MOSHELL COMMANDSNOTE: Exclusive for PENTA PROJECT TEAM/Author/RMALVAREZ 1. To read MCPA tempCabx (to check RBS status)lhsh 010200/port_0_dev_13 mcpaBoard templhsh 010200/port_0_dev_13 helplhsh 010200/port_0_dev_13 restart (if need to restart)TELNET commands should MOSHELL hang due to GPBtelnet IP addcv cucv lscv mkcv setrestartObj me2. To check E1-MS port in RXI/RBS (add E1 for RBS)In RNCst get iub -> look for RBS IDIn RXIpr . eg. pr .0095lk st atmport=ms-x-ybllget ms-2-2 (then check iub number with STR printout see tally or not)reservedBy Aal2PathVccTp=b0001a2 get radiolink num> wait 2> done9. To enable E1 supervisionset10. To create Group (eg. Not reserved VclTp)get vcltp reservedby !.*=lma vcltp reservedby !.*=11. To create performance counterspst12. To check cell stateIn RBSlst cellget radiolinks (to see how many line/s being used)13. To check RBS MOIn RBSst plug (AuxPlugInUnit=2 is the RET, AuxPlugInUnit=1 is the ASC)cabxcab (without the external parts)14. To change SAC (Service Area Code)In RBS determine max capability to transmitSUNWMU> get all xdlget all xdl ---> in EMAS, click RBSLocalCell, Properties,Characteristics, Max & Min valueexample result printout = maxDlPowerCapability 42215. To lock/unlock cellsIn RNCst utrancell=sunwmulst sunwlbl sunw (to lock cell & channels)bl sunw (to lock cell only)deb sunw (to unlock)16. To check RBS infoIn RBSGet 0Get 1 (check ntpServerAddressPrimary)17. To check network clock synchronisationIn RNC & RBSRead clock (GMT +8)ntpconfig infoCheck which OMNIFSERVER the node is connected to (i.entpServerAddressPrimary) from get 118. To check atmport & pp (physical port)In RBSlpr atmportvc32&33 for signalinglpget 1007 (vc proxy) to see number of ATM traffic cells transferredget atmport=1-2-2then : lget Subrack=1,Slot=2,PlugInUnit=1,Etm1=1,E1PhysPathTerm=pp2to un/lock have to set values 1 or 019. To administer state of MosIn RBSSt plugDeb proxyBl proxyNo need to use set 1 or set 0 (only for physical ports) otherwise use deb & bl20. To autocreateCVIn RNC & RBSGet configCv ls (2 CVs will be used for the autocreate CV function)Set proxy autoCreatedCVIsTurnedOn true/falseSet timeForAutoCreatedCV (UTC time)Set timeForAutoCreatedCV 13:00 (cv autocreated at 9pm)21. To restart NodeIn RNC,RXI & RBSacc 0 restartpoll (to wait 20seconds until node comes up again)22. To create CVIn RNC,RXI & RBScvms CXP9010373%1_R11G_050725_1516 emfauzi change_ntpserver_ipcvms CXP9010373%1_R11G_050725_1516 followed by comments for the CVcvset CXP9010373%1_R11G -- to set the CV startable23. To restart nodeIn RNC & node Bacc 0 restartpol - to get moshell connected once node has restarted24. To check plugin statusIn RNC & node Bst pluginst plugin 1 0st plugin 0 1lst plug 025. To enter Moshell with security enabledIn RNC & node Bmoshell -c host.p12 10.78.37.22526. To block sectors via MoshellIn RNCSt blipBl the proxyDeb the proxy (can have multiple proxies for more cells)27. To view delay & attenuation parameters within a sectorIn RBSGet jumperGet feederGet rbs xdl28. To delete something already done with a scriptIn RNC/RXI/RBSFirst you have to generate the MO Delete scriptThis is done by ./undomo add2nde1inrxi_PUJMMU.mo > pujmrxibesi01.mo[~]$ ./undomo add2nde1inrxi_PUJMMU.mo > pujmrxibesi01.mo[~]$Where add2nde1inrxi_PUJMMU.mo is the script which was run earlierAnd pujmrxibesi01.mo is the Delete ScriptModify add2nde1inrxi_PUJMMU.mo so that downtime will be lessRun pujmrxibesi01.mo to undo the wrongly defined MOThen run the modified/correct add2nde1inrxi_PUJMMU.mo29. To check E1 stateIn RBSSt atmportCheck port lock stateSt pp St pp2 st pp3 st pp430. To check locked board in nodeIn all nodeslst plug 031. To restart / reload boardIn all nodesAcc 000900 restart Acc 001400 reload32. run and trunIn all nodestrun is only for xml scriptsrun for scripts such as set DAGAMU_1 usedFreqThresh2dEcno -12trun for running the last script : rbs_EQINMU_site_complete.morun is for any script (txt for example)open logfile l+ 20060113_CR003_RNCTGEM01.logcannot have undo mode while having gsg activatedrun CR003_13012006.txtclose logfile33. CAB printoutIn all nodesRXIKPNG02> cab060206-11:09:22.......=====================================================================================================SMN APN BOARD GREEN YELLOW RED PRODUCT NRREV DATE SERIAL NR TEMP COREMGR=====================================================================================================0 1 SCB2 ON OFF OFF ROJ 119 2108/3 R3D 20050608 TU863644890 2 HUB MP ON OFF OFF ROJ 119 2106/40 R5A 20050626 TU86494707 +32C Active0 3 GPB40 ON OFF OFF ROJ 119 2106/40 R5A 20050626 TU86494699 +31C StandbyReady0 4 TUB ON OFF OFF ROJ 119 2104/4 R3B 20050620 TU864424360 5 TUB ON OFF OFF ROJ 119 2104/4 R3B 20050620 TU864424390 8 ET-MC41 ON OFF OFF ROJ 119 2161/1 R3C 20050718 TU866441460 10 ET-MC41 ON OFF OFF ROJ 119 2161/1 R3C 20050718 TU866440420 12 ET-MC41 ON OFF OFF ROJ 119 2161/1 R3C 20050718 TU866440520 14 ET-MC41 ON OFF OFF ROJ 119 2161/1 R3C 20050718 TU866440560 16 ET-MC41 ON OFF OFF ROJ 119 2161/1 R3C 20050718 TU866440370 18 ET-MC41 ON OFF OFF ROJ 119 2161/1 R3C 20050718 TU866440670 20 ET-MC41 ON OFF OFF ROJ 119 2161/1 R3C 20050708 TU865928670 24 ET-M4 ON OFF OFF ROJ 119 2102/1 R3G 20050702 TU865459970 25 ET-M4 ON OFF OFF ROJ 119 2102/1 R3G 20050702 TU865459980 26 ET-M4 ON OFF OFF ROJ 119 2102/1 R3G 20050702 TU865459960 27 ET-M4 ON OFF OFF ROJ 119 2102/1 R3G 20050702 TU865460010 0 SCB2 ON OFF OFF ROJ 119 2108/3 R3D 20050608 TU86364157-----------------------------------------------------------------------------------------------------1 is slot 10 is slot 2834. When lock/unlock from logIn RBSLgvLgaevsm rather long35. Read VSWR / OUTPUT Power from RBSIn RBSlhsh 010900 ps port*lhsh 010600 lhsh port_0_dev_17 asc vswr - sector 1lhsh 010900 lhsh port_0_dev_19 asc vswrlhsh 010900 lhsh port_0_dev_19 asc vswr - sector 2lhsh 010600 lhsh port_0_dev_17 asc powacc 011200 restart - restart AIUport_0_dev_5 FU12port_1_dev_11 ASCSec.2-port_4_dev_6 RU21port_4_dev_6 FU12port_5_dev_13 ASCSec.3-port_8_dev_7 RU21port_8_dev_7 FU12port_9_dev_15 ASCSMN APN PORT BOARD GREEN YELLOWRED PRODUCT NR REV DATE SERIAL NR=================================================================================================================0 12 port_0_dev_4 RU22 steady 16hz offKRC 118 22/1 R1G 20070829 AE555209050 12 port_4_dev_5 RU22 steady 16hz off KRC 118 22/1 R1G 20070829 AE555208930 12 port_8_dev_6 RU22 steady 16hz off KRC 118 22/1 R1G 20070829 AE55520921----------------------------------------------------------------------------------------------------------------- 080408-13:32:58 10.109.246.153 7.0h RBS_NODE_MODEL_J_5_16 stopfile=/tmp/1052$ lhsh 001200/port_0_dev_4 fui get devstatBoard: fuHw: Hw08P1, faultStatus: 0x0, temp: 47.0, sv: on, svTmaDegrad:off, comp: onDev1: mode: {ModeAuxTma}, feedPow: highPowcapability: {vswrAntSv | tma19Sv | ulGainConf | maxUlGain}svCtrl: 0xe400, faultStatus: 0x0000txFreq: 882800, sensitivity: 49, gainUl: 4.0, volt: 16571.5,curr: 84.0, dCycle: 0.0Dev2: mode: {ModeAuxTma}, feedPow: highPowcapability: {resAntSv | tma19Sv | ulGainConf | maxUlGain}svCtrl: 0x2400, faultStatus: 0x0000txFreq: 0, sensitivity: 0, gainUl: 4.0, volt: 16565.9, curr:90.4, dCycle: 0.03 sectors sampleUSMLAP30> lhsh 001200/port_4_dev_5 fui get vswr080521-03:26:13 10.108.243.9 7.0t RBS_NODE_MODEL_J_5_16 stopfile=/tmp/5952$ lhsh 001200/port_4_dev_5 fui get vswrvswr: -0.7[dB] te disable bus_send bus_receive NBAPCheck status again$ te status NBAPpid name enabled groups- NBAP check error info interface objectIn node TeraTermUser = ericPw = ericssonMonitor 10.78.xx.xx54. To check commands sent in nodeIn node RNC, RBS, RXIhi55. To check external Open Door alarm in RBS is set to which probable causeIn node RBSPr almdeviceGet proxy (either 2 / 1 or 9)Usually 9 for RBS door and 2 for BBU doorSome put 1 for BBU doorGet proxy for parameter checkLock proxy to change probableCauseBl 54probableCause 522 -> power supplyprobableCause 118 -> enclosure_door_open_m3100set 54 probableCause 118then unlock back proxydeb 5456. To calibrate RET via moshellIn node RBSLpr retAcl proxy253Equipment=1,SectorAntenna=3,AuxPlugInUnit=2,RetuDeviceGroup=1,RetDeviceSet=1,RetDevice=1acc 267 forceCalibrationalarm will go away in 2 minutes approx