Moshell CMD

Title: Personal Guide to MOSHELL Date: Jul 01, 2007 Note: This document is not a troubleshooting guide. It is intended as a quick referenc

most commonly used command. Please consult higher level technical support whenever in doubt

__________________________________________________________________________ AetIworxDrvAtmProcIworxatm Alarm in ETMC41 board RNC/RXI/NodeBAiDevice_ExternalUnitFailure RBS3206ASC/RU/FU COMMANDS RBS3206ATM LAYER WHEN RBS CONNECT TO RXICarriers & Channels in nodeBCell IDCheck Feeder CurrentCheck LNA Transistors in ASCCheck PDR alarm In RNCCheck VC12 is used or notCheck VSWRCPU LOADDisk Usage And HDisk InfoDS0 BUNDLEFind RBS for this e1Find RNC/RXI port to the RBSGCP Signalling & It's associated Physical LinkHELPIMAGROUP Disabled E1/IMALINK are OKLOG - COMMAND, ALARM & EVENT LOGMGWNeighbour RelationNodeSynchTp ThresholdExceeded AlarmRAX CongestionRNC ModuleRET Not Calibrated - RBS3206Sector Disabled No Alarm In NodeBSector Disabled No Utrancell Alarm in RNCSector RejectSignalFromHardwareSOFTWARE ALLOC & WHICH BOARD IT's LOADEDSS7STDHTMADEVICE_AntennaSystemProblemTxDeviceGroup GeneralHwError RBS3206UE REGISTER COUNTUNIX CMDUTRANC/RACH/FACH/PCH Disabled & EMAS/MOSHELL is OK UNIX

/* Useful when unable to Moshell from Citrix. Remote login to master host server, & runfrom there */ UNIX_PROMPT> rlogin mashosts /* Find number of user session */ UNIX_PROMPT> finger /* Change Password */ UNIX_PROMPT> passwd /* Trace route to destination IP */ UNIX_PROMPT> traceroute <node_ID or IP> /* Print IP/DNS entry */ UNIX_PROMPT> ipconfig -a RNC MODULE Use Command STR or STRT to determine which RNC module a site is connected to RNC> str RNC> strt CELL ID RNC> lt ^utranc RNC> lget utrancell cid {list all Cid} RNC> lget utranc cid <cell_id> {to get site using this cid} RNC> lget <utrancell> cid {to get cid of utrancell} RBS> lt rbslocal RBS> lget rbslocalcell localcell 070603-12:49:44 10.230.8.13 7.0 RESTRICTED RBS_NODE_MODEL_H_6_6 stopfile=/tmp/18514 =======================================================================================MO Attribute Value =======================================================================================RbsLocalCell=S1C1 RbsLocalCellId S1C1 RbsLocalCell=S1C1 localCellId 15754 RbsLocalCell=S3C1 RbsLocalCellId S3C1 RbsLocalCell=S3C1 localCellId 15756 RbsLocalCell=S2C1 RbsLocalCellId S2C1 RbsLocalCell=S2C1 localCellId 15755 ======================================================================================= Check Packet Data Router Alarm in RNC 3RJ01> lt packet Load Proxys for MOs of following type... =================================================================================== PacketDataRouter =================================================================================== Please Confirm [y/n]: y Last MO: 2810. Loaded 10 MOs. Total: 2811 MOs. MO Class: PacketDataRouter. 3RJ01> lst packet 060923-17:24:34 172.30.204.32 6.1zr RNC_NODE_MODEL_F_5_2 stopfile=/tmp/12668 ===================================================================================

Proxy Adm State Op. State MO =================================================================================== 2801 0 (LOCKED) 1 (ENABLED) RncFunction=1,RncModule=8,PacketDataRouter=pdr5b 2802 1 (UNLOCKED) 1 (ENABLED) RncFunction=1,RncModule=8,PacketDataRouter=pdr5a 2803 0 (LOCKED) 1 (ENABLED) RncFunction=1,RncModule=8,PacketDataRouter=pdr4b 2804 1 (UNLOCKED) 1 (ENABLED) RncFunction=1,RncModule=8,PacketDataRouter=pdr4a 2805 0 (LOCKED) 1 (ENABLED) RncFunction=1,RncModule=1,PacketDataRouter=pdr3b 2806 1 (UNLOCKED) 1 (ENABLED) RncFunction=1,RncModule=1,PacketDataRouter=pdr3a 2807 0 (LOCKED) 1 (ENABLED) RncFunction=1,RncModule=1,PacketDataRouter=pdr2b 2808 1 (UNLOCKED) 1 (ENABLED) RncFunction=1,RncModule=1,PacketDataRouter=pdr2a 2809 0 (LOCKED) 1 (ENABLED) RncFunction=1,RncModule=1,PacketDataRouter=pdr1b 2810 0 (LOCKED) 0 (DISABLED) RncFunction=1,RncModule=1,PacketDataRouter=pdr1a =================================================================================== Total: 10 MOs 3RJ01> lt pdr Load Proxys for MOs of following type... =================================================================================== PdrDevice =================================================================================== Please Confirm [y/n]: y Last MO: 2815. Loaded 5 MOs. Total: 2816 MOs. MO Class: PdrDevice. 3RJ01> lst pdr 060923-17:25:06 172.30.204.32 6.1zr RNC_NODE_MODEL_F_5_2 stopfile=/tmp/12668 =================================================================================== Proxy Adm State Op. State MO =================================================================================== 2801 0 (LOCKED) 1 (ENABLED) RncFunction=1,RncModule=8,PacketDataRouter=pdr5b 2802 1 (UNLOCKED) 1 (ENABLED) RncFunction=1,RncModule=8,PacketDataRouter=pdr5a 2803 0 (LOCKED) 1 (ENABLED) RncFunction=1,RncModule=8,PacketDataRouter=pdr4b 2804 1 (UNLOCKED) 1 (ENABLED) RncFunction=1,RncModule=8,PacketDataRouter=pdr4a 2805 0 (LOCKED) 1 (ENABLED) RncFunction=1,RncModule=1,PacketDataRouter=pdr3b 2806 1 (UNLOCKED) 1 (ENABLED) RncFunction=1,RncModule=1,PacketDataRouter=pdr3a 2807 0 (LOCKED) 1 (ENABLED) RncFunction=1,RncModule=1,PacketDataRouter=pdr2b 2808 1 (UNLOCKED) 1 (ENABLED) RncFunction=1,RncModule=1,PacketDataRouter=pdr2a 2809 0 (LOCKED) 1 (ENABLED) RncFunction=1,RncModule=1,PacketDataRouter=pdr1b 2810 0 (LOCKED) 0 (DISABLED) RncFunction=1,RncModule=1,PacketDataRouter=pdr1a 2811 1 (UNLOCKED) 1 (ENABLED) Equipment=1,Subrack=MS,Slot=23,PlugInUnit=1,SpbDevicSpbDeviceSet=1,PdrDevice=1 2812 1 (UNLOCKED) 1 (ENABLED) Equipment=1,Subrack=MS,Slot=22,PlugInUnit=1,SpbDevicSpbDeviceSet=1,PdrDevice=1 2813 1 (UNLOCKED) 1 (ENABLED) Equipment=1,Subrack=MS,Slot=21,PlugInUnit=1,SpbDevicSpbDeviceSet=1,PdrDevice=1 2814 1 (UNLOCKED) 1 (ENABLED) Equipment=1,Subrack=MS,Slot=20,PlugInUnit=1,SpbDevicSpbDeviceSet=1,PdrDevice=1 2815 1 (UNLOCKED) 1 (ENABLED) Equipment=1,Subrack=MS,Slot=19,PlugInUnit=1,SpbDevicSpbDeviceSet=1,PdrDevice=1 =================================================================================== Total: 15 MOs 3RJ01> get 2815 060923-17:37:44 172.30.204.32 6.1zr RNC_NODE_MODEL_F_5_2 stopfile=/tmp/12668 =======================================================================================815 Equipment=1,Subrack=MS,Slot=19,PlugInUnit=1,SpbDeviceGroup=1,SpbDeviceSet========================================================================================PdrDeviceId 1 administrativeState 1 (UNLOCKED) availabilityStatus 0 (NO_STATUS) deviceIndId PDRD-1

operationalState 1 (ENABLED) reservedBy [2] = >>> reservedBy = RncFunction=1,RncModule=1,PacketDataRouter=pdr1b >>> reservedBy = RncFunction=1,RncModule=1,PacketDataRouter=pdr1a spmReference Subrack=MS,Slot=19,PlugInUnit=1,Spu=1,Spm=1 usageState 0 (IDLE) userLabel MS-19-1 =======================================================================================Total: 1 MOs RET Not Calibrated Alarm RBS3206 GNJ039> alt 060923-19:45:18 10.230.64.241 6.1zr RBS_NODE_MODEL_H_6_3 stopfile=/tmp/19709 Trying file=/home/ehassha/moshell_logfiles/logs_moshell/tempfiles/tmp19684_20060923-193939/ior19684 Resolving the alarm service in OMS... Simple Alarm Client initialized... Starting to retrieve active alarms Nr of active alarms are: 2 =======================================================================================Date & Time (Local) S Specific Problem Cause Mo-=======================================================================================2006-09-23 19:45:13 m RetDevice_RetNotCalibrated equipment_malfunction SectorAntenna=2,AuxPlugInUnit=2,RetuDeviceGroup=1,RetDeviceSet=1,RetDevice=1 2006-09-23 19:45:14 M RetDevice_TiltFailure equipment_malfunction SectorAntenna=2,AuxPlugInUnit=2,RetuDeviceGroup=1,RetDeviceSet=1,RetDevice=1 >>> Total: 2 Alarms (0 Critical, 1 Major) GNJ039> lt ret Load Proxys for MOs of following type... =================================================================================== RetDevice RetDeviceSet RetuDeviceGroup RetProfile =================================================================================== Please Confirm [y/n]: y Last MO: 33. Loaded 3 MOs. Total: 34 MOs. MO Class: RetDevice. Last MO: 36. Loaded 3 MOs. Total: 37 MOs. MO Class: RetDeviceSet. Last MO: 39. Loaded 3 MOs. Total: 37 MOs. MO Class: RetuDeviceGroup. Last MO: 55. Loaded 16 MOs. Total: 53 MOs. MO Class: RetProfile. GNJ039> lst ret 060923-19:46:01 10.230.64.241 6.1zr RBS_NODE_MODEL_H_6_3 stopfile=/tmp/19709 =================================================================================== Proxy Adm State Op. State MO =================================================================================== 31 1 (ENABLED) Equipment=1,SectorAntenna=3,AuxPlugInUnit=2,RetuDeviRetDeviceSet=1,RetDevice=1 32 0 (DISABLED) Equipment=1,SectorAntenna=2,AuxPlugInUnit=2,RetuDeviRetDeviceSet=1,RetDevice=1 33 1 (ENABLED) Equipment=1,SectorAntenna=1,AuxPlugInUnit=2,RetuDeviceGroup=1, RetDeviceSet=1,RetDevice=1 34 1 (ENABLED) Equipment=1,SectorAntenna=3,AuxPlugInUnit=2,RetuDeviceGroup=1, RetDeviceSe 35 0 (DISABLED) Equipment=1,SectorAntenna=2,AuxPlugInUnit=2,RetuDeviceGroup=1, RetDeviceSe 36 1 (ENABLED) Equipment=1,SectorAntenna=1,AuxPlugInUnit=2,RetuDeviceGroup=1, RetDeviceSe 37 1 (ENABLED) Equipment=1,SectorAntenna=3,AuxPlugInUnit=2,RetuDeviceGroup=1 38 0 (DISABLED) Equipment=1,SectorAntenna=2,AuxPlugInUnit=2,RetuDeviceGroup=1

39 1 (ENABLED) Equipment=1,SectorAntenna=1,AuxPlugInUnit=2,RetuDeviceGroup=1 =================================================================================== Total: 9 MOs GNJ039> actl ret 060923-19:46:10 10.230.64.241 6.1zr RBS_NODE_MODEL_H_6_3 stopfile=/tmp/19709 =======================================================================================Proxy MO Action Nr of Params =======================================================================================31 SectorAntenna=3,AuxPlugInUnit=2,RetuDeviceGroup=1,RetDeviceSet=1,RetDevice=1 forceCalibration 0 32 SectorAntenna=2,AuxPlugInUnit=2,RetuDeviceGroup=1,RetDeviceSet=1,RetDevice=1 forceCalibration 0 33 SectorAntenna=1,AuxPlugInUnit=2,RetuDeviceGroup=1,RetDeviceSet=1,RetDevice=1 forceCalibration 0 37 SectorAntenna=3,AuxPlugInUnit=2,RetuDeviceGroup=1 startHwTest 38 SectorAntenna=2,AuxPlugInUnit=2,RetuDeviceGroup=1 startHwTest 39 SectorAntenna=1,AuxPlugInUnit=2,RetuDeviceGroup=1 startHwTest

GNJ039> actc 32 forceCalibration 060923-19:46:47 10.230.64.241 6.1zr RBS_NODE_MODEL_H_6_3 stopfile=/tmp/19709 Call Action forcecalibration on following MOs ? =================================================================================== 32 Equipment=1,SectorAntenna=2,AuxPlugInUnit=2,RetuDeviceGroup=1,RetDeviceSet=1,Ret=================================================================================== Are you Sure [y/n] ? y =======================================================================================Proxy MO Action Nr of Params =======================================================================================32 SectorAntenna=2,AuxPlugInUnit=2,RetuDeviceGroup=1,RetDeviceSet=1,RetDevice=1 forceCalibration 0 >>> Return value = null =======================================================================================Total: 1 MOs attempted, 1 MOs actioned Check VSWR /* Note: VSWR < 1.5 */ RBS 3206 GNJ039> cabx 060923-20:14:10 10.230.64.241 6.1zr RBS_NODE_MODEL_H_6_3 stopfile=/tmp/19709 ... =======================================================================================SMN APN BOARD GREEN YELLOW RED PRODUCT NR REV DATE SERIAL NR TEMP=======================================================================================0 1 CBU1 ON 16HZ OFF ROJ 119 2209/1 R4B 20060306 TU88281839 +220 9 RAX ON 16HZ OFF ROJ 119 2187/10 R1C 20060301 TU882520480 10 TX ON 16HZ OFF ROJ 119 2240/1 R2A 20060303 TU882706140 11 TX6HS-03 ON 16HZ OFF ROJ 119 2254/3 R3A 20060306 AE526196080 12 RUIF ON 16HZ OFF ROJ 119 2245/2 R1A 20060219 AE52570192---------------------------------------------------------------------------------------================================================================ SMN ProductNr Rev Name Date SerialNr ================================================================ 0 ROJ 605 116/1 R1A Subrack 20040101 Baseband 0 ROJ 605 116/1 R1A BACKPLANE 20060217 TY11320068 ----------------------------------------------------------------

=======================================================================================SMN APN PORT BOARD GREEN YELLOW RED PRODUCT NR REV DATE S=======================================================================================0 12 port_0_dev_5 RU21 steady 16hz off KRC 118 16/2 R1A 20060127 0 12 port_0_dev_5 FU12 ON 16Hz OFF KRC 118 17/1 R2C 20060226 0 12 port_1_dev_11 ASC steady 16hz off KRY 112 42/3 R1F 20060316 0 12 port_4_dev_6 RU21 steady 16hz off KRC 118 16/2 R1A 20060307 0 12 port_4_dev_6 FU12 ON 16Hz OFF KRC 118 17/1 R2C 20060224 0 12 port_5_dev_13 ASC steady 16hz off KRY 112 42/3 R1F 20060316 0 12 port_8_dev_7 RU21 steady 16hz off KRC 118 16/2 R1A 20060307 0 12 port_8_dev_7 FU12 ON 16Hz OFF KRC 118 17/1 R2C 20060222 0 12 port_9_dev_15 ASC steady 16hz off KRY 112 42/3 R1F 20060316 --------------------------------------------------------------------------------------- GRY220> lhsh 001200/port_5_dev_14 asc vswr {check VSWR} Branch:A, VSWR:1.12 (fwdVoltage:3.21V reflVoltage:1.91V fwdPower:21.76dBm reflPower:-3.Branch:B, VSWR:-44.48 (fwdVoltage:1.44V reflVoltage:1.44V fwdPower:-13.11dBm reflPower: RBS 3202 GNJxxx> lhsh AIU_SLOT/port_of_asc /* RBS3202 */ {note: VSWR reading should be less than 1.5} 060923-20:17:33 10.230.64.241 6.1zr RBS_NODE_MODEL_H_6_3 stopfile=/tmp/19709 $ lhsh 001200/port_1_dev_11 asc vswr Branch:A, VSWR:1.29 (fwdVoltage:3.27V reflVoltage:2.40V fwdPower:28.50dBm reflPower:10.Branch:B, VSWR:-3.46 (fwdVoltage:1.42V reflVoltage:1.57V fwdPower:-8.32dBm reflPower:-3$ LNA TRANSISTORS IN ASC GNJ039> lhsh 001200/port_1_dev_11 asc lnaerr 060923-20:17:56 10.230.64.241 6.1zr RBS_NODE_MODEL_H_6_3 stopfile=/tmp/19709 $ lhsh 001200/port_1_dev_11 asc lnaerr LNA transistors branch A OK LNA transistors branch B OK $ CHECK FEEDER CURRENT /* Note: feeder current should almost equal in both branches */ GRY220> cabx =======================================================================================SMN APN BOARD GREEN YELLOW RED PRODUCT NR REV DATE SERIAL NR TEMP COREMGR =======================================================================================0 1 CBU1 ON 16HZ OFF ROJ 119 2209/1 R4B 20060803 TU89364175 +210 2 ET-MC1 ON OFF OFF ROJ 119 2163/1 R5B 20060722 TU892881590 8 RAX13 ON 16HZ OFF ROJ 119 2187/4 R1E 20060823 AE532399000 9 RAX13 ON 16HZ OFF ROJ 119 2187/4 R1E 20060823 AE532399380 10 TX ON 16HZ OFF ROJ 119 2240/1 R2A 20050609 TU863688780 11 TX6HS-03 ON 16HZ OFF ROJ 119 2254/5 R2C 20060721 AE531040610 12 RUIF ON 16HZ OFF ROJ 119 2245/2 R2A 20060802 AE53149711 ================================================================ SMN ProductNr Rev Name Date SerialNr ================================================================ 0 ROJ 605 116/1 R1A Subrack 20040101 Baseband 0 ROJ 605 116/1 R1B BACKPLANE 20060609 TY11427985

=======================================================================================SMN APN PORT BOARD GREEN YELLOW RED PRODUCT NR REV DATE =======================================================================================0 12 port_0_dev_5 RU22 steady 16hz off KRC 118 18/1 R1C 20060719 A0 12 port_0_dev_5 FU12 ON 16Hz OFF KRC 118 17/1 R2D 20060814 T0 12 port_1_dev_12 ASC steady 16hz off KRY 112 42/3 R1D 20050719 T0 12 port_4_dev_6 RU22 steady 16hz off KRC 118 18/1 R1C 20060823 A0 12 port_4_dev_6 FU12 ON 16Hz OFF KRC 118 17/1 R2D 20060817 T0 12 port_5_dev_14 ASC steady 16hz off KRY 112 42/3 R1D 20050505 T0 12 port_8_dev_7 RU22 steady 16hz off KRC 118 18/1 R1C 20060823 A0 12 port_8_dev_7 FU12 ON 16Hz OFF KRC 118 17/1 R2D 20060817 T0 12 port_9_dev_16 ASC steady 16hz off KRY 112 42/3 R1D 20050505 T--------------------------------------------------------------------------------------- GRY220> lhsh 001200/port_4_dev_6 fui get devstat {check feeder current} Board: fuHw: Hw21P3, faultStatus: 0x0, temp: 18.0, sv: on, svTmaDegrad: on, comp: on Dev1: mode: {ModeAuxAsc}, feedVolt: highPow capability: {resAntSv | tma21Sv | ulGainConf | maxUlGain} svCtrl: 0x0500, faultStatus: 0x0400 txFreq: 0, sensitivity: 0, gainUl: -8.3, volt: 29139.2, curr: 7.6, dCycl Dev2: mode: {ModeAuxAsc}, feedVolt: highPow capability: {resAntSv | tma21Sv | ulGainConf | maxUlGain} svCtrl: 0x0500, faultStatus: 0x0000 txFreq: 0, sensitivity: 0, gainUl: -8.3, volt: 28864.9, curr: 324.8, dCyc/* Feeder Branch2 short-circuited. Perform visual check of jumper & connector. Do distafault and check feeder VSWR reading */ Find RNC/RXI Port to the RBS RNC> lt ^utranc|iub|etm|aal RNC> lcc <nodeB_label> /* Print utrancell,rach,fach,pch,synch & nbap. Note that both nBapC & nBapD become enabe1 is looped */ RNC> lst <nodeB_label> {e.g GRY108} RNC> get <proxy_of_nBapC/nBapD> {proxy no} /* Previous step yield the nodeB ID for use in next step. Note that aal2, aal5, & aal0 to an atmport, & to physical e1. Cmd get <proxy_numb> will show the atmport. If RXI is as aal2 switch besides RNC, then aal2path is defined in RXI instead of RNC, so repeat c*/ RNC> lst <nodeB_ID> {for e.g b2000. See sample printout below} 070510-17:01:11 172.24.12.207 7.0 RESTRICTED RNC_NODE_MODEL_F_5_2 stopfile=/tmp/17059 =================================================================================== Proxy Adm State Op. State MO =================================================================================== 10710 1 (ENABLED) TransportNetwork=1,Aal2PathVccTp=b1061a2 {aal2 path} 10711 1 (DISABLED) TransportNetwork=1,Aal2PathVccTp=b1061a1 {aal2 path} 12906 1 (ENABLED) TransportNetwork=1,Aal5TpVccTp=b1061qb {q.2630.1 signalling}12907 1 (ENABLED) TransportNetwork=1,Aal5TpVccTp=b1061qa {q.2630.1 signalling}12912 1 (ENABLED) TransportNetwork=1,Aal5TpVccTp=b1061db {nBap Dedicated} 12913 1 (ENABLED) TransportNetwork=1,Aal5TpVccTp=b1061da {nBap Dedicated} 12916 1 (ENABLED) TransportNetwork=1,Aal5TpVccTp=b1061cb {nBap Common} 12917 1 (ENABLED) TransportNetwork=1,Aal5TpVccTp=b1061ca {nBap Common} 13819 1 (ENABLED) TransportNetwork=1,Aal0TpVccTp=b1061sb1 {rbs synch} 13820 1 (ENABLED) TransportNetwork=1,Aal0TpVccTp=b1061sa1 {rbs synch} 14175 0 (DISABLED) TransportNetwork=1,Aal2Sp=1,Aal2Ap=b1061 {aal2 sig point} 16059 1 (ENABLED) TransportNetwork=1,UniSaalTp=b1061qb {atm adapt for q.2630.1 sig16060 1 (ENABLED) TransportNetwork=1,UniSaalTp=b1061qa {atm adapt for q.2630.1 sig16061 1 (ENABLED) TransportNetwork=1,UniSaalTp=b1061db {atm adapt for nbapD signal16062 1 (ENABLED) TransportNetwork=1,UniSaalTp=b1061da {atm adapt for nbapD signal16063 1 (ENABLED) TransportNetwork=1,UniSaalTp=b1061cb {atm adapt for nBapC signal

Comment [S1]: 1=Unlocked 0=Unlocked

16064 1 (ENABLED) TransportNetwork=1,UniSaalTp=b1061ca {atm adapt for nBapC signal=================================================================================== Total: 17 MOs /* Find the atmport port id, e.g Atmport=ES-2-2-1-ima49. */ RNC> get <proxy of 1st/2nd aal2path> /* one can easily locate the physical port using cmd lko, though not necessary since atnamed for easy association with physical connection, so Jump to step_4 */ RNC> lko atmport=w-x-y-z OR RNC> get atmport=w-x-y-z uses {yield the same result} /* IMAGROUP may contain more than 1 IMALINK, hence more e1, so it is imperative these sperformed since atmport label only tells about 1 physical connection */ Step_1> lcc imagroup=ES-2-2-1-ima49 /* Imalink is tied to a physical connection. One Imalink for each e1 */ Step_2> lst imagroup=ES-2-2-1-ima49 Step_3> get <proxy_imagroup> /* Next, Use the ETM port obtained in step_3. If port is VC12, then proceed to step_5. port is VC4(STM1), then RBS is connected to an aggregator (RXI, HUB_RBS, Or Tellabs_Aggwhich makes it more complicated. Click link below to see sample printout when a site isto Tellab_Aggregator. Sample Printout Printout below is obtained when RXI or another HUB_RBS is used as VC crossconenct to coports from nodeB to RNC. So perform steps 4a-4f. */ Step_4a_RXI> lt atmcrossconnect Step_4b_RXI> lst atmcrossconnection=<nodeB_ID> {e.g b1021, obtained in earlier step. Sbelow} /* This printout is taken from RXI used as atm aggregator */ 070513-22:59:56 10.10.1.25 7.0 RESTRICTED MOM-CELLO_4.3.2-3_5_1 stopfile=/tmp/12314 =================================================================================== Proxy Adm State Op. State MO =================================================================================== 124 1 (ENABLED) TransportNetwork=1,AtmCrossConnection=b1061sb1 {node synch} 128 1 (ENABLED) TransportNetwork=1,AtmCrossConnection=b1061sa1 {node synch} 208 1 (ENABLED) TransportNetwork=1,AtmCrossConnection=b1061qb {q.aal2 sig} 209 1 (ENABLED) TransportNetwork=1,AtmCrossConnection=b1061qa {q.aal2 sig} 222 1 (ENABLED) TransportNetwork=1,AtmCrossConnection=b1061ib {Mub} 223 1 (ENABLED) TransportNetwork=1,AtmCrossConnection=b1061ia {Mub} 234 1 (ENABLED) TransportNetwork=1,AtmCrossConnection=b1061db {nbapD} 235 1 (ENABLED) TransportNetwork=1,AtmCrossConnection=b1061da {nbapD} 239 1 (ENABLED) TransportNetwork=1,AtmCrossConnection=b1061cb {nbapC} 240 1 (ENABLED) TransportNetwork=1,AtmCrossConnection=b1061ca {nbapC} 253 1 (ENABLED) TransportNetwork=1,AtmCrossConnection=b1061a1 {aal2path} =================================================================================== Total: 11 Mos /* This printout is taken from NodeB used as atm aggregator */ GRY108> lst AtmCrossConnection=b1279 070611-22:40:52 10.230.16.45 7.0 RESTRICTED RBS_NODE_MODEL_H_6_6 stopfile=/tmp/28990 =================================================================================== Proxy Adm State Op. State MO =================================================================================== 1363 1 (ENABLED) TransportNetwork=1,AtmCrossConnection=b1279sb1 {node synch} 1364 1 (ENABLED) TransportNetwork=1,AtmCrossConnection=b1279sa1 {node synch} 1400 1 (ENABLED) TransportNetwork=1,AtmCrossConnection=b1279qb {q.aal2 sig} 1401 1 (ENABLED) TransportNetwork=1,AtmCrossConnection=b1279qa {q.aal2 sig}

Comment [S2]: HUB RBS

Comment [S3]: The nodeB_ID of nodeB connected to HUB_RBS GRY108

1411 1 (ENABLED) TransportNetwork=1,AtmCrossConnection=b1279ib {Mub} 1412 1 (ENABLED) TransportNetwork=1,AtmCrossConnection=b1279ia {Mub} 1459 1 (ENABLED) TransportNetwork=1,AtmCrossConnection=b1279db {nbapD} 1461 1 (ENABLED) TransportNetwork=1,AtmCrossConnection=b1279da {nbapD} 1462 1 (ENABLED) TransportNetwork=1,AtmCrossConnection=b1279cb {nbapC} 1463 1 (ENABLED) TransportNetwork=1,AtmCrossConnection=b1279ca {nbapC} 1464 1 (ENABLED) TransportNetwork=1,AtmCrossConnection=b1279a2 {aal2path} 1465 1 (ENABLED) TransportNetwork=1,AtmCrossConnection=b1279a1 {aal2path} =================================================================================== Total: 12 Mos Step_4c_RXI> get <any_proxy_from_above> 070514-21:59:13 10.10.1.25 7.0 RESTRICTED MOM-CELLO_4.3.2-3_5_1 stopfile=/tmp/6084 =======================================================================================364 TransportNetwork=1,AtmCrossConnection=b1061ca =======================================================================================AtmCrossConnectionId b1061ca operationalState 1 (ENABLED) userLabel vclTpAId AtmPort=MS-27-1,VplTp=vp1,VpcTp=1,VclTp=vc536 {ETM4 to RNC} vclTpBId AtmPort=1-8-5,VplTp=vp1,VpcTp=1,VclTp=vc36 {E1 to NodeB} ======================================================================================= OR Step_4c_NodeB> get 1464 {from GRY108 printout above} 070611-22:41:42 10.230.16.45 7.0 RESTRICTED RBS_NODE_MODEL_H_6_6 stopfile=/tmp/28990 =======================================================================================1464 TransportNetwork=1,AtmCrossConnection=b1279a2 =======================================================================================AtmCrossConnectionId b1279a2 operationalState 1 (ENABLED) userLabel vclTpAId AtmPort=1-20-1,VplTp=vp1,VpcTp=1,VclTp=vc240 {ETM4 to RNC} vclTpBId AtmPort=1-2-ima1,VplTp=vp1,VpcTp=1,VclTp=vc40 {E1 to nodeB} ======================================================================================= Step_4d_RXI> lt etm {from ATMport label above} Step_4e_RXI> lcc <subrac=x,slot=y,piu=z,...vc12ttp=a…> Step_4f_RXI> lst vc12ttp=a Step_5> lcc < Subrack=X,Slot=Y,PlugInUnit=Z> Step_6> lst <vc12Ttp=XX> Step_7> st <proxy from step_5> Step_8> pget <proxy> {check e1 error} End_of_procedure Find the RBS for this e1 /* When you see e1 alarms in RNC/RXI but don’t know which RBS it connects to */ =======================================================================================Date & Time (Local) S Specific Problem Cause Mo-=======================================================================================2007-04-21 14:27:46 M IMA Group Insufficient Links local_node_transmission_errorImaGroup=ES-1-2-1-ima59 >>> Total: 5 Alarms (1 Critical, 3 Major) {I assume that when e1 is used, it contains an atmport. No atmport, means not used....} 3RJ01> lt all 3RJ01> lget aal vcltpid atmport=ES-1-2-1-ima59 070515-23:00:09 172.30.204.32 7.0 RESTRICTED RNC_NODE_MODEL_F_5_2 stopfile=/tmp/14286

=======================================================================================MO Attribute Value =======================================================================================Aal2PathVccTp=b2194a2 vclTpId AtmPort=ES-1-2-1-ima59,VplTp=vp1,VpcTp=1,VclAal2PathVccTp=b2194a1 vclTpId AtmPort=ES-1-2-1-ima59,VplTp=vp1,VpcTp=1,VclAal5TpVccTp=b2194qb vclTpId AtmPort=ES-1-2-1-ima59,VplTp=vp1,VpcTp=1,VclAal5TpVccTp=b2194qa vclTpId AtmPort=ES-1-2-1-ima59,VplTp=vp1,VpcTp=1,VclAal5TpVccTp=b2194db vclTpId AtmPort=ES-1-2-1-ima59,VplTp=vp1,VpcTp=1,VclAal5TpVccTp=b2194da vclTpId AtmPort=ES-1-2-1-ima59,VplTp=vp1,VpcTp=1,VclAal5TpVccTp=b2194cb vclTpId AtmPort=ES-1-2-1-ima59,VplTp=vp1,VpcTp=1,VclAal5TpVccTp=b2194ca vclTpId AtmPort=ES-1-2-1-ima59,VplTp=vp1,VpcTp=1,VclAal0TpVccTp=b2194sb1 vclTpId AtmPort=ES-1-2-1-ima59,VplTp=vp1,VpcTp=1,VclAal0TpVccTp=b2194sa1 vclTpId AtmPort=ES-1-2-1-ima59,VplTp=vp1,VpcTp=1,Vcl=======================================================================================Total: 10 MOs 3RR01> lget AtmCrossConnection vcltpbid Atmport=ES-2-24-1 {print the crossconnect, whencmd yield nothing. Printout below is for different nodeB where aal layers are defined ionly imagroup & physical layer is in RXI} RXI106> lget AtmCrossConnection vcltpbid Atmport=1-10-ima8 070606-10:38:31 10.10.1.17 7.0 RESTRICTED MOM-CELLO_4.3.2-3_5_1 stopfile=/tmp/2123 =======================================================================================MO Attribute Value =======================================================================================AtmCrossConnection=b1042sb1 vclTpBId AtmPort=1-10-ima8,VplTp=vp1,VpcTp=1,VclAtmCrossConnection=b1042sa1 vclTpBId AtmPort=1-10-ima8,VplTp=vp1,VpcTp=1,VclAtmCrossConnection=b1042qb vclTpBId AtmPort=1-10-ima8,VplTp=vp1,VpcTp=1,VclAtmCrossConnection=b1042qa vclTpBId AtmPort=1-10-ima8,VplTp=vp1,VpcTp=1,VclAtmCrossConnection=b1042ib vclTpBId AtmPort=1-10-ima8,VplTp=vp1,VpcTp=1,VclAtmCrossConnection=b1042ia vclTpBId AtmPort=1-10-ima8,VplTp=vp1,VpcTp=1,VclAtmCrossConnection=b1042db vclTpBId AtmPort=1-10-ima8,VplTp=vp1,VpcTp=1,VclAtmCrossConnection=b1042da vclTpBId AtmPort=1-10-ima8,VplTp=vp1,VpcTp=1,VclAtmCrossConnection=b1042cb vclTpBId AtmPort=1-10-ima8,VplTp=vp1,VpcTp=1,VclAtmCrossConnection=b1042ca vclTpBId AtmPort=1-10-ima8,VplTp=vp1,VpcTp=1,VclAtmCrossConnection=b1042a2 vclTpBId AtmPort=1-10-ima8,VplTp=vp1,VpcTp=1,VclAtmCrossConnection=b1042a1 vclTpBId AtmPort=1-10-ima8,VplTp=vp1,VpcTp=1,Vcl=======================================================================================Total: 12 MOs AND 3RJ01> lget iublink standbyUniSaalTpRef UniSaalTp=b2194 070515-23:08:19 172.30.204.32 7.0 RESTRICTED RNC_NODE_MODEL_F_5_2 stopfile=/tmp/14286 =======================================================================================MO Attribute Value =======================================================================================IubLink=Iub_GNJ059,NbapDedicated=1 standbyUniSaalTpRef UniSaalTp=bIubLink=Iub_GNJ059,NbapCommon=1 standbyUniSaalTpRef UniSaalTp=b======================================================================================= Utrancell/RACH/FACH/PCH disabled but MOSHELL/EMAS OK Normally, you will see this: GRY401> lpr atm 061115-15:40:04 10.230.16.53 6.1zr RBS_NODE_MODEL_H_6_5 stopfile=/tmp/16717 =================================================================================== Proxy MO =================================================================================== 14 TransportNetwork=1,AtmPort=1-1-ima1 15 TransportNetwork=1,AtmTrafficDescriptor=C2P3900 16 TransportNetwork=1,AtmTrafficDescriptor=U4 17 TransportNetwork=1,AtmTrafficDescriptor=U42 18 TransportNetwork=1,AtmTrafficDescriptor=C1P5

19 TransportNetwork=1,AtmTrafficDescriptor=C1P4400 20 TransportNetwork=1,AtmTrafficDescriptor=U3P1000M80 21 IpSystem=1,Ip=1,IpAtmLink=2 22 IpSystem=1,Ip=1,IpAtmLink=1 =================================================================================== Total: 9 MOs GRY401> lst atm 061115-15:40:11 10.230.16.53 6.1zr RBS_NODE_MODEL_H_6_5 stopfile=/tmp/16717 =================================================================================== Proxy Adm State Op. State MO =================================================================================== 14 1 (ENABLED) TransportNetwork=1,AtmPort=1-1-ima1 21 0 (DISABLED) IpSystem=1,Ip=1,IpAtmLink=2 22 1 (ENABLED) IpSystem=1,Ip=1,IpAtmLink=1 =================================================================================== Total: 3 MOs NOT THE ONE BELOW!!! GRY274> lpr atm 061115-15:44:26 10.230.0.137 6.1zr RBS_NODE_MODEL_H_6_5 stopfile=/tmp/18504 =================================================================================== Proxy MO =================================================================================== 20 TransportNetwork=1,AtmPort=1-1-ima1 21 TransportNetwork=1,AtmTrafficDescriptor=U4 22 TransportNetwork=1,AtmTrafficDescriptor=C1P4400 23 IpSystem=1,Ip=1,IpAtmLink=2 24 IpSystem=1,Ip=1,IpAtmLink=1 =================================================================================== Total: 5 MOs GRY274> lst atm 061115-15:49:43 10.230.0.137 6.1zr RBS_NODE_MODEL_H_6_5 stopfile=/tmp/18504 =================================================================================== Proxy Adm State Op. State MO =================================================================================== 20 1 (ENABLED) TransportNetwork=1,AtmPort=1-1-ima1 23 0 (DISABLED) IpSystem=1,Ip=1,IpAtmLink=2 24 1 (ENABLED) IpSystem=1,Ip=1,IpAtmLink=1 =================================================================================== Total: 3 MOs Make CV and reload with that CV. Always make CV after installing new hwd such as ASC/REthat hwd is not yet configured for the RBS Carrier & Channels In NodeB > lt carrier > lcc carrier > lst 061116-15:50:46 10.230.9.61 6.1zr RBS_NODE_MODEL_H_6_3 stopfile=/tmp/28890 =================================================================================== Proxy Adm State Op. State MO =================================================================================== 8 1 (ENABLED) NodeBFunction=1,Sector=3,Carrier=1 9 1 (ENABLED) NodeBFunction=1,Sector=2,Carrier=1 10 1 (ENABLED) NodeBFunction=1,Sector=1,Carrier=1 64 1 (ENABLED) NodeBFunction=1,Sector=2,Carrier=1,Ssch=1

65 1 (ENABLED) NodeBFunction=1,Sector=2,Carrier=1,Psch=1 66 1 (ENABLED) NodeBFunction=1,Sector=2,Carrier=1,Pcpich=1 67 1 (ENABLED) NodeBFunction=1,Sector=2,Carrier=1,Pccpch=1 68 1 (ENABLED) NodeBFunction=1,Sector=2,Carrier=1,Pccpch=1,Bch=1 69 1 (ENABLED) NodeBFunction=1,Sector=2,Carrier=1,Sccpch=1 70 1 (ENABLED) NodeBFunction=1,Sector=2,Carrier=1,Sccpch=1,Pch=1 71 1 (ENABLED) NodeBFunction=1,Sector=2,Carrier=1,Pich=1 72 1 (ENABLED) NodeBFunction=1,Sector=2,Carrier=1,Sccpch=2 73 1 (ENABLED) NodeBFunction=1,Sector=2,Carrier=1,Sccpch=2,Fach=1 74 1 (ENABLED) NodeBFunction=1,Sector=2,Carrier=1,Sccpch=2,Fach=2 75 1 (ENABLED) NodeBFunction=1,Sector=2,Carrier=1,HsDschResources=1 76 1 (ENABLED) NodeBFunction=1,Sector=2,Carrier=1,Prach=1 77 1 (ENABLED) NodeBFunction=1,Sector=2,Carrier=1,Prach=1,Rach=1 78 1 (ENABLED) NodeBFunction=1,Sector=2,Carrier=1,Aich=1 80 1 (ENABLED) NodeBFunction=1,Sector=1,Carrier=1,Ssch=1 81 1 (ENABLED) NodeBFunction=1,Sector=1,Carrier=1,Psch=1 82 1 (ENABLED) NodeBFunction=1,Sector=1,Carrier=1,Pcpich=1 83 1 (ENABLED) NodeBFunction=1,Sector=1,Carrier=1,Pccpch=1 84 1 (ENABLED) NodeBFunction=1,Sector=1,Carrier=1,Pccpch=1,Bch=1 85 1 (ENABLED) NodeBFunction=1,Sector=1,Carrier=1,Sccpch=2 86 1 (ENABLED) NodeBFunction=1,Sector=1,Carrier=1,Sccpch=2,Fach=1 87 1 (ENABLED) NodeBFunction=1,Sector=1,Carrier=1,Sccpch=2,Fach=2 88 1 (ENABLED) NodeBFunction=1,Sector=1,Carrier=1,Sccpch=1 89 1 (ENABLED) NodeBFunction=1,Sector=1,Carrier=1,Sccpch=1,Pch=1 90 1 (ENABLED) NodeBFunction=1,Sector=1,Carrier=1,Pich=1 91 1 (ENABLED) NodeBFunction=1,Sector=1,Carrier=1,HsDschResources=1 92 1 (ENABLED) NodeBFunction=1,Sector=1,Carrier=1,Prach=1 93 1 (ENABLED) NodeBFunction=1,Sector=1,Carrier=1,Prach=1,Rach=1 94 1 (ENABLED) NodeBFunction=1,Sector=1,Carrier=1,Aich=1

UE REGISTER 3RJ01> ueregprint sum 061118-22:29:34 172.30.204.32 6.1zr RNC_NODE_MODEL_F_5_2 stopfile=/tmp/2604 Trying password from ipdatabase file: /home/ehassha/moshell/./sitefiles/ipdatabase... $ ueregprint sum 527 UEs registered. OR.. 3RJ01> ueregprint all 061118-22:30:46 172.30.204.32 6.1zr RNC_NODE_MODEL_F_5_2 stopfile=/tmp/2604 $ ueregprint all rncModuleId ueCtxt imsi rnti sRnc sRnti 0 24 420012500115043 16408 0 117 16501 0 179 420012500112181 16563 0 281 420012500240483 16665 0 291 420013500274189 16675 TxDeviceGroup_GeneralHwError GNJ011> alt Nr of active alarms are: 1 =======================================================================================Date & Time (Local) S Specific Problem Cause Mo-=======================================================================================2007-05-29 12:34:55 M TrDeviceSet_GeneralHwError equipment_malfunction RbsSubrack=RU1,RbsSlot=4,AuxPlugInUnit=1,RuDeviceGroup=1,TrDeviceSet=1 >>> Total: 1 Alarms (0 Critical, 1 Major) GNJ011> lt plug

GNJ011> lst plug GNJ011> actc <proxy> restart {proxy from prev step} 061119-18:38:35 10.230.65.105 6.1zr RBS_NODE_MODEL_H_6_5 stopfile=/tmp/16368 Call Action restart on following MOs ? =================================================================================== 5 Equipment=1,Subrack=1,Slot=10,PlugInUnit=1 =================================================================================== Are you Sure [y/n] ? y =======================================================================================Proxy MO Action Nr of Params =======================================================================================5 Subrack=1,Slot=10,PlugInUnit=1 restart 2 Parameter 1 of 2, restartRank (enumRef-RestartRank): Enter one of the following integers: 0:RESTART_WARM, 1:RESTART_REFRESH, 2:RESTART_COParameter 2 of 2, restartCause (enumRef-RestartCause): Enter one of the following integers: 2:piuRestartUpgrade, 1:piuRestartError: 1 >>> Return value = null =======================================================================================Total: 1 MOs attempted, 1 MOs actioned AiDevice ExternalUnitFailure AIDEVICE=2 (ANTENNA BRANCH_2) /* Print Alarm */ GRY533> alt =======================================================================================Date & Time (Local) S Specific Problem Cause Mo-=======================================================================================2007-05-16 13:34:34 M AiDevice_ExternalUnitFailure equipment_malfunction RbsSubrack=FU1,RbsSlot=6,AuxPlugInUnit=1,FuDeviceGroup=1,AiDeviceSet=1,AiDevice=2 /* Is sector taking traffic?, if yes mark fault as low priority. Else If sector is disablock the sector in RNC, warm restart nodeB & deblock sector after performing the follosteps*/ RBS>lt radio RBS>get radio /* List plug-in-unit */ GRY533> lt plug GRY533> lst 070516-16:44:29 10.230.17.49 7.0 RESTRICTED RBS_NODE_MODEL_H_6_6 stopfile=/tmp/20556 =================================================================================== Proxy Adm State Op. State MO =================================================================================== 1 1 (UNLOCKED) 1 (ENABLED) Equipment=1,Subrack=1,Slot=9,PlugInUnit=1 2 0 (LOCKED) 0 (DISABLED) Equipment=1,Subrack=1,Slot=8,PlugInUnit=1 3 1 (UNLOCKED) 1 (ENABLED) Equipment=1,Subrack=1,Slot=1,PlugInUnit=1 4 1 (UNLOCKED) 1 (ENABLED) Equipment=1,Subrack=1,Slot=12,PlugInUnit=1 5 1 (UNLOCKED) 1 (ENABLED) Equipment=1,Subrack=1,Slot=11,PlugInUnit=1 6 1 (UNLOCKED) 1 (ENABLED) Equipment=1,Subrack=1,Slot=10,PlugInUnit=1 7 1 (UNLOCKED) 1 (ENABLED) Equipment=1,AuxPlugInUnit=2 8 1 (UNLOCKED) 1 (ENABLED) Equipment=1,SectorAntenna=3,AuxPlugInUnit=2 9 1 (UNLOCKED) 1 (ENABLED) Equipment=1,SectorAntenna=3,AuxPlugInUnit=1 10 1 (UNLOCKED) 1 (ENABLED) Equipment=1,SectorAntenna=2,AuxPlugInUnit=2 11 1 (UNLOCKED) 1 (ENABLED) Equipment=1,SectorAntenna=2,AuxPlugInUnit=1 12 1 (UNLOCKED) 1 (ENABLED) Equipment=1,SectorAntenna=1,AuxPlugInUnit=2 13 1 (UNLOCKED) 1 (ENABLED) Equipment=1,SectorAntenna=1,AuxPlugInUnit=1 14 1 (UNLOCKED) 1 (ENABLED) Equipment=1,RbsSubrack=RU1,RbsSlot=6,AuxPlugInUnit=1 15 1 (UNLOCKED) 1 (ENABLED) Equipment=1,RbsSubrack=RU1,RbsSlot=4,AuxPlugInUnit=1 16 1 (UNLOCKED) 1 (ENABLED) Equipment=1,RbsSubrack=RU1,RbsSlot=2,AuxPlugInUnit=1

17 1 (UNLOCKED) 1 (ENABLED) Equipment=1,RbsSubrack=FU1,RbsSlot=6,AuxPlugInUnit=1 18 1 (UNLOCKED) 1 (ENABLED) Equipment=1,RbsSubrack=FU1,RbsSlot=4,AuxPlugInUnit=1 19 1 (UNLOCKED) 1 (ENABLED) Equipment=1,RbsSubrack=FU1,RbsSlot=2,AuxPlugInUnit=1=================================================================================== RBS> lcc RbsSubrack=FU1,RbsSlot=6,AuxPlugInUnit=1 {load MO for antenna branch} RBS> lst plug {although not shown here, normallare enabled, just proceed with next step} GRY533> actl 8 {list actions on this MO} GRY533> actc 8 restartAuxUnit {restart RET} GRY533> actl 17 {if alm remain, list actions on FU} GRY533> actc 17 restartAuxUnit {restart FU} GRY533> actl 14 {if alm remain, list actions on RU} GRY533> actc 14 restartAuxUnit {restart RU} /* Alarm remain? Check jumper, feeder, RET & RET cable. End of Procedure */ AIDEVICE=1 (ANTENNA BRANCH_1) /* As in previous case, restart FU, then RU. If alarm remain,do the following */ /* Perform VSWR Check. Also check feeder current for short-circuit. feeder current shouequal in both branches. Perform visual check of jumper & connector. Do distance-to-faulcheck feeder VSWR reading. End Of Procedure */ Sector_RejectSignalFromHardware The ASC unit, supervised and controlled by the Sector MO, issued the alarm. The alarm ifault in the unit mentioned above. The operational state of the cell is not affected byfault. Restart ASC, if alarm reappears restart FU,then RU, then perform hwd test on ASCresults show no fault then restart RBS, else replace ASC Aet_iworxDrvAtm_proc_iworxatm

Moshell into affected RXI, and key in command “lhsh XX XX XX te log read” XX XX XX – Affected ET-MC41 board in RXI

If alarm “Aet_iworxDrvAtm_proc iworxatm…………………….Loopbacktimeout (5s)” this indicates ET-MC41 board has hang & restart of board need to be performed. More info Check CPU Load /* Check CPU Load in Main GPB board */ GRY021> capi tot 061209-21:31:06 10.230.0.129 6.1zr RBS_NODE_MODEL_H_6_3 stopfile=/tmp/19120 $ capi tot CPU load report --------------- Integration interval: 100000 microseconds Load (%) 2 /* Check Proc load in all CPU based board */ GRY021> cabl 061209-21:31:28 10.230.0.129 6.1zr RBS_NODE_MODEL_H_6_3 stopfile=/tmp/19120 put /home/ehassha/moshell_logfiles/logs_moshell/tempfiles/tmp19095_20061209-211058/lhCm/c/tmp/lhCmd19095 ... OK

.......... =======================================================================================SMN APN BOARD GREEN YELLOW RED PRODUCT NR REV DATE SERIAL NCOREMGR =======================================================================================0 1 SCB2 ON OFF OFF ROJ 119 2108/3 R3D 20040924 TU84614650 0 2 ET-M1 ON OFF OFF ROJ 119 2101/3 R1B 20040929 TU846768 0 4 TUB ON 16HZ OFF ROJ 119 2104/4 R3B 20041126 TU851332 0 5 TUB ON 16HZ OFF ROJ 119 2104/4 R3B 20041126 TU851332 0 8 RAX ON 16HZ OFF ROJ 119 2187/1 R4F 20040910 TU844607 0 17 TX ON 16HZ OFF ROJ 119 2124/3 R1S 20040831 TU843455 0 20 GPB31 ON 16HZ OFF ROJ 119 2106/31 R1H 20040917 TU845456Active* 0 0 SCB2 ON OFF OFF ROJ 119 2108/3 R3D 20040924 TU846173---------------------------------------------------------------------------------------1 1 SCB2 ON OFF OFF ROJ 119 2108/3 R3D 20040924 TU84617408 1 2 RFIF ON 16HZ OFF ROJ 119 2115/4 R1G 20040921 TU845822 1 4 TRX ON 16HZ OFF ROJ 119 2164/1 R3F 20041018 AE513633 1 6 AIU ON 16HZ OFF KRY1011854/5 R1F 04w40 TR413331 1 7 TRX ON 16HZ OFF ROJ 119 2164/1 R3F 20041019 AE513657 1 9 AIU ON 16HZ OFF KRY1011854/5 R1F 00W01 TR416905 1 10 TRX ON 16HZ OFF ROJ 119 2164/1 R3F 20041018 AE513634 1 12 AIU ON 16HZ OFF KRY1011854/5 R1F 04W40 TR416906 1 0 SCB2 ON OFF OFF ROJ 119 2108/3 R3D 20040924 TU846174---------------------------------------------------------------------------------------=======================================================================================SMN APN BOARD LOAD CAPI TOT ======================================================================================= 0 1 SCB2 1.8 2 2 1 2 2 2 1 2 2 2 0 2 ET-M1 1.7 2 1 1 2 2 3 3 1 1 1 0 4 TUB 0.7 0 0 1 0 0 0 1 0 0 5 0 5 TUB 0.8 5 0 0 1 0 0 1 1 0 0 0 8 RAX 4.0 10 3 4 1 2 3 3 6 3 5 0 17 TX 6.1 20 2 7 2 10 1 3 5 5 6 0 20 GPB31 9.9 12 5 6 18 4 17 5 14 7 11 0 0 SCB2 1.3 1 1 1 2 1 1 1 3 1 1 --------------------------------------------------------------------------------------- 1 1 SCB2 1.3 1 1 2 1 1 2 2 1 1 1 1 2 RFIF 7.7 7 7 7 7 11 7 10 7 7 7 1 4 TRX 3.7 4 3 3 4 5 4 3 4 4 3 1 6 AIU 1.2 1 1 1 1 2 1 1 2 1 1 1 7 TRX 3.5 3 3 3 4 3 3 4 5 3 4 1 9 AIU 1.2 1 2 1 1 1 1 1 2 1 1 1 10 TRX 3.7 3 4 4 3 3 4 3 4 4 5 1 12 AIU 1.4 2 1 1 3 1 1 1 1 1 2 1 0 SCB2 1.5 2 2 1 1 2 2 1 1 1 2 --------------------------------------------------------------------------------------- /* Print CPU load report */ GRY021> capi prio 061209-21:31:49 10.230.0.129 6.1zr RBS_NODE_MODEL_H_6_3 stopfile=/tmp/19120 $ capi prio CPU load report --------------- Integration interval: 100000 microseconds Processes % % % % % % % % % % int 1 1 1 1 1 1 1 1 1 1 bg 97 96 98 97 91 91 96 94 98 98 pri0 0 0 0 0 0 0 0 0 0 0 pri1 0 0 0 0 0 0 0 0 0 0

pri2 0 0 0 0 0 0 0 0 0 0 pri3 0 0 0 0 0 0 0 0 0 0 pri4 0 0 0 0 0 0 0 0 0 0 pri5 0 0 0 0 0 0 0 0 0 0 pri6 0 0 0 0 0 0 0 0 0 0 pri7 0 0 0 0 0 0 0 0 0 0 pri8 0 0 0 0 0 0 0 0 0 0 pri9 0 0 0 0 0 0 0 0 0 0 pri10 0 0 0 0 0 0 0 0 0 0 pri11 0 0 0 0 1 0 0 0 0 0 pri12 1 1 1 1 1 1 1 1 1 1 pri13 0 0 0 0 0 0 0 0 0 0 pri14 0 0 0 0 0 0 0 0 0 0 pri15 0 0 0 0 0 0 0 0 0 0 pri16 0 0 0 0 0 0 0 0 0 0 pri17 0 0 0 0 0 0 0 0 0 0 pri18 0 0 0 0 1 1 0 0 0 0 pri19 0 0 0 0 0 0 0 0 0 0 pri20 0 0 0 0 0 0 0 0 0 0 pri21 0 0 0 0 0 0 0 0 0 0 pri22 0 0 0 0 0 0 0 0 0 0 pri23 1 1 0 0 5 4 1 2 0 0 pri24 0 0 0 0 0 0 0 0 0 0 pri25 0 0 0 0 0 1 0 0 0 0 pri26 0 0 0 0 0 0 0 0 0 0 pri27 0 0 0 0 0 0 0 0 0 0 pri28 0 0 0 0 0 0 0 0 0 0 pri29 0 0 0 0 0 0 0 0 0 0 pri30 0 0 0 0 0 0 0 0 0 0 pri31 0 0 0 0 0 0 0 0 0 0 Total 100 99 100 99 100 99 99 98 100 100 DISK USAGE & HDISK INFO GRY021> vols 061209-21:32:19 10.230.0.129 6.1zr RBS_NODE_MODEL_H_6_3 stopfile=/tmp/19120 $ vols volume total used free frw device unit / 0K 0K 100% 0K 100% FR- /null 0K 0K 100% 0K 100% FRW /d 195M 163M 83% 32M 16% FRW idedd 0 <4-399999> /c 415M 359M 86% 55M 13% FRW mirrordd 0 <400000-1250927> /j 415M 359M 86% 55M 13% FRW /c 0 <400000-1250927> GRY021> hdinfo 061209-21:32:59 10.230.0.129 6.1zr RBS_NODE_MODEL_H_6_3 stopfile=/tmp/19120 $ hdinfo Hard Disk parameters: Size in MB: 640 Sector size: 512 No of cyl.: 1241 No of heads: 16 Sectors/Track: 63 No of sectors: 1250928 HD PIO mode: 1 Model: TOSHIBA THNAT640MBAI Serial number: STAB46M04009C31460E1 Firmware rev: 2.20 ASC/RU/FU COMMANDS RBS3206

/* ASC Commands */ <command> <arguments> Description --------- ----------- ----------- help This text. asc selftest ASC selftest asc vswr measure vswr both branches asc rl measure return loss both branches asc pow measure TX output power both branchesasc intpow measure internal voltage status asc extpow measure external (RET) voltage asc lnatemp measure LNA board temperature asc dpbtemp measure Device Peripheral Board (AUM)temperature asc lnaerrset <[s|b|n] transistors> <[a|b] branch>simulate LNA transistor fault, singleno transistor, branch [a|b] asc lnaerr read current LNA transistor error fauasc hwerrset 0|1 General HW error SBCI reset/set [0|1]detected at self/startup test) asc pset_dpb <excLow><normLow><normHigh><excHigh> set TMAU_TEMP_LIMITS (DP Board) temp.parameters asc pset_lna <excLow><normLow><normHigh><excHigh> set TMA_LNA_TEMP_LIMITS (LNA Board) tparameters asc pset_ext <minVoltage> <maxVoltage> set TMAU_EXT_POW_LIMIT (min and max svoltage parameters asc gaincal <index> <value br A> <value br B> set RAM gain calibration data (0-255)position <index 0-12> /* FU/RU Commands */ =======================================================================================SMN APN PORT BOARD GREEN YELLOW RED PRODUCT NR REV SERIAL NR =======================================================================================0 12 port_0_dev_5 RU21 steady 16hz off KRC 118 16/2 R1A 20060131 0 12 port_0_dev_5 FU ON 16Hz OFF KRC 118 17/1 R2B 20060123 0 12 port_1_dev_11 ASC steady 16hz off KRY 112 42/3 R1F 20060126 0 12 port_4_dev_6 RU21 steady 16hz off KRC 118 16/2 R1A 20060131 0 12 port_4_dev_6 FU ON 16Hz OFF KRC 118 17/1 R2B 20060123 0 12 port_5_dev_13 ASC steady 16hz off KRY 112 42/3 R1F 20060312 0 12 port_8_dev_7 RU21 steady 16hz off KRC 118 16/2 R1A 20060131 0 12 port_8_dev_7 FU ON 16Hz OFF KRC 118 17/1 R2B 20060123 0 12 port_9_dev_15 ASC steady 16hz off KRY 112 42/3 R1F 20060125 /* list the commands for RU/FU fault management*/ GRY070> lhsh 001200/port_8_dev_7 "fm" 061212-10:41:46 10.230.9.61 6.1zr RBS_NODE_MODEL_H_6_3 stopfile=/tmp/2192 $ lhsh 001200/port_8_dev_7 "fm" Usage: {collect|restore|fcease|dtime|mask|getmask|unmask|getfaults} /* Check RU/FU faults */ GRY070> lhsh 001200/port_8_dev_7 fm getfaults 061212-10:24:07 10.230.9.61 6.1zr RBS_NODE_MODEL_H_6_3 stopfile=/tmp/2192 $ lhsh 001200/port_8_dev_7 fm getfaults No raised fault was found /* list the commands for Access to the FU Hwd */ GRY070> lhsh 001200/port_8_dev_7 "fui" "get" 061212-11:41:47 10.230.9.61 6.1zr RBS_NODE_MODEL_H_6_3 stopfile=/tmp/2192 $ lhsh 001200/port_8_dev_7 "fui" "get" Usage: get {{curr <devId> <nof values>} | {volt <devId> <nof values>} | vswr | temp | fdevstat | adcpar | {ee data} | {ee pid} | {ee image}}

/* Check FU & Antenna System */ GRY070> lhsh 001200/port_8_dev_7 fui get faults 061212-11:42:22 10.230.9.61 6.1zr RBS_NODE_MODEL_H_6_3 stopfile=/tmp/2192 $ lhsh 001200/port_8_dev_7 fui get faults Board: database : ok i2c : ok highPow : ok Dev1: lna : ok ant : ok extAux : ok vswr : ok pll : ok tmaLna : ok Dev2: lna : ok ant : ok extAux : ok vswr : ok pll : ok tmaLna : ok ALARM EVENT LOGGING GRY070> lgasmi 2h /* Print alarm log for previous 2hours max30hrs */ GRY070> lgaev 2h /* Print event log for previous 2hours max30hrs */ Cello> lgo /* List COMMAND Log */ Cello> lgh /* Hw Inventory Log */ Cello> lgs /* System Log – restart CMD etc */ Cello> lgv /* Availability log */ Cello> llog /* Restart log */ Cello> lh all llog /* Restart log on all boards & aux units */ OR Cello> all llog /* Similar output as previous cmd */ Cello> lgd /* Print Downtime duration due to restart or upgrade */ Cello> lgu /* Upgrade log */ GRY070> l+ /* start logging to file */ GRY070> l- /* end logging to file */ SOFTWARE ALLOCATION & WHICH BOARD RNC> lt root /* Clear proxy */ RNC> lt swa /* load SwAllocation */ RNC> lpr /* list proxy’s */ RNC> get <proxy> /* get proxy of required sw */ PHYSICAL LINK USED BY GCP SIGNALLING BETWEEN MGW MSC-SERVER 3GJ01> lt aal5 3GJ01> lst aal5 Proxy Adm State Op. State MO =================================================================================== 19 1 (ENABLED) TransportNetwork=1,Aal5TpVccTp=Aal5Tp_3MJ1_6 20 1 (ENABLED) TransportNetwork=1,Aal5TpVccTp=Aal5Tp_3MJ1_5 21 1 (ENABLED) TransportNetwork=1,Aal5TpVccTp=Aal5Tp_3MJ1_4

22 1 (ENABLED) TransportNetwork=1,Aal5TpVccTp=Aal5Tp_3MJ1_3 23 1 (ENABLED) TransportNetwork=1,Aal5TpVccTp=Aal5Tp_3MJ1_2 24 1 (ENABLED) TransportNetwork=1,Aal5TpVccTp=Aal5Tp_3MJ1_1 25 1 (ENABLED) TransportNetwork=1,Aal5TpVccTp=Aal5Tp_3GJ2_2 26 1 (ENABLED) TransportNetwork=1,Aal5TpVccTp=Aal5Tp_3GJ2_1 =================================================================================== Total: 26 MOs 3GJ01> lget 19 20 21 22 23 24 vcltpid MO Attribute Value =======================================================================================Aal5TpVccTp=Aal5Tp_3MJ1_6 vclTpId AtmPort=2051,VplTp=2,VpcTp=1,VcAal5TpVccTp=Aal5Tp_3MJ1_5 vclTpId AtmPort=2051,VplTp=2,VpcTp=1,VcAal5TpVccTp=Aal5Tp_3MJ1_4 vclTpId AtmPort=2051,VplTp=2,VpcTp=1,VcAal5TpVccTp=Aal5Tp_3MJ1_3 vclTpId AtmPort=2041,VplTp=2,VpcTp=1,VcAal5TpVccTp=Aal5Tp_3MJ1_2 vclTpId AtmPort=2041,VplTp=2,VpcTp=1,VcAal5TpVccTp=Aal5Tp_3MJ1_1 vclTpId AtmPort=2041,VplTp=2,VpcTp=1,Vc================ Total: 6 MOs 3GJ01> lst atmport=2051|atmport=2041 Proxy Adm State Op. State MO =================================================================================== 621 1 (ENABLED) TransportNetwork=1,AtmPort=2051 623 1 (ENABLED) TransportNetwork=1,AtmPort=2041 3GJ01> lget 621 623 userlabel MO Attribute Value =======================================================================================AtmPort=2051 userLabel AtmPort 2051 for ETM4 Subrack 2 SAtmPort=2041 userLabel AtmPort 2041 for ETM4 Subrack 2 S ATM LAYER INFO WHEN RBS CONNECT TO RXI RXI106> lst b26079 070122-01:01:46 10.10.1.17 7.0 RESTRICTED MOM-CELLO_4.3.2-3_5_1 stopfile=/tmp/28197 =================================================================================== Proxy Adm State Op. State MO =================================================================================== 91 1 (UNLOCKED) 1 (ENABLED) TransportNetwork=1,Aal2PathVccTp=b26079a2 92 1 (UNLOCKED) 1 (ENABLED) TransportNetwork=1,Aal2PathVccTp=b26079a1 134 1 (ENABLED) TransportNetwork=1,Aal5TpVccTp=b26079qb 135 1 (ENABLED) TransportNetwork=1,Aal5TpVccTp=b26079qa 224 1 (ENABLED) TransportNetwork=1,Aal2Sp=1,Aal2Ap=b26079 266 1 (ENABLED) TransportNetwork=1,UniSaalTp=b26079qb 267 1 (ENABLED) TransportNetwork=1,UniSaalTp=b26079qa =================================================================================== RXI106> get 92 vcltpid =======================================================================================MO Attribute Value =======================================================================================Aal2PathVccTp=b26079a1 vclTpId AtmPort=1-8-3,VplTp=vp1,VpcTp=1,Vcl==================================================================================== /* atmcrossconnect means this Vc terminates in processor inside RNC Bear in mind aal5 must terminate in board processor */ RXI106> lget AtmPort=1-8-3 atmTrafficDescriptorId|reservedBy 070122-01:48:09 10.10.1.17 7.0 RESTRICTED MOM-CELLO_4.3.2-3_5_1 stopfile=/tmp/28197

=======================================================================================MO Attribute Value =======================================================================================AtmPort=1-8-3,VplTp=vp1,VpcTp=1,VclTp=vc45 atmTrafficDescriptorId AtmTrafficDescriptor=AtmPort=1-8-3,VplTp=vp1,VpcTp=1,VclTp=vc45 reservedBy Aal5TpVccTp=b26079qb AtmPort=1-8-3,VplTp=vp1,VpcTp=1,VclTp=vc44 atmTrafficDescriptorId AtmTrafficDescriptor=AtmPort=1-8-3,VplTp=vp1,VpcTp=1,VclTp=vc44 reservedBy AtmCrossConnection=b2 AtmPort=1-8-3,VplTp=vp1,VpcTp=1,VclTp=vc43 atmTrafficDescriptorId AtmTrafficDescriptor=AtmPort=1-8-3,VplTp=vp1,VpcTp=1,VclTp=vc43 reservedBy AtmCrossConnection=b2 AtmPort=1-8-3,VplTp=vp1,VpcTp=1,VclTp=vc42 atmTrafficDescriptorId AtmTrafficDescriptor=AtmPort=1-8-3,VplTp=vp1,VpcTp=1,VclTp=vc42 reservedBy AtmCrossConnection=b2 AtmPort=1-8-3,VplTp=vp1,VpcTp=1,VclTp=vc41 atmTrafficDescriptorId AtmTrafficDescriptor=AtmPort=1-8-3,VplTp=vp1,VpcTp=1,VclTp=vc41 reservedBy AtmCrossConnection=b2 AtmPort=1-8-3,VplTp=vp1,VpcTp=1,VclTp=vc40 atmTrafficDescriptorId AtmTrafficDescriptor=AtmPort=1-8-3,VplTp=vp1,VpcTp=1,VclTp=vc40 reservedBy Aal2PathVccTp=b26079a AtmPort=1-8-3,VplTp=vp1,VpcTp=1,VclTp=vc39 atmTrafficDescriptorId AtmTrafficDescriptor=AtmPort=1-8-3,VplTp=vp1,VpcTp=1,VclTp=vc39 reservedBy Aal2PathVccTp=b26079a AtmPort=1-8-3,VplTp=vp1,VpcTp=1,VclTp=vc38 atmTrafficDescriptorId AtmTrafficDescriptor=AtmPort=1-8-3,VplTp=vp1,VpcTp=1,VclTp=vc38 reservedBy Aal5TpVccTp=b26079qa AtmPort=1-8-3,VplTp=vp1,VpcTp=1,VclTp=vc37 atmTrafficDescriptorId AtmTrafficDescriptor=AtmPort=1-8-3,VplTp=vp1,VpcTp=1,VclTp=vc37 reservedBy AtmCrossConnection=b2 AtmPort=1-8-3,VplTp=vp1,VpcTp=1,VclTp=vc36 atmTrafficDescriptorId AtmTrafficDescriptor=AtmPort=1-8-3,VplTp=vp1,VpcTp=1,VclTp=vc36 reservedBy AtmCrossConnection=b2 AtmPort=1-8-3,VplTp=vp1,VpcTp=1,VclTp=vc35 atmTrafficDescriptorId AtmTrafficDescriptor=AtmPort=1-8-3,VplTp=vp1,VpcTp=1,VclTp=vc35 reservedBy AtmCrossConnection=b2 AtmPort=1-8-3,VplTp=vp1,VpcTp=1,VclTp=vc34 atmTrafficDescriptorId AtmTrafficDescriptor=AtmPort=1-8-3,VplTp=vp1,VpcTp=1,VclTp=vc34 reservedBy AtmCrossConnection=b2 AtmPort=1-8-3,VplTp=vp1,VpcTp=1,VclTp=vc33 atmTrafficDescriptorId AtmTrafficDescriptor=AtmPort=1-8-3,VplTp=vp1,VpcTp=1,VclTp=vc33 reservedBy AtmCrossConnection=b2 AtmPort=1-8-3,VplTp=vp1,VpcTp=1,VclTp=vc32 atmTrafficDescriptorId AtmTrafficDescriptor=AtmPort=1-8-3,VplTp=vp1,VpcTp=1,VclTp=vc32 reservedBy AtmCrossConnection=b2 SS7 CHECK /* check disabled MTP3BSRS */ 3GR1> lt mtp3bsrs operationalstate==0 3GR1> lget mtp3bsrs destpointcode /* Find out which SigRoute Uses the LinkSet */ CELLO> lt mtp3bsls CELLO> lget mtp3bls reservedBy /* Find out physical port used by LinkSet Assuming all aal5 properly labelled Will list aal5 for nodeBs if executed in RNC*/ CELLO> lt aal CELLO> lget aal5tpvcctp userlabel|vcltpid OR: 3RR01> lst mtp3bsl 070617-01:07:04 172.24.12.207 7.0 RESTRICTED RNC_NODE_MODEL_F_5_2 stopfile=/tmp/17598 ===================================================================================

Proxy Adm State Op. State MO =================================================================================== 11 1 (ENABLED) TransportNetwork=1,Mtp3bSpItu=1,Mtp3bSls=qcs 12 1 (ENABLED) TransportNetwork=1,Mtp3bSpItu=1,Mtp3bSls=p2s 13 1 (ENABLED) TransportNetwork=1,Mtp3bSpItu=1,Mtp3bSls=p1s 14 1 (ENABLED) TransportNetwork=1,Mtp3bSpItu=1,Mtp3bSls=g2s 15 1 (ENABLED) TransportNetwork=1,Mtp3bSpItu=1,Mtp3bSls=c2s 16 1 (ENABLED) TransportNetwork=1,Mtp3bSpItu=1,Mtp3bSls=c1s 23 1 (ENABLED) TransportNetwork=1,Mtp3bSpItu=1,Mtp3bSls=qcs,Mtp3bSl 24 0 (DISABLED) TransportNetwork=1,Mtp3bSpItu=1,Mtp3bSls=qcs,Mtp3bSl 26 0 (DISABLED) TransportNetwork=1,Mtp3bSpItu=1,Mtp3bSls=qcs,Mtp3bSl 30 0 (DISABLED) TransportNetwork=1,Mtp3bSpItu=1,Mtp3bSls=p1s,Mtp3bSl 38 0 (DISABLED) TransportNetwork=1,Mtp3bSpItu=1,Mtp3bSls=c1s,Mtp3bSl 3RR01> lko 24 070617-01:08:46 172.24.12.207 7.0 RESTRICTED RNC_NODE_MODEL_F_5_2 stopfile=/tmp/17598 =================================================================================== MOs linked to 24 TransportNetwork=1,Mtp3bSpItu=1,Mtp3bSls=qcs,Mtp3bSlItu=g1s2a (-,D)=================================================================================== tpId Mtp3bSpItu=1,Mtp3bSls=qcs,Mtp3bSlItu=g1s2a ---> (-,D) NniSaalaal5TpVccTpId NniSaalTp=g1s2a ---> (-,D) Aal5TpVnniSaalProfileId NniSaalTp=g1s2a ---> (-,-) NniSaalProfile=win250processorId Aal5TpVccTp=g1s2a ---> (U,E) Subrack=MS,Slot=8,PluvclTpId Aal5TpVccTp=g1s2a ---> (-,D) AtmPort=MS-6-1,VplTp=vp1,VpcTp=1,VatmTrafficDescriptorId AtmPort=MS-6-1,VplTp=vp1,VpcTp=1,VclTp=vc37 ---> (-,-) AtmTrafficDescriptor=U3P4500M3000 mtp3bSrsId Mtp3bSpItu=1,Mtp3bSls=qcs ---> (-,E) Mtp3bSpItu=1,Mtp3bSrs=qcs reservedBy Mtp3bSpItu=1,Mtp3bSls=qcs ---> (-,E) Mtp3bSpItu=1,Mtp3bSrs=r103s,Mtp3=================================================================================== Check VC12 is used or not RNC> lt aal2pathvcctpid operationalstate==0 RNC> lst aal2 070212-19:51:06 172.24.12.207 7.0 RESTRICTED RNC_NODE_MODEL_F_5_2 stopfile=/tmp/9982 =================================================================================== Proxy Adm State Op. State MO =================================================================================== 4 1 (UNLOCKED) 0 (DISABLED) TransportNetwork=1,Aal2PathVccTp=b1071a2 5 1 (UNLOCKED) 0 (DISABLED) TransportNetwork=1,Aal2PathVccTp=b1071a1 =================================================================================== RNC> lget aal2 vcltpid 070212-20:03:55 172.24.12.207 7.0 RESTRICTED RNC_NODE_MODEL_F_5_2 stopfile=/tmp/9982 =======================================================================================MO Attribute Value =======================================================================================Aal2PathVccTp=b1071a2 vclTpId AtmPort=ES-2-2-1-ima3,VplTp=vp1,VpcTp=1,VcAal2PathVccTp=b1071a1 vclTpId AtmPort=ES-2-2-1-ima3,VplTp=vp1,VpcTp=1,Vc=======================================================================================RNC> lt imagroup RNC> get imagroup=ES-2-2-1-ima3 physicalPortList E1 ENABLED BUT RBS DOWN DUE TO HANGING IMA RNC/RXI> lt etmc41|imagroup RNC/RXI> lcc <subrack=x,slot=y,piu=z..> RNC/RXI> lst <subrack=x,slot=y,piu=z..>/<vclttp=x of the e1 affected> /* after block/deblock e1 to */ RNC/RXI> lcc imagroup=<a-b-c-d> RNC/RXI> lst imagtoup=<a-b-c-d>

{check if IMAGROUP DISABLED, if yes escalate. Click link below to see sample activity fproblem } ETM Board Restart, Delete & Recreate Site DS0 BUNDLE /* DS0 is ckt emulation for TDM based application. Used for carrying TDM based speech osignalling. Each DS0 Bundle may consist of 1 up to 32 64K TSLOTS. Note there will be noassociated with this physical interface */ MGW> lt ds0 MGW> lst ds0 MGW> get <pick_a_proxy> /* The ReservedBy attribute indicates it’s usage */ 3GR2> get 119 =======================================================================================Equipment=1,Subrack=2,Slot=25,PlugInUnit=1,Etmc1=1,E1PhysPathTerm=3,Ds0Bundle=4 =======================================================================================Ds0BundleId 4 availabilityStatus 0 (NO_STATUS) listOfTimeSlots i[1] = 2 operationalState 1 (ENABLED) reservedBy [1] = >>> reservedBy = TransportNetwork=1,Mtp2TpItu=4 /* narrowband signalling */ tdmMode true userLabel DS0_STG9_22523-6 /* STG=signalling xfer Group */ ======================================================================================= 3GR2> get 184 =======================================================================================Equipment=1,Subrack=2,Slot=21,PlugInUnit=1,Etmc41=1,Os155SpiTtp=ATM-21-1,Vc4Ttp=1,Vc12Ttp=11,E1Ttp=1,Ds0Bundle=ATM-21-1-11 =======================================================================================Ds0BundleId ATM-21-1-11 availabilityStatus 0 (NO_STATUS) listOfTimeSlots i[31] = 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 21 22 23 24 25 26 27 28 29 30 31 operationalState 1 (ENABLED) reservedBy [1] = >>> reservedBy = MgwApplication=1,TdmTermGrp=11 /* 64K based ckt switched */ tdmMode true userLabel DS0_TSR1_221111_363-2337 /* Huawei 2G MSC */ ======================================================================================= SECTOR DOWN RBS NO ALARM /* Call establishment error in RNC, sector down & no alarm in nodeB */ NodeB> te log read eFroId=403243010, deviceGlobalId=2306. [2007-05-15 18:12:16.876] eqcDevNoAllocDevProxyCR1 ../src/EqcNehDbccDevProxyC.cpp:165 INFO://TX:0:11::// DBCC Device Setup successful: dbccDeviceFroId=402718721, deviceGloba[2007-05-15 18:12:16.880] eqcDevNoAllocDevProxyCR1 ../src/EqcNehDbccDevProxyC.cpp:165 INFO://TX:0:10::// DBCC Device Setup successful: dbccDeviceFroId=402915329, deviceGloba[2007-05-15 18:12:19.100] eqcEfhFhEncC[91] ../src/EqcEfhAiDeviceFhEncC.cpp:1121 INFO:ABN:Equipment fault: /FU:0:12:0:2/, global id: EQC_EFH_FRO_TYPE_AI-1, auxPowerSvFafaultType: AI_FAULT_TYPE_ANTENNA_FEEDER_CURRENT_TOO_HIGH, faultTypeId: 420, faultRecoveAI_RECOVERY_ACTION_NO_SUGGESTED_ACTION, faultDescription: Not supplied {Note that FU:0:12:0:2 refer to 001200 slot=2 which is sectorA RBS3206. Reported by Fil(FU) since feeder is supervised by FU} /* Check feeder current */

/* Restart RU. This action will restart both RU & FU */ GRY249> actc 15 restartAuxUnit Call Action restartauxunit on following MOs ? =================================================================================== 15 Equipment=1,RbsSubrack=RU1,RbsSlot=2,AuxPlugInUnit=1 =================================================================================== /* Check if fault clear, otherwise warm restart RBS */ GRY249> acc 0 restart =================================================================================== 0 ManagedElement=1 =================================================================================== Parameter 1 of 1, restartRank (enumRef-RestartRank): Enter one of the following integers: 0:RESTART_WARM, 1:RESTART_REFRESH, 2:RESTART_CO >>> Return value = null TMA DEVICE ANTENNA SYSTEM PROBLEM GRY044> alt Nr of active alarms are: 1 =======================================================================================Date & Time (Local) S Specific Problem Cause Mo-=======================================================================================2007-05-14 13:03:03 M TmaDevice_AntennaSystemProblem antenna_problem SectorAntenna=3,AuxPlugInUnit=1,AscDeviceGroup=1,TmaDeviceSet=1,TmaDevice=1 /* Check if sector taking traffic. If sector taking traffic fault is low priority */ RBS>lt radio RBS>get radio /* Restart ASC, FU, then RU */ GRY044> actc <proxy> restartAuxUnit {Repeat CMD for each unit} /* If alarm remain, VSWR > 1.5? Send field supp*/ /* Check Feeder current, short ckt? If yes send field supp to investigate */ /* Check TMA, if faulty replace ASC */ GRY044> lhsh 001200/port_9_dev_15 asc lnaerr {check TMA} LNA transistors branch A OK LNA transistors branch B OK /* End Of Procedure */ MGW /* list all locked/disabled MTP3B */ MGW> lt mtp3b operationalstate==0 OR administrativestate==0 MGW> lget mtp3b userlabel /* list all locked/disabled ETM */ MGW> ltc etm operationalstate==0 OR administrativestate==0 {Load Proxys for MOs and alsubsequent children using the attribute Filter specified} MGW> lst etm /* list all locked/disabled PlugInUnit */ 3GR2> ltc plug operationalstate==0 OR administrativestate==0 3GR2> lst plug /* Check MGW application & fan Unit */ MGW> lt mgw MGW> lst mgw =================================================================================== Proxy Adm State Op. State MO

=================================================================================== 81 1 (UNLOCKED) 1 (ENABLED) MgwApplication=1,Vmgw=1 82 1 (UNLOCKED) 1 (ENABLED) MgwApplication=1,Vmgw=2 83 1 (ENABLED) MgwApplication=1 84 1 (UNLOCKED) 1 (ENABLED) Equipment=1,Subrack=6,MgwFan=GMSE2 85 1 (UNLOCKED) 1 (ENABLED) Equipment=1,Subrack=5,MgwFan=GMSE1 86 1 (UNLOCKED) 1 (ENABLED) Equipment=1,Subrack=3,MgwFan=MSE1 87 1 (UNLOCKED) 1 (ENABLED) Equipment=1,Subrack=2,MgwFan=ATM 88 1 (UNLOCKED) 1 (ENABLED) Equipment=1,Subrack=1,MgwFan=Main =================================================================================== /* Check TDM based term group */ MGW> lt tdm MGW> lst tdm =================================================================================== Proxy Adm State Op. State MO =================================================================================== 89 1 (UNLOCKED) 1 (ENABLED) MgwApplication=1,TdmTermGrp=97 90 1 (UNLOCKED) 1 (ENABLED) MgwApplication=1,TdmTermGrp=95 91 1 (UNLOCKED) 1 (ENABLED) MgwApplication=1,TdmTermGrp=94 92 1 (UNLOCKED) 1 (ENABLED) MgwApplication=1,TdmTermGrp=93 93 1 (UNLOCKED) 1 (ENABLED) MgwApplication=1,TdmTermGrp=92 94 1 (UNLOCKED) 1 (ENABLED) MgwApplication=1,TdmTermGrp=91 95 1 (UNLOCKED) 1 (ENABLED) MgwApplication=1,TdmTermGrp=90 96 1 (UNLOCKED) 1 (ENABLED) MgwApplication=1,TdmTermGrp=89 /* Check block/disabled TDM term grp & in which etm board */ MGW> lt tdm operationalstate==0 OR administrativestate==0 MGW> lget tdm ds0BundleMoRef 070517-17:06:07 172.24.12.205 7.0 RESTRICTED MGW_NODE_MODEL_R3_17_0 stopfile=/tmp/20170=======================================================================================MO Attribute Value =======================================================================================TdmTermGrp=97 ds0BundleMoRef Subrack=3,Slot=23,PlugInUnit=1,Etmc41=1,Os155SpiTtp=MSE1-1,Vc4Ttp=1,Vc12Ttp=28,E1Ttp=1,Ds0Bundle=MSE1-23-1-28 /* Check SignallingRouteSet(SRS). MO SRS has an attribute called destpointcode. SRS hastwo child objects called signallingRoute. The same parent-child relation applies to SignallingLinkSet & Signalling links*/ 3GJ1> lt mtp3bsrs 3GJ1> lget mtp3bsrs destpointcode 1170 {assuming DPC is known, find the SRS label} 070609-19:24:18 172.30.204.31 7.0 RESTRICTED MGW_NODE_MODEL_R3_17_0 stopfile=/tmp/22375=======================================================================================MO Attribute Value =======================================================================================Mtp3bSpItu=MGWNI2,Mtp3bSrs=2-1170 destPointCode 1170 ======================================================================================= 3GJ1> pr Mtp3bSrs=2-1170 {and note the proxy ID} 3GJ1> lcc <proxy_ID> 3GJ1> lst Mtp3bSrs=2-1170 {or lst <proxy_ID>} 070609-19:25:32 172.30.204.31 7.0 RESTRICTED MGW_NODE_MODEL_R3_17_0 stopfile=/tmp/22375=================================================================================== Proxy Adm State Op. State MO =================================================================================== 142 1 (ENABLED) TransportNetwork=1,Mtp3bSpItu=MGWNI2,Mtp3bSrs=2-1170 206 1 (ENABLED) TransportNetwork=1,Mtp3bSpItu=MGWNI2,Mtp3bSrs=2-1170 207 1 (ENABLED) TransportNetwork=1,Mtp3bSpItu=MGWNI2,Mtp3bSrs=2-1170=================================================================================== SECTOR DISABLED RNC NO ALARM

/* You found sector in disabled state from output of str CMD. No utrancell alarm in RNCalarm in RBS */ GRY533> alt =======================================================================================Date & Time (Local) S Specific Problem Cause Mo-=======================================================================================2007-05-23 19:32:08 M AiDevice_ExternalUnitFailure equipment_malfunction RbsSubrack=FU1,RbsSlot=6,AuxPlugInUnit=1,FuDeviceGroup=1,AiDeviceSet=1,AiDevice=2 >>> Total: 1 Alarms (0 Critical, 1 Major) /* Restart FU */ GRY533> actl 17 070524-00:45:42 10.230.17.49 7.0 RESTRICTED RBS_NODE_MODEL_H_6_6 stopfile=/tmp/20638 =======================================================================================Proxy MO Action Nr of Params =======================================================================================17 RbsSubrack=FU1,RbsSlot=6,AuxPlugInUnit=1 reconfigureProgramPrepare 0 17 RbsSubrack=FU1,RbsSlot=6,AuxPlugInUnit=1 restartAuxUnit 0 =======================================================================================GRY533> actc 17 restartAuxUnit 070524-00:45:51 10.230.17.49 7.0 RESTRICTED RBS_NODE_MODEL_H_6_6 stopfile=/tmp/20638 Call Action restartauxunit on following MOs ? =================================================================================== 17 Equipment=1,RbsSubrack=FU1,RbsSlot=6,AuxPlugInUnit=1 =================================================================================== Are you Sure [y/n] ? y =======================================================================================Proxy MO Action Nr of Params =======================================================================================17 RbsSubrack=FU1,RbsSlot=6,AuxPlugInUnit=1 restartAuxUnit 0 >>> Return value = null /* Restart RU if fault remain */ GRY533> actc 14 restartAuxUnit /* alm cleared after RU restart but sector remain down. Check VSWR,lnaerr, & feeder curshould almost equal both branches. If all OK, restart nodeB */ /* Warm Restart nodeB, sector up, End-Of-Procedure*/ CELL RELATIONS RNC> lt gsmrelation|utranrelation 3RR02> pr utranrelation=GRY781 {print proxy of UTRAN relation} 070527-22:01:30 172.24.12.208 7.0 RESTRICTED RNC_NODE_MODEL_F_5_2 stopfile=/tmp/9214 =================================================================================== Proxy MO =================================================================================== 5125 RncFunction=1,UtranCell=GRY382A,UtranRelation=GRY781B 5126 RncFunction=1,UtranCell=GRY382A,UtranRelation=GRY781C 5605 RncFunction=1,UtranCell=GRY781A,UtranRelation=GRY781A_GRY490A 5606 RncFunction=1,UtranCell=GRY781A,UtranRelation=GRY781A_GRY490B 5607 RncFunction=1,UtranCell=GRY781A,UtranRelation=GRY781A_GRY490C 5608 RncFunction=1,UtranCell=GRY781A,UtranRelation=GRY781A_GRY762B 5609 RncFunction=1,UtranCell=GRY781A,UtranRelation=GRY781A_GRY763A 5610 RncFunction=1,UtranCell=GRY781A,UtranRelation=GRY781A_GRY781B 5611 RncFunction=1,UtranCell=GRY781A,UtranRelation=GRY781A_GRY781C 5612 RncFunction=1,UtranCell=GRY781A,UtranRelation=GRY781A_GRY840A 5613 RncFunction=1,UtranCell=GRY781A,UtranRelation=GRY781A_GRY840C 5614 RncFunction=1,UtranCell=GRY781A,UtranRelation=GRY781A_GRY841A 5615 RncFunction=1,UtranCell=GRY781A,UtranRelation=GRY781A_GRY942A 5616 RncFunction=1,UtranCell=GRY781A,UtranRelation=GRY781A_GRY299A AND

3RR02> pr gsmrelation=GRY781 {print proxy of GSM relation} 070527-22:02:14 172.24.12.208 7.0 RESTRICTED RNC_NODE_MODEL_F_5_2 stopfile=/tmp/9214 =================================================================================== Proxy MO =================================================================================== 3247 RncFunction=1,UtranCell=GRY781A,GsmRelation=GRY781A_URI948A 3248 RncFunction=1,UtranCell=GRY781A,GsmRelation=GRY781A_URY049B 3249 RncFunction=1,UtranCell=GRY781A,GsmRelation=GRY781A_URY781A 3250 RncFunction=1,UtranCell=GRY781A,GsmRelation=GRY781A_ZRY049C 3251 RncFunction=1,UtranCell=GRY781A,GsmRelation=GRY781A_ZRY299B 3252 RncFunction=1,UtranCell=GRY781A,GsmRelation=GRY781A_ZRY781A 3253 RncFunction=1,UtranCell=GRY781B,GsmRelation=GRY781B_URY246B 3254 RncFunction=1,UtranCell=GRY781B,GsmRelation=GRY781B_URY793C 3255 RncFunction=1,UtranCell=GRY781B,GsmRelation=GRY781B_ZRI948C 3256 RncFunction=1,UtranCell=GRY781B,GsmRelation=GRY781B_ZRI982A 3257 RncFunction=1,UtranCell=GRY781B,GsmRelation=GRY781B_ZRY246A 3258 RncFunction=1,UtranCell=GRY781B,GsmRelation=GRY781B_ZRY246B 3259 RncFunction=1,UtranCell=GRY781B,GsmRelation=GRY781B_ZRY246C NODE SYNC TP THRESHOLD EXCEEDED /* If alarm is reported for 1 nodeB, most likely it is a hardware fault in the nodeB. Oin nodeB, right-click CBU & perform TU Switch, action will fail anyway b’coz only 1 TU available. Check if alarm cleared, else send tech to check CBU */ 3RJ01> alt =======================================================================================Date & Time (Local) S Specific Problem Cause Mo-=======================================================================================2007-06-01 19:35:10 M NodeSynchTp_Threshold_Exceeded threshold_crossed IubLink=Iub_GNJ307,NodeSynchTp=1 >>> Total: 6 Alarms (1 Critical, 3 Major) 3RJ01> lst gnj307 =================================================================================== Proxy Adm State Op. State MO =================================================================================== 5935 1 (UNLOCKED) 1 (ENABLED) RncFunction=1,IubLink=Iub_GNJ307,NodeSynchTp=2 5936 1 (UNLOCKED) 1 (ENABLED) RncFunction=1,IubLink=Iub_GNJ307,NodeSynchTp=1 =================================================================================== Total: 20 Mos 3RJ01> get 5935 5936 =======================================================================================5935 RncFunction=1,IubLink=Iub_GNJ307,NodeSynchTp=2 =======================================================================================NodeSynchTpId 2 aal0TpRefs [1] = >>> aal0TpRefs = TransportNetwork=1,Aal0TpVccTp=b2068sb1 administrativeState 1 (UNLOCKED) availabilityStatus 0 (NO_STATUS) nodeSynchRef IubLink=Iub_GNJ307,NodeSynch=1 operationalState 1 (ENABLED) timDeviceRef Subrack=MS,Slot=5,PlugInUnit=1,TuDeviceGroup=1,TimDeviceSet=1,TimDevice=1 userLabel 2 =======================================================================================5936 RncFunction=1,IubLink=Iub_GNJ307,NodeSynchTp=1

==============================================================================NodeSynchTpId 1 aal0TpRefs [1] = >>> aal0TpRefs = TransportNetwork=1,Aal0TpVccTp=b2068sa1 administrativeState 1 (UNLOCKED)

availabilityStatus 64 (DEGRADED) nodeSynchRef IubLink=Iub_GNJ307,NodeSynch=1 operationalState 1 (ENABLED) timDeviceRef Subrack=MS,Slot=4,PlugInUnit=1,TuDeviceGroup=1,TimDeviceSet=1,TimDevice=1 userLabel

APPENDIX A: IMA TROUBLESHOOTING GUIDE RETURN

IMA Node B Troubleshooting Guide

1. NSC Op’s to verify node b is an IMA/HSDPA site via list in shared folder. 2. If node b is IMA enabled/HSDPA, trouble ticket to be indicated of this and informed to

RANO. 3. Upon 1.5hr’s of outage, trouble ticket MUST be escalated to EOT NSS Utran Support

team. 4. EOT NSS Utran Support to be informed that this node b is IMA/HSDPA enabled. 5. RANO & EOT NSS Utran Support to be informed that within 3hr’s of outage, CSR MUST

be created. 6. NSC Op’s has to ensure that RANO and E/// Field Support personnel’s can only leave site

once site is up & operational (regardless of software level P3/P4).

Alarm Troubleshooting Step’s

1. E1 status of node b to be checked via step’s in moshell as below : “LOOK OUT FOR THE IMAGROUP ALARM AS INDICATED/HIGHLIGHTED BELOW TO ENSURE SITE IS IMA/HSDPA ENABLED” Example : ET-14-22 connected to RXIKPNG02) RXIKPNG02> lst ImaGroup=MS-14-ima22 060721-17:19:44 10.78.64.97 6.1zt CPP_MOM_MOM-CPP_4.3.3-1_0 stopfile=/tmp/25696 =================================================================================== Proxy Adm State Op. State MO =================================================================================== 5633 1 (ENABLED) TransportNetwork=1,ImaGroup=MS-14-ima22 5634 1 (ENABLED) TransportNetwork=1,ImaGroup=MS-14-ima22,ImaLink=3 5635 1 (ENABLED) TransportNetwork=1,ImaGroup=MS-14-ima22,ImaLink=2 5636 1 (ENABLED) TransportNetwork=1,ImaGroup=MS-14-ima22,ImaLink=1 =================================================================================== Total: 4 MOs RXIKPNG02> get 5634 060721-17:19:49 10.78.64.97 6.1zt CPP_MOM_MOM-CPP_4.3.3-1_0 stopfile=/tmp/25696 ======================================================================================= 5634 TransportNetwork=1,ImaGroup=MS-14-ima22,ImaLink=3 ======================================================================================= ImaLinkId 3 availabilityStatus 0 (NO_STATUS) operationalState 1 (ENABLED) userLabel uses Subrack=MS,Slot=14,PlugInUnit=1,Etmc41=1,Os155SpiTtp=pp1,Vc4Ttp=1,Vc12Ttp=24,E1Ttp=1

======================================================================================= Total: 1 MOs RXIKPNG02> get 5635 060721-17:19:52 10.78.64.97 6.1zt CPP_MOM_MOM-CPP_4.3.3-1_0 stopfile=/tmp/25696 ======================================================================================= 5635 TransportNetwork=1,ImaGroup=MS-14-ima22,ImaLink=2 ======================================================================================= ImaLinkId 2 availabilityStatus 0 (NO_STATUS) operationalState 1 (ENABLED) userLabel uses Subrack=MS,Slot=14,PlugInUnit=1,Etmc41=1,Os155SpiTtp=pp1,Vc4Ttp=1,Vc12Ttp=23,E1Ttp=1 ======================================================================================= Total: 1 MOs RXIKPNG02> get 5636 060721-17:19:59 10.78.64.97 6.1zt CPP_MOM_MOM-CPP_4.3.3-1_0 stopfile=/tmp/25696 ======================================================================================= 5636 TransportNetwork=1,ImaGroup=MS-14-ima22,ImaLink=1 ======================================================================================= ImaLinkId 1 availabilityStatus 0 (NO_STATUS) operationalState 1 (ENABLED) userLabel uses Subrack=MS,Slot=14,PlugInUnit=1,Etmc41=1,Os155SpiTtp=pp1,Vc4Ttp=1,Vc12Ttp=22,E1Ttp=1 ======================================================================================= Total: 1 MOs

2. Group E1 & individual E1’s connected to site is checked & verified for operational status 3. If individual E1 is in DISABLE status, routine transmission check is performed.

Alarm as below would be detected at RXI : (Example : ET-14-22 connected to RXIKPNG02) Loss of Cell Delineation on IMA Link @ local_node_transmission_error @ ImaGroup=MS-14-ima22,ImaLink=1 Loss of Cell Delineation on IMA Link @ local_node_transmission_error @ ImaGroup=MS-14-ima22,ImaLink=2 Loss of Cell Delineation on IMA Link @ local_node_transmission_error @ ImaGroup=MS-14-ima22,ImaLink=3

RXIKPNG02> lst ImaGroup=MS-14-ima22 060721-17:19:44 10.78.64.97 6.1zt CPP_MOM_MOM-CPP_4.3.3-1_0 stopfile=/tmp/25696 =================================================================================== Proxy Adm State Op. State MO =================================================================================== 5633 1 (ENABLED) TransportNetwork=1,ImaGroup=MS-14-ima22 {Ima Group} 5634 1 (ENABLED) TransportNetwork=1,ImaGroup=MS-14-ima22,ImaLink=3 {Ima Link} 5635 1 (ENABLED) TransportNetwork=1,ImaGroup=MS-14-ima22,ImaLink=2 {Ima Link} 5636 1 (ENABLED) TransportNetwork=1,ImaGroup=MS-14-ima22,ImaLink=1 {Ima Link} =================================================================================== Total: 4 MOs

REMARK - Highlighted in yellow is the E1 for node b. Check for operational status enable/disable.

4. If Group E1 is in DISABLE status, below step’s are taken to verify the affected ET-MC41 board in respective RXI for operational status.

Alarm as below would be detected at RXI :

(Example : ET-14-22 connected to RXIKPNG02) IMA Group Insufficient Links @ local_node_transmission_error @ ImaGroup=MS-14-ima22 IMA Group Insufficient Links at Far End @ remote_node_transmission_error @ ImaGroup=MS-14-ima22

RXIKPNG02> lst ImaGroup=MS-14-ima22 060721-17:19:44 10.78.64.97 6.1zt CPP_MOM_MOM-CPP_4.3.3-1_0 stopfile=/tmp/25696 =================================================================================== Proxy Adm State Op. State MO =================================================================================== 5633 1 (ENABLED) TransportNetwork=1,ImaGroup=MS-14-ima22 5634 1 (ENABLED) TransportNetwork=1,ImaGroup=MS-14-ima22,ImaLink=3 5635 1 (ENABLED) TransportNetwork=1,ImaGroup=MS-14-ima22,ImaLink=2 5636 1 (ENABLED) TransportNetwork=1,ImaGroup=MS-14-ima22,ImaLink=1 =================================================================================== Total: 4 MOs

REMARK - Highlighted in yellow is the Group E1 for node b. Check for operational status enable/disable.

ELS Recommendation Moshell into affected RXI, and key in command “lhsh XX XX XX te log read” XX XX XX – Affected ET-MC41 board in RXI

If alarm “Aet_iworxDrvAtm_proc iworxatm…………………….Loopbacktimeout (5s)” this indicates ET-MC41 board has hang & restart of board need to be performed.

APPENDIX B: MOSHELL & UTILITY COMMANDS SHELL UTILITY COMMANDS UNIX_PROMPT> ./mobatch Usage: mobatch.pl [options] <sitefile> <command(s)>|<commandfile>|<commanddir> [logdirectory] Purpose: To send moshell commands to several nodes in parallel. Arguments: - The first argument is the sitefile, containing IP/DNS addresses and/or site names whose IP address are defined in the IP database.See example of sitefile in: moshell/examples/sitefiles/. See example of ipdatabase in: moshell/examples/ipdatabase/ - The second argument is the commmand or commandfile. See example of commands below. See example of commandfile in moshell/examples/mobatch_cmdfiles. If a directory is given, then a different commandfile will be used for each node: the name of each commandfile should be <node-name>.cmd or <node-name>.mos. the <node-name> should be the same as given in the sitefile. example: node-name is rbs602 ==> commandfile should be rbs602.cmd or rbs602.mos - The third argument (logdirectory) is optional. If no logdirectory is specified, a default one will be used. Options: - t <minutes> Specify the number of minutes before timing out. Set to 0 for no timeout (default=20). - p <processes> Specify the maximum number of moshell sessions that will run in parallel (default=10)

- v <userVariables> Specify moshell uservariables. Type "moshell" on its own for more info about this option. Examples: mobatch -p 15 -t 60 ~/sitefiles/victoria-sites 'lt all ; get' mobatch ./sitefiles/all-rbs.txt ./cmdfiles/do_healthCheck.mos mobatch -p 5 -t 1 ./sitefiles/all-rbs.txt 'cv cu ; rbs' mobatch ./sitefiles/all-rnc.txt 'lt ^utrancell ; st cell' mobatch ./sitefiles/all-bsc.txt ~/bsc-commandfiles/ mobatch -v security_method=2,sa_credential=~/sam.pbe,sa_password=oemas -p 20 ./all_mgw.txt 'hc' mobatch -v ip_database=~/utran_network/ipdatabase ~/utran_network/ipdatabase 'lt all ; get ' UNIX_PROMPT> ./rncaudit *************** Command Syntax: *************** rncaudit <Options> <Argument> ******** Options: ******** -a <changeAll_file> Where <changeAll_file> is a Ranos Change_All script. -b <baseline_file> Where <baseline_file> is a parameter list derived from Winnow database. See example in moshell/examples/audit_files/baseline.txt This file can be directly exported from the following excel documents: n/19059-HSD10102/m, where: n=3 for RNC m=3 for P3 n=4 for RBS m=4 for P4 n=5 for RXI m=5 for P5 To compare against a change all script, convert the change_all script to baseline format using the "mocmd" utility. -c <cdr_file> Where <cdr_file> is a file containing cell data (UtranCell, Fach, Rach, Pch). See example in moshell/examples/audit_files/CDR_celldata.txt -r <utranrelation_file>. Where <utranrelation_file> is a file containing a list of all utranrelations. See example in moshell/examples/audit_files/CDR_utranrelations.txt -u <uerc_file> Where <uerc_file> is a file containing "SET" commands for uerc data (delivered by RAN PU).See example in moshell/examples/audit_files/UeRc_CXC1326348_R8D02.mo -i Consistency check of internal utranrelations, ie, that they are going both ways and that all utranrelations appear in the "reservedBy" list of the UtranCells they are pointing to. -e Consistency check of external utranrelations, ie, that they are going both ways and that the ExternalUtranCell attributes match the UtranCell attributes they are referring to. This option only works when the logdirectory containing all RNC dumps is given as argument. -s Check for duplicated Scrambling Codes in Cell neighbour lists. Checks first tier, second tier and third tier collisions. -o <outputdir> Specifies the output directory that will be used (if none is specified then a default will be used).

Note1: Options "-i" and "-e" should not be run before the nodes' data are consistent with the CDR file and UtranRelation file. This means that options "-c" and "-r" should be run first, necessary parameter corrections should be applied to the nodes, new modumps should be taken from the nodes, and the check can be run using options "-i", "-e". The "-s" option should only be run once all other checks have been done and corrections made. More information in document moshell/examples/audit_files/Audit_procedure_A1.doc Note2: By copying columns 1,2 and 4 from the result file into a text file and running it through the utility "mocmd" (located in moshell directory), it is possible to generate a corrective script to be run with moshell/monode or mobatch. Note3: When running "-b" simultaneously with "-a" and/or "-u", a message is printed if some attributes are checked both in the baseline and one of the other files. The value specified in baseline takes precedence. ********* Argument: ********* - directory containing the modumps OR: - modump file Modumps should be taken with mobatch or monode, using command: moshell <ip_address> 'ltc rncfunction;get' (for dumping one node) OR: mobatch <rnc_sitefile> 'ltc rncfunction;get' (for dumping several nodes in parallel) ******** Example: ******** >> rncaudit -b ./examples/audit_files/baseline.txt \ -c ./examples/audit_files/CDR_celldata.txt \ -r ./examples/audit_files/CDR_utranrelations.txt \ -u ./examples/audit_files/UeRc_CXC1326348_R8D02.mo \ ./logfiles/logs_mobatch/030630-1830_allRnc/ Make all required corrections on the nodes, take new modumps, then: >> rncaudit -ie ./logfiles/logs_mobatch/030705-1810_allRnc/ 2.0 MOSHELL HELP 0- Installation, security, and user settings 1- Revision History 2- Tutorial 3- Command syntax, regular expressions 4- Command descriptions 5- Lazy 6- Scripting 7- Utilities 8- Server Maintenance 9- Offline Mode Enter section number: 4 {This line contain Bookmark, do not delete} - !/l <unix command> - <ose command> [|<unix command>] (type "h ose" for info) - acc/lacc - acl/lacl - al[atk] - alias/unalias - b - bl[s]/lbl[s] - bo[r]/ba[s]/baw[s]/bad/br/brw/brd/bp - cab[slxradgt] - col - conf[bld] - cr

- ctrl-z ; touch /tmp/xxxx;fg (abort MO command, type "h ctrl-z" for info) - cvls/cvmk/cvms/cvset/cvrm/cvcu - cvls1 - d2ip - deb/ldeb - del/ldel - diff/ldiff - edit - emom - facc/lfacc - fclean[f|ff|d|e] - fget/lfget - flt/fltc - fro/lfro[m] - fset/lfset - ftget[c]/ftput[c] - ftree - get/lget - getmom - gs/gsg - h2d/d2h - hc - hget[c]/lhget[c] - hi [<commandFilter>], !<commandNr> - hpget[c]/lhpget[c] - htget - inv[hr] - ip2d - kget/lkget - l+[m][m][s][o]/l-/l? - lc[1-9]/lcc - ld - lg[<options>] - lh - lk/llk - lki - lko/llko - lmid[c] - lt/ltc[1-9] - ma/lma - mom[tc]/pmom[c]/lmom[c] - mon+/mon-/mon?/mon - mp - mr/lmr - noload[+/-] - p/w/pw/b - parsemom - pbl - pcr[cfd] - pdeb - pdel - pget/lpget - pgets[n] - pgu[c][f] - pme[fd][cgu] - pmr[ag] - pmx[hfdn] - pol[s] - pr/lpr - print - prod - prox - pset[d] - pst - pv/printvars - q/by/exit/quit - rdel/lrdel - re[i] - remod[u][2] - return - rset/lrset - run - set[m]/lset[m] - sget/lsget - sql+/sql-/sql? - st/lst - stc[r] - std - str - tg[r][c][d] - trun[i] - u+[s]/u-/u? - uer - ul - uv/uservars - wait Type: h <command> to view command description. E.g: h pget ####################################################################################

Tutorial #################################################################################### ################################ 2.1- MO concept ################################ (reference: 11/1551-CSX10109 O&M system principles in a cello node) **************************************** | O&M Client | | (eg: EMAS/OE/RANOS/moshell,etc.) | **************************************** | | **************************************** | CS,PM,AL,NS,IS,LS Service Layer | ****************************************

| | **********|****************************** * +++++++ * * | | * * | MAO | Management Adaption Layer* * | | * MO--> * | | ------------------------ * * | FRO | * * | | Resource Layer * * | RO | * * | | * * +++++++ * ***************************************** The O&M client can access the MOs through a number of services: * Configuration Service (CS): to read and change configuration data. Configuration data is stored in the MO attributes. * Performance Measurement (PM): to setup statistics scanners or event filters. The statistics counters are stored in MO pm-attributes and output to an XML file every 15 minutes. The events are output into binary files every 15 minutes. * Alarm Service (AS): to retrieve the list of alarms currently active on each MO. * Notification Service (NS): to subscribe and receive notifications from the node, informing about parameter/alarm changes in the MOs. * Inventory Service (IS): to get a list of all HW and SW defined in the node. * Log Service (LS): to save a log of certain events such as changes in the configuration, alarms raising and ceasing, node/board restarts, jvm events, O&M security events, etc The MO is a way of modelling resources in a Cello node. It consists of: 1) a Management Adaption Layer which is implemented in java, in the MP running the jvm (the O&M MP). The purpose of the MAO (Management Adaptation Object) is to interface towards the various O&M services described above. 2) a Resource Layer consisting of Facade Resource Object (FRO) and a Resource Object (RO) which are implemented in C and run on the various boards. The RO is the actual resource modelised by the MO. The purpose of the FRO is to act as an interface between the MAO and the RO, by handling the configuration transactions and storing configuration data for the RO. ################################ 2.2- O&M services and protocols ################################ OSE-shell File-Service MO-Services | | | | | | | | | +++++++++++++++++++++++++++++++++++++ | |ssh/telnet| ftp/http | iiop(corba) | | +++++++++++++++++++++++++++++++++++++ | | TCP/IP | | +++++++++++++++++++++++++++++++++++++ RS232 | Ethernet/IPoATM | +++++++++++++++++++++++++++++++++++++ The MO services described above (CS, AS, PM, IS, NS) are carried by the IIOP protocol (Internet Inter-ORB Protocol), also called CORBA (Common Object Request Broker Architecture). At startup, the node generates its IOR (Interoperable Object Reference) and stores it in a "nameroot.ior" file which can be used by the O&M client to access the node. The IOR file contains the node's IP address and some specifications as to how the clients can send requests to the node.

The OSE-shell (also called COLI) can be accessed through telnet/ssh or locally, through the serial port (RS232). It gives direct access to the operating system, the file system, and parts of the FRO/RO layer. OSE shell commands are described in the document 1553-CXA 104 203. ################################ 2.3- MO tree ################################ a- LDN: The MOs are organised in a hierarchical structure. Each MO instance is uniquely identified in the node by its Local Distinguished Name (LDN). The highest MO in a node ("root MO") is the ManagedElement, which is an MO representing the whole node. There is only one instance of the ManagedElement MO in the node and it is referenced by the LDN: "ManagedElement=1". The string at the left of the equal sign is called the MO class (or MO type) and the string at the right of the equal sign is called the MO identity. In the case of the root MO, the MO class is "ManagedElement" and the identity is "1". If an MO is located further down in the MO tree, the LDN must contain the MO classes and identities of all the parents of that MO, in a sequence going from the root MO down to the MO in question. See example below: ManagedElement=1 ManagedElement=1,Equipment=1 ManagedElement=1,Equipment=1,Subrack=MS ManagedElement=1,Equipment=1,Subrack=MS,Slot=19 ManagedElement=1,Equipment=1,Subrack=MS,Slot=19,PlugInUnit=1 ManagedElement=1,Equipment=1,Subrack=MS,Slot=19,PlugInUnit=1,Program=DbmFpgaLoader From this example, we can see that the ManagedElement has a child called "Equipment=1" which has a child called "Subrack=MS" (representing the main subrack of the node), which has a child called "Slot=19" (representing the slot in position 19), which has a child called "PlugInUnit=1" (representing the board located in that slot), which has a child called "Program=DbmFpgaLoader" (representing one of the programs loaded in that board). The LDN of the lowest MO (the one called "Program=DbmFpgaLoader") contains the address of all successive parents of that MO all the way up to the ManagedElement. b- RDN: The string located at the far right of an LDN, just after the last comma, is called a Relative Distinguished Name (RDN). It is a unique way of addressing an MO instance in relation to its closest parent. This means that there is only one MO instance with the RDN "Program=DbmFpgaLoader" under the parent MO "ManagedElement=1,Equipment=1,Subrack=MS,Slot=19,PlugInUnit=1". However, there could be another MO instance with the same RDN under a different parent MO. For instance, there could be an MO instance with the RDN "Program=DbmFpgaLoader" under the parent MO "ManagedElement=1,Equipment=1,Subrack=MS,Slot=23,PlugInUnit=1". Therefore the RDN is a relative way of addressing an MO instance. c- FDN: When a node is connected to a Network Management System such as OSS, there is a need to uniquely address each MO within the whole network. The Full Distinguished Name (FDN) adds a network element prefix in front of the LDN of each MO instance in order to specify which node this MO belongs to. See the figure below, summing up the FDN/LDN/RDN concept: FDN (Full Distinguished Name) <------------------------------------------------------------..............................................................> LDN (Local Distinguished Name) <--------------..................................................................> MoClass Identity <-----> <---> RDN (Relative Distinguished Name) <----------> Network=H3GA,Utran=Rnc1,MeContext=Rbs03,ManagedElement=1 RDN <--------> Network=H3GA,Utran=Rnc1,MeContext=Rbs03,ManagedElement=1,Equipment=1 RDN

<--------> Network=H3GA,Utran=Rnc1,MeContext=Rbs03,ManagedElement=1,Equipment=1,Subrack=MS RDN Network=H3GA,Utran=Rnc1,MeContext=Rbs03,ManagedElement=1,Equipment=1,Subrack=MS,Slot=19 <--------> RDN Network=H3GA,Utran=Rnc1,MeContext=Rbs03,ManagedElement=1,Equipment=1,Subrack=MS,Slot=19,PlugInUnit=1 <-----------------> Network=H3GA,Utran=Rnc1,MeContext=Rbs03,ManagedElement=1,Equipment=1,Subrack=MS,Slot=19,PlugInUnit=1,Program=DbmFpgaLoader ################################ 2.4- MOM - Managed Object Model ################################ Each MO class contains a number of attributes which are used to store configuration data or performance measurement data. Each MO class can also support a number of defined actions which will cause the MO to perform certain operations: a typical example is the action "restart" which will cause the MO to restart the resource it is responsible for (a board, a program, etc.). The Managed Object Model (MOM) is a reference document describing all the MO Classes that can exist in a node, together with their attributes and actions. The format of the MOM can be UML, XML, HTML, or MS-Word. The XML version of the MOM is usually stored on the web server of the node at the address http://<ipaddress>/cello/oe/xml/<filename>.xml The MOMs for each SW release are also stored in HTML format on a number of web sites: - Cello MOMs: http://techdev.uab.ericsson.se/~eraakpa/ - RNC MOMs: http://wrn.ericsson.se/~emogroup/mom/ - RBS MOMs: http://wrn.ericsson.se/~enrbsmom/mom/ ################################ 2.5- MoShell functionality ################################ MoShell is a text-based O&M client providing access to the following services: - Configuration service (CS) - Alarm service (AS) - Performance management service (PM) - Log service (LS) - OSE shell (COLI) - File transfer (ftp/http) Access to all services is supported both in secure mode (secure Corba, ssh, sftp) and unsecure mode (unsecure corba, telnet, ftp). a- Alarm Service The list of active alarms can be retrieved with the commands "al" or "ala". (al shows an overview whereas ala shows all the details). b- OSE shell Any OSE shell command can be typed at the moshell prompt and the output can be piped through external utilities if required. Examples: > te log read > te log read | grep ERROR Limitations: Only the "$" prompt is supported. For instance, it is not possible to type "lhsh 000100" and expect a prompt to that board.

The workaround is to type the command on the same line as the link handler shell, eg "lhsh 000100 te log read" or put a semicolon after the "lhsh xxxx", eg "lhsh 001400 ; te log read ; vii ; llog ". Type "h ose" at the moshell prompt for more info. c- Configuration Service Moshell supports the following 6 operations from the configuration service: * GetChildren : to load all or parts of the MO-tree * GetAttribute : to read the attributes of an MO * CallAction : to perform an action on an MO * SetAttribute : to set (change) the value of an MO attribute * CreateMO : to create a new MO in the node * DeleteMO : to delete an MO from the node d- Performance Management Service Moshell supports the following operations from the performance management service: * List Scanners and Event Filters * Create Scanner * Stop Scanner * Resume Scanner * Delete Scanner * Set Event Filter e- Log service Moshell supports fetching and parsing of the following logs: * availability log * system log * event log * alarm log * command log * O&M security event log * COLI log * hw inventory log * jvm events log (upgrade log) f- File transfer Moshell can download/upload files and directories to/from the node, using http, ftp, or sftp. ################################ 2.6- Getting started ################################ An moshell session is started from the unix shell prompt, using command: "moshell <node's ip-address>" Upon startup, moshell will go through the following steps: 1- download the node's IOR file and store it on the workstation. The node's IOR file is fetched from http://nodeipaddress/cello/ior_files/nameroot.ior 2- check the node's MOM version. The node's MOM is fetched from http://nodeipaddress/cello/oe/xml/<filename> where <filename> is one of the files listed in the user variable xmlmomlist. The MOM version is derived from the "mim" tag inside the MOM file, eg: <mim name="RNC_NODE_MODEL_E" version="5" release="3"> becomes RNC_NODE_MODEL_E_5_3. If this MOM version does not exist on the workstation (under moshell/jarxml directory), then it is downloaded from the node and stored in that directory. If the MOM version could not be figured out (ie. moshell could not find any MOM on the node), the MOM specified in the moshell uservariable default_mom is used. 3- parse the MOM and generate an internal table specifying all MO classes, attributes, and actions supported by the node. 4- initiate Corba communication with the node by using the information contained in the IOR file. 5- read the FDN of the root MO 6- ready to receive commands from the user

At this stage, it is possible to access the alarm service and OSE shell but the configuration service is limited since moshell doesn't have any knowledge of what MO instances are contained in the node's MO tree (apart from the root MO). The whole MO tree can be read with command "lt all". The LDN of each MO of the MO tree is then allocated a "proxy" number and stored in an internal table in moshell memory. The internal proxy table can be printed via the command "pr" which will show for each MO, the LDN and the proxy number. When performing an operation on an MO (get, set, action, etc.), either the proxy number or the LDN can be given as argument. In fact, by using a regular expression matching part of the LDN, an operation can be performed on several MOs at a time. More information about this can be found in chapter 3 or by typing "h syntax" at the prompt. To save memory on the workstation, it is possible to load only parts of the MO tree instead of the whole MO tree. For instance, by typing "lt pluginunit", only the LDNs of MOs whose MO class is "PlugInUnit" will be read. Instead of typing the whole MO class, it is possible to type a regular expression that will match the MO class. In this case, "lt plu" would be the same as "lt pluginunit", since the string "plu" matches "pluginunit". More information about this in chapter 4 or by typing "h lt" and "h lc" at the prompt. To perform operations on one or several MOs, follow the command syntax shown on the menu. Example1: to read the MO attributes of the MO "ManagedElement=1,Equipment=1,Subrack=MS,Slot=19,PlugInUnit=1", just do: > pr plu ---> then lookup the proxy identity of that MO > get <proxy> ---> enter the MO's proxy identity as argument to the "get" command or: > lget ms,slot=19,pluginunit=1$ Example2: to read the MO attributes of all MOs whose MO class is "PlugInUnit", just do: > get plu ---> the get command will operate on all MOs whose RDN matches "plu" More info about this in chapter 3 or by typing "h syntax" at the prompt". Help for each command can be found in chapter 4 or by typing "h <command-name>" at the prompt. !!! Important note for CDMA nodes: Most CDMA nodes do not keep a MOM on the node's harddisk. To force moshell to use the correct MOM, here are some workarounds: * store the correct MOM in your directory moshell/jarxml, then, after the moshell startup, use the command "parsemom <mom>" to parse the correct MOM, or specify the path to this MOM in your "default_mom" user variable (see chap 0.2 for info on user variables). * store the correct MOM on the node at /c/public_html/cello/oe/xml/CelloMOM.xml * check if the node has a MOM that is under a different file name than is specified in the moshell uservariable "xmlmomlist". This can be done by doing "ls /c/loadmodules_norepl" or "ftree /c/loadmodules_norepl" and search for a MOM file (file extension ".xml") ################################ 2.7- Directory structure ################################ The moshell directory contains a number of files and subdirectories: ..../moshell logfiles/ # To store the logfiles generated by the various utililites (moshell, mobatch, swstat, etc.) examples/ # Example of input files required by the utilities (command files, site files, etc.)

cmdfiles/ # Place to store your command files (to be used by mobatch/monode/telbatch/telnode, etc.) sitefiles/ # Place to store your sitefiles (to be used by mobatch/telbatch/swstat/swup, etc.) jarxml/ # Place to store jar files (oms.jar and vbjorb.jar) and xml-MOM files (used by moshell). Specific to certain nodes. commonjars/ # Place to store jar files common to all nodes gawk # Script interpreter used by the various utilities prog.awk,funcs.awk # Main code for moshell, cannot be run on its own. README # Help file rncaudit # Audit and consistency check of rnc data towards cell data CDR, utranrelations CDR, baseline, uerc, etc. moshell # The file used to startup moshell. Contains some customizable variable settings. swstat # To view SW revisions, CV's and delete old upgrade packages rbsaudit # Audit and consistency check of rbs data towards rbs data and baseline. Generation of mobatch corrective scripts. swup # Network SW upgrades mobatch # Run moshell commands on several nodes in parallel cvms # create and set cv's on several nodes in parallel momdoc # convert MOM from xml to html mocmd # generate moshell command file from a baseline parameter file RETURN #################################################################################### Command syntax, regular expressions #################################################################################### ################################################# 3.1- How MOs are identified ################################################# - RDN (Relative Distinguished Name) This is used to identify an MO in relation to its nearest parent in the MO tree. The RDN contains MO Class (also called MO Type), the equal sign, and MO identity. Example: AtmPort=MS-24-1 ==> "AtmPort" is the MO Class, "MS-24-1" is the identity - LDN (Local Distinguised Name) This is used to uniquely identify an MO within a node. The LDN shows the hierarchy above the MO, within the Managed Element's MO tree. Example: ManagedElement=1,TransportNetwork=1,AtmPort=MS-24-1 - FDN (Full Distinguished Name) This is used to uniquely identify an MO within a network (used by RANOS/CNOSS). Example: SubNetwork=AUS,SubNetwork=H2RG_0201,MeContext=St_Leonards_Station_2065010,ManagedElement=1,TransportNetwork=1,AtmPort=MS-24-1 ################################################## 3.2- How to address the MOs in MO-related commands ################################################## The first argument in the MO-related commands is usually used to specify the MOs that should be affected by the command. Six ways can be used to specify the MO(s): 1) all ==> all MOs in the proxy table will be affected Example:

get all userlabel ---> get attribute "UserLabel" on all MOs Note: instead of "all", it is also possible a wildcard such as "." or "*". This has the same effect. 2) proxy id(s) ==> MO(s) with the given proxy id(s) will be affected. To specify several MO proxies, there are two ways: - Specify each proxy id with a space in between Example: pr 0 2 5 --> print MO proxies 0, 2, and 5 - Give a range Example: pr 4-10 --> print MO proxies from 4 to 10 pr 10-4 --> print MO proxies from 10 to 4 (reverse order, useful for deleting MOs) acc 10-20 restart ---> restart MOs with proxy 10 to 20 3) link handler (for pluginunit and spm MOs only) Example: acc 001400 restart ---> to restart the MO Subrack=MS,Slot=14,PlugInUnit=1 bl 001900/sp0.lnh ---> to lock the spm Subrack=MS,Slot=19,PlugInUnit=1,Spu=1,Spm=1 4) mo group ==> MO(s) belonging to the given MO group will be operated upon. To create an MO group, see command description for ma/lma and mr/lmr Note: In RNC, running the "bo" command will automatically create a number of MO groups containing the cc/dc/pdr device MOs for each module. 5) board group ==> MOs (PlugInUnit or Spm) mapped onto the boards belonging to the given board group will be operated upon. Example1: baw sccp sccp ---> all boards with the swallocation matching "sccp" will go into the board group "sccp" bl sccp ---> all PlugInUnit or Spm MOs connected to boards of this board group will be locked Example2: In RNC, using the default board groups created after running the bo command: acc mod10 restart pr dc10 acc dc10 restart (the board group dc10 is mapped onto the Spm MOs) bl dc10dev (in this case we are using the MO group containing the Device MOs, see paragraph 4. above) 6) mo-filter ==> MO(s) whose LDN/RDN match the pattern will be operated upon. If the command starts with "l" then the pattern will match agains the LDN. If the command doesn't start with "l", then the pattern will match against the RDN. Example: >> pr ms-24-1 returns: TransportNetwork=1,AtmPort=MS-24-1 >> lpr ms-24-1 returns: TransportNetwork=1,AtmPort=MS-24-1 TransportNetwork=1,AtmPort=MS-24-1,VplTp=vp1 TransportNetwork=1,AtmPort=MS-24-1,VplTp=vp1,VpcTp=1 TransportNetwork=1,AtmPort=MS-24-1,VplTp=vp1,VpcTp=1,VclTp=vc32 TransportNetwork=1,AtmPort=MS-24-1,VplTp=vp1,VpcTp=1,VclTp=vc33 TransportNetwork=1,AtmPort=MS-24-1,VplTp=vp1,VpcTp=1,VclTp=vc337 TransportNetwork=1,AtmPort=MS-24-1,VplTp=vp1,VpcTp=1,VclTp=vc332 TransportNetwork=1,AtmPort=MS-24-1,VplTp=vp2 TransportNetwork=1,AtmPort=MS-24-1,VplTp=vp2,VpcTp=1 TransportNetwork=1,AtmPort=MS-24-1,VplTp=vp2,VpcTp=1,VclTp=vc34

TransportNetwork=1,AtmPort=MS-24-1,VplTp=vp2,VpcTp=1,VclTp=vc35 TransportNetwork=1,AtmPort=MS-24-1,VplTp=vp2,VpcTp=1,VclTp=vc40 TransportNetwork=1,AtmPort=MS-24-1,VplTp=vp2,VpcTp=1,VclTp=vc64 When using the mo-filter, it is a good idea to test the pattern with "pr/lpr" command before issuing a get/set/acc/cr/del command, in order to see which MOs will be matched by the pattern. Sometimes, a second or third argument can be given, which is usually a string matching the attribute or attribute value that you want to display. The search string that is used in the filters is a Unix Regular Expression (like the patterns used in grep command). Therefore, special meta-characters such as . * [ ] ^ $ can be used. Short description of some meta-characters: "." --> any single character "*" --> 0 or more occurences of the previous character [] --> matches a character or range of characters inside the brackets [^] --> NOT matching a character or range of characters inside the brackets | --> OR ^ --> beginning of string $ --> end of string ! --> negation % --> reverse order E.g: "a*" means a or aa or aaa, etc. ".*" is like a wildcard as it matches 0 or more occurences of any character "[a-z]" matches all letters from a to z "[abe]" matches letters a,b, and e "[^3]" matches any character but not 3 3|5|6 matches 3 or 5 or 6 ^a.*4$ matches a string beginning with a and finishing with 4, with any character in the middle Regular expressions can be grouped using brackets, e.g: "cell(11|23|45) matches cell11 or cell23 or cell45 !!!! Note: MOSHELL pattern matching is NOT case sensitive !!!!! Examples of using regular expressions in the filters: lpr ms-24-1.*vp2 TransportNetwork=1,AtmPort=MS-24-1,VplTp=vp2 TransportNetwork=1,AtmPort=MS-24-1,VplTp=vp2,VpcTp=1 TransportNetwork=1,AtmPort=MS-24-1,VplTp=vp2,VpcTp=1,VclTp=vc34 TransportNetwork=1,AtmPort=MS-24-1,VplTp=vp2,VpcTp=1,VclTp=vc35 TransportNetwork=1,AtmPort=MS-24-1,VplTp=vp2,VpcTp=1,VclTp=vc40 TransportNetwork=1,AtmPort=MS-24-1,VplTp=vp2,VpcTp=1,VclTp=vc64 lpr %ms-24-1.*vp2 TransportNetwork=1,AtmPort=MS-24-1,VplTp=vp2,VpcTp=1,VclTp=vc64 TransportNetwork=1,AtmPort=MS-24-1,VplTp=vp2,VpcTp=1,VclTp=vc40 TransportNetwork=1,AtmPort=MS-24-1,VplTp=vp2,VpcTp=1,VclTp=vc35 TransportNetwork=1,AtmPort=MS-24-1,VplTp=vp2,VpcTp=1,VclTp=vc34 TransportNetwork=1,AtmPort=MS-24-1,VplTp=vp2,VpcTp=1 TransportNetwork=1,AtmPort=MS-24-1,VplTp=vp2 lpr !loadmodule|program ==> all MOs except those matching "loadmodule" or "program" will be printed. lpr 20.*os

Equipment=1,Subrack=1,Slot=20,PlugInUnit=1,Etm4=1,Os155PhysPathTerm=1 Equipment=1,Subrack=1,Slot=20,PlugInUnit=1,Etm4=1,Os155PhysPathTerm=2 pr cc[1-4] TransportNetwork=1,AtmCrossConnection=AtmCC1 TransportNetwork=1,AtmCrossConnection=AtmCC2 TransportNetwork=1,AtmCrossConnection=AtmCC3 TransportNetwork=1,AtmCrossConnection=AtmCC4 pr cc[135] TransportNetwork=1,AtmCrossConnection=AtmCC1 TransportNetwork=1,AtmCrossConnection=AtmCC3 TransportNetwork=1,AtmCrossConnection=AtmCC5 lpr =6.*prog.*=1 Equipment=1,Subrack=1,Slot=6,PlugInUnit=1,Program=15 Equipment=1,Subrack=1,Slot=6,PlugInUnit=1,Program=1 Equipment=1,Subrack=1,Slot=6,PlugInUnit=1,Program=14 Equipment=1,Subrack=1,Slot=6,PlugInUnit=1,Program=13 Equipment=1,Subrack=1,Slot=6,PlugInUnit=1,Program=12 Equipment=1,Subrack=1,Slot=6,PlugInUnit=1,Program=11 Equipment=1,Subrack=1,Slot=6,PlugInUnit=1,Program=10 Equipment=1,Subrack=1,Slot=6,PlugInUnit=1,Program=19 Equipment=1,Subrack=1,Slot=6,PlugInUnit=1,Program=18 Equipment=1,Subrack=1,Slot=6,PlugInUnit=1,Program=17 Equipment=1,Subrack=1,Slot=6,PlugInUnit=1,Program=16 lpr =6.*prog.*=1$ Equipment=1,Subrack=1,Slot=6,PlugInUnit=1,Program=1 lpr ms-24-1 TransportNetwork=1,AtmPort=MS-24-1 TransportNetwork=1,AtmPort=MS-24-1,VplTp=vp1 TransportNetwork=1,AtmPort=MS-24-1,VplTp=vp1,VpcTp=1 TransportNetwork=1,AtmPort=MS-24-1,VplTp=vp1,VpcTp=1,VclTp=vc32 TransportNetwork=1,AtmPort=MS-24-1,VplTp=vp1,VpcTp=1,VclTp=vc33 TransportNetwork=1,AtmPort=MS-24-1,VplTp=vp1,VpcTp=1,VclTp=vc337 TransportNetwork=1,AtmPort=MS-24-1,VplTp=vp1,VpcTp=1,VclTp=vc332 TransportNetwork=1,AtmPort=MS-24-1,VplTp=vp2 TransportNetwork=1,AtmPort=MS-24-1,VplTp=vp2,VpcTp=1 TransportNetwork=1,AtmPort=MS-24-1,VplTp=vp2,VpcTp=1,VclTp=vc34 TransportNetwork=1,AtmPort=MS-24-1,VplTp=vp2,VpcTp=1,VclTp=vc35 TransportNetwork=1,AtmPort=MS-24-1,VplTp=vp2,VpcTp=1,VclTp=vc40 TransportNetwork=1,AtmPort=MS-24-1,VplTp=vp2,VpcTp=1,VclTp=vc64 lpr ms-24-1.*=vc[^3] TransportNetwork=1,AtmPort=MS-24-1,VplTp=vp2,VpcTp=1,VclTp=vc40 TransportNetwork=1,AtmPort=MS-24-1,VplTp=vp2,VpcTp=1,VclTp=vc64 ################################################## 3.3- How to specify attribute values in set/cr/acc commands ################################################## a) For attributes of type Struct, use the following syntax: attr1=val1[,attr2=val2[,attr3=val3]]]... It is not necessary to specify all the struct members, only those that are required to change can be specified. Example: >> set sid sib11 sib11repperiod=128 >> set mtp3bspitu sppriority prioslt=2 >> set mtp3bspitu sppriority prioslt=2,prioco=2 b) For attributes of type MoRef, just type the MO LDN (without "ManagedElement=1").

Eg: >> lset AtmPort=1221,VplTp=vp1 atmTrafficDescriptor transportnetwork=1,atmtrafficdescriptor=C1P4500 It is also possible to skip the first parent (eg transportnetwork, swmanagement, etc). Eg: >> cr rncfunction=1,utrancell=30451,utranrelation=30451to30521 Attribute 1 of 1, utrancellref (moRef:UtranCell): utrancell=30521 #in this case we don't have to specify rncfunction=1 c) For attributes of type array of MoRefs, separate each element of the array with spaces. Eg: >> set jvm admclasspath loadmodule=oms loadmodule=vbjorb loadmodule=asms_sharp loadmodule=iaik loadmodule=cma loadmodule=roam >> acc aal2pathdistributionunit=1 addPath Parameter 1 of 1, aal2PathVccTpId (sequence-moRef-Aal2PathVccTp): aal2pathvcctp=csa aal2pathvcctp=csb d) For attributes of type array of Struct, separate each element of the array with semicolons. Eg: >> set rncfunction aliasPlmnIdentities mcc=300,mnc=23,mnclength=2;mcc=345,mnc=32,mnclength=2;mcc=208,mnc=123,mnclength=3 e) For attributes of type array of anything besides MoRef (eg: integer, string, boolean, etc.), separate each element of the array with commas. Eg: >> set antfeedercable=6 ulattenuation 10,10,10,10,10,10,10,10,10 >> set jvm options -Xms65000k,-Dhttp.root=/c/public_html,-Dse.ericsson.security.PropertyFileLocation=/c/java/SecurityManagement.prp >> set cell=3041 ActiveOverlaidCDMAChannelList true,true,false,true >> acc managedelementdata addDhcpServerAddress Parameter 1 of 1, ipAddressArray (sequence-string): 10.1.1.3,10.1.1.4 f) To input an empty value: * in set command, just leave the value field blank. Eg: >> set 0 userlabel (# attribute type is string) >> set reliableprogramuniter admpassiveslot (#attribute type is MoRef) * in cr command, type "null" if it's an MoRef or "d" for other attributes. This only works for non-mandatory (restricted) attributes, because mandatory attributes must have a value ################################################## 3.4- Moshell command line ################################################## The command line uses the Readline library from bash. Here are some of the supported function keys: - right arrow or Ctrl-f : move forward one character - left arrow or Ctrl-b : move backward one character - up arrow : previous command in history buffer - down arrow : next command in history buffer - backspace : delete one character backward - Ctrl-d or <del> : delete one character forward - Ctrl-a or <home> : go to beginning of line - Ctrl-e or <end> : go to end of line - Ctrl-u : erase all characters backward - Ctrl-k : erase all characters forward - Alt-f : move forward one word

- Alt-b : move backward one word - select or select + ctrl-<insert> : copy to clipboard - <insert> or shift-<insert> : paste from clipboard Note about command history: if you type the beginning of a command and then use the up/down arrow key, you will see all previous commands starting with this string ################################################## 3.5- Piping ################################################## Some commands support piping, eg: OSE shell commands, lh, tg, str, etc. This is usually indicated in the menu and the help for that command. Examples: >> te log read | grep ERROR >> lh mp te log read | grep ERROR >> str | grep cell=30456 For other commands that don't support piping (like MO commands), the workaround is to save the output to a logfile then run the unix command on that logfile by using the "l" or "!" command. Example: >> l+ #open the logfile, an arbitrary name will be given >> prod loadmodule #run the command >> l- #close the logfile >> l sort $logfile #run the unix command on the logfile. $logfile is a default variable that stores the name of the latest log created >> l grep -i basic $logfile RETURN ####################################################################################

Lazy ####################################################################################*************************************** 5.1- SW upgrade: *************************************** Create the upgradepackage MO >> cr swmanagement=1,upgradepackage=<upgradepackage> >> at the prompt, enter ftpserveraddress and upcontrolfilepath >> at the next prompts, enter ftp server userid and password, or just "d" for default value (will be anonymous) Check the proxy of the newly created MO and call action install >> acc <proxy> install Or: use the "nonblockinginstall" action in order to monitor the progress during installation: >> acc <proxy> nonblockinginstall >> get <proxy> progress Check state of upgrade package after install >> get <proxy> state Start upgrade if state is "installed" >> acc <proxy> upgrade Wait for upgrade to finish, then check that the UP is in state awaitingconfirm, then confirm >> get <proxy> state >> acc <proxy> confirmupgrade Check that the new cv is using the new upgrade package >> cvls *************************************** 5.2- RNC Iub operations: *************************************** >> str view state of all Iub/Cells/Channels/Nbap/Nodesynch in a table format (type "h str" for more info)

>> lbl/ldeb iub.*<iubname> block/deblock all iub children (nbaps,nodesynchs) (the .* acts as a wildcard) >> bl/deb cell=<cellname> block/deblock a cell >> str -i <iubname> view state for that site only *************************************** 5.3- Generic Node Healthcheck: *************************************** Just run the command: >> hc Type "h hc" for more info about this command For transmission issues, an end-to-end loopback test can be done on the VclTp's. This is very time consuming, so if there are many VclTp's, it is better to only run the loopback test on a few selected VclTp's that might be causing problems. >> lt vcltp|vpltp >> acc vpltp eteloopback >> acc vcltp eteloopback Another method can look for vcltp which are transmitting cells but not receiving: >> hpget vcltp . ^0$ ^[^0] or: >> ma faultyvcltp pmrec ^0$ >> mr faultyvcltp pmtrans ^[^0] However, this method will not show vcltps that became faulty after the initialisation of the counter (which usually occurs after restart) *************************************** 5.4- RNC Iub integration problems: *************************************** When trying to integrate a new RBS, some data mismatch might cause the iub, cell, or channels not to come up. Things to check are: transmission, aal2 addresses, vci values, localcellid values: Take a print of all MOs related to the Iub and check that the vci values match on both sides, check if any related MOs are down: >> lk iublink=<iub> (in RNC) >> lk iub=<iub> (in RBS) Find out the Aal2Ap used by that Iublink in RNC: >> lk iublink=<iub> or lki Check that the aal2 addresses match on all sides: >> get aal2routingcase=<rbsroutingcase> (in RNC and RXI if applicable) >> get aal2sp=1 (in RBS and RXI if applicable) Check that the aal2 path id's match on both sides: >> get aal2path.*<pathname> pathid (in RNC, RBS, and RXI if applicable) Check that the aal2 continuitycheck match on both sides: >> get aal2path.*<pathname> continu (in RNC, RBS, and RXI if applicable) Check that localcellid match on both sides: >> get cell=<cell> local (in RBS and RNC) Perform a loopback test on all VCIs of that iub, to see if transmission is ok >> lacc atmport=<port>,vpltp=<vp>,vpctp=1,vcl eteloopback Check RNC/RBS alarms >> al Check RNC devices are ok >> std Check Cell error code, cellbarred, actor info, etc. >> tgc/tgd (type "h tg" for info) Check RNC/RBS general state, look for potential HW/SW faults >> hc Check all cross-connects are ok >> stc (mainly in RXI/MGW) Find out the module MP that is handling the site and check if there are some errors: >> get iublink= module >> lh modXX te log read (to restart the module MP, you can use the command "acc modXX restart") ***************************************

5.5- RNC Iu integration issues: *************************************** Take a print of all MOs related to the Iu and check that the vci values match on both sides, check if any related MOs are down: >> lt ranap >> lk ranap=<ranap> Perform a loopback test on all VCIs of that Iu, to see if transmission is ok >> lacc atmport=<port>,vpltp=<vp>,vpctp=1,vcl Check mtp/sccp data matches in both sides: >> get mtp code >> get sccp title|address Activate/deactivate a C7 link >> acc mtp=<mtp> deactivate/activate Block/deblock an Aal2Path, check that the pathid's and a2ea addresses match on both sides >> bl/deb aal2path.*<pathname> >> get aal2path.*<pathname> pathid >> get routingcase=<mscroutingcase> RETURN ####################################################################################

Scripting ####################################################################################Moshell supports the use of variables and logical constructs. These can be used directly from the command line or within moshell command files. *************************************** 6.0- Preset Variables *************************************** The following variables are set immediately after moshell startup: $moshelldir ---> path to the moshell directory $gawk ---> path to gawk $ipaddress ---> IP address to the node that moshell is connected to $moshell_version ---> the moshell version $logdir ---> path to the moshell_logfiles/logs_moshell directory $tempdir ---> path to the directory containing all temporary files for this moshell session. Gets deleted at the end of the session. The following variables are set after the MOM has been parsed: $momversion ---> the MOM version of the node (eg: RNC_NODE_MODEL_E_5_3, MGW_NODE_MODEL_R3_9_0) $celloversion ---> the Cello MOM version (eg: 3.3, 4.3, 5.1, etc) of the node $momdocnumber and $momdocrevision --> the document number and revision of the MOM (eg: 15554-AXD10503/1 , rev: Z1) These variables can be handy to have when a script needs to know what SW revision is running in the node or what kind of node it is. The following variables are set after running certain MO commands: $nr_of_mos --> the number of MOs that were printed on screen by the last run of the pr/st/get/prod/fro/set/del/acc commands. $nr_of_mos_ok --> the number of MOs that were successfully operated upon by the last run of the set/del/acc commands. $command_result --> set after the cr/pcr/pset/trun commands. Possible values: 0 for success, 1 for failure. $nr_of_alarms --> the number of active alarms on the node. Set after the last run of the "al" command. $nr_of_cvs --> the number of CV:s that exist on the node, is set after the last run of the "cvls" command. $nr_of_scanners --> the number of scanners printed by the last run of the pst/pgets/pdel/pbl/pdeb commands. $nr_of_counter_instances --> the number of counter instances printed by the last run of the pgetsn command.

$moncommand --> the command to start the monitor client after having run the "mon" command. The following variables are set after running one of the l+/u+/u- commands. $logfile ---> the logfile that is currently open. Set immediately after executing the "l+" command, stays set even after "l-" and will only be reset the next time a new logfile is open with "l+" $undologfile ---> the logfile used by the undo command. Set immediately after executing the "u+/u+s" command, stays set even after "u-" and will only be reset the next time a new undo mode is started with "u+/u+s". $undocommandfile --> the command file that can be used to undo the commands that were run between "u+/u+s" and "u-". Set immediately after executing the "u-" command. $undodelcommandfile --> the file containing the delete commands. Only applicable to simulated undo mode "u+s". The following variable is set after having logged on to the node via telnet/ssh or ftp/sftp. $password The contents of the variable can not be printed, it will only show if it's empty or not. By setting this variable to empty (by doing: $password = ), this will force moshell to check the password again. Useful in case the password has changed on the node during the moshell session. The following variable is set after running the "pv" command. $nr_of_vars This variable indicates the number of scripting variables that were printed in the last "pv" printout. By using "pv" together with a filtering pattern (eg: pv $table), it is possible to find out the number of variables that had matched the pattern, for instance the number of elements in a hashtable. The following variable is set after using the functions "readfile" or "testfile". $nr_of_lines After using the function "testfile", this variable is set to 0 if the file does not exist and to 1 if the file exists. After using the function "readfile", this variable is set to 0 if the file does not exist and to the number of liens in the file if the file exists. The difference between testfile and readfile is that testfile won't actually read the file, it will just check if the file exists whereas readfile will test the file, then read it. Example1: $lineContent = testfile(/path/to/myfile) if $nr_of_lines = 0 l echo "File not found!" return fi Example2: $lineContent = readfile(/path/to/myfile) if $nr_of_lines = 0 l echo "File ot found!" return fi for $lineNumber = 1 to $nr_of_lines if $lineContent[$lineNumber] ~ thispattern print We found it! The line is $lineNumber. return fi done Example: list all scripting variables currently set >> pv $logdir = /home/eanzmagn/moshell_logfiles/logs_moshell $momversion = RNC_NODE_MODEL_E_5_3 $moshelldir = /home/eanzmagn/tools/moshell $celloversion = 4.3.1

$gawk = /home/eanzmagn/tools/moshell/gawk $ipdaddress = 10.1.128.17 $moshell_version = 6.1 $nr_of_mos = 1 $password = ******* *************************************** 6.1- Variable assignment *************************************** A variable value can be assigned in six ways, see below. A variable can also be unassigned, using the "unset" command. By using the command "unset small", all variables are unset, except: - the "system" variables ($gawk, $ipaddress, $password, $moshell_version, $moshelldir, $logdir, $momversion, $celloversion) - the "global" variable(s) (ie: assigned with the ":=" sign, instead of "="). By using the command "unset all", all variables are unset except the "system" variables. NOTE !!! It is always good practice to unset a variable as soon as it is not needed anymore since having too many variables defined slows down the processing of the command line. It is also good to do "unset all" at the beginning and end of a command file (and before doing the "return" command) in order to avoid interference from un-needed variables. See the script examples in moshell/commonjars/scripts. To print all currently assigned variables, use the command "pv" (used to be called "printvars"). To just print one variable, type: >> pv <pattern> (where the pattern matches the variable(s) to print) Or: >> print $variable a) from the command line The variable to be assigned is on the left side of the equal sign and the value is on the right side. Each element must be separated by spaces. Example: >> $i = 3 >> $node = RNC >> $password = (set the password to an empty value, will force moshell to check the password again). b) at moshell startup, using the "-v" option In this case, the "$" sign should be omitted (otherwise it gets interpreted by the unix shell) Example: >> moshell -v upmo=CXP9011008_R1A03,ftpserv=10.1.0.16,secure_shell=1,secure_ftp=1 rnc34 In this case, we can see that scripting variables ($upmo and $ftpserv) and user variables (secure_shell and secure_ftp) have been mixed in the same statement. This is ok because any variable that is not recognised as a user variable will be treated as a scripting variable. b) from the following commands: get, fro, ip2d/d2ip, h2d/d2h, uv. The mo-filter and attribute-filter must be specified, then comes the redirection sign (">"), then the variable name. If several attributes are printed, only the last attribute value gets assigned into the variable. Examples: >> get 0 productName > $nodeType (result: $nodeType = RBS3202) >> get ethernetlink ipaddress > $ipaddress (result: $ipaddress = 10.1.128.17) >> get configurationversion currentupgrade > $currentUp (result: $currentUp = UpgradePackage=CXP9011123_R12F) >> get $currentUp administrativedata > $swRev (result: $swRev = Struct{5} >>> 1.productNumber = CXP9011123 >>> 2.productRevision = R12F etc.)

>> lfro subrack=ms,slot=1,pluginunit=1$ ^r > $froid (result: $froid = 0) >> d2ip -4127129085 > $ip_addr (result: $ip_addr = 10.1.2.3) >> h2d 0xa > $res (result: $res = 10) >> uv ^credential > $credential (result: /home/ericsson/moshell/commonjars/host.p12) c) using an arithmetic operation The following numeric operations are supported: + addition - substraction * muliplication / division % modulo (returns the remainder of an integer division operation) Examples: >> $i = 1 (result: $i=1) >> $i = $i + 1 (result: $i=2) >> $j = $i * 3 (result: $j=6) >> $k = $i * $j (result: $k=12) >> $l = $i / $j (result: $l=0.333) >> $m = $k % 5 (result: $m=2) Note: Only one operation per line is allowed. A space must exist between each element of the operation. There cannot be more than two members in the operation (ie: $i = $j + $k ==> OK. But $i = $j + $k + $l ===> NOTOK) d) using output from a unix command: The unix command must be surrounded by back-quotes (`). Variables can be used within the unix command. Example1: >> $date = `date +%y%m%d-%H%M` (result: $date = 040930-1745) >> get ethernetlink ipaddress > $ipaddress (result: $ipaddress = 10.1.128.17) >> $logfile = $ipaddress_$date.log (result: $logfile = 10.1.128.17_040930-1745.log) >> l+m $logfile (open a logfile, don't display anything on the screen) >> te log read >> l- (close logfile) >> $errors = `grep -c ERROR $logfile` (result: $errors = the number of ERRORs found in the logfile) >> l rm $logfile (remove the logfile) Example2: making a cv that has the same name as the current startable cv but the last digit is incremented by 1 >> lt configurationversion >> get configuration startable > $startable (result: $startable = RBS3045_P2.1.5_CU3_A_01) >> $cvname = `$gawk -v cvname=$startable 'BEGIN { print gensub(/..$/,"",1,cvname) sprintf("%02s",substr(cvname,length(cvname)-1)+1) }'` >> cvms $cvname (result: $cvname = RBS3045_P2.1.5_CU3_A_02) e) using string manipulation The following string operations are supported: concatenation and substitution/replacement. The concatenation is performed by juxtaposing the strings. Syntax for concatenation: $var = string1string2string3 (the strings are concatenated without space in between) or $var = string1 string2 string3 (the strings are concatenated with spaces in between) The substitution/replacement is performed using the "-s" switch to specify the string to substitute and the "-r" switch to specify the string it should be replaced with. If the "-r" switch is not used, then the string will be replaced by nothing. If the "-g" switch is specified, then all instances of the string to substituted, otherwise, only the first instance. Syntax for substitution/replacement: $var = originalString -s stringToSubstitute [-r stringToReplaceItWith [-g ] ]

Regular expressions can be used in the string manipulations. Examples: >> $var = abc_defabc ghi >> $var1 = $var -s abc (result: $var1 = _defabc ghi , only first instance of "abc" was replaced) >> $var2 = $var -s \x020 (result: $var2 = abc_defabcghi , the space sign was removed) >> $var3 = $var -s abc -g (result: $var3 = _def ghi , all instances of "abc" were replaced) >> $var4 = $var -s abc -r xyz (result: $var4 = xyz_defabc ghi , first instance of "abc" was replaced with "xyz") >> $var5 = $var -s abc -r xyz -g (result: $var5 = xyz_defxyz ghi , all instances of "abc" were replaced with "xyz") >> $var6 = $var -s a.*c -r xyz (result: $var6 = xyz ghi , the regular expression "a.*c" was replaced with "xyz") >> $var7 = $varABC$var6 (result: $var7 = abc_defabc ghiABCxyz ghi , the three strings "$var", "ABC" and "$var6" have been concatenated) >> $var8 = $var ABC $var6 (result: $var8 = abc_defabc ghi ABC xyz ghi , there are spaces in between the three strings) Note: if more advanced string manipulation is needed, it is always possible to use an external program such as gawk to do the string manipulation. See example 2 in paragraph d) above. f) using output from a predefined function Currently, the following functions exist: * fdn(proxy) ---> input is the proxy id, output is the FDN * ldn(proxy) ---> input is the proxy id, output is the LDN * rdn(proxy) ---> input is the proxy id, output is the RDN * motype(proxy) ---> input is the proxy id, output is the MO type * proxy(string) ---> input is the LDN or FDN (NOT RDN!), output is the proxy id * readinput(sring) ---> input is a prompt that should appear on the screen, so that the user can input an answer which will then be assigned to the variable. * readfile(file) ---> input is a filename. Each line of the file is assigned into an element of the hashtable into which we have assigned the result of the function. If the file is not found, the variable $nr_of_lines is set to 0, otherwise it is set to the number of lines in the file. Note, this should not be used on large files as it will slow down things very much. * testfile(file) ---> input is a filename. If the file is not found, the variable $nr_of_lines is set to 0, otherwise it is set to 1. * split(string) --> The string is split into the array specified on the left side of the equal sign (see example below). The separator used to split the string can be specified in the variable "$split_separator". By default it is a space. If the $split_separator has been changed and needs to be reset to the default value, just run the command "unset $split_separator". The number of elements in the array is stored in the variable $split_last Example1: >> lt iublink >> ma iub iub >> for $mo in iub $mordn = rdn($mo) if $mordn ~ 1023 lcc $mordn lbl $mordn, fi done Example2: >> $var = readinput(Please confirm [y/n]: ) >> if $var !~ ^y return fi

Example3: >> $table = readfile(/path/to/myfile) >> for $lineNumber = 1 to $nr_of_lines print $table[$lineNumber] $word = split($table[$lineNumber]) if $word[1] ~ ^# $nr_of_comments = $nr_of_comments + 1 fi unset $word unset $table[$lineNumber] done (Note: by unsetting the entry we've just read - provided we don't need it anymore - will make things faster) g) Example The purpose of the little moshell script below is to make a customized CV name like: date_nodeType_swRev >> cvls >> $date = `date +%y%m%d` (result: $date = 040930) >> get 0 productName > $nodeType (result: $nodeType = RBS3202) >> $nodeType = $nodeType -s RBS (result: $nodeType = 3202) >> get configurationversion currentupgrade > $currentUp (result: $currentUp = UpgradePackage=CXP901913%2_R12N) >> get $currentUp administrativedata > $swRev (result: $swRev = Struct{5} >>> 1.productNumber = CXP901913/2 >>> 2.productRevision = R12N >>> 3.productName = CXP901913%2_R12N ....) >> $swRev = `gawk -v currentsw="$swRev" 'BEGIN{ swrev=gensub(/\r|\n/,"","g",currentsw) ; print gensub(/^.*Revision = | >>> 3.product.*$/,"","g",swrev) }'` (result: $swRev = R12N) >> cvms $date_$nodeType_$swRev (result: cvms 040930_3202_R12N ) *************************************** 6.2- Hashtables (arrays) *************************************** The index and the value of the hashtable can be a variable, a constant, or a mix of both. All variable assignment methods described in chapter 6.1 apply for assigning values into hashtables as well. To print a hashtable, do: pv <table> Examples: Assigning constants into a hashtable >> $table[1] = hello >> $table[2] = hej >> $table[hoho] = 5 >> pv tab (result printout:) $table[hoho] = 5 $table[1] = hello $table[2] = hej Assigning variables into a hashtable >> $mo = AtmPort=MS-6-1 >> $proxy = proxy($mo) >> $proxylist[$mo] = $proxy >> $mo = AtmPort=MS-6-2 >> $proxy = proxy($mo) >> $proxylist[$mo] = $proxy >> pv proxylist (result printout:) $proxylist[AtmPort=MS-6-1] = 103 $proxylist[AtmPort=MS-6-2] = 112 More examples on how to use hashtables are described in 6.4.

*************************************** 6.3- If/Else constructs *************************************** The if statement must be followed by a condition. The comparison operator of the condition must be surrounded by spaces. Zero or more "else if" statements can be used after the "if" statement. Zero or one "else" statements can be after the "if" or "else if" statements. The end of the if/else structure must be specified with a "fi" statement. Each statement must be on its own line and can be followed by one or more commands. Several conditions can be combined, using the logical AND (&&), or the logical OR (||). Any number of AND/OR can be put on a line but NOT BOTH on the same line. Grouping conditions with brackets is NOT supported. The "return" command can be used to exit from the command file in case a certain condition is met. Type "h return" for more information on how to use this command. Syntax examples: a) if <condition> command1 command2 fi b) if <condition1> || <condition2> command1 command2 else command3 fi c) if <condition> && <condition2> && <condition3> command1 else if <condition4> command2 else command3 fi A condition can use the following comparison operators: = equals ~ matches != is not equal to !~ does not match > greater than < less than >= greater or equal than <= less or equal than The words around the operator can be either a variable or a single word but NOT a string containing spaces or a concatenation of a variable and string. Following conditions are syntaxically correct: if $var1 = $var2 if mystring ~ $var if 10 > 3 if $i < 2 Following conditions are NOT syntaxically correct and will return unexpected results: if mystring_$var1 ~ $var2 if mystring is this ~ your string A condition can also just contain one variable, in which case it will check if the variables exists. Examples: >> if $var ---> check if the variable $var exists >> get 0 productname > $nodeType >> if $nodeType ~ 3202 || $nodeType ~ 3104 get feeder attenuation set feeder attenuation 4

else if $nodeType ~ 3101 get feeder attenuation set feeder attenuation 16 else get feeder attenuation fi *************************************** 6.4- For constructs *************************************** The parameter to the "For" construct can be: a) "ever" : to repeat the loop an infinite number of times b) <numberOfIterations> : to repeat the loop a specific number of times c) $mo in <moGroup> : to run the body of the loop on each MO of the specified moGroup. MO groups are created with the "ma" command, type "h ma" for info. d) $board in <boardGoup> : to run the body of the loop on each board of the specified board group. Board groups are created with the "ba" command, type "h ba" for info. f) $var in $table : for each iteration of the loop, $var will cycle through the index values of the hashtable $table g) $var = $start to $stop : $var is assigned every integer value between $start and $stop. $start and $stop can be variables or constants but must be an integer. If $start is smaller than $stop than the order will be ascending, otherwise it will be descending. The end of the "for" structure must be specified with a "done" statement. The "wait" command can be used in the body of the loop to specify a delay to wait in between each iteration. The delay can be in seconds, minutes, hours, or even ROP periods. (Type "h wait" for info.) Do not use the "sleep" command as this will result in hanging if the loop is aborted. The loop can be aborted any time by typing ctrl-z , then "touch <stopfile>", then "fg". The <stopfile> path is shown in the window title bar. Type "h ctrl-z" for more info about aborting. The break command can be used within the loop to exit from the loop. Syntax examples: a) for ever command1 command2 done b) for <numberOfTimes> command1 wait <numberOfSeconds> done c) for $mo in <moGroup> get $mo <attribute> > $variable $variable1 = .... set $mo <attribute> $variable1 etc... done d) for $board in <boardGroup> bl $board facc $board restart 0 1 wait 10 deb $board lhsh $board vii done e) for $proxy in $proxytable bl $proxy st $proxy deb $proxy st $proxy get $proxy operational > $opstate if $opstate != 1

break fi done f) for $var = $maxproxy to $minproxy del $var done for $var = 1 to 6 te e trace$min process done Examples: a) checking the progress of a UP installation, every 10 seconds. Break from the loop if the result is "1 (INSTALL_COMPLETED)", and continue with upgrade action. Abort the command file if the result is "6 (INSTALL_NOT_COMPLETED)" >> lt upgrade >> acc upgradepackage=xxx nonblockinginstall >> for ever $return = 0 wait 10 get upgradepackage=xxx state > $upstate if $upstate ~ ^1 break else if $upstate ~ ^6 $return = 1 break fi done if $return = 1 return fi acc upgradepackage=xxx upgrade b) run a testcase 50 times >> for 50 run testcase_3.1.1.cmd wait 2m done c) increase the primaryCpichPower by 0.1 dBm on each UtranCell >> lt ^utrancell >> ma cell ^utrancell >> for $mo in cell get $mo primarycpichpower $pich $pich = $pich + 1 set $mo primarycpichpower $pich done d) restart all boards in a board group >> ba spb spb >> for $board in spb acc $board restart 0 1 done e) save the fro values of all programs into a table and then restart every program >> lma programs_on_slot_19 subrack=ms,slot=19,.*program >> for $prog in programs_on_slot_19 $i = $i + 1 fro $prog ^res > $frolist[$i] done >> for $fro in $frolist

restartObj pgm $fro done f) restart some boards in a specific order >> for $var = 20 to 14 $board = 00$var00 facc $board restart 0 1 done *************************************** 6.5- User-defined functions *************************************** Users can define their own functions, using the func/endfunc construct. If the function is called with arguments, these are assigned to the variables $1, $2, $3, etc Example: 1. Define the function (the function definitions can be run in a different command file) Here we are defining a function which checks the state of the mirrored disks and returns once the disks are in sync func check_disk_state #if $1 is undefined or different to an integer value then we set it to 10 seconds if $1 ~ ^[0-9]+$ $wait_interval = $1 else $wait_interval = 10 fi for ever wait $wait_interval l+om $tempdir/diskstate lh coremp mirror s l- $res = `grep -c "Peer Disk Status: *Valid" $tempdir/diskstate if $res > 0 break fi done endfunc func waitforuser $date = `date "+%Y-%m-%d %H:%M:%S"` for ever $reply = readinput(Waiting from [$date]. Type "y" when ready: ) if $reply ~ ^[yY] break fi done $date = `date "+%Y-%m-%d %H:%M:%S"` print "Finished waiting at [$date]" endfunc endfunc 2. Call the function Here we have made a small script which makes use of our user-defined function. First we are running a file containing all the definitions for our user-defined functions. (Note that the functions can also be defined within the same script, but by keeping all functions in a separate file means that several command files can use the same functions) We have called the function check_disk_state with an argument "5" which in this case will be used as the "$wait_interval" parameter in the function run ~/myfunctions_define.mos for ever check_disk_state 5

waitforuser acc 0 restart pol done *************************************** 6.6- Nesting *************************************** It is possible to nest one or more if/else statement within a loop statement and vice-versa. But it is currently not possible to nest an if/else statement within an if/else statement and a loop statement within another loop statement. The current workaround is to put the for/if constructs into functions. See chapter 6.5 for more info on functions. Example: The following script starts the install, then checks the state of the install every 10 seconds. Once the upgradepackage is installed, it starts the upgrade. Then it checks the state again and once the upgrade is in state "awaitingconfirm", it confirms the upgrade. $UP = upgradepackage=CXP9011123_R12F acc $UP nonblockinginstall for ever wait 10 get $UP state > $state if $state ~ ^1 break fi done get $UP state > $state if $state ~ ^1 acc $UP upgrade fi wait 120 for ever wait 10 get $UP state > $state if $state ~ ^3 break fi done if $state ~ ^3 acc $UP confirmupgrade fi *************************************** 6.7- Examples *************************************** Example scripts can be found under moshell/commonjars/scripts and moshell/examples/scripting/ Note two types of comments can be used in scripts: - visible comments: start with the "#" sign. These comments are printed on the screen while the script is executing. - invisible comments: start with the "//" sign. These comments are not printed on the screen. RETURN ####################################################################################

Utilities ####################################################################################

The moshell package includes a number of utilities that complement the moshell functionality. They are stored in the same directory as moshell but are executed as separate, stand-alone scripts. Detailed information about each utility can be found by executing the utility without any arguments. (Except for the PM tools where the help is shown by using the "-help" option, eg: pmExtract -help). *************************************** 7.1- Network Management Tools *************************************** The network management utilities are for performing operations on many nodes in parallel. The list of nodes on which to perform the operations shall be stored in a file called the "sitefile". The ip-addresses/DNS-names and passwords of all nodes of the network must be stored in a reference file called the "ipdatabase". The ipdatabase uses the following syntax: <nodeName> <nodeIpAddress> <nodePassword> OR: <nodeName> <nodeDNSaddress> <nodePassword> (It is recommended to use the DNS-address instead of the IP-address). An example of a sitefile and an ipdatabase can be found in moshell/examples/sitefiles and moshell/examples/ipdatabase. * mobatch : to run moshell commands or command files towards many nodes in parallel. * restartcollector : to collect restart data (manual and spontaneous restarts), system downtime, and upgrade data, from many nodes in parallel. Data is presented in a report together with statistics and TR mapping and can be imported in other tools (such as Excel). * swstat : a- to collect SW level and CV from many nodes in parallel. b- to delete UP's from many nodes in parallel. * swup : to SW upgrade many nodes in parallel. * cvms : to create CV's on many nodes in parallel. *************************************** 7.2- Parameter Auditing Tools *************************************** The auditing tools are for offline postprocessing of Node logs ("MO dumps") and reference files in order to check parameter validity or health-checks. * rncaudit : to compare rnc moshell dumps against a number of reference files (CDR, winnow baseline, Uerc data, etc.). Certain consistency checks can be performed (scrambling code collisions, cell relations consistency). Rncaudit "-b" option can be used on other nodes as well such as MGW, RXI. * rbsaudit: to compare rbs moshell dumps against a number of reference files (CDR, winnow baseline). * cmpMoDump: to compare two MO dumps. * netcheck : a- to parse moshell health-check logs and check for obsolete HW, HW faults, errors, etc. b- to compare pre-check and post-check (eg health check logs before and after an upgrade or a testcase) * mocmd : a- to convert a file from winnow baseline format to moshell command file b- to convert a change_all script to moshell command file *************************************** 7.3- PM Tools *************************************** The PM tools are for offline postprocessing of Performance Management XML files. They consist of a number of command-line tools, designed to be linked together in a pipeline (ie the output of one tool feeds into the next). Note: the utilities pmExtract/pmXtab/pmDiff are used by the pmr and pmx commands in moshell. * pmExtract : to extract counter values from the XML files. The counter values to be extracted are selected based on the managed object and counter name. The counters are output to the standard output, one line per counter value.

* pmXtab : to aggregate counters according to time, Managed Object hierarchy or arbitrary relations * pmDiff : to output the difference between counter values in successive XML files. This is useful for counters that are not automatically reset after each period (eg. Cello counters). * pmList : to list all counters defined in a XML ROP file. * pmAvgRssi : to parse RBS rssi counter values. For more information, run the utility with the "-help" option (eg "pmExtract -help") or have a look in the "pmTools" document stored on http://anon.ericsson.se/eridoc/component/eriurl?objectId=09004cff80469f5c&action=current&format=msw8 (version pA1 can also be found in moshell/examples/pm_files/pmTools.doc) *************************************** 7.4- Miscellaneous Tools *************************************** * momdoc : to convert a MOM from xml format to html format * swcomp : to compare SW between two nodes containing similar HW. * pwrdef (obsolete): to generate command files for undefining and redefining the powersupply MOs on the RBS 3101's. This utility was used at a certain level of SW where there were some issues with the power supply. It should not be needed anymore. * modit (obsolete): this utility was made for a specific problem and should not be needed anymore. Note: There are other files in the moshell directory but they are moshell components and not meant to be executed as stand-alone scripts. RETURN ####################################################################################

Server Maintenance ####################################################################################When running moshell on a server in a multi-user environment, there needs to be regular maintenance in order to clean up the disk and any hanging processes. *************************************** 8.1- Hanging Processes *************************************** A known bug of moshell is that it doesn't always shut down all of its spawned processes upon exiting which leads to CPU overload and run out of RAM memory. This problem should now be fixed thanks to the use of various timeouts but if this does not help, then it is recommended to regularly check the rogue processes using the unix command "top". Once the "top" command is running, you can type the following commands in the "top" screen: - "n" followed by the number of processes to display (e.g "n 40") --> to show more than the default number of 15 processes - "o" to change the order of the sorting. E.g: "o time" (to see the processes that have been running for the longest time) "o size" (to see the processes that are using up the most memory) "o cpu" (to see the processes that are using up the most cpu. this is the default). - "k" followed by the process to kill. E.g "k 2742" *************************************** 8.2- Disk full *************************************** * To check how full the disks are, you can use the unix command "df -k".

* To see which directories are the most full, use the "du" command. E.g: To see all directories of size greater than 100,000 KB >> du -k | awk '$1 > 100000 {print}' * To see which files are taking the most space, use the "find" command. E.g: To find all files greater than 10,000 KB in the current directory (.) and sort them by size. >> find . -type f -size +10000c -ls | sort +6n * To compress any logfiles greater than 10 MB and older than 60 days >> find . -mtime +60 -type f -size +10000c -name '*.log' | xargs gzip *************************************** 8.3- Run out of memory *************************************** If you get the following error when trying to start moshell: gawk: fatal: cannot create child process for `/tmp/readlineXXXX_hhmmss' (fork: Not enough space)". It means that you do not have enough memory (i.e. RAM + swap space) on the machine. Try running the command "top" on the Solaris box (it might not exist on the box though). If you can run it, you'll see a line like this: Memory: 512M real, 107M free, 333M swap in use, 2.0G swap free A fundamental rule of Operating System management is that your swap space should also be > 2x the memory, so in this box we have 512Mb of RAM so we should have at least 1Gb of RAM (it started with just 256Mb of RAM - and we had this problem after opening a few sessions of MoShell). As a rule - if you are running MoShell on a Solaris box you should give it at least 512Mb of RAM and ideally 2Gb of swap space. Luckily - there is an easy way to add new swap space - this is to make a new "swap file" on the disk (then you don't need to repartition everything). You can do this in Solaris by following these steps: >> mkfile -v 2000m /usr/swapfile This will make a 2Gb file "/usr/swapfile" to be used as our extra swap space. But it's not enabled as swap space yet.. To add it as swap space: >> swap -a /usr/swapfile This adds it in as swap space. But this is not permanent, next time you reboot the machine it'll disappear. You can make it permanent by adding the following line to (the end of) /etc/vfstab /usr/swapfile - - swap - no - See "man vfstab" for more details on /etc/vfstab RETURN ####################################################################################

Offline Mode ####################################################################################To create an MO dump, connect to a node and run the commands: lt all ; l+ ; get (or kget) ; l- To browse an MO dump in offline mode, start moshell with: moshell /path/to/the/modump. The following commands are supported when browsing an MO dump in offline mode. MO commands: ************ parsemom ma/lma/mr/lmr/mp pr/lpr st/lst str[12t] std stc get/lget mget/lmget inv prod del/ldel rdel/lrdel

dif lki bl/lbl deb/ldeb lk/llk cvls/cvcu lt <mo_dump> mom[ct]/pmom[c]/lmom[c]/emom run Other commands: ************** h/m/n/o (help commands) ul/b/p/w/prox/time/noload/col (toggle commands) hc hi l/! bo/bor alias/unalias lmid ip2d/d2ip for/if/func/break/return/wait/print/unset (and all other scripting constructs) uv/pv l+[mso]/l-[s]/l? u+[s]/u-/u? pmr[ag] pmx[hfdn] pme[d][cgu] ******************************************************* lh <boardGroup> {<OSE-command>|run <commandfile>} [ | <unix commands>] ******************************************************* See help for bo/ba/baw/br/brw/bp commands, for more info. E.g: type "h bo". RETURN ******************************************************* bo[r]/ba[s]/baw[s]/bad/br/brw/brd/bp ******************************************************* Syntax: * bo[r] * ba[s]/br/bp <boardGroup> <boards> * baw[s]/brw <boardGroup> <swa> [<rncMod>] * bad/brd <boardGroup> <devType> [<rncMod>] This set of commands allows the user to create board groups that can be used for running OSE commands on multiple boards. The following board groups are always created by default after running any of the board commands (bo/ba/br/lh, etc) the first time: * "all": contains all boards (MP/BP) as well as SPMs (if present). * "coremp": contains the core MP(s), one or two depending on the configuration. * "mp": contains all MP boards. * "bp": contains all BP boards. In RNC, the following board groups are also created by default, containing MPs/SPMs connected to the various RNC modules: * mod[x] * cc[x] * dc[x] * pdr[x]

Description: * It is recommended to start running the "bo" command ("board overview") to view what boards are present in the node. The very first time "bo" is run on a node, it will take more time because it has to fetch data from the node. The data is then permanently stored on the workstation so that the command will be quicker the next time moshell is connected to that node. To empty the cache and force moshell to reread the node's board data, just use the "bor" command. * The ba command is used for adding boards into a group. The boards shall be identified by their position or a string matching the board type. The "s" switch adds any related SPMs to the board group. Examples: >>> ba group1 1 2 4-8 114-119 ==> boards 000100, 000200, 000400 to 000800, 011400 to 011900 are added to group1 >>> bas group1 223-226 ==> boards 022300 to 022600 are added to group1, together with their related SPs (if these boards are SPBs). >>> ba group1 spb scb 3 4 ==> all boards of type matching "spb" and "scb" are added to group1 as well as boards 000300 and 000400 >>> ba gpb gpb ==> all boards of type matching "gpb" are adding to the group called "gpb". * The baw command is similar to the ba command except that the boards are identified by their SwAllocation and/or RncModule. Examples: >>> baw moduleMPs module ==> all boards belonging to the SwAllocation maching "module" will be added in the group called "moduleMPs" >>> baw module1 .* 1 ==> all boards belonging to rncModule 1 will be added to the group called "module1" * The bad command is for adding SPM's into a board group based on their device type. This is applicable to RNC only. Examples: >>> bad dc dc ==> add all SPM's handling a dc device to the group called "dc". >>> bad dc1 dc 1 ==> add all SPM's handling a dc device on module 1 to the group called "dc1". * The br command is for removing a whole group or certain boards out of a group. Examples: >>> br group1 1 3 gpb ==> boards 000100, 000300 and all boards of type matching "gpb" are removed from group1 >>> br group2 ==> group2 is removed * The brw command is similar to the br command except that the boards are identified by their SwAllocation and/or RncModule. Examples: >>> brw group3 dc ==> all boards whose SwAllocation matches "dc" will be removed from group3 * The bp command is for printing existing groups or the contents of a particular group. Examples: >>> bp ==> all existing groups are shown, eg: "group1" and "all" >>> bp all ==> the contents of the group "all" is shown. Once the group is created, the "lh" command is used to run an OSE command on all boards of the group. "lh all" or just "all" can be used to run a command on all boards of the node.

Examples: >>> lh group1 te log read >>> lh group1 te log read | grep ERROR: >>> lh all vii OR: all vii >>> lh all te log read | grep ERROR: OR: all err (special shortcut) It is possible to send multiple commands to each board of the board group by separating them with semicolons. Examples: >>> lh mp te log read ; llog -l ; te log clear ; llog -c >>> lh dc te e trace1 SP_HIST ; te log read It is also possible to send a command file to each board of the group. Example: >>> lh spb run sp_traces.txt When many commands are to be sent, the "lh" function will put them into a command file, transfer that file to the node and run that file from within the node, using the "shell -f" command. This will save a lot of time instead of having to send each command one by one to the node. There is a user variable called fast_lh_threshold which decides the number of commands above which a command file will be transferred to the node. See chap 0.2 and moshell file for more info about user variables. It is also possible to run MO commands on board groups. In this case, the MO command will execute against the MOs connected to these boards, ie the PlugInUnit or Spm MOs. Eg: acc mod1 restart ---> restart the MP found in board group "mod1" st mp ---> view state of all MP pluginunits acc cc1 restart ---> restart the SPMs found in board group "cc1" Note: in RNC, the "bo" command also creates a number of default MO groups "ccXdev", "dcXdev", "pdrXdev", where X is the module number. So, in order to lock/unlock some devices, use the MO group instead of the board group since the board group connects to the SPMs which don't have an administrative state. Example: bl cc1dev More info in "h syntax". RETURN ******************************************************* cvls/cvmk/cvms/cvset/cvrm/cvcu ******************************************************* Command syntax: * cvrm <cv-name>|<cv-filter> * cvms <cvname> [<operator>] [<comment>] * cvmk <cvName> [<operator>] [<comment>] * cvset <cvname> * cvls * cvcu Description: A set of commands similar to the "cv" commands in OSE but operate through MO interface instead of telnet/ssh (ie: no password). * cvls displays both the current cv information (equivalent of "cv cu") and cv list (equivalent of "cv ls"). * cvcu displays the current cv information only (equivalent of "cv cu"). UP info doesn't appear in cvcu until you have done a cvls.

* cvmk creates a cv. Operator name and comments (not longer than 40 characters) can be given as argument. The advantage of using cvmk instead of OSE command "cv mk" is that the Upgrade Package information is included in the cv attributes. * cvset: to set a cv as startable. * cvms: create a cv and make it startable (combination of cvmk and cvset) * cvrm can remove many cv's in one go using pattern matching on the cv name (remove from rollback list is attempted before deletion). Examples: Create a cv and make it startable (no userid or comments given): >> cvms Rbs1_P2.0.16 Create a cv and make it startable (userid and comments given): >> cvms Rnc1_P2.1.2_B eanzmagn cell power increased to 33dBm Remove all cv's whose name match the string "Temp": >> cvrm Temp Remove all cv's whose name don't match the string "Final": >> cvrm !Final Remove all cv's whose name don't match the string "final" or the string "RNC": >> cvrm !Final|RNC WARNING!!!: If the OSE shell command "cv mk" is used to create a cv (instead of "cvmk" or "cvms"), the cv attributes will not contain the UpgradePackage reference which means that the cv will not be deleted when the UpgradePackage is removed. If there are CV's lying on the node without their corresponding UpgradePackage and the node is restarted on one of these cv's, there is a high risk that the node will go cyclic. To avoid this situation it is recommended to always use the moshell command "cvmk" or "cvms" when creating cv's since the UpgradePackage reference will then automatically be included in the cv attributes. More Examples: GRY027> cvset Backup080307 070517-19:47:26 10.230.17.177 7.0 RESTRICTED RBS_NODE_MODEL_H_6_6 stopfile=/tmp/22360 070517-19:47:26 10.230.17.177 7.0 RESTRICTED RBS_NODE_MODEL_H_6_6 stopfile=/tmp/22360 GRY027> confb+ GRY027> acc 23 setstartable 070517-19:47:26 10.230.17.177 7.0 RESTRICTED RBS_NODE_MODEL_H_6_6 stopfile=/tmp/22360 ====================================================================================Proxy MO Action Nr of Params ====================================================================================23 ConfigurationVersion=1 setStartable 1 Parameter 1 of 1, configurationVersionName (string): Backup080307 >>> Return value = null ====================================================================================Total: 1 MOs attempted, 1 MOs actioned GRY027> confb- GRY027> cvls ====================================================================================070517-19:47 CV Name Upgrade Package ====================================================================================Startable: Backup080307 CXP9010809/1_R30G/B Loaded: Au_CXP9010809%1_R30G%B_070517_0100 CXP9010809/1_R30G/B Executing: Au_CXP9010809%1_R30G%B_070517_0100 CXP9010809/1_R30G/B Last created: Au_CXP9010809%1_R30G%B_070517_0100 CXP9010809/1_R30G/B ------------------------------------------------------------------------------------Current UpgradePkg: UpgradePackage=CXP9010809/1_R30G/B CXP9010809/1_R30G/B CommandLog: Enabled AutoCreatedCV: Enabled

Comment [S4]: Use this CV in Next reload

Comment [S5]: Previously loaded CV

Comment [S6]: Loaded CV

Rollback status: Rollback is on Rollback init timer: 30 Rollback init counter: 5 Rollback list: s[5] = Au_CXP9010809%1_R30G%B_070516_0100 O&M_RIYADH Fi_CXP9010809%1_R30G%B_070122_2214 Rb_CXP9010809%1_R30G%B_070122_2155 Si_CXP9010809%1_R30G_070117_1329 ====================================================================================CV Name Creation Date Package Operator Comment ====================================================================================Fi_CXP9010809%1_R28D_700101_0029 1970-01-01 00:29 CXP9010809/1_R28D Cello Packet Final CV auto after_integration_working 1970-01-01 21:44 CXP9010809/1_R28D unknown none INITIAL_CV 2006-05-11 21:35 no value unknown none O&M_BACKUP_21.11.06 2006-11-21 12:09 CXP9010809/1_R28D ewisyam none Si_CXP9010809%1_R30G_070117_1329 2007-01-17 13:29 CXP9010809/1_R28D Cello Packet Install_tmp CV autocreated by SU Rb_CXP9010809%1_R30G%B_070122_2155 2007-01-22 21:55 CXP9010809/1_R28D Cello Packet Rollb. CV auto SU_CXP9010809%1_R30G%B_070122_2207 2007-01-22 22:07 CXP9010809/1_R30G/B Cello Packet Temp. CV auto Fi_CXP9010809%1_R30G%B_070122_2214 2007-01-22 22:14 CXP9010809/1_R30G/B Cello Packet Final CV auto Backup080307 2007-03-08 08:24 CXP9010809/1_R30G/B unknown none Au_CXP9010809%1_R30G%B_070509_0100 2007-05-09 01:00 CXP9010809/1_R30G/B Cello Packet Daily autocreated CV. O&M_RIYADH 2007-05-09 14:31 CXP9010809/1_R30G/B Administrator 09052007 Au_CXP9010809%1_R30G%B_070516_0100 2007-05-16 01:00 CXP9010809/1_R30G/B Cello Packet Daily autocreated CV. Au_CXP9010809%1_R30G%B_070517_0100 2007-05-17 01:00 CXP9010809/1_R30G/B Cello Packet Daily autocreated CV. ====================================================================================>>> Total: 13 CV's GRY027> reload {not recommended, do acc 0 restart instead} 070517-19:47:46 10.230.17.177 7.0 RESTRICTED RBS_NODE_MODEL_H_6_6 stopfile=/tmp/22360 $ reload /home/zm814584/moshell/./commonjars/connect: connection timed out ####################################################################################!!! WARNING: For live sites, please use the command "acc <lnh> restart" instead, as it is a more controlled kind of restart. For instance: "acc 001400 restart" ####################################################################################Broken Pipe GRY027> cvcu Last MO: 20. Loaded 1 MOs. Total: 21 MOs. MO Class: ConfigurationVersion. Last MO: 22. Loaded 2 MOs. Total: 23 MOs. MO Class: UpgradePackage. ====================================================================================070517-19:50 CV Name Upgrade Package ====================================================================================Startable: Backup080307 CXP9010809/1_R30G/B Loaded: Backup080307 CXP9010809/1_R30G/B Executing: Backup080307 CXP9010809/1_R30G/B Last created: Au_CXP9010809%1_R30G%B_070517_0100 CXP9010809/1_R30G/B ------------------------------------------------------------------------------------Current UpgradePkg: UpgradePackage=CXP9010809/1_R30G/B CXP9010809/1_R30G/B CommandLog: Enabled AutoCreatedCV: Enabled Rollback status: Rollback is on Rollback init timer: 30 Rollback init counter: 5 Rollback list: s[5] = Au_CXP9010809%1_R30G%B_070516_0100 O&M_RIYADH Fi_CXP9010809%1_R30G%B_070122_2214 Rb_CXP9010809%1_R30G%B_070122_2155 Si_CXP9010809%1_R30G_070117_1329 ==================================================================================== GRY027> cv cu 070517-19:50:50 10.230.17.177 7.0 RESTRICTED RBS_NODE_MODEL_H_6_6 stopfile=/tmp/25528

Trying password from ipdatabase file: /home/zm814584/moshell/./sitefiles/ipdatabase... $ cv cu Startable: Backup080307 Loaded: Backup080307 Executing: Backup080307 Last created: Au_CXP9010809%1_R30G%B_070517_0100 Rollback status: Rollback is on Rollback init timer: 30 Rollback init counter: 5 Rollback 1: Au_CXP9010809%1_R30G%B_070516_0100 Rollback 2: O&M_RIYADH Rollback 3: Fi_CXP9010809%1_R30G%B_070122_2214 Rollback 4: Rb_CXP9010809%1_R30G%B_070122_2155 Rollback 5: Si_CXP9010809%1_R30G_070117_1329 Rollback counter: 4 GRY027> cv rbrm O&M_RIYADH {remove from rollback list} 070517-19:52:48 10.230.17.177 7.0 RESTRICTED RBS_NODE_MODEL_H_6_6 stopfile=/tmp/25528 $ cv rbrm O&M_RIYADH ok $ GRY027> cv rbset 070517-19:55:11 10.230.17.177 7.0 RESTRICTED RBS_NODE_MODEL_H_6_6 stopfile=/tmp/25528 $ cv rbset cv [mk|rm|set|ls|cu|rbinit|rbset|rbrm|rbcnt|up|synch|upls|uprm|csum|prec|help] $ GRY027> cv help 070517-19:55:23 10.230.17.177 7.0 RESTRICTED RBS_NODE_MODEL_H_6_6 stopfile=/tmp/25528 $ cv help Create CV: cv mk <name> [id] [type] [puid] [operator] [comment] [activityLogFilePath] Remove CV: cv rm <name> Set as startable: cv set <name> List cv:s: cv ls Current usage: cv cu Set rollback init values: cv rbinit <status> <timer> <counter> - status : 0=no_change, 1=rollback_on, 2=rollback_off - timer : 0=no_change, 1-n minutes - counter : 0=no_change, 1-n Set first in rollback list: cv rbset <name> Remove from rollback list: cv rbrm <name> Set rollback counter: cv rbcnt <counter> Check if loaded cv is upgrade: cv up Clean up cv dir: cv clean <level> - level : 1=remove all cvs except one used by cv pointer. - level : 2=remove all cvs except one used by cv pointer & rollback list. - level : 3=remove all cvs on passive side that does not exist on active side. Synch from active to MP with given lnh name: cv synch <lnh> List upgrade cv: cv upls <upgrade package id> Remove upgrade cv: cv uprm <upgrade package id> Checksum cv: cv csum <name> <mode> - name: CV name to checksum files for - mode: active=active Core MP, passive=passive Core MP Precheck cv: cv prec <number of new CVs> GRY027> cv rbset Backup080307 070517-19:57:20 10.230.17.177 7.0 RESTRICTED RBS_NODE_MODEL_H_6_6 stopfile=/tmp/25528

$ cv rbset Backup080307 ok $ GRY027> cv ls 070517-20:02:44 10.230.17.177 7.0 RESTRICTED RBS_NODE_MODEL_H_6_6 stopfile=/tmp/25962 $ cv ls Please wait for list.... Name: Au_CXP9010809%1_R30G%B_070517_0100 Date: Thu May 17 01:00:12 2007 Id: 1 Type: autocreate Package upgrade: CXP9010809/1_R30G/B Operator: Cello Packet Platform Comment: Daily autocreated CV. Status: ok Name: Backup080307 Date: Thu Mar 8 08:24:06 2007 Id: Backup080307 Type: other Package upgrade: CXP9010809/1_R30G/B Operator: unknown Comment: none Status: ok Name: INITIAL_CV Date: Thu May 11 21:35:09 2006 Id: no value (cv product id) Type: other Package upgrade: no value (upgrade package id) Operator: no value (operators name) Comment: no value (operators comments) Status: ok Name: Rb_CXP9010809%1_R30G%B_070122_2155 Date: Mon Jan 22 21:55:12 2007 Id: no value (cv product id) Type: other Package upgrade: CXP9010809/1_R28D Operator: Cello Packet Platform Comment: Rollb. CV autocreated at System Upgrade. Status: ok Name: O&M_BACKUP_21.11.06 Date: Tue Nov 21 12:09:30 2006 Id: O&M_BACKUP_21.11.06 Type: other Package upgrade: CXP9010809/1_R28D Operator: ewisyam Comment: none Status: ok Name: Au_CXP9010809%1_R30G%B_070516_0100 Date: Wed May 16 01:00:12 2007 Id: 1 Type: autocreate Package upgrade: CXP9010809/1_R30G/B Operator: Cello Packet Platform Comment: Daily autocreated CV. Status: ok Name: O&M_RIYADH

Date: Wed May 9 14:31:20 2007 Id: O&M_RIYADH Type: other Package upgrade: CXP9010809/1_R30G/B Operator: Administrator Comment: 09052007 Status: ok Name: Fi_CXP9010809%1_R28D_700101_0029 Date: Thu Jan 1 00:29:27 1970 Id: no value (cv product id) Type: other Package upgrade: CXP9010809/1_R28D Operator: Cello Packet Platform Comment: Final CV autocreated at System Upgrade. Status: ok Name: after_integration_working Date: Thu Jan 1 21:44:34 1970 Id: after_integration_working Type: other Package upgrade: CXP9010809/1_R28D Operator: unknown Comment: none Status: ok Name: Si_CXP9010809%1_R30G_070117_1329 Date: Wed Jan 17 13:29:41 2007 Id: no value (cv product id) Type: other Package upgrade: CXP9010809/1_R28D Operator: Cello Packet Platform Comment: Install_tmp CV autocreated by SU Status: ok Name: SU_CXP9010809%1_R30G%B_070122_2207 Date: Mon Jan 22 22:07:56 2007 Id: no value (cv product id) Type: upgrade_tol_err Package upgrade: CXP9010809/1_R30G/B Operator: Cello Packet Platform Comment: Temp. CV autocreated at System Upgrade. Status: ok Name: Fi_CXP9010809%1_R30G%B_070122_2214 Date: Mon Jan 22 22:14:29 2007 Id: no value (cv product id) Type: other Package upgrade: CXP9010809/1_R30G/B Operator: Cello Packet Platform Comment: Final CV autocreated at System Upgrade. Status: ok Name: Au_CXP9010809%1_R30G%B_070509_0100 Date: Wed May 9 01:00:13 2007 Id: 1 Type: autocreate Package upgrade: CXP9010809/1_R30G/B Operator: Cello Packet Platform Comment: Daily autocreated CV. RETURN *******************************************************

get/lget [<moGroup>|<moFilter>|<proxy(s)>|all] [<attribute-filter>|all] [<value-filter>] ******************************************************* This command fetches one of several attributes from one or several MO's. Doesn't fetch pm attributes; to view pm attributes, use pget/lpget. Examples: get all attributes from all MOs except those whose RDN matches "utranrel" or "iub" >> get !(utranrel|iub) get all attributes from MOs whose proxies range from 10 to 30 >> get 10-30 from all MOs, get productdata containing the string 0843 (can be useful to find out which MO's are related to a certain loadmodule) >> get all product 0843 from all Utrancells, get sintersearch attribute different from 10 >> get utrancel sinter !10 get traffic descriptors for all vcltp's >> get vc trafficdes get vcltp's used by all cross-connections >> get cross vc get piutype for all MO's under "Equipment" >> lget equip piutype get attenuation values for all cables (in RBS) >> get cable atten get all attributes in nodesynch MO, belonging to site 1164 (in RNC) >> lget 1164,nodesy get all attributes in MO's under "RncFunction" matching pwr or power or sir >> lget rncfunction p.*w.*r|sir view which cells are connected to which iub's (in RNC) >> get cell iub get all attributes from nodebfunction MO, except those matching "overload" >> get nodebfunc !overload Note: a) when doing a "get <mo(s)>" or "get <mo(s)> all", one corba request is sent for each MO, asking for all attributes of that MO. b) when doing a "get <mo(s)> <attribute(s)>", a corba request is sent for up to 100 MOs at a time, asking for the specified attributes of those MOs. The implications of this is that it is faster but: a) if one or more attributes cannot be read due to some exception (eg: FRO not accessible), then all attributes will return the same exception, even if they can be read. b) if one or more MOs contain one or more attributes that cannot be read, then all MOs within that corba request will return the same exception even if they can be read. The workaround for a) is to find out which attribute is causing the problem. The command "sget" ("slow get") can be used for this. The "sget" command reads each attribute one by one. The attribute(s) that is causing the exception will then be easy to spot. It is then possible to use the standard "get" command with with the negative filter (!) to exclude the "faulty" attribute. Example: get nodebfunction !overload --> all attributes of the nodebfunction MO except those matching "overload" will be read. pget utrancell !pmnoofrrc --> all pm attributes of the utrancell MO except those matching "pmnoofrrc" will be read. The workaround for b) is to lower the speed of reading so that only one MO instead of 100 is read per Corba request. This is done using the "speed" command. Example:

st all ---> one MO is returning an exception which means that up to 100 MOs cannot be read Instead do: >> speed 1 >> st all >> speed 100 The command will be slower but the exception will only affect the MO(s) that have it and not the "healthy" ones. The speed command affects get,pget,kget,prod, and st commands. By default, "speed" is set to 100, which means that up to 100 MOs share the same corba request. By running the command "speed 1", the exception will not affect the other MOs. However the speed will be slower. It is possible to use a value from 1 to 200 to define the speed. It is recommended to not use a speed higher than 100 since this takes more memory from the node. Type "speed" on its own to see the current speed. Scripting: It is possible to store the output into a variable Example: Store one value into a variable >> get utrancell pich > $pich Store many values into an array >> for $mo in utrancellgroup $mordn = rdn($mo) get $mo pich > $pichTable[$mordn] done Refer to the Scripting Chapter for more information. RETURN ******************************************************* tg[r][c][d] ******************************************************* Print LmCell Target Observability data from all modules of the node. Command Syntax: tg[c][r] [<mofilter>|<mogroup>|<fro>][:<actorChildren>] [<rrt-cmd>] [|<unixCmds>] OR: tgd [<mofilter>|<mogroup>|<fro>][:<actorChildren>] [<cell-parameter(s)>] * Purpose: To print the relation MO<--->FRO<--->ACTOR<--->CCDEVICE for IubLink and UtranCell MOs. To send RRT commands to Cell/Iub actors or their children in the actor tree. * Arguments: By specifying the first argument, it is possible to filter the Cell/Iubs matching a specific FroId or MOid. By specifying a second argument consisting of an RRT command or a list of cell parameters, it is possible to run an RRT-command or display certain cell parameters on all the actors that are matched by the first argument. The list of available RRT commands can be seen by typing: lhsh 001400 ? rrt The list of available cell parameters can be seen by typing: - lhsh 001400 rrt-CXC132xxxx_Ryyyy 1/1/1/1/2/1.1 info (for cell parameters) - lhsh 001400 rrt-CXC132xxxx_Ryyyy 1/1/1/1/7/1.1/4/1 info (for nbapcommon parameters) etc... The printout can be piped into unix commands, like "grep" and "sort". * Options: The "r" option is to refresh the MO/FRO/ACTOR data. Otherwise this data is reused within the moshell session and from session to session, using a cache on the workstation disk. A tg refresh ("tgr") needs to be done after a node upgrade or if some IubLinks/UtranCells have been added/removed/remoduled. Otherwise you may get error messages such as "unknown command rrt-CXC1328831_Rxxx" (eg, the rrt LM has changed after an upgrade).

The "c" option prints the following extra extra fields: - Common Channel Device (ccDevice): shows which SPM is used to handle the common channels of this cell - ccDevice Module (ccMod): shows if a ccDevice is running on an SPM that doesn't belong to the same module as the cell/iub. This can be fixed by locking/unlocking the cell. It is always best to make sure that all cells are using a ccDevice located in their own module so that the load will be spread equitably on all ccDevices. Note that ccdevice data is not kept in the cache, only mo/fro/actor relation is kept in the cache. The "d" option is to print certain cell-parameters for all cells matching the first argument. Examples: >> tg ---> to view the fro/actor data for each cell/iub >> tg cell=302 ---> to view the fro/actor data for all cells starting "cell=302" >> tg cellmod1 ---> to view the fro/actor data for all MOs belonging to the MO group "cellmod1" (use "ma" command to make an MO group) >> tg 67 ---> to view the mo/actor data for the MOs that have fro=67 >> tgr ---> to refresh the fro/actor data >> tgc ---> to view all cells/iubs and their respective fro/actor and ccDevice (Note: ccDevice data is not cached so if it is not necessary to do tgr to refresh ccDevice data) >> tg iublink=3.*1$ info --> to run the rrt "info" command on all actors whose MO matches "iublink=3.*1$" >> tgc | grep 0019 --> to see all cells that are on ccdevice of board 001900 >> tg cell getattr cellData ---> to send the rrt command "getattr cellData" on all actors whose MO matches "cell" >> tg iubmod3 state --> to run the rrt command "state" on all MOs belonging to the MO group "iubmod3" (use "ma" command to make an MO group) >> tgd cell ulinterference celldata:errorstatus celldata:spconfigflag cellRoState --> to view the cell parameters "ulinterference,celldata:errorstatus,etc." on all cells. >> tgd cell cellLoadMonitor:totAseDl cellLoadMonitor:totAseUl cellLoadMonitor:currDlCode --> to view the admission tree usage on all cells (P3/P4) >> tgd cell:/8/3 cellLoadMonitor:totAseDl cellLoadMonitor:totAseUl cellLoadMonitor:currDlCode ---> to view the admission tree usage on all cells (P5 and after) >> tgd cell ulinterference celldata:spblocked celldata:spconfigflag cellRoState celldeleted cellTraceActivated celldata:errorstatus >> tgd iub:/4/1 activeStatus standbyStatus currentCause currentAvailabilityStatus rncRbsLinkLossOfRedundancy rncRbsLinkDown rncRbsDeactivated --> to view those attributes on all the NbapCommon actors Output examples: >> tgc ------------------------------------------------------------------------------------MOD MFRO ModMP UtranCellId IubLinkId CfRO IfRO CellActor IubActor CcDev ------------------------------------------------------------------------------------ 1 0 001400 90121 9012 5 1 1/1/1/1/2/1.3 1/1/1/1/7/1.1/4 0019SP2 1 0 001400 90122 9012 4 1 1/1/1/1/2/1.2 1/1/1/1/7/1.1/4 0020SP0 1 0 001400 90123 9012 3 1 1/1/1/1/2/1.1 1/1/1/1/7/1.1/4 0020SP0 >> tgd cell=9012 ulinterference celldata:spblocked celldata:spconfigflag cellRoState celldeleted cellTraceActivated celldata:errorstatus ------------------------------------------------------------------------------------MO ulinterference spblocked spconfigflag cellrostate celldeleted errorstat celltraceactivated ------------------------------------------------------------------------------------UtranCell=90121 -106 0 0 2 0 0 0

UtranCell=90122 -100 0 0 1 0 16002:CellNoDrhResources 0 UtranCell=90123 -100 0 0 1 0 16002:CellNoDrhResources 0 Description: - spblocked=1 means that the CCdevice has crashed and Rnh got the signal clearResourceReq. - spconfigflag says if the cell has allocated SP resources or not. Should be 0 if spblocked=1. - cellrostate is defined in the header file rlibRncConst.h: roStateNOK=1, roStateOK=2, roStateDepNOK=3 - celldeleted means that the cell has been deleted by the operator, i.e. FRO has sent a deleteInd. - celltraceactivated says if the feature "Selective Cell Tracing" is active or not. See CR WRNac20241 - errorstatus is different to 0 if there is a fault in the cell unlock procedure. Range 16000-16014 is specified in the file rlibEventNr.h. Cellrostate shall be equal to 1 if the errorstatus is different to 0. >> tgd iub:/4/1 activeStatus standbyStatus currentCause currentAvailabilityStatus rncRbsLinkLossOfRedundancy rncRbsLinkDown rncRbsDeactivated --> to view those attributes on all the NbapCommon actors ------------------------------------------------------------------------------------MO activestatus standbystatus currentcause currentavailabilitystatus rncrbslinkdown rncrbsdeactivated ------------------------------------------------------------------------------------IubLink=1001 1 1 2 2 0 0 IubLink=1002 1 1 2 2 0 0 ------------------------------------------------------------------------------------Description: - activeStatus and standbyStatus are boolean (0 or 1). It's the FRO's way to say if it's ok or not to attach to USAAL. UserPlaneCepId for active and standby shall be different to -1 if active/standby status equals 1. - currentCause is sent by FRO in the signals opStateChdInd and setAttribInd and is defined by the dataclass CpxUsaalEfi_OpStateChangeCauseD. Valid values are: CELLO_USAALEFI_SERVER_RESTARTED == 1 CELLO_USAALEFI_OTHER == 2 CELLO_USAALEFI_SERVER_MOVED == 3 (introduced in the feature Moveable CEP in P5MD) - currentAvailabilityStatus comes together with opStateChdInd and is about "regular" state propagation, i.e. if bit 5 is set to NBAP RO Dependency Failed. - rncRbsLinkLossOfRedundancy & rncRbsLinkDown are internal flags that say if the events linkDown and linkLossOfRedundancy are active or not. If rncRbsLinkDown=1 then currentAvailabilityStatus will be "Dependency Failed" and linkUsedForTraffic will be equal to -1. - linkUsedForTraffic says which iublink we are using at the moment. Active == 0, Standby == 1. If linkUsedForTraffic equals 1 (standby) then rncRbsLinkLossOfRedundancy is also equal to 1. - rncRbsDeactivated says if the event linkDeactivated is active or not. All 3 events are defined in header file rlibEventNr.h. >> tgd cell:/8/3 cellLoadMonitor:totAseDl cellLoadMonitor:totAseUl cellLoadMonitor:currDlCode ------------------------------------------------------------------------------------MO totasedl totaseul currdlcode ------------------------------------------------------------------------------------UtranCell=30101 320 160 3750 UtranCell=30102 0 0 3593 UtranCell=30103 0 0 3593 UtranCell=30104 1940 969 4218 UtranCell=30105 2064 1568 4375 UtranCell=30106 991 911 3984 ------------------------------------------------------------------------------------Description: - totAseDl is the total amount of DL ASE that is currently in use in the cell.

The value is scaled by a factor 100 to get a resolution of 0.01 ASE, i.e. totalAseDl = 1280 means 12.80 ASE DL load in the cell. - totAseUl is the same as totAseDl but for UL ASE. DL and UL ASE values are controlled by UEH (by signals admissionRequest, admissionDecreaseLoadInd, admissionAseUlIncreaseInd and admissionAseUlDecreaseInd). - currDlCode reflects the last reported value of DL code tree load utilization in the cell (reported from the RnhCode block by signal codeTreeLoadInd). The value is scaled by factor 100 to get a resolution of 0.01 % code tree load, i.e. codeTreeLoad = 4218 means 42.18 % of DL code tree is allocated. RETURN ******************************************************* lc[1-9]/lcc <moGroup>|<moFilter>|<proxy(s)>|all ******************************************************* The "lc" command is for loading the LDNs of the children MOs lying under an MO or group of MOs. "lc" on its own or combined with the numeric option "1" will only load the direct children. With the numeric options 2 to 9 it is possible to specify the number of levels of children to be loaded. The "c" option ("lcc" command) is for loading all possible levels of children under the MO. The parameters of the command are: - all: build a proxy table with all MO's contained in the node. - <proxy(s)>: list children of one or several MO's given their proxy id. For instance: >> lc 0 --> list the direct children of the ManagedElement MO (only one level of children) >> lc2 0 --> list two levels of children under ManagedElement MO >> lcc 0 --> list all levels of children of the ManagedElement MO (same as lc all or lt all). >> lc 4 6 7 --> list one level of children under proxys 5, 6, and 7. - <moFilter>: list children of all MO's whose RDN match the pattern. For instance: >> lc3 transportnetwork=1 ---> list three levels of children under TransportNetwork MO >> lc cell=3002 --> list direct children for MO's whose RDN match "cell=3002" >> lcc ms-24-1 --> list all levels of children under MO's whose RDN match "ms-24-1" The pattern in mo-filter is a regular expression, more information can be found with command "h syntax" and "h pr". RETURN ******************************************************* lko/llko <moGroup>|<moFilter>|<proxy(s)> ******************************************************* The old lk. Messier than lk but supports a wider range of MO classes. Output format (example): >>lko ranap=cs =============================================================================== MOs linked to 1316 RncFunction=1,Ranap=cs (-,E) =============================================================================== localSccpApRef Ranap=cs ---> (-,E) SccpSp=1,SccpScrc=1,SccpAp=1 sccpGlobalTitleRef Ranap=cs ---> (-,-) SccpSp=1,SccpScrc=1,SccpGlobalTitle=1 remoteSccpApRef Ranap=cs ---> (-,E) SccpSp=1,SccpScrc=1,SccpAp=2

reservedBy SccpSp=1,SccpScrc=1,SccpAp=1 ---> (-,-) SccpSp=1,SccpScrc=1,SccpEntitySet=1 mtp3bApId SccpSp=1,SccpScrc=1,SccpAp=2 ---> (-,E) Mtp3bSp=1,Mtp3bAp=1 reservedBy SccpSp=1,SccpScrc=1,SccpAp=2 ---> (-,-) SccpSp=1,SccpScrc=1,SccpEntitySet=2 routeSetId Mtp3bSp=1,Mtp3bAp=1 ---> (-,E) Mtp3bSp=1,Mtp3bSrs=1 reservedBy SccpSp=1,SccpScrc=1,SccpEntitySet=2 ---> (-,-) SccpSp=1,SccpScrc=1,SccpGlobalTitle=2 slsReservedBy Mtp3bSp=1,Mtp3bSrs=1 ---> (-,E) Mtp3bSp=1,Mtp3bSls=1 reservedBy Mtp3bSp=1,Mtp3bSls=1 ---> (-,E) Mtp3bSp=1,Mtp3bSrs=1,Mtp3bSr=1 nniSaalTpId Mtp3bSp=1,Mtp3bSls=1,Mtp3bSl=2 ---> (-,E) NniSaalTp=csb nniSaalProfileId NniSaalTp=csb ---> (-,-) NniSaalProfile=1 aal5TpVccTpId NniSaalTp=csb ---> (-,E) Aal5TpVccTp=csb processorId Aal5TpVccTp=csb ---> (U,E) Subrack=MS,Slot=9,PlugInUnit=1 vclTpId Aal5TpVccTp=csb ---> (-,E) AtmPort=MS-7-1,VplTp=vp12,VpcTp=1,VclTp=vc34 atmTrafficDescriptrId AtmPort=MS-7-1,VplTp=vp12,VpcTp=1,VclTp=vc34---> (-,-) AtmTrafficDescriptor=U3P4500M3000 nniSaalTpId Mtp3bSp=1,Mtp3bSls=1,Mtp3bSl=1 ---> (-,E) NniSaalTp=csa nniSaalProfileId NniSaalTp=csa ---> (-,-) NniSaalProfile=1 aal5TpVccTpId NniSaalTp=csa ---> (-,E) Aal5TpVccTp=csa processorId Aal5TpVccTp=csa ---> (U,E) Subrack=MS,Slot=8,PlugInUnit=1 vclTpId Aal5TpVccTp=csa ---> (-,E) AtmPort=MS-6-1,VplTp=vp11,VpcTp=1,VclTp=vc34 atmTrafficDescriptrId AtmPort=MS-6-1,VplTp=vp11,VpcTp=1,VclTp=vc34---> (-,-) AtmTrafficDescriptor=U3P4500M3000 =============================================================================== In the middle column is the originating MO. In the far right column is the referenced MO. In the left column is the attribute containing the referenced MO. The letters in brackets show the admstate and opstate of the referenced MO: U for unlocked, L for locked, E for enabled, D for disabled, "-" for not/applicable. !!!Not all referenced MO's are followed, e.g. some MO's like AtmTrafficDescriptor contain references to very many MO's that don't really relate to the MO you're looking at. The MO's whose references shouldn't be followed are defined at the beginning of moshell in the "dontfollowlist" variable. !!!Some MO's are not linked via an attribute but via parent/child relationship. Those MO's are specified in the "followlist" variable at the beginning of moshell. For instance: To link Mtp3bSls with Mtp3bSl To link IubLink with Nbap,NodeSync, etc. The output prints an empty line, whenever some MO's are referenced via parent/child relationship. RETURN ******************************************************* lt/ltc[1-9] <motype-filter>|root|all [<attribute==value> AND/OR <attribute==value>]

******************************************************* lt stands for "Load mo Types", ltc stands for "Load mo Types and their Children". The numeric option in ltc is for specifyting the number of levels of children to load. Without the option, all levels of children are loaded. This command queries the node to find out which MOs it contains and creates a table with the MO LDNs and a proxy number. The first argument of the lt/ltc command can be: - root: clear the proxy table and allocate a proxy for the root MO (ManagedElement) - all: build a proxy table with all MO's contained in the node. From v4.0, the method used to download all MO references is faster and uses less memory. - <motype-filter>: get a proxy for all MO types matching the specified pattern. For instance: >> lt atmpor ---> all MO's matching the string "atmpor", this will usually be the "AtmPort" MO's >> ltc equipm --> the Equipment MO and all its children (all the way down) >> ltc1 equipm ---> the Equipment MO and one level of children only >> ltc2 transp ---> the TransportNetwork MO and two levels of children only >> lt ^utrancell|fach|rach|pch --> all utrancells, fach, rach, pch MOs >> lt iub --> all iublinks The pattern in motype-filter is a regular expression, more information can be found with command "h syntax" and "h pr". The argument root/all clears the proxy table, whereas lt <motype-filter> doesn't, so the MO LDNs get appended to the existing table. If the same MO type is loaded several times, only the latest fetched instance is kept. Previously fetched instances of that MO type are deleted from the internal table. The second argument (optional) is a filter constraint for the attribute value. For instance: >> lt utrancell operationalstate==0 --> load proxys for all disabled cells >> lt utrancell primarycpichpower==270 --> load proxys for all cells that have pichpower=270 >> lt all operationalstate==0 OR administrativestate==0 --> load proxys for all MOs in the node that have opstate 0 or admstate 0. >> ltc rncfunction operationalstate==0 --> load proxys for all MOs under RncFunction that have opstate 0. Note: This type of search is very hard for the node if it has to search through a large number of MOs (ie several thousand). For more information about Filter constraint, refer to: MO Client Interface User Guide 1553-CXA 104 210. ******************************************************* pr/lpr [<moGroup>|<moFilter>|<proxy(s)>] ******************************************************* This is the print command. It doesn't actually communicate with the node, it justs prints part of the reference table that was fetched by lt/ltc, lc/lcc, or ld command. The print command is useful to test patterns used in mo-filters. For instance, some patterns will match more MO's than you expected, which will result in executing a command on some unwanted MO's. Therefore, it is good to first try your pattern on the pr/lpr command, then do it "for real" on a command that actually communicates with the node. The pr/lpr command also shows the total number of MO's matching the pattern. Example: >> pr ==> print all MOs >> pr 0-1000 ==> print MOs with proxy id 0 to 1000 >> pr !utranrel ==> print all MOs except those with an RDN matching "utranrel" More info in chapter 3 ("h syntax"). RETURN

******************************************************* str ******************************************************* The command has two syntaxes, depending on the type of node. a) CDMA BSC: str [ | <unixCommand>] ------------------------------------------------------------------------------------SITE C1 C2 C3 ABIS BACKHAUL ATMPORTS ------------------------------------------------------------------------------------96 11 11 11 11 RBS1_Backhaul BHRBS1_Backhaul_BHSBackhaulSpan_1 ------------------------------------------------------------------------------------The states of the channels are shown for each cell, as well as the states of the AbisCommon and AbisDedicated. The MO-id of the backhaul and the atmports are also shown for each site. State abbreviation: L means Locked, 0 means Disabled, and 1 means Enabled. b) UTRAN RNC: str[12ft] [<csvfile>] [<filter-options>] [ | <unix cmds>] To see the state of all or part of the cells/iubs/channels in the node, one line per site. The filter options (-m, -s, -i, -c) allow to get states on only part of the sites/cells, in order to speed up the output. Eg: >> str -m 7,8,9 ---> print states only for modules 7, 8, and 9 >> str -s ms,es-1 ---> print states only for subracks ms and es-1 >> str -i 9012 ---> print states only for iublink 9012 and its connected cells >> str -c 90121,90131 --> print states only for the sites connected to cell 90121 and 90131 There are four possible output formats: The "str" printout uses an abbreviated naming of the cells where it is assumed that the last digit is identifying the sector. For networks where the sector is not identified by the last digit, it can be handy to use "str1" or "str2" since the whole cell name will then be shown for each sector. The "strt" command shows the AtmPorts used by each site. - str ------------------------------------------------------------------------------------MOD IUBLINK CELLNAME CELL1 CELL2 CELL3 CD12 ------------------------------------------------------------------------------------ 1 Iub_3011 3011-1/2/3 1111 L000 1000 1111 ------------------------------------------------------------------------------------ - strt ------------------------------------------------------------------------------------MOD IUBLINK CELLNAME CELL1 CELL2 CELL3 CD12 ATMPORTS ------------------------------------------------------------------------------------ 1 Iub_3011 3011-1/2/3 1111 L000 1000 1111 MS-26-1 ------------------------------------------------------------------------------------ - str1 ------------------------------------------------------------------------------------MOD IUBLINK CELLNAMES CELL1 CELL2 CELL3 CD12 ------------------------------------------------------------------------------------ 1 Iub_3011 30111 30112 30113 1111 1111 1111 1111 ------------------------------------------------------------------------------------ - str2 ------------------------------------------------------------------------------------MOD IUBLINK CD12 CELL1 CRFP CELL2 CRFP CELL3 CRFP ------------------------------------------------------------------------------------ 1 Iub_3011 1111 30111 1111 30112 1111 30113 1111

------------------------------------------------------------------------------------MOD: this the RNC module that the site is defined in. IUBLINK: this is the identity of the iublink that the site is using. CELLNAME: this is the name of the cells that are connected to that IubLink. the cell names correspond to the respective sectors. eg: 6306-1/2/3 means that: cell 63061 is connected to SECT1 cell 63062 is connected to SECT2 cell 63063 is connected to SECT3. CELL: the first digit is the state of the cell. the three following digits are the state of the common channels (fach/rach/pch). the fifth digit (if present) represents the state of the hsdpa channel (hsdsch). the sixth digit (if present) represents the state of the enhanced uplink channel (eul). CD12: the first digit is the state of nbapCommon the second digit is the state of nbapDedicated the final two digits are the states of NodeSynchTp 1 and 2. States: L means Locked, 0 means Disabled, and 1 means Enabled. The output can be piped in external unix commands such as grep. If a filename is given as argument, the output will be saved into this file in csv format (as well as being printed on the screen). The f option ("fast") is for printing without fetching the data. Ie, the data can be fetched once, then displayed in many different ways without having to fetch it again each time. Examples: >> strf | grep 3011 >> str1f | sort +1 (sort on the second field) RETURN ******************************************************* ma/lma <moGroup> <moGroup>|<moFilter>|<proxy(s)>|all [<attribute-filter>] [<value-filter>] ******************************************************* To put MO LDNs into an MO-Group. The first argument (mandatory) indicates the name of the MO-Group. The second argument (mandatory) indicates the Proxy Id's or MO-Filter of the MOs to match. If no further arguments are given then the MOs whose RDN/LDN match the MO-filter (or who have the corresponding proxy) will be put in the MO-Group. If further arguments are given then a get or pget command is performed using the second/third(/fourth) argument of the ma/lma command. The third argument will be a string to match the attribute and the fourth (if it's used) will match the value. If the attribute is of any other type than MoRef, then the MO(s) whose attribute match the fourth argument will be put in the group. If the attribute is of type MoRef, then the MO(s) contained in the attribute is put in the group (except if there is a fourth argument). Examples: >> ma test atmport.*24-1 ==> all MOs whose RDN match atmport.*24-1 are put in the group called "test" >> lma test atmport.*24-1 ==> all MOs whose LDN match atmport.*24-1 are put in the group called "test" >> ma test atmport operationalst 0 ==> all MOs whose RDN match "atmport" and who have operationalstate matching "0" will be put in the group "test" >> ma test atmport physpathterm ==> all MOs who are referenced through the attribute "physpathermId" of the MOs matching "atmport" will be put in the group "test" (since physpathermId is an attribute of type MoRef) >> lma test subrack=ms,slot=10,program loadmodule ==> all loadmodule MOs connected to program MOs running on slot 10 in main subrack will be put in the group "test" (since "loadmodule" is an attribute of type MoRef) >> ma test atmport physpatherm slot=23 ==> all atmports whose physpatherm reference matches "slot=23" will be put in the group >> ma test reliableprogram admactiveslot slot=10 ==> all reliableprograms that are on slot 10 will be put in the group >> ma test vcltp pmrec 0 ==> all vcltps with 0 pmreceivedcells are put in the group

Two-step examples: 1. to put all unlocked-disabled MOs in a group in order to lock them >> ma test all operational 0 >> ma test1 test administ 1 >> bl test1 2. to put all cells belonging to module 3 in a group in order to lock them >> ma iubmod3 iublink module =3$ >> ma cellmod3 iubmod3 reservedby >> bl cellmod3 3. to put all vcltps that have 0 receivedcells and more than 0 transmitted cells in a group in order to find out which upper layers are affected >> ma faultyvcltp vcltp pmrec ^0$ >> mr faultyvcltp vcltp pmtrans ^[^0] >> lk faultyvcltp RETURN ******************************************************* ftget[c]/ftput[c] ******************************************************* This command allows to do an ftp put/get between the cello node and the workstation. Syntax: * ftput[c] localfile/localdir [remotefile/remotedir] * ftget[c] remotefile/remotedir [localfile/localdir] Where "local" refers to the workstation and "remote" refers to the cello node. It is possible to download/upload a whole directory from/to the node by specifying a remote/local directory instead of a remote/local file. The "c" option stands for conditional and means that if the file already exists on the workstation/node, it will not be overwritten. By running ftput/ftget from mobatch, it is possible to get/put files to/from many nodes in parallel. Limitations: * Wildcards (*) are currently not supported. * Only active mode is supported for unsecure ftp. If active mode is not allowed by the firewall, then use secure_ftp instead (see chap 0.5 for info about secure_shell/secure_ftp). ******************************************************* fro/lfro[m] <moGroup>|<moFilter>|<proxy(s)>|all [<attribute-filter>|all] [<value-filter>] ******************************************************* To print the froid(s) of an MO. The froid is found by reading the modata_r1 sql table in the node. The "m" option is for printing all MAO attributes of the MO (including the froid). Same format as for the get command. Examples: >> fro plugin --> print all froids for all pluginunits (will show resourceid and sairesourceid) >> fro plugin ^r --> print the resourceid for all pluginunits >> fro plugin . 5 --> print only the MOs who have a froid matching the value 5 >> fro plugin . ^5$ ---> print only the MOs who have a froid of 5 exactly >> lfro ms,slot=10,plugin sairesource > $sai --> save the sairesourceid of a particular pluginunit into a variable "$sai" How it works: This command requires read access to the node database using the node's SQL client. If the SQL client LM (CXC1325608) is not started, the fro command will start it automatically using the "sql+/sql-" functionality in moshell (refer to help for these commands for more info). Once the SQL client is running on the node, the fro command will query the tables motype_r1 and modata_r2 in order to find out the froid(s) for the MOs in question.

If the motype_r1 table is not present on the node, it could be that the node SW is too old (eg: Cello 3 or lower). NOTE: As explained in the Tutorial section of the MoShell User Guide, not all MOs have a corresponding fRO related to them.

APPENDIX C: IMA GROUP HANG RETURN IMAGROUP DISABLED FOR GRY502 3RR01> lt aal 3RR01> lst b1013 070524-05:11:09 172.24.12.207 7.0 RESTRICTED RNC_NODE_MODEL_F_5_2 stopfile=/tmp/19957 ======================================================================= Proxy Adm State Op. State MO ======================================================================= 10683 0 (DISABLED) TransportNetwork=1,AtmCrossConnection=b1013ia 10684 0 (DISABLED) TransportNetwork=1,AtmCrossConnection=b1013ib 11492 1 (UNLO 0 (DISABLED) TransportNetwork=1,Aal2PathVccTp=b1013a1 11493 1 (UNLO 0 (DISABLED) TransportNetwork=1,Aal2PathVccTp=b1013a2 13443 0 (DISABLED) TransportNetwork=1,Aal5TpVccTp=b1013qa 13444 0 (DISABLED) TransportNetwork=1,Aal5TpVccTp=b1013qb 13445 0 (DISABLED) TransportNetwork=1,Aal5TpVccTp=b1013ca 13446 0 (DISABLED) TransportNetwork=1,Aal5TpVccTp=b1013cb 13447 0 (DISABLED) TransportNetwork=1,Aal5TpVccTp=b1013da 13448 0 (DISABLED) TransportNetwork=1,Aal5TpVccTp=b1013db 14165 0 (DISABLED) TransportNetwork=1,Aal0TpVccTp=b1013sa1 14166 0 (DISABLED) TransportNetwork=1,Aal0TpVccTp=b1013sb1 14416 0 (DISABLED) TransportNetwork=1,Aal2Sp=1,Aal2Ap=b1013 16091 0 (DISABLED) TransportNetwork=1,UniSaalTp=b1013qa 16092 0 (DISABLED) TransportNetwork=1,UniSaalTp=b1013qb 16093 0 (DISABLED) TransportNetwork=1,UniSaalTp=b1013ca 16094 0 (DISABLED) TransportNetwork=1,UniSaalTp=b1013cb 16095 0 (DISABLED) TransportNetwork=1,UniSaalTp=b1013da 16096 0 (DISABLED) TransportNetwork=1,UniSaalTp=b1013db =======================================================================Total: 19 MOs 3RR01> lst gry502 070524-05:11:25 172.24.12.207 7.0 RESTRICTED RNC_NODE_MODEL_F_5_2 stopfile=/tmp/19957 ======================================================================= Proxy Adm State Op. State MO ======================================================================= 2049 1 (UN) 0 (DSBLD) RncFunction=1,UtranCell=GRY502A,Rach=1 2050 1 (UN) 0 (DISABLED) RncFunction=1,UtranCell=GRY502B,Rach=1 2051 1 (UN) 0 (DISABLED) RncFunction=1,UtranCell=GRY502C,Rach=1 4284 1 (UN) 0 (DISABLED) RncFunction=1,UtranCell=GRY502A,Hsdsch=1 4285 1 (UN) 0 (DISABLED) RncFunction=1,UtranCell=GRY502B,Hsdsch=1 4286 1 (UN) 0 (DISABLED) RncFunction=1,UtranCell=GRY502C,Hsdsch=1 5163 1 (UN) 0 (DISABLED) RncFunction=1,UtranCell=GRY502A,Pch=1 5164 1 (UN) 0 (DISABLED) RncFunction=1,UtranCell=GRY502B,Pch=1 5165 1 (UN) 0 (DISABLED) RncFunction=1,UtranCell=GRY502C,Pch=1 6042 1 (UN) 0 (DISABLED) RncFunction=1,UtranCell=GRY502A,Fach=1 6043 1 (UN) 0 (DISABLED) RncFunction=1,UtranCell=GRY502B,Fach=1 6044 1 (UN) 0 (DISABLED) RncFunction=1,UtranCell=GRY502C,Fach=1 6337 1 (UN) 0 (DSBLD) RncFunction=1,IubLink=Iub_GRY502,NbapCommon=1 8598 1 (UN) 1 (ENBLD) RncFunction=1,IubLink=Iub_GRY502,NodeSynchTp=1 8599 1 (UN) 1 (ENBLD) RncFunction=1,IubLink=Iub_GRY502,NodeSynchTp=2 8892 1 (UN) 0 (DSBLD) RncFunction=1,IubLink=Iub_GRY502,NbapDedicated=1 9185 1 (ENABLED) RncFunction=1,IubLink=Iub_GRY502

10062 1 (UN) 0 (DISABLED) RncFunction=1,UtranCell=GRY502A 10063 1 (UN) 0 (DISABLED) RncFunction=1,UtranCell=GRY502B 10064 1 (UNLOCKED) 0 (DISABLED) RncFunction=1,UtranCell=GRY502C =======================================================================Total: 20 MOs /* ETM Board restart */ 3RR01> alt Nr of active alarms are: 179 =======================================================================Date & Time (Local) S Specific Problem Cause Mo-Reference =======================================================================2007-05-19 19:05:47 w IMA Link Reception Unusable at Far End remote_node_transmission_error ImaGroup=ES-2-2-1-ima48,ImaLink=1 2007-05-19 19:05:48 w IMA Link Reception Unusable at Far End remote_node_transmission_error ImaGroup=ES-2-2-1-ima48,ImaLink=2 2007-05-19 19:05:48 w Remote Defect Indication on IMA Link remote_node_transmission_error ImaGroup=ES-2-2-1-ima48,ImaLink=2 2007-05-19 19:05:49 M IMA Group Insufficient Links at Far End remote_node_transmission_error ImaGroup=ES-2-2-1-ima48 2007-05-19 19:05:49 M IMA Group Insufficient Links local_node_transmission_error ImaGroup=ES-2-2-1-ima48 2007-05-21 15:36:58 w IMA Link Reception Unusable at Far End remote_node_transmission_error ImaGroup=ES-2-2-1-ima3,ImaLink=1 2007-05-24 05:51:14 M UtranCell_ServiceUnavailable unavailable UtranCell=GRY021C 2007-05-24 05:51:14 M UtranCell_ServiceUnavailable unavailable UtranCell=GRY021A 2007-05-24 05:51:14 M UtranCell_ServiceUnavailable unavailable UtranCell=GRY744C 2007-05-24 05:51:14 M UtranCell_ServiceUnavailable unavailable UtranCell=GRY744A 2007-05-24 05:51:14 M UtranCell_ServiceUnavailable unavailable UtranCell=GRY744B 2007-05-24 05:51:14 M UtranCell_ServiceUnavailable unavailable UtranCell=GRI836A 2007-05-24 05:51:14 M UtranCell_ServiceUnavailable unavailable UtranCell=GRY021B 2007-05-24 05:51:15 M UtranCell_ServiceUnavailable unavailable UtranCell=GRY575A 2007-05-24 05:51:15 M UtranCell_ServiceUnavailable unavailable UtranCell=GRY844B 2007-05-24 05:51:15 M UtranCell_ServiceUnavailable unavailable UtranCell=GRY844C 2007-05-24 05:51:15 M UtranCell_ServiceUnavailable unavailable UtranCell=GRY844A 2007-05-24 05:51:15 M UtranCell_ServiceUnavailable unavailable UtranCell=GRI836B 2007-05-24 05:51:15 M UtranCell_ServiceUnavailable unavailable UtranCell=GRI836C 2007-05-24 05:51:16 M UtranCell_ServiceUnavailable unavailable UtranCell=GRY770B 2007-05-24 05:51:16 M UtranCell_ServiceUnavailable unavailable UtranCell=GRY770C 2007-05-24 05:51:16 M UtranCell_ServiceUnavailable unavailable UtranCell=GRY770A 2007-05-24 05:51:16 M UtranCell_ServiceUnavailable unavailable UtranCell=GRY271B 2007-05-24 05:51:16 M UtranCell_ServiceUnavailable unavailable UtranCell=GRY271C 2007-05-24 05:51:16 M UtranCell_ServiceUnavailable unavailable UtranCell=GRY271A 2007-05-24 05:51:16 M UtranCell_ServiceUnavailable unavailable UtranCell=GRY116A

2007-05-24 05:51:16 M UtranCell_ServiceUnavailable unavailable UtranCell=GRY116C 2007-05-24 05:51:16 M UtranCell_ServiceUnavailable unavailable UtranCell=GRY116B 2007-05-24 05:51:16 M UtranCell_ServiceUnavailable unavailable UtranCell=GRY575B 2007-05-24 05:51:16 M UtranCell_ServiceUnavailable unavailable UtranCell=GRY575C 2007-05-24 05:52:06 m CchFrameSynch_TimingAdjCtrlFrame timing_problem_m3100 CchFrameSynch=1 2007-05-24 05:52:22 M Pch_InternalResourceUnavailable unavailable UtranCell=GRY896B,Pch=1 2007-05-24 05:52:22 M Fach_InternalResourceUnavailable unavailable UtranCell=GRY896C,Fach=1 2007-05-24 05:52:22 M Rach_InternalResourceUnavailable unavailable UtranCell=GRY896A,Rach=1 2007-05-24 05:52:22 M Rach_InternalResourceUnavailable unavailable UtranCell=GRY896B,Rach=1 2007-05-24 05:52:22 M Pch_InternalResourceUnavailable unavailable UtranCell=GRY896A,Pch=1 2007-05-24 05:52:22 M Fach_InternalResourceUnavailable unavailable UtranCell=GRY896B,Fach=1 2007-05-24 05:52:22 M Fach_InternalResourceUnavailable unavailable UtranCell=GRY896A,Fach=1 2007-05-24 05:52:22 M Rach_InternalResourceUnavailable unavailable UtranCell=GRY896C,Rach=1 2007-05-24 05:52:23 M Pch_InternalResourceUnavailable unavailable UtranCell=GRY896C,Pch=1 2007-05-24 05:52:24 M Rach_InternalResourceUnavailable unavailable UtranCell=GRY766A,Rach=1 2007-05-24 05:52:24 M Pch_InternalResourceUnavailable unavailable UtranCell=GRY066A,Pch=1 2007-05-24 05:52:24 M Fach_InternalResourceUnavailable unavailable UtranCell=GRY066B,Fach=1 2007-05-24 05:52:24 M Rach_InternalResourceUnavailable unavailable UtranCell=GRY066A,Rach=1 2007-05-24 05:52:24 M Fach_InternalResourceUnavailable unavailable UtranCell=GRY545B,Fach=1 2007-05-24 05:52:24 M Rach_InternalResourceUnavailable unavailable UtranCell=GRY066C,Rach=1 2007-05-24 05:52:24 M Rach_InternalResourceUnavailable unavailable UtranCell=GRY766C,Rach=1 2007-05-24 05:52:24 M Pch_InternalResourceUnavailable unavailable UtranCell=GRY066C,Pch=1 2007-05-24 05:52:24 M Pch_InternalResourceUnavailable unavailable UtranCell=GRY066B,Pch=1 2007-05-24 05:52:24 M Fach_InternalResourceUnavailable unavailable UtranCell=GRY066C,Fach=1 2007-05-24 05:52:24 M Pch_InternalResourceUnavailable unavailable UtranCell=GRY766A,Pch=1 2007-05-24 05:52:24 M Fach_InternalResourceUnavailable unavailable UtranCell=GRY766B,Fach=1 2007-05-24 05:52:24 M Pch_InternalResourceUnavailable unavailable UtranCell=GRY545C,Pch=1 2007-05-24 05:52:24 M Fach_InternalResourceUnavailable unavailable UtranCell=GRY766C,Fach=1 2007-05-24 05:52:24 M Pch_InternalResourceUnavailable unavailable UtranCell=GRY545B,Pch=1 2007-05-24 05:52:24 M Fach_InternalResourceUnavailable unavailable UtranCell=GRY766A,Fach=1 2007-05-24 05:52:24 M Rach_InternalResourceUnavailable unavailable UtranCell=GRY545B,Rach=1 2007-05-24 05:52:24 M Pch_InternalResourceUnavailable unavailable UtranCell=GRY766B,Pch=1

2007-05-24 05:52:24 M Rach_InternalResourceUnavailable unavailable UtranCell=GRY545A,Rach=1 2007-05-24 05:52:24 M Rach_InternalResourceUnavailable unavailable UtranCell=GRY545C,Rach=1 2007-05-24 05:52:24 M Pch_InternalResourceUnavailable unavailable UtranCell=GRY545A,Pch=1 2007-05-24 05:52:24 M Rach_InternalResourceUnavailable unavailable UtranCell=GRY066B,Rach=1 2007-05-24 05:52:24 M Fach_InternalResourceUnavailable unavailable UtranCell=GRY545C,Fach=1 2007-05-24 05:52:24 M Fach_InternalResourceUnavailable unavailable UtranCell=GRY545A,Fach=1 2007-05-24 05:52:24 M Fach_InternalResourceUnavailable unavailable UtranCell=GRY066A,Fach=1 2007-05-24 05:52:26 M Fach_InternalResourceUnavailable unavailable UtranCell=GRY087A,Fach=1 2007-05-24 05:52:26 M Pch_InternalResourceUnavailable unavailable UtranCell=GRY022C,Pch=1 2007-05-24 05:52:26 M Fach_InternalResourceUnavailable unavailable UtranCell=GRY022A,Fach=1 2007-05-24 05:52:26 M Pch_InternalResourceUnavailable unavailable UtranCell=GRY022B,Pch=1 2007-05-24 05:52:26 M Fach_InternalResourceUnavailable unavailable UtranCell=GRY022C,Fach=1 2007-05-24 05:52:26 M Fach_InternalResourceUnavailable unavailable UtranCell=GRY022B,Fach=1 2007-05-24 05:52:26 M Rach_InternalResourceUnavailable unavailable UtranCell=GRY022C,Rach=1 2007-05-24 05:52:26 M Rach_InternalResourceUnavailable unavailable UtranCell=GRY022A,Rach=1 2007-05-24 05:52:26 M Rach_InternalResourceUnavailable unavailable UtranCell=GRY766B,Rach=1 2007-05-24 05:52:26 M Pch_InternalResourceUnavailable unavailable UtranCell=GRY766C,Pch=1 2007-05-24 05:52:26 M Fach_InternalResourceUnavailable unavailable UtranCell=GRY248B,Fach=1 2007-05-24 05:52:26 M Fach_InternalResourceUnavailable unavailable UtranCell=GRY087B,Fach=1 2007-05-24 05:52:26 M Fach_InternalResourceUnavailable unavailable UtranCell=GRY249C,Fach=1 2007-05-24 05:52:26 M Pch_InternalResourceUnavailable unavailable UtranCell=GRY249A,Pch=1 2007-05-24 05:52:26 M Rach_InternalResourceUnavailable unavailable UtranCell=GRY248C,Rach=1 2007-05-24 05:52:26 M Fach_InternalResourceUnavailable unavailable UtranCell=GRY248A,Fach=1 2007-05-24 05:52:26 M Rach_InternalResourceUnavailable unavailable UtranCell=GRY248B,Rach=1 2007-05-24 05:52:26 M Rach_InternalResourceUnavailable unavailable UtranCell=GRY087C,Rach=1 2007-05-24 05:52:26 M Rach_InternalResourceUnavailable unavailable UtranCell=GRY248A,Rach=1 2007-05-24 05:52:26 M Rach_InternalResourceUnavailable unavailable UtranCell=GRY087B,Rach=1 2007-05-24 05:52:26 M Rach_InternalResourceUnavailable unavailable UtranCell=GRY087A,Rach=1 2007-05-24 05:52:26 M Rach_InternalResourceUnavailable unavailable UtranCell=GRY022B,Rach=1 2007-05-24 05:52:26 M Fach_InternalResourceUnavailable unavailable UtranCell=GRY087C,Fach=1 2007-05-24 05:52:26 M Pch_InternalResourceUnavailable unavailable UtranCell=GRY022A,Pch=1 2007-05-24 05:52:28 M Fach_InternalResourceUnavailable unavailable UtranCell=GRY248C,Fach=1

2007-05-24 05:52:28 M Fach_InternalResourceUnavailable unavailable UtranCell=GRY249A,Fach=1 2007-05-24 05:52:28 M Fach_InternalResourceUnavailable unavailable UtranCell=GRY249B,Fach=1 2007-05-24 05:52:28 M Rach_InternalResourceUnavailable unavailable UtranCell=GRY249B,Rach=1 2007-05-24 05:52:28 M Fach_InternalResourceUnavailable unavailable UtranCell=GRY279B,Fach=1 2007-05-24 05:52:28 M Pch_InternalResourceUnavailable unavailable UtranCell=GRY249C,Pch=1 2007-05-24 05:52:28 M Fach_InternalResourceUnavailable unavailable UtranCell=GRY279C,Fach=1 2007-05-24 05:52:28 M Pch_InternalResourceUnavailable unavailable UtranCell=GRY249B,Pch=1 2007-05-24 05:52:28 M Fach_InternalResourceUnavailable unavailable UtranCell=GRY279A,Fach=1 2007-05-24 05:52:28 M Rach_InternalResourceUnavailable unavailable UtranCell=GRY279B,Rach=1 2007-05-24 05:52:29 M Rach_InternalResourceUnavailable unavailable UtranCell=GRY119B,Rach=1 2007-05-24 05:52:29 M Pch_InternalResourceUnavailable unavailable UtranCell=GRY087B,Pch=1 2007-05-24 05:52:29 M Pch_InternalResourceUnavailable unavailable UtranCell=GRY119C,Pch=1 2007-05-24 05:52:29 M Pch_InternalResourceUnavailable unavailable UtranCell=GRY248C,Pch=1 2007-05-24 05:52:29 M Pch_InternalResourceUnavailable unavailable UtranCell=GRY087A,Pch=1 2007-05-24 05:52:29 M Pch_InternalResourceUnavailable unavailable UtranCell=GRY248B,Pch=1 2007-05-24 05:52:29 M Pch_InternalResourceUnavailable unavailable UtranCell=GRY279C,Pch=1 2007-05-24 05:52:29 M Rach_InternalResourceUnavailable unavailable UtranCell=GRY119C,Rach=1 2007-05-24 05:52:29 M Pch_InternalResourceUnavailable unavailable UtranCell=GRY119A,Pch=1 2007-05-24 05:52:29 M Pch_InternalResourceUnavailable unavailable UtranCell=GRY279B,Pch=1 2007-05-24 05:52:29 M Pch_InternalResourceUnavailable unavailable UtranCell=GRY279A,Pch=1 2007-05-24 05:52:29 M Rach_InternalResourceUnavailable unavailable UtranCell=GRY249C,Rach=1 2007-05-24 05:52:29 M Rach_InternalResourceUnavailable unavailable UtranCell=GRY279C,Rach=1 2007-05-24 05:52:29 M Fach_InternalResourceUnavailable unavailable UtranCell=GRY230C,Fach=1 2007-05-24 05:52:29 M Fach_InternalResourceUnavailable unavailable UtranCell=GRY230A,Fach=1 2007-05-24 05:52:29 M Pch_InternalResourceUnavailable unavailable UtranCell=GRY442C,Pch=1 2007-05-24 05:52:29 M Rach_InternalResourceUnavailable unavailable UtranCell=GRY442B,Rach=1 2007-05-24 05:52:29 M Fach_InternalResourceUnavailable unavailable UtranCell=GRY442C,Fach=1 2007-05-24 05:52:29 M Fach_InternalResourceUnavailable unavailable UtranCell=GRY119A,Fach=1 2007-05-24 05:52:29 M Pch_InternalResourceUnavailable unavailable UtranCell=GRY248A,Pch=1 2007-05-24 05:52:29 M Pch_InternalResourceUnavailable unavailable UtranCell=GRY119B,Pch=1 2007-05-24 05:52:29 M Pch_InternalResourceUnavailable unavailable UtranCell=GRY087C,Pch=1 2007-05-24 05:52:29 M Fach_InternalResourceUnavailable unavailable UtranCell=GRY119C,Fach=1

2007-05-24 05:52:29 M Fach_InternalResourceUnavailable unavailable UtranCell=GRY119B,Fach=1 2007-05-24 05:52:29 M Rach_InternalResourceUnavailable unavailable UtranCell=GRY119A,Rach=1 2007-05-24 05:52:29 M Rach_InternalResourceUnavailable unavailable UtranCell=GRY249A,Rach=1 2007-05-24 05:52:29 M Rach_InternalResourceUnavailable unavailable UtranCell=GRY279A,Rach=1 2007-05-24 05:52:31 M Rach_InternalResourceUnavailable unavailable UtranCell=GRY442A,Rach=1 2007-05-24 05:52:31 M Pch_InternalResourceUnavailable unavailable UtranCell=GRY442B,Pch=1 2007-05-24 05:52:31 M Rach_InternalResourceUnavailable unavailable UtranCell=GRY230C,Rach=1 2007-05-24 05:52:31 M Pch_InternalResourceUnavailable unavailable UtranCell=GRY230A,Pch=1 2007-05-24 05:52:31 M Fach_InternalResourceUnavailable unavailable UtranCell=GRY442B,Fach=1 2007-05-24 05:52:31 M Pch_InternalResourceUnavailable unavailable UtranCell=GRY798C,Pch=1 2007-05-24 05:52:31 M Fach_InternalResourceUnavailable unavailable UtranCell=GRY442A,Fach=1 2007-05-24 05:52:31 M Pch_InternalResourceUnavailable unavailable UtranCell=GRY798A,Pch=1 2007-05-24 05:52:31 M Fach_InternalResourceUnavailable unavailable UtranCell=GRY798A,Fach=1 2007-05-24 05:52:31 M Rach_InternalResourceUnavailable unavailable UtranCell=GRY442C,Rach=1 2007-05-24 05:52:31 M Rach_InternalResourceUnavailable unavailable UtranCell=GRY798B,Rach=1 2007-05-24 05:52:31 M Pch_InternalResourceUnavailable unavailable UtranCell=GRY798B,Pch=1 2007-05-24 05:52:31 M Rach_InternalResourceUnavailable unavailable UtranCell=GRY798A,Rach=1 2007-05-24 05:52:31 M Rach_InternalResourceUnavailable unavailable UtranCell=GRY230A,Rach=1 2007-05-24 05:52:31 M Fach_InternalResourceUnavailable unavailable UtranCell=GRY230B,Fach=1 2007-05-24 05:52:31 M Rach_InternalResourceUnavailable unavailable UtranCell=GRY798C,Rach=1 2007-05-24 05:52:31 M Fach_InternalResourceUnavailable unavailable UtranCell=GRY798C,Fach=1 2007-05-24 05:52:31 M Fach_InternalResourceUnavailable unavailable UtranCell=GRY798B,Fach=1 2007-05-24 05:52:31 M Pch_InternalResourceUnavailable unavailable UtranCell=GRY230B,Pch=1 2007-05-24 05:52:31 M Pch_InternalResourceUnavailable unavailable UtranCell=GRY230C,Pch=1 2007-05-24 05:52:31 M Rach_InternalResourceUnavailable unavailable UtranCell=GRY230B,Rach=1 2007-05-24 05:52:31 M Pch_InternalResourceUnavailable unavailable UtranCell=GRY442A,Pch=1 2007-05-24 05:52:45 M NbapDedicated_RncRbsControlLinkDown transmission_error IubLink=Iub_GRY116,NbapDedicated=1 2007-05-24 05:52:45 M NbapDedicated_RncRbsControlLinkDown transmission_error IubLink=Iub_GRY907,NbapDedicated=1 2007-05-24 05:52:45 M NbapDedicated_RncRbsControlLinkDown transmission_error IubLink=Iub_GRY575,NbapDedicated=1 2007-05-24 05:52:46 M NbapDedicated_RncRbsControlLinkDown transmission_error IubLink=Iub_GRY844,NbapDedicated=1 2007-05-24 05:52:46 M NbapDedicated_RncRbsControlLinkDown transmission_error IubLink=Iub_GRY021,NbapDedicated=1 2007-05-24 05:52:46 M NbapDedicated_RncRbsControlLinkDown transmission_error IubLink=Iub_GRY770,NbapDedicated=1

2007-05-24 05:52:46 M NbapDedicated_RncRbsControlLinkDown transmission_error IubLink=Iub_GRI836,NbapDedicated=1 2007-05-24 05:52:46 M NbapDedicated_RncRbsControlLinkDown transmission_error IubLink=Iub_GRY744,NbapDedicated=1 2007-05-24 05:52:46 M NbapDedicated_RncRbsControlLinkDown transmission_error IubLink=Iub_GRY271,NbapDedicated=1 2007-05-24 05:52:47 M NbapDedicated_RncRbsControlLinkDown transmission_error IubLink=Iub_GCW616,NbapDedicated=1 2007-05-24 05:55:36 M UtranCell_ServiceUnavailable unavailable UtranCell=GRY024B 2007-05-24 05:55:37 M UtranCell_ServiceUnavailable unavailable UtranCell=GRY846B 2007-05-24 05:55:37 M UtranCell_ServiceUnavailable unavailable UtranCell=GRY846C 2007-05-24 05:55:37 M UtranCell_ServiceUnavailable unavailable UtranCell=GRY846A 2007-05-24 05:55:37 M UtranCell_ServiceUnavailable unavailable UtranCell=GRY295C 2007-05-24 05:55:37 M UtranCell_ServiceUnavailable unavailable UtranCell=GRY295A 2007-05-24 05:55:37 M UtranCell_ServiceUnavailable unavailable UtranCell=GRY295B 2007-05-24 05:55:37 M UtranCell_ServiceUnavailable unavailable UtranCell=GRY853B 2007-05-24 05:55:37 M UtranCell_ServiceUnavailable unavailable UtranCell=GRY853C 2007-05-24 05:55:37 M UtranCell_ServiceUnavailable unavailable UtranCell=GRY853A 2007-05-24 05:55:37 M UtranCell_ServiceUnavailable unavailable UtranCell=GRY024A 2007-05-24 05:55:37 M UtranCell_ServiceUnavailable unavailable UtranCell=GRY024C 2007-05-24 05:55:39 M UtranCell_ServiceUnavailable unavailable UtranCell=GRY332B 2007-05-24 05:55:39 M UtranCell_ServiceUnavailable unavailable UtranCell=GRY332A 2007-05-24 05:55:39 M UtranCell_ServiceUnavailable unavailable UtranCell=GRY332C 2007-05-24 05:55:39 M UtranCell_ServiceUnavailable unavailable UtranCell=GRY064A 2007-05-24 05:55:39 M UtranCell_ServiceUnavailable unavailable UtranCell=GRY064C 2007-05-24 05:55:39 M UtranCell_ServiceUnavailable unavailable UtranCell=GRY064B 2007-05-24 05:55:39 M UtranCell_ServiceUnavailable unavailable UtranCell=GRI880C 2007-05-24 05:55:39 M UtranCell_ServiceUnavailable unavailable UtranCell=GRI880A 2007-05-24 05:55:39 M UtranCell_ServiceUnavailable unavailable UtranCell=GRI880B >>> Total: 179 Alarms (0 Critical, 174 Major) /* Some sites did not recover after restart, require another restart */ 3RR01> strt Following 228 sites are up: -----------------------------------------------------------------------------------------------MOD IUBLINK CELLNAMES CELL1 CELL2 CELL3 CD12 ATMPORTS ----------------------------------------------------------------------------------------------- 1 Iub_GRY292 GRY292-A/B/C 1111 1111 1111 1111 MS-26-1:vp1 1 Iub_GRY981 GRY981-A/B/C 11111 11111 11111 1111 MS-26-1:vp1 1 Iub_GRY316 GRY316-A/B/C 1111 1111 1111 1111 ES-1-2-1-8:vp1 1 Iub_GRY297 GRY297-A/B/C 1111 1111 1111 1111 ES-1-2-1-7:vp1 1 Iub_GRY106 GRY106-A/B/C 1111 1111 1111 1111 MS-26-1:vp1

1 Iub_GRY565 GRY565-A/B/C 11111 11111 11111 1111 MS-26-1:vp1 1 Iub_GRY394 GRY394-A/B/C 11111 11111 11111 1111 ES-1-2-1-10:vp1 1 Iub_GRY398 GRY398-A/B/C 1111 1111 1111 1111 ES-1-2-1-9:vp1 1 Iub_GRY899 GRY899-A/B/C 1111 1111 1111 1111 MS-26-1:vp1 1 Iub_GRY303 GRY303-A/B/C 11111 11111 11111 1111 MS-26-1:vp1 1 Iub_GRY309 GRY309-A/B/C 11111 11111 11111 1111 MS-26-1:vp1 1 Iub_GRY994 GRY994-A/B/C 11111 11111 11111 1111 MS-26-1:vp1 1 Iub_GRY429 GRY429-A/B/C 11111 11111 11111 1111 MS-26-1:vp1 1 Iub_GRY235 GRY235-A/B/C 11111 11111 11111 1111 ES-1-2-1-6:vp1 1 Iub_GRY238 GRY238-A/B/C 11111 11111 11111 1111 MS-26-1:vp1 1 Iub_GRY480 GRY480-A/B/C 1111 1111 1111 1111 MS-26-1:vp1 2 Iub_GRY062 GRY062-A/B/C 11111 11111 11111 1111 MS-24-1:vp1 2 Iub_GRY524 GRY524-A/B/C 11111 11111 11111 1111 ES-1-2-1-53:vp1 2 Iub_GRY296 GRY296-A/B/C 1111 1111 1111 1111 MS-26-1:vp1 2 Iub_GRY108 GRY108-A/B/C 11111 11111 11111 1111 MS-27-2:vp1 2 Iub_GRY795 GRY795-A/B/C 1111 1111 1111 1111 ES-1-26-1-ima40:vp1 2 Iub_GRY016 GRY016-A/B/C 1111 1111 1111 1111 MS-26-1:vp1 2 Iub_GRY704 GRY704-A/B/C 11111 11111 11111 1111 ES-1-2-1-55:vp1 2 Iub_GRY244 GRY244-A/B/C 11111 11111 11111 1111 MS-27-2:vp1 2 Iub_GRY264 GRY264-A/B/C 11111 11111 11111 1111 MS-26-1:vp1 2 Iub_GRY975 GRY975-A/B/C 1111 1111 1111 1111 MS-24-1:vp1 2 Iub_GRY536 GRY536-A/B/C 11111 11111 11111 1111 MS-24-1:vp1 2 Iub_GRY382 GRY382-A/B/C 1111 1111 1111 1111 MS-24-1:vp1 2 Iub_GRY617 GRY617-A/B/C 11111 11111 11111 1111 ES-1-2-1-51:vp1 2 Iub_GRY863 GRY863-A/B/C 11111 11111 11111 1111 ES-1-2-1-56:vp1 2 Iub_GRY445 GRY445-A/B/C 11111 11111 11111 1111 MS-24-1:vp1 2 Iub_GRY028 GRY028-A/B/C 11111 11111 11111 1111 ES-2-2-1-22:vp1 2 Iub_GRY041 GRY041-A/B/C 11111 11111 11111 1111 ES-1-26-1-ima17:vp1 2 Iub_GRY029 GRY029-A/B/C 1111 1111 1111 1111 ES-1-26-1-ima19:vp1 3 Iub_GRY359 GRY359-A/B/C 11111 11111 11111 1111 MS-24-1:vp1 3 Iub_GRY857 GRY857-A/B/C 1111 1111 1111 1111 MS-24-1:vp1 3 Iub_GRY206 GRY206-A/B/C 11111 11111 11111 1111 MS-24-1:vp1 3 Iub_GRY188 GRY188-A/B/C 1111 1111 1111 1111 MS-27-2:vp1 3 Iub_GRY913 GRY913-A/B/C 11111 11111 11111 1111 MS-24-1:vp1 3 Iub_GRY916 GRY916-A/B/C 11111 11111 11111 1111 MS-24-1:vp1 3 Iub_GRY553 GRY553-A/B/C 11111 11111 11111 1111 MS-24-1:vp1 3 Iub_GRY349 GRY349-A/B/C 1111 1111 1111 1111 MS-24-1:vp1 3 Iub_GRY363 GRY363-A/B/C 11111 11111 11111 1111 MS-24-1:vp1 3 Iub_GRY404 GRY404-A/B/C 11111 11111 11111 1111 MS-24-1:vp1 3 Iub_GRY427 GRY427-A/B/C 1111 1111 1111 1111 MS-24-1:vp1 3 Iub_GRY258 GRY258-A/B/C 1111 1111 1111 1111 MS-24-1:vp1 3 Iub_GRY272 GRY272-A/B/C 11111 11111 11111 1111 MS-24-1:vp1 3 Iub_GRY734 GRY734-A/B/C 11111 11111 11111 1111 MS-24-1:vp1 4 Iub_GRY410 GRY410-A/B/C 11111 11111 11111 1111 MS-24-1:vp1 4 Iub_GRY392 GRY392-A/B/C 1111 1111 1111 1111 ES-1-2-1-54:vp1 4 Iub_GRY877 GRY877-A/B/C 1111 1111 1111 1111 MS-24-1:vp1 4 Iub_GRY723 GRY723-A/B/C 1111 1111 1111 1111 ES-1-2-1-59:vp1 4 Iub_GRY038 GRY038-A/B/C 1111 1111 1111 1111 MS-26-1:vp1 4 Iub_GRY039 GRY039-A/B/C 1111 1111 1111 1111 ES-1-2-1-60:vp1 4 Iub_GRY267 GRY267-A/B/C 11111 11111 11111 1111 MS-26-1:vp1 4 Iub_GRY280 GRY280-A/B/C 11111 11111 11111 1111 MS-24-1:vp1 4 Iub_GRY305 GRY305-A/B/C 11111 11111 11111 1111 MS-24-1:vp1 4 Iub_GRY519 GRY519-A/B/C 11111 11111 11111 1111 ES-1-2-1-57:vp1 4 Iub_GRY059 GRY059-A/B/C 11111 11111 11111 1111 MS-24-1:vp1 4 Iub_GRY974 GRY974-A/B/C 1111 1111 1111 1111 MS-24-1:vp1 4 Iub_GRY307 GRY307-A/B/C 11111 11111 11111 1111 MS-26-1:vp1 4 Iub_GRY112 GRY112-A/B/C 11111 11111 11111 1111 ES-1-2-1-62:vp1 4 Iub_GRY327 GRY327-A/B/C 11111 11111 11111 1111 MS-26-1:vp1 4 Iub_GRY347 GRY347-A/B/C 11111 11111 11111 1111 MS-24-1:vp1 4 Iub_GRY210 GRY210-A/B/C 11111 11111 11111 1111 ES-1-2-1-61:vp1 4 Iub_GRY198 GRY198-A/B/C 11111 11111 11111 1111 ES-1-2-1-58:vp1 4 Iub_GRY908 GRY908-A/B/C 11111 11111 11111 1111 MS-24-1:vp1 4 Iub_GRY234 GRY234-A/B/C 1111 1111 1111 1111 ES-1-2-1-42:vp1 4 Iub_GRY500 GRY500-A/B/C 1111 1111 1111 1111 MS-24-1:vp1

5 Iub_GRY525 GRY525-A/B/C 1111 1111 1111 1111 ES-2-2-1-ima63:vp1 5 Iub_GRY069 GRY069-A/B/C 1111 1111 1111 1111 ES-1-26-1-ima13:vp1 5 Iub_GRY818 GRY818-A/B/C 1111 1111 1111 1111 ES-1-26-1-ima11:vp1 5 Iub_GRY200 GRY200-A/B/C 11111 11111 11111 1111 ES-2-4-1-ima43:vp1 5 Iub_GRY875 GRY875-A/B/C 1111 1111 1111 1111 ES-3-2-1-ima7:vp1 5 Iub_GRY935 GRY935-A/B/C 1111 1111 1111 1111 ES-2-2-1-ima13:vp1 5 Iub_GRY265 GRY265-A/B/C 11111 11111 11111 1111 ES-2-4-1-ima15:vp1 5 Iub_GRY281 GRY281-A/B/C 11111 11111 11111 1111 ES-3-24-1-ima51:vp1 5 Iub_GRY070 GRY070-A/B/C 11111 11111 11111 1111 ES-1-2-1-ima41:vp1 5 Iub_GRY058 GRY058-A/B/C 1111 1111 1111 1111 MS-26-1:vp1 5 Iub_GRY800 GRY800-A/B/C 11111 11111 11111 1111 ES-1-26-1-ima24:vp1 5 Iub_GRY388 GRY388-A/B/C 1111 1111 1111 1111 ES-2-2-1-ima11:vp1 5 Iub_GRY506 GRY506-A/B/C 1111 1111 1111 1111 ES-1-26-1-ima1:vp1 6 Iub_GRY412 GRY412-A/B/C 1111 1111 1111 1111 ES-2-4-1-ima3:vp1 6 Iub_GRY874 GRY874-A/B/C 1111 1111 1111 1111 ES-3-2-1-5:vp1 6 Iub_GRY015 GRY015-A/B/C 11111 11111 11111 1111 MS-26-1:vp1 6 Iub_GRY954 GRY954-A/B/C 1111 1111 1111 1111 ES-3-24-1-36:vp1 6 Iub_GRY728 GRY728-A/B/C 11111 11111 11111 1111 MS-24-1:vp1 6 Iub_GRY843 GRY843-A/B/C 11111 11111 11111 1111 ES-3-24-1-ima40:vp1 6 Iub_GRY002 GRY002-A/B/C 1111 1111 1111 1111 ES-3-24-1-ima1:vp1 6 Iub_GCOW01 GCOW01-A/B/C 11111 11111 11111 1111 ES-2-2-1-ima3:vp1 6 Iub_GCOW02 GCOW02-A/B/C 11111 11111 11111 1111 ES-2-2-1-ima6:vp1 6 Iub_GRY004 GRY004-A/B/C 1111 1111 1111 1111 MS-24-1:vp1 6 Iub_GRY927 GRY927-A/B/C 1111 1111 1111 1111 ES-2-2-1-ima9:vp1 6 Iub_GRY255 GRY255-A/B/C 11111 11111 11111 1111 MS-24-1:vp1 7 Iub_GRY965 GRY965-A/B/C 1111 1111 1111 1111 ES-2-24-1-ima3:vp1 7 Iub_GRY065 GRY065-A/B/C 11111 11111 11111 1111 ES-2-2-1-17:vp1 7 Iub_GRY830 GRY830-A/B/C 1111 1111 1111 1111 ES-3-2-1-ima43:vp1 7 Iub_GRY393 GRY393-A/B/C 11111 11111 11111 1111 ES-2-2-1-ima39:vp1 7 Iub_GRY224 GRY224-A/B/C 11111 11111 11111 1111 ES2-2-1-38:vp1 7 Iub_GRY458 GRY458-A/B/C 1111 1111 1111 1111 ES-1-2-1-ima29:vp1 7 Iub_GRY475 GRY475-A/B/C 1111 1111 1111 1111 ES-3-2-1-ima13:vp1 7 Iub_GRY300 GRY300-A/B/C 11111 11111 11111 1111 MS-26-1:vp1 7 Iub_GRY955 GRY955-A/B/C 1111 1111 1111 1111 ES-2-2-1-31:vp1 7 Iub_GRY971 GRY971-A/B/C 11111 11111 11111 1111 ES-2-2-1-ima20:vp1 7 Iub_GRY076 GRY076-A/B/C 1111 1111 1111 1111 ES-2-2-1-ima29:vp1 7 Iub_GRY997 GRY997-A/B/C 1111 1111 1111 1111 ES-3-2-1-ima19:vp1 7 Iub_GRY346 GRY346-A/B/C 1111 1111 1111 1111 ES2-2-1-ima30:vp1 7 Iub_GRY380 GRY380-A/B/C 11111 11111 11111 1111 ES-2-24-1-ima28:vp1 7 Iub_GRY401 GRY401-A/B/C 11111 11111 11111 1111 ES-2-24-1-ima15:vp1 7 Iub_GRY698 GRY698-A/B/C 1111 1111 1111 1111 ES-1-26-1-ima28:vp1 8 Iub_GRY276 GRY276-A/B/C 11111 11111 11111 1111 MS-26-1:vp1 8 Iub_GRY774 GRY774-A/B/C 11111 11111 11111 1111 MS-26-1:vp1 8 Iub_GRY567 GRY567-A/B/C 11111 11111 11111 1111 MS-26-1:vp1 8 Iub_GRY399 GRY399-A/B/C 11111 11111 11111 1111 MS-26-1:vp1 8 Iub_GRY220 GRY220-A/B/C 11111 11111 11111 1111 MS-26-1:vp1 8 Iub_GRY223 GRY223-A/B/C 11111 11111 11111 1111 MS-24-1:vp1 8 Iub_GRY225 GRY225-A/B/C 11111 11111 11111 1111 MS-26-1:vp1 8 Iub_GRY014 GRY014-A/B/C 11111 11111 11111 1111 MS-26-1:vp1 8 Iub_GRY261 GRY261-A/B/C 11111 11111 11111 1111 MS-26-1:vp1 8 Iub_GRY051 GRY051-A/B/C 11111 11111 11111 1111 MS-26-1:vp1 8 Iub_GRY053 GRY053-A/B/C 11111 11111 11111 1111 MS-26-1:vp1 8 Iub_GRY308 GRY308-A/B/C 11111 11111 11111 1111 MS-26-1:vp1 8 Iub_GRY426 GRY426-A/B/C 11111 11111 11111 1111 MS-26-1:vp1 8 Iub_GRY443 GRY443-A/B/C 11111 11111 11111 1111 MS-26-1:vp1 8 Iub_GRY522 GRY522-A/B/C 11111 11111 11111 1111 MS-26-1:vp1 9 Iub_GRY720 GRY720-A/B/C 1111 1111 1111 1111 ES-1-24-1-ima17:vp1 9 Iub_GRY531 GRY531-A/B/C 1111 1111 1111 1111 ES-1-24-1-ima36:vp1 9 Iub_GRY973 GRY973-A/B/C 11111 11111 11111 1111 ES-1-26-1-ima47:vp1 9 Iub_GRY111 GRY111-A/B/C 1111 1111 1111 1111 ES-1-26-1-ima43:vp1 9 Iub_GRY554 GRY554-A/B/C 1111 1111 1111 1111 ES-1-26-1-ima9:vp1 9 Iub_GRY345 GRY345-A/B/C 1111 1111 1111 1111 ES-1-26-1-ima34:vp1 9 Iub_GRY786 GRY786-A/B/C 1111 1111 1111 1111 ES-1-24-1-ima9:vp1 9 Iub_GRY619 GRY619-A/B/C 1111 1111 1111 1111 ES-1-24-1-ima55:vp1

9 Iub_GRY424 GRY424-A/B/C 1111 1111 1111 1111 ES-1-24-1-ima49:vp1 9 Iub_GRY194 GRY194-A/B/C 1111 1111 1111 1111 ES-1-24-1-ima43:vp1 9 Iub_GRY446 GRY446-A/B/C 11111 11111 11111 1111 ES-1-26-1-ima30:vp1 9 Iub_GRY909 GRY909-A/B/C 1111 1111 1111 1111 ES-1-26-1-ima36:vp1 9 Iub_GRY009 GRY009-A/B/C 1111 1111 1111 1111 ES-1-24-1-ima59:vp1 9 Iub_GRY679 GRY679-A/B/C 1111 1111 1111 1111 ES-1-24-1-ima57:vp1 9 Iub_GRY717 GRY717-A/B/C 1111 1111 1111 1111 ES-1-26-1-ima59:vp1 10 Iub_GRY813 GRY813-A/B/C 11111 11111 11111 1111 ES-1-26-1-ima49:vp1 10 Iub_GRY203 GRY203-A/B/C 1111 1111 1111 1111 ES-2-2-1-ima32:vp1 10 Iub_GRY205 GRY205-A/B/C 1111 1111 1111 1111 ES-1-26-1-ima45:vp1 10 Iub_GRY897 GRY897-A/B/C 11111 11111 11111 1111 ES-2-2-1-ima55:vp1 10 Iub_GRY742 GRY742-A/B/C 1111 1111 1111 1111 ES2-2-1-ima46:vp1 10 Iub_GRY342 GRY342-A/B/C 11111 11111 11111 1111 ES-1-24-1-ima38:vp1 10 Iub_GRY597 GRY597-A/B/C 11111 11111 11111 1111 ES-2-2-1-ima57:vp1 10 Iub_GRY657 GRY657-A/B/C 11111 11111 11111 1111 ES-3-24-1-ima55:vp1 11 Iub_GRY310 GRY310-A/B/C 11111 11111 11111 1111 ES2-2-1-ima41:vp1 11 Iub_GRY356 GRY356-A/B/C 11111 11111 11111 1111 ES-2-4-1-ima26:vp1 11 Iub_GRY832 GRY832-A/B/C 1111 1111 1111 1111 ES-2-4-1-ima17:vp1 11 Iub_GRY376 GRY376-A/B/C 1111 1111 1111 1111 ES-2-2-1-ima34:vp1 11 Iub_GRY663 GRY663-A/B/C 11111 11111 11111 1111 ES-2-24-1-25:vp1 11 Iub_GRY011 GRY011-A/B/C 11111 11111 11111 1111 ES-2-2-1-42:vp1 11 Iub_GRY018 GRY018-A/B/C 1111 1111 1111 1111 ES-2-24-1-ima32:vp1 11 Iub_GRY722 GRY722-A/B/C 1111 1111 1111 1111 ES-2-4-1-ima5:vp1 11 Iub_GRY535 GRY535-A/B/C 1111 1111 1111 1111 ES-2-4-1-ima19:vp1 11 Iub_GRY440 GRY440-A/B/C 1111 1111 1111 1111 ES-2-4-1-ima22:vp1 11 Iub_GRY868 GRY868-A/B/C 1111 1111 1111 1111 ES-2-24-1-ima53:vp1 11 Iub_GRY901 GRY901-A/B/C 1111 1111 1111 1111 ES-2-24-1-38:vp1 11 Iub_GRY444 GRY444-A/B/C 11111 11111 11111 1111 ES-2-4-1-ima34:vp1 11 Iub_GRY025 GRY025-A/B/C 11111 11111 11111 1111 ES-2-24-1-ima26:vp1 11 Iub_GRY042 GRY042-A/B/C 1111 1111 1111 1111 ES-2-4-1-ima1:vp1 11 Iub_GRY274 GRY274-A/B/C 11111 11111 11111 1111 ES-2-2-1-ima40:vp1 30 Iub_GRY293 GRY293-A/B/C 11111 11111 11111 1111 MS-26-1:vp1 30 Iub_GRY294 GRY294-A/B/C 11111 11111 11111 1111 MS-26-1:vp1 30 Iub_GRY102 GRY102-A/B/C 11111 11111 11111 1111 ES-1-26-1-ima51:vp1 30 Iub_GRY088 GRY088-A/B/C 11111 11111 11111 1111 ES-3-2-1-34:vp1 30 Iub_GRY817 GRY817-A/B/C 1111 1111 1111 1111 ES-3-24-1-61:vp1 30 Iub_GRY839 GRY839-A/B/C 11111 11111 11111 1111 ES-3-24-1-ima47:vp1 30 Iub_GRY379 GRY379-A/B/C 1111 1111 1111 1111 ES-1-26-1-ima22:vp1 30 Iub_GRY208 GRY208-A/B/C 1111 1111 1111 1111 ES-3-2-1-ima32:vp1 30 Iub_GRY912 GRY912-A/B/C 11111 11111 11111 1111 ES-2-4-1-ima30:vp1 30 Iub_GRY895 GRY895-A/B/C 1111 1111 1111 1111 ES-1-2-1-ima28:vp1 30 Iub_GRY721 GRY721-A/B/C 1111 1111 1111 1111 ES-1-24-1-5:vp1 30 Iub_GRY936 GRY936-A/B/C 1111 1111 1111 1111 ES-2-4-1-11:vp1 30 Iub_GRY284 GRY284-A/B/C 11111 11111 11111 1111 ES-2-2-1-ima2:vp1 30 Iub_GRY996 GRY996-A/B/C 11111 11111 11111 1111 ES-3-2-1-ima55:vp1 30 Iub_GRY860 GRY860-A/B/C 11111 11111 11111 1111 ES-2-24-1-ima34:vp1 30 Iub_GRY670 GRY670-A/B/C 11111 11111 11111 1111 ES-2-4-1-28:vp1 30 Iub_GCOW05 GCOW05-A/B/C 11111 11111 11111 1111 ES-3-24-1-ima24:vp1 30 Iub_GRY922 GRY922-A/B/C 1111 1111 1111 1111 ES-1-26-1-26:vp1 30 Iub_GRY926 GRY926-A/B/C 11111 11111 11111 1111 ES-2-4-1-ima9:vp1 30 Iub_GRY239 GRY239-A/B/C 1111 1111 1111 1111 ES2-2-1-ima36:vp1 30 Iub_GRY940 GRY940-A/B/C 1111 1111 1111 1111 ES-3-2-1-ima17:vp1 30 Iub_GRY943 GRY943-A/B/C 11111 11111 11111 1111 ES-2-4-1-ima38:vp1 31 Iub_GRY298 GRY298-A/B/C 11111 11111 11111 1111 MS-26-1:vp1 31 Iub_GRY370 GRY370-A/B/C 1111 1111 1111 1111 ES-2-2-1-33:vp1 31 Iub_GRY202 GRY202-A/B/C 1111 1111 1111 1111 ES-3-2-1-ima9:vp1 31 Iub_GRY209 GRY209-A/B/C 11111 11111 11111 1111 ES-3-2-1-ima49:vp1 31 Iub_GRI879 GRI879-A/B/C 11111 11111 11111 1111 ES-3-24-1-ima9:vp1 31 Iub_GRY050 GRY050-A/B/C 1111 1111 1111 1111 ES-2-24-1-ima47:vp1 31 Iub_GRY099 GRY099-A/B/C 1111 1111 1111 1111 ES-3-2-1-ima30:vp1 31 Iub_GRY825 GRY825-A/B/C 1111 1111 1111 1111 ES-3-2-1-ima36:vp1 31 Iub_GRY366 GRY366-A/B/C 1111 1111 1111 1111 ES-3-24-1-ima30:vp1 31 Iub_GRY889 GRY889-A/B/C 11111 11111 11111 1111 ES-2-4-1-ima36:vp1 31 Iub_GRY236 GRY236-A/B/C 11111 11111 11111 1111 ES-1-2-1-ima43:vp1

31 Iub_GRY027 GRY027-A/B/C 1111 1111 1111 1111 ES-3-2-1-ima24:vp1 32 Iub_GRY107 GRY107-A/B/C 11111 11111 11111 1111 ES-2-24-1-ima30:vp1 32 Iub_GRY375 GRY375-A/B/C 11111 11111 11111 1111 ES-3-24-1-ima32:vp1 32 Iub_GRY396 GRY396-A/B/C 11111 11111 11111 1111 ES-2-4-1-ima45:vp1 32 Iub_GRY934 GRY934-A/B/C 1111 1111 1111 1111 ES-1-24-1-ima15:vp1 32 Iub_GRY513 GRY513-A/B/C 11111 11111 11111 1111 ES-2-24-1-ima20:vp1 32 Iub_GRY515 GRY515-A/B/C 1111 1111 1111 1111 ES-1-24-1-ima32:vp1 32 Iub_GRY959 GRY959-A/B/C 11111 11111 11111 1111 ES-1-2-1-4:vp1 32 Iub_GRY325 GRY325-A/B/C 11111 11111 11111 1111 ES-1-24-1-ima19:vp1 32 Iub_GRY826 GRY826-A/B/C 1111 1111 1111 1111 ES-1-24-1-ima7:vp1 32 Iub_GRY865 GRY865-A/B/C 11111 11111 11111 1111 ES-2-24-1-ima51:vp1 32 Iub_GRI002 GRI002-A/B/C 11111 11111 11111 1111 ES-2-2-1-ima1:vp1 32 Iub_GRY005 GRY005-A/B/C 1111 1111 1111 1111 ES-1-2-1-ima2:vp1 32 Iub_GRY237 GRY237-A/B/C 11111 11111 11111 1111 ES-3-2-1-ima40:vp1 32 Iub_GRY250 GRY250-A/B/C 11111 11111 11111 1111 ES-2-24-1-ima17:vp1 32 Iub_GRY520 GRY520-A/B/C 11111 11111 11111 1111 ES-3-2-1-ima51:vp1 32 Iub_GRY735 GRY735-A/B/C 11111 11111 11111 1111 ES-2-4-1-ima32:vp1 33 Iub_GRY541 GRY541-A/B/C 1111 1111 1111 1111 ES-3-24-1-ima38:vp1 33 Iub_GRY976 GRY976-A/B/C 11111 11111 11111 1111 ES-3-24-1-ima43:vp1 33 Iub_GRY804 GRY804-A/B/C 11111 11111 11111 1111 ES-3-2-1-ima28:vp1 33 Iub_GRY344 GRY344-A/B/C 11111 11111 11111 1111 ES-3-24-1-ima45:vp1 33 Iub_GRY806 GRY806-A/B/C 1111 1111 1111 1111 ES-3-2-1-ima57:vp1 33 Iub_GRY807 GRY807-A/B/C 1111 1111 1111 1111 ES-3-2-1-ima59:vp1 33 Iub_GRY408 GRY408-A/B/C 11111 11111 11111 1111 ES-3-2-1-ima3:vp1 33 Iub_GRY389 GRY389-A/B/C 1111 1111 1111 1111 ES-3-2-1-ima47:vp1 33 Iub_GRY675 GRY675-A/B/C 1111 1111 1111 1111 ES-3-2-1-ima38:vp1 33 Iub_GRY465 GRY465-A/B/C 1111 1111 1111 1111 ES-3-2-1-ima26:vp1 33 Iub_GRY947 GRY947-A/B/C 1111 1111 1111 1111 ES-3-2-1-ima61:vp1 34 Iub_GRY850 GRY850-A/B/C 11111 11111 11111 1111 ES-3-24-1-ima49:vp1 34 Iub_GRY950 GRY950-A/B/C 1111 1111 1111 1111 ES-1-24-1-ima40:vp1 41 Iub_GRI984 GRI984-A/B/C 11111 11111 11111 1111 ES-3-24-1-23:vp1 ----------------------------------------------------------------------------------------------- Following 65 sites are totally or partially unavailable: -----------------------------------------------------------------------------------------------MOD IUBLINK CELLNAMES CELL1 CELL2 CELL3 CD12 ATMPORTS ----------------------------------------------------------------------------------------------- 1 Iub_GRY560 GRY560-A/B/C 0000 0000 0000 1011 MS-26-1:vp1 2 Iub_GRY851 GRY851-A/B/C 1111L 1111L 1111L 1111 ES-2-24-1-ima43:vp1 2 Iub_GRY647 GRY647-A/B/C 1111L 1111L 1111L 1111 ES-2-2-1-19:vp1 2 Iub_GRY849 GRY849-A/B/C 1111L 1111L 1111L 1111 ES-2-2-1-ima21:vp1 3 Iub_GRY066 GRY066-A/B/C 1000 1000 1000 1111 ES-1-4-1-17:vp1 3 Iub_GRY770 GRY770-A/B/C 00000 00000 00000 0011 ES-1-4-1-ima19:vp1 3 Iub_GRY798 GRY798-A/B/C 1000 1000 1000 1111 ES-1-4-1-47:vp1 3 Iub_GRY852 GRY852-A/B/C 1111L 1111L 1111L 1111 ES-1-2-1-ima46:vp1 3 Iub_GRY853 GRY853-A/B/C 10001 10001 10001 1111 ES-1-4-1-45:vp1 3 Iub_GRY248 GRY248-A/B/C 1000 1000 1000 1111 ES-1-4-1-7:vp1 3 Iub_GRY846 GRY846-A/B/C 1000 1000 1000 1111 ES-1-4-1-23:vp1 3 Iub_GRY442 GRY442-A/B/C 1000 1000 1000 1111 ES-1-4-1-57:vp1 3 Iub_GRY022 GRY022-A/B/C 1000 1000 1000 1111 ES-1-4-1-38:vp1 4 Iub_GRY321 GRY321-A/B/C 1111L 1111L 1111L 1111 ES-1-26-1-ima3:vp1 4 Iub_GRY502 GRY502-A/B/C 00000 00000 00000 0011 ES-1-4-1-ima48:vp1 5 Iub_GRY527 GRY527-A/B/C 1111L 1111L 1111L 1111 ES-2-24-1-ima11:vp1 5 Iub_GRI836 GRI836-A/B/C 00000 00000 00000 0011 ES-1-4-1-ima14:vp1 5 Iub_GRY766 GRY766-A/B/C 1000 1000 1000 1111 ES-1-4-1-29:vp1 5 Iub_GRY998 GRY998-A/B/C 1111L 1111L 1111L 1111 ES-3-2-1-ima11:vp1 5 Iub_GRY880 GRY880-A/B/C 1111L 1111L 1111L 1111 ES-3-2-1-ima1:vp1 5 Iub_GRY021 GRY021-A/B/C 00000 00000 00000 0011 ES-1-4-1-ima12:vp1 5 Iub_GRY271 GRY271-A/B/C 00000 00000 00000 0011 ES-1-4-1-ima24:vp1 7 Iub_GRY915 GRY915-A/B/C 1111 1111L 1111L 1111 ES-2-24-1-ima7:vp1 7 Iub_GRY470 GRY470-A/B/C 1111L 1111L 1111L 1111 ES-3-2-1-ima15:vp1 7 Iub_GRY533 GRY533-A/B/C 1111L 1111L 1111L 1111 ES-1-24-1-ima3:vp1 7 Iub_GRY040 GRY040-A/B/C 1111L 1111L 1111L 1111 ES-3-2-1-ima22:vp1 8 Iub_GRY530 GRY530-A/B/C 1111L 1111L 1111L 1111 MS-27-2:vp1

9 Iub_GRY116 GRY116-A/B/C 00000 00000 00000 0011 ES-1-4-1-ima2:vp1 9 Iub_GRY575 GRY575-A/B/C 0000 0000 0000 0011 ES-1-4-1-ima9:vp1 9 Iub_GRY441 GRY441-A/B/C 1111L 1111L 1111L 1111 ES-1-26-1-ima38:vp1 10 Iub_GRY844 GRY844-A/B/C 00000 00000 00000 0011 ES-1-4-1-ima21:vp1 10 Iub_GRY907 GRY907-A/B/C 00000 00000 00000 0011 ES-1-4-1-ima31:vp1 11 Iub_GRY977 GRY977-A/B/C 1111L 1111L 1111L 1111 ES-2-24-1-ima40:vp1 12 Iub_GCW617 GCW617-A/B/C 11111 11111 LLLLL 1111 ES-2-24-1-ima22:vp1 30 Iub_GRY279 GRY279-A/B/C 1000 1000 1000 1111 ES-1-4-1-53:vp1 30 Iub_GRY295 GRY295-A/B/C 1000 1000 1000 1111 ES-1-4-1-34:vp1 30 Iub_GRY087 GRY087-A/B/C 10001 10001 10001 1111 ES-1-4-1-43:vp1 30 Iub_GRY834 GRY834-A/B/C 1111L 1111L 1111L 1111 ES-2-2-1-ima16:vp1 30 Iub_GRY411 GRY411-A/B/C 1111L 1111L 1111L 1111 ES-2-4-1-ima24:vp1 30 Iub_GRY341 GRY341-A/B/C 1111L 1111L 1111L 1111 ES-1-24-1-ima1:vp1 30 Iub_GRY119 GRY119-A/B/C 1000 1000 1000 1111 ES-1-4-1-51:vp1 30 Iub_GRY787 GRY787-A/B/C 1111L 1111L 1111L 1111 ES-2-24-1-ima36:vp1 30 Iub_GRY820 GRY820-A/B/C 1111L 1111L 1111L 1111 ES-1-26-1-ima7:vp1 30 Iub_GRY001 GRY001-A/B/C 1111L 1111L 1111L 1111 ES-2-24-1-ima57:vp1 30 Iub_GRY230 GRY230-A/B/C 10001 10001 10001 1111 ES-1-4-1-55:vp1 30 Iub_GCOW04 GCOW04-A/B/C LLLLL LLLLL LLLLL LLLL ES-2-2-1-ima48:vp1 30 Iub_GRY024 GRY024-A/B/C 10001 10001 10001 1111 ES-1-4-1-40:vp1 30 Iub_GRY944 GRY944-A/B/C 1111L 1111L 1111L 1111 ES-1-24-1-ima13:vp1 30 Iub_GRY259 GRY259-A/B/C 1111L 1111L 1111L 1111 ES-2-2-1-28:vp1 31 Iub_GRY964 GRY964-A/B/C 1111L 1111L 1111L 1111 ES-3-2-1-ima45:vp1 31 Iub_GRY350 GRY350-A/B/C 1111L 1111L 1111L 1111 ES-2-24-1-ima55:vp1 32 Iub_GRY204 GRY204-A/B/C 1111L 1111L 1111L 1111 ES-1-24-1-ima26:vp1 32 Iub_GRY896 GRY896-A/B/C 10001 10001 10001 1111 ES-1-4-1-3:vp1 32 Iub_GRY472 GRY472-A/B/C 1111L 1111L 1111L 1111 ES-1-24-1-ima22:vp1 32 Iub_GRY957 GRY957-A/B/C 1111L 1111L 1111L 1111 ES-1-24-1-ima30:vp1 32 Iub_GRY744 GRY744-A/B/C 00000 00000 00000 0011 ES-1-4-1-ima11:vp1 32 Iub_GRY286 GRY286-A/B/C 1111L 1111L 1111L 1111 ES-2-24-1-ima45:vp1 32 Iub_GRY808 GRY808-A/B/C 1111L 1111L 1111L 1111 ES-1-24-1-ima34:vp1 34 Iub_GRY911 GRY911-A/B/C 1111L 1111L 1111L 1111 ES-3-2-1-ima53:vp1 40 Iub_GRY064 GRY064-A/B/C 10001 10001 10001 1111 ES-1-4-1-61:vp1 40 Iub_GCW616 GCW616-A/B/C L0000 L0000 L0000 0011 ES-1-4-1-ima39:vp1 50 Iub_GRY545 GRY545-A/B/C 10001 10001 10001 1111 ES-1-4-1-32:vp1 50 Iub_GRY332 GRY332-A/B/C 1000 1000 1000 1111 ES-1-4-1-59:vp1 50 Iub_GRY249 GRY249-A/B/C 1000 1000 1000 1111 ES-1-4-1-36:vp1 50 Iub_GRI880 GRI880-A/B/C 10001 10001 10001 1111 ES-1-4-1-52:vp1 ----------------------------------------------------------------------------------------------- Cell availability: 687 of 879 cells are up (78.2 %) Site availability: 228 of 293 sites are fully operational (77.8 %) Unlocked Cell availability: 687 of 872 unlocked cells are up (78.8 %) /* All sites recover after 2nd restart, GRY502 still down, but this site needs to be deleted & recreated */ 3RR01> lst b1013 070524-06:09:19 172.24.12.207 7.0 RESTRICTED RNC_NODE_MODEL_F_5_2 stopfile=/tmp/19957 =================================================================================== Proxy Adm State Op. State MO =================================================================================== 10683 1 (ENABLED) TransportNetwork=1,AtmCrossConnection=b1013ia 10684 1 (ENABLED) TransportNetwork=1,AtmCrossConnection=b1013ib 11492 1 (UNLOCKED) 0 (DISABLED) TransportNetwork=1,Aal2PathVccTp=b1013a1 11493 1 (UNLOCKED) 0 (DISABLED) TransportNetwork=1,Aal2PathVccTp=b1013a2 13443 0 (DISABLED) TransportNetwork=1,Aal5TpVccTp=b1013qa 13444 0 (DISABLED) TransportNetwork=1,Aal5TpVccTp=b1013qb 13445 0 (DISABLED) TransportNetwork=1,Aal5TpVccTp=b1013ca 13446 0 (DISABLED) TransportNetwork=1,Aal5TpVccTp=b1013cb 13447 0 (DISABLED) TransportNetwork=1,Aal5TpVccTp=b1013da 13448 0 (DISABLED) TransportNetwork=1,Aal5TpVccTp=b1013db 14165 0 (DISABLED) TransportNetwork=1,Aal0TpVccTp=b1013sa1

14166 0 (DISABLED) TransportNetwork=1,Aal0TpVccTp=b1013sb1 14416 0 (DISABLED) TransportNetwork=1,Aal2Sp=1,Aal2Ap=b1013 16091 0 (DISABLED) TransportNetwork=1,UniSaalTp=b1013qa 16092 0 (DISABLED) TransportNetwork=1,UniSaalTp=b1013qb 16093 0 (DISABLED) TransportNetwork=1,UniSaalTp=b1013ca 16094 0 (DISABLED) TransportNetwork=1,UniSaalTp=b1013cb 16095 0 (DISABLED) TransportNetwork=1,UniSaalTp=b1013da 16096 0 (DISABLED) TransportNetwork=1,UniSaalTp=b1013db =================================================================================== Total: 19 MOs 3RR01> lst gry502 070524-06:09:31 172.24.12.207 7.0 RESTRICTED RNC_NODE_MODEL_F_5_2 stopfile=/tmp/19957 =================================================================================== Proxy Adm State Op. State MO =================================================================================== 2049 1 (UNLOCKED) 0 (DISABLED) RncFunction=1,UtranCell=GRY502A,Rach=1 2050 1 (UNLOCKED) 0 (DISABLED) RncFunction=1,UtranCell=GRY502B,Rach=1 2051 1 (UNLOCKED) 0 (DISABLED) RncFunction=1,UtranCell=GRY502C,Rach=1 4284 1 (UNLOCKED) 0 (DISABLED) RncFunction=1,UtranCell=GRY502A,Hsdsch=1 4285 1 (UNLOCKED) 0 (DISABLED) RncFunction=1,UtranCell=GRY502B,Hsdsch=1 4286 1 (UNLOCKED) 0 (DISABLED) RncFunction=1,UtranCell=GRY502C,Hsdsch=1 5163 1 (UNLOCKED) 0 (DISABLED) RncFunction=1,UtranCell=GRY502A,Pch=1 5164 1 (UNLOCKED) 0 (DISABLED) RncFunction=1,UtranCell=GRY502B,Pch=1 5165 1 (UNLOCKED) 0 (DISABLED) RncFunction=1,UtranCell=GRY502C,Pch=1 6042 1 (UNLOCKED) 0 (DISABLED) RncFunction=1,UtranCell=GRY502A,Fach=1 6043 1 (UNLOCKED) 0 (DISABLED) RncFunction=1,UtranCell=GRY502B,Fach=1 6044 1 (UNLOCKED) 0 (DISABLED) RncFunction=1,UtranCell=GRY502C,Fach=1 6337 1 (UNLOCKED) 0 (DISABLED) RncFunction=1,IubLink=Iub_GRY502,NbapCommon=1 8598 1 (UNLOCKED) 1 (ENABLED) RncFunction=1,IubLink=Iub_GRY502,NodeSynchTp=1 8599 1 (UNLOCKED) 1 (ENABLED) RncFunction=1,IubLink=Iub_GRY502,NodeSynchTp=2 8892 1 (UNLOCKED) 0 (DISABLED) RncFunction=1,IubLink=Iub_GRY502,NbapDedicated=1 9185 1 (ENABLED) RncFunction=1,IubLink=Iub_GRY502 10062 1 (UNLOCKED) 0 (DISABLED) RncFunction=1,UtranCell=GRY502A 10063 1 (UNLOCKED) 0 (DISABLED) RncFunction=1,UtranCell=GRY502B 10064 1 (UNLOCKED) 0 (DISABLED) RncFunction=1,UtranCell=GRY502C 3RR01> lst vc12ttp=26|vc12ttp=24 070524-06:18:52 172.24.12.207 7.0 RESTRICTED RNC_NODE_MODEL_F_5_2 stopfile=/tmp/19957 =================================================================================== Proxy Adm State Op. State MO =================================================================================== 16541 1 (UNLOCKED) 1 (ENABLED) Equipment=1,Subrack=ES-1,Slot=4,PlugInUnit=1,Etmc41=1,Os155SpiTtp=pp1,Vc4Ttp=1,Vc12Ttp=26 16542 1 (ENABLED) Equipment=1,Subrack=ES-1,Slot=4,PlugInUnit=1,Etmc41=1,Os155SpiTtp=pp1,Vc4Ttp=1,Vc12Ttp=26,E1Ttp=1 16545 1 (UNLOCKED) 1 (ENABLED) Equipment=1,Subrack=ES-1,Slot=4,PlugInUnit=1,Etmc41=1,Os155SpiTtp=pp1,Vc4Ttp=1,Vc12Ttp=24 16546 1 (ENABLED) Equipment=1,Subrack=ES-1,Slot=4,PlugInUnit=1,Etmc41=1,Os155SpiTtp=pp1,Vc4Ttp=1,Vc12Ttp=24,E1Ttp=1 =================================================================================== Total: 4 MOs 3RR01> lst vc12ttp=14|vc12ttp=15|vc12ttp=16 070524-06:21:27 172.24.12.207 7.0 RESTRICTED RNC_NODE_MODEL_F_5_2 stopfile=/tmp/19957 =================================================================================== Proxy Adm State Op. State MO ===================================================================================

16561 1 (UNLOCKED) 0 (DISABLED) Equipment=1,Subrack=ES-1,Slot=4,PlugInUnit=1,Etmc41=1,Os155SpiTtp=pp1,Vc4Ttp=1,Vc12Ttp=16 16562 0 (DISABLED) Equipment=1,Subrack=ES-1,Slot=4,PlugInUnit=1,Etmc41=1,Os155SpiTtp=pp1,Vc4Ttp=1,Vc12Ttp=16,E1Ttp=1 16563 1 (UNLOCKED) 0 (DISABLED) Equipment=1,Subrack=ES-1,Slot=4,PlugInUnit=1,Etmc41=1,Os155SpiTtp=pp1,Vc4Ttp=1,Vc12Ttp=15 16564 0 (DISABLED) Equipment=1,Subrack=ES-1,Slot=4,PlugInUnit=1,Etmc41=1,Os155SpiTtp=pp1,Vc4Ttp=1,Vc12Ttp=15,E1Ttp=1 16565 1 (UNLOCKED) 0 (DISABLED) Equipment=1,Subrack=ES-1,Slot=4,PlugInUnit=1,Etmc41=1,Os155SpiTtp=pp1,Vc4Ttp=1,Vc12Ttp=14 16566 0 (DISABLED) Equipment=1,Subrack=ES-1,Slot=4,PlugInUnit=1,Etmc41=1,Os155SpiTtp=pp1,Vc4Ttp=1,Vc12Ttp=14,E1Ttp=1 =================================================================================== Total: 6 MOs /* After 2nd ETM board restart, all those sites recovered. Now the engineer are going to delete & recreate */ /* Deletion In-progress */ 3RR01> lst b1013 070524-06:55:41 172.24.12.207 7.0 RESTRICTED RNC_NODE_MODEL_F_5_2 stopfile=/tmp/19957 =================================================================================== Proxy Adm State Op. State MO =================================================================================== 10683 !!!! Processing failure :se.ericsson.cello.moframework.MoNotFoundException TAG :"MoNotFound" VARIABLES :"$dName" = "ManagedElement=1,TransportNetwork=1,AtmCrossConnection=b1013ia" TransportNetwork=1,AtmCrossConnection=b1013ia 10684 !!!! Processing failure :se.ericsson.cello.moframework.MoNotFoundException TAG :"MoNotFound" VARIABLES :"$dName" = "ManagedElement=1,TransportNetwork=1,AtmCrossConnection=b1013ia" TransportNetwork=1,AtmCrossConnection=b1013ib 11492 !!!! Processing failure :se.ericsson.cello.moframework.MoNotFoundException TAG :"MoNotFound" VARIABLES :"$dName" = "ManagedElement=1,TransportNetwork=1,AtmCrossConnection=b1013ia" !!!! Processing failure :se.ericsson.cello.moframework.MoNotFoundException TAG :"MoNotFound" VARIABLES :"$dName" = "ManagedElement=1,TransportNetwork=1,AtmCrossConnection=b1013ia" TransportNetwork=1,Aal2PathVccTp=b1013a1 11493 !!!! Processing failure :se.ericsson.cello.moframework.MoNotFoundException TAG :"MoNotFound" VARIABLES :"$dName" = "ManagedElement=1,TransportNetwork=1,AtmCrossConnection=b1013ia" !!!! Processing failure :se.ericsson.cello.moframework.MoNotFoundException TAG :"MoNotFound" VARIABLES :"$dName" = "ManagedElement=1,TransportNetwork=1,AtmCrossConnection=b1013ia" TransportNetwork=1,Aal2PathVccTp=b1013a2 13443 !!!! Processing failure :se.ericsson.cello.moframework.MoNotFoundException TAG :"MoNotFound" VARIABLES :"$dName" = "ManagedElement=1,TransportNetwork=1,AtmCrossConnection=b1013ia" TransportNetwork=1,Aal5TpVccTp=b1013qa 13444 !!!! Processing failure :se.ericsson.cello.moframework.MoNotFoundException TAG :"MoNotFound" VARIABLES :"$dName" = "ManagedElement=1,TransportNetwork=1,AtmCrossConnection=b1013ia" TransportNetwork=1,Aal5TpVccTp=b1013qb 13445 !!!! Processing failure :se.ericsson.cello.moframework.MoNotFoundException TAG :"MoNotFound" VARIABLES :"$dName" = "ManagedElement=1,TransportNetwork=1,AtmCrossConnection=b1013ia" TransportNetwork=1,Aal5TpVccTp=b1013ca 13446 !!!! Processing failure :se.ericsson.cello.moframework.MoNotFoundException TAG :"MoNotFound" VARIABLES

:"$dName" = "ManagedElement=1,TransportNetwork=1,AtmCrossConnection=b1013ia" TransportNetwork=1,Aal5TpVccTp=b1013cb 13447 !!!! Processing failure :se.ericsson.cello.moframework.MoNotFoundException TAG :"MoNotFound" VARIABLES :"$dName" = "ManagedElement=1,TransportNetwork=1,AtmCrossConnection=b1013ia" TransportNetwork=1,Aal5TpVccTp=b1013da 13448 !!!! Processing failure :se.ericsson.cello.moframework.MoNotFoundException TAG :"MoNotFound" VARIABLES :"$dName" = "ManagedElement=1,TransportNetwork=1,AtmCrossConnection=b1013ia" TransportNetwork=1,Aal5TpVccTp=b1013db 14165 !!!! Processing failure :se.ericsson.cello.moframework.MoNotFoundException TAG :"MoNotFound" VARIABLES :"$dName" = "ManagedElement=1,TransportNetwork=1,AtmCrossConnection=b1013ia" TransportNetwork=1,Aal0TpVccTp=b1013sa1 14166 !!!! Processing failure :se.ericsson.cello.moframework.MoNotFoundException TAG :"MoNotFound" VARIABLES :"$dName" = "ManagedElement=1,TransportNetwork=1,AtmCrossConnection=b1013ia" TransportNetwork=1,Aal0TpVccTp=b1013sb1 14416 !!!! Processing failure :se.ericsson.cello.moframework.MoNotFoundException TAG :"MoNotFound" VARIABLES :"$dName" = "ManagedElement=1,TransportNetwork=1,AtmCrossConnection=b1013ia" TransportNetwork=1,Aal2Sp=1,Aal2Ap=b1013 16091 !!!! Processing failure :se.ericsson.cello.moframework.MoNotFoundException TAG :"MoNotFound" VARIABLES :"$dName" = "ManagedElement=1,TransportNetwork=1,AtmCrossConnection=b1013ia" TransportNetwork=1,UniSaalTp=b1013qa 16092 !!!! Processing failure :se.ericsson.cello.moframework.MoNotFoundException TAG :"MoNotFound" VARIABLES :"$dName" = "ManagedElement=1,TransportNetwork=1,AtmCrossConnection=b1013ia" TransportNetwork=1,UniSaalTp=b1013qb 16093 !!!! Processing failure :se.ericsson.cello.moframework.MoNotFoundException TAG :"MoNotFound" VARIABLES :"$dName" = "ManagedElement=1,TransportNetwork=1,AtmCrossConnection=b1013ia" TransportNetwork=1,UniSaalTp=b1013ca 16094 !!!! Processing failure :se.ericsson.cello.moframework.MoNotFoundException TAG :"MoNotFound" VARIABLES :"$dName" = "ManagedElement=1,TransportNetwork=1,AtmCrossConnection=b1013ia" TransportNetwork=1,UniSaalTp=b1013cb 16095 !!!! Processing failure :se.ericsson.cello.moframework.MoNotFoundException TAG :"MoNotFound" VARIABLES :"$dName" = "ManagedElement=1,TransportNetwork=1,AtmCrossConnection=b1013ia" TransportNetwork=1,UniSaalTp=b1013da 16096 !!!! Processing failure :se.ericsson.cello.moframework.MoNotFoundException TAG :"MoNotFound" VARIABLES :"$dName" = "ManagedElement=1,TransportNetwork=1,AtmCrossConnection=b1013ia" TransportNetwork=1,UniSaalTp=b1013db =================================================================================== Total: 19 MOs 3RR01> lst gry502 070524-06:56:40 172.24.12.207 7.0 RESTRICTED RNC_NODE_MODEL_F_5_2 stopfile=/tmp/19957 =================================================================================== Proxy Adm State Op. State MO =================================================================================== 2049 !!!! Processing failure :se.ericsson.cello.moframework.MoNotFoundException TAG :"MoNotFound" VARIABLES :"$dName" = "ManagedElement=1,RncFunction=1,UtranCell=GRY502A,Rach=1" !!!! Processing failure :se.ericsson.cello.moframework.MoNotFoundException TAG :"MoNotFound" VARIABLES :"$dName" = "ManagedElement=1,RncFunction=1,UtranCell=GRY502A,Rach=1" RncFunction=1,UtranCell=GRY502A,Rach=1 2050 !!!! Processing failure :se.ericsson.cello.moframework.MoNotFoundException TAG :"MoNotFound" VARIABLES :"$dName" =

"ManagedElement=1,RncFunction=1,UtranCell=GRY502A,Rach=1" !!!! Processing failure :se.ericsson.cello.moframework.MoNotFoundException TAG :"MoNotFound" VARIABLES :"$dName" = "ManagedElement=1,RncFunction=1,UtranCell=GRY502A,Rach=1" RncFunction=1,UtranCell=GRY502B,Rach=1 2051 !!!! Processing failure :se.ericsson.cello.moframework.MoNotFoundException TAG :"MoNotFound" VARIABLES :"$dName" = "ManagedElement=1,RncFunction=1,UtranCell=GRY502A,Rach=1" !!!! Processing failure :se.ericsson.cello.moframework.MoNotFoundException TAG :"MoNotFound" VARIABLES :"$dName" = "ManagedElement=1,RncFunction=1,UtranCell=GRY502A,Rach=1" RncFunction=1,UtranCell=GRY502C,Rach=1 4284 !!!! Processing failure :se.ericsson.cello.moframework.MoNotFoundException TAG :"MoNotFound" VARIABLES :"$dName" = "ManagedElement=1,RncFunction=1,UtranCell=GRY502A,Rach=1" !!!! Processing failure :se.ericsson.cello.moframework.MoNotFoundException TAG :"MoNotFound" VARIABLES :"$dName" = "ManagedElement=1,RncFunction=1,UtranCell=GRY502A,Rach=1" RncFunction=1,UtranCell=GRY502A,Hsdsch=1 4285 !!!! Processing failure :se.ericsson.cello.moframework.MoNotFoundException TAG :"MoNotFound" VARIABLES :"$dName" = "ManagedElement=1,RncFunction=1,UtranCell=GRY502A,Rach=1" !!!! Processing failure :se.ericsson.cello.moframework.MoNotFoundException TAG :"MoNotFound" VARIABLES :"$dName" = "ManagedElement=1,RncFunction=1,UtranCell=GRY502A,Rach=1" RncFunction=1,UtranCell=GRY502B,Hsdsch=1 4286 !!!! Processing failure :se.ericsson.cello.moframework.MoNotFoundException TAG :"MoNotFound" VARIABLES :"$dName" = "ManagedElement=1,RncFunction=1,UtranCell=GRY502A,Rach=1" !!!! Processing failure :se.ericsson.cello.moframework.MoNotFoundException TAG :"MoNotFound" VARIABLES :"$dName" = "ManagedElement=1,RncFunction=1,UtranCell=GRY502A,Rach=1" RncFunction=1,UtranCell=GRY502C,Hsdsch=1 5163 !!!! Processing failure :se.ericsson.cello.moframework.MoNotFoundException TAG :"MoNotFound" VARIABLES :"$dName" = "ManagedElement=1,RncFunction=1,UtranCell=GRY502A,Rach=1" !!!! Processing failure :se.ericsson.cello.moframework.MoNotFoundException TAG :"MoNotFound" VARIABLES :"$dName" = "ManagedElement=1,RncFunction=1,UtranCell=GRY502A,Rach=1" RncFunction=1,UtranCell=GRY502A,Pch=1 5164 !!!! Processing failure :se.ericsson.cello.moframework.MoNotFoundException TAG :"MoNotFound" VARIABLES :"$dName" = "ManagedElement=1,RncFunction=1,UtranCell=GRY502A,Rach=1" !!!! Processing failure :se.ericsson.cello.moframework.MoNotFoundException TAG :"MoNotFound" VARIABLES :"$dName" = "ManagedElement=1,RncFunction=1,UtranCell=GRY502A,Rach=1" RncFunction=1,UtranCell=GRY502B,Pch=1 5165 !!!! Processing failure :se.ericsson.cello.moframework.MoNotFoundException TAG :"MoNotFound" VARIABLES :"$dName" = "ManagedElement=1,RncFunction=1,UtranCell=GRY502A,Rach=1" !!!! Processing failure :se.ericsson.cello.moframework.MoNotFoundException TAG :"MoNotFound" VARIABLES :"$dName" = "ManagedElement=1,RncFunction=1,UtranCell=GRY502A,Rach=1" RncFunction=1,UtranCell=GRY502C,Pch=1 6042 !!!! Processing failure :se.ericsson.cello.moframework.MoNotFoundException TAG :"MoNotFound" VARIABLES :"$dName" = "ManagedElement=1,RncFunction=1,UtranCell=GRY502A,Rach=1" !!!! Processing failure :se.ericsson.cello.moframework.MoNotFoundException TAG :"MoNotFound" VARIABLES :"$dName" = "ManagedElement=1,RncFunction=1,UtranCell=GRY502A,Rach=1" RncFunction=1,UtranCell=GRY502A,Fach=1 6043 !!!! Processing failure :se.ericsson.cello.moframework.MoNotFoundException TAG :"MoNotFound" VARIABLES :"$dName" = "ManagedElement=1,RncFunction=1,UtranCell=GRY502A,Rach=1" !!!! Processing failure :se.ericsson.cello.moframework.MoNotFoundException TAG :"MoNotFound" VARIABLES :"$dName" = "ManagedElement=1,RncFunction=1,UtranCell=GRY502A,Rach=1" RncFunction=1,UtranCell=GRY502B,Fach=1 6044 !!!! Processing failure :se.ericsson.cello.moframework.MoNotFoundException TAG :"MoNotFound" VARIABLES :"$dName" = "ManagedElement=1,RncFunction=1,UtranCell=GRY502A,Rach=1" !!!! Processing failure :se.ericsson.cello.moframework.MoNotFoundException TAG :"MoNotFound" VARIABLES :"$dName" = "ManagedElement=1,RncFunction=1,UtranCell=GRY502A,Rach=1" RncFunction=1,UtranCell=GRY502C,Fach=1

6337 !!!! Processing failure :se.ericsson.cello.moframework.MoNotFoundException TAG :"MoNotFound" VARIABLES :"$dName" = "ManagedElement=1,RncFunction=1,UtranCell=GRY502A,Rach=1" !!!! Processing failure :se.ericsson.cello.moframework.MoNotFoundException TAG :"MoNotFound" VARIABLES :"$dName" = "ManagedElement=1,RncFunction=1,UtranCell=GRY502A,Rach=1" RncFunction=1,IubLink=Iub_GRY502,NbapCommon=1 8598 !!!! Processing failure :se.ericsson.cello.moframework.MoNotFoundException TAG :"MoNotFound" VARIABLES :"$dName" = "ManagedElement=1,RncFunction=1,UtranCell=GRY502A,Rach=1" !!!! Processing failure :se.ericsson.cello.moframework.MoNotFoundException TAG :"MoNotFound" VARIABLES :"$dName" = "ManagedElement=1,RncFunction=1,UtranCell=GRY502A,Rach=1" RncFunction=1,IubLink=Iub_GRY502,NodeSynchTp=1 8599 !!!! Processing failure :se.ericsson.cello.moframework.MoNotFoundException TAG :"MoNotFound" VARIABLES :"$dName" = "ManagedElement=1,RncFunction=1,UtranCell=GRY502A,Rach=1" !!!! Processing failure :se.ericsson.cello.moframework.MoNotFoundException TAG :"MoNotFound" VARIABLES :"$dName" = "ManagedElement=1,RncFunction=1,UtranCell=GRY502A,Rach=1" RncFunction=1,IubLink=Iub_GRY502,NodeSynchTp=2 8892 !!!! Processing failure :se.ericsson.cello.moframework.MoNotFoundException TAG :"MoNotFound" VARIABLES :"$dName" = "ManagedElement=1,RncFunction=1,UtranCell=GRY502A,Rach=1" !!!! Processing failure :se.ericsson.cello.moframework.MoNotFoundException TAG :"MoNotFound" VARIABLES :"$dName" = "ManagedElement=1,RncFunction=1,UtranCell=GRY502A,Rach=1" RncFunction=1,IubLink=Iub_GRY502,NbapDedicated=1 9185 !!!! Processing failure :se.ericsson.cello.moframework.MoNotFoundException TAG :"MoNotFound" VARIABLES :"$dName" = "ManagedElement=1,RncFunction=1,UtranCell=GRY502A,Rach=1" RncFunction=1,IubLink=Iub_GRY502 10062 !!!! Processing failure :se.ericsson.cello.moframework.MoNotFoundException TAG :"MoNotFound" VARIABLES :"$dName" = "ManagedElement=1,RncFunction=1,UtranCell=GRY502A,Rach=1" !!!! Processing failure :se.ericsson.cello.moframework.MoNotFoundException TAG :"MoNotFound" VARIABLES :"$dName" = "ManagedElement=1,RncFunction=1,UtranCell=GRY502A,Rach=1" RncFunction=1,UtranCell=GRY502A 10063 !!!! Processing failure :se.ericsson.cello.moframework.MoNotFoundException TAG :"MoNotFound" VARIABLES :"$dName" = "ManagedElement=1,RncFunction=1,UtranCell=GRY502A,Rach=1" !!!! Processing failure :se.ericsson.cello.moframework.MoNotFoundException TAG :"MoNotFound" VARIABLES :"$dName" = "ManagedElement=1,RncFunction=1,UtranCell=GRY502A,Rach=1" RncFunction=1,UtranCell=GRY502B 10064 !!!! Processing failure :se.ericsson.cello.moframework.MoNotFoundException TAG :"MoNotFound" VARIABLES :"$dName" = "ManagedElement=1,RncFunction=1,UtranCell=GRY502A,Rach=1" !!!! Processing failure :se.ericsson.cello.moframework.MoNotFoundException TAG :"MoNotFound" VARIABLES :"$dName" = "ManagedElement=1,RncFunction=1,UtranCell=GRY502A,Rach=1" RncFunction=1,UtranCell=GRY502C =================================================================================== Total: 20 MOs 3RR01> lst imagroup=ES-1-4-1-ima48 070524-06:57:29 172.24.12.207 7.0 RESTRICTED RNC_NODE_MODEL_F_5_2 stopfile=/tmp/19957 =================================================================================== Proxy Adm State Op. State MO =================================================================================== 16260 !!!! Processing failure :se.ericsson.cello.moframework.MoNotFoundException TAG :"MoNotFound" VARIABLES :"$dName" = "ManagedElement=1,TransportNetwork=1,ImaGroup=ES-1-4-1-ima48" TransportNetwork=1,ImaGroup=ES-1-4-1-ima48 16440 !!!! Processing failure :se.ericsson.cello.moframework.MoNotFoundException TAG :"MoNotFound" VARIABLES :"$dName" = "ManagedElement=1,TransportNetwork=1,ImaGroup=ES-1-4-1-ima48" TransportNetwork=1,ImaGroup=ES-1-4-1-ima48,ImaLink=1

16441 !!!! Processing failure :se.ericsson.cello.moframework.MoNotFoundException TAG :"MoNotFound" VARIABLES :"$dName" = "ManagedElement=1,TransportNetwork=1,ImaGroup=ES-1-4-1-ima48" TransportNetwork=1,ImaGroup=ES-1-4-1-ima48,ImaLink=2 16442 !!!! Processing failure :se.ericsson.cello.moframework.MoNotFoundException TAG :"MoNotFound" VARIABLES :"$dName" = "ManagedElement=1,TransportNetwork=1,ImaGroup=ES-1-4-1-ima48" TransportNetwork=1,ImaGroup=ES-1-4-1-ima48,ImaLink=3 =================================================================================== Total: 4 Mos /* Printout from lgo cmd */ 2007-05-24 01:01:26 MO-C *** CREATE CV: Au_CXP9012011_R8AL%2_070524_0100 2007-05-24 02:51:10 MO-C SET Equipment=1,Subrack=ES-1,Slot=4,PlugInUnit=1 administrativeState 0 2007-05-24 02:55:32 MO-C ACT Equipment=1,Subrack=ES-1,Slot=4,PlugInUnit=1 restart 2;1 {cold restart;Piu error} 2007-05-24 03:07:42 MO-C SET Equipment=1,Subrack=ES-1,Slot=4,PlugInUnit=1 administrativeState 1 2007-05-24 03:20:10 MO-C SET Equipment=1,Subrack=ES-1,Slot=4,PlugInUnit=1 administrativeState 0 2007-05-24 03:22:51 MO-C SET Equipment=1,Subrack=ES-1,Slot=4,PlugInUnit=1 administrativeState 1 2007-05-24 03:29:50 MO-C SET Equipment=1,Subrack=ES-1,Slot=4,PlugInUnit=1 administrativeState 0 2007-05-24 03:30:26 MO-C ACT Equipment=1,Subrack=ES-1,Slot=4,PlugInUnit=1 restart 2;1 2007-05-24 03:43:24 MO-C SET Equipment=1,Subrack=ES-1,Slot=4,PlugInUnit=1 administrativeState 1 2007-05-24 03:51:55 MO-C DEL TransportNetwork=1,Aal2RoutingCase=966101000100013 2007-05-24 03:52:53 MO-C DEL RncFunction=1,UtranCell=GRY393A,UtranRelation=GRY393A_GRY502B 2007-05-24 03:52:53 MO-C DEL RncFunction=1,UtranCell=GRY065C,UtranRelation=GRY065C_GRY502C 2007-05-24 03:52:53 MO-C DEL RncFunction=1,UtranCell=GRY065B,UtranRelation=GRY065B_GRY502A 2007-05-24 03:52:53 MO-C DEL RncFunction=1,UtranCell=GRY065B,UtranRelation=GRY065B_GRY502B 2007-05-24 03:52:53 MO-C DEL RncFunction=1,UtranCell=GRY065B,UtranRelation=GRY065B_GRY502C 2007-05-24 03:52:53 MO-C DEL RncFunction=1,UtranCell=GRY065A,UtranRelation=GRY065A_GRY502A 2007-05-24 03:52:53 MO-C DEL RncFunction=1,UtranCell=GRY065A,UtranRelation=GRY065A_GRY502C 2007-05-24 03:52:54 MO-C DEL RncFunction=1,UtranCell=GRY062C,UtranRelation=GRY062C_GRY502A 2007-05-24 03:52:54 MO-C DEL RncFunction=1,UtranCell=GRY062C,UtranRelation=GRY062C_GRY502B 2007-05-24 03:52:54 MO-C DEL RncFunction=1,UtranCell=GRY062C,UtranRelation=GRY062C_GRY502C 2007-05-24 03:52:54 MO-C DEL RncFunction=1,UtranCell=GRY062B,UtranRelation=GRY062B_GRY502B 2007-05-24 03:52:54 MO-C DEL RncFunction=1,UtranCell=GRY062A,UtranRelation=GRY062A_GRY502A 2007-05-24 03:52:54 MO-C DEL RncFunction=1,UtranCell=GRY062A,UtranRelation=GRY062A_GRY502B 2007-05-24 03:52:54 MO-C DEL RncFunction=1,UtranCell=GRY041A,UtranRelation=GRY041A_GRY502C 2007-05-24 03:52:54 MO-C DEL RncFunction=1,UtranCell=GRY363C,UtranRelation=GRY363C_GRY502A 2007-05-24 03:52:54 MO-C DEL RncFunction=1,UtranCell=GRY363C,UtranRelation=GRY363C_GRY502B

2007-05-24 03:52:54 MO-C DEL RncFunction=1,UtranCell=GRY363C,UtranRelation=GRY363C_GRY502C 2007-05-24 03:52:54 MO-C DEL RncFunction=1,UtranCell=GRY363B,UtranRelation=GRY363B_GRY502B 2007-05-24 03:52:55 MO-C DEL RncFunction=1,UtranCell=GRY363A,UtranRelation=GRY363A_GRY502A 2007-05-24 03:52:55 MO-C DEL RncFunction=1,UtranCell=GRY363A,UtranRelation=GRY363A_GRY502B 2007-05-24 03:52:55 MO-C DEL RncFunction=1,UtranCell=GRY363A,UtranRelation=GRY363A_GRY502C 2007-05-24 03:52:55 MO-C DEL RncFunction=1,UtranCell=GRY657B,UtranRelation=GRY657B_GRY502C 2007-05-24 03:52:55 MO-C DEL RncFunction=1,UtranCell=GRY657A,UtranRelation=GRY657A_GRY502C 2007-05-24 03:52:55 MO-C DEL RncFunction=1,UtranCell=GRY647C,UtranRelation=GRY647C_GRY502A 2007-05-24 03:52:55 MO-C DEL RncFunction=1,UtranCell=GRY647C,UtranRelation=GRY647C_GRY502C 2007-05-24 03:52:55 MO-C DEL RncFunction=1,UtranCell=GRY647B,UtranRelation=GRY647B_GRY502A 2007-05-24 03:52:55 MO-C DEL RncFunction=1,UtranCell=GRY647B,UtranRelation=GRY647B_GRY502C 2007-05-24 03:52:55 MO-C DEL RncFunction=1,UtranCell=GRY965C,UtranRelation=GRY965C_GRY502A 2007-05-24 03:52:55 MO-C DEL RncFunction=1,UtranCell=GRY913C,UtranRelation=GRY913C_GRY502B 2007-05-24 03:52:55 MO-C DEL RncFunction=1,UtranCell=GRY913A,UtranRelation=GRY913A_GRY502A 2007-05-24 03:52:56 MO-C DEL RncFunction=1,UtranCell=GRY913A,UtranRelation=GRY913A_GRY502B 2007-05-24 03:52:56 MO-C DEL RncFunction=1,UtranCell=GRI002B,UtranRelation=GRI002B_GRY502A 2007-05-24 03:52:56 MO-C DEL RncFunction=1,UtranCell=GRY536C,UtranRelation=GRY536C_GRY502B 2007-05-24 03:52:56 MO-C DEL RncFunction=1,UtranCell=GRY536A,UtranRelation=GRY536A_GRY502B 2007-05-24 03:52:56 MO-C DEL RncFunction=1,UtranCell=GRY849A,UtranRelation=GRY849A_GRY502B 2007-05-24 03:52:56 MO-C DEL RncFunction=1,UtranCell=GRY849A,UtranRelation=GRY849A_GRY502C 2007-05-24 03:52:56 MO-C DEL RncFunction=1,UtranCell=GRY843B,UtranRelation=GRY843B_GRY502A 2007-05-24 03:52:56 MO-C DEL RncFunction=1,UtranCell=GRY445C,UtranRelation=GRY445C_GRY502A 2007-05-24 03:52:56 MO-C DEL RncFunction=1,UtranCell=GRY445C,UtranRelation=GRY445C_GRY502C 2007-05-24 03:52:56 MO-C DEL RncFunction=1,UtranCell=GRY445B,UtranRelation=GRY445B_GRY502A 2007-05-24 03:52:56 MO-C DEL RncFunction=1,UtranCell=GRY445B,UtranRelation=GRY445B_GRY502B 2007-05-24 03:52:56 MO-C DEL RncFunction=1,UtranCell=GRY445B,UtranRelation=GRY445B_GRY502C 2007-05-24 03:52:56 MO-C DEL RncFunction=1,UtranCell=GRY445A,UtranRelation=GRY445A_GRY502A 2007-05-24 03:52:57 MO-C DEL RncFunction=1,UtranCell=GRY744C,UtranRelation=GRY744C_GRY502A 2007-05-24 03:52:57 MO-C DEL RncFunction=1,UtranCell=GRY744B,UtranRelation=GRY744B_GRY502A 2007-05-24 03:52:57 MO-C DEL RncFunction=1,UtranCell=GRY723B,UtranRelation=GRY723B_GRY502C 2007-05-24 03:52:57 MO-C DEL RncFunction=1,UtranCell=GCW617B,UtranRelation=GCW617B_GRY502A 2007-05-24 03:52:57 MO-C DEL RncFunction=1,UtranCell=GCW617B,UtranRelation=GCW617B_GRY502B

2007-05-24 03:52:57 MO-C DEL RncFunction=1,UtranCell=GCW617B,UtranRelation=GCW617B_GRY502C 2007-05-24 03:52:57 MO-C DEL RncFunction=1,UtranCell=GCW617A,UtranRelation=GCW617A_GRY502A 2007-05-24 03:52:57 MO-C DEL RncFunction=1,UtranCell=GCW617A,UtranRelation=GCW617A_GRY502B 2007-05-24 03:52:57 MO-C DEL RncFunction=1,UtranCell=GCW617A,UtranRelation=GCW617A_GRY502C 2007-05-24 03:52:57 MO-C DEL RncFunction=1,IubLink=Iub_GRY502,NbapCommon=1 2007-05-24 03:52:57 MO-C DEL RncFunction=1,IubLink=Iub_GRY502,NbapDedicated=1 2007-05-24 03:52:57 MO-C DEL RncFunction=1,IubLink=Iub_GRY502,NodeSynchTp=1 2007-05-24 03:52:58 MO-C DEL RncFunction=1,IubLink=Iub_GRY502,NodeSynchTp=2 2007-05-24 03:52:58 MO-C DEL RncFunction=1,UtranCell=GRY502A,GsmRelation=GRY502A_ZRY502A 2007-05-24 03:52:58 MO-C DEL RncFunction=1,UtranCell=GRY502A,UtranRelation=GRY502A_GRY965C 2007-05-24 03:52:58 MO-C DEL RncFunction=1,UtranCell=GRY502A,UtranRelation=GRY502A_GRY647B 2007-05-24 03:52:58 MO-C DEL RncFunction=1,UtranCell=GRY502A,UtranRelation=GRY502A_GRY647C 2007-05-24 03:52:58 MO-C DEL RncFunction=1,UtranCell=GRY502A,Hsdsch=1 2007-05-24 03:52:58 MO-C DEL RncFunction=1,UtranCell=GRY502A,UtranRelation=GRY502A_GRY363A 2007-05-24 03:52:59 MO-C DEL RncFunction=1,UtranCell=GRY502A,UtranRelation=GRY502A_GRY363C 2007-05-24 03:52:59 MO-C DEL RncFunction=1,UtranCell=GRY502A,UtranRelation=GRY502A_GRY062A 2007-05-24 03:52:59 MO-C DEL RncFunction=1,UtranCell=GRY502A,UtranRelation=GRY502A_GRY062C 2007-05-24 03:52:59 MO-C DEL RncFunction=1,UtranCell=GRY502A,UtranRelation=GRY502A_GRY065A 2007-05-24 03:52:59 MO-C DEL RncFunction=1,UtranCell=GRY502A,UtranRelation=GRY502A_GRY065B 2007-05-24 03:52:59 MO-C DEL RncFunction=1,UtranCell=GRY502A,UtranRelation=GRY502A_GCW617A 2007-05-24 03:52:59 MO-C DEL RncFunction=1,UtranCell=GRY502A,UtranRelation=GRY502A_GCW617B 2007-05-24 03:52:59 MO-C DEL RncFunction=1,UtranCell=GRY502A,GsmRelation=GRY502A_URY502A 2007-05-24 03:52:59 MO-C DEL RncFunction=1,UtranCell=GRY502A,UtranRelation=GRY502A_GRY744B 2007-05-24 03:52:59 MO-C DEL RncFunction=1,UtranCell=GRY502A,UtranRelation=GRY502A_GRY744C 2007-05-24 03:52:59 MO-C DEL RncFunction=1,UtranCell=GRY502A,UtranRelation=GRY502A_GRY445A 2007-05-24 03:53:00 MO-C DEL RncFunction=1,UtranCell=GRY502A,UtranRelation=GRY502A_GRY445B 2007-05-24 03:53:00 MO-C DEL RncFunction=1,UtranCell=GRY502A,UtranRelation=GRY502A_GRY445C 2007-05-24 03:53:00 MO-C DEL RncFunction=1,UtranCell=GRY502A,GsmRelation=GRY502A_ZRY010A 2007-05-24 03:53:00 MO-C DEL RncFunction=1,UtranCell=GRY502A,GsmRelation=GRY502A_ZRY010C 2007-05-24 03:53:00 MO-C DEL RncFunction=1,UtranCell=GRY502A,Pch=1 2007-05-24 03:53:00 MO-C DEL RncFunction=1,UtranCell=GRY502A,Rach=1 2007-05-24 03:53:00 MO-C DEL RncFunction=1,UtranCell=GRY502A,UtranRelation=GRY502A_GRY502B 2007-05-24 03:53:00 MO-C DEL RncFunction=1,UtranCell=GRY502A,UtranRelation=GRY502A_GRY502C 2007-05-24 03:53:00 MO-C DEL RncFunction=1,UtranCell=GRY502A,UtranRelation=GRY502A_GRY843B 2007-05-24 03:53:01 MO-C DEL RncFunction=1,UtranCell=GRY502A,GsmRelation=GRY502A_ZRY402A

2007-05-24 03:53:01 MO-C DEL RncFunction=1,UtranCell=GRY502A,GsmRelation=GRY502A_ZRY402C 2007-05-24 03:53:01 MO-C DEL RncFunction=1,UtranCell=GRY502A,GsmRelation=GRY502A_COW617B 2007-05-24 03:53:01 MO-C DEL RncFunction=1,UtranCell=GRY502A,UtranRelation=GRY502A_GRI002B 2007-05-24 03:53:01 MO-C DEL RncFunction=1,UtranCell=GRY502A,GsmRelation=GRY502A_ZRY445A 2007-05-24 03:53:01 MO-C DEL RncFunction=1,UtranCell=GRY502A,GsmRelation=GRY502A_ZRY445B 2007-05-24 03:53:01 MO-C DEL RncFunction=1,UtranCell=GRY502A,GsmRelation=GRY502A_ZRY445C 2007-05-24 03:53:01 MO-C DEL RncFunction=1,UtranCell=GRY502A,Fach=1 2007-05-24 03:53:01 MO-C DEL RncFunction=1,UtranCell=GRY502A,UtranRelation=GRY502A_GRY913A 2007-05-24 03:53:01 MO-C DEL RncFunction=1,UtranCell=GRY502B,GsmRelation=GRY502B_COW617A 2007-05-24 03:53:01 MO-C DEL RncFunction=1,UtranCell=GRY502B,UtranRelation=GRY502B_GRY913A 2007-05-24 03:53:01 MO-C DEL RncFunction=1,UtranCell=GRY502B,UtranRelation=GRY502B_GRY913C 2007-05-24 03:53:01 MO-C DEL RncFunction=1,UtranCell=GRY502B,UtranRelation=GRY502B_GRY363A 2007-05-24 03:53:01 MO-C DEL RncFunction=1,UtranCell=GRY502B,UtranRelation=GRY502B_GRY363B 2007-05-24 03:53:02 MO-C DEL RncFunction=1,UtranCell=GRY502B,UtranRelation=GRY502B_GRY363C 2007-05-24 03:53:02 MO-C DEL RncFunction=1,UtranCell=GRY502B,UtranRelation=GRY502B_GRY062A 2007-05-24 03:53:02 MO-C DEL RncFunction=1,UtranCell=GRY502B,UtranRelation=GRY502B_GRY062B 2007-05-24 03:53:02 MO-C DEL RncFunction=1,UtranCell=GRY502B,UtranRelation=GRY502B_GRY062C 2007-05-24 03:53:02 MO-C DEL RncFunction=1,UtranCell=GRY502B,UtranRelation=GRY502B_GRY065B 2007-05-24 03:53:02 MO-C DEL RncFunction=1,UtranCell=GRY502B,UtranRelation=GRY502B_GRY393A 2007-05-24 03:53:02 MO-C DEL RncFunction=1,UtranCell=GRY502B,UtranRelation=GRY502B_GCW617A 2007-05-24 03:53:03 MO-C DEL RncFunction=1,UtranCell=GRY502B,UtranRelation=GRY502B_GCW617B 2007-05-24 03:53:03 MO-C DEL RncFunction=1,UtranCell=GRY502B,GsmRelation=GRY502B_ZRY502B 2007-05-24 03:53:03 MO-C DEL RncFunction=1,UtranCell=GRY502B,UtranRelation=GRY502B_GRY445B 2007-05-24 03:53:03 MO-C DEL RncFunction=1,UtranCell=GRY502B,GsmRelation=GRY502B_ZRY570B 2007-05-24 03:53:03 MO-C DEL RncFunction=1,UtranCell=GRY502B,GsmRelation=GRY502B_ZRY570C 2007-05-24 03:53:03 MO-C DEL RncFunction=1,UtranCell=GRY502B,Rach=1 2007-05-24 03:53:03 MO-C DEL RncFunction=1,UtranCell=GRY502B,GsmRelation=GRY502B_URY502B 2007-05-24 03:53:03 MO-C DEL RncFunction=1,UtranCell=GRY502B,UtranRelation=GRY502B_GRY502A 2007-05-24 03:53:03 MO-C DEL RncFunction=1,UtranCell=GRY502B,UtranRelation=GRY502B_GRY502C 2007-05-24 03:53:04 MO-C DEL RncFunction=1,UtranCell=GRY502B,UtranRelation=GRY502B_GRY849A 2007-05-24 03:53:04 MO-C DEL RncFunction=1,UtranCell=GRY502B,Hsdsch=1 2007-05-24 03:53:04 MO-C DEL RncFunction=1,UtranCell=GRY502B,UtranRelation=GRY502B_GRY536A 2007-05-24 03:53:04 MO-C DEL RncFunction=1,UtranCell=GRY502B,UtranRelation=GRY502B_GRY536C 2007-05-24 03:53:04 MO-C DEL RncFunction=1,UtranCell=GRY502B,Fach=1

2007-05-24 03:53:04 MO-C DEL RncFunction=1,UtranCell=GRY502B,Pch=1 2007-05-24 03:53:04 MO-C DEL RncFunction=1,UtranCell=GRY502B,GsmRelation=GRY502B_ZRY363B 2007-05-24 03:53:04 MO-C DEL RncFunction=1,UtranCell=GRY502B,GsmRelation=GRY502B_ZRY363C 2007-05-24 03:53:04 MO-C DEL RncFunction=1,UtranCell=GRY502C,GsmRelation=GRY502C_ZRY065A 2007-05-24 03:53:04 MO-C DEL RncFunction=1,UtranCell=GRY502C,GsmRelation=GRY502C_ZRY065B 2007-05-24 03:53:04 MO-C DEL RncFunction=1,UtranCell=GRY502C,UtranRelation=GRY502C_GRY647B 2007-05-24 03:53:04 MO-C DEL RncFunction=1,UtranCell=GRY502C,UtranRelation=GRY502C_GRY647C 2007-05-24 03:53:04 MO-C DEL RncFunction=1,UtranCell=GRY502C,UtranRelation=GRY502C_GRY657A 2007-05-24 03:53:05 MO-C DEL RncFunction=1,UtranCell=GRY502C,UtranRelation=GRY502C_GRY657B 2007-05-24 03:53:05 MO-C DEL RncFunction=1,UtranCell=GRY502C,UtranRelation=GRY502C_GRY363A 2007-05-24 03:53:05 MO-C DEL RncFunction=1,UtranCell=GRY502C,UtranRelation=GRY502C_GRY363C 2007-05-24 03:53:05 MO-C DEL RncFunction=1,UtranCell=GRY502C,UtranRelation=GRY502C_GRY041A 2007-05-24 03:53:05 MO-C DEL RncFunction=1,UtranCell=GRY502C,UtranRelation=GRY502C_GRY062C 2007-05-24 03:53:05 MO-C DEL RncFunction=1,UtranCell=GRY502C,UtranRelation=GRY502C_GRY065A 2007-05-24 03:53:05 MO-C DEL RncFunction=1,UtranCell=GRY502C,UtranRelation=GRY502C_GRY065B 2007-05-24 03:53:05 MO-C DEL RncFunction=1,UtranCell=GRY502C,UtranRelation=GRY502C_GRY065C 2007-05-24 03:53:05 MO-C DEL RncFunction=1,UtranCell=GRY502C,UtranRelation=GRY502C_GCW617A 2007-05-24 03:53:05 MO-C DEL RncFunction=1,UtranCell=GRY502C,UtranRelation=GRY502C_GCW617B 2007-05-24 03:53:05 MO-C DEL RncFunction=1,UtranCell=GRY502C,Hsdsch=1 2007-05-24 03:53:05 MO-C DEL RncFunction=1,UtranCell=GRY502C,GsmRelation=GRY502C_COW617B 2007-05-24 03:53:06 MO-C DEL RncFunction=1,UtranCell=GRY502C,GsmRelation=GRY502C_ZRY445C 2007-05-24 03:53:06 MO-C DEL RncFunction=1,UtranCell=GRY502C,UtranRelation=GRY502C_GRY723B 2007-05-24 03:53:06 MO-C DEL RncFunction=1,UtranCell=GRY502C,UtranRelation=GRY502C_GRY445B 2007-05-24 03:53:06 MO-C DEL RncFunction=1,UtranCell=GRY502C,UtranRelation=GRY502C_GRY445C 2007-05-24 03:53:06 MO-C DEL RncFunction=1,UtranCell=GRY502C,Rach=1 2007-05-24 03:53:06 MO-C DEL RncFunction=1,UtranCell=GRY502C,GsmRelation=GRY502C_ZRY502A 2007-05-24 03:53:06 MO-C DEL RncFunction=1,UtranCell=GRY502C,GsmRelation=GRY502C_ZRY502B 2007-05-24 03:53:06 MO-C DEL RncFunction=1,UtranCell=GRY502C,GsmRelation=GRY502C_ZRY502C 2007-05-24 03:53:06 MO-C DEL RncFunction=1,UtranCell=GRY502C,Fach=1 2007-05-24 03:53:06 MO-C DEL RncFunction=1,UtranCell=GRY502C,UtranRelation=GRY502C_GRY502A 2007-05-24 03:53:06 MO-C DEL RncFunction=1,UtranCell=GRY502C,UtranRelation=GRY502C_GRY502B 2007-05-24 03:53:06 MO-C DEL RncFunction=1,UtranCell=GRY502C,UtranRelation=GRY502C_GRY849A 2007-05-24 03:53:06 MO-C DEL RncFunction=1,UtranCell=GRY502C,GsmRelation=GRY502C_URY502C 2007-05-24 03:53:06 MO-C DEL RncFunction=1,UtranCell=GRY502C,Pch=1 2007-05-24 03:54:32 MO-C DEL RncFunction=1,IubLink=Iub_GRY502,NodeSynch=1

2007-05-24 03:54:32 MO-C DEL RncFunction=1,UtranCell=GRY502A 2007-05-24 03:54:33 MO-C DEL RncFunction=1,UtranCell=GRY502B 2007-05-24 03:54:34 MO-C DEL RncFunction=1,UtranCell=GRY502C 2007-05-24 03:54:48 MO-C DEL RncFunction=1,IubLink=Iub_GRY502 2007-05-24 03:55:22 MO-C SET TransportNetwork=1,Aal2PathVccTp=b1013a1 administrativeState 0 2007-05-24 03:55:22 MO-C SET TransportNetwork=1,Aal2PathVccTp=b1013a2 administrativeState 0 2007-05-24 03:55:22 MO-C DEL TransportNetwork=1,Aal2Sp=1,Aal2Ap=b1013,Aal2PathDistributionUnit=1 2007-05-24 03:55:22 MO-C SET TransportNetwork=1,Aal2PathVccTp=b1013a1 administrativeState 1 2007-05-24 03:55:22 MO-C SET TransportNetwork=1,Aal2PathVccTp=b1013a2 administrativeState 1 2007-05-24 03:55:23 MO-C DEL TransportNetwork=1,UniSaalTp=b1013ca 2007-05-24 03:55:23 MO-C DEL TransportNetwork=1,UniSaalTp=b1013cb 2007-05-24 03:55:23 MO-C DEL TransportNetwork=1,UniSaalTp=b1013da 2007-05-24 03:55:23 MO-C DEL TransportNetwork=1,UniSaalTp=b1013db 2007-05-24 03:55:23 MO-C DEL TransportNetwork=1,Aal0TpVccTp=b1013sa1 2007-05-24 03:55:23 MO-C DEL TransportNetwork=1,Aal0TpVccTp=b1013sb1 2007-05-24 03:55:23 MO-C DEL TransportNetwork=1,AtmCrossConnection=b1013ia 2007-05-24 03:55:24 MO-C DEL TransportNetwork=1,AtmCrossConnection=b1013ib 2007-05-24 03:55:24 MO-C DEL TransportNetwork=1,Aal2PathVccTp=b1013a1 2007-05-24 03:55:24 MO-C DEL TransportNetwork=1,Aal2PathVccTp=b1013a2 2007-05-24 03:55:34 MO-C DEL TransportNetwork=1,Aal2Sp=1,Aal2Ap=b1013 2007-05-24 03:55:34 MO-C DEL TransportNetwork=1,UniSaalTp=b1013qa 2007-05-24 03:55:34 MO-C DEL TransportNetwork=1,UniSaalTp=b1013qb 2007-05-24 03:55:34 MO-C DEL TransportNetwork=1,Aal5TpVccTp=b1013ca 2007-05-24 03:55:35 MO-C DEL TransportNetwork=1,Aal5TpVccTp=b1013cb 2007-05-24 03:55:35 MO-C DEL TransportNetwork=1,Aal5TpVccTp=b1013da 2007-05-24 03:55:35 MO-C DEL TransportNetwork=1,Aal5TpVccTp=b1013db 2007-05-24 03:55:43 MO-C DEL TransportNetwork=1,Aal5TpVccTp=b1013qa 2007-05-24 03:55:43 MO-C DEL TransportNetwork=1,Aal5TpVccTp=b1013qb 2007-05-24 03:56:21 MO-C DEL TransportNetwork=1,AtmPort=ES-1-4-1-ima48,VplTp=vp1,VpcTp=1,VclTp=vc32 2007-05-24 03:56:21 MO-C DEL TransportNetwork=1,AtmPort=ES-1-4-1-ima48,VplTp=vp1,VpcTp=1,VclTp=vc33 2007-05-24 03:56:21 MO-C DEL TransportNetwork=1,AtmPort=ES-1-4-1-ima48,VplTp=vp1,VpcTp=1,VclTp=vc34 2007-05-24 03:56:21 MO-C DEL TransportNetwork=1,AtmPort=ES-1-4-1-ima48,VplTp=vp1,VpcTp=1,VclTp=vc35 2007-05-24 03:56:21 MO-C DEL TransportNetwork=1,AtmPort=ES-1-4-1-ima48,VplTp=vp1,VpcTp=1,VclTp=vc36 2007-05-24 03:56:21 MO-C DEL TransportNetwork=1,AtmPort=ES-1-4-1-ima48,VplTp=vp1,VpcTp=1,VclTp=vc37 2007-05-24 03:56:21 MO-C DEL TransportNetwork=1,AtmPort=ES-1-4-1-ima48,VplTp=vp1,VpcTp=1,VclTp=vc38 2007-05-24 03:56:21 MO-C DEL TransportNetwork=1,AtmPort=ES-1-4-1-ima48,VplTp=vp1,VpcTp=1,VclTp=vc39 2007-05-24 03:56:21 MO-C DEL TransportNetwork=1,AtmPort=ES-1-4-1-ima48,VplTp=vp1,VpcTp=1,VclTp=vc40 2007-05-24 03:56:22 MO-C DEL TransportNetwork=1,AtmPort=ES-1-4-1-ima48,VplTp=vp1,VpcTp=1,VclTp=vc43 2007-05-24 03:56:22 MO-C DEL TransportNetwork=1,AtmPort=ES-1-4-1-ima48,VplTp=vp1,VpcTp=1,VclTp=vc44 2007-05-24 03:56:22 MO-C DEL TransportNetwork=1,AtmPort=ES-1-4-1-ima48,VplTp=vp1,VpcTp=1,VclTp=vc45 2007-05-24 03:56:30 MO-C DEL TransportNetwork=1,AtmPort=ES-1-4-1-ima48,VplTp=vp1,VpcTp=1 2007-05-24 03:56:39 MO-C DEL TransportNetwork=1,AtmPort=ES-1-4-1-ima48,VplTp=vp1 2007-05-24 03:56:46 MO-C DEL TransportNetwork=1,AtmPort=ES-1-4-1-ima48 2007-05-24 03:57:16 MO-C DEL TransportNetwork=1,ImaGroup=ES-1-4-1-ima48 2007-05-24 03:57:55 MO-C CRE TransportNetwork=1,ImaGroup=ES-1-4-1-ima48

2007-05-24 03:57:57 MO-C SET TransportNetwork=1,ImaGroup=ES-1-4-1-ima48 requiredNumberOfLinks 3 2007-05-24 03:57:57 MO-C CRE TransportNetwork=1,AtmPort=ES-1-4-1-ima48 2007-05-24 03:57:59 MO-C CRE TransportNetwork=1,AtmPort=ES-1-4-1-ima48,VplTp=vp1 2007-05-24 03:58:00 MO-C CRE TransportNetwork=1,AtmPort=ES-1-4-1-ima48,VplTp=vp1,VpcTp=1 2007-05-24 03:58:06 MO-C CRE TransportNetwork=1,AtmPort=ES-1-4-1-ima48,VplTp=vp1,VpcTp=1,VclTp=vc45 2007-05-24 03:58:07 MO-C CRE TransportNetwork=1,AtmPort=ES-1-4-1-ima48,VplTp=vp1,VpcTp=1,VclTp=vc44 2007-05-24 03:58:09 MO-C CRE TransportNetwork=1,AtmPort=ES-1-4-1-ima48,VplTp=vp1,VpcTp=1,VclTp=vc43 2007-05-24 03:58:11 MO-C CRE TransportNetwork=1,AtmPort=ES-1-4-1-ima48,VplTp=vp1,VpcTp=1,VclTp=vc40 2007-05-24 03:58:12 MO-C CRE TransportNetwork=1,AtmPort=ES-1-4-1-ima48,VplTp=vp1,VpcTp=1,VclTp=vc39 2007-05-24 03:58:13 MO-C CRE TransportNetwork=1,AtmPort=ES-1-4-1-ima48,VplTp=vp1,VpcTp=1,VclTp=vc38 2007-05-24 03:58:15 MO-C CRE TransportNetwork=1,AtmPort=ES-1-4-1-ima48,VplTp=vp1,VpcTp=1,VclTp=vc37 2007-05-24 03:58:16 MO-C CRE TransportNetwork=1,AtmPort=ES-1-4-1-ima48,VplTp=vp1,VpcTp=1,VclTp=vc36 2007-05-24 03:58:18 MO-C CRE TransportNetwork=1,AtmPort=ES-1-4-1-ima48,VplTp=vp1,VpcTp=1,VclTp=vc35 2007-05-24 03:58:19 MO-C CRE TransportNetwork=1,AtmPort=ES-1-4-1-ima48,VplTp=vp1,VpcTp=1,VclTp=vc34 2007-05-24 03:58:21 MO-C CRE TransportNetwork=1,AtmPort=ES-1-4-1-ima48,VplTp=vp1,VpcTp=1,VclTp=vc33 2007-05-24 03:58:22 MO-C CRE TransportNetwork=1,AtmPort=ES-1-4-1-ima48,VplTp=vp1,VpcTp=1,VclTp=vc32 2007-05-24 03:58:24 MO-C CRE TransportNetwork=1,Aal5TpVccTp=b1013qb 2007-05-24 03:58:29 MO-C CRE TransportNetwork=1,Aal5TpVccTp=b1013qa 2007-05-24 03:58:35 MO-C CRE TransportNetwork=1,Aal5TpVccTp=b1013db 2007-05-24 03:58:41 MO-C CRE TransportNetwork=1,Aal5TpVccTp=b1013da 2007-05-24 03:58:47 MO-C CRE TransportNetwork=1,Aal5TpVccTp=b1013cb 2007-05-24 03:58:53 MO-C CRE TransportNetwork=1,Aal5TpVccTp=b1013ca 2007-05-24 03:58:58 MO-C CRE TransportNetwork=1,UniSaalTp=b1013qb 2007-05-24 03:59:00 MO-C CRE TransportNetwork=1,UniSaalTp=b1013qa 2007-05-24 03:59:01 MO-C CRE TransportNetwork=1,Aal2Sp=1,Aal2Ap=b1013 2007-05-24 03:59:04 MO-C SET TransportNetwork=1,Aal2Sp=1,Aal2Ap=b1013 aal2QoSCodePointProfileId Aal2QosCodePointProfile=1 2007-05-24 03:59:04 MO-C CRE TransportNetwork=1,Aal2PathVccTp=b1013a2 2007-05-24 03:59:08 MO-C SET TransportNetwork=1,Aal2PathVccTp=b1013a2 aal2QoSAvailableProfiles 4 2007-05-24 03:59:12 MO-C CRE TransportNetwork=1,Aal2PathVccTp=b1013a1 2007-05-24 03:59:21 MO-C SET TransportNetwork=1,Aal2PathVccTp=b1013a1 aal2QoSAvailableProfiles 3 2007-05-24 03:59:21 MO-C CRE TransportNetwork=1,AtmCrossConnection=b1013ib 2007-05-24 03:59:23 MO-C CRE TransportNetwork=1,AtmCrossConnection=b1013ia 2007-05-24 03:59:24 MO-C CRE TransportNetwork=1,Aal0TpVccTp=b1013sb1 2007-05-24 03:59:30 MO-C CRE TransportNetwork=1,Aal0TpVccTp=b1013sa1 2007-05-24 03:59:35 MO-C CRE TransportNetwork=1,UniSaalTp=b1013db 2007-05-24 03:59:37 MO-C CRE TransportNetwork=1,UniSaalTp=b1013da 2007-05-24 03:59:38 MO-C CRE TransportNetwork=1,UniSaalTp=b1013cb 2007-05-24 03:59:39 MO-C CRE TransportNetwork=1,UniSaalTp=b1013ca 2007-05-24 03:59:41 MO-C CRE TransportNetwork=1,Aal2Sp=1,Aal2Ap=b1013,Aal2PathDistributionUnit=1 2007-05-24 03:59:43 MO-C SET TransportNetwork=1,Aal2Sp=1,Aal2Ap=b1013,Aal2PathDistributionUnit=1 aal2PathVccTpList Aal2PathVccTp=b1013a1;Aal2PathVccTp=b1013a2 2007-05-24 03:59:43 MO-C CRE RncFunction=1,IubLink=Iub_GRY502 2007-05-24 03:59:49 MO-C SET RncFunction=1,IubLink=Iub_GRY502 userLabel Iub_GRY502 2007-05-24 03:59:50 MO-C CRE RncFunction=1,UtranCell=GRY502C

2007-05-24 03:59:55 MO-C SET RncFunction=1,UtranCell=GRY502C directedRetryTarget null 2007-05-24 03:59:58 MO-C SET RncFunction=1,UtranCell=GRY502C utranCellPosition 2007-05-24 04:00:17 MO-C SET RncFunction=1,UtranCell=GRY502C userLabel GRY502C 2007-05-24 04:00:23 MO-C SET RncFunction=1,UtranCell=GRY502C usedFreqThresh2dRscp -102 2007-05-24 04:00:26 MO-C SET RncFunction=1,UtranCell=GRY502C aseUlAdmOffset 0 2007-05-24 04:00:34 MO-C SET RncFunction=1,UtranCell=GRY502C maximumTransmissionPower 420 2007-05-24 04:00:36 MO-C SET RncFunction=1,UtranCell=GRY502C aseUlAdm 500 2007-05-24 04:00:39 MO-C SET RncFunction=1,UtranCell=GRY502C beMarginAseDl 0 2007-05-24 04:00:42 MO-C SET RncFunction=1,UtranCell=GRY502C routingAreaRef RncFunction=1,LocationArea=3111,RoutingArea=1 2007-05-24 04:01:00 MO-C SET RncFunction=1,UtranCell=GRY502C administrativeState 1 2007-05-24 04:01:05 MO-C SET RncFunction=1,UtranCell=GRY502C sHcsRat 3 2007-05-24 04:01:07 MO-C SET RncFunction=1,UtranCell=GRY502C beMarginAseUl 0 2007-05-24 04:01:11 MO-C SET RncFunction=1,UtranCell=GRY502C usedFreqThresh2dEcno -13 2007-05-24 04:01:23 MO-C SET RncFunction=1,UtranCell=GRY502C aseDlAdm 500 2007-05-24 04:01:34 MO-C CRE RncFunction=1,UtranCell=GRY502B 2007-05-24 04:01:49 MO-C SET RncFunction=1,UtranCell=GRY502B aseDlAdm 500 2007-05-24 04:01:58 MO-C SET RncFunction=1,UtranCell=GRY502B administrativeState 1 2007-05-24 04:02:15 MO-C SET RncFunction=1,UtranCell=GRY502B usedFreqThresh2dEcno -13 2007-05-24 04:02:20 MO-C SET RncFunction=1,UtranCell=GRY502B utranCellPosition 2007-05-24 04:02:25 MO-C SET RncFunction=1,UtranCell=GRY502B beMarginAseDl 0 2007-05-24 04:02:31 MO-C SET RncFunction=1,UtranCell=GRY502B directedRetryTarget null 2007-05-24 04:02:33 MO-C SET RncFunction=1,UtranCell=GRY502B maximumTransmissionPower 420 2007-05-24 04:02:34 MO-C SET RncFunction=1,UtranCell=GRY502B sHcsRat 3 2007-05-24 04:02:36 MO-C SET RncFunction=1,UtranCell=GRY502B aseUlAdm 500 2007-05-24 04:02:39 MO-C SET RncFunction=1,UtranCell=GRY502B routingAreaRef RncFunction=1,LocationArea=3111,RoutingArea=1 2007-05-24 04:02:45 MO-C SET RncFunction=1,UtranCell=GRY502B userLabel GRY502B 2007-05-24 04:02:46 MO-C SET RncFunction=1,UtranCell=GRY502B aseUlAdmOffset 0 2007-05-24 04:02:55 MO-C SET RncFunction=1,UtranCell=GRY502B beMarginAseUl 0 2007-05-24 04:03:09 MO-C SET RncFunction=1,UtranCell=GRY502B usedFreqThresh2dRscp -102 2007-05-24 04:03:11 MO-C CRE RncFunction=1,UtranCell=GRY502A 2007-05-24 04:03:15 MO-C SET RncFunction=1,UtranCell=GRY502A routingAreaRef RncFunction=1,LocationArea=3111,RoutingArea=1 2007-05-24 04:03:22 MO-C SET RncFunction=1,UtranCell=GRY502A usedFreqThresh2dEcno -13 2007-05-24 04:03:31 MO-C SET RncFunction=1,UtranCell=GRY502A userLabel GRY502A 2007-05-24 04:03:32 MO-C SET RncFunction=1,UtranCell=GRY502A directedRetryTarget null 2007-05-24 04:03:38 MO-C SET RncFunction=1,UtranCell=GRY502A aseDlAdm 500 2007-05-24 04:04:13 MO-C SET RncFunction=1,UtranCell=GRY502A beMarginAseDl 0 2007-05-24 04:04:18 MO-C SET RncFunction=1,UtranCell=GRY502A sHcsRat 3 2007-05-24 04:04:24 MO-C SET RncFunction=1,UtranCell=GRY502A usedFreqThresh2dRscp -102 2007-05-24 04:04:30 MO-C SET RncFunction=1,UtranCell=GRY502A administrativeState 1 2007-05-24 04:04:35 MO-C SET RncFunction=1,UtranCell=GRY502A maximumTransmissionPower 420 2007-05-24 04:04:38 MO-C SET RncFunction=1,UtranCell=GRY502A beMarginAseUl 0 2007-05-24 04:04:41 MO-C SET RncFunction=1,UtranCell=GRY502A utranCellPosition 2007-05-24 04:04:43 MO-C SET RncFunction=1,UtranCell=GRY502A aseUlAdm 500 2007-05-24 04:04:46 MO-C SET RncFunction=1,UtranCell=GRY502A aseUlAdmOffset 0 2007-05-24 04:04:49 MO-C CRE RncFunction=1,IubLink=Iub_GRY502,NodeSynch=1 2007-05-24 04:04:56 MO-C CRE RncFunction=1,UtranCell=GRY502C,Pch=1 2007-05-24 04:04:59 MO-C SET RncFunction=1,UtranCell=GRY502C,Pch=1 userLabel 2007-05-24 04:05:03 MO-C CRE RncFunction=1,UtranCell=GRY502C,GsmRelation=GRY502C_URY502C

2007-05-24 04:05:07 MO-C SET RncFunction=1,UtranCell=GRY502C,GsmRelation=GRY502C_URY502C selectionPriority 2 2007-05-24 04:05:08 MO-C CRE RncFunction=1,UtranCell=GRY502C,UtranRelation=GRY502C_GRY849A 2007-05-24 04:05:12 MO-C SET RncFunction=1,UtranCell=GRY502C,UtranRelation=GRY502C_GRY849A selectionPriority 16 2007-05-24 04:05:13 MO-C CRE RncFunction=1,UtranCell=GRY502C,UtranRelation=GRY502C_GRY502B 2007-05-24 04:05:16 MO-C SET RncFunction=1,UtranCell=GRY502C,UtranRelation=GRY502C_GRY502B selectionPriority 20 2007-05-24 04:05:18 MO-C CRE RncFunction=1,UtranCell=GRY502C,UtranRelation=GRY502C_GRY502A 2007-05-24 04:05:19 MO-C SET RncFunction=1,UtranCell=GRY502C,UtranRelation=GRY502C_GRY502A selectionPriority 19 2007-05-24 04:05:23 MO-C CRE RncFunction=1,UtranCell=GRY502C,Fach=1 2007-05-24 04:05:33 MO-C SET RncFunction=1,UtranCell=GRY502C,Fach=1 userLabel 2007-05-24 04:05:34 MO-C CRE RncFunction=1,UtranCell=GRY502C,GsmRelation=GRY502C_ZRY502C 2007-05-24 04:05:35 MO-C SET RncFunction=1,UtranCell=GRY502C,GsmRelation=GRY502C_ZRY502C selectionPriority 8 2007-05-24 04:05:38 MO-C CRE RncFunction=1,UtranCell=GRY502C,GsmRelation=GRY502C_ZRY502B 2007-05-24 04:05:40 MO-C SET RncFunction=1,UtranCell=GRY502C,GsmRelation=GRY502C_ZRY502B selectionPriority 7 2007-05-24 04:05:42 MO-C CRE RncFunction=1,UtranCell=GRY502C,GsmRelation=GRY502C_ZRY502A 2007-05-24 04:05:45 MO-C SET RncFunction=1,UtranCell=GRY502C,GsmRelation=GRY502C_ZRY502A selectionPriority 6 2007-05-24 04:05:45 MO-C CRE RncFunction=1,UtranCell=GRY502C,Rach=1 2007-05-24 04:05:52 MO-C SET RncFunction=1,UtranCell=GRY502C,Rach=1 userLabel 2007-05-24 04:06:02 MO-C CRE RncFunction=1,UtranCell=GRY502C,UtranRelation=GRY502C_GRY445C 2007-05-24 04:06:04 MO-C SET RncFunction=1,UtranCell=GRY502C,UtranRelation=GRY502C_GRY445C selectionPriority 12 2007-05-24 04:06:07 MO-C CRE RncFunction=1,UtranCell=GRY502C,UtranRelation=GRY502C_GRY445B 2007-05-24 04:06:08 MO-C SET RncFunction=1,UtranCell=GRY502C,UtranRelation=GRY502C_GRY445B selectionPriority 11 2007-05-24 04:06:12 MO-C CRE RncFunction=1,UtranCell=GRY502C,UtranRelation=GRY502C_GRY723B 2007-05-24 04:06:14 MO-C SET RncFunction=1,UtranCell=GRY502C,UtranRelation=GRY502C_GRY723B selectionPriority 15 2007-05-24 04:06:17 MO-C CRE RncFunction=1,UtranCell=GRY502C,GsmRelation=GRY502C_ZRY445C 2007-05-24 04:06:18 MO-C SET RncFunction=1,UtranCell=GRY502C,GsmRelation=GRY502C_ZRY445C selectionPriority 5 2007-05-24 04:06:20 MO-C CRE RncFunction=1,UtranCell=GRY502C,GsmRelation=GRY502C_COW617B 2007-05-24 04:06:22 MO-C SET RncFunction=1,UtranCell=GRY502C,GsmRelation=GRY502C_COW617B selectionPriority 1 2007-05-24 04:06:25 MO-C CRE RncFunction=1,UtranCell=GRY502C,Hsdsch=1 2007-05-24 04:06:26 MO-C SET RncFunction=1,UtranCell=GRY502C,Hsdsch=1 deltaNack1 5 2007-05-24 04:06:27 MO-C SET RncFunction=1,UtranCell=GRY502C,Hsdsch=1 deltaNack2 7 2007-05-24 04:06:28 MO-C SET RncFunction=1,UtranCell=GRY502C,Hsdsch=1 administrativeState 1 2007-05-24 04:06:31 MO-C SET RncFunction=1,UtranCell=GRY502C,Hsdsch=1 deltaCqi2 6 2007-05-24 04:06:34 MO-C SET RncFunction=1,UtranCell=GRY502C,Hsdsch=1 userLabel 2007-05-24 04:06:36 MO-C SET RncFunction=1,UtranCell=GRY502C,Hsdsch=1 deltaAck1 5 2007-05-24 04:06:37 MO-C SET RncFunction=1,UtranCell=GRY502C,Hsdsch=1 deltaAck2 7 2007-05-24 04:06:38 MO-C CRE RncFunction=1,UtranCell=GRY502C,UtranRelation=GRY502C_GCW617B 2007-05-24 04:06:40 MO-C SET RncFunction=1,UtranCell=GRY502C,UtranRelation=GRY502C_GCW617B selectionPriority 18

2007-05-24 04:06:43 MO-C CRE RncFunction=1,UtranCell=GRY502C,UtranRelation=GRY502C_GCW617A 2007-05-24 04:06:47 MO-C SET RncFunction=1,UtranCell=GRY502C,UtranRelation=GRY502C_GCW617A selectionPriority 17 2007-05-24 04:06:48 MO-C CRE RncFunction=1,UtranCell=GRY502C,UtranRelation=GRY502C_GRY065C 2007-05-24 04:06:51 MO-C SET RncFunction=1,UtranCell=GRY502C,UtranRelation=GRY502C_GRY065C selectionPriority 8 2007-05-24 04:06:53 MO-C CRE RncFunction=1,UtranCell=GRY502C,UtranRelation=GRY502C_GRY065B 2007-05-24 04:06:55 MO-C SET RncFunction=1,UtranCell=GRY502C,UtranRelation=GRY502C_GRY065B selectionPriority 7 2007-05-24 04:06:58 MO-C CRE RncFunction=1,UtranCell=GRY502C,UtranRelation=GRY502C_GRY065A 2007-05-24 04:06:59 MO-C SET RncFunction=1,UtranCell=GRY502C,UtranRelation=GRY502C_GRY065A selectionPriority 6 2007-05-24 04:07:03 MO-C CRE RncFunction=1,UtranCell=GRY502C,UtranRelation=GRY502C_GRY062C 2007-05-24 04:07:06 MO-C SET RncFunction=1,UtranCell=GRY502C,UtranRelation=GRY502C_GRY062C selectionPriority 5 2007-05-24 04:07:08 MO-C CRE RncFunction=1,UtranCell=GRY502C,UtranRelation=GRY502C_GRY041A 2007-05-24 04:07:11 MO-C SET RncFunction=1,UtranCell=GRY502C,UtranRelation=GRY502C_GRY041A selectionPriority 4 2007-05-24 04:07:14 MO-C CRE RncFunction=1,UtranCell=GRY502C,UtranRelation=GRY502C_GRY363C 2007-05-24 04:07:18 MO-C SET RncFunction=1,UtranCell=GRY502C,UtranRelation=GRY502C_GRY363C selectionPriority 10 2007-05-24 04:07:19 MO-C CRE RncFunction=1,UtranCell=GRY502C,UtranRelation=GRY502C_GRY363A 2007-05-24 04:07:21 MO-C SET RncFunction=1,UtranCell=GRY502C,UtranRelation=GRY502C_GRY363A selectionPriority 9 2007-05-24 04:07:24 MO-C CRE RncFunction=1,UtranCell=GRY502C,UtranRelation=GRY502C_GRY657B 2007-05-24 04:07:26 MO-C SET RncFunction=1,UtranCell=GRY502C,UtranRelation=GRY502C_GRY657B selectionPriority 22 2007-05-24 04:07:28 MO-C CRE RncFunction=1,UtranCell=GRY502C,UtranRelation=GRY502C_GRY657A 2007-05-24 04:07:31 MO-C SET RncFunction=1,UtranCell=GRY502C,UtranRelation=GRY502C_GRY657A selectionPriority 21 2007-05-24 04:07:33 MO-C CRE RncFunction=1,UtranCell=GRY502C,UtranRelation=GRY502C_GRY647C 2007-05-24 04:07:38 MO-C SET RncFunction=1,UtranCell=GRY502C,UtranRelation=GRY502C_GRY647C selectionPriority 14 2007-05-24 04:07:38 MO-C CRE RncFunction=1,UtranCell=GRY502C,UtranRelation=GRY502C_GRY647B 2007-05-24 04:07:39 MO-C SET RncFunction=1,UtranCell=GRY502C,UtranRelation=GRY502C_GRY647B selectionPriority 13 2007-05-24 04:07:43 MO-C CRE RncFunction=1,UtranCell=GRY502C,GsmRelation=GRY502C_ZRY065B 2007-05-24 04:07:44 MO-C SET RncFunction=1,UtranCell=GRY502C,GsmRelation=GRY502C_ZRY065B selectionPriority 4 2007-05-24 04:07:46 MO-C CRE RncFunction=1,UtranCell=GRY502C,GsmRelation=GRY502C_ZRY065A 2007-05-24 04:07:49 MO-C SET RncFunction=1,UtranCell=GRY502C,GsmRelation=GRY502C_ZRY065A selectionPriority 3 2007-05-24 04:07:50 MO-C CRE RncFunction=1,UtranCell=GRY502B,GsmRelation=GRY502B_ZRY363C 2007-05-24 04:07:51 MO-C SET RncFunction=1,UtranCell=GRY502B,GsmRelation=GRY502B_ZRY363C selectionPriority 4 2007-05-24 04:07:54 MO-C CRE RncFunction=1,UtranCell=GRY502B,GsmRelation=GRY502B_ZRY363B 2007-05-24 04:07:57 MO-C SET RncFunction=1,UtranCell=GRY502B,GsmRelation=GRY502B_ZRY363B selectionPriority 3

2007-05-24 04:07:57 MO-C CRE RncFunction=1,UtranCell=GRY502B,Pch=1 2007-05-24 04:08:03 MO-C SET RncFunction=1,UtranCell=GRY502B,Pch=1 userLabel 2007-05-24 04:08:04 MO-C CRE RncFunction=1,UtranCell=GRY502B,Fach=1 2007-05-24 04:08:05 MO-C SET RncFunction=1,UtranCell=GRY502B,Fach=1 userLabel 2007-05-24 04:08:14 MO-C CRE RncFunction=1,UtranCell=GRY502B,UtranRelation=GRY502B_GRY536C 2007-05-24 04:08:18 MO-C SET RncFunction=1,UtranCell=GRY502B,UtranRelation=GRY502B_GRY536C selectionPriority 15 2007-05-24 04:08:19 MO-C CRE RncFunction=1,UtranCell=GRY502B,UtranRelation=GRY502B_GRY536A 2007-05-24 04:08:21 MO-C SET RncFunction=1,UtranCell=GRY502B,UtranRelation=GRY502B_GRY536A selectionPriority 14 2007-05-24 04:08:24 MO-C CRE RncFunction=1,UtranCell=GRY502B,Hsdsch=1 2007-05-24 04:08:26 MO-C SET RncFunction=1,UtranCell=GRY502B,Hsdsch=1 administrativeState 1 2007-05-24 04:08:28 MO-C SET RncFunction=1,UtranCell=GRY502B,Hsdsch=1 deltaCqi2 6 2007-05-24 04:08:31 MO-C SET RncFunction=1,UtranCell=GRY502B,Hsdsch=1 userLabel 2007-05-24 04:08:32 MO-C SET RncFunction=1,UtranCell=GRY502B,Hsdsch=1 deltaAck1 5 2007-05-24 04:08:34 MO-C SET RncFunction=1,UtranCell=GRY502B,Hsdsch=1 deltaAck2 7 2007-05-24 04:08:35 MO-C SET RncFunction=1,UtranCell=GRY502B,Hsdsch=1 deltaNack1 5 2007-05-24 04:08:36 MO-C SET RncFunction=1,UtranCell=GRY502B,Hsdsch=1 deltaNack2 7 2007-05-24 04:08:37 MO-C CRE RncFunction=1,UtranCell=GRY502B,UtranRelation=GRY502B_GRY849A 2007-05-24 04:08:42 MO-C CRE RncFunction=1,UtranCell=GRY502B,UtranRelation=GRY502B_GRY502C 2007-05-24 04:08:46 MO-C SET RncFunction=1,UtranCell=GRY502B,UtranRelation=GRY502B_GRY502C selectionPriority 22 2007-05-24 04:08:47 MO-C CRE RncFunction=1,UtranCell=GRY502B,UtranRelation=GRY502B_GRY502A 2007-05-24 04:08:49 MO-C SET RncFunction=1,UtranCell=GRY502B,UtranRelation=GRY502B_GRY502A selectionPriority 21 2007-05-24 04:08:52 MO-C CRE RncFunction=1,UtranCell=GRY502B,GsmRelation=GRY502B_URY502B 2007-05-24 04:08:54 MO-C SET RncFunction=1,UtranCell=GRY502B,GsmRelation=GRY502B_URY502B selectionPriority 2 2007-05-24 04:08:56 MO-C CRE RncFunction=1,UtranCell=GRY502B,Rach=1 2007-05-24 04:09:03 MO-C SET RncFunction=1,UtranCell=GRY502B,Rach=1 userLabel 2007-05-24 04:09:11 MO-C CRE RncFunction=1,UtranCell=GRY502B,GsmRelation=GRY502B_ZRY570C 2007-05-24 04:09:13 MO-C SET RncFunction=1,UtranCell=GRY502B,GsmRelation=GRY502B_ZRY570C selectionPriority 7 2007-05-24 04:09:15 MO-C CRE RncFunction=1,UtranCell=GRY502B,GsmRelation=GRY502B_ZRY570B 2007-05-24 04:09:19 MO-C SET RncFunction=1,UtranCell=GRY502B,GsmRelation=GRY502B_ZRY570B selectionPriority 6 2007-05-24 04:09:19 MO-C CRE RncFunction=1,UtranCell=GRY502B,UtranRelation=GRY502B_GRY445B 2007-05-24 04:09:24 MO-C SET RncFunction=1,UtranCell=GRY502B,UtranRelation=GRY502B_GRY445B selectionPriority 13 2007-05-24 04:09:24 MO-C CRE RncFunction=1,UtranCell=GRY502B,GsmRelation=GRY502B_ZRY502B 2007-05-24 04:09:25 MO-C SET RncFunction=1,UtranCell=GRY502B,GsmRelation=GRY502B_ZRY502B selectionPriority 5 2007-05-24 04:09:27 MO-C CRE RncFunction=1,UtranCell=GRY502B,UtranRelation=GRY502B_GCW617B 2007-05-24 04:09:29 MO-C SET RncFunction=1,UtranCell=GRY502B,UtranRelation=GRY502B_GCW617B selectionPriority 20 2007-05-24 04:09:32 MO-C CRE RncFunction=1,UtranCell=GRY502B,UtranRelation=GRY502B_GCW617A 2007-05-24 04:09:35 MO-C SET RncFunction=1,UtranCell=GRY502B,UtranRelation=GRY502B_GCW617A selectionPriority 19 2007-05-24 04:09:36 MO-C CRE RncFunction=1,UtranCell=GRY502B,UtranRelation=GRY502B_GRY393A

2007-05-24 04:09:39 MO-C SET RncFunction=1,UtranCell=GRY502B,UtranRelation=GRY502B_GRY393A selectionPriority 12 2007-05-24 04:09:41 MO-C CRE RncFunction=1,UtranCell=GRY502B,UtranRelation=GRY502B_GRY065B 2007-05-24 04:09:44 MO-C SET RncFunction=1,UtranCell=GRY502B,UtranRelation=GRY502B_GRY065B selectionPriority 8 2007-05-24 04:09:46 MO-C CRE RncFunction=1,UtranCell=GRY502B,UtranRelation=GRY502B_GRY062C 2007-05-24 04:09:48 MO-C SET RncFunction=1,UtranCell=GRY502B,UtranRelation=GRY502B_GRY062C selectionPriority 7 2007-05-24 04:09:50 MO-C CRE RncFunction=1,UtranCell=GRY502B,UtranRelation=GRY502B_GRY062B 2007-05-24 04:09:53 MO-C SET RncFunction=1,UtranCell=GRY502B,UtranRelation=GRY502B_GRY062B selectionPriority 6 2007-05-24 04:09:55 MO-C CRE RncFunction=1,UtranCell=GRY502B,UtranRelation=GRY502B_GRY062A 2007-05-24 04:09:56 MO-C SET RncFunction=1,UtranCell=GRY502B,UtranRelation=GRY502B_GRY062A selectionPriority 5 2007-05-24 04:09:59 MO-C CRE RncFunction=1,UtranCell=GRY502B,UtranRelation=GRY502B_GRY363C 2007-05-24 04:10:00 MO-C SET RncFunction=1,UtranCell=GRY502B,UtranRelation=GRY502B_GRY363C selectionPriority 11 2007-05-24 04:10:04 MO-C CRE RncFunction=1,UtranCell=GRY502B,UtranRelation=GRY502B_GRY363B 2007-05-24 04:10:08 MO-C SET RncFunction=1,UtranCell=GRY502B,UtranRelation=GRY502B_GRY363B selectionPriority 10 2007-05-24 04:10:08 MO-C CRE RncFunction=1,UtranCell=GRY502B,UtranRelation=GRY502B_GRY363A 2007-05-24 04:10:12 MO-C SET RncFunction=1,UtranCell=GRY502B,UtranRelation=GRY502B_GRY363A selectionPriority 9 2007-05-24 04:10:13 MO-C CRE RncFunction=1,UtranCell=GRY502B,UtranRelation=GRY502B_GRY913C 2007-05-24 04:10:14 MO-C SET RncFunction=1,UtranCell=GRY502B,UtranRelation=GRY502B_GRY913C selectionPriority 18 2007-05-24 04:10:17 MO-C CRE RncFunction=1,UtranCell=GRY502B,UtranRelation=GRY502B_GRY913A 2007-05-24 04:10:19 MO-C SET RncFunction=1,UtranCell=GRY502B,UtranRelation=GRY502B_GRY913A selectionPriority 17 2007-05-24 04:10:22 MO-C CRE RncFunction=1,UtranCell=GRY502B,GsmRelation=GRY502B_COW617A 2007-05-24 04:10:25 MO-C SET RncFunction=1,UtranCell=GRY502B,GsmRelation=GRY502B_COW617A selectionPriority 1 2007-05-24 04:10:26 MO-C CRE RncFunction=1,UtranCell=GRY502A,UtranRelation=GRY502A_GRY913A 2007-05-24 04:10:32 MO-C SET RncFunction=1,UtranCell=GRY502A,UtranRelation=GRY502A_GRY913A selectionPriority 18 2007-05-24 04:10:33 MO-C CRE RncFunction=1,UtranCell=GRY502A,Fach=1 2007-05-24 04:10:36 MO-C SET RncFunction=1,UtranCell=GRY502A,Fach=1 userLabel 2007-05-24 04:10:46 MO-C CRE RncFunction=1,UtranCell=GRY502A,GsmRelation=GRY502A_ZRY445C 2007-05-24 04:10:49 MO-C SET RncFunction=1,UtranCell=GRY502A,GsmRelation=GRY502A_ZRY445C selectionPriority 9 2007-05-24 04:10:51 MO-C CRE RncFunction=1,UtranCell=GRY502A,GsmRelation=GRY502A_ZRY445B 2007-05-24 04:10:54 MO-C SET RncFunction=1,UtranCell=GRY502A,GsmRelation=GRY502A_ZRY445B selectionPriority 8 2007-05-24 04:10:55 MO-C CRE RncFunction=1,UtranCell=GRY502A,GsmRelation=GRY502A_ZRY445A 2007-05-24 04:10:57 MO-C SET RncFunction=1,UtranCell=GRY502A,GsmRelation=GRY502A_ZRY445A selectionPriority 7 2007-05-24 04:10:58 MO-C CRE RncFunction=1,UtranCell=GRY502A,UtranRelation=GRY502A_GRI002B 2007-05-24 04:11:01 MO-C SET RncFunction=1,UtranCell=GRY502A,UtranRelation=GRY502A_GRI002B selectionPriority 3

2007-05-24 04:11:03 MO-C CRE RncFunction=1,UtranCell=GRY502A,GsmRelation=GRY502A_COW617B 2007-05-24 04:11:05 MO-C SET RncFunction=1,UtranCell=GRY502A,GsmRelation=GRY502A_COW617B selectionPriority 1 2007-05-24 04:11:06 MO-C CRE RncFunction=1,UtranCell=GRY502A,GsmRelation=GRY502A_ZRY402C 2007-05-24 04:11:08 MO-C SET RncFunction=1,UtranCell=GRY502A,GsmRelation=GRY502A_ZRY402C selectionPriority 6 2007-05-24 04:11:10 MO-C CRE RncFunction=1,UtranCell=GRY502A,GsmRelation=GRY502A_ZRY402A 2007-05-24 04:11:13 MO-C SET RncFunction=1,UtranCell=GRY502A,GsmRelation=GRY502A_ZRY402A selectionPriority 5 2007-05-24 04:11:13 MO-C CRE RncFunction=1,UtranCell=GRY502A,UtranRelation=GRY502A_GRY843B 2007-05-24 04:11:17 MO-C SET RncFunction=1,UtranCell=GRY502A,UtranRelation=GRY502A_GRY843B selectionPriority 17 2007-05-24 04:11:18 MO-C CRE RncFunction=1,UtranCell=GRY502A,UtranRelation=GRY502A_GRY502C 2007-05-24 04:11:20 MO-C SET RncFunction=1,UtranCell=GRY502A,UtranRelation=GRY502A_GRY502C selectionPriority 23 2007-05-24 04:11:23 MO-C CRE RncFunction=1,UtranCell=GRY502A,UtranRelation=GRY502A_GRY502B 2007-05-24 04:11:26 MO-C SET RncFunction=1,UtranCell=GRY502A,UtranRelation=GRY502A_GRY502B selectionPriority 22 2007-05-24 04:11:27 MO-C CRE RncFunction=1,UtranCell=GRY502A,Rach=1 2007-05-24 04:11:32 MO-C SET RncFunction=1,UtranCell=GRY502A,Rach=1 userLabel 2007-05-24 04:11:42 MO-C CRE RncFunction=1,UtranCell=GRY502A,Pch=1 2007-05-24 04:11:46 MO-C SET RncFunction=1,UtranCell=GRY502A,Pch=1 userLabel 2007-05-24 04:11:49 MO-C CRE RncFunction=1,UtranCell=GRY502A,GsmRelation=GRY502A_ZRY010C 2007-05-24 04:11:52 MO-C SET RncFunction=1,UtranCell=GRY502A,GsmRelation=GRY502A_ZRY010C selectionPriority 4 2007-05-24 04:11:52 MO-C CRE RncFunction=1,UtranCell=GRY502A,GsmRelation=GRY502A_ZRY010A 2007-05-24 04:11:57 MO-C SET RncFunction=1,UtranCell=GRY502A,GsmRelation=GRY502A_ZRY010A selectionPriority 3 2007-05-24 04:11:57 MO-C CRE RncFunction=1,UtranCell=GRY502A,UtranRelation=GRY502A_GRY445C 2007-05-24 04:12:00 MO-C SET RncFunction=1,UtranCell=GRY502A,UtranRelation=GRY502A_GRY445C selectionPriority 12 2007-05-24 04:12:02 MO-C CRE RncFunction=1,UtranCell=GRY502A,UtranRelation=GRY502A_GRY445B 2007-05-24 04:12:05 MO-C SET RncFunction=1,UtranCell=GRY502A,UtranRelation=GRY502A_GRY445B selectionPriority 11 2007-05-24 04:12:06 MO-C CRE RncFunction=1,UtranCell=GRY502A,UtranRelation=GRY502A_GRY445A 2007-05-24 04:12:08 MO-C SET RncFunction=1,UtranCell=GRY502A,UtranRelation=GRY502A_GRY445A selectionPriority 10 2007-05-24 04:12:11 MO-C CRE RncFunction=1,UtranCell=GRY502A,UtranRelation=GRY502A_GRY744C 2007-05-24 04:12:17 MO-C SET RncFunction=1,UtranCell=GRY502A,UtranRelation=GRY502A_GRY744C selectionPriority 16 2007-05-24 04:12:17 MO-C CRE RncFunction=1,UtranCell=GRY502A,UtranRelation=GRY502A_GRY744B 2007-05-24 04:12:18 MO-C SET RncFunction=1,UtranCell=GRY502A,UtranRelation=GRY502A_GRY744B selectionPriority 15 2007-05-24 04:12:22 MO-C CRE RncFunction=1,UtranCell=GRY502A,GsmRelation=GRY502A_URY502A 2007-05-24 04:12:25 MO-C SET RncFunction=1,UtranCell=GRY502A,GsmRelation=GRY502A_URY502A selectionPriority 2 2007-05-24 04:12:26 MO-C CRE RncFunction=1,UtranCell=GRY502A,UtranRelation=GRY502A_GCW617B 2007-05-24 04:12:30 MO-C SET RncFunction=1,UtranCell=GRY502A,UtranRelation=GRY502A_GCW617B selectionPriority 21

2007-05-24 04:12:31 MO-C CRE RncFunction=1,UtranCell=GRY502A,UtranRelation=GRY502A_GCW617A 2007-05-24 04:12:34 MO-C SET RncFunction=1,UtranCell=GRY502A,UtranRelation=GRY502A_GCW617A selectionPriority 20 2007-05-24 04:12:36 MO-C CRE RncFunction=1,UtranCell=GRY502A,UtranRelation=GRY502A_GRY065B 2007-05-24 04:12:38 MO-C SET RncFunction=1,UtranCell=GRY502A,UtranRelation=GRY502A_GRY065B selectionPriority 7 2007-05-24 04:12:40 MO-C CRE RncFunction=1,UtranCell=GRY502A,UtranRelation=GRY502A_GRY065A 2007-05-24 04:12:45 MO-C SET RncFunction=1,UtranCell=GRY502A,UtranRelation=GRY502A_GRY065A selectionPriority 6 2007-05-24 04:12:45 MO-C CRE RncFunction=1,UtranCell=GRY502A,UtranRelation=GRY502A_GRY062C 2007-05-24 04:12:46 MO-C SET RncFunction=1,UtranCell=GRY502A,UtranRelation=GRY502A_GRY062C selectionPriority 5 2007-05-24 04:12:49 MO-C CRE RncFunction=1,UtranCell=GRY502A,UtranRelation=GRY502A_GRY062A 2007-05-24 04:12:54 MO-C SET RncFunction=1,UtranCell=GRY502A,UtranRelation=GRY502A_GRY062A selectionPriority 4 2007-05-24 04:12:54 MO-C CRE RncFunction=1,UtranCell=GRY502A,UtranRelation=GRY502A_GRY363C 2007-05-24 04:12:56 MO-C SET RncFunction=1,UtranCell=GRY502A,UtranRelation=GRY502A_GRY363C selectionPriority 9 2007-05-24 04:12:59 MO-C CRE RncFunction=1,UtranCell=GRY502A,UtranRelation=GRY502A_GRY363A 2007-05-24 04:13:02 MO-C SET RncFunction=1,UtranCell=GRY502A,UtranRelation=GRY502A_GRY363A selectionPriority 8 2007-05-24 04:13:04 MO-C CRE RncFunction=1,UtranCell=GRY502A,Hsdsch=1 2007-05-24 04:13:08 MO-C SET RncFunction=1,UtranCell=GRY502A,Hsdsch=1 userLabel 2007-05-24 04:13:09 MO-C SET RncFunction=1,UtranCell=GRY502A,Hsdsch=1 administrativeState 1 2007-05-24 04:13:11 MO-C SET RncFunction=1,UtranCell=GRY502A,Hsdsch=1 deltaAck1 5 2007-05-24 04:13:12 MO-C SET RncFunction=1,UtranCell=GRY502A,Hsdsch=1 deltaAck2 7 2007-05-24 04:13:13 MO-C SET RncFunction=1,UtranCell=GRY502A,Hsdsch=1 deltaNack1 5 2007-05-24 04:13:15 MO-C SET RncFunction=1,UtranCell=GRY502A,Hsdsch=1 deltaNack2 7 2007-05-24 04:13:18 MO-C SET RncFunction=1,UtranCell=GRY502A,Hsdsch=1 deltaCqi2 6 2007-05-24 04:13:18 MO-C CRE RncFunction=1,UtranCell=GRY502A,UtranRelation=GRY502A_GRY647C 2007-05-24 04:13:21 MO-C SET RncFunction=1,UtranCell=GRY502A,UtranRelation=GRY502A_GRY647C selectionPriority 14 2007-05-24 04:13:23 MO-C CRE RncFunction=1,UtranCell=GRY502A,UtranRelation=GRY502A_GRY647B 2007-05-24 04:13:27 MO-C SET RncFunction=1,UtranCell=GRY502A,UtranRelation=GRY502A_GRY647B selectionPriority 13 2007-05-24 04:13:28 MO-C CRE RncFunction=1,UtranCell=GRY502A,UtranRelation=GRY502A_GRY965C 2007-05-24 04:13:30 MO-C SET RncFunction=1,UtranCell=GRY502A,UtranRelation=GRY502A_GRY965C selectionPriority 19 2007-05-24 04:13:33 MO-C CRE RncFunction=1,UtranCell=GRY502A,GsmRelation=GRY502A_ZRY502A 2007-05-24 04:13:36 MO-C CRE RncFunction=1,IubLink=Iub_GRY502,NodeSynchTp=2 2007-05-24 04:13:38 MO-C SET RncFunction=1,IubLink=Iub_GRY502,NodeSynchTp=2 userLabel 2 2007-05-24 04:13:39 MO-C SET RncFunction=1,IubLink=Iub_GRY502,NodeSynchTp=2 administrativeState 1 2007-05-24 04:13:39 MO-C CRE RncFunction=1,IubLink=Iub_GRY502,NodeSynchTp=1 2007-05-24 04:13:41 MO-C SET RncFunction=1,IubLink=Iub_GRY502,NodeSynchTp=1 administrativeState 1 2007-05-24 04:13:42 MO-C SET RncFunction=1,IubLink=Iub_GRY502,NodeSynchTp=1 userLabel 1 2007-05-24 04:13:42 MO-C CRE RncFunction=1,IubLink=Iub_GRY502,NbapDedicated=1 2007-05-24 04:13:44 MO-C SET RncFunction=1,IubLink=Iub_GRY502,NbapDedicated=1 administrativeState 1

2007-05-24 04:13:46 MO-C SET RncFunction=1,IubLink=Iub_GRY502,NbapDedicated=1 userLabel 1 2007-05-24 04:13:47 MO-C CRE RncFunction=1,IubLink=Iub_GRY502,NbapCommon=1 2007-05-24 04:13:48 MO-C SET RncFunction=1,IubLink=Iub_GRY502,NbapCommon=1 userLabel 1 2007-05-24 04:13:50 MO-C SET RncFunction=1,IubLink=Iub_GRY502,NbapCommon=1 administrativeState 1 2007-05-24 04:13:51 MO-C CRE RncFunction=1,UtranCell=GCW617A,UtranRelation=GCW617A_GRY502C 2007-05-24 04:13:54 MO-C SET RncFunction=1,UtranCell=GCW617A,UtranRelation=GCW617A_GRY502C selectionPriority 13 2007-05-24 04:13:57 MO-C CRE RncFunction=1,UtranCell=GCW617A,UtranRelation=GCW617A_GRY502B 2007-05-24 04:14:01 MO-C SET RncFunction=1,UtranCell=GCW617A,UtranRelation=GCW617A_GRY502B selectionPriority 12 2007-05-24 04:14:03 MO-C CRE RncFunction=1,UtranCell=GCW617A,UtranRelation=GCW617A_GRY502A 2007-05-24 04:14:06 MO-C SET RncFunction=1,UtranCell=GCW617A,UtranRelation=GCW617A_GRY502A selectionPriority 11 2007-05-24 04:14:08 MO-C CRE RncFunction=1,UtranCell=GCW617B,UtranRelation=GCW617B_GRY502C 2007-05-24 04:14:12 MO-C SET RncFunction=1,UtranCell=GCW617B,UtranRelation=GCW617B_GRY502C selectionPriority 13 2007-05-24 04:14:14 MO-C CRE RncFunction=1,UtranCell=GCW617B,UtranRelation=GCW617B_GRY502B 2007-05-24 04:14:16 MO-C SET RncFunction=1,UtranCell=GCW617B,UtranRelation=GCW617B_GRY502B selectionPriority 12 2007-05-24 04:14:19 MO-C CRE RncFunction=1,UtranCell=GCW617B,UtranRelation=GCW617B_GRY502A 2007-05-24 04:14:21 MO-C SET RncFunction=1,UtranCell=GCW617B,UtranRelation=GCW617B_GRY502A selectionPriority 11 2007-05-24 04:14:26 MO-C CRE RncFunction=1,UtranCell=GRY723B,UtranRelation=GRY723B_GRY502C 2007-05-24 04:14:31 MO-C SET RncFunction=1,UtranCell=GRY723B,UtranRelation=GRY723B_GRY502C selectionPriority 28 2007-05-24 04:14:31 MO-C CRE RncFunction=1,UtranCell=GRY744B,UtranRelation=GRY744B_GRY502A 2007-05-24 04:14:37 MO-C CRE RncFunction=1,UtranCell=GRY744C,UtranRelation=GRY744C_GRY502A 2007-05-24 04:14:42 MO-C CRE RncFunction=1,UtranCell=GRY445A,UtranRelation=GRY445A_GRY502A 2007-05-24 04:14:48 MO-C CRE RncFunction=1,UtranCell=GRY445B,UtranRelation=GRY445B_GRY502C 2007-05-24 04:14:51 MO-C SET RncFunction=1,UtranCell=GRY445B,UtranRelation=GRY445B_GRY502C selectionPriority 33 2007-05-24 04:14:54 MO-C CRE RncFunction=1,UtranCell=GRY445B,UtranRelation=GRY445B_GRY502B 2007-05-24 04:14:59 MO-C SET RncFunction=1,UtranCell=GRY445B,UtranRelation=GRY445B_GRY502B selectionPriority 32 2007-05-24 04:15:00 MO-C CRE RncFunction=1,UtranCell=GRY445B,UtranRelation=GRY445B_GRY502A 2007-05-24 04:15:03 MO-C SET RncFunction=1,UtranCell=GRY445B,UtranRelation=GRY445B_GRY502A selectionPriority 31 2007-05-24 04:15:07 MO-C CRE RncFunction=1,UtranCell=GRY445C,UtranRelation=GRY445C_GRY502C 2007-05-24 04:15:11 MO-C SET RncFunction=1,UtranCell=GRY445C,UtranRelation=GRY445C_GRY502C selectionPriority 35 2007-05-24 04:15:13 MO-C CRE RncFunction=1,UtranCell=GRY445C,UtranRelation=GRY445C_GRY502A 2007-05-24 04:15:16 MO-C SET RncFunction=1,UtranCell=GRY445C,UtranRelation=GRY445C_GRY502A selectionPriority 34 2007-05-24 04:15:20 MO-C CRE RncFunction=1,UtranCell=GRY843B,UtranRelation=GRY843B_GRY502A

2007-05-24 04:15:28 MO-C CRE RncFunction=1,UtranCell=GRY849A,UtranRelation=GRY849A_GRY502C 2007-05-24 04:15:34 MO-C SET RncFunction=1,UtranCell=GRY849A,UtranRelation=GRY849A_GRY502C selectionPriority 22 2007-05-24 04:15:35 MO-C CRE RncFunction=1,UtranCell=GRY849A,UtranRelation=GRY849A_GRY502B 2007-05-24 04:15:39 MO-C SET RncFunction=1,UtranCell=GRY849A,UtranRelation=GRY849A_GRY502B selectionPriority 21 2007-05-24 04:15:42 MO-C CRE RncFunction=1,UtranCell=GRY536A,UtranRelation=GRY536A_GRY502B 2007-05-24 04:15:48 MO-C SET RncFunction=1,UtranCell=GRY536A,UtranRelation=GRY536A_GRY502B selectionPriority 23 2007-05-24 04:15:48 MO-C CRE RncFunction=1,UtranCell=GRY536C,UtranRelation=GRY536C_GRY502B 2007-05-24 04:15:54 MO-C CRE RncFunction=1,UtranCell=GRI002B,UtranRelation=GRI002B_GRY502A 2007-05-24 04:15:58 MO-C SET RncFunction=1,UtranCell=GRI002B,UtranRelation=GRI002B_GRY502A selectionPriority 22 2007-05-24 04:15:59 MO-C CRE RncFunction=1,UtranCell=GRY913A,UtranRelation=GRY913A_GRY502B 2007-05-24 04:16:04 MO-C SET RncFunction=1,UtranCell=GRY913A,UtranRelation=GRY913A_GRY502B selectionPriority 33 2007-05-24 04:16:04 MO-C CRE RncFunction=1,UtranCell=GRY913A,UtranRelation=GRY913A_GRY502A 2007-05-24 04:16:07 MO-C SET RncFunction=1,UtranCell=GRY913A,UtranRelation=GRY913A_GRY502A selectionPriority 32 2007-05-24 04:16:09 MO-C CRE RncFunction=1,UtranCell=GRY913C,UtranRelation=GRY913C_GRY502B 2007-05-24 04:16:14 MO-C SET RncFunction=1,UtranCell=GRY913C,UtranRelation=GRY913C_GRY502B selectionPriority 26 2007-05-24 04:16:15 MO-C CRE RncFunction=1,UtranCell=GRY965C,UtranRelation=GRY965C_GRY502A 2007-05-24 04:16:20 MO-C CRE RncFunction=1,UtranCell=GRY647B,UtranRelation=GRY647B_GRY502C 2007-05-24 04:16:24 MO-C SET RncFunction=1,UtranCell=GRY647B,UtranRelation=GRY647B_GRY502C selectionPriority 33 2007-05-24 04:16:25 MO-C CRE RncFunction=1,UtranCell=GRY647B,UtranRelation=GRY647B_GRY502A 2007-05-24 04:16:27 MO-C SET RncFunction=1,UtranCell=GRY647B,UtranRelation=GRY647B_GRY502A selectionPriority 32 2007-05-24 04:16:29 MO-C CRE RncFunction=1,UtranCell=GRY647C,UtranRelation=GRY647C_GRY502C 2007-05-24 04:16:30 MO-C SET RncFunction=1,UtranCell=GRY647C,UtranRelation=GRY647C_GRY502C selectionPriority 26 2007-05-24 04:16:34 MO-C CRE RncFunction=1,UtranCell=GRY647C,UtranRelation=GRY647C_GRY502A 2007-05-24 04:16:35 MO-C SET RncFunction=1,UtranCell=GRY647C,UtranRelation=GRY647C_GRY502A selectionPriority 25 2007-05-24 04:16:39 MO-C CRE RncFunction=1,UtranCell=GRY657A,UtranRelation=GRY657A_GRY502C 2007-05-24 04:16:43 MO-C CRE RncFunction=1,UtranCell=GRY657B,UtranRelation=GRY657B_GRY502C 2007-05-24 04:16:48 MO-C SET RncFunction=1,UtranCell=GRY657B,UtranRelation=GRY657B_GRY502C selectionPriority 23 2007-05-24 04:16:48 MO-C CRE RncFunction=1,UtranCell=GRY363A,UtranRelation=GRY363A_GRY502C 2007-05-24 04:16:52 MO-C SET RncFunction=1,UtranCell=GRY363A,UtranRelation=GRY363A_GRY502C selectionPriority 29 2007-05-24 04:16:53 MO-C CRE RncFunction=1,UtranCell=GRY363A,UtranRelation=GRY363A_GRY502B 2007-05-24 04:16:55 MO-C SET RncFunction=1,UtranCell=GRY363A,UtranRelation=GRY363A_GRY502B selectionPriority 28 2007-05-24 04:16:58 MO-C CRE RncFunction=1,UtranCell=GRY363A,UtranRelation=GRY363A_GRY502A

2007-05-24 04:17:01 MO-C SET RncFunction=1,UtranCell=GRY363A,UtranRelation=GRY363A_GRY502A selectionPriority 27 2007-05-24 04:17:03 MO-C CRE RncFunction=1,UtranCell=GRY363B,UtranRelation=GRY363B_GRY502B 2007-05-24 04:17:05 MO-C SET RncFunction=1,UtranCell=GRY363B,UtranRelation=GRY363B_GRY502B selectionPriority 21 2007-05-24 04:17:08 MO-C CRE RncFunction=1,UtranCell=GRY363C,UtranRelation=GRY363C_GRY502C 2007-05-24 04:17:13 MO-C SET RncFunction=1,UtranCell=GRY363C,UtranRelation=GRY363C_GRY502C selectionPriority 39 2007-05-24 04:17:13 MO-C CRE RncFunction=1,UtranCell=GRY363C,UtranRelation=GRY363C_GRY502B 2007-05-24 04:17:15 MO-C SET RncFunction=1,UtranCell=GRY363C,UtranRelation=GRY363C_GRY502B selectionPriority 38 2007-05-24 04:17:18 MO-C CRE RncFunction=1,UtranCell=GRY363C,UtranRelation=GRY363C_GRY502A 2007-05-24 04:17:22 MO-C SET RncFunction=1,UtranCell=GRY363C,UtranRelation=GRY363C_GRY502A selectionPriority 37 2007-05-24 04:17:23 MO-C CRE RncFunction=1,UtranCell=GRY041A,UtranRelation=GRY041A_GRY502C 2007-05-24 04:17:27 MO-C SET RncFunction=1,UtranCell=GRY041A,UtranRelation=GRY041A_GRY502C selectionPriority 36 2007-05-24 04:17:28 MO-C CRE RncFunction=1,UtranCell=GRY062A,UtranRelation=GRY062A_GRY502B 2007-05-24 04:17:30 MO-C SET RncFunction=1,UtranCell=GRY062A,UtranRelation=GRY062A_GRY502B selectionPriority 35 2007-05-24 04:17:32 MO-C CRE RncFunction=1,UtranCell=GRY062A,UtranRelation=GRY062A_GRY502A 2007-05-24 04:17:36 MO-C SET RncFunction=1,UtranCell=GRY062A,UtranRelation=GRY062A_GRY502A selectionPriority 34 2007-05-24 04:17:37 MO-C CRE RncFunction=1,UtranCell=GRY062B,UtranRelation=GRY062B_GRY502B 2007-05-24 04:17:42 MO-C CRE RncFunction=1,UtranCell=GRY062C,UtranRelation=GRY062C_GRY502C 2007-05-24 04:17:45 MO-C SET RncFunction=1,UtranCell=GRY062C,UtranRelation=GRY062C_GRY502C selectionPriority 35 2007-05-24 04:17:47 MO-C CRE RncFunction=1,UtranCell=GRY062C,UtranRelation=GRY062C_GRY502B 2007-05-24 04:17:51 MO-C SET RncFunction=1,UtranCell=GRY062C,UtranRelation=GRY062C_GRY502B selectionPriority 34 2007-05-24 04:17:52 MO-C CRE RncFunction=1,UtranCell=GRY062C,UtranRelation=GRY062C_GRY502A 2007-05-24 04:17:56 MO-C SET RncFunction=1,UtranCell=GRY062C,UtranRelation=GRY062C_GRY502A selectionPriority 33 2007-05-24 04:17:57 MO-C CRE RncFunction=1,UtranCell=GRY065A,UtranRelation=GRY065A_GRY502C 2007-05-24 04:17:58 MO-C SET RncFunction=1,UtranCell=GRY065A,UtranRelation=GRY065A_GRY502C selectionPriority 29 2007-05-24 04:18:01 MO-C CRE RncFunction=1,UtranCell=GRY065A,UtranRelation=GRY065A_GRY502A 2007-05-24 04:18:02 MO-C SET RncFunction=1,UtranCell=GRY065A,UtranRelation=GRY065A_GRY502A selectionPriority 28 2007-05-24 04:18:06 MO-C CRE RncFunction=1,UtranCell=GRY065B,UtranRelation=GRY065B_GRY502C 2007-05-24 04:18:09 MO-C SET RncFunction=1,UtranCell=GRY065B,UtranRelation=GRY065B_GRY502C selectionPriority 25 2007-05-24 04:18:11 MO-C CRE RncFunction=1,UtranCell=GRY065B,UtranRelation=GRY065B_GRY502B 2007-05-24 04:18:14 MO-C SET RncFunction=1,UtranCell=GRY065B,UtranRelation=GRY065B_GRY502B selectionPriority 24 2007-05-24 04:18:15 MO-C CRE RncFunction=1,UtranCell=GRY065B,UtranRelation=GRY065B_GRY502A 2007-05-24 04:18:16 MO-C SET RncFunction=1,UtranCell=GRY065B,UtranRelation=GRY065B_GRY502A selectionPriority 23

2007-05-24 04:18:20 MO-C CRE RncFunction=1,UtranCell=GRY065C,UtranRelation=GRY065C_GRY502C 2007-05-24 04:18:23 MO-C SET RncFunction=1,UtranCell=GRY065C,UtranRelation=GRY065C_GRY502C selectionPriority 22 2007-05-24 04:18:24 MO-C CRE RncFunction=1,UtranCell=GRY393A,UtranRelation=GRY393A_GRY502B 2007-05-24 04:18:29 MO-C CRE TransportNetwork=1,Aal2RoutingCase=966101000100013

APPENDIX D: RAX CONGESTION RETURN /* GNNCC receive complain customer are unable to make calls in this site */ GRY272> lhsh 000800 te log read {RAX Slot=8} 070524-01:25:31 10.230.0.81 7.0 RESTRICTED RBS_NODE_MODEL_H_6_6 stopfile=/tmp/21415 $ lhsh 000800 te log read [1970-09-28 13:12:47.192] DEC_FrameManager ../dsp/sw/BackEnd/src/FrameManager.c:613 INFO:Paths to FDP are still busy (0x186 hi, 0x60DBF8F low) : 0xDEF8 [1970-09-28 13:12:47.196] DEC_FrameManager ../dsp/sw/BackEnd/src/FrameManager.c:613 INFO:Paths to FDP are still busy (0x186 hi, 0x60DBF8F low) : 0xDEF9 [1970-09-28 13:12:47.200] DEC_FrameManager ../dsp/sw/BackEnd/src/FrameManager.c:618 INFO:Pathfinder paths to DFP's not clear within 8 ms, will command FP cleanup anyway. : 0xDEFA [1970-09-28 13:12:47.200] DEC_PathFinderIntr ../dsp/sw/BackEnd/src/PathFinderIntr.c:139 INFO:ABN: Pathfinder error. Status reg hi=0x60386 low=0x61dbb8b : 0xDEFB [1970-09-28 13:12:47.200] DEC_UserManager ../dsp/sw/BackEnd/src/PathFinder.c:558 INFO:ABN: Congestion ceased, status reg hi=0x180 low=0x61dbf0f : 0xDEFC [1970-09-28 13:12:47.240] DEC_UserManager ../dsp/sw/BackEnd/src/PathFinder.c:573 INFO:ABN: Congestion, jobType=0, status reg hi=0x186 low=0x61dbf0f : 0xDEFD [1970-09-28 13:12:47.300] DEC_PathFinderIntr ../dsp/sw/BackEnd/src/PathFinderIntr.c:139 INFO:ABN: Pathfinder error. Status reg hi=0x1000186 low=0x61dbf0f : 0xDEFE [1970-09-28 13:12:47.300] DEC_PathFinderIntr ../dsp/sw/BackEnd/src/PathFinderIntr.c:144 INFO:ABN: FP watchdog expired : 0xDEFF [1970-09-28 13:12:47.360] DEC_FrameManager ../dsp/sw/BackEnd/src/FrameManager.c:613 INFO:Paths to FDP are still busy (0x186 hi, 0x61DBF0F low) : 0xDF00 [1970-09-28 13:12:47.364] DEC_FrameManager ../dsp/sw/BackEnd/src/FrameManager.c:613 INFO:Paths to FDP are still busy (0x186 hi, 0x60DBF0F low) : 0xDF01 [1970-09-28 13:12:47.368] DEC_FrameManager ../dsp/sw/BackEnd/src/FrameManager.c:618 INFO:Pathfinder paths to DFP's not clear within 8 ms, will command FP cleanup anyway. : 0xDF02 [1970-09-28 13:12:47.368] DEC_UserManager ../dsp/sw/BackEnd/src/PathFinder.c:558 INFO:ABN: Congestion ceased, status reg hi=0x184 low=0x61dbf0f : 0xDF03 [1970-09-28 13:12:47.408] DEC_UserManager ../dsp/sw/BackEnd/src/PathFinder.c:573 INFO:ABN: Congestion, jobType=0, status reg hi=0x186 low=0x61dbf0f : 0xDF04 $ GRY272> lhsh 000900 te log read {RAX Slot=9} [1970-09-27 23:23:55.568] DEC_PathFinderIntr ../dsp/sw/BackEnd/src/PathFinderIntr.c:144 INFO:ABN: FP watchdog expired : 0x1006 [1970-09-27 23:23:55.744] Cs_boardManager_proc osa_board_mgr.c:2305 INFO:Start of @(#)CXC1322250 R11CB02 2006-11-28 22:12:10 IST ac103dc3-0cff2362-2691 (dbm2_cs_basi) [1970-09-27 23:23:56.284] Sys_Spas_hwdrv_proc hwdrv.c:1093 INFO:SPAS_HWDRV Soft Initialized [1970-09-27 23:23:56.284] Sys_Spas_start_proc start.c:913 INFO:Warm restart of SPAS requested (ERI : Refresh) : spic warm, asccA warm, asccB not found. [1970-09-27 23:23:56.548] Sys_Spas_id_proc id.c:1974 INFO:APN is [9] [1970-09-27 23:23:56.548] Sys_Spas_plane_proc planechangecontrol.c:1700 INFO:SPAS_PCC: active Plane A

[1970-09-27 23:23:56.552] Sys_Spas_id_proc id.c:1661 INFO:SPAS resources found 1 SAI, 0 CORE, 0 ISL [1970-09-27 23:23:56.556] Sys_Spas_id_proc id.c:1778 INFO:Board type RAX revision R1C [1970-09-27 23:23:56.812] Sys_Spas_plane_proc asccconfiguration.c:463 INFO:SPAS_AC: asccA port is configured. [1970-09-27 23:23:59.668] Sys_Spas_id_proc id.c:1869 INFO:SMN is [0] [1970-09-27 23:23:59.880] Sys_Osa_Ntp_Manager_proc ntpstart.c:2634 INFO:NTP not synchronized [1970-09-27 23:23:59.880] Cls_lcim_proc lcim.c:316 INFO:LCIM: No CIM Pid received from NS (GetServicePidRequest), retrying [1970-09-27 23:24:06.356] Sys_Osa_clkDistr_proc systemclock.c:1566 INFO:RTC panic set [1970-09-27 23:24:08.156] Nss_syciSsiBp_proc nss_sycissibp.c:462 INFO:Nss_syciSsiBp_proc: STARTED [1970-09-27 23:24:08.188] ecda ecda.c:1113 INFO:ECDA CXC1326498%2, revision R3B01 started. (ecda_c64) [1970-09-27 23:24:08.760] bppSupervisor bpai_initBpai_if.c:216 INFO:bppSupervisor process has started, @(#)BP Application Interface (BPAI) version: 13.2 [1970-09-27 23:24:08.772] CbcServer cbc_server.c:521 INFO:LED(MISSING RESOURCE START) [1970-09-27 23:24:08.772] CbcServer cbc_server.c:572 INFO:BoardType: "RAX" FPGAs: 1 DSPs: 6 [1970-09-27 23:24:08.776] bmr bmr.c:2487 INFO:Board (re)start. [1970-09-27 23:24:09.788] hdr_clk hdr_clk.c:288 INFO:Estimated clock frequency: 193 MHz [1970-09-27 23:24:09.896] Cls_lcim_proc lcim.c:331 INFO:LCIM: Pid received from NS (GetServicePidRequest) [1970-09-27 23:24:11.496] bmr bmr.c:2495 INFO:BCP Rev 'CXC1323891_1-R26N01' started! [1970-09-27 23:24:11.500] bmr bmr.c:2527 INFO:BPP has started, supported BPAI versions are: 13.0 to 13.2 [1970-09-27 23:24:11.504] bmr bmr.c:2602 INFO:Board: 'RAXB' 'ROJ 119 2187/10' Rev 'R1' SerialNr ''. [1970-09-27 23:24:11.512] main_thread_func ../src/target/Cello/MAIN/main.cc:273 INFO:***RoseRT: PPC Environment [1970-09-27 23:24:11.520] application ../src/UbpDcTopLevelCapsuleC.cpp:263 INFO:LM_VERS=@(#)CXC1322173/1 R25J 2006-07-04 09:37:31 MEST 0a293774-0c3cd73b-2896 (RAX) [1970-09-27 23:24:11.520] hwLogHandler ../src/HwLogHandler.cpp:280 INFO:DC_SW_INFO=@(#)CXC1322173/1 R25J 2006-07-04 0 (RAX) [1970-09-27 23:24:11.532] ubpDcCapabillityHandlerCR1 ../src/UbpDcCapabilityHandlerC.cpp:1156 INFO:UbpDcCapabilityHandler: register in ose BPAI_GET_DP_LMC_PID_INFO_IND [1970-09-27 23:24:11.556] ubpDcDeviceManagerCR1 ../src/UbpDcDeviceManagerC.cpp:6370 INFO:Device Manager is alive [1970-09-27 23:24:11.556] ubpDcCdciConnectionHandlerCR1 ../src/UbpDcCdciConnectionHandlerC.cpp:880 INFO:Phantom process UbpTcDeviceControlPT created for UbpDcUbchsServer (PID = 0x100bf) [1970-09-27 23:24:11.556] ubpDcSbciConnectionHandlerCR1 ../src/UbpDcSbciConnectionHandlerC.cpp:813 INFO:Phantom process RaxServer created for UbpDcRaxServer (PID = 0x100c0) [1970-09-27 23:24:11.664] ubpDcDpConnectionHandler ../src/UbpDcDpConnectionHandlerC.cpp:986 INFO:Creating start/stop string for DPs [1970-09-27 23:24:11.668] ubpDcDpConnectionHandler ../src/UbpDcDpConnectionHandlerC.cpp:1008 INFO:Waiting for DPs to finish (re)booting [1970-09-27 23:24:11.668] application ../src/UbpDcTopLevelCapsuleC.cpp:343 INFO:DC application is running, i.e. all actors incarnated. [1970-09-27 23:24:38.180] CbcServer cbc_server.c:521 INFO:LED(MISSING RESOURCE END) [1970-09-27 23:24:38.180] CbcServer cbc_server.c:521 INFO:LED(MISSING RESOURCE START) [1970-09-27 23:24:38.184] CbcServer cbc_server.c:521 INFO:LED(LOAD TEST START)

[1970-09-27 23:24:38.216] blm blm.c:1893 INFO:Loading from LMC: CXP901085/1-R22K (RAX_LMC_3) [1970-09-27 23:24:38.316] bld bld_load.c:1091 INFO:Loaded: CXC1323761/1, revision: R2D to snid: 17 [1970-09-27 23:24:38.316] PARA0 bfp.c:1593 INFO:Configured for "PARA0" [1970-09-27 23:24:38.720] bld bld_load.c:1091 INFO:Loaded: CXC1322172/2, revision: R12H to snid: 1 [1970-09-27 23:24:39.320] bld bld_load.c:1091 INFO:Loaded: CXC1321358_2, revision: R21L to snid: 2 [1970-09-27 23:24:39.920] bld bld_load.c:1091 INFO:Loaded: CXC1321358_2, revision: R21L to snid: 3 [1970-09-27 23:24:40.520] bld bld_load.c:1091 INFO:Loaded: CXC1321358_2, revision: R21L to snid: 4 [1970-09-27 23:24:41.120] bld bld_load.c:1091 INFO:Loaded: CXC1321358_2, revision: R21L to snid: 5 [1970-09-27 23:24:41.564] bld bld_load.c:1091 INFO:Loaded: CXC1322146/1, revision: R11C to snid: 6 [1970-09-27 23:24:41.588] - bdp.c:1613 INFO:Interrupt process 'bdp_hpi3_int_DSP1' created OK! [1970-09-27 23:24:41.588] - bdp.c:1613 INFO:Interrupt process 'bdp_hpi3_int_DSP2' created OK! [1970-09-27 23:24:41.592] - bdp.c:1613 INFO:Interrupt process 'bdp_hpi3_int_DSP3' created OK! [1970-09-27 23:24:41.596] - bdp.c:1613 INFO:Interrupt process 'bdp_hpi3_int_DSP4' created OK! [1970-09-27 23:24:41.596] - bdp.c:1613 INFO:Interrupt process 'bdp_hpi3_int_DSP5' created OK! [1970-09-27 23:24:41.600] - bdp.c:1613 INFO:Interrupt process 'bdp_hpi3_int_DSP6' created OK! [1970-09-27 23:24:41.604] dpp1_main src/dpp_main.c:409 INFO:DPP: DPP [CYB10157/1_R13C] started for SNID = 1 : 0x0001 [1970-09-27 23:24:41.604] dpp1_main src/dpp_main.c:416 INFO:DPP: Application started for SNID = 1 : 0x0002 [1970-09-27 23:24:41.604] DEC_Boot ../dsp/sw/config/src/DecBoot.c:270 INFO:@(#)DEC build info: klintgun 10:53:57 Mar 27 2006 : 0x0003 [1970-09-27 23:24:41.604] DEC_Boot ../dsp/sw/config/src/DecBoot.c:271 INFO:@(#)DEC target : CAX1030053/2 : 0x0004 [1970-09-27 23:24:41.604] DEC_Boot ../dsp/sw/config/src/DecBoot.c:272 INFO:@(#)DEC compiler : TI TMS320C6x : 0x0005 [1970-09-27 23:24:41.604] DEC_Boot ../dsp/sw/config/src/DecBoot.c:273 INFO:@(#)DEC project : Espresso : 0x0006 [1970-09-27 23:24:41.604] DEC_Boot ../dsp/sw/config/src/DecBoot.c:274 INFO:@(#)DEC comment : : 0x0007 [1970-09-27 23:24:41.604] DEC_Boot ../dsp/sw/config/src/DecBoot.c:275 INFO:@(#)DEC PBOOT ver.: 2 : 0x0008 [1970-09-27 23:24:41.604] DEC_Boot ../dsp/sw/config/src/DecBoot.c:277 INFO:DSP frequency: 600 : 0x0009 [1970-09-27 23:24:41.604] DEC_Boot ../dsp/sw/config/src/EmifInit.c:305 INFO:DSP Param FU type = 1 Format Ver: = 0 : 0x000A [1970-09-27 23:24:41.604] DEC_Boot ../dsp/sw/config/src/EmifInit.c:308 INFO:DSP Param Gbl_Ctl_B = 0x2080 Ce_Ctl_b = 0x11124411 : 0x000B [1970-09-27 23:24:41.604] DEC_Boot ../dsp/sw/config/src/EmifInit.c:313 INFO:EMIF A GblCtl = 0x127A4 CeCtl0 = 0x109145C1 : 0x000C [1970-09-27 23:24:41.604] DEC_Boot ../dsp/sw/config/src/EmifInit.c:316 INFO:EMIF A CeCtl1 = 0xD0 CeCtl2 = 0x0 : 0x000D [1970-09-27 23:24:41.604] DEC_Boot ../dsp/sw/config/src/EmifInit.c:319 INFO:EMIF A CeCtl3 = 0x0 SdCtl = 0x46228000 : 0x000E [1970-09-27 23:24:41.604] DEC_Boot ../dsp/sw/config/src/EmifInit.c:322 INFO:EMIF A SdTim = 0x5EE618 SdExt = 0x5453D : 0x000F [1970-09-27 23:24:41.604] DEC_Boot ../dsp/sw/config/src/EmifInit.c:325 INFO:EMIF A CeSec0 = 0x0 CeSec1 = 0x0 : 0x0010 [1970-09-27 23:24:41.604] DEC_Boot ../dsp/sw/config/src/EmifInit.c:328 INFO:EMIF A CeSec2 = 0x0 CeSec3 = 0x0 : 0x0011

[1970-09-27 23:24:41.604] DEC_Boot ../dsp/sw/config/src/DecBoot.c:303 INFO:Pathfinder RESET is released by BP : 0x0012 [1970-09-27 23:24:41.604] DEC_Boot ../dsp/sw/config/src/DecBoot.c:319 INFO:Pathfinder version R1B : 0x0013 [1970-09-27 23:24:41.608] dpp2_main src/dpp_main.c:409 INFO:DPP: DPP [CYB10157/1_R13C] started for SNID = 2 : 0x0001 [1970-09-27 23:24:41.608] dpp2_main config.c:233 INFO:DEM buildinfo: lindeste Thu Jun 15 11:01:23 MEST 2006 (Wasa R3) : 0x0002 [1970-09-27 23:24:41.608] dpp2_main common_paramcheck.c:218 INFO:FU TYPE = 2 : 0x0003 [1970-09-27 23:24:41.608] dpp2_main common_paramcheck.c:219 INFO:Format revision = 0 : 0x0004 [1970-09-27 23:24:41.608] dpp2_main common_paramcheck.c:220 INFO:CPU frequency = 600 : 0x0005 [1970-09-27 23:24:41.608] dpp2_main common_paramcheck.c:222 INFO:EMIFA GblCtl_A = 0x2080 Ce0Ctl_A = 0x10e14422 : 0x0006 [1970-09-27 23:24:41.608] dpp2_main wasa_interface.c:3390 INFO:ASIC version = 5 : 0x0007 [1970-09-27 23:24:41.608] dpp2_main wasa_interface.c:1107 INFO:SWU WASA IF initialized. : 0x0008 [1970-09-27 23:24:41.612] dpp2_main rake_ctrl.c:990 INFO:SWU Rake Manager initialized. : 0x0009 [1970-09-27 23:24:41.612] dpp2_main dm_control.c:712 INFO:DEM_DM: control module initiated. : 0x000A [1970-09-27 23:24:41.612] dpp2_main gamma_sv_control.c:325 INFO:DEM_DM: Gamma SV module initiated : 0x000B [1970-09-27 23:24:41.612] dpp2_main dbg_manager.c:491 INFO:DEM_DM: Debug module initiated. : 0x000C [1970-09-27 23:24:41.612] dpp2_main self_test.c:379 INFO:DEM_DM: Selftest module initialted : 0x000D [1970-09-27 23:24:41.612] dpp2_main ws_manager.c:364 INFO:Widesearch Manager memory consumption = 3 kBytes : 0x000E [1970-09-27 23:24:41.612] dpp2_main ws_manager.c:368 INFO:SWU Widesearch Manager initialized. : 0x000F [1970-09-27 23:24:41.612] dpp2_main src/dpp_main.c:416 INFO:DPP: Application started for SNID = 2 : 0x0010 [1970-09-27 23:24:41.612] DEM0_RAKE searcher_manager.c:577 INFO:Rake service registered to PID 34 : 0x0011 [1970-09-27 23:24:41.612] DEM0_BP ocns_ctrl.c:648 INFO:Client 32 registered for OCNS_SRV. : 0x0012 [1970-09-27 23:24:41.612] DEM0_MDS rake_ctrl.c:1153 INFO:Client 33 subscribed for the RAKE_SYNC_SRV. : 0x0013 [1970-09-27 23:24:41.612] DEM0_MDS rake_ctrl.c:1141 INFO:Client 33 subscribed for RAKE_ISCP_RSCP_SRV. : 0x0014 [1970-09-27 23:24:41.612] DEM0_DM rake_ctrl.c:1147 INFO:Client 36 subscribed for RAKE_LFN_SRV : 0x0015 [1970-09-27 23:24:41.612] DEM0_DM rake_ctrl.c:1153 INFO:Client 36 subscribed for the RAKE_SYNC_SRV. : 0x0016 [1970-09-27 23:24:41.612] DEM0_DM rake_ctrl.c:1093 INFO:Client 36 registered for RAKE_RLS_CTRL_SRV. : 0x0017 [1970-09-27 23:24:41.612] DEM0_DM searcher_manager.c:536 INFO:Control service registered to PID 36 : 0x0018 [1970-09-27 23:24:41.612] DEM0_DM ws_manager.c:401 INFO:Client 36 registered for WS RLS CONTROL service. : 0x0019 [1970-09-27 23:24:41.612] DEM0_MEAS meas_manager.c:1502 INFO:SWU MEAS initialized and started : 0x001A [1970-09-27 23:24:41.612] DEM0_MEAS meas_handler.c:176 INFO:Measurement service registered to PID 42 : 0x001C [1970-09-27 23:24:41.612] DEM0_DM_DEBUG debug_handler.c:104 INFO:Debug service registerd to PID 38 : 0x001F [1970-09-27 23:24:41.616] DEM0_BP dispatch.c:445 INFO:SWU BPIF initialized : 0x0020 [1970-09-27 23:24:41.616] dpp3_main src/dpp_main.c:409 INFO:DPP: DPP [CYB10157/1_R13C] started for SNID = 3 : 0x0001

[1970-09-27 23:24:41.616] dpp3_main config.c:233 INFO:DEM buildinfo: lindeste Thu Jun 15 11:01:23 MEST 2006 (Wasa R3) : 0x0002 [1970-09-27 23:24:41.616] dpp3_main common_paramcheck.c:218 INFO:FU TYPE = 2 : 0x0003 [1970-09-27 23:24:41.616] dpp3_main common_paramcheck.c:219 INFO:Format revision = 0 : 0x0004 [1970-09-27 23:24:41.616] dpp3_main common_paramcheck.c:220 INFO:CPU frequency = 600 : 0x0005 [1970-09-27 23:24:41.616] dpp3_main common_paramcheck.c:222 INFO:EMIFA GblCtl_A = 0x2080 Ce0Ctl_A = 0x10e14422 : 0x0006 [1970-09-27 23:24:41.616] dpp3_main wasa_interface.c:3390 INFO:ASIC version = 5 : 0x0007 [1970-09-27 23:24:41.616] dpp3_main wasa_interface.c:1107 INFO:SWU WASA IF initialized. : 0x0008 [1970-09-27 23:24:41.616] dpp3_main rake_ctrl.c:990 INFO:SWU Rake Manager initialized. : 0x0009 [1970-09-27 23:24:41.616] dpp3_main dm_control.c:712 INFO:DEM_DM: control module initiated. : 0x000A [1970-09-27 23:24:41.616] dpp3_main gamma_sv_control.c:325 INFO:DEM_DM: Gamma SV module initiated : 0x000B [1970-09-27 23:24:41.620] dpp3_main dbg_manager.c:491 INFO:DEM_DM: Debug module initiated. : 0x000C [1970-09-27 23:24:41.620] dpp3_main self_test.c:379 INFO:DEM_DM: Selftest module initialted : 0x000D [1970-09-27 23:24:41.620] dpp3_main ws_manager.c:364 INFO:Widesearch Manager memory consumption = 3 kBytes : 0x000E [1970-09-27 23:24:41.620] dpp3_main ws_manager.c:368 INFO:SWU Widesearch Manager initialized. : 0x000F [1970-09-27 23:24:41.620] dpp3_main src/dpp_main.c:416 INFO:DPP: Application started for SNID = 3 : 0x0010 [1970-09-27 23:24:41.620] DEM1_RAKE searcher_manager.c:577 INFO:Rake service registered to PID 34 : 0x0011 [1970-09-27 23:24:41.620] DEM1_BP ocns_ctrl.c:648 INFO:Client 32 registered for OCNS_SRV. : 0x0012 [1970-09-27 23:24:41.620] DEM1_MDS rake_ctrl.c:1153 INFO:Client 33 subscribed for the RAKE_SYNC_SRV. : 0x0013 [1970-09-27 23:24:41.620] DEM1_MDS rake_ctrl.c:1141 INFO:Client 33 subscribed for RAKE_ISCP_RSCP_SRV. : 0x0014 [1970-09-27 23:24:41.620] DEM1_DM rake_ctrl.c:1147 INFO:Client 36 subscribed for RAKE_LFN_SRV : 0x0015 [1970-09-27 23:24:41.620] DEM1_DM rake_ctrl.c:1153 INFO:Client 36 subscribed for the RAKE_SYNC_SRV. : 0x0016 [1970-09-27 23:24:41.620] DEM1_DM rake_ctrl.c:1093 INFO:Client 36 registered for RAKE_RLS_CTRL_SRV. : 0x0017 [1970-09-27 23:24:41.620] DEM1_DM searcher_manager.c:536 INFO:Control service registered to PID 36 : 0x0018 [1970-09-27 23:24:41.620] DEM1_DM ws_manager.c:401 INFO:Client 36 registered for WS RLS CONTROL service. : 0x0019 [1970-09-27 23:24:41.620] DEM1_MEAS meas_manager.c:1502 INFO:SWU MEAS initialized and started : 0x001A [1970-09-27 23:24:41.620] DEM1_MEAS meas_handler.c:176 INFO:Measurement service registered to PID 42 : 0x001C [1970-09-27 23:24:41.620] DEM1_DM_DEBUG rake_ctrl.c:1100 INFO:Client 38 registered for RAKE_DBG_SRV. : 0x001E [1970-09-27 23:24:41.620] DEM1_BP dispatch.c:445 INFO:SWU BPIF initialized : 0x0020 [1970-09-27 23:24:41.624] dpp4_main src/dpp_main.c:409 INFO:DPP: DPP [CYB10157/1_R13C] started for SNID = 4 : 0x0001 [1970-09-27 23:24:41.624] dpp4_main config.c:233 INFO:DEM buildinfo: lindeste Thu Jun 15 11:01:23 MEST 2006 (Wasa R3) : 0x0002 [1970-09-27 23:24:41.624] dpp4_main common_paramcheck.c:218 INFO:FU TYPE = 2 : 0x0003 [1970-09-27 23:24:41.624] dpp4_main common_paramcheck.c:219 INFO:Format revision = 0 : 0x0004

[1970-09-27 23:24:41.624] dpp4_main common_paramcheck.c:220 INFO:CPU frequency = 600 : 0x0005 [1970-09-27 23:24:41.624] dpp4_main common_paramcheck.c:222 INFO:EMIFA GblCtl_A = 0x2080 Ce0Ctl_A = 0x10e14422 : 0x0006 [1970-09-27 23:24:41.624] dpp4_main wasa_interface.c:3390 INFO:ASIC version = 5 : 0x0007 [1970-09-27 23:24:41.624] dpp4_main wasa_interface.c:1107 INFO:SWU WASA IF initialized. : 0x0008 [1970-09-27 23:24:41.624] dpp4_main rake_ctrl.c:990 INFO:SWU Rake Manager initialized. : 0x0009 [1970-09-27 23:24:41.624] dpp4_main dm_control.c:712 INFO:DEM_DM: control module initiated. : 0x000A [1970-09-27 23:24:41.624] dpp4_main gamma_sv_control.c:325 INFO:DEM_DM: Gamma SV module initiated : 0x000B [1970-09-27 23:24:41.628] dpp4_main dbg_manager.c:491 INFO:DEM_DM: Debug module initiated. : 0x000C [1970-09-27 23:24:41.628] dpp4_main self_test.c:379 INFO:DEM_DM: Selftest module initialted : 0x000D [1970-09-27 23:24:41.628] dpp4_main ws_manager.c:364 INFO:Widesearch Manager memory consumption = 3 kBytes : 0x000E [1970-09-27 23:24:41.628] dpp4_main ws_manager.c:368 INFO:SWU Widesearch Manager initialized. : 0x000F [1970-09-27 23:24:41.628] dpp4_main src/dpp_main.c:416 INFO:DPP: Application started for SNID = 4 : 0x0010 [1970-09-27 23:24:41.628] DEM2_RAKE searcher_manager.c:577 INFO:Rake service registered to PID 34 : 0x0011 [1970-09-27 23:24:41.628] DEM2_BP ocns_ctrl.c:648 INFO:Client 32 registered for OCNS_SRV. : 0x0012 [1970-09-27 23:24:41.628] DEM2_MDS rake_ctrl.c:1153 INFO:Client 33 subscribed for the RAKE_SYNC_SRV. : 0x0013 [1970-09-27 23:24:41.628] DEM2_MDS rake_ctrl.c:1141 INFO:Client 33 subscribed for RAKE_ISCP_RSCP_SRV. : 0x0014 [1970-09-27 23:24:41.628] DEM2_DM rake_ctrl.c:1147 INFO:Client 36 subscribed for RAKE_LFN_SRV : 0x0015 [1970-09-27 23:24:41.628] DEM2_DM rake_ctrl.c:1153 INFO:Client 36 subscribed for the RAKE_SYNC_SRV. : 0x0016 [1970-09-27 23:24:41.628] DEM2_DM rake_ctrl.c:1093 INFO:Client 36 registered for RAKE_RLS_CTRL_SRV. : 0x0017 [1970-09-27 23:24:41.628] DEM2_DM searcher_manager.c:536 INFO:Control service registered to PID 36 : 0x0018 [1970-09-27 23:24:41.628] DEM2_DM ws_manager.c:401 INFO:Client 36 registered for WS RLS CONTROL service. : 0x0019 [1970-09-27 23:24:41.628] DEM2_MEAS rake_ctrl.c:1085 INFO:Client 42 registered for RAKE_L1_MEAS_SRV. : 0x001B [1970-09-27 23:24:41.628] DEM2_DM_DEBUG rake_ctrl.c:1100 INFO:Client 38 registered for RAKE_DBG_SRV. : 0x001E [1970-09-27 23:24:41.628] DEM2_BP dispatch.c:445 INFO:SWU BPIF initialized : 0x0020 [1970-09-27 23:24:41.632] dpp5_main src/dpp_main.c:409 INFO:DPP: DPP [CYB10157/1_R13C] started for SNID = 5 : 0x0001 [1970-09-27 23:24:41.632] dpp5_main config.c:233 INFO:DEM buildinfo: lindeste Thu Jun 15 11:01:23 MEST 2006 (Wasa R3) : 0x0002 [1970-09-27 23:24:41.632] dpp5_main common_paramcheck.c:218 INFO:FU TYPE = 2 : 0x0003 [1970-09-27 23:24:41.632] dpp5_main common_paramcheck.c:219 INFO:Format revision = 0 : 0x0004 [1970-09-27 23:24:41.632] dpp5_main common_paramcheck.c:220 INFO:CPU frequency = 600 : 0x0005 [1970-09-27 23:24:41.632] dpp5_main common_paramcheck.c:222 INFO:EMIFA GblCtl_A = 0x2080 Ce0Ctl_A = 0x10e14422 : 0x0006 [1970-09-27 23:24:41.632] dpp5_main wasa_interface.c:3390 INFO:ASIC version = 5 : 0x0007 [1970-09-27 23:24:41.632] dpp5_main wasa_interface.c:1107 INFO:SWU WASA IF initialized. : 0x0008

[1970-09-27 23:24:41.632] dpp5_main rake_ctrl.c:990 INFO:SWU Rake Manager initialized. : 0x0009 [1970-09-27 23:24:41.632] dpp5_main dm_control.c:712 INFO:DEM_DM: control module initiated. : 0x000A [1970-09-27 23:24:41.632] dpp5_main gamma_sv_control.c:325 INFO:DEM_DM: Gamma SV module initiated : 0x000B [1970-09-27 23:24:41.632] dpp5_main dbg_manager.c:491 INFO:DEM_DM: Debug module initiated. : 0x000C [1970-09-27 23:24:41.636] dpp5_main self_test.c:379 INFO:DEM_DM: Selftest module initialted : 0x000D [1970-09-27 23:24:41.636] dpp5_main ws_manager.c:364 INFO:Widesearch Manager memory consumption = 3 kBytes : 0x000E [1970-09-27 23:24:41.636] dpp5_main ws_manager.c:368 INFO:SWU Widesearch Manager initialized. : 0x000F [1970-09-27 23:24:41.636] dpp5_main src/dpp_main.c:416 INFO:DPP: Application started for SNID = 5 : 0x0010 [1970-09-27 23:24:41.636] DEM3_RAKE searcher_manager.c:577 INFO:Rake service registered to PID 34 : 0x0011 [1970-09-27 23:24:41.636] DEM3_BP ocns_ctrl.c:648 INFO:Client 32 registered for OCNS_SRV. : 0x0012 [1970-09-27 23:24:41.636] DEM3_MDS rake_ctrl.c:1153 INFO:Client 33 subscribed for the RAKE_SYNC_SRV. : 0x0013 [1970-09-27 23:24:41.636] DEM3_MDS rake_ctrl.c:1141 INFO:Client 33 subscribed for RAKE_ISCP_RSCP_SRV. : 0x0014 [1970-09-27 23:24:41.636] DEM3_DM rake_ctrl.c:1147 INFO:Client 36 subscribed for RAKE_LFN_SRV : 0x0015 [1970-09-27 23:24:41.636] DEM3_DM rake_ctrl.c:1153 INFO:Client 36 subscribed for the RAKE_SYNC_SRV. : 0x0016 [1970-09-27 23:24:41.636] DEM3_DM rake_ctrl.c:1093 INFO:Client 36 registered for RAKE_RLS_CTRL_SRV. : 0x0017 [1970-09-27 23:24:41.636] DEM3_DM searcher_manager.c:536 INFO:Control service registered to PID 36 : 0x0018 [1970-09-27 23:24:41.636] DEM3_DM ws_manager.c:401 INFO:Client 36 registered for WS RLS CONTROL service. : 0x0019 [1970-09-27 23:24:41.636] DEM3_MEAS meas_manager.c:1502 INFO:SWU MEAS initialized and started : 0x001A [1970-09-27 23:24:41.636] DEM3_MEAS meas_handler.c:176 INFO:Measurement service registered to PID 42 : 0x001C [1970-09-27 23:24:41.636] DEM3_DM_DEBUG rake_ctrl.c:1100 INFO:Client 38 registered for RAKE_DBG_SRV. : 0x001E [1970-09-27 23:24:41.636] DEM3_BP dispatch.c:445 INFO:SWU BPIF initialized : 0x0020 [1970-09-27 23:24:41.636] dpp6_main src/dpp_main.c:409 INFO:DPP: DPP [CYB10157/1_R13C] started for SNID = 6 : 0x0001 [1970-09-27 23:24:41.648] dpp6_main src/dpp_main.c:416 INFO:DPP: Application started for SNID = 6 : 0x0002 [1970-09-27 23:24:41.648] ra6_config src/initDSP.c:417 INFO:Contents of the RA PBOOT parameter area: : 0x0003 [1970-09-27 23:24:41.648] ra6_config src/initDSP.c:418 INFO:Number of parameters: 8 : 0x0004 [1970-09-27 23:24:41.648] ra6_config src/initDSP.c:419 INFO:FU type (RA = 3): 3 : 0x0005 [1970-09-27 23:24:41.648] ra6_config src/initDSP.c:420 INFO:Format revision: 0 : 0x0006 [1970-09-27 23:24:41.648] ra6_config src/initDSP.c:421 INFO:ROZ Product Number: ROZ104087/1 : 0x0007 [1970-09-27 23:24:41.648] ra6_config src/initDSP.c:422 INFO:ROZ R-state: P2A : 0x0008 [1970-09-27 23:24:41.648] ra6_config src/initDSP.c:423 INFO:Frequency (MHz): 600 : 0x0009 [1970-09-27 23:24:41.648] ra6_config src/initDSP.c:424 INFO:EMIFA GBLCTL register: 0x00000080 : 0x000A [1970-09-27 23:24:41.648] ra6_config src/initDSP.c:426 INFO:EMIFA_CE0CTL register: 0x20924321 : 0x000B

[1970-09-27 23:24:41.648] ra6_config src/initDSP.c:428 INFO:Guard word 1: 0xaaaa5555 : 0x000C [1970-09-27 23:24:41.648] ra6_config src/initDSP.c:429 INFO:Guard word 2: 0xaaaa5555 : 0x000D [1970-09-27 23:24:41.788] ra6_config src/config.c:272 INFO:RA DSP SNID=6 started. Version: CXC1322146/1_R11C01 , Build: Jun 22 2006 15:00:08 : 0x000E [1970-09-27 23:24:41.804] CbcServer cbc_server.c:521 INFO:LED(MISSING RESOURCE END) [1970-09-27 23:24:41.944] CbcServer cbc_server.c:521 INFO:LED(LOAD TEST END) [1970-09-27 23:24:51.752] DEM0_DM wasa_interface.c:490 INFO:Cluster 0 GAMMA_BUS config: : 0x0021 [1970-09-27 23:24:51.752] DEM0_DM wasa_interface.c:491 INFO:Gamma format = 2XOS : 0x0022 [1970-09-27 23:24:51.752] DEM0_DM wasa_interface.c:512 INFO:RG link | Branch <=> LG link : 0x0023 [1970-09-27 23:24:51.752] DEM0_DM wasa_interface.c:517 INFO: 4 | 0 <=> 0 : 0x0024 [1970-09-27 23:24:51.752] DEM0_DM wasa_interface.c:517 INFO: 4 | 1 <=> 1 : 0x0025 [1970-09-27 23:24:51.752] DEM0_DM wasa_interface.c:525 INFO: NC | 0 <=> 2 : 0x0026 [1970-09-27 23:24:51.752] DEM0_DM wasa_interface.c:525 INFO: NC | 0 <=> 3 : 0x0027 [1970-09-27 23:24:51.752] DEM0_DM wasa_interface.c:525 INFO: NC | 0 <=> 4 : 0x0028 [1970-09-27 23:24:51.752] DEM0_DM wasa_interface.c:525 INFO: NC | 0 <=> 5 : 0x0029 [1970-09-27 23:24:51.752] DEM0_DM wasa_interface.c:525 INFO: NC | 0 <=> 6 : 0x002A [1970-09-27 23:24:51.752] DEM0_DM wasa_interface.c:525 INFO: NC | 0 <=> 7 : 0x002B [1970-09-27 23:24:51.752] DEM0_DM wasa_interface.c:525 INFO: NC | 0 <=> 8 : 0x002C [1970-09-27 23:24:51.752] DEM0_DM wasa_interface.c:525 INFO: NC | 0 <=> 9 : 0x002D [1970-09-27 23:24:51.752] DEM0_DM wasa_interface.c:525 INFO: NC | 0 <=> 10 : 0x002E [1970-09-27 23:24:51.752] DEM0_DM wasa_interface.c:525 INFO: NC | 0 <=> 11 : 0x002F [1970-09-27 23:24:51.752] DEM0_DM wasa_interface.c:531 INFO:RG range 0..11 or NC, LG range: 0..11 : 0x0030 [1970-09-27 23:24:51.752] DEM1_DM wasa_interface.c:490 INFO:Cluster 1 GAMMA_BUS config: : 0x0021 [1970-09-27 23:24:51.752] DEM1_DM wasa_interface.c:491 INFO:Gamma format = 2XOS : 0x0022 [1970-09-27 23:24:51.752] DEM1_DM wasa_interface.c:512 INFO:RG link | Branch <=> LG link : 0x0023 [1970-09-27 23:24:51.752] DEM1_DM wasa_interface.c:517 INFO: 4 | 0 <=> 0 : 0x0024 [1970-09-27 23:24:51.752] DEM1_DM wasa_interface.c:517 INFO: 4 | 1 <=> 1 : 0x0025 [1970-09-27 23:24:51.752] DEM1_DM wasa_interface.c:525 INFO: NC | 0 <=> 2 : 0x0026 [1970-09-27 23:24:51.752] DEM1_DM wasa_interface.c:525 INFO: NC | 0 <=> 3 : 0x0027 [1970-09-27 23:24:51.752] DEM1_DM wasa_interface.c:525 INFO: NC | 0 <=> 4 : 0x0028 [1970-09-27 23:24:51.752] DEM1_DM wasa_interface.c:525 INFO: NC | 0 <=> 5 : 0x0029 [1970-09-27 23:24:51.752] DEM1_DM wasa_interface.c:525 INFO: NC | 0 <=> 6 : 0x002A [1970-09-27 23:24:51.752] DEM1_DM wasa_interface.c:525 INFO: NC | 0 <=> 7 : 0x002B [1970-09-27 23:24:51.752] DEM1_DM wasa_interface.c:525 INFO: NC | 0 <=> 8 : 0x002C

[1970-09-27 23:24:51.752] DEM1_DM wasa_interface.c:525 INFO: NC | 0 <=> 9 : 0x002D [1970-09-27 23:24:51.752] DEM1_DM wasa_interface.c:525 INFO: NC | 0 <=> 10 : 0x002E [1970-09-27 23:24:51.752] DEM1_DM wasa_interface.c:525 INFO: NC | 0 <=> 11 : 0x002F [1970-09-27 23:24:51.752] DEM1_DM wasa_interface.c:531 INFO:RG range 0..11 or NC, LG range: 0..11 : 0x0030 [1970-09-27 23:24:51.752] DEM2_DM wasa_interface.c:490 INFO:Cluster 2 GAMMA_BUS config: : 0x0021 [1970-09-27 23:24:51.752] DEM2_DM wasa_interface.c:491 INFO:Gamma format = 2XOS : 0x0022 [1970-09-27 23:24:51.752] DEM2_DM wasa_interface.c:512 INFO:RG link | Branch <=> LG link : 0x0023 [1970-09-27 23:24:51.752] DEM2_DM wasa_interface.c:517 INFO: 4 | 0 <=> 0 : 0x0024 [1970-09-27 23:24:51.752] DEM2_DM wasa_interface.c:517 INFO: 4 | 1 <=> 1 : 0x0025 [1970-09-27 23:24:51.752] DEM2_DM wasa_interface.c:525 INFO: NC | 0 <=> 2 : 0x0026 [1970-09-27 23:24:51.752] DEM2_DM wasa_interface.c:525 INFO: NC | 0 <=> 3 : 0x0027 [1970-09-27 23:24:51.752] DEM2_DM wasa_interface.c:525 INFO: NC | 0 <=> 4 : 0x0028 [1970-09-27 23:24:51.752] DEM2_DM wasa_interface.c:525 INFO: NC | 0 <=> 5 : 0x0029 [1970-09-27 23:24:51.756] DEM2_DM wasa_interface.c:525 INFO: NC | 0 <=> 6 : 0x002A [1970-09-27 23:24:51.756] DEM2_DM wasa_interface.c:525 INFO: NC | 0 <=> 7 : 0x002B [1970-09-27 23:24:51.756] DEM2_DM wasa_interface.c:525 INFO: NC | 0 <=> 8 : 0x002C [1970-09-27 23:24:51.756] DEM2_DM wasa_interface.c:525 INFO: NC | 0 <=> 9 : 0x002D [1970-09-27 23:24:51.756] DEM2_DM wasa_interface.c:525 INFO: NC | 0 <=> 10 : 0x002E [1970-09-27 23:24:51.756] DEM2_DM wasa_interface.c:525 INFO: NC | 0 <=> 11 : 0x002F [1970-09-27 23:24:51.756] DEM2_DM wasa_interface.c:531 INFO:RG range 0..11 or NC, LG range: 0..11 : 0x0030 [1970-09-27 23:24:51.756] DEM3_DM wasa_interface.c:490 INFO:Cluster 3 GAMMA_BUS config: : 0x0021 [1970-09-27 23:24:51.756] DEM3_DM wasa_interface.c:491 INFO:Gamma format = 2XOS : 0x0022 [1970-09-27 23:24:51.756] DEM3_DM wasa_interface.c:512 INFO:RG link | Branch <=> LG link : 0x0023 [1970-09-27 23:24:51.756] DEM3_DM wasa_interface.c:517 INFO: 4 | 0 <=> 0 : 0x0024 [1970-09-27 23:24:51.756] DEM3_DM wasa_interface.c:517 INFO: 4 | 1 <=> 1 : 0x0025 [1970-09-27 23:24:51.756] DEM3_DM wasa_interface.c:525 INFO: NC | 0 <=> 2 : 0x0026 [1970-09-27 23:24:51.756] DEM3_DM wasa_interface.c:525 INFO: NC | 0 <=> 3 : 0x0027 [1970-09-27 23:24:51.756] DEM3_DM wasa_interface.c:525 INFO: NC | 0 <=> 4 : 0x0028 [1970-09-27 23:24:51.756] DEM3_DM wasa_interface.c:525 INFO: NC | 0 <=> 5 : 0x0029 [1970-09-27 23:24:51.756] DEM3_DM wasa_interface.c:525 INFO: NC | 0 <=> 6 : 0x002A [1970-09-27 23:24:51.756] DEM3_DM wasa_interface.c:525 INFO: NC | 0 <=> 7 : 0x002B [1970-09-27 23:24:51.756] DEM3_DM wasa_interface.c:525 INFO: NC | 0 <=> 8 : 0x002C

[1970-09-27 23:24:51.756] DEM3_DM wasa_interface.c:525 INFO: NC | 0 <=> 9 : 0x002D [1970-09-27 23:24:51.756] DEM3_DM wasa_interface.c:525 INFO: NC | 0 <=> 10 : 0x002E [1970-09-27 23:24:51.756] DEM3_DM wasa_interface.c:525 INFO: NC | 0 <=> 11 : 0x002F [1970-09-27 23:24:51.756] DEM3_DM wasa_interface.c:531 INFO:RG range 0..11 or NC, LG range: 0..11 : 0x0030 [1970-09-27 23:24:51.972] DEM0_DM wasa_interface.c:490 INFO:Cluster 0 GAMMA_BUS config: : 0x0031 [1970-09-27 23:24:51.976] DEM0_DM wasa_interface.c:491 INFO:Gamma format = 2XOS : 0x0032 [1970-09-27 23:24:51.976] DEM0_DM wasa_interface.c:512 INFO:RG link | Branch <=> LG link : 0x0033 [1970-09-27 23:24:51.976] DEM0_DM wasa_interface.c:517 INFO: 4 | 0 <=> 0 : 0x0034 [1970-09-27 23:24:51.976] DEM0_DM wasa_interface.c:517 INFO: 4 | 1 <=> 1 : 0x0035 [1970-09-27 23:24:51.976] DEM0_DM wasa_interface.c:517 INFO: 8 | 0 <=> 2 : 0x0036 [1970-09-27 23:24:51.976] DEM0_DM wasa_interface.c:517 INFO: 8 | 1 <=> 3 : 0x0037 [1970-09-27 23:24:51.976] DEM0_DM wasa_interface.c:525 INFO: NC | 0 <=> 4 : 0x0038 [1970-09-27 23:24:51.976] DEM0_DM wasa_interface.c:525 INFO: NC | 0 <=> 5 : 0x0039 [1970-09-27 23:24:51.976] DEM0_DM wasa_interface.c:525 INFO: NC | 0 <=> 6 : 0x003A [1970-09-27 23:24:51.976] DEM0_DM wasa_interface.c:525 INFO: NC | 0 <=> 7 : 0x003B [1970-09-27 23:24:51.976] DEM0_DM wasa_interface.c:525 INFO: NC | 0 <=> 8 : 0x003C [1970-09-27 23:24:51.976] DEM0_DM wasa_interface.c:525 INFO: NC | 0 <=> 9 : 0x003D [1970-09-27 23:24:51.976] DEM0_DM wasa_interface.c:525 INFO: NC | 0 <=> 10 : 0x003E [1970-09-27 23:24:51.976] DEM0_DM wasa_interface.c:525 INFO: NC | 0 <=> 11 : 0x003F [1970-09-27 23:24:51.976] DEM0_DM wasa_interface.c:531 INFO:RG range 0..11 or NC, LG range: 0..11 : 0x0040 [1970-09-27 23:24:51.976] DEM1_DM wasa_interface.c:490 INFO:Cluster 1 GAMMA_BUS config: : 0x0031 [1970-09-27 23:24:51.976] DEM1_DM wasa_interface.c:491 INFO:Gamma format = 2XOS : 0x0032 [1970-09-27 23:24:51.976] DEM1_DM wasa_interface.c:512 INFO:RG link | Branch <=> LG link : 0x0033 [1970-09-27 23:24:51.976] DEM1_DM wasa_interface.c:517 INFO: 4 | 0 <=> 0 : 0x0034 [1970-09-27 23:24:51.976] DEM1_DM wasa_interface.c:517 INFO: 4 | 1 <=> 1 : 0x0035 [1970-09-27 23:24:51.976] DEM1_DM wasa_interface.c:517 INFO: 8 | 0 <=> 2 : 0x0036 [1970-09-27 23:24:51.976] DEM1_DM wasa_interface.c:517 INFO: 8 | 1 <=> 3 : 0x0037 [1970-09-27 23:24:51.976] DEM1_DM wasa_interface.c:525 INFO: NC | 0 <=> 4 : 0x0038 [1970-09-27 23:24:51.976] DEM1_DM wasa_interface.c:525 INFO: NC | 0 <=> 5 : 0x0039 [1970-09-27 23:24:51.976] DEM1_DM wasa_interface.c:525 INFO: NC | 0 <=> 6 : 0x003A [1970-09-27 23:24:51.976] DEM1_DM wasa_interface.c:525 INFO: NC | 0 <=> 7 : 0x003B [1970-09-27 23:24:51.976] DEM1_DM wasa_interface.c:525 INFO: NC | 0 <=> 8 : 0x003C

[1970-09-27 23:24:51.976] DEM1_DM wasa_interface.c:525 INFO: NC | 0 <=> 9 : 0x003D [1970-09-27 23:24:51.976] DEM1_DM wasa_interface.c:525 INFO: NC | 0 <=> 10 : 0x003E [1970-09-27 23:24:51.976] DEM1_DM wasa_interface.c:525 INFO: NC | 0 <=> 11 : 0x003F [1970-09-27 23:24:51.976] DEM1_DM wasa_interface.c:531 INFO:RG range 0..11 or NC, LG range: 0..11 : 0x0040 [1970-09-27 23:24:51.976] DEM2_DM wasa_interface.c:490 INFO:Cluster 2 GAMMA_BUS config: : 0x0031 [1970-09-27 23:24:51.976] DEM2_DM wasa_interface.c:491 INFO:Gamma format = 2XOS : 0x0032 [1970-09-27 23:24:51.976] DEM2_DM wasa_interface.c:512 INFO:RG link | Branch <=> LG link : 0x0033 [1970-09-27 23:24:51.976] DEM2_DM wasa_interface.c:517 INFO: 4 | 0 <=> 0 : 0x0034 [1970-09-27 23:24:51.976] DEM2_DM wasa_interface.c:517 INFO: 4 | 1 <=> 1 : 0x0035 [1970-09-27 23:24:51.976] DEM2_DM wasa_interface.c:517 INFO: 8 | 0 <=> 2 : 0x0036 [1970-09-27 23:24:51.976] DEM2_DM wasa_interface.c:517 INFO: 8 | 1 <=> 3 : 0x0037 [1970-09-27 23:24:51.976] DEM2_DM wasa_interface.c:525 INFO: NC | 0 <=> 4 : 0x0038 [1970-09-27 23:24:51.976] DEM2_DM wasa_interface.c:525 INFO: NC | 0 <=> 5 : 0x0039 [1970-09-27 23:24:51.976] DEM2_DM wasa_interface.c:525 INFO: NC | 0 <=> 6 : 0x003A [1970-09-27 23:24:51.976] DEM2_DM wasa_interface.c:525 INFO: NC | 0 <=> 7 : 0x003B [1970-09-27 23:24:51.976] DEM2_DM wasa_interface.c:525 INFO: NC | 0 <=> 8 : 0x003C [1970-09-27 23:24:51.976] DEM2_DM wasa_interface.c:525 INFO: NC | 0 <=> 9 : 0x003D [1970-09-27 23:24:51.976] DEM2_DM wasa_interface.c:525 INFO: NC | 0 <=> 10 : 0x003E [1970-09-27 23:24:51.976] DEM2_DM wasa_interface.c:525 INFO: NC | 0 <=> 11 : 0x003F [1970-09-27 23:24:51.976] DEM2_DM wasa_interface.c:531 INFO:RG range 0..11 or NC, LG range: 0..11 : 0x0040 [1970-09-27 23:24:51.976] DEM3_DM wasa_interface.c:490 INFO:Cluster 3 GAMMA_BUS config: : 0x0031 [1970-09-27 23:24:51.976] DEM3_DM wasa_interface.c:491 INFO:Gamma format = 2XOS : 0x0032 [1970-09-27 23:24:51.976] DEM3_DM wasa_interface.c:512 INFO:RG link | Branch <=> LG link : 0x0033 [1970-09-27 23:24:51.976] DEM3_DM wasa_interface.c:517 INFO: 4 | 0 <=> 0 : 0x0034 [1970-09-27 23:24:51.976] DEM3_DM wasa_interface.c:517 INFO: 4 | 1 <=> 1 : 0x0035 [1970-09-27 23:24:51.976] DEM3_DM wasa_interface.c:517 INFO: 8 | 0 <=> 2 : 0x0036 [1970-09-27 23:24:51.976] DEM3_DM wasa_interface.c:517 INFO: 8 | 1 <=> 3 : 0x0037 [1970-09-27 23:24:51.976] DEM3_DM wasa_interface.c:525 INFO: NC | 0 <=> 4 : 0x0038 [1970-09-27 23:24:51.976] DEM3_DM wasa_interface.c:525 INFO: NC | 0 <=> 5 : 0x0039 [1970-09-27 23:24:51.976] DEM3_DM wasa_interface.c:525 INFO: NC | 0 <=> 6 : 0x003A [1970-09-27 23:24:51.976] DEM3_DM wasa_interface.c:525 INFO: NC | 0 <=> 7 : 0x003B [1970-09-27 23:24:51.976] DEM3_DM wasa_interface.c:525 INFO: NC | 0 <=> 8 : 0x003C

[1970-09-27 23:24:51.976] DEM3_DM wasa_interface.c:525 INFO: NC | 0 <=> 9 : 0x003D [1970-09-27 23:24:51.976] DEM3_DM wasa_interface.c:525 INFO: NC | 0 <=> 10 : 0x003E [1970-09-27 23:24:51.976] DEM3_DM wasa_interface.c:525 INFO: NC | 0 <=> 11 : 0x003F [1970-09-27 23:24:51.976] DEM3_DM wasa_interface.c:531 INFO:RG range 0..11 or NC, LG range: 0..11 : 0x0040 [1970-09-27 23:24:52.184] DEM0_DM wasa_interface.c:490 INFO:Cluster 0 GAMMA_BUS config: : 0x0041 [1970-09-27 23:24:52.184] DEM0_DM wasa_interface.c:491 INFO:Gamma format = 2XOS : 0x0042 [1970-09-27 23:24:52.184] DEM0_DM wasa_interface.c:512 INFO:RG link | Branch <=> LG link : 0x0043 [1970-09-27 23:24:52.184] DEM0_DM wasa_interface.c:517 INFO: 4 | 0 <=> 0 : 0x0044 [1970-09-27 23:24:52.184] DEM0_DM wasa_interface.c:517 INFO: 4 | 1 <=> 1 : 0x0045 [1970-09-27 23:24:52.184] DEM0_DM wasa_interface.c:517 INFO: 8 | 0 <=> 2 : 0x0046 [1970-09-27 23:24:52.184] DEM0_DM wasa_interface.c:517 INFO: 8 | 1 <=> 3 : 0x0047 [1970-09-27 23:24:52.184] DEM0_DM wasa_interface.c:517 INFO: 0 | 0 <=> 4 : 0x0048 [1970-09-27 23:24:52.184] DEM0_DM wasa_interface.c:517 INFO: 0 | 1 <=> 5 : 0x0049 [1970-09-27 23:24:52.184] DEM0_DM wasa_interface.c:525 INFO: NC | 0 <=> 6 : 0x004A [1970-09-27 23:24:52.184] DEM0_DM wasa_interface.c:525 INFO: NC | 0 <=> 7 : 0x004B [1970-09-27 23:24:52.184] DEM0_DM wasa_interface.c:525 INFO: NC | 0 <=> 8 : 0x004C [1970-09-27 23:24:52.184] DEM0_DM wasa_interface.c:525 INFO: NC | 0 <=> 9 : 0x004D [1970-09-27 23:24:52.184] DEM0_DM wasa_interface.c:525 INFO: NC | 0 <=> 10 : 0x004E [1970-09-27 23:24:52.184] DEM0_DM wasa_interface.c:525 INFO: NC | 0 <=> 11 : 0x004F [1970-09-27 23:24:52.184] DEM0_DM wasa_interface.c:531 INFO:RG range 0..11 or NC, LG range: 0..11 : 0x0050 [1970-09-27 23:24:52.184] DEM1_DM wasa_interface.c:490 INFO:Cluster 1 GAMMA_BUS config: : 0x0041 [1970-09-27 23:24:52.184] DEM1_DM wasa_interface.c:491 INFO:Gamma format = 2XOS : 0x0042 [1970-09-27 23:24:52.184] DEM1_DM wasa_interface.c:512 INFO:RG link | Branch <=> LG link : 0x0043 [1970-09-27 23:24:52.184] DEM1_DM wasa_interface.c:517 INFO: 4 | 0 <=> 0 : 0x0044 [1970-09-27 23:24:52.184] DEM1_DM wasa_interface.c:517 INFO: 4 | 1 <=> 1 : 0x0045 [1970-09-27 23:24:52.184] DEM1_DM wasa_interface.c:517 INFO: 8 | 0 <=> 2 : 0x0046 [1970-09-27 23:24:52.184] DEM1_DM wasa_interface.c:517 INFO: 8 | 1 <=> 3 : 0x0047 [1970-09-27 23:24:52.184] DEM1_DM wasa_interface.c:517 INFO: 0 | 0 <=> 4 : 0x0048 [1970-09-27 23:24:52.184] DEM1_DM wasa_interface.c:517 INFO: 0 | 1 <=> 5 : 0x0049 [1970-09-27 23:24:52.184] DEM1_DM wasa_interface.c:525 INFO: NC | 0 <=> 6 : 0x004A [1970-09-27 23:24:52.184] DEM1_DM wasa_interface.c:525 INFO: NC | 0 <=> 7 : 0x004B [1970-09-27 23:24:52.184] DEM1_DM wasa_interface.c:525 INFO: NC | 0 <=> 8 : 0x004C

[1970-09-27 23:24:52.184] DEM1_DM wasa_interface.c:525 INFO: NC | 0 <=> 9 : 0x004D [1970-09-27 23:24:52.188] DEM1_DM wasa_interface.c:525 INFO: NC | 0 <=> 10 : 0x004E [1970-09-27 23:24:52.188] DEM1_DM wasa_interface.c:525 INFO: NC | 0 <=> 11 : 0x004F [1970-09-27 23:24:52.188] DEM1_DM wasa_interface.c:531 INFO:RG range 0..11 or NC, LG range: 0..11 : 0x0050 [1970-09-27 23:24:52.188] DEM2_DM wasa_interface.c:490 INFO:Cluster 2 GAMMA_BUS config: : 0x0041 [1970-09-27 23:24:52.188] DEM2_DM wasa_interface.c:491 INFO:Gamma format = 2XOS : 0x0042 [1970-09-27 23:24:52.188] DEM2_DM wasa_interface.c:512 INFO:RG link | Branch <=> LG link : 0x0043 [1970-09-27 23:24:52.188] DEM2_DM wasa_interface.c:517 INFO: 4 | 0 <=> 0 : 0x0044 [1970-09-27 23:24:52.188] DEM2_DM wasa_interface.c:517 INFO: 4 | 1 <=> 1 : 0x0045 [1970-09-27 23:24:52.188] DEM2_DM wasa_interface.c:517 INFO: 8 | 0 <=> 2 : 0x0046 [1970-09-27 23:24:52.188] DEM2_DM wasa_interface.c:517 INFO: 8 | 1 <=> 3 : 0x0047 [1970-09-27 23:24:52.188] DEM2_DM wasa_interface.c:517 INFO: 0 | 0 <=> 4 : 0x0048 [1970-09-27 23:24:52.188] DEM2_DM wasa_interface.c:517 INFO: 0 | 1 <=> 5 : 0x0049 [1970-09-27 23:24:52.188] DEM2_DM wasa_interface.c:525 INFO: NC | 0 <=> 6 : 0x004A [1970-09-27 23:24:52.188] DEM2_DM wasa_interface.c:525 INFO: NC | 0 <=> 7 : 0x004B [1970-09-27 23:24:52.188] DEM2_DM wasa_interface.c:525 INFO: NC | 0 <=> 8 : 0x004C [1970-09-27 23:24:52.188] DEM2_DM wasa_interface.c:525 INFO: NC | 0 <=> 9 : 0x004D [1970-09-27 23:24:52.188] DEM2_DM wasa_interface.c:525 INFO: NC | 0 <=> 10 : 0x004E [1970-09-27 23:24:52.188] DEM2_DM wasa_interface.c:525 INFO: NC | 0 <=> 11 : 0x004F [1970-09-27 23:24:52.188] DEM2_DM wasa_interface.c:531 INFO:RG range 0..11 or NC, LG range: 0..11 : 0x0050 [1970-09-27 23:24:52.188] DEM3_DM wasa_interface.c:490 INFO:Cluster 3 GAMMA_BUS config: : 0x0041 [1970-09-27 23:24:52.188] DEM3_DM wasa_interface.c:491 INFO:Gamma format = 2XOS : 0x0042 [1970-09-27 23:24:52.188] DEM3_DM wasa_interface.c:512 INFO:RG link | Branch <=> LG link : 0x0043 [1970-09-27 23:24:52.188] DEM3_DM wasa_interface.c:517 INFO: 4 | 0 <=> 0 : 0x0044 [1970-09-27 23:24:52.188] DEM3_DM wasa_interface.c:517 INFO: 4 | 1 <=> 1 : 0x0045 [1970-09-27 23:24:52.188] DEM3_DM wasa_interface.c:517 INFO: 8 | 0 <=> 2 : 0x0046 [1970-09-27 23:24:52.188] DEM3_DM wasa_interface.c:517 INFO: 8 | 1 <=> 3 : 0x0047 [1970-09-27 23:24:52.188] DEM3_DM wasa_interface.c:517 INFO: 0 | 0 <=> 4 : 0x0048 [1970-09-27 23:24:52.188] DEM3_DM wasa_interface.c:517 INFO: 0 | 1 <=> 5 : 0x0049 [1970-09-27 23:24:52.188] DEM3_DM wasa_interface.c:525 INFO: NC | 0 <=> 6 : 0x004A [1970-09-27 23:24:52.188] DEM3_DM wasa_interface.c:525 INFO: NC | 0 <=> 7 : 0x004B [1970-09-27 23:24:52.188] DEM3_DM wasa_interface.c:525 INFO: NC | 0 <=> 8 : 0x004C

[1970-09-27 23:24:52.188] DEM3_DM wasa_interface.c:525 INFO: NC | 0 <=> 9 : 0x004D [1970-09-27 23:24:52.188] DEM3_DM wasa_interface.c:525 INFO: NC | 0 <=> 10 : 0x004E [1970-09-27 23:24:52.188] DEM3_DM wasa_interface.c:525 INFO: NC | 0 <=> 11 : 0x004F [1970-09-27 23:24:52.188] DEM3_DM wasa_interface.c:531 INFO:RG range 0..11 or NC, LG range: 0..11 : 0x0050 AFter restart RAX=slot8 [1970-09-28 13:29:24.648] DEM1_DM wasa_interface.c:525 INFO: NC | 0 <=> 11 : 0x004F [1970-09-28 13:29:24.648] DEM1_DM wasa_interface.c:531 INFO:RG range 0..11 or NC, LG range: 0..11 : 0x0050 [1970-09-28 13:29:24.648] DEM2_DM wasa_interface.c:490 INFO:Cluster 2 GAMMA_BUS config: : 0x0041 [1970-09-28 13:29:24.648] DEM2_DM wasa_interface.c:491 INFO:Gamma format = 2XOS : 0x0042 [1970-09-28 13:29:24.648] DEM2_DM wasa_interface.c:512 INFO:RG link | Branch <=> LG link : 0x0043 [1970-09-28 13:29:24.648] DEM2_DM wasa_interface.c:517 INFO: 4 | 0 <=> 0 : 0x0044 [1970-09-28 13:29:24.648] DEM2_DM wasa_interface.c:517 INFO: 4 | 1 <=> 1 : 0x0045 [1970-09-28 13:29:24.648] DEM2_DM wasa_interface.c:517 INFO: 8 | 0 <=> 2 : 0x0046 [1970-09-28 13:29:24.648] DEM2_DM wasa_interface.c:517 INFO: 8 | 1 <=> 3 : 0x0047 [1970-09-28 13:29:24.648] DEM2_DM wasa_interface.c:517 INFO: 0 | 0 <=> 4 : 0x0048 [1970-09-28 13:29:24.648] DEM2_DM wasa_interface.c:517 INFO: 0 | 1 <=> 5 : 0x0049 [1970-09-28 13:29:24.648] DEM2_DM wasa_interface.c:525 INFO: NC | 0 <=> 6 : 0x004A [1970-09-28 13:29:24.648] DEM2_DM wasa_interface.c:525 INFO: NC | 0 <=> 7 : 0x004B [1970-09-28 13:29:24.648] DEM2_DM wasa_interface.c:525 INFO: NC | 0 <=> 8 : 0x004C [1970-09-28 13:29:24.648] DEM2_DM wasa_interface.c:525 INFO: NC | 0 <=> 9 : 0x004D [1970-09-28 13:29:24.648] DEM2_DM wasa_interface.c:525 INFO: NC | 0 <=> 10 : 0x004E [1970-09-28 13:29:24.648] DEM2_DM wasa_interface.c:525 INFO: NC | 0 <=> 11 : 0x004F [1970-09-28 13:29:24.648] DEM2_DM wasa_interface.c:531 INFO:RG range 0..11 or NC, LG range: 0..11 : 0x0050 [1970-09-28 13:29:24.648] DEM3_DM wasa_interface.c:490 INFO:Cluster 3 GAMMA_BUS config: : 0x0041 [1970-09-28 13:29:24.648] DEM3_DM wasa_interface.c:491 INFO:Gamma format = 2XOS : 0x0042 [1970-09-28 13:29:24.648] DEM3_DM wasa_interface.c:512 INFO:RG link | Branch <=> LG link : 0x0043 [1970-09-28 13:29:24.648] DEM3_DM wasa_interface.c:517 INFO: 4 | 0 <=> 0 : 0x0044 [1970-09-28 13:29:24.648] DEM3_DM wasa_interface.c:517 INFO: 4 | 1 <=> 1 : 0x0045 [1970-09-28 13:29:24.648] DEM3_DM wasa_interface.c:517 INFO: 8 | 0 <=> 2 : 0x0046 [1970-09-28 13:29:24.648] DEM3_DM wasa_interface.c:517 INFO: 8 | 1 <=> 3 : 0x0047 [1970-09-28 13:29:24.648] DEM3_DM wasa_interface.c:517 INFO: 0 | 0 <=> 4 : 0x0048

[1970-09-28 13:29:24.648] DEM3_DM wasa_interface.c:517 INFO: 0 | 1 <=> 5 : 0x0049 [1970-09-28 13:29:24.648] DEM3_DM wasa_interface.c:525 INFO: NC | 0 <=> 6 : 0x004A [1970-09-28 13:29:24.648] DEM3_DM wasa_interface.c:525 INFO: NC | 0 <=> 7 : 0x004B [1970-09-28 13:29:24.648] DEM3_DM wasa_interface.c:525 INFO: NC | 0 <=> 8 : 0x004C [1970-09-28 13:29:24.648] DEM3_DM wasa_interface.c:525 INFO: NC | 0 <=> 9 : 0x004D [1970-09-28 13:29:24.648] DEM3_DM wasa_interface.c:525 INFO: NC | 0 <=> 10 : 0x004E [1970-09-28 13:29:24.648] DEM3_DM wasa_interface.c:525 INFO: NC | 0 <=> 11 : 0x004F [1970-09-28 13:29:24.648] DEM3_DM wasa_interface.c:531 INFO:RG range 0..11 or NC, LG range: 0..11 : 0x0050 RAX=slot=9

APPENDIX E: STDH Following 275 devices are up: --------------------------------------------------------------------------- DEVICE STATE MOD LNH TYPE DEV/SPM DEV-ID SPM-ID --------------------------------------------------------------------------- 1 001900/sp0.lnh PDR 11 MS/19/1/1 MS/19/1 1 001900/sp1.lnh CC 11 MS/19/2/1 MS/19/2 1 001900/sp2.lnh DC 11 MS/19/3/1 MS/19/3 1 001900/sp3.lnh DC 11 MS/19/3/2 MS/19/4 1 001900/sp4.lnh DC 11 MS/19/3/3 MS/19/5 1 002000/sp0.lnh PDR 11 MS/20/1/1 MS/20/1 1 002000/sp1.lnh CC 11 MS/20/2/1 MS/20/2 1 002000/sp2.lnh DC 11 MS/20/3/1 MS/20/3 1 002000/sp3.lnh DC 11 MS/20/3/2 MS/20/4 1 002000/sp4.lnh DC 11 MS/20/3/3 MS/20/5 1 002100/sp0.lnh PDR 11 MS/21/1/1 MS/21/1 1 002100/sp1.lnh CC 11 MS/21/2/1 MS/21/2 1 002100/sp2.lnh DC 11 MS/21/3/1 MS/21/3 1 002100/sp3.lnh DC 11 MS/21/3/2 MS/21/4 1 002100/sp4.lnh DC 11 MS/21/3/3 MS/21/5 8 002200/sp0.lnh PDR 11 MS/22/1/1 MS/22/1 8 002200/sp1.lnh CC 11 MS/22/2/1 MS/22/2 8 002200/sp2.lnh DC 11 MS/22/3/1 MS/22/3 8 002200/sp3.lnh DC 11 MS/22/3/2 MS/22/4 8 002200/sp4.lnh DC 11 MS/22/3/3 MS/22/5 8 002300/sp0.lnh PDR 11 MS/23/1/1 MS/23/1 8 002300/sp1.lnh CC 11 MS/23/2/1 MS/23/2 8 002300/sp2.lnh DC 11 MS/23/3/1 MS/23/3 8 002300/sp3.lnh DC 11 MS/23/3/2 MS/23/4 8 002300/sp4.lnh DC 11 MS/23/3/3 MS/23/5 9 010600/sp0.lnh CC 11 ES-1/6/1/1 ES-1/6/1 9 010600/sp1.lnh DC 11 ES-1/6/2/1 ES-1/6/2 9 010600/sp2.lnh DC 11 ES-1/6/2/2 ES-1/6/3 9 010600/sp3.lnh DC 11 ES-1/6/2/3 ES-1/6/4 9 010600/sp4.lnh DC 11 ES-1/6/2/4 ES-1/6/5 9 010700/sp0.lnh CC 11 ES-1/7/1/1 ES-1/7/1 9 010700/sp1.lnh DC 11 ES-1/7/2/1 ES-1/7/2 9 010700/sp2.lnh DC 11 ES-1/7/2/2 ES-1/7/3 9 010700/sp3.lnh DC 11 ES-1/7/2/3 ES-1/7/4 9 010700/sp4.lnh DC 11 ES-1/7/2/4 ES-1/7/5 2 010800/sp0.lnh CC 11 ES-1/8/1/1 ES-1/8/1 2 010800/sp1.lnh DC 11 ES-1/8/2/1 ES-1/8/2 2 010800/sp2.lnh DC 11 ES-1/8/2/2 ES-1/8/3

2 010800/sp3.lnh DC 11 ES-1/8/2/3 ES-1/8/4 2 010800/sp4.lnh DC 11 ES-1/8/2/4 ES-1/8/5 2 010900/sp0.lnh CC 11 ES-1/9/1/1 ES-1/9/1 2 010900/sp1.lnh DC 11 ES-1/9/2/1 ES-1/9/2 2 010900/sp2.lnh DC 11 ES-1/9/2/2 ES-1/9/3 2 010900/sp3.lnh DC 11 ES-1/9/2/3 ES-1/9/4 2 010900/sp4.lnh DC 11 ES-1/9/2/4 ES-1/9/5 3 011000/sp0.lnh CC 11 ES-1/10/1/1 ES-1/10/1 3 011000/sp1.lnh DC 11 ES-1/10/2/1 ES-1/10/2 3 011000/sp2.lnh DC 11 ES-1/10/2/2 ES-1/10/3 3 011000/sp3.lnh DC 11 ES-1/10/2/3 ES-1/10/4 3 011000/sp4.lnh DC 11 ES-1/10/2/4 ES-1/10/5 3 011900/sp0.lnh CC 11 ES-1/19/1/1 ES-1/19/1 3 011900/sp1.lnh DC 11 ES-1/19/2/1 ES-1/19/2 3 011900/sp2.lnh DC 11 ES-1/19/2/2 ES-1/19/3 3 011900/sp3.lnh DC 11 ES-1/19/2/3 ES-1/19/4 3 011900/sp4.lnh DC 11 ES-1/19/2/4 ES-1/19/5 4 012000/sp0.lnh CC 11 ES-1/20/1/1 ES-1/20/1 4 012000/sp1.lnh DC 11 ES-1/20/2/1 ES-1/20/2 4 012000/sp2.lnh DC 11 ES-1/20/2/2 ES-1/20/3 4 012000/sp3.lnh DC 11 ES-1/20/2/3 ES-1/20/4 4 012000/sp4.lnh DC 11 ES-1/20/2/4 ES-1/20/5 4 012100/sp0.lnh CC 11 ES-1/21/1/1 ES-1/21/1 4 012100/sp1.lnh DC 11 ES-1/21/2/1 ES-1/21/2 4 012100/sp2.lnh DC 11 ES-1/21/2/2 ES-1/21/3 4 012100/sp3.lnh DC 11 ES-1/21/2/3 ES-1/21/4 4 012100/sp4.lnh DC 11 ES-1/21/2/4 ES-1/21/5 10 012200/sp0.lnh CC 11 ES-1/22/1/1 ES-1/22/1 10 012200/sp1.lnh DC 11 ES-1/22/2/1 ES-1/22/2 10 012200/sp2.lnh DC 11 ES-1/22/2/2 ES-1/22/3 10 012200/sp3.lnh DC 11 ES-1/22/2/3 ES-1/22/4 10 012200/sp4.lnh DC 11 ES-1/22/2/4 ES-1/22/5 10 012300/sp0.lnh CC 11 ES-1/23/1/1 ES-1/23/1 10 012300/sp1.lnh DC 11 ES-1/23/2/1 ES-1/23/2 10 012300/sp2.lnh DC 11 ES-1/23/2/2 ES-1/23/3 10 012300/sp3.lnh DC 11 ES-1/23/2/3 ES-1/23/4 10 012300/sp4.lnh DC 11 ES-1/23/2/4 ES-1/23/5 11 020600/sp0.lnh CC 11 ES-2/6/1/1 ES-2/6/1 11 020600/sp1.lnh DC 11 ES-2/6/2/1 ES-2/6/2 11 020600/sp2.lnh DC 11 ES-2/6/2/2 ES-2/6/3 11 020600/sp3.lnh DC 11 ES-2/6/2/3 ES-2/6/4 11 020600/sp4.lnh DC 11 ES-2/6/2/4 ES-2/6/5 11 020700/sp0.lnh CC 11 ES-2/7/1/1 ES-2/7/1 11 020700/sp1.lnh DC 11 ES-2/7/2/1 ES-2/7/2 11 020700/sp2.lnh DC 11 ES-2/7/2/2 ES-2/7/3 11 020700/sp3.lnh DC 11 ES-2/7/2/3 ES-2/7/4 11 020700/sp4.lnh DC 11 ES-2/7/2/4 ES-2/7/5 5 020800/sp0.lnh CC 11 ES-2/8/1/1 ES-2/8/1 5 020800/sp1.lnh DC 11 ES-2/8/2/1 ES-2/8/2 5 020800/sp2.lnh DC 11 ES-2/8/2/2 ES-2/8/3 5 020800/sp3.lnh DC 11 ES-2/8/2/3 ES-2/8/4 5 020800/sp4.lnh DC 11 ES-2/8/2/4 ES-2/8/5 5 020900/sp0.lnh CC 11 ES-2/9/1/1 ES-2/9/1 5 020900/sp1.lnh DC 11 ES-2/9/2/1 ES-2/9/2 5 020900/sp2.lnh DC 11 ES-2/9/2/2 ES-2/9/3 5 020900/sp3.lnh DC 11 ES-2/9/2/3 ES-2/9/4 5 020900/sp4.lnh DC 11 ES-2/9/2/4 ES-2/9/5 6 021000/sp0.lnh CC 11 ES-2/10/1/1 ES-2/10/1 6 021000/sp1.lnh DC 11 ES-2/10/2/1 ES-2/10/2 6 021000/sp2.lnh DC 11 ES-2/10/2/2 ES-2/10/3 6 021000/sp3.lnh DC 11 ES-2/10/2/3 ES-2/10/4 6 021000/sp4.lnh DC 11 ES-2/10/2/4 ES-2/10/5 6 021900/sp0.lnh CC 11 ES-2/19/1/1 ES-2/19/1 6 021900/sp1.lnh DC 11 ES-2/19/2/1 ES-2/19/2

6 021900/sp2.lnh DC 11 ES-2/19/2/2 ES-2/19/3 6 021900/sp3.lnh DC 11 ES-2/19/2/3 ES-2/19/4 6 021900/sp4.lnh DC 11 ES-2/19/2/4 ES-2/19/5 7 022000/sp0.lnh CC 11 ES-2/20/1/1 ES-2/20/1 7 022000/sp1.lnh DC 11 ES-2/20/2/1 ES-2/20/2 7 022000/sp2.lnh DC 11 ES-2/20/2/2 ES-2/20/3 7 022000/sp3.lnh DC 11 ES-2/20/2/3 ES-2/20/4 7 022000/sp4.lnh DC 11 ES-2/20/2/4 ES-2/20/5 7 022100/sp0.lnh CC 11 ES-2/21/1/1 ES-2/21/1 7 022100/sp1.lnh DC 11 ES-2/21/2/1 ES-2/21/2 7 022100/sp2.lnh DC 11 ES-2/21/2/2 ES-2/21/3 7 022100/sp3.lnh DC 11 ES-2/21/2/3 ES-2/21/4 7 022100/sp4.lnh DC 11 ES-2/21/2/4 ES-2/21/5 12 022200/sp0.lnh CC 11 ES-2/22/1/1 ES-2/22/1 12 022200/sp1.lnh DC 11 ES-2/22/2/1 ES-2/22/2 12 022200/sp2.lnh DC 11 ES-2/22/2/2 ES-2/22/3 12 022200/sp3.lnh DC 11 ES-2/22/2/3 ES-2/22/4 12 022200/sp4.lnh DC 11 ES-2/22/2/4 ES-2/22/5 12 022300/sp0.lnh CC 11 ES-2/23/1/1 ES-2/23/1 12 022300/sp1.lnh DC 11 ES-2/23/2/1 ES-2/23/2 12 022300/sp2.lnh DC 11 ES-2/23/2/2 ES-2/23/3 12 022300/sp3.lnh DC 11 ES-2/23/2/3 ES-2/23/4 12 022300/sp4.lnh DC 11 ES-2/23/2/4 ES-2/23/5 50 090600/sp0.lnh CC 11 ES-5/6/1/1 ES-5/6/1 50 090600/sp1.lnh DC 11 ES-5/6/2/1 ES-5/6/2 50 090600/sp2.lnh DC 11 ES-5/6/2/2 ES-5/6/3 50 090600/sp3.lnh DC 11 ES-5/6/2/3 ES-5/6/4 50 090600/sp4.lnh DC 11 ES-5/6/2/4 ES-5/6/5 50 090700/sp0.lnh CC 11 ES-5/7/1/1 ES-5/7/1 50 090700/sp1.lnh DC 11 ES-5/7/2/1 ES-5/7/2 50 090700/sp2.lnh DC 11 ES-5/7/2/2 ES-5/7/3 50 090700/sp3.lnh DC 11 ES-5/7/2/3 ES-5/7/4 50 090700/sp4.lnh DC 11 ES-5/7/2/4 ES-5/7/5 51 090800/sp0.lnh CC 11 ES-5/8/1/1 ES-5/8/1 51 090800/sp1.lnh DC 11 ES-5/8/2/1 ES-5/8/2 51 090800/sp2.lnh DC 11 ES-5/8/2/2 ES-5/8/3 51 090800/sp3.lnh DC 11 ES-5/8/2/3 ES-5/8/4 51 090800/sp4.lnh DC 11 ES-5/8/2/4 ES-5/8/5 51 090900/sp0.lnh CC 11 ES-5/9/1/1 ES-5/9/1 51 090900/sp1.lnh DC 11 ES-5/9/2/1 ES-5/9/2 51 090900/sp2.lnh DC 11 ES-5/9/2/2 ES-5/9/3 51 090900/sp3.lnh DC 11 ES-5/9/2/3 ES-5/9/4 51 090900/sp4.lnh DC 11 ES-5/9/2/4 ES-5/9/5 52 091000/sp0.lnh CC 11 ES-5/10/1/1 ES-5/10/1 52 091000/sp1.lnh DC 11 ES-5/10/2/1 ES-5/10/2 52 091000/sp2.lnh DC 11 ES-5/10/2/2 ES-5/10/3 52 091000/sp3.lnh DC 11 ES-5/10/2/3 ES-5/10/4 52 091000/sp4.lnh DC 11 ES-5/10/2/4 ES-5/10/5 52 091900/sp0.lnh CC 11 ES-5/19/1/1 ES-5/19/1 52 091900/sp1.lnh DC 11 ES-5/19/2/1 ES-5/19/2 52 091900/sp2.lnh DC 11 ES-5/19/2/2 ES-5/19/3 52 091900/sp3.lnh DC 11 ES-5/19/2/3 ES-5/19/4 52 091900/sp4.lnh DC 11 ES-5/19/2/4 ES-5/19/5 53 092000/sp0.lnh CC 11 ES-5/20/1/1 ES-5/20/1 53 092000/sp1.lnh DC 11 ES-5/20/2/1 ES-5/20/2 53 092000/sp2.lnh DC 11 ES-5/20/2/2 ES-5/20/3 53 092000/sp3.lnh DC 11 ES-5/20/2/3 ES-5/20/4 53 092000/sp4.lnh DC 11 ES-5/20/2/4 ES-5/20/5 53 092100/sp0.lnh CC 11 ES-5/21/1/1 ES-5/21/1 53 092100/sp1.lnh DC 11 ES-5/21/2/1 ES-5/21/2 53 092100/sp2.lnh DC 11 ES-5/21/2/2 ES-5/21/3 53 092100/sp3.lnh DC 11 ES-5/21/2/3 ES-5/21/4 53 092100/sp4.lnh DC 11 ES-5/21/2/4 ES-5/21/5 54 092200/sp0.lnh CC 11 ES-5/22/1/1 ES-5/22/1

54 092200/sp1.lnh DC 11 ES-5/22/2/1 ES-5/22/2 54 092200/sp2.lnh DC 11 ES-5/22/2/2 ES-5/22/3 54 092200/sp3.lnh DC 11 ES-5/22/2/3 ES-5/22/4 54 092200/sp4.lnh DC 11 ES-5/22/2/4 ES-5/22/5 54 092300/sp0.lnh CC 11 ES-5/23/1/1 ES-5/23/1 54 092300/sp1.lnh DC 11 ES-5/23/2/1 ES-5/23/2 54 092300/sp2.lnh DC 11 ES-5/23/2/2 ES-5/23/3 54 092300/sp3.lnh DC 11 ES-5/23/2/3 ES-5/23/4 54 092300/sp4.lnh DC 11 ES-5/23/2/4 ES-5/23/5 30 110600/sp0.lnh CC 11 ES-3/6/1/1 ES-3/6/1 30 110600/sp1.lnh DC 11 ES-3/6/2/1 ES-3/6/2 30 110600/sp2.lnh DC 11 ES-3/6/2/2 ES-3/6/3 30 110600/sp3.lnh DC 11 ES-3/6/2/3 ES-3/6/4 30 110600/sp4.lnh DC 11 ES-3/6/2/4 ES-3/6/5 30 110700/sp0.lnh CC 11 ES-3/7/1/1 ES-3/7/1 30 110700/sp1.lnh DC 11 ES-3/7/2/1 ES-3/7/2 30 110700/sp2.lnh DC 11 ES-3/7/2/2 ES-3/7/3 30 110700/sp3.lnh DC 11 ES-3/7/2/3 ES-3/7/4 30 110700/sp4.lnh DC 11 ES-3/7/2/4 ES-3/7/5 31 110800/sp0.lnh CC 11 ES-3/8/1/1 ES-3/8/1 31 110800/sp1.lnh DC 11 ES-3/8/2/1 ES-3/8/2 31 110800/sp2.lnh DC 11 ES-3/8/2/2 ES-3/8/3 31 110800/sp3.lnh DC 11 ES-3/8/2/3 ES-3/8/4 31 110800/sp4.lnh DC 11 ES-3/8/2/4 ES-3/8/5 31 110900/sp0.lnh CC 11 ES-3/9/1/1 ES-3/9/1 31 110900/sp1.lnh DC 11 ES-3/9/2/1 ES-3/9/2 31 110900/sp2.lnh DC 11 ES-3/9/2/2 ES-3/9/3 31 110900/sp3.lnh DC 11 ES-3/9/2/3 ES-3/9/4 31 110900/sp4.lnh DC 11 ES-3/9/2/4 ES-3/9/5 32 111000/sp0.lnh CC 11 ES-3/10/1/1 ES-3/10/1 32 111000/sp1.lnh DC 11 ES-3/10/2/1 ES-3/10/2 32 111000/sp2.lnh DC 11 ES-3/10/2/2 ES-3/10/3 32 111000/sp3.lnh DC 11 ES-3/10/2/3 ES-3/10/4 32 111000/sp4.lnh DC 11 ES-3/10/2/4 ES-3/10/5 32 111900/sp0.lnh CC 11 ES-3/19/1/1 ES-3/19/1 32 111900/sp1.lnh DC 11 ES-3/19/2/1 ES-3/19/2 32 111900/sp2.lnh DC 11 ES-3/19/2/2 ES-3/19/3 32 111900/sp3.lnh DC 11 ES-3/19/2/3 ES-3/19/4 32 111900/sp4.lnh DC 11 ES-3/19/2/4 ES-3/19/5 33 112000/sp0.lnh CC 11 ES-3/20/1/1 ES-3/20/1 33 112000/sp1.lnh DC 11 ES-3/20/2/1 ES-3/20/2 33 112000/sp2.lnh DC 11 ES-3/20/2/2 ES-3/20/3 33 112000/sp3.lnh DC 11 ES-3/20/2/3 ES-3/20/4 33 112000/sp4.lnh DC 11 ES-3/20/2/4 ES-3/20/5 33 112100/sp0.lnh CC 11 ES-3/21/1/1 ES-3/21/1 33 112100/sp1.lnh DC 11 ES-3/21/2/1 ES-3/21/2 33 112100/sp2.lnh DC 11 ES-3/21/2/2 ES-3/21/3 33 112100/sp3.lnh DC 11 ES-3/21/2/3 ES-3/21/4 33 112100/sp4.lnh DC 11 ES-3/21/2/4 ES-3/21/5 34 112200/sp0.lnh CC 11 ES-3/22/1/1 ES-3/22/1 34 112200/sp1.lnh DC 11 ES-3/22/2/1 ES-3/22/2 34 112200/sp2.lnh DC 11 ES-3/22/2/2 ES-3/22/3 34 112200/sp3.lnh DC 11 ES-3/22/2/3 ES-3/22/4 34 112200/sp4.lnh DC 11 ES-3/22/2/4 ES-3/22/5 34 112300/sp0.lnh CC 11 ES-3/23/1/1 ES-3/23/1 34 112300/sp1.lnh DC 11 ES-3/23/2/1 ES-3/23/2 34 112300/sp2.lnh DC 11 ES-3/23/2/2 ES-3/23/3 34 112300/sp3.lnh DC 11 ES-3/23/2/3 ES-3/23/4 34 112300/sp4.lnh DC 11 ES-3/23/2/4 ES-3/23/5 40 120600/sp0.lnh CC 11 ES-4/6/1/1 ES-4/6/1 40 120600/sp1.lnh DC 11 ES-4/6/2/1 ES-4/6/2 40 120600/sp2.lnh DC 11 ES-4/6/2/2 ES-4/6/3 40 120600/sp3.lnh DC 11 ES-4/6/2/3 ES-4/6/4 40 120600/sp4.lnh DC 11 ES-4/6/2/4 ES-4/6/5

40 120700/sp0.lnh CC 11 ES-4/7/1/1 ES-4/7/1 40 120700/sp1.lnh DC 11 ES-4/7/2/1 ES-4/7/2 40 120700/sp2.lnh DC 11 ES-4/7/2/2 ES-4/7/3 40 120700/sp3.lnh DC 11 ES-4/7/2/3 ES-4/7/4 40 120700/sp4.lnh DC 11 ES-4/7/2/4 ES-4/7/5 41 120800/sp0.lnh CC 11 ES-4/8/1/1 ES-4/8/1 41 120800/sp1.lnh DC 11 ES-4/8/2/1 ES-4/8/2 41 120800/sp2.lnh DC 11 ES-4/8/2/2 ES-4/8/3 41 120800/sp3.lnh DC 11 ES-4/8/2/3 ES-4/8/4 41 120800/sp4.lnh DC 11 ES-4/8/2/4 ES-4/8/5 41 120900/sp0.lnh CC 11 ES-4/9/1/1 ES-4/9/1 41 120900/sp1.lnh DC 11 ES-4/9/2/1 ES-4/9/2 41 120900/sp2.lnh DC 11 ES-4/9/2/2 ES-4/9/3 41 120900/sp3.lnh DC 11 ES-4/9/2/3 ES-4/9/4 41 120900/sp4.lnh DC 11 ES-4/9/2/4 ES-4/9/5 42 121000/sp0.lnh CC 11 ES-4/10/1/1 ES-4/10/1 42 121000/sp1.lnh DC 11 ES-4/10/2/1 ES-4/10/2 42 121000/sp2.lnh DC 11 ES-4/10/2/2 ES-4/10/3 42 121000/sp3.lnh DC 11 ES-4/10/2/3 ES-4/10/4 42 121000/sp4.lnh DC 11 ES-4/10/2/4 ES-4/10/5 42 121900/sp0.lnh CC 11 ES-4/19/1/1 ES-4/19/1 42 121900/sp1.lnh DC 11 ES-4/19/2/1 ES-4/19/2 42 121900/sp2.lnh DC 11 ES-4/19/2/2 ES-4/19/3 42 121900/sp3.lnh DC 11 ES-4/19/2/3 ES-4/19/4 42 121900/sp4.lnh DC 11 ES-4/19/2/4 ES-4/19/5 43 122000/sp0.lnh CC 11 ES-4/20/1/1 ES-4/20/1 43 122000/sp1.lnh DC 11 ES-4/20/2/1 ES-4/20/2 43 122000/sp2.lnh DC 11 ES-4/20/2/2 ES-4/20/3 43 122000/sp3.lnh DC 11 ES-4/20/2/3 ES-4/20/4 43 122000/sp4.lnh DC 11 ES-4/20/2/4 ES-4/20/5 43 122100/sp0.lnh CC 11 ES-4/21/1/1 ES-4/21/1 43 122100/sp1.lnh DC 11 ES-4/21/2/1 ES-4/21/2 43 122100/sp2.lnh DC 11 ES-4/21/2/2 ES-4/21/3 43 122100/sp3.lnh DC 11 ES-4/21/2/3 ES-4/21/4 43 122100/sp4.lnh DC 11 ES-4/21/2/4 ES-4/21/5 44 122200/sp0.lnh CC 11 ES-4/22/1/1 ES-4/22/1 44 122200/sp1.lnh DC 11 ES-4/22/2/1 ES-4/22/2 44 122200/sp2.lnh DC 11 ES-4/22/2/2 ES-4/22/3 44 122200/sp3.lnh DC 11 ES-4/22/2/3 ES-4/22/4 44 122200/sp4.lnh DC 11 ES-4/22/2/4 ES-4/22/5 44 122300/sp0.lnh CC 11 ES-4/23/1/1 ES-4/23/1 44 122300/sp1.lnh DC 11 ES-4/23/2/1 ES-4/23/2 44 122300/sp2.lnh DC 11 ES-4/23/2/2 ES-4/23/3 44 122300/sp3.lnh DC 11 ES-4/23/2/3 ES-4/23/4 44 122300/sp4.lnh DC 11 ES-4/23/2/4 ES-4/23/5 --------------------------------------------------------------------------- Following 0 devices are down: --------------------------------------------------------------------------- DEVICE STATE MOD LNH TYPE DEV/SPM DEV-ID SPM-ID --------------------------------------------------------------------------- Following 0 devices are hanging and require an spm restart: Spm can be restarted with command: acc <lnh> restart. E.g: acc 001900/sp0.lnh restart --------------------------------------------------------------------------- DEVICE STATE MOD LNH TYPE DEV/SPM DEV-ID SPM-ID --------------------------------------------------------------------------- Summary:

------------------------------------------------------------------------------------DevType Up Tot % Mod1 Mod2 Mod3 Mod4 Mod5 Mod6 Mod7 Mod8 Mod9 Mod10 Mod11 Mod12 Mod30 Mod31 Mod32 Mod33 Mod34 Mod40 Mod41 Mod42 Mod43 Mod44 Mod50 Mod51 Mod52 Mod53 Mod54 ------------------------------------------------------------------------------------PDR 5 5 100.0% 100% 0% 0% 0% 0% 0% 0% 100% 0% 0% 0% 0% 0% 0% 0% 0% 0% 0% 0% 0% 0% 0% 0% 0% 0% 0% 0% CC 55 55 100.0% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% DC 215 215 100.0% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100%

APPENDIX F: WHEN RBS CONNECT TO RNC VIA TELLAB AGGREGATOR /* NodeB GRY404 went down due to microwave fault. E1 is down */ 3RR01> alt 070701-15:04:25 172.24.12.207 7.0 RESTRICTED RNC_NODE_MODEL_F_5_2 stopfile=/tmp/19941 Trying file=/home/zm814584/moshell_logfiles/logs_moshell/tempfiles/20070701-120649_19917/ior19917 Resolving the alarm service in OMS... Simple Alarm Client initialized... Starting to retrieve active alarms Nr of active alarms are: 10 ====================================================================================Date & Time (Local) S Specific Problem Cause Mo-Reference ====================================================================================2007-07-01 14:15:00 M NbapDedicated_RncRbsControlLinkDown transmission_error IubLink=Iub_GRY404,NbapDedicated=1 2007-07-01 14:37:46 M UtranCell_ServiceUnavailable unavailable UtranCell=GRY404C 2007-07-01 14:37:46 M UtranCell_ServiceUnavailable unavailable UtranCell=GRY404B 2007-07-01 14:37:47 M UtranCell_ServiceUnavailable unavailable UtranCell=GRY404A >>> Total: 10 Alarms (0 Critical, 9 Major) 3RR01> lt ^utrancell|iub|atm|aal|atm 3RR01> lcc gry404 3RR01> lst gry404 070701-14:37:33 172.24.12.207 7.0 RESTRICTED RNC_NODE_MODEL_F_5_2 stopfile=/tmp/19941 =================================================================================== Proxy Adm State Op. State MO =================================================================================== 3456 1 (ENABLED) RncFunction=1,IubLink=Iub_GRY404 3601 1 (UNLOCKED) 0 (DISABLED) RncFunction=1,UtranCell=GRY404C 3602 1 (UNLOCKED) 0 (DISABLED) RncFunction=1,UtranCell=GRY404B 3603 1 (UNLOCKED) 0 (DISABLED) RncFunction=1,UtranCell=GRY404A 3856 1 (UNLOCKED) 1 (ENABLED) RncFunction=1,IubLink=Iub_GRY404,NodeSynchTp=2 3857 1 (UNLOCKED) 1 (ENABLED) RncFunction=1,IubLink=Iub_GRY404,NodeSynchTp=1 3858 1 (UNLOCKED) 0 (DISABLED) RncFunction=1,IubLink=Iub_GRY404,NbapDedicated=1 3859 1 (UNLOCKED) 0 (DISABLED) RncFunction=1,IubLink=Iub_GRY404,NbapCommon=1 3861 1 (UNLOCKED) 0 (DISABLED) RncFunction=1,UtranCell=GRY404C,Fach=1 3866 1 (UNLOCKED) 0 (DISABLED) RncFunction=1,UtranCell=GRY404C,Rach=1 3867 1 (UNLOCKED) 0 (DISABLED) RncFunction=1,UtranCell=GRY404C,Hsdsch=1 3868 1 (UNLOCKED) 0 (DISABLED) RncFunction=1,UtranCell=GRY404C,Pch=1

3881 1 (UNLOCKED) 0 (DISABLED) RncFunction=1,UtranCell=GRY404B,Rach=1 3895 1 (UNLOCKED) 0 (DISABLED) RncFunction=1,UtranCell=GRY404B,Hsdsch=1 3903 1 (UNLOCKED) 0 (DISABLED) RncFunction=1,UtranCell=GRY404B,Fach=1 3904 1 (UNLOCKED) 0 (DISABLED) RncFunction=1,UtranCell=GRY404B,Pch=1 3931 1 (UNLOCKED) 0 (DISABLED) RncFunction=1,UtranCell=GRY404A,Rach=1 3938 1 (UNLOCKED) 0 (DISABLED) RncFunction=1,UtranCell=GRY404A,Fach=1 3942 1 (UNLOCKED) 0 (DISABLED) RncFunction=1,UtranCell=GRY404A,Hsdsch=1 3943 1 (UNLOCKED) 0 (DISABLED) RncFunction=1,UtranCell=GRY404A,Pch=1 =================================================================================== Total: 20 MOs 3RR01> get 3858 ====================================================================================3858 RncFunction=1,IubLink=Iub_GRY404,NbapDedicated=1 ====================================================================================NbapDedicatedId 1 activeUniSaalTpRef UniSaalTp=b1019da administrativeState 1 (UNLOCKED) availabilityStatus 2 (FAILED) l2EstablishReqRetryT 5 operationalState 0 (DISABLED) standbyUniSaalTpRef UniSaalTp=b1019db userLabel 1 ==================================================================================== 3RR01> lst b1019 =================================================================================== Proxy Adm State Op. State MO =================================================================================== 4428 1 (UNLOCKED) 1 (ENABLED) TransportNetwork=1,Aal2PathVccTp=b1019a4 4429 1 (UNLOCKED) 1 (ENABLED) TransportNetwork=1,Aal2PathVccTp=b1019a3 4430 1 (UNLOCKED) 1 (ENABLED) TransportNetwork=1,Aal2PathVccTp=b1019a2 4431 1 (UNLOCKED) 1 (ENABLED) TransportNetwork=1,Aal2PathVccTp=b1019a1 4824 1 (ENABLED) TransportNetwork=1,Aal5TpVccTp=b1019qb 4825 1 (ENABLED) TransportNetwork=1,Aal5TpVccTp=b1019qa 4830 1 (ENABLED) TransportNetwork=1,Aal5TpVccTp=b1019db 4831 1 (ENABLED) TransportNetwork=1,Aal5TpVccTp=b1019da 4832 1 (ENABLED) TransportNetwork=1,Aal5TpVccTp=b1019cb 4833 1 (ENABLED) TransportNetwork=1,Aal5TpVccTp=b1019ca 5549 1 (ENABLED) TransportNetwork=1,Aal0TpVccTp=b1019sb1 5550 1 (ENABLED) TransportNetwork=1,Aal0TpVccTp=b1019sa1 5769 0 (DISABLED) TransportNetwork=1,Aal2Sp=1,Aal2Ap=b1019 6050 1 (ENABLED) TransportNetwork=1,UniSaalTp=b1019qb 6051 1 (ENABLED) TransportNetwork=1,UniSaalTp=b1019qa 6056 1 (ENABLED) TransportNetwork=1,UniSaalTp=b1019db 6057 1 (ENABLED) TransportNetwork=1,UniSaalTp=b1019da 6058 1 (ENABLED) TransportNetwork=1,UniSaalTp=b1019cb 6059 1 (ENABLED) TransportNetwork=1,UniSaalTp=b1019ca 6769 1 (ENABLED) TransportNetwork=1,AtmCrossConnection=b1019ib 6770 1 (ENABLED) TransportNetwork=1,AtmCrossConnection=b1019ia =================================================================================== Total: 21 MOs 3RR01> get 6769 ====================================================================================6769 TransportNetwork=1,AtmCrossConnection=b1019ib ====================================================================================AtmCrossConnectionId b1019ib operationalState 1 (ENABLED) userLabel b1019ib vclTpAId AtmPort=MS-7-2,VplTp=vp21,VpcTp=1,VclTp=vc10019

vclTpBId AtmPort=ES-5-26-2,VplTp=vp51,VpcTp=1,VclTp=vc1233 ==================================================================================== 3RR01> get 4428 ====================================================================================4428 TransportNetwork=1,Aal2PathVccTp=b1019a4 ====================================================================================Aal2PathVccTpId b1019a4 aal2PathId 4 aal2PathOwner true aal2QoSAvailableProfiles 4 (CLASS_C) aal2QoSProfileId Aal2QosProfile=ad10bd20 administrativeState 1 (UNLOCKED) alarmReport 2 (ALARM_LOC) availabilityStatus 0 (NO_STATUS) continuityCheck false counterMode 0 (PM_MODE_OFF) nomPmBlocksize 1024 (NOM_PM_BLKSIZE_2_10) operationalState 1 (ENABLED) remoteBlockingState 1 (REMOTELY_UNBLOCKED) reservedBy Aal2Sp=1,Aal2Ap=b1019,Aal2PathDistributionUnit=1 timerCu 10 userLabel b1019a4 vclTpId AtmPort=ES-5-26-2,VplTp=vp51,VpcTp=1,VclTp=vc1247 ====================================================================================Total: 1 MOs 3RR01> lget b1019 vcltp ====================================================================================MO Attribute Value ====================================================================================Aal2PathVccTp=b1019a4 vclTpId AtmPort=ES-5-26-2,VplTp=vp51,VpcTp=1,VclTp=vc1247 Aal2PathVccTp=b1019a3 vclTpId AtmPort=ES-5-2-2,VplTp=vp51,VpcTp=1,VclTp=vc1246 Aal2PathVccTp=b1019a2 vclTpId AtmPort=ES-5-26-2,VplTp=vp51,VpcTp=1,VclTp=vc1240 Aal2PathVccTp=b1019a1 vclTpId AtmPort=ES-5-2-2,VplTp=vp51,VpcTp=1,VclTp=vc1239 Aal5TpVccTp=b1019qb vclTpId AtmPort=ES-5-26-2,VplTp=vp51,VpcTp=1,VclTp=vc1245 Aal5TpVccTp=b1019qa vclTpId AtmPort=ES-5-2-2,VplTp=vp51,VpcTp=1,VclTp=vc1238 Aal5TpVccTp=b1019db vclTpId AtmPort=ES-5-26-2,VplTp=vp51,VpcTp=1,VclTp=vc1244 Aal5TpVccTp=b1019da vclTpId AtmPort=ES-5-2-2,VplTp=vp51,VpcTp=1,VclTp=vc1237 Aal5TpVccTp=b1019cb vclTpId AtmPort=ES-5-26-2,VplTp=vp51,VpcTp=1,VclTp=vc1243 Aal5TpVccTp=b1019ca vclTpId AtmPort=ES-5-2-2,VplTp=vp51,VpcTp=1,VclTp=vc1236 Aal0TpVccTp=b1019sb1 vclTpId AtmPort=ES-5-26-2,VplTp=vp51,VpcTp=1,VclTp=vc1235 Aal0TpVccTp=b1019sa1 vclTpId AtmPort=ES-5-2-2,VplTp=vp51,VpcTp=1,VclTp=vc1234 AtmCrossConnection=b1019ib vclTpAId AtmPort=MS-7-2,VplTp=vp21,VpcTp=1,VclTp=vc10019 AtmCrossConnection=b1019ib vclTpBId AtmPort=ES-5-26-2,VplTp=vp51,VpcTp=1,VclTp=vc1233 AtmCrossConnection=b1019ia vclTpAId AtmPort=MS-6-1,VplTp=vp20,VpcTp=1,VclTp=vc10019 AtmCrossConnection=b1019ia vclTpBId AtmPort=ES-5-2-2,VplTp=vp51,VpcTp=1,VclTp=vc1232 ==================================================================================== 1

Moshell CMD

Documents

Transcript of Moshell CMD