01-02.00.00.88 BUSHING – TILTING 1

12 CRMSH 11.07 PIN Ф8Х32 2

13 ST 01-02.00.00.87 ARBOR – TILTING 1

14 ST 01-02.00.35.00 SAFETY DEVICE 1


16 DIN 913 STOP SCREW М8Х8 6

17 BDS 833-82 PULLEY 2-8Н 29

18 BDS 2171-83 SCREW М8Х25 11

19 DIN 913 STOP SCREW М6Х20 6

20 ST 01-02.00.00.50 THRUST RING 1

21 ST 01-02.00.00.89 BASIS FOR TILTING 1

22 BDS 2171-83 SCREW М8Х20 10

23 DIN 1481 PIN Ф5Х26 2

24 BDS 744-83 NUT М8 3

25 DIN 7991 SCREW М8Х16 5

26 ST 01-02.00.00.76 STOP 90º 1

27 ST 01-02.00.00.90 TILTING SECTOR 1

28 ST 01-02.00.00.32 SECTOR 2

29 DIN 1481 PIN Ф5Х20 4

30 ST 01-02.00.00.79 STOP 45º 1

31 DIN 933 8.8 BOLT М8Х25 8

32 KRM-ST11.01 SMALL HAND WHEEL 1

33 ST 01-02.00.24.00 ARROW 1

34 ST 01-02.00.00.22 ARBOR LIFTING 1

35 ST 01-02.00.00.16 BUSHING 3

36 ST 01-02.00.00.34 THRUST STRIP 1

37 BDS 744-83 NUT М6 1

38 BDS 1234-85 BOLT М6Х40 1

39 ST 01-02.00.00.46 STOP SCREW 1

40 DIN 7991 8.8 SCREW М10Х25 1

41 ST 01-02.00.00.44 PULLEY Ф10,5 Х Ф25Х8 1

42 ST 01-02.00.00.02 CRADLE 1

43 ST 01-02.00.00.42 THRUST BLOCK 1

44 ST 01-02.00.00.69 WORM TILTING 1

45 ST 01-02.00.00.03 SECTOR LIFTING 1

46 BDS 1234-85 BOLT М10Х40 1

47 ST 01-02.00.00.41 SPECIAL BOLT 1

48 ST 01-02.00.00.40 BLOCK 1

74

49 BDS 744-83 NUT М10 2

50 ST 01-02.00.00.58 COLOMN 1

51 ST 01-02.00.59.00-02 MOTOR CRADLE / ESR 90L / 1

52 DIN 7349 PULLEY ø17 X ø 40 X 6 1

53 DIN 985 NUT М16 1

54 MOTOR 1

55 ST 01-02.00.00.63 BELT PULLEY 1

56 BELT SPZ 630 MN, Lp≈Ld≈Lw= 630mm 2

57 S2300.02.00.00.43 PULLEY Ф40ХФ24Х4 1

58 DIN 985 NUT М12 1

59 S2300.02.00.00.17 PULLEY 1

60 AS 1528 AXIAL PULLEY 15Х28Х1 3

61 S2300.02.00.00.08 BASIS LIFTING 1

62 S2300.02.00.00.09 BLOCK LIFTING 1

63 S2300.02.00.00.65 SHORT SEAL 1

64 S2300.02.00.86.00 ASPIRATING SHOE 1

65 DIN 7337A RIVET Ф4Х8 ST/ST 8

66 S2300.02.00.00.81 STOP 1

67 S2300.02.00.00.01 BEAM 1

68 S2300.02.00.00.80 PANTOGRAPH STRAP 1


70 S2300.02.00.00.66 SEALING 1

71 S2300.02.00.37.00 MAIN CIRCULAR SAW 1

72 S2300.02.00.00.52 COTTER 1

73 S2300.02.00.37.18 CARRIER 1

74 S2300.02.00.00.53 BACK STRAP 1

75 S2300.02.00.00.57 PIN 2

76 S2300.02.00.00.56 MIDDLE STRAP 1

77 S2300.02.00.00.38 RIVING KNIFE 1

78 S2300.02.00.00.55 FRONT STRAP 1

79 DIN 7991 SCREW М10Х52 1

80 S2300.02.00.68.00 VALVE 1

81 S2300.02.00.00.60 STABILIZE STRAP 1

82 S2300.02.00.23.00 GUIDE LIFTING 1

83 S2300.02.00.36.00 HANDLE WITH A BALL 1

84 DIN 985 NUT М8 1

85 ASPIRATING HOSE, L=1200mm 1

86 S2300.02.00.00.14 WORM LIFTING 1

87 BDS 2171-83 SCREW М8х30 2

88 DIN 933 8.8 BOLT M8X30 1

89 DIN 913 8.8 STOP SCREW M8X30 2

90 S2300.02.37.00.01 NUT 1

91* SAW BLADE ø12” 2

92 S2300.02.37.02.00 FLANGE EXTERIOR 1

93 S2300.02.37.00.04 STOP 1

94 DIN 1481 SPRING PIN Ф5Х20 2

95 S2300.02.37.06.00 ARBOR WITH FLANGE 1

96 BEARING 6205 2RS.С3 2

97 BDS 2170-77 LOCK RING А52 2

98 S2300.02.37.00.17 BUSHING REMOTE 1

75

99 BDS 2170-77 RING В70 1

100 S2300.02.37.00.08 THRUST RING 1


102 S2300.02.37.00.10 CARRIER 1

103 S2300.02.37.00.13 BELT PULLEY 1

104 UN 732 PULLEY ø8 х ø35 х 2,5 1

105 BDS 833-82 PULLEY 2-8Н 1

106 BDS 2171-83 SCREW М8Х20 1

107 BDS 3389-83 COTTER 8Х7Х20 1

108 DIN 988 PULLEY ø20 х ø28 х 1 3

- by order

ST01-10.00.00 HOLD DOWN CLAMP

76

[OPTIONAL TSS]

1 ST 01-10.00.03 COTTER 1

2 ST 01.10.00.04 PAD 1

3 ST 01-10.00.05 THRUST 1

4 LVC 600-00.00.10 COLOMN 1

5 LVF 00.11.00.12 BODY 1

7 GN603-63-M8-20-DGR HANDLE М8Х20 2

8 LVF.00.11.01.00 SUPPORT 1

9 LVF 00.11.02.00-01 LEVER 1

10 LVF 00.11.00.04 GUIDE 1

11 DM5-321.40.30.14 SPRING 1

12 BDS 2170-77 RING В18 1

13 LVF.00.11.00.10 AXIS 1

14 S2300.10.00.00.03 ECCENTRIC 1

15 S2300.10.00.00.02 STUD 1

16 DIN319-KU-25-M8-C BALL 25 1

77

U – 00.00.00 Stop 90° [TSS]

1. U-00.00.01 THRUST BOLT 1

2. BDS 744-83 NUT-М8 2

3. DIN 913 SCREW М8Х12 1

4. DIN 915 SCREW М8Х16 1

5. У-00.04.00 BASIS 1

6. BDS1230-85 BOLT М8Х30 1

7. У-00.00.02 STRAP 1

MTS000010%3ATS+TSS+Tablesaw+w%2Fo+Scoring+

Documents

Transcript of MTS000010%3ATS+TSS+Tablesaw+w%2Fo+Scoring+