MODEL FRONT WIDTH BACK WIDTH HEIGHT DEPTH ......outside of front wall framing. 2 x 4s must be used...
Transcript of MODEL FRONT WIDTH BACK WIDTH HEIGHT DEPTH ......outside of front wall framing. 2 x 4s must be used...
Specifications
Additional information can be found online at www.heatnglo.com or www.fireplaces.com
12-3/4"[324]
23-1/2"[597]
1/2"[13]
5-7/8"[149]
31-1/8"[791]
40-1/2"[1029]
16" [406]
56-1/2"[1435]
12"[305]
16-3/4"[425]
29-1/4" [743]
37" [940]
40" [1016] 1"[25]
1"[25]
42" [1067]
9-3/4"[248]
7-3/8"[187]
1" [25]
12-3/4"[324]
23-1/2"[597]
1/2"[13]
5-7/8"[149]
31-1/8"[791]
40-1/2"[1029]
16" [406]
56-1/2"[1435]
12"[305]
16-3/4"[425]
29-1/4" [743]
37" [940]
40" [1016] 1"[25]
1"[25]
42" [1067]
9-3/4"[248]
7-3/8"[187]
1" [25]
MODEL FRONT WIDTH BACK WIDTH HEIGHT DEPTH FIREBOX OPENING
NORTHSTAR-CActual Framing Actual Framing Actual Framing Actual Framing
37 x 31-1/840 42-1/2 40 42-1/2 40-1/2 56-3/4 23-1/2 24*
Please consult the manufacturer’s installation manual for all details and requirements before making a final
design layout decision.
Northstar-CWood-burning Fireplace
Northstar-C
Top View
Front View Right Side View
*If interior of chase will be drywalled, add the thickness to this measurement.
XXXXXXSpecifications
WS/HNG/NORTHSTAR-C_1119
PRODUCT LISTING CODES
US UL 127
CAN ULC-S610-M87
Additional information can be found online at www.heatnglo.com
Product information provided is not complete and is subject to change without notice. Product installation must adhere strictly to instructions accompanying product to avoid risk of fire and potential injury.
Lakeville, MN Phone: (888) 427-3973 Web: www.heatnglo.com
24*[610]
42-1/2" [1080]54-1/2"[1384]
16"[406]
42-1/2"[1080]54-1/2" [1384]
16"[406]
24"*[610]
24"*[610]
54-1/2"[1384]
16" [406]
48" [1219]
89-1/2"[2273]42-1/2"
[1080]
63-5/16" [1608]
44-3/4"[1137]
24-1/2"*[622]
24-1/2"*[622]
Across a corner
In an exterior chase
*If interior of chase will be drywalled, add the thickness to this measurement.
Along a wall
As a divider
Faceplate to sidewall 16 inches
42-1/2"[1080]
FasciaOuter Shell Flange
Protective metalhearth strip
Tile,marble or other non-combustible finish material
Minimum 2" [51] Cement Board or equivalent, (or one piece HX4)
Minimum 20" [508] in front and 8" [203] on sides to fuel opening
Combustible Floor
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . .
. . .
. . .
. .
Non-combustible material supplied with unit.
. . .
. . .
. . .
. .
Non-combustible sealant or groutTile,marble or other non-combustible finish material
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8" [203] minimum from each side offuel opening
41" [1041]20" [508]
(ceiling)
(roof)
(ceiling)
2" (51mm) min.
Attic Insulation
Shield
Ceiling Firestop(attic)
Storm Collar
Roof Flashing
2" min.(51mm)
2" (51mm) min.
2" (51mm) min.
Ceiling Firestop Offset/Return with hanger straps
2"(51mm)
min. 2"(51mm) min. Must have 2" (51mm)
minimum clearanceto header
Electrical wires must be a minimum of 16" (406mm) from top
1" (25mm) to side of appliance
1/2" (13mm) to backof appliance
0"to floor
36" (914mm) Top of appliance to
ceilingChimney Air Kit required with SL chimneyDuraPlus base plate required with Duraplus chimney
2 x 4 header
12" (305 mm)
3/4"(19 mm)maximum
Grid represents 1" squares
60" (1524mm)Measured up from
the base of the fireplace.
Non-combustible Decorative Facingsuch as: Steel, iron,brick, tile, concrete,slate, tile, plasters.DO NOT cover anyair openings in the face of the fireplace.
48" (1219 mm)Measured up from
the base of the fireplace.
Non-combustible board
Combustible mantel may be positioned anywhere within the grid area.
Seal joint withnon-combustiblesealant to prevent heat from being drawn into the wall cavity
Position combustible mantel 60" (1524 mm) from base of fireplace
12"(305 mm)
56-3/4"(1441 mm)
24" *(610 mm) 48-1/2"
(1232 mm)
42-1/2"(1080 mm)
The finished cavity depth must be no less than 24" (610 mm) from the finished backwall to the outside of front wall framing.
2 x 4s must be used for the header and framing above the header to maintain pipe clearances.
Double studs to catch non-combustible board and wall facing material.
*If interior of chase will be drywalled, add the thickness to this measurement.
Allow 12" minimum cavity depth if using an elbow/bend for the required outside air. Duct may be installed on either side.
14-1/2" (368 mm) for SL300 Chimney16" (406 mm) for DuraPlus Chimney
Non-combustible mantle may be positioned as low as 1 in. above the Fascia (Fronts) and 12 in. deep or from the base of the fireplace 38 in. up.
12"(305 mm)
FRAMING DIMENSIONSAPPLIANCE LOCATION
Specifications
MANTEL PROJECTIONS
HEARTH EXTENSION
HEARTH EXTENSION CONSTRUCTION
Northstar-C
CLEARANCE TO COMBUSTIBLES
You must use 2x4’s for the header in order to maintain clearances to the pipe.
See install manual figure 7.8 for raised hearth extention.