Modular Scaffold MEKA 48 - DACAME · The Modular Scaffold MEKA 48 is designed to adapt to the most...
Transcript of Modular Scaffold MEKA 48 - DACAME · The Modular Scaffold MEKA 48 is designed to adapt to the most...
MEKA 48
NA
Modular ScaffoldIMpErIAl uNIts
MODULAR SCAFFOLD
2 DACAME
MEKA 48
A34/000022
The Modular Scaffold MEKA 48 is designed to adapt to the most complex scaffold structures. Its versatility offers a wide range of uses, a significant load-bearing capacity and unparalleled quick assembly of all its components. Incorporates a safety rail.
The Modular Scaffold MEKA 48 is based on a system of standards with rosettes allowing up to 8 connections where the ledgers and diagonal braces connect, and enable different angles to be made every 1’ 7.7” (50 cm).
MODULAR SCAFFOLD
The Modular Scaffolding MEKA 48 is manufactured according to European standards:• EN 12810 • EN 12811
Technical specifications: Steel tube Ø 1.9” (48.3 mm) Grade St-44. All com-ponents are galvanized and have a minimum thickness of 75 microns, ac-cording to the European Standard EN 1461.
MEKA 48
3DACAME
MODULAR SCAFFOLD
4 DACAME
MEKA 48
5DACAME
MODULAR SCAFFOLD
6 DACAME
NOMENCLATURE
2
3
7
9
10
11
12
14
15
16
17
18
19
20
IDENTIFyING ThE COMpONENTS: 1.- SCREW JACK bASE 2.- SIDE bRACKET 3.- JACK 4.- bASE COLLAR 5.- VERTICAL STANDARD 6.- ASSEMbLy GUARDRAIL 7.- GUARDRAIL 8.- SIDE GUARDRAIL 9.- DIAGONAL bRACE10.- LEDGER11.- TRUSS LEDGER12.- SpIGOT WITh CLAMp
13.- DOUbLE TRUSS LEDGER14.- FIXED STEEL pLANK15.- ACCESS pLANK16.- ACCESS LADDER17.- TOEbOARD18.- bRACKET19.- TIE bAR20.- pROVISIONAL GUARDRAIL21.- pROTECTION FAN22.- ACCESS STEpS23.- OUTER GUARDRAIL24.- INNER GUARDRAIL
MEKA 48
7DACAME
1
4
5
6
8
13
21
22
23
24
9
MODULAR SCAFFOLD
8 DACAME
SCREW JACK bASES
SWIVEL SCREW JACK bASE
REINFORCED SIDE bRACKET
bASE COLLAR
Made of zinc plated steel. They bear the load of the standards. The reinforced base plate has a thickness of 0.2” (5 mm) and a surface area of 4.72”x 4.72” (120 X 120 mm). Ø 1.42” (36 mm) threaded rod available in different lengths.With overlapping space to comply with the relevant regulation.
The screw jack base 1.0 m · 2 levers is pre-eminently used to stabilize the structure.
Accommodates the scaffold on inclined surfaces.
The reinforced side bracket is man-ufactured with hot galvanized steel. Allows for the scaffold to be erected to a wall or a facade, using either chemical or mechanical anchoring methods. It has a reinforced base plate with 6 Ø 0.8” (20 mm) con-nection holes for assembly purpos-es.Length of console: 4’ 3.2” (1.3 m).The screw jack 0.5 m with clamp Ø 1.89” allows the selected scaffold-ing system to be erected on the wall brace.
Manufactured with hot galvanized steel. Always attached to the screw jacks. The rosette allows the scaffolding to be erected.
part No. Description height Max. Reg. Weight
025010108 SCREW JACK bASE 0.5 m 1' 7.7" 1' 1.8" 5.7 lbs.
025020078 SCREW JACK bASE 0.75 m 2' 5.5" 1' 10.4" 7.5 lbs.
025020108 SCREW JACK bASE 1.0 m 3' 3.4" 2' 5.5" 9.5 lbs.
025020118 SCREW JACK bASE 1.0 m 2 levers 3' 3.4" 3' 3.4" 10.6 lbs.
part No. Description Max. Reg. Weight
219903130 REINFORCED SIDE bRACKET 1.3 m 4' 3.2" 37.4 lbs.
219904050 SCREW JACK 0.5 m CLAMp Ø 48 mm 1’ 1.8” 5.1 lbs.
part No. Description Max. Reg. Weight
219900010 bASE COLLAR MEKA 48 · 0.3 m (GA) 11.8” 3.3 lbs.
part No. Description height Max. Reg. Weight
219902060 SWIVEL JACK bASE 0.6 m 1’ 11.6” 1’ 7.7” 7.0 lbs.
MEKA 48
9DACAME
VERTICAL STANDARDS
LEDGERS
Manufactured with tubes of Ø 1.9” x 0.13” (Ø48.3 x 3.2 mm) thickness, comprising rosettes at intervals of 1’ 7.7” (50 cm). Each rosette has 4 small openings for connecting braces and 4 big openings for connecting diagonal braces. They bear the load of the scaffolding. Galvanized and with a minimum thickness of 75 microns. The upper end has a spigot for attaching Ø 1’ 3.7” (Ø 40 mm) pipes. Every standard has connection holes at its lower end and in the spigot, and therefore both components can be joined together with a snap pin.
Couplingpin
Rosette
Lowerendhole
Snappin
Assembly
Ledger lock
part No. Description height Weight
210100050 STANDARD MEKA 48 · 0.5 m (GA) 1' 7.7" 6.6 lbs.
210100100 STANDARD MEKA 48 · 1.0 m (GA) 3' 3.4" 11.5 lbs.
210100200 STANDARD MEKA 48 · 2.0 m (GA) 6' 6.7" 21.1 lbs.
210100300 STANDARD MEKA 48 · 3.0 m (GA) 9' 10.1" 31.3 lbs.
070300001 SNAp pIN - 0.2 lbs.
part No. Description Length Weight
210200040 LEDGER MEKA 48 · 0.4 m (GA) 1' 3.7" 4.2 lbs.
210200070 LEDGER MEKA 48 · 0.7 m (GA) 2' 3.6" 7.7 lbs.
210200100 LEDGER MEKA 48 · 1.0 m (GA) 3' 3.4" 9.9 lbs.
210200130 LEDGER MEKA 48 · 1.3 m (GA) 4' 3.2" 12.3 lbs.
210200150 LEDGER MEKA 48 · 1.5 m (GA) 4' 11.1" 13.2 lbs.
210200200 LEDGER MEKA 48 · 2.0 m (GA) 6' 6.7" 18.3 lbs.
210200230 LEDGER MEKA 48 · 2.3 m (GA) 7' 6.6" 20.7 lbs.
210200250 LEDGER MEKA 48 · 2.5 m (GA) 8' 2.4" 22.9 lbs.
210200300 LEDGER MEKA 48 · 3.0 m (GA) 9' 10.1" 25.1 lbs.
Manufactured with Ø 1.9” (48.3 mm) pipe, they have locks with cone-shaped wedges on both ends that can be inserted into the small rosette openings. hot galvanized and with a minimum thickness of 75 microns. They fulfill the duties of a guardrail (erected 1’ 7.7” (0.5 m) and 3’ 3.4” (1 m) above the planks) and also support the platforms.
MODULAR SCAFFOLD
10 DACAME
ASSEMbLy GUARDRAILS
GUARDRAILS
SIDE GUARDRAILS
SIDE pROTECTION
Manufactured with Ø 1.38” (35 mm) pipe, it is designed for assembly on the lower level of the scaffolding, providing the fitter with security during the assembly process through its fixed guardrail. Hot galvanized and with a minimum thickness of 75 microns. Avoids the use of diagonal braces for lower-standing operations by securing the structure through 4 points (2 locks and 2 hooks).
Manufactured with Ø 1.9” (48.3 mm) pipes, they allow faster and lighter assemblies. hot galvanized and with a minimum thickness of 75 microns. protective bar consisting of Ø a 0.98” (25 mm) pipe standing at 0.5 m.
Manufactured with Ø 1.26” (32 mm) pipe, they have a lock on one end and a hook on the other to allow quick assemblies.
hook(upper section)
Ledger lock(lower section)
The modular scaffolding MEKA 48 system offers various side protection possibilities to meet the specific requirements of each scaffolding: .1) Ledgers 2) Standard and side guardrails 3) Assembly guardrails
- The number of necessary items is reduced.
- Quick assembly. - The highest safety measures are now incorporated into the system.
- A provisional assembly guardrail ensures safety during the assembly process.
- A provisional assembly guardrail ensures safety during the assembly process.
- Avoids the need to use diagonal braces on low standing scaffolding structures.
part No. Description Length Weight
211710200 ASSEMbLy GUARDRAIL M 48 · 2.0 m (GA) 6' 6.7" 26.7 lbs.
211710250 ASSEMbLy GUARDRAIL M 48 · 2.5 m (GA) 8' 2.4" 29.7 lbs.
211710300 ASSEMbLy GUARDRAIL M 48 · 3.0 m (GA) 9' 10.1" 32.6 lbs.
part No. Description Length Weight
211720200 GUARDRAIL MEKA 48 · 2.0 m (GA) 6' 6.7" 17.4 lbs.
211720250 GUARDRAIL MEKA 48 · 2.5 m (GA) 8' 2.4" 22.0 lbs.
211720300 GUARDRAIL MEKA 48 · 3.0 m (GA) 9' 10.1" 24.7 lbs.
part No. Description Length Weight
211730070 SIDE GUARDRAIL MEKA 48 · 0.7 m (GA) 2' 3.6" 6.8 lbs.
211730100 SIDE GUARDRAIL MEKA 48 · 1.0 m (GA) 3' 3.4" 8.4 lbs.
MEKA 48
11DACAME
DIAGONAL bRACES
RUNNERS
part No. COMpONENT h M Length Weight
210315070 DIAGONAL MEKA 48 h·1.5x0.7 m (GA) 4' 11.1" 2' 3.6" 5' 4.2" 16.3 lbs.
210315100 DIAGONAL MEKA 48 h·1.5x1.0 m (GA) 4' 11.1" 3' 3.4" 5' 8.9" 18.9 lbs.
210320100 DIAGONAL MEKA 48 h·2.0x1.0 m (GA) 6' 6.7" 3' 3.4" 7' 3" 19.8 lbs.
210320130 DIAGONAL MEKA 48 h·2.0x1.3 m (GA) 6' 6.7" 4' 3.2" 7' 8.1" 23.1 lbs.
210320150 DIAGONAL MEKA 48 h·2.0x1.5 m (GA) 6' 6.7" 4' 11.1" 8' 0.1" 24.7 lbs.
210320200 DIAGONAL MEKA 48 h·2.0x2.0 m (GA) 6' 6.7" 6' 6.7" 9' 0.3" 25.6 lbs.
210320250 DIAGONAL MEKA 48 h·2.0x2.5 m (GA) 6' 6.7" 8' 2.4" 10' 2" 30.4 lbs.
210320300 DIAGONAL MEKA 48 h·2.0x3.0 m (GA) 6' 6.7" 9' 10.1" 11' 5.8" 33.0 lbs.
Manufactured with Ø 1.9” (48.3 mm) pipe, they have articulated locks on both ends. They stiffen the standards and the ledgers that make up the vertical structure.
Manufactured with Ø 1.9” (48.3 mm) pipe, they have 2 clamps for attaching the Ø 1.9” (48.3 mm) pipes. They are used in order to offer plank support for scaffoldings using trusses.
SpIGOT WITh CLAMp
Allows standards to be assembled on ledgers, reinforced beams or trusses, through the use of a clamp that can be attached to a Ø 1.9” (48.3 mm) pipe. The spigot contains holes so a snap pin can be attached when necessary.
EXAMpLE OF USE:• RUNNER• SpIGOT WITh CLAMp
L
M
h
part No. Description Length Weight
025029069 RUNNER 0.7 m (GA) 2' 3.6" 7.5 lbs.
025029079 RUNNER 1.0 m (GA) 3' 3.4" 10.6 lbs.
part No. Description Length Weight
219900020 SpIGOT WITh CLAMp MEKA 48 (GA) 3.9” 3.3 lbs.
MODULAR SCAFFOLD
12 DACAME
TRUSS LEDGERS
Much like the ledger, the truss ledger channels the standards load towards the rosettes. The main difference lies in its loading capacity, increased thanks to the gussets and the lower horizontal pipe, making it more resistant to bend.
DOUbLE TRUSS LEDGERS
Manufactured with Ø 1.9” (48.3 mm) steel pipe and solid rectangular gussets, there are 4 locks welded to the ends. The truss is 1’ 7.7” (50 cm) in height. It can cope with heavy loads.
EXAMpLES OF USE:• DOUbLE TRUSS LEDGERS - bRIDGE• TRUSS LEDGERS - MObILE TOWER
1’ 7.7”
part No. Description Length Weight
211000100 TRUSS LEDGER MEKA 48 · 1.0 m (GA) 3' 3.4" 16.5 lbs.
211000130 TRUSS LEDGER MEKA 48 · 1.3 m (GA) 4' 3.2" 22.2 lbs.
211000150 TRUSS LEDGER MEKA 48 · 1.5 m (GA) 4' 11.1" 25.3 lbs.
211000200 TRUSS LEDGER MEKA 48 · 2.0 m (GA) 6' 6.7" 34.6 lbs.
211000250 TRUSS LEDGER MEKA 48 · 2.5 m (GA) 8' 2.4" 45.2 lbs.
211000300 TRUSS LEDGER MEKA 48 · 3.0 m (GA) 9' 10.1" 54.0 lbs.
part No. Description Length Weight
211100200 DOUbLE TRUSS LEDGER M 48 · 2.0 m (GA) 6' 6.7" 63.9 lbs.
211100300 DOUbLE TRUSS LEDGER M 48 · 3.0 m (GA) 9' 10.1" 94.7 lbs.
211100400 DOUbLE TRUSS LEDGER M 48 · 4.0 m (GA) 13' 1.5" 116.7 lbs.
211100500 DOUbLE TRUSS LEDGER M 48 · 5.0 m (GA) 16' 4.9" 152.0 lbs.
211100600 DOUbLE TRUSS LEDGER M 48 · 6.0 m (GA) 19' 8.2" 169.6 lbs.
MEKA 48
13DACAME
ALUMINUM DOUbLE TRUSS LEDGERS SySTEMS
ALUMINUM DOUbLE TRUSS LEDGERSManufactured with Ø 1,89”x0.16” (48x4 mm) aluminum pipe, their distinguishing features are their lightweight and ease handling. 2 and 3 m models are available.Through the steel fittings between the truss-es and the ends, the system can cover a wide range of lengths.
CENTRAL FITTING
Manufactured with Ø 1.5” (38 mm) steel pipe, it ensures that the trusses are securely hold together thanks to the 12 M12 (0.47”) screws and nuts. Galvanized.
END FITTING MEKA 48 Manufactured with Ø 1.5” (38 mm) steel pipe, it attaches the truss to the standards' rosettes using 2 locks. The truss is secured using 6 M12 (0.47”) screws and nuts. Galvanized.
ASSEMbLy EXAMpLE:• ALUMINUM DOUbLE TRUSS LEDGER 2m• ALUMINUM DOUbLE TRUSS LEDGER 3m• CENTRAL FITTING• END FITTING MEKA 48 (2 UNITS)
IDENTIFyING ThE COMpONENTS: 1. ALUMINUM DOUbLE TRUSS LEDGER 2m2. ALUMINUM DOUbLE TRUSS LEDGER 3m3. CENTRAL FITTING4. END FITTING MEKA 485. M12 SCREWS + NUTS
8’ 11.9”
5’ 8.5”
1’ 0.6”
2’ 7.5”
9’ 10.1” (3 m) 6’ 6.7” (2 m)
8’ 11.9” 5’ 8.5”
16’ 4.9” (5 m)
2
1
35
4
part No. Description Length Weight
241110200 ALUMINUM DOUbLE TRUSS LEDGER 2.0 m 6' 6.7" 17.6 lbs.
241110300 ALUMINUM DOUbLE TRUSS LEDGER 3.0 m 9' 10.1" 26.4 lbs.
part No. Description Length Weight
241111080 TRUSS CENTRAL FITTING (GA) 2’ 7.5” 17.8 lbs.
part No. Description Length Weight
219905320 TRUSS END FITTING MEKA 48 (GA) 1’ 0.6” 10.6 lbs.
1’ 7.7”
1’ 7.7”
1’ 7.7”
MODULAR SCAFFOLD
14 DACAME
The planks comply with the EN 12811 requirements. An extremely resistant perforated working area manufactured with anti-slip grooves. The 2 welded tubes make them easy to handle. Width: 1.18” (30 cm). hot galvanized and with a minimum thickness of 75 microns. Complying with the 12810-2 fall arrest system requirements.
FIXED STEEL pLANKS
ACCESS pLANKS
h: edge heightC: load capacity
The planks comply with the EN 12811 requirements. Aluminum structural frame. A working area made of 0.47” (12 mm) thick, damp-proof and anti-slip board. Ladder supplied separately.
h: edge heightC: load capacity
ACCESS LADDER
Manufactured with 6061 aluminum. Complying with EN 131-1 and 2 requirements. hooks on the upper end and anti-slip feet below. Step width 1’ 3.7” (40 cm).
11.8”
h
L
L
1’ 11.6”
h
part No. COMpONENT h C Length Weight
210500070 FIXED pLANK MEKA 48 · 0.7 m C-6 (GA) 2.8" 123 psf. 2' 3.6" 10.4 lbs.
210500100 FIXED pLANK MEKA 48 · 1.0 m C-6 (GA) 2.8” 123 psf. 3' 3.4" 13.4 lbs.
210500150 FIXED pLANK MEKA 48 · 1.5 m C-5 (GA) 2.8” 92 psf. 4' 11.1" 18.7 lbs.
210530200 FIXED pLANK MEKA 48 · 2.0 m C-4 (GA) 2.8” 62 psf. 6' 6.7" 24.2 lbs.
210530250 FIXED pLANK MEKA 48 · 2.5 m C-4 (GA) 2.8” 62 psf. 8' 2.4" 28.6 lbs.
210530300 FIXED pLANK MEKA 48 · 3.0 m C-4 (GA) 2.8” 62 psf. 9' 10.1" 35.2 lbs.
210500200 FIXED pLANK MEKA 48 · 2.0 m C-6 (GA) 3.1” 123 psf. 6' 6.7" 33.0 lbs.
210500250 FIXED pLANK MEKA 48 · 2.5 m C-6 (GA) 3.1” 123 psf. 8' 2.4" 40.7 lbs.
210500300 FIXED pLANK MEKA 48 · 3.0 m C-6 (GA) 3.1” 123 psf. 9' 10.1" 47.4 lbs.
part No. COMpONENT h C Length Weight
210600200 ACCESS pLANK MEKA 48 · 2.0 m (W/AL) 3.9” 62 psf. 6' 6.7" 39.6 lbs.
210600250 ACCESS pLANK MEKA 48 · 2.5 m (W/AL) 3.9” 62 psf. 8' 2.4" 48.5 lbs.
210600300 ACCESS pLANK MEKA 48 · 3.0 m (W/AL) 3.9” 62 psf. 9' 10.1" 57.3 lbs.
part No. Description Length Weight
240920000 ACCESS LADDER 206 cm (AL) 6' 9.1" 7.5 lbs.
MEKA 48
15DACAME
ACCESS LADDER SUppORT
Allows for the first access ladder to be properly inclined without the need of steel planks. Attached to the ledger using a Ø 1.9” (48.3 mm) clamp.
TOEbOARDS
Designed to complete the side protection (guardrail). Made from anti-humidity wood. Metal clamps on both ends. Offering 0.59” (15 cm) of protective height.
pLANK EXTENSION bARS
bRACKETS
To cover any gaps that appear as a result of the planks being erected where the structure comprises varying widths. Erected on the ends. Manufactured with hot galvanized steel. Load capacity 200 kg/m2. Width 0,31” (8 cm).
The brackets open up a variety of possibilities for the system by increasing the size of the work area.Secured using locks and bolts.
0.31”
L
L
part No. Description Width Weight
212390010 LADDER SUppORT (W 40 cm) (GA) 1’ 3.7” 9.9 lbs.
part No. Description Length Weight
210800700 TOEbOARD MEKA 48 · 0.7 m (WD) 2' 3.6" 4.6 lbs.
210801000 TOEbOARD MEKA 48 · 1.0 m (WD) 3' 3.4" 5.9 lbs.
210801300 TOEbOARD MEKA 48 · 1.3 m (WD) 4' 3.2" 6.8 lbs.
210801500 TOEbOARD MEKA 48 · 1.5 m (WD) 4' 11.1" 7.7 lbs.
210802000 TOEbOARD MEKA 48 · 2.0 m (WD) 6' 6.7" 9.9 lbs.
210802300 TOEbOARD MEKA 48 · 2.3 m (WD) 7' 6.6" 10.6 lbs.
210802500 TOEbOARD MEKA 48 · 2.5 m (WD) 8' 2.4" 12.6 lbs.
210803000 TOEbOARD MEKA 48 · 3.0 m (WD) 9' 10.1" 14.8 lbs.
part No. Description Length Weight
211220080 pLANK EXTENSION 200x8 cm (GA) 6' 6.7" 13.2 lbs.
211225080 pLANK EXTENSION 250x8 cm (GA) 8' 2.4" 16.3 lbs.
211230080 pLANK EXTENSION 300x8 cm (GA) 9' 10.1" 19.4 lbs.
part No. Description Length Weight
210700030 bRACKET MEKA 48 · 0.4 m (GA) 1' 3.7" 9.5 lbs.
210700070 bRACKET MEKA 48 · 0.7 m (GA) 2' 3.6" 14.5 lbs.
210700100 bRACKET MEKA 48 · 1.0 m (GA) 3' 3.4" 20.7 lbs.
MODULAR SCAFFOLD
16 DACAME
STAbILIZERS
With similar characteristics to brackets, stabilizers help to prevent mobile towers and other structures from toppling.
Secured using screws and bolts.
TELESCOpIC STAbILIZER
Used for scaffolds where tying the structure to a wall is not an option as well as for mobile towers. An articulated base plate allows it to adapt well to the surface. The adjustable telescopic arm can be operated with a snap pin. 2 clamps secure it to the standards.
1 2 3
4
1
2
3
4
TIE bARSAn indispensable component for securing the scaffold to the structure's facade. It should be used with an EN 74 Ø 1.89” pipe-clamp. hook diameter: 0.71” (18 mm).
pROVISIONAL GUARDRAIL (two struts and two telescopic bars)
provides security whilst the different levels of the scaffold are being erected. Zinc coated.Secured to the standard with a double wedge. The guardrails are telescopic and take up different positions along the breath of the structure.
Example of a provisional guardrail in use. In step 1 the fitter secures the perime-ter of the plank level with the provisional assembly rail.In step 2 the ledgers are installed and the provisional guardrails are taken down.
1 2
part No. Description Length Weight
211300030 STAbILIZER MEKA 48 · 0.4 m (GA) 1' 3.7" 9.5 lbs.
211300070 STAbILIZER MEKA 48 · 0.7 m (GA) 2' 3.6" 14.5 lbs.
211300100 STAbILIZER MEKA 48 · 1.0 m (GA) 3' 3.4" 20.7 lbs.
part No. Description Length Weight
025029089 TIE bAR 0.5 m (GA) 1' 7.7" 3.3 lbs.
025029099 TIE bAR 1.0 m (GA) 3' 3.4" 5.3 lbs.
025029109 TIE bAR 1.5 m (GA) 4’ 11.1” 7.5 lbs.
part No. Description Length Weight
251200500 TELESCOpIC STAbILIZER · 6 m (GA) 14’ 1” to 20’4.3 to 6.1 m 48.5 lbs.
part No. Description Length Weight
210900000210900010
pROVISIONAL ASSEMbLy GUARDRAIL MEKA 48 (ZN)
6’ 7” to 9’ 10” 2.0 to 3.0 m 35.2 lbs.
MEKA 48
17DACAME
pROTECTION FAN
Designed to catch objects that fall from the scaffolding with the metal planks assembled on top. Secured to the standard using two Ø 1.89” (48 mm) pipe-clamps.
ACCESS STEpS
OUTER GUARDRAIL - ACCESS STEpS -
INNER GUARDRAIL - ACCESS STEpS -
Ideal for creating access points in the scaffold structure. Anti-slip steps and landings. Width of steps 1’ 11.6” (60 cm). The models manufactured with 6061 aluminum are very lightweight, making assembly easier, while the hot galvanized steel model is ideal for access points that need a great-er loading capacity.
Manufactured with Ø 1.57” (40 mm) pipe, it is assembled onto the stan-dards rosettes with locks similar to those found on the ledgers.
Manufactured with Ø 1.26” (32 mm) pipe, it is assembled onto the access ladder struts using the two inverted U-shaped contours on both ends of the main pipe. For fastening the guardrail securely, the contours have connec-tion holes. It opens up the step's landing as a passageway.
1
2
1 2
1
2
1 2
L
L
L
L
h
h
h
h
60 cm
part No. Description L x h Weight
211420200 OUTER GUARDRAIL M 48 · 2x2 m (GA) 6’ 6.7” x 6’ 6.7” 12.1 lbs.
211420300 OUTER GUARDRAIL M 48 · 3x2 m (GA) 9’ 10.1” x 6’ 6.7” 15.0 lbs.
part No. Description L x h Weight
211520200 INNER GUARDRAIL M 48 · 2x2 m (GA) 6’ 6.7” x 6’ 6.7” 13.2 lbs.
211520300 INNER GUARDRAIL M 48 · 3x2 m (GA) 9’ 10.1” x 6’ 6.7” 16.5 lbs.
part No. Description L x h Weight
210900108 pROTECTION FAN 1.35 x 1.35 m (GA) 4’ 5” x 4’ 5” 22.0 lbs.
part No. COMpONENT C L x h Weight
240920200 ACCESS STEpS 2x2 m (W 60 cm) (AL) 41 psf. 6’ 6.7” x 6’ 6.7” 44.1 lbs.
240920300 ACCESS STEpS 3x2 m (W 60 cm) (AL) 41 psf. 9’ 10.1” x 6’ 6.7” 54.0 lbs.
212420300 ACCESS STEpS 3x2 m (W 60 cm) (GA) 62 psf. 9’ 10.1” x 6’ 6.7” 101.3 lbs.C: load capacity
MODULAR SCAFFOLD
18 DACAME
EXAMpLES OF ACCESS STEpS IN USE
• MODULAR SCAFFOLDING MEKA 48 WITh ZIGZAG ACCESS STEpS
• MODULAR SCAFFOLDING MEKA 48 WITh pARALLEL ACCESS STEpS
1.- SCREW JACK bASE 0.5 m 2.- bASE COLLAR MEKA 48 (GA) 3.- STANDARD MEKA 48 1.0 M (GA) 4.- STANDARD MEKA 48 2.0 m (GA) 5.- LEDGER MEKA 48 0.7 m (GA) 6.- LEDGER MEKA 48 1.3 m (GA) 7.- LEDGER MEKA 48 2.3 m (GA) 8.- LEDGER MEKA 48 3.0 m (GA) 9.- DIAGONAL bRACE MEKA 48 2x3 m (GA)10.- ACCESS STEpS 3x2x0.6 m (AL)/(GA)11.- OUTER GUARDRAIL 3x2 m MEKA 48 (GA)12.- INNER GUARDRAIL 3x2 m MEKA 48 (GA)13.- SpIGOT WITh CLAMp MEKA 48 (GA)14.- TIE bAR 0.5 m (GA)15.- FIXED CLAMp Ø48
1.- SCR. JACK bASE 0.5 m 2.- bASE COLLAR 3.- STANDARD 2 m 4.- STANDARD 3 m 5.- LEDGER 0.7 m
6.- LEDGER 2.0 m 7.- LEDGER 2.3 m 8.- LEDGER 3.0 m 9. FIXED pLANK 2 m C-4 10. FIXED pLANK 3 m C-4
11.- SIDE GUARDRAIL MEKA 48 0.7 m (GA)12.- ASSEMbLy GUARDRAIL MEKA 48 2 m (GA)13.- OUTER GUARDRAIL 3 x 2 m MEKA 48 (GA)14.- INNER GUARDRAIL 3 x 2 m MEKA 48 (GA)15.- ACCESS STEpS 3x2x0.6 m (AL)/(GA)16.- TOEbOARD MEKA 48 0.7 m (WD)17.- TOEbOARD MEKA 48 2.0 m (WD)18.- SpIGOT WITh CLAMp MEKA 48 (GA)19.- TIE bAR 0.5 m (GA)20.- FIXED CLAMp Ø48
2 m
1 m
2 m
2 m7 m
2 m
1 m
2 m
2 m7 m
1.3 m
3 m
0.7 m
0.7 m
3 m 2 m2 m
MEKA 48
19DACAME
ASSEMbLy pROCEDURE
1 2
3 4
6
7 8
5
Starting from the highest point, place the screw jack bases on the ground. It is recommended the ground to be compacted with sole boards in order to distribute the weight of the load. Insert a base collar into each of the screw jack bases.
Using the holes of the rosettes, connect the base collar to the ledgers. Level the screw jack bases beginning at the highest point.
Assembly the fixed and access planks using the access ladder support fitted to the ledger to hold up the access ladder. Reinforce the scaffold assembling the diagonal brace.
place the provisional guardrail to reach to the first level. Then assembly the ledgers and the toeboards.
Erect the following levels with standards 2 m and join them with ledgers, as shown in step 3.
place the planks on the next level and continue to rein-force the scaffold diagonally.Stiffen the scaffolding to the facade using tie bars, fixed clamps, tie supports and plugs as required in each scenario. place the provisional guard-rail to the next level in order to be able to access it safely.
Complete the side protection assembling the ledgers and the planks. Repeat steps 6, 7 and 8 for more levels.
Insert the standards into the base collars in order to erect the first level:• Standards 3.0 m where guardrails are used.• Standards 2.0 m everywhere else.
Join the standards with the ledgers.
DACAME, s.l.
Ctra. santa Bárbara - la sénia, km 4,6
43515 - la Galera
tarragona - spAIN
phone: + 34 977 71 70 04
Fax: + 34 977 71 93 89
www.dacame.com
Aluminum rolling tower Alu 50
rolling tower sYs-FAst
rolling tower MEKA 48
Multipurpose tower
shoring tower D
stages, ramps & grandstands.
Accessories
Modular scaffold MEKA 48
sectional scaffold sECus
ladder frame scaffold
European frame scaffold DINO 48
European frame scaffold FrEE 48
Facade scaffold DuO 45
Access towers
V.05-1510 NA
product manufacturer: DACAME S.L. product design: DACAME S.L. Graphic design: DACAME S.L. production: DACAME, S.L.The content of this catalogue is fully protected by copyright and the total or partial reproduction of images, texts, illustrations and graphics
without the express consent of DACAME S.L. is strictly prohibited.Legal Deposit T 1268-2015