MODEL ER-A450Tmscashdrawer.com/docs/Sharp/SHARP ERA450TUPM.pdfELECTRONIC CASH REGISTER MODEL...

ELECTRONICCASH REGISTER

MODEL ER-A450T(For "U" & "A" version)SRV KEY : LKGIM7113BHZZPRINTER : PR-45M

SHARP CORPORATIONThis document has been published to be usedfor after sales service only.The contents are subject to change without notice.

CHAPTER 1. SERVICE (SRV) MODE . . . . . . . . . . . . . . . . . . . . . . . . . . 1

CHAPTER 2. PROGRAM (PGM2/PGM1) MODE. . . . . . . . . . . . . . . . . 17

CHAPTER 3. OP X/Z, X1/Z1, X2/Z2 MODE . . . . . . . . . . . . . . . . . . . . . 44

CONTENTS

CHAPTER 1. SERVICE (SRV) MODE

The SRV key is used for operating in the SRV mode.

1. SRV. reset (Program Loop Reset)

Used to return the machine back to its operational state after a lock-up has occurred.

Procedure• Method 1

1) Turn off the AC switch.

2) Set the mode switch to (SRV′) position.

3) Turn on the AC switch.

4) Turn to (SRV) position from (SRV′) position.

• Method 2

1) Set the mode switch to PGM2 position.


3) While holding down JOURNAL FEED key and RECEIPT FEEDkey, turn on the AC switch.

Note: When disassembling and reassembling always power up us-ing method 1 only. Method 2 will not reset the CKDC8.

Note: SRV programming job#926-B must be set to "4" to allow PGMprogram loop reset.

PRG. RESET

2. Master reset (All memory clear)

There are two possible methods to perform a master reset.

• MRS-1Used to clear all memory contents and return machine back to itsinitial settings. return keyboard back to default. for default key-board layout.

Procedure


2) Set the MODE switch to the (SRV′) position.


4) While holding down JOURNAL FEED key, turn to (SRV) positionfrom (SRV′) position.

• MRS-2Used to clear all memory and keyboard contents.This reset returns all programming back to defaults. The keyboardmust be entered by hand.This reset is used if an application needs different keyboard layoutother than that supplied by a normal MRS-1.

Procedure


2) Set the MODE switch to the (SRV′) position.


4) While holding down JOURNAL FEED key and RECEIPT FEEDkey, turn to (SRV) position from (SRV′) position.

5) Key position assignment:

After the execution of MRS-2, only the RECEIPT FEED andJOURNAL FEED keys can remain effective on key assignment.Any key can be assigned on any key position on the main key-board.

[key setup procedure]

MASTER PRESET

NOTES:

1: When the 0 key is pressed, the key of the key number ondisplay is disabled.

2: Push the key on the position to be assigned. With this, the keyof the key number on display is assigned to that key position.

Key number Key name Key number Key name

1 Numeric key "0" 10 Numeric key "9"



4 Numeric key "3" 13 Decimal point key

5 Numeric key "4" 14 CL key

6 Numeric key "5" 15 @/FOR key

7 Numeric key "6" 16 SBTL key

8 Numeric key "7" 17 CA/AT key

9 Numeric key "8"

3. Reading of the SRV mode program

List of program reports

JOB# Report name

900SRV-mode program full item report (not incl. keyboardlayout)

950Keyboard layout report (on keys other than dept. keysand direct PLU keys)

951Keyboard layout report (on dept. keys and direct PLUkeys)

970 SRV memory File allocation report

MRS-2 executed Key position set Free key

Disable

Free key setupcomplete.

*2

*1

0

0

[JOB# 900]All parameters contained for the SRV mode as listed

Key operation.

900 → @/FOR → CA/AT

Header graphical logo(Default:Graphical LOGOonly)

Date/TimeMachine No./Consective No.

JOB#

JOB#//Programmingdata(ABCD)

General Z1 reset counter

General Z2 reset counterDaily net Z2 reset counter

GT2 counter

GT3 counter

Secret code for PGM2 mode

Initial text mode programming

Hourly Z1 reset counterPLU Z1/Z2 reset counterCashier Z1/Z2 reset counterPBLU Z1 reset counter

Training GT counter

[JOB# 950]The Key layout report is printed in SRV mode

Key operation

950 → @/FOR → CA/AT



JOB#

Key No./Key label name/Location No.

Key No./Key label name/Location No.(---:Not used)

Key operation

951 → @/FOR → CA/AT



JOB#

Key No./Key label name/Location No.

Key No./Key label name/Location No.(---:Not used)

[JOB#970]Reading the contents of memory File Allocation

Key operation

970 → @/FOR → CA/AT

[JOB#990]Reading the Contents of the SRV-Mode Programming for SSP

Key operation

990 → @/FOR → CA/AT

Note: The SRV mode programming printout lists the actual memory files.For reference to memory file groups, please refer to SRV JOB#971 on page 14.


Date/Time

Machine No./Consective No.

JOB#

File table No./No.of records/No.of used records

File table No./No.of records/No.of blocks/No.of used records

File memory start addressEmpty memory start addressMemory end address



JOB#

SSP No.Step No./SSP data

Error message

4. Service mode programming

The following is the key sequence required for programming.

Details of [A][B][C][D] will be discussed at each item description.

mark is MRS setting.

[JOB #901]:MRS=0002 [For "U" version]#901-A, B: Not used (Fixed at "00")

#901-C: 1. Rounding system

1. Rounding system 901-C

Normal 0

SINGAPORE 8

#901-D: 1. TAB setting

1. TAB setting 901-D

0 0

0.0 1

0.00 2

0.000 3

[JOB #901]: MRS=0002 [For "A" version]#901-A: Not used (Fixed at "0")

#901-B: 1. Tax system

1. Tax system 901-B

Auto tax 1-4 & manual tax 0

CANADIAN TAX 6

#901-C: 1. Rounding system

1. Rounding system 901-C

Normal 0

SINGAPORE 8

#901-D: 1. TAB setting

1. TAB setting 901-D

0 0

0.0 1

0.00 2

0.000 3

[JOB#902] NOT USED MRS=0000

[JOB#903] MRS=4000#903-A: 1. ECR data copy baud rate

1. Baud rate (bps) 903-A

2400 2

4800 3

9600 4

19200 5

38400 6

The communication speed with the ER-02FD is 19200bps max.

#903-B, C: Not used (Fixed at "00")

#903-D: 1. Type of food stamp system

1. Type of food stamp system 903-DNo food stamp 0

Tax not payable in food stamps 1

Tax payable in food stamps 2

Food stamp tax forgiveness 3

[JOB#904] MRS=0000

#904-A: 1. Printing of date

1. Printing of date 904-AYes 0

No 4

#904-B: 1. Printing of consecutive No.

1. Printing of consecutive No. 904-BYes 0

No 4

#904-C, D: Not used (Fixed at "00")

[JOB#905] MRS=0005 [For "U" version]#905-A: 1. Taxable 4 subtotal print on X/Z report.

2. Gross Tax 4 and refund Tax 4 total print on X/Z report.

3. Net Tax 4 total print on X/Z report.

1. Taxable 4SBTL

2. Gross Tax 4and refundTax 4

3. Net Tax 4905-A

PrintPrint

Print 0

Skip 1

SkipPrint 2

Skip 3

SkipPrint

Print 4

Skip 5

SkipPrint 6

Skip 7

#905-B: 1. Tax printing when taxable subtotal is zero.

2. Tax printing when tax is zero.

1. Taxable subtotal iszero

2. Tax is zero905-B

SkipPrint 0

Skip 1

PrintPrint 4

Skip 5


XXX CA/AT

(Job#)

[A] [B] [C] [D]

Numeric entry4 digits max

0

@/FOR

[JOB#905] MRS=0005 [For "A" version]#905-A: 1. Taxable 4 subtotal print on X/Z report.

2. Gross Tax 4 and refund Tax 4 total print on X/Z report.

3. Net Tax 4 total print on X/Z report.

1. Taxable 4SBTL

2. Gross Tax 4and refundTax 4

3. Net Tax 4905-A

PrintPrint

Print 0

Skip 1

SkipPrint 2

Skip 3

SkipPrint

Print 4

Skip 5

SkipPrint 6

Skip 7

#905-B: 1. Tax printing when taxable subtotal is zero.2. Tax printing when GST is VAT.3. Tax printing when tax is zero.

1. Taxablesubtotal is zero

2. GST isVAT

2. Tax is zero905-B

SkipPrint

Print 0

Skip 1

SkipPrint 2

Skip 3

PrintPrint

Print 4

Skip 5

SkipPrint 6

Skip 7

#905-C: 1. GST EXPT print on X/Z report

1. GST EXPT 905-C

Print 0

Skip 4

#905-D: 1. TAX METHOD

Tax4method (GST)

Tax3 method Tax2, 1method (PST)

905-DGST PST

Type VAT VAT

Tax on Tax 0

Type Tax on Base 1

Type VAT

Tax on Tax 2

Type Tax on Base 3

Type Add on Tax

Tax on Tax 4

Type Tax on Base 5

Type Add on Tax VAT

Tax on Tax 6

Type Tax on Base 7

Type Add on Tax

Addon Tax

Tax on Tax 8

Type Tax on Base 9

[JOB#906] MRS=0021#906-A: 1. Print Dept. and PLU number on receipt.

1. Print Dept. and PLU number on receipt. 906-A

No 0

Yes 4

#906-B: 1. Bottle return function

2. Hash department setting

1. Bottle return function 2. Hash departmentsetting

906-B

DisableDisable 0

Enable 2

EnableDisable 4

Enable 6

#906-C: 1. Split pricing counting

2. Multiplication entry

1. Split pricing counting 2. Multiplication entry 906-C

Quantity

Multiplication 0

Successivemultiplication

1

Split pricing 2

Package

Multiplication 4

Successivemultiplication

5

Split pricing 6

#906-D: 1. UPC (EAN) price look up at refund entry

2. Presetting consecutive No.

3. Fractional quantity

1. UPC (EAN)price lookup at refundentry

2. PresettingconsecutiveNo.

3. Fractionalquantity

906-D

Yes

YesNo 0

Yes1

NoNo 2

Yes3

No

YesNo 4

Yes5

NoNo 6

Yes7

[JOB#907] MRS=0010#907-A : Not used (Fixed at "0")

#907-B: 1. UPC code printing on journal

2. UPC code printing on receipt

1. UPC code printing onjournal

2. UPC code printing onreceipt

907-B

YesYes 0

No 1

NoYes 2

No 3

#907-C: 1. Minus Dept./PLU/UPC

1. Minus Dept./PLU/UPC 907-C

Disable 0

Enable 1

#907-D: Not used (Fixed at "0")

[JOB#908] MRS=0740#908-A: GT print on Z report

GT1 (NET) GT2 (+) GT3 (–) 908-A

PrintPrint

Print 0

Skip 1

SkipPrint 2

Skip 3

SkipPrint

Print 4

Skip 5

SkipPrint 6

Skip 7

#908-B: GT print on X report

GT1 (NET) GT2 (+) GT3 (–) 908-B

SkipSkip

Skip 0

Print 1

PrintSkip 2

Print 3

PrintSkip

Skip 4

Print 5

PrintSkip 6

Print 7

#908-C: 1. Add void-mode transaction data to hourly total report

2. X1/Z1 report in X2/Z2 mode

3. Resetting of consecutive number in Z1 resetting

1. Addvoid-modetransactionto hourlytotal report

2. X1/Z1 reportin X2/Z2mode

3. Resetting ofconsecutiveNo. in Z1resetting

908-C

NoEnable

No 0

Yes 1

DisableNo 2

Yes 3

YesEnable

No 4

Yes 5

DisableNo 6

Yes 7

#908-D: 1. Printing X/Z report Journal only/Receipt & Journal (Ex-cept the individual cashier report)

2. Z1 resetting, resets GT Enable/Disable

1. Printing X/Z report 2. GT resetting at Z1 908-D

Receipt & JournalDisable 0

Enable 1

JournalDisable 4

Enable 5

[JOB#909] MRS=2000#909-A: 1. Printing of training GT on the X report

2. Printing of training GT on the Z report

1. Printing of trainingGT on the X report

2. Printing of trainingGT on the Z report

909-A

SkipPrint 0

Skip 1

PrintPrint 2

Skip 3

#909-B: 1. Printing of data on PLU resetting report

2. Printing of data on UPC resetting report

1. Printing of data on PLUresetting report

2. Printing of data onUPC resetting report

909-B

YesYes 0

No 1

NoYes 4

No 5

#909-C: 1. Printing of data in void-mode totalizer and manager voidtotalizer on Z2 report

2. Printing of data in void-mode totalizer and manager voidtotalizer on Z1 report

1. Void-mode totalizeron Z2 printing

2. Void-mode totalizeron Z1 printing

909-C

PrintPrint 0

Skip 2

SkipPrint 4

Skip 6


[JOB#910] MRS=0204#910-A: Not used (Fixed at "0")

#910-B: 1. Cashier code display.

2. Auto cashier sign off at the end of transaction

1. Cashier code display. 2. Auto cashier sign offat the end oftransaction

910-B

HiddenNo

(After cashier Z1 only)0

Yes (Everytime) 1

AppearNo

(After cashier Z1 only)2

Yes (Everytime) 3


[JOB#911] MRS=0000#911-A: 1. Fraction treatment

1. Fraction treatment 911-ARound off 0

Round up 1Round down 2

#911-B: 1. C/D check of UPC

2. C/D checking at the time of PBLU code entry

1. C/D check of UPC2. C/D checking at the

time of PBLU code entry911-B

NoNo 0

Yes 2

YesNo 4Yes 6


[JOB#912] MRS=0060#912-A: 1. Date print format

Date format 912-AMonth/Day/Year 0

Day/Month/Year 1Year/Month/Day 2

#912-B: 1. Time system

1. Time system 912-B12H 0

24H 1

#912-C: 1. After transaction receipt format

2. Copy receipt

3. Footer print control

1. Aftertransactionreceipt

2. Copyreceipt

3. Footer printcontrol 912-C

Total only

No

All receipt 0On selected functionkeys at the time offinalization

1

Yes


3

Detail

No


5

Yes


7

#912-D: 1. LOGO Message control.

1. LOGO Message control 912-D3-line header instead of a LOGO 0Graphical LOGO only 1

Graphical LOGO and 3-line footer 26-line header 3Graphical LOGO and 3-line header 43-line header and 3-line footer 5

[JOB#913] MRS = 0104#913-A: 1. Content of TOTAL VP amount

1. Content of TOTAL VP amount 913-ATotal amount 0

Tendered amount 1

#913-B: 1. Printing of SBTL

2. Printing of MDSE SBTL upon key depression

3. Escape the compulsion of VP or SLIP

NOTE: Must turn to MGR mode and depress

• , PRINT keys to escape validation

1. SBTL Print 2. MDSESBTL print

3. Escape thecompulsoryof VP

913-B

NoNo

Disable 0

Enable 1

YesDisable 2

Enable 3

YesNo

Disable 4

Enable 5

YesDisable 6

Enable 7

#913-C: 1. Buzzer off 2 sec. after lock error.

2. Buffered keyboard

1. Error beep 2. Buffered keyboard 913-C

2-sec. offYes 0

No 1

ConstantYes 2

No 3

#913-D: 1. Drawer closing operation

2. Error mode

3. Key catch sound

1. Drawer closedcompulsory

2. Error mode 3. Key catchsound

913-D

Non-compulsoryAll lock error

Enable 0

Disable 1

Miss operation(One shot error)

Enable 2

Disable 3

CompulsoryAll lock error

Enable 4

Disable 5

Miss operation(One shot error)

Enable 6

Disable 7

[JOB#914] MRS = 3100#914-A: 1. Receipt issuing at no-sale

2. [NS] key separation from [CA/AT] key for no sale func-tion is separate

3. Tax delete operation

1. Receipt issuingat no-sale

2. [NS] keyseparation

3. Tax delete914-A

EnableYes

Inhibit 0

Enable 1

NoInhibit 2

Enable 3

DisableYes

Inhibit 4

Enable 5

NoInhibit 6

Enable 7

Header

Footer

Type : 0

5

32

LOGO

1

4

LOGO

LOGO

#914-B: 1. No-sale after NON ADD code entry

1. No-sale after # entry 914-B

Disable 0

Enable 1

#914-C: 1. Action to be taken when the machine is locked by thereceipt/journal paper near end check

2. VOID mode

3. Non-add code entry at the beginning of a transactionoperation

1. Action to betaken whenthe machineis locked bythe journalpaper nearend check

2. VOID mode 3. Non-addcode entry atthe beginningof atransactionoperation

914-C

Unlocked by CLkey

EnableNon-compulsory 0

Compulsory 1

DisableNon-compulsory 2

Compulsory 3

Enforce ofpaper roll

replacement

EnableNon-compulsory 4

Compulsory 5

DisableNon-compulsory 6

Compulsory 7

#914-D: 1. Manual tax

2. CHECK CASHING

3. Non-add code entry

1. Manual tax 2. CHECKCASHING

3. Non-addcode entry

914-D

EnableDisable

Enable 0

Disable 1

EnableEnable 2

Disable 3

DisableDisable

Enable 4

Disable 5

EnableEnable 6

Disable 7

[JOB#915] MRS = 0000#915-A: 1. Amount symbol

1. Amount symbol 915-A" $ " 0

" " 1" " 2

#915-B: Not used (Fixed at "0")

#915-C: 1. Paper near end check

2. ST%, ST(–) as many times needed/operation only once

1. Paper near end check 2. ST%, ST(–) as manytimesneeded/operationonly once

915-C

YesUnlimited 0

Once only 2

NoUnlimited 4Once only 6


[JOB#916] MRS = 1400#916-A: 1. Print format when text and amount overlaps each other

REG mode

1. Print format when text and amountoverlaps each other REG mode

916-A

Truncate text 0

2 line print 1

#916-B: 1. Finalization by charge when SBTL 0

2. Food stamp subtotal entry before food stamp tender

1. Finalization bycharge whenSBTL 0

2. Food stamp subtotalentry before food stamptender

916-B

RF type of sale onlyNon-compulsory 0

Compulsory 1

AllowedNon-compulsory 4

Compulsory 5

#916-C: 1. Negative merchandise subtotal

2. Subtotal entry compulsory before tendering

3. Subtotal entry before direct non-tendering finalization

1. Negativemerchan-disesubtotal

2. Subtotal entrycompulsorybeforetendering

3 .Subtotal entrybefore directnon-tenderingfinalization

916-C

AllowNoncompulsory

Non-compulsory 0

Compulsory 1

CompulsoryNon-compulsory 2

Compulsory 3

DisallowNon-compulsory

Non-compulsory 4

Compulsory 5

CompulsoryNon-compulsory 6

Compulsory 7

#916-D: 1. Coupon PLU printing on X/Z report

2. Net sales subtotal (NET1) printing on X/Z report

3. CHECK change total printing on X/Z report

1. Print couponPLU’s onGeneral report

2. Print net salesSBTL (NET1)on Generalreport

3. Print CHKCHANGE onGeneral report

916-D

PrintPrint

Print 0

Skip 1

SkipPrint 2

Skip 3

SkipPrint

Print 4

Skip 5

SkipPrint 6

Skip 7

[JOB#917] MRS = 0000#917-A: 1. Printing of Taxable 1 subtotal on X/Z report

2. Printing of Gross Tax 1 and refund Tax 1 total on X/Zreport

3. Printing of Net Tax 1 total on X/Z report

1. Taxable 1subtotal onX/Z report

2. Gross Tax 1and refundTax 1 totalon X/Z report

3. Net Tax 1total on X/Zreport

917-A

PrintPrint

Print 0

Skip 1

SkipPrint 2

Skip 3

SkipPrint

Print 4

Skip 5

SkipPrint 6

Skip 7

#917-B: 1. Printing of Taxable 2 subtotal on X/Z report






917-B

PrintPrint

Print 0

Skip 1

SkipPrint 2

Skip 3

SkipPrint

Print 4

Skip 5

SkipPrint 6

Skip 7

#917-C: 1. Printing of Taxable 3 subtotal on X/Z report






917-C

PrintPrint

Print 0

Skip 1

SkipPrint 2

Skip 3

SkipPrint

Print 4

Skip 5

SkipPrint 6

Skip 7

#917-D: 1. Printing of Total Tax amount on X/Z report

2. Printing of Gross manual Tax and refund manual Taxon X/Z

3. Printing of Net manual Tax total on X/Z report

1. Total TaxAmount

2. Grossmanual Taxand Refundmanual Taxon X/Z report

3. Net manualTax total onX/Z report 917-D

PrintPrint

Print 0

Skip 1

SkipPrint 2

Skip 3

SkipPrint

Print 4

Skip 5

SkipPrint 6

Skip 7

[JOB#918] MRS = 2000#918-A: 1. Direct non-tendering finalization after previous tender

entry

1. Direct non-tendering finalization afterprevious tender entry

918-A

Disable 0

Enable 2

#918-B: 1. Fractional entries for non-scalable UPC/PLU/DEPT.

1. Fractional entries for non-scalableUPC/PLU/DEPT.

918-B

Enable 0

Disable 1


[JOB#919] MRS = 0400#919-A: Not used (Fixed at "0")

#919-B: 1. Checking of cashier# on guest check

2. PBLU code

1. Checking of cashier#on guest check

2. PBLU code919-B

YesAuto generation 0

Manual 1

NoAuto generation 4

Manual 5

#919-C: 1. PB entry

2. Amount printing when PLU unit price is 0.

1. PB entry 2. Amount printingwhen PLU unit price is0.

919-C

NoncompulsoryNo 0

Yes 1

CompulsoryNo 2

Yes 3

919-D: 1. Conversion SBTL printing of native SBTL

2. Foreign currency format

1. Conversion SBTLprint of native SBTL

2. Foreign currency919-D

YesNot 0

Omit digits lower thanTAB position

1

NoNot 4

Omit digits lower thanTAB position

5

[JOB#920] NOT USED MRS = 0000






[JOB#926] MRS = 0400#926-A: Not used (Fixed at "0")

#926-B: 1. Program reset in PGM 2 mode

1. Program reset at PGM2 mode 926-B

Disable 0

Enable 4

#926-C: 1. Open store/Close store with on-line

2. Send AT command string with JOB#500 (Open store)

3. Send AT command string with JOB#501 (Close store)

1. Openstore/Closestore foron-line

2. Send ATcommandstring withJOB#500(Open store)

3. Send ATcommandstring withJOB#501(Close store)

926-C

NoNo

No 0

Yes 1

YesNo 2

Yes 3

YesNo

No 4

Yes 5

YesNo 6

Yes 7

#926-D: 1. Connect on-line channel in close store

1. Allow connection of the on-linechannel in close store

926-D

No 0

Yes 4

[JOB#927] NOT USED: MRS = 0000

[JOB#928] MRS = 0000#928-A: 1. Printing of slip logo text

1.Printing of slip logo text 928-A

No 0

Yes 1

#928-B: 1. VP message printing on slip

2. Header line on slip paper when a reorder is madeprinted

1. VP message printingon slip

2. Header line on slippaper when a reorderis made printed

928-B

Check onlyPrinted 0

Not 1

Check & ChargePrinted 2

Not 3

#928-C:

1.Printing of PLU on bill when it is 0

1.Printing of PLU on bill when it is 0 928-C

Yes 0

no 4

#928-D 1. Printing of PB/SERVICE ON SLIP

2. Compulsory bill print system(The bill printing at serv and final in GLU system acts oneach media’s preset)

1. Printing ofPB/SERVICE ON SLIP

2. Compulsory bill printsystem

928-D

Yes

According to eachmedia’s preset

0

Compulsory for everyentry

1

Compulsory for PB 2

No

According to eachmedia’s preset

4

Compulsory for everyentry

5

Compulsory for PB 6

[JOB#929] MRS = 0000#929-A, B, C: Not used (Fixed at "000")

#929-D: 1. Taxable status of PLU/UPC which has not beens inPGM

1. Taxable status of PLU / UPC which isset at "Non-taxable" by PGM

929-D

According to its associated Department 0

Non-taxable 2

[JOB#930 ∼941] MRS = 0000RESET REPORT COUNTER

JOB # Function

930 Z1 report counter

933 Hourly Z1 report counter

934 PLU Z1/Z2 report counter

935 Cashier Z1/Z2 report counter

936 PBLU report counter

937 Z2 report counter

939 31 day daily net Z2 report counter

ABCD

"0000"

Job# @/FOR CA/AT

Initial value of Z counter

[JOB#942, 943, 969] MRS = 0000000000000GT COUNTER PRESETTING

JOB # Function942 GT2 (Positive GT)943 GT3 (Negative GT)969 TRAINING GT

Note: GT1 is obtained by calculationEquation: GT1=GT2-GT3

[JOB#944] MRS = 0000PGM2 secret code presetting

NOTE: When the secret code "0" is programmed, the secret codeentry is be inhibited.

[JOB#950] MRS = STANDARD KEY LAYOUTFree key layout (Except for department keys and direct PLU keys.)

XXX : 1 to 88: 999 (For inhibiting key)

[JOB#951] MRS = STANDARD KEY LAYOUTFree key layout (department keys and direct PLU keys)

XXX : 1 to 68: 999 (For Inhibiting key)

• Programming of the keys to be dept keys or direct PLU keys onthe keyboard.

• Key No. is assigned to each key which is supposed to be dept.Key or direct PLU key by depressing the key after entering the keyNo.

• Those keys programmed by this job No. will be dept. keys if dept.code is assigned, and will be direct PLU keys if PLU code isassigned in the PGM2 mode.

FUNCTION KEY LIST

Key No. KEY KEY TEXT 1 0 KEY 0 KEY 2 1 KEY 1 KEY 3 2 KEY 2 KEY 4 3 KEY 3 KEY 5 4 KEY 4 KEY 6 5 KEY 5 KEY 7 6 KEY 6 KEY 8 7 KEY 7 KEY 9 8 KEY 8 KEY10 9 KEY 9 KEY11 00 KEY 00 KEY12 000 KEY 000KEY13 DECIMAL POINT . KEY14 CLEAR CL15 @/FOR @/FOR16 SUB TOTAL SBTL17 CA/AT CA/AT18 MDSE SBTL MDS ST19 # #20 NO SALE NS21 PLU/SUB PLU/SB22 REFUND SALES RF SAL23 TAX1 SHIFT TAX1SF24 TAX2 SHIFT TAX2SF25 TAX3 SHIFT TAX3SF26 TAX4 SHIFT TAX4SF27 FS SHIFT FS SHT28 PRINT PRINT29 RCPT RCPT30 VOID VOID31 REFUND RFND32 %1 %133 %2 %234 %3 %335 %4 %436 (–)1 (–)137 (–)2 (–)238 (–)3 (–)339 (–)4 (–)440 TAX TAX41 AUTO AUTO42 AUTO2 AUTO243 AUTO3 AUTO344 AUTO4 AUTO445 AUTO5 AUTO546 AUTO6 AUTO647 AUTO7 AUTO748 AUTO8 AUTO849 AUTO9 AUTO950 AUTO10 AUTO1051 CASH2 CA252 CHECK CHK53 CHECK2 CHK254 CH1 CH155 CH2 CH256 CH3 CH357 CH4 CH458 CH5 CH559 CONV1 CONV160 CONV2 CONV2

0

000000000000013 digits

Job# CA/AT@/FOR

CA/AT944 XXXX4 digits

@/FOR

0

Free key@/FOR CA/AT

@/FOR

Key number automaticincrement

Key number manualincrement

Initial setting

XXXKey No.

To inhibitSBTL

increment key No.

950

Free key@/FOR CA/AT

@/FORKey No.

Key number automaticincrement

Key number manual increment

To inhibitSBTL

increment key No.

951 XXX

Key No. KEY KEY TEXT61 CONV3 CONV362 CONV4 CONV463 FS TEND FSTEND64 RA RA65 RA2 RA266 PO PO67 PO2 PO268 CASHIER NO. CASH#69 BIRTHDAY BIRTH70 UPC UPC71 AMT AMT72 DEPT# DEPT#73 REPEAT REPEAT74 INQUIRE INQ75 NO DELETE NO DEL76 PRICE CHANGE PRCHNG77 PRICE 1 P178 PRICE 2 P279 PRICE 3 P380 SLIP SLIP81 PBLU PBAL82 N.C. N.C.83 SERVICE SRVC84 FINAL FINAL85 DEPOSIT DEPO86 DEPOSIT RFND DEP.RF87 SCALE SCALE88 OPEN TARE OPN TR

999 INHIBIT

ER-A450T KEY POSITION

[JOB#971]Memory file group PROGRAMMING. (File creation deletion andchange of record count or block count)

Key operation

• Normal file

GroupNo.

File name Type* File table No.(Create/Erase)

1 Dept. 1 1,2,3,52 Dept. Text(12) 0 33 Dept. Text(16) 0 44 PLU 1 7,8,9,115 PLU Text(12) 0 96 PLU Text(16) 0 107 Link PLU 1 138 UPC 1 14,15,16,189 UPC Price1 0 16,2010 UPC Price1-3 0 17,2211 UPC Text(12) 0 1812 UPC Text(16) 0 1913 UPC Daily sales 0 20 (or 22)14 UPC Mix&Match 1 26,2715 UPC Link 1 2816 Cashier 1 32,33,34,35,3617 Hourly 0 40,4118 Daily Net 0 42,4319 Reg. Buffer 1 4420 PBLU 1 4521 Term Department 0 622 Term PLU 0 1223 Term UPC 0 21 (or 23)24 Term Transaction 0 3125 Term Cashier transaction 0 37

26All of Term files.

06,12,21 (or23),31,37

27 UPC PGM Pick up 1 2428 UPC X/Z Pick up 1 25

Type = 0 ; Create/Erase only

Type = 1 ; Create/Erase and Increase/decrease the number ofRecords or blocks.

* : The files which are created or erased by the entry of group No.

04 08 12 16 20 24 28 32 36 42 48 54 60 66

03 07 11 15 19 23 27 31 35 41 47 53 59 65

02 06 10 14 18 22 26 30 34 40 46 52 58 64

01 05 09 13 17 21 25 29 34 39 45 51 57 63

43 49 55 61 67

44 50 56 62 68

37

38

R J

:FIXED KEY (NO TO CHANGE)

971 XXXXXabc CA/AT@/FOR@/FOR

File group No. Number of records

File table

TableNo.

File nameRECORD BLOCK Label

sizeDatasizeMRS Max. #1 MRS Max. #2

1 Dept. Preset 20 50 1 1 1 7

2 Price 20 50 (1) 1 1 0 3

3 Text (12 chara.) 20 50 (1) 1 1 0 12

4 Text (16 chara.) 0 50 (1) 0 1 0 16

5 Daily 20 50 (1) 1 1 0 9

6 Term 20 50 (1) 1 1 0 9

7 PLU Preset 500 *** 1 1 5 7

8 Price 500 *** (7) 1 1 0 3

9 Text (12 chara.) 500 *** (7) 1 1 0 12

10 Text (16 chara.) 0 *** (7) 0 1 0 16

11 Daily 500 *** (7) 1 1 0 9

12 Term 0 *** (7) 0 1 0 9

13 Link PLU 0 *** 0 1 3 15

14 UPC Preset 1500 *** 1 1 9 6

15 Flag 1500 *** (14) 1 1 0 2

16 Price 1 1500 *** (14) 1 1 0 3

17 Price 1-3 0 *** (14) 0 1 0 9

18 Text (12 chara.) 1500 *** (14) 1 1 0 12

19 Text (16 chara.) 0 *** (14) 0 1 0 16

20 Daily (Price 1) 1500 *** (14) 1 1 0 9

21 Term (Price 1) 0 *** (14) 0 1 0 9

22 Daily (Price 1-3) 0 *** (14) 0 1 0 9

23 Term (Price 1-3) 0 *** (14) 0 3 0 9

24 UPC PGM Pick up 100 *** 1 3 9 0

25 UPC X/Z Pick up 100 *** 1 1 9 0

26 Mix & Match Table 0 *** 0 1 1 5

27 Sales buffer 0 *** (26) 0 1 0 5

28 UPC link 0 *** 0 1 7 15

29 Transaction Label 89 89 1 1 2 0

30 Daily 89 89 (29) 1 1 0 8

31 Term 89 89 (29) 1 1 0 8

32 Cashier Preset 4 99 4 99 (32) 1 3

33 Flag 4 99 (32) 4 99 (32) 0 2

34 Text 4 99 (32) 4 99 (32) 0 8

35 Cashier transaction Label 43 43 1 1 2 0

36 Daily 43 43 (35) 1 1 0 8

37 Term 43 43 (35) 1 1 0 8

38 Total cashier buffer Label 43 43 1 1 2 0

39 Total 43 43 (38) 1 1 0 8

40 Hourly Label 48 48 1 1 1 0

41 Daily 48 48 (40) 1 1 0 8

42 Daily net Label 36 36 1 1 3 0

43 Total 36 36 (42) 1 1 0 8

44 Reg. buffer 80 255 1 1 0 50

45 PBLU (Label + Data) 10 *** 1 1 2 125

(#1) : Same as the number of record of table No. N

(#2) : Same as the number of block of table No. N

[JOB#996, 998] RAM DATA BACKUP function(ECR ECR, ECR ER-02FD)

[JOB#996] RAM data send

X : SSP = 0

Standard RAM (128KB) = 1Optional RAM: ER-03RA (512KB) = 2

Only nacessarywhen the ER-01FDor ER-02FD is beingused.

[JOB#998] RAM data receive

[JOB#987] MRS = 0MRS = 0

Text Changing (To Default text)

X: 0 = English text

2 = French text

When this job is executed, below texts are set as default data.

(a) Function text

(b) Cashier text

(c) Each message text (LOGO, etc..)

5. PC software utility

(1) OutlineThis Specification document describes the "02FD.EXE" PC utility.

The "02FD.EXE" works with the Windows95/98 operating systemsand has the following functions by connecting ER-A450T via RS232.

02FD.EXE : All RAM Data Upload/Download

(2) Environment

PC and ER-A450T are connected by RS232.

Connect the PORT2(CH1) of the ER-A450T to the RS-232 interfaceof the PC.

RS232 Cable pin out :

996 X@/FOR

All data

CA/AT

SBTL

Send to ECR or ER-02FD(Baud rate setting:#903-A)Send to ECR(Auto baud rate setting)

998 @/FOR CA/AT

SBTL

Receive from ECR or ER-02FD(Baud rate setting:#903-A)Receive from ECR(Auto baud rate setting)

987 X

0

@/FOR CA/AT

PC

RS232 cable

ER-A450T

Channel No.Port1(CH8)

Channel No.Port2(CH1)

SD 3

RD 2

RTS 7

DCD 1

DTR 4

DSR 6

CTS 8

SG 5

3

2

7

1

4

6

8

5

SD

RD

RTS

DCD

DTR

DSR

CTS

SG

[ER-A450T] [PC]

No Procedure on P.C. side No Procedure on ER-A450T side

1Install "02FD.EXE" on the P.C.ALL RAM Data UpLoad : Go to "2"ALL RAM Data DownLoad : Go to "9"

2 ALL RAM Data UpLoad ( ER-A450T -> PC ) 2 Place the SRV key in the SRV mode.

3

"Execute "02FD.EXE" on P.C"*Don’ t execute the other Software at the same time.

4

Set the Communication method by "Setting" Button."

Push "OK" Button.

5Push "POS -> PC" Button.And Select the Receiving File.

6

Entry of JOB#996 in the SRV mode

ER-A450T shows

7

Communication starts.

8UpLoad is completed.The initial Window is shown."Push "Exit" Button."

8UpLoad is completed.

9 ALL RAM Data Download ( PC -> ER-A450T ) 9 Place the SRV key in the SRV mode.

996 CA/AT@/FOR

00000

No Procedure on P.C. side No Procedure on ER-A450T side

10

Execute "02FD.EXE" on P.C*Don’ t execute the other Software at the same time.

11

Set the Communication method by "Setting" Button.

12

Entry of JOB#998 in the SRV mode

ER-A450T shows

Push "OK" Button.

13Push "PC -> POS" Button.And Select the Receiving File.

14

Communication starts.

15Download is completed.The initial Window is shown.Push "Exit" Button.

15Download is completed.

16 Execute "Service Reseth" on ER-A450T

998 CA/AT@/FOR

00000

CHAPTER 2. PROGRAM (PGM2/PGM1) MODE

1.Reading of the PGM mode program

[JOB#1000]: UPC reading

[JOB#2020]: UPC Mix & Match readingKey operation

[JOB#2025]: UPC/EAN format programming reading

[JOB#2030]: UPC LINK preset or reading

XXXXXXXXXXXXX

Pick up (to the number of records in Pick-up file)

UPC code

(Scanning) ;Previous pick-upped UPC codes

;All UPC data

1000 @/FOR CA/AT@/FOR

CA/AT@/FOR

CA/AT

JOB#/Mode title



Taxable/Price

Programming JOB#2010-A,B,C/Age limitation/Mix & Match table Mo.

Non-delete flag/Taxable/Sign/Price

UPC code/Type *1/ Associated DEPT./ Base q'ty*1 L : Link UPC type/ (space) : Normal UPC

2020 @/FOR CA/AT



JOB#/Mode title

Table No./Matching count/Adjust amount

2025 @/FOR CA/AT

Programming:JOB#2025




JOB#/Mode title

2030 @/FOR CA/AT



JOB#/Mode title

Linked PLU code

[JOB#1100]: DEPT readingKey operation

[JOB#1200]: PLU readingKey operation

1100 XXStart No.

@/FOR CA/ATXXEnd No.

Single item

@/FOR

All



JOB#/Mode title

Range

DEPT. code/Taxable/PriceText/Group No.Programming:JOB#2110/Age limitation/HALO

1200 XXXXStart No.

@/FOR CA/ATEnd No.

Single item

@/FOR XXXX

All



JOB#/Mode title

Range

Taxable/Price

PLU code/Associated Dept.code/Type:L=Link PLU,(space)=Normal PLU/Base Q'ty

TextProgramming:JOB#2210/Age limitation

[JOB#2220]: LINK PLU PRESET READINGKey operation

[JOB#2119]: DIRECT KEY READINGKey operation

2220 @/FOR CA/AT



JOB#/Mode title

Range

PLU code/Linked PLU code(Max.5)

2119 @/FOR CA/AT



JOB#/Mode title

Key No./Dept.code(JOB#2119)

Key No./Inhibit

[JOB#1300]: FUNCTION PRESET READINGKey operation

1300 @/FOR CA/AT

JOB#/Mode title



Function No./Text

Type:S=Subtotal, I=Item/Sign/Amount

Function No./Text

HALO

Function No./Text/HALO

Function No./Text/HALO

[JOB#1500]: CASHIER READINGKey operation

[JOB#2600]: READING OF OTHERKey operation

1500 @/FOR CA/AT

JOB#/Mode title



Cashier No./Cashier codeName/Drawer No.

2600 @/FOR CA/AT

JOB#/Mode title






Programming:JOB#2630Programming:JOB#2631Programming:JOB#2632






[JOB#2640]: SLIP text program readingKey operation

[JOB#2700]: TAX TABLE READING REP.Key operation

[JOB#2800]: PBLU code program readingKey operation

[JOB#2900]: AUTO KEY READINGKey operation

2640 @/FOR CA/AT

JOB#/Mode title




2700 @/FOR CA/AT

JOB#/Mode title



Tax No./RateLower tax limitation

2800 @/FOR CA/AT

JOB#/Mode title



PBLU Code range

2900 @/FOR CA/AT

JOB#/Mode title



Auto key No.


Not programmed

[JOB#2990]: THERMAL PRINTER SETUP REPORT 2. Programming

[JOB#1000]PROGRAMMING UPC/EAN CODES DEPARTMENTS TO BE ASSO-CIATED WITH EANs

XXXXXXXXXXXXX: UPC code

YY: DEPT. code = 01 to 50

MRS = Nothing (Default = 01)

Default is a value which is set when new UPC record is created byanother programming JOB.

If the record of the entered UPC code is not in the UPC file at thisprogramming step, the UPC code will be created.

[JOB#1010]UPC UNIT PRICE PROGRAMMING


YYYYYY: Amount = 0 to 999999

MRS = 000000


To use the Price 2,3, it needs the PRICE1-3 file that is created bySRV file JOB.

[JOB#1011]UPC BASE Q’TY PROGRAMMING


ZZ : Base quantity = 00 to 99

MRS = 00


2990 @/FOR CA/AT

JOB#/Mode title



Printing sample

1000 YYXXXXXXXXXXXXX

No change

UPC code

(Scanning)

CA/ATSBTL

@/FOR @/FOR

YYYYYY1010 XXXXXXXXXXXXX

No change

UPC code

(Scanning)

CA/ATSBTL

@/FOR @/FOR

*Price 1~3

1011 ZZXXXXXXXXXXXXX

No change

UPC code

(Scanning)

CA/ATSBTL

@/FOR @/FOR

[JOB#2010]UPC FUNCTION PROGRAMMING


A: Price shift entry A

Allowed 0

Inhibited 1

Compulsory 2

B: Tare table No. B

Non 0

Table No. 1 to 9

C: Scale entry C

Inhibit 0

Enable 1

Compulsory 2

D: Record delete method D

Delete at X/Z non-accessedUPC deleting job

0

Non delete 1

Delete now 4


The default is a value is set when a new UPC record is created byanother programming JOB.


[JOB#2011]UPC TAX STATUS PROGRAMMING


A: Sign A

+ 0

- 1

B: Food stamp B

No 0

Yes 1

C: Taxable 4 C

No 0

Yes 1

D: Taxable 3 D

No 0

Yes 1

E: Taxable 2 E

No 0

Yes 1

F: Taxable 1 F

No 0

Yes 1

MRS = 0000000


[JOB#2014]UPC TEXT PROGRAMMING


Characters can be entered by using the character keys (directkey) or the numeric keys (code entry).Please refer to section 4.

MRS = 0000000


Note: The ER-A450T does not have "Readout of the programmedtext" because the text modification function is not supported.

[JOB#2017]UPC MIX & MATCH TABLE No. PROGRAMMING

XXXXXXXXXXXXX : UPC code

ZZ : Mix&Match table No. = 00 to 99

MRS = 00


2010 ABCDXXXXXXXXXXXXX

No change

UPC code

(Scanning)

CA/ATSBTL

@/FOR @/FOR

2011 ABCDEFXXXXXXXXXXXXX

No change

UPC code

(Scanning)

CA/ATSBTL

@/FOR @/FOR

Characterkey

All space

2014 XXXXXXXXXXXXXUPC code

(Scanning)

CA/ATSBTL

@/FOR @/FOR

2017 ZZXXXXXXXXXXXXX

No change

UPC code

(Scanning)

CA/ATSBTL

@/FOR @/FOR

[JOB#2020]MIX & MATCH TABLE PROGRAMMING

XX: Table No. = 01 to 99

ZZ: Matching count = 1 to 99

YYYYYY: Adjust amount = 1 to 999999

MRS = nothing

[JOB#2025]UPC/EAN CODE FORMAT PROGRAMMING

VV: System sign

A: Length of field 1

B: Length of field 2

C: Not used (Fixed at "0")

D: Meaning of field 2 D

Price 0

Quantity 2

E: Price check digit used E

No 0

Yes 1

F: TAB or Decimal point of field 2 F

0 0

0.0 1

0.00 2

0.000 3

MRS = (Below values are established)

Type VV A B C D E F

UPC8 2 2 4 0 0 0 2

UPC13 02 5 4 0 0 1 2

MRS format

<UPC LEAN CODE FORMAT>(Example)

UPC 13: VV WWWWW X YYYY Z

UPC 8: V WW YYYY Z

VVorV

WWWWW orWW

X YYYY Z

Systemsign

Field1Pricecheckdigit

Field2 Checkdigit

(Note)

ISBN/ISSN and press code always use the fixed format even if belownumbers are set as NON PLU code.

System sign = 37, 43, 78, 98, 97, 141

[JOB#2029]RECORD DELETE PERIOD PROGRAMMING

XX: Record delete period = 00 to 99 days(00= Record delete function is not available)

MRS = 99

[JOB#2030]UPC LINK (with PLU) PROGRAMMING


YYYYYY: PLU code = 1 to 999999 max.

MRS = 0

When the "SBTL" key is pressed without entering any number asthe first PLU code (YYYYYY), the previous data is cleared.

The PLU code should already be defined when they are used inthis programming step.

[JOB#2080]UPC LOWER LIMITATION AGE PROGRAMMING

XXXXXXXXXXXXX : UPC code

YY : Age = 00 to 99 (00 = No limitation)

MRS = 00


2020 ZZYYYYYYXX

Delete

Table No.

CA/ATSBTL

@/FOR @/FOR

System sign

ABCDEF

Max. =11

2025 VV

Delete

CA/ATSBTL

@/FOR @/FOR

2

System signField 2

PLU or DEPT. code:2 digits

PRICE:5 digits (00.00)

Check digit

0 2

System sign Field 1

PLU code:5 digits

Field 2

PRICE:4 digits (000.00)

Price Check digit

Check digit

<UPC8>

<UPC13>

Field 1

2029 XX

0

CA/AT@/FOR

Max. 5 times

YYYYYY2030 XXXXXXXXXXXXX

No change

UPC code

(Scanning)

CA/ATSBTL

@/FOR @/FOR

2080 YYXXXXXXXXXXXXX

No change

UPC code

(Scanning)

CA/ATSBTL

@/FOR @/FOR

[JOB#1110]PROGRAMMING DEPT. PRICE

XX: DEPT-CODE = 01 - 50

YYYYYY: PRICE = 0 - 999999

Preset price is max. 6 digits.

If a price is set for a department where the amount entry type is"INHIBIT" or "OPEN", its amount entry type is set as below automat-ically.

"INHIBIT" "PRESET" "OPEN" "OPEN&PRESET"

MRS = 000000

[JOB#2110]PROGRAMMING DEPT. FUNCTIONS

XX: DEPT. code = 01 ∼ 50XXA: Not used (Fixed at "0")

XXB: Item validation printing B

Non compulsory 0

Compulsory 1

C: Tare table No. C

Non 0

Table No. 1 to 9

D: Scale entry D

Inhibit 0

Enable 1

Compulsory 2

XXE: SICS Function E

Normal 0

Single item cash sale 1

Single item finalize 2

XXF: Dept. type F

Normal 0

HASH 1

Bottle Return 2

XXG: Amount entry type G

Inhibited 0

Open 1

Preset 2

Open and preset 3

MRS (Dept, 01~20) = 0000001

[JOB#2111]DEPT. TAX STATUS AND SIGN PROGRAMMING

XX: DEPT. CODE = 01 - 50

A: Sign A

+ 0

– 1

B: Food stamp B

Non-food stampable 0

Food stampable 1

C: Taxable 4 C

Non taxable 0

Taxable 1

D: Taxable 3 D

Non taxable 0

Taxable 1

E: Taxable 2 E

Non taxable 0

Taxable 1

F: Taxable 1 F

Non taxable 0

Taxable 1

MRS = 000000

[JOB#2112]DEPT. HALO (limit) PROGRAMMING

XX: DEPT. CODE = 01 - 50A: Mantissa (HALO) = 1 - 9B: Exponent (HALO) = 0 - 7

Items A and B indicate A × 10B. Any amount below that value isenable within 9999999.

MRS = 17

SBTL@/FOR @/FOR

No change

For the next code

(Show Current code & Code entry)

1110 YYYYYY

CL

priceCA/ATXX

SBTL@/FOR @/FOR

For next code

No change


2110 ABCDEFG

CL

CA/ATXX

SBTL@/FOR @/FOR

DEPT. CODE

For the next DEPT.

No change


2111

CL

CA/ATABCDEFXX

SBTL@/FOR @/FOR CA/ATXX

DEPT. CODE

For the next DEPT.

No change


2112 AB

CL

[JOB#2114]DEPT. TEXT PROGRAMMING

XXX: DEPT. CODE = 01 - 50

Characters can be entered by using the alphabetic keys (charact key)or the numeric keys (code entry).

Please refer to section 4 for further details.

MRS = DPT. XX

[JOB#2116]PROGRAMMING OF DEPT. GROUP

XX: DEPT. code = 01 - 50AA: Group No. = 0 - 9

MRS = 0

[JOB#2119]LINK NUMBER PROGRAMMING FOR DIRECT DEPT. KEYS

DEPT. code is assigned to the key no. Which has been programmedin JOB#951 programming.

XXX: Key No. = 001 - 068 AB: DEPT, CODE = 01 - 50

[JOB#2180]DEPARTMENT LOWER LIMITATION AGE PROGRAMMING

XX: Department code = 01 - 50 YY: Age: (00 ∼ 99), 00 = No Limitation

MRS = 0

[JOB#1200]Creating/assigning PLUs and the associated departments.

XXXXXX: PLU code = 01 - 999999AB: DEPT. code = 01 - 50

If the record of entered PLU code is not in PLU file at this program-ming, it will be created in PLU file.

MRS = (PLU 000001~000020) = 01

[JOB#1210]PLU PRICE PROGRAMMING

XXXXXX: PLU CODE = 1 - 999999

YYYYYY: Amount = 0 - 999999

If the record of the entered PLU code is not in the PLU file at thisprogramming step, the PLU code will be created.

If an amount is set for a PLU where the amount entry type is "IN-HIBIT" or "OPEN", its amount entry type is set as below automat-ically.

"INHIBIT" "PRESET" "OPEN" "OPEN&PRESET"

MRS = 000000

[JOB#1211]PLU BASE Q’TY PROGRAMMING

XXXXXX: PLU code = 1 - 999999ZZ: Base quantity = 00 - 99


2114

CL

All space

Character keyXX

DEPT. CODE

For the next DEPT.


@/FOR @/FOR SBTL CA/AT


DEPT. CODE

Next code

No change


2116 A

CL

SBTL@/FOR @/FOR CA/ATXXX

KEY No.

Next DEPT.

ABDEPT. code

inhibit

2119


No change

For the next code


YY2180

CL

SBTL@/FOR @/FOR CA/AT

PLU code

No change


ABXXXXXX

CL

1200


PLU CODE

For next code

No change


YYYYYYXXXXXX

CL

1210

SBTLZZ@/FOR @/FOR CA/ATXXXXXX

PLU CODE

For the next PLU

No change

(Show Current code & Code entry)CL

1211

[JOB#2210]PLU function programming

XXXXXX: PLU code = 1-999999

A: Tare table No. ANon 0Table No. 1 to 9

B: Scale entry BInhibit 0Enable 1Compulsory 2

C: Amount entry type CInhibited 0Open 1Preset 2Open and preset 3Delete 4


MRS = 002

[JOB#2211]PLU TAX STATUS PROGRAMMING

XXXXXX: PLU code = 1- 999999

A: Sign A+ 0– 1

B: Food stamp BNon stampable 0Stampable 1

C: Taxable 4 CNon taxable 0Taxable 1

D: Taxable 3 DNon taxable 0Taxable 1

E: Taxable 2 ENon taxable 0Taxable 1

F: Taxable 1 FNon taxable 0Taxable 1


MRS = 000000

[JOB#2214]PLU TEXT PROGRAMMING

XXXXXX: PLU CODE = 1 - 999999

Characters can be entered by using alphabet keys (direct key) or thenumeric keys (code entry).

Please refer to section 4.

MRS = PLXXXXXX

[JOB#2219]PLU CODE DEFINITION FOR DIRECT PLU KEYS

XXX: Key No. = 001 - 068YYYYYY: PLU code = 1 - 999999

The PLU code is assigned to the key No. which has been preset inSRV JOB#951 programming.

[JOB#2220]LINKED PLU PROGRAMMING

XXXXXX: PLU code = 1 - 999999YYYYYY: PLU code = 1 - 999999

When the "SBTL" key is depressed without entering any number in(YYYYYY), there is no link.

The PLU code should already be defined when they are used in thisprogramming step.

MRS = 0

[JOB#2280]PLU LOWER LIMITATION AGE PROGRAMMING

XXXXXX: PLU code = 01 - 999999YY: Age = 00 - 99, 00 = No Limitation

MRS = 0



No change

PLU code

For next code


ABCXXXXXX

CL

2210

SBTLABCDEF@/FOR @/FOR CA/ATXXXXXX

No change

For the next PLU

PLU code

CL

(Show current code & code entry)

2211

SBTLCharacter key@/FOR @/FOR CA/ATXXXXXX

For the next PLU

PLU code

All space

CL(Show Current code & Code entry)

2214


Next code

Key No.

inhibit

PLU code2219 YYYYYYXXX

SBTL2220 YYYYYY@/FOR @/FOR CA/ATXXXXXX

Max. 5 times

0

PLU CODE


No change

For the next code


XXXXXX YY2280

CL

[JOB#2230]PLU CODE PROGRAMMING (range)

XXXXXX: Start PLU code = 1 - 999999YYYYYY: End PLU code = 1 - 999999

AB: Dept. code = 1-50

[JOB#2231]PLU function programming (RANGE)


A: Tare table No. ANon 0Table No. 1 to 9

B: Scale entry BInhibit 0Enable 1Compulsory 2

C: Amount entry type CInhibited 0Open 1Preset 2Open and preset 3Delete 4

MRS = 000


[JOB#2232]PLU TAX STATUS PROGRAMMING (RANGE)


A: Sign A + 0– 1

B: Food stampable B


Food stampable 1

C: Taxable 4 C

Non taxable 0

Taxable 1

D: Taxable 3 D

Non taxable 0

Taxable 1

E: Taxable 2 E

Non taxable 0

Taxable 1

F: Taxable 1 F

Non taxable 0

Taxable 1

[JOB#1310]RATE PROGRAMMING

XXX: Function No.YYYY. YYYY: Rate

FunctionNo.

Function Entry range Remarks

1 (–)1

0 to 999999 (–) unit price 2 (–)2

3 (–)3

4 (–)4

5 %1

0 to 100.00 % rate 6 %2

7 %3

8 %4

65 Conversion 10 to 9999.9999 Rate 66 Conversion 2

67 Conversion 3

MRS = 0

Note: You must input the decimal key for fractional entries.

[JOB#2311]MISC KEY PROGRAMMING 1

XXX: Function No.

Function No. Function

1 (–)1

2 (–)2

3 (–)3

4 (–)4

5 %1

6 %2

7 %3

8 %4

YYYYYYXXXXXX2230

AB

@/FOR

CA/AT

@/FOR @/FORPLU CODE PLU CODE

No change (Same deta as start PLU)

SBTL

YYYYYYXXXXXX2231

ABC

@/FOR

CA/AT

@/FOR @/FORPLU CODE


SBTL

YYYYYYXXXXXX2232

ABCDEF

@/FOR

CA/AT

@/FOR @/FORPLU CODE


SBTL

SBTL1310 YYYY.YYYY@/FOR @/FOR CA/ATXXX

Function No. Rate

No change

SBTL2311 ABCDEF@/FOR @/FOR CA/ATXXX

Function No.

No change

A: Sign A

+ 0

– 1

B: Food stamp B

Non food stampable 0

Food stampable 1

C: Taxable 4 C

Non taxable 0

Taxable 1

D: Taxable 3 D

Non taxable 0

Taxable 1

E: Taxable 2 E

Non taxable 0

Taxable 1

F: Taxable 1 F

Non taxable 0

Taxable 1

MRS = 100000

[JOB#2312, 2322]HALO PROGRAMMING

XXX: Function No.A: Mantissa (0 to 9)B: Exponent (0 to 7) for (–) and Tax

Exponent (0 to 8) for RA/PO and each media

JOB#Function

No.Function Remarks

2312

1 (–)1

Item B is specificablewithin the range from 0 to7.

2 (–)2

3 (–)3

4 (–)4

32 TAX

64 RAItem B is specificablewithin the range from 0 to8.

65 RA2

66 PO

67 PO2

2322

61 CA1

Item B is specificablewithin the range from 0 to8.

62 CA2

86 CHK

87 CHK2

76 CH1

78 CH2

80 CH3

82 CH4

84 CH5

Entry range, system: A × 10B

MRS = 17 ((–)1-(–)4, TAX)18 (RA, RA2, PO, PO2, CA1, CA2, CHK, CHK2, CH1 - CH5)

[JOB#2313]MISCELLANEOUS KEY PROGRAMMING (% HALO)

XXX: Function No.YYY. YY: % HALO

FunctionNo.

Function Remarks

5 %16 %27 %38 %4

[JOB#2314]TEXT PROGRAMMING FOR MISC KEYS

XXX: FUNCTION NO.

Characters can be entered by using the character keys (direct key) orthe numeric keys (code entry). The key entry sequence for enteringone character by numeric keys is as follows:

XXX → 00 key XXX: CHARACTER CODE (3DIGITS)

Please refer to section 4 for further details.

F-NO. FUNCTION DEFAULT TEXT

1 (–)1

2 (–)2

3 (–)3

4 (–)4

5 %1

6 %2

7 %3

8 %4

9 NET1

10 TAXABLE1 ST

11 GROSS TAX1

12 REFUND TAX1

13 NET TAX1

14 EXEMPT TAX1

15 TAXABLE2 ST

16 GROSS TAX2

17 REFUND TAX2

18 NET TAX2

19 EXEMPT TAX2

20 TAXABLE3 ST

21 GROSS TAX3

22 REFUND TAX3

23 NET TAX3

24 EXEMPT TAX3

25 TAXABLE4 ST

26 GROSS TAX4

27 REFUND TAX4

28 NET TAX4

29 EXEMPT TAX4

SBTL23122322

AB@/FOR @/FOR CA/ATXXXFunction code

No change

SBTL2313 YYY.YY@/FOR @/FOR CA/ATXXX

No change

SBTL2314 @/FOR @/FOR CA/AT

Function number Max. 8 char.

All space

XXX Character key


30 GROSS M-TAX

31 REFUND M-TAX

32 NET M-TAX

33 NON GST SUBTOTAL

34 PST TOTAL (For "A" version)

35 GST TOTAL (For "A" version)

36 FS1 FORGIVE

37 FS2 FORGIVE

38 FS3 FORGIVE

39 TOTAL TAX

40 NET

41 NET2

42 COUPON PLU

43 VENDER COUPON UPC

44 ITEM VOID

45 SBTL VOID

46 MANAGER VOID

47 VOID MODE

48 REFUND

49 HASH VOID

50 HASH REFUND

51 NO SALE

52 VP COUNTER

53 BILL(SLIP) COUNTER

54 DRAWER COUNTER

55 PBAL

56 SERVICE

57 DEPOSIT

58 DEPOSIT REFUND

59 CUSTOMER

60 NET3 (SALES)

61 CASH

62 CASH2

63 FS SALE

64 RA

65 RA2

66 PO

67 PO2

68 CHECK CASHING

69 CHECK CHANGE

70 FS CHANGE

71 CONVERSION1

72 CONVERSION2

73 CONVERSION3

74 CONVERSION4

75 FS IN DRAWER

76 GROSS CHARGE1

77 REFUND CHARGE1

78 GROSS CHARGE2

79 REFUND CHARGE2

80 GROSS CHARGE3

81 REFUND CHARGE3

82 GROSS CHARGE4

83 REFUND CHARGE4

84 GROSS CHARGE5


85 REFUND CHARGE5

86 CHECK

87 CHECK2

88 CASH+CHECK IN DRAWER

89 CASH IN DRAWER

90VAT EXEMPT (For DOUGHNUTTAX Type1) (For "A" version)

91 AVERAGE (HOURLY REPORT)

92 GROUP1

93 GROUP2

94 GROUP3

95 GROUP4

96 GROUP5

97 GROUP6

98 GROUP7

99 GROUP8

100 GROUP9

101 PRICE 1 FOR UPC

102 PRICE 2 FOR UPC

103 PRICE 3 FOR UPC

104 (+)DEPT TOTAL

105 (–)DEPT TOTAL

106 HASH (+)DPT TOTAL

107 HASH (–)DPT TOTAL

108 BOTTLE (+)DPT TOTAL

109 BOTTLE (–)DPT TOTAL

110 SUBTOTAL

111 MDS SBTL

112 TOTAL

113 CHANGE

114 FS SBTL

115 FS TEND

116 FS CHANGE

117 ITEMS

118 COPY RCPT TITLE

119 DEPT REPORT TITLE

120 GROUP REPORT TITLE

121 PLU REPORT TITLE

122 CATEGORY REPORT TITLE

123 TRANSACTION REPORT TITLE

124 CID REPORT TITLE

125 CASHIER REPORT TITLE

126 HOURLY REPORT TITLE

127 DAILY NET REPORT TITLE

128 ZERO SALES REPORT TITLE

129 EAN REPORT TITLE

130 NON ACCESSED EAN TITLE

131 PBLU REPORT TITLE

132 PRICE CHANGE TITLE

133 FINAL

134 BALANCE

135 SLIP PRINT MESSAGE

136 BALANCE FORWARD

[JOB#2315]MISC KEY PROGRAMMING (%)

XXX: Function No.

A: % type ASubtotal % 0Item % 1

Function No. Function Remarks5 %16 %27 %38 %4

MRS = 0

[JOB#2316]MISC KEY PROGRAMMING (–)

XXX: Function No.

A: (–) type ASubtotal (–) 0Item (–) 1

Function No. Function Remarks1 (—) 12 (—) 23 (—) 34 (—) 4

MRS = 0

[JOB#2320]MEDIA KEY PROGRAMMING

XXX: Function No.

FunctionNo.

Function A B C D E F G H

61 CA 162 CA 276 CH 178 CH 280 CH 382 CH 484 CH 586 CHK87 CHK256 SERVICE

115 FS TEND133 FINAL

Items marked with an ( ) are programmable.

A : Not used (Fixed at "0")

B: Bill (Slip) print BNoncompulsory 0Compulsory 1

B: Footer print on receipt BNo 0Yes 1

C: Non-add code entry CNon compulsory 0Compulsory 1

D: Change due DEnable 0Disable 1

E: VP ENon compulsory 0Compulsory 1

F: Drawer opening FYes 0No 1

G: Entry of amount tended GNon compulsory (Cash, Check)Inhibit (CH1 to CH5)

0

Compulsory 1

MRS=0000000

[JOB#2321]MEDIA KEY FUNCTION PROGRAM (AMOUNT HALO)

XXX: Function No.YYYYYYYYY: Limitation amount

Func. No.

Function Entry range MRS

89 CID (Sentinel) 0 to 9999999.99 9999999.9969 CHK CHANGE 0 to 999999.99 999999.9965 CA/CHK 0 to 999999.99 999999.99

[JOB#2326]MEDIA KEY PROGRAMMING – 2

XXX: Function No.

Function No. Function61 CA 162 CA 276 CH 178 CH 280 CH 382 CH 484 CH 586 CHK87 CHK2

SBTL2315 A@/FOR @/FOR CA/ATXXX

No change

SBTL2316 A@/FOR @/FOR CA/ATXXX

No change

SBTL2320 ABCDEFGH@/FOR @/FOR CA/ATXXX

No change

SBTL2321 YYYYYYYY@/FOR @/FOR CA/ATXXX

No change


No change

ABCD2326 XXX

A: Taxable 4 delete A

No 0

Yes 1

B: Taxable 3 delete B

No 0

Yes 1

C: Taxable 2 delete C

No 0

Yes 1

D: Taxable 1 delete D

No 0

Yes 1

MRS=0000

[JOB#1500]CASHIER CODE DEFINITION

XXX: Cashier No.= 1 - 99YYYY: Cashier code = 00 - 99

MRS = Cashier code 1 - 4.

[JOB#1514]CASHIER NAME PROGRAMMING

YYYY: Cashier code = 01 - 99

Characters can be entered by using the character keys (direct key) orthe numeric keys (code entry). The key entry sequence for enteringone character by numeric keys is as follows:

XXX 3 00 KEY XXX: Character code (3 digits)

Please refer to section 4.Max. 8 charactersMrs = ’Space’

[JOB#2510]CASHIER PROGRAMMING

YYYY: Cashier code = 01~99

A: Drawer No. H

Not open 0

Drawer No. 1-2

MRS = 1

[JOB#2610]DATE SETTING

XXYYZZ: Date (Year-Month-Day/Day-Month-Year/Month-Day-Year)

The date entry format complies with the setting of SRV JOB#912.MRS = 010100

[JOB#2611]TIME SETTING

XX: Hour (00 - 23)YY: Minute (00 - 59)MRS = 0

[JOB#2612]MACHINE NUMBER SETTING

XXXXXX: Machine number (0 - 999999)MRS = 0

[JOB#2613]CONSECUTIVE NUMBER SETTING

XXXX: Consecutive number (0000 - 9999)MRS = 0000

[JOB#2614]LOGO TEXT PROGRAMMING

X: 1 - 6 1 (24 char.)2 (24 char.)3 (24 char.)4 (24 char.)5 (24 char.)6 (24 char.)

Characters can be entered by using the character keys (direct key) orthe numeric keys (code entry).The key entry sequence for entering one character by numeric keysis as follows:

XXX 00 Key XXX: Character code (3 digits)Please refer to section 4 for further details.

MRS =

NOTE: This programming is related to SRV JOB# 912D preset."6-line header": All 6 lines are preset."3-line header": Upper 3 lines (1st-3rd line) are preset."Graphic logo and 3-line footer": Lower 3 lines (4 th - 6 th

line) are preset"3-line footer": Lower 3 lines (4th-6th line) are preset."3-line header and 3-line footer": All 6 lines are preset. (1st-

3rd: Header, 4th-6th:Footer)

"Graphic logo only": No line is preset

SBTL1500 YY@/FOR @/FOR CA/ATXX

No change

SBTL1514 @/FOR @/FOR CA/AT

All space

YY Character key

SBTL2510 A@/FOR @/FOR CA/ATYY

No change

2610 @/FOR CA/ATXXYYZZ

0

2611 @/FOR CA/ATXXYY

0

2612 @/FOR CA/ATXXXXXX

0

2613 @/FOR CA/ATXXXX

2614 Character key@/FOR @/FOR SBTL CA/ATX

Position code

All space

[JOB#2615]

SLIP PRINTER OPTIONSProgramming of the limits to No. of times of validation printing.

VV: Initial slip feed line = 0 - 64XX: Slip print max. line No. = 0 - 99Y: No. of times of validation printing = 0 - 9 X: Not used (Fixed at "0")

MRS = 009910

Note: Max. line number of the slip must be set to a value less thanthe length of the of bill included the initial feed line.

[JOB#2616]OPTIONAL FEATURE

XX: 1 MRS = 00000000

A: OP X/Z report AEnable 0Disable 1

B: PO operation in REG mode BEnable 0Disable 1

C: Refund type of sale function in REGmode

C

Enable 0Disable 1

D: "RFND" key entry in REG mode DEnable 0Disable 1

E: Direct void function in REG mode EEnable 0Disable 1

F: In direct void in REG mode FEnable 0Disable 1

G: Subtotal void in REG mode GEnable 0Disable 1

H: Refund VP (SLIP only) HNon compulsory 0Compulsory 1

XX: 2 MRS = 00000000

A: The first last item void AEnable 0Disable 1

B, C: Not used (Fixed at "00")

D: Printing of the number of purchases DNo 0Yes 1

E: Time print EYes 0No 1

F: Printing of journal FFull print 0Journal select 1

G: Item VP (SLIP only) GEnable 0Disable 1

H: (–) VP (SLIP only) HNon compulsory 0Compulsory 1

XX: 3 MRS = 00000000

A: Zero skip in UPC report AYes 0No 1

B : Not used (Fixed at "0")

C: Zero skip in Cashier report CYes 0No 1

D: Zero skip in Transaction report DYes 0No 1

E: Zero skip in Dept. report EYes 0No 1

F: Zero skip in PLU report FYes 0No 1

G: Zero skip in Hourly report GYes 0No 1

H: Zero skip in Daily net report HYes 0No 1

XX: 4 NOT USED MRS = 00000000XX:5 MRS = 00000000

A,B,C,D,E: Not used (Fixed at "00000")

F: UPC price shift system FMGR & REG 0MGR 1

G: UPC price shift system GAuto 0Manual 1

H: Return timing at "Auto" (XX:5-G = 0) HBy one item 0By one receipt 1

X: 6 NOT USED MRS = 00000000X: 7 MRS = 00000000

2615 @/FOR CA/AT

0

WXXYZ

@/FOR @/FOR SBTL CA/ATXX

No change

ABCDEFGH2616

A, B: Not used (Fixed at "00")

C: No sale in REG mode CEnable 0Disable 1

D: Finalization in REG mode whenSBTL is zero

D

Enable 0Disable 1

E: Printing of item in PBLU transactionon SLIP

E

Yes 0No 1

F, G, H: Not used (Fixed at "000")X: 8 MRS = 00000000

A, B, C, D: Not used (Fixed at "0000")

E: Validation of check cashing (SLIP ONLY) E

Non compulsory 0

Compulsory 1

F: Validation of RA (SLIP ONLY) F

Non compulsory 0

Compulsory 1

G: Validation of PO (SLIP ONLY) G

Non compulsory 0

Compulsory 1

H: Not used (Fixed at "0")X: 9 MRS = 00000000

A, B: Not used (Fixed at "00")

C: BIRTHDAY print on printer C

Yes 0

No 1

D, E, F, G, : Not used (Fixed at "0000")

H: Footer Graphic logo printing at theend of receipt

H

No 0

Yes 1

XX:10 MRS = 00000000A,B: Not used (Fixed at "00")

C: Learning function UPC entry C

Yes 0

No 1

D, E, F, G, H: Not used (Fixed at "00000")

X: 11 NOT USED MRS = 00000000XX:12 MRS = 00000000

A, B, C, D, E, F, G: Not used (Fixed at "0000000")

H: Price change function in REG mode H

Enable 0

Disable 1

XX:13 MRS = 00000000A,B,C: Not used (Fixed at "000")

D: Printing of price shift text on theReceipt/Journal

D

Yes 0

No 1

E: Not used (Fixed at "0")

F: Treating EAN8 code 200 as PLU F

Yes 0

No 1

G: Not used (Fixed at "0")

H: Price entry after ISBN or ISSN H

Compulsory 0

Inhibited 1

[JOB#2617]PROGRAMMING THE TIME INTERVAL FOR THE TILL TIMER

XXX: 0 - 255 sec

MRS = 000

[JOB#2618]SCALE TABLE PROGRAMMING

X: Table No. = 1 - 9

YYYY: Weight = 0 - 99.99 ( Enter without decimal point.)

MRS = 0

[JOB#2619]HOURLY REPORT (Starting time)

a: Memory type A

30 minutes (24 hour) 0

60 minutes (24 hour) 1

bb: Starting time (hour): 00 - 23

ex)

Case 1.

X1 Hourly report (#160) (30 min, start time = 7]

2617 @/FOR CA/ATXXX

0

YYYY

0

2618 XUPC code

CA/ATSBTL

@/FOR @/FOR

2619 @/FOR CA/ATabb

0

2619 @/FOR CA/AT007

[JOB#2620]STACK REPORT

XX: JOB#SSSSSS: Start codeEEEEEE: End code

JOB# REPORT NAME TYPE00 General07 UPC zero sales09 All UPC ALL10 DEPT.13 DEPT. All group20 PLU RANGE -127 PLU zero sales RANGE -129 PLU category RANGE -130 Transaction31 CID50 All cashier60 Hourly RANGE -2 (only X report)60 Hourly ALL70 Daily net80 PBLU RANGE-2

[ ]

A max of 70 steps are programmable. "1 step" means the memorysize used for one no range type JOB#.

The RANGE-1 type JOB# means "8 steps".

The RANGE-2 type JOB# means "6 steps".

For example)

The memory size for programming JOB#00, 20 and 50 is 10 steps.(ie. 1 step for JOB#00, 8 steps for JOB#20, and 1 step for JOB#50. )

[JOB#2630, 2631, 2632]SECRET CODE PROGRAMMING

#2630: PGM1 mode

#2631: X1/Z1 mode

#2632: X2/Z2 mode

XXXX: Secret code = 0000 - 9999

If "0" is entered, "compulsory secret code entry" is canceled.

MRS = 0

[JOB#2642]VP TEXT PROGRAMMING

X: Position code = 1 - 3

1 Block Max. 24 characters

MRS = " "" ""FOR DEPOSIT ONLY"

[JOB#2643]SLIP TEXT PROGRAMMING

X: Position code = 1 - 3

1 Block Max. 24 characters

MRS = "SPACE""SPACE""SPACE"

[JOB#2690]THE ASSIGNMENT OF RS232 FUNCTION BY EACH DEVICE

CAUTION: Do not assign two different devices to the same channelNo.

X: 1 MRS = 0000

A: Channel No. for ON-LINE ANo 0Channel No. (1 or 8) 1 or 8

B: Channel No. for Print data sending BNo 0Channel No. (1 or 8) 1 or 8

C: Channel No. for Scale CNo 0Channel No. (1 or 8) 1 or 8

D: Not used (Fixed at "0")X: 2 MRS = 0000

A: Channel No. for Barcode reader ANo 0Channel No. (1 or 8) 1 or 8

B,C,D: Not used (Fixed at "000")X:3 MRS = 0000

A: Not used (Fixed at "0")

B: Channel No. for Slip printer (TM295) BNo 0Channel No. (1 or 8) 1 or 8

C,D:Not used (Fixed at "00")

2620 @/FOR

XX @/FOR SSSSSS @/FOR EEEEEE

All delete

No range

Next JOB# (max.=20)

SBTL CA/AT

2630 @/FOR CA/ATXXXX

0

26312632

Characterkey

All space

2642 XPosition code

CA/ATSBTL

@/FOR @/FOR

Characterkey

All space

2643 XPosition code

CA/ATSBTL

@/FOR @/FOR

2690 ABCD@/FOR @/FOR SBTL CA/ATX

0

Channel No.: 0 = No connection1 = Standard port 22-7 = Not used8 = Standard port 1

NOTE: There can be only 2 devices supported by the ECR at anyone time.Will ENTRY ERROR is occurred when a device has been setas the same channel that is used by another device.

[JOB#2691]BARCODE READER PROGRAMMING

W: Data bitW

8 bits 07 bits 1

X: Parity bit XEven 0Odd 1Non 2

Y: Stop bit Y2 bits 01 bit 1

Z: Transmission speed Z4800 bps 09600 bps 119200 bps 2

MRS = 1110(For ER-A6HS1)

[Job# 2710]TAX TABLE PROGRAMMING

72 BREAKPOINTS CAN BE PROGRAMMED FOR EACH TAX-TABLE.

(When the interval between break point is 1 dollar or more and lessthan 100 dollar, 36 breakpoints is programmed for each table.)

DEPRESSION OF THE SBTL KEY AT THE FOLLOWING POINTSWILL RESULT IN A TAX TABLE DELETE OPERATION.

A: INTERVAL BETWEEN BREAKPOINTS IS = 11 DOLLAR OR MORE AND LESS THAN 100 DOLLAR

INTERVAL BETWEEN BREAKPOINTS IS = 0BELOW 1 DOLLAR

B: TABLE 1 PROGRAMMING = 1TABLE 2 PROGRAMMING = 2TABLE 3 PROGRAMMING = 3TABLE 4 PROGRAMMING = 4

TAX RATE : 0.0000 - 99.9999CYCLE : 0 - 9999INITIAL TAX : 0 - 999LOWER TAX LIMIT : 0 - 99999BREAK POINT : 0 - 99999

MRS = NO TAX

[JOB#2711]TAX RATE PROGRAMMING

DEPRESSION OF THE ST KEY AT FOLLOWING POINTS WILLRESULT IN A TAX TABLE DELETE OPERATION.

A: Tax programming ATax1 1Tax2 2Tax3 3Tax4 4

xxx.xxxx: % TAX rate = 0.0000-999.9999%

LOWER TAX LIMITATION = 0.00 to 999.99

(This is invalid in VAT system.)

MRS = 0

[JOB#2715]QUANTITY FOR DOUGHNUT EXEMPT ( For Canadian TAX )

XX: Quantity for doughnut TAX exempt = 0 - 99

MRS = 0

[JOB#2810]PBLU code ( The range programming of available PBLU codes)

XXXX:Start code = 1 - 9999

YYYY:End code = 1 - 9999

MRS = 0001(Start code) / 9999(End code)

2691 CA/AT@/FOR WXYZ

0

AB

Declaration of TAX TAX rate

XXXX

Initial TAXCycle

XXXXX

Break pointLower TAX limit

2710

XXX

XXXXX

@/FOR

CA/AT

@/FOR @/FORXX.XXXX

@/FOR @/FOR

@/FOR @/FOR


Lower tax limitfor add tax.

When lower taxlimit is 0.

2711 A XXX.XXXX

XXXXX

@/FOR

CA/AT

CA/AT

@/FOR @/FOR

2715 CA/AT@/FOR XX

0

2810 @/FOR XXXX CA/AT@/FOR YYYY

0

[JOB#2900]

Note:(This JOB must be performed at X2/Z2 mode position.)

AUTO KEY SETTING

(Auto key function)

• This machine has [AUTO] key functions which can be programmedby the following key-sequence.

• When [AUTO] key is depressed, the machine works the same asthe programmed key-sequence programmed.

<Example>

Mode switch

⇓

(X2/Z2)

(REG)

(X2/Z2)

(REG)

[JOB#2910, 2911]Training mode start (#2910), End (#2911)

<Training mode>

All operations is same as REG-mode operation.In the training mode, the consecutive number is printed the as samenumber on receipt/journal printer and slip printer.In the training mode, the consecutive number is incremented by eachtransaction.

[JOB#2990]THERMAL PRINTER PROGRAMMING

X, Y: Not used (Fixed at "10")

ZZ: Selecting of light and shade ZZ

80% for standard 00

90% standard 50

100% standard 99

MRS = 1050

Entries for XY will always result in a setting of "10"(It is always set as "10" even if "00"is entered.)

3. Programming by direct key entry

1) PRICE PROGRAMMING for DEPT.

XX: DEPT. code = 01 to 50

YYYYYY: UNIT PRICE (Max. 6 digits)

MRS = 0

If [DPTn] (same as the displayed department number) or [DEPT#]is depressed, the programming mode is changed from "PRICEPROGRAMMING" to "FUNCTION PROGRAMMING" (from"FUNCTION PROGRAMMING" to "PRICE PROGRAMMING").

2) FUNCTION PROGRAMMING for DEPT.

XX: DEPT. code = 01 to 50

A: Sign A

+ 0

– 1

B: Food stamp B


Food stampable 1

C: Taxable4 C

Non taxable 0

Taxable 1

D: Taxable3 D

Non taxable 0

Taxable 1

2900 (Free key)AUTO

Max.25

@/FOR CA/AT

AUTO2

AUTO3

AUTO4

AUTO5

AUTO

AUTO2

AUTO3

AUTO4

AUTO5

Delete

AUTO10 AUTO10

2900 @/FOR AUTO PLU1 100 DEPT2 AUTO CA/AT

Key entry R/J Display Comment

AUTO PL000001 $1.10

PL000001 $1.00

PL0000001 same as entryPLU11.10

1

10

100

DEPT02 1.10

same as entry1

same as entry0

same as entry0

same as entryDEPT2

2900 @/FOR AUTO2 PLU1 100 DEPT2 CA/ATAUTO2

Key entry R/J Display Comment

DEPT 1 DEPT01 DEPT01 1.10

100

CHANGE 0.00

same as entry1

same as entry0

same as entry0

same as entryCA/AT

AUTO 2

$1.00

***TOTAL $1.00

CASH $1.00

CHANGE $0.00

10

1

2910/2911 @/FOR CA/AT

0

2990 XYZZ@/FOR CA/AT

DEPTn

Not changed

For next code

YYYYYY

DEPT#XX

CA/ATSBTL

DEPTn

Not changed

For next code

ABCDEFGHI

DEPT#XX

SBTL CA/AT

E: Taxable2 E

Non taxable 0

Taxable 1

F: Taxable1 F

Non taxable 0

Taxable 1

G: SICS Function G

Normal 0

Single item cash sale 1

Single item finalize 2

H: Limitation (Mantissa) = 0~9

I: Limitation (Exponent) = 0~7

MRS = NORMAL, 17 HALO

If [DPTn] (same as the displayed department number) or[DEPT#] is depressed, the programming mode is changed from"PRICE PROGRAMMING" to "FUNCTION PROGRAMMING"(from "FUNCTION PROGRAMMING" to "PRICE PROGRAM-MING").

Double depression of the [DPTn] or [DEPT#] key is necessaryfor the first entry.

3) PRICE & MODIFY PROGRAMMING for (–) KEYS.Mode : PGM1 / PGM2

XXXXXX: UNIT PRICE (Max. 6 digits)

MRS = 0

If the same [(–)n] key is depressed, the programming mode ischanged from the "PRICE PROGRAMMING" to "FUNCTION PRO-GRAMMING" (from "FUNCTION PROGRAMMING" to "PRICEPROGRAMMING").

4) FUNCTION PROGRAMMING for (–) KEYS.Mode : PGM2

A: Sign A

+ 0

– 1

B: Food stamp B


Food stampable 1

C: Taxable4 C

Non taxable 0

Taxable 1

D: Taxable3 D

Non taxable 0

Taxable 1

E: Taxable2 E

Non taxable 0

Taxable 1

F: Taxable1 F

Non taxable 0

Taxable 1

G: Not used (Fixed at "0")

H: Limitation (Mantissa) = 0~9

I: Limitation (Exponent) = 0~7

MRS = NORMAL, 17 HALO

If the same [(–)n] key is depressed, the programming mode ischanged from the "PRICE PROGRAMMING" to "FUNCTION PRO-GRAMMING" (from "FUNCTION PROGRAMMING" to "PRICEPROGRAMMING").

5) PLU PRESET PRICE SETTINGMode : PGM1 / PGM2

XXXXXX: PLU CODE (1 to 999999)YYYYYY: UNIT PRICE (6 digits)


MRS = 0

If the [PLU] or [PLUn] key is depressed, the programming mode ischanged from the "PRICE PROGRAMMING" to "ATTRIBUTEPROGRAMMING" and is changed to the "PLU ASSOCIATIONPROGRAMMING" by depressing the same key again.(Caution!!)The associated department is changed if the operator depressesthe [DPTn] key instead of [PLUn] key by mistake at this program-ming step.

6) PLU ASSOCIATION TO DEPARTMENTSMode : PGM1 / PGM2

XXXXXX: PLU CODE (1 to 999999)YY: Dept. code (1 to 50)If the record of entered PLU code is not in PLU file at this program-ming, it will be created in PLU file.

MRS = 01

If the [PLU] or [PLUn] key is depressed, the programming modeis changed from the "PRICE PROGRAMMING" to "ATTRIBUTEPROGRAMMING" and then changed to the "PLU ASSOCIA-TION PROGRAMMING" by depressing the same key again.

Not changed

XXXXXX CA/ATSBTL(-)n

Not changed

ABCDEFGHI(-)n (-)n CA/AT@/FOR

Not changed

XXXXXXPLU code

for next code

YYYYYYPLU

PLUn

SBTL CA/AT

XXXXXXPLU code

PLU delete

PLU

PLUn

for next code

DPTn

VOID

YY

Not changed DEPT#

SBTL

CA/AT

Note:The associated department is changed if the operator depress[DPTn] key instead of [PLUn] key by mistake at this program-ming step.

Triple depression of the [PLU] or [PLUn] key is necessary for thefirst entry.

7) PROGRAMMING OF PLU/SUBDEPTMode : PGM2

XXXXXX: PLU CODE (1 to 999999)

A: Sign A

+ 0

– 1

B: Food stamp B


Food stampable 1

C: Taxable4 C

Non taxable 0

Taxable 1

D: Taxable3 D

Non taxable 0

Taxable 1

E: Taxable2 E

Non taxable 0

Taxable 1

F: Taxable1 F

Non taxable 0

Taxable 1

G: Amount entry type G

Inhibited 0

Open 1

Preset 2

Open and preset 3

Delete 4


MRS = 002

* If the [PLU] or [PLUn] key is depressed, the programming modeis changed from the "PRICE PROGRAMMING" to "ATTRIBUTEPROGRAMMING" and then changed to the "PLU ASSOCIA-TION PROGRAMMING" by depressing the same key again.

Double depression of [PLU] or [PLUn] key is necessary for thefirst time.

8) UPC PRESET PRICE SETTINGMode:PGM1/PGM2


YYYYYY: Unit price (6 digits)



The default value is set when the new UPC record is created.

At this time, Price1 is shown.If the [UPC] key is depressed, the programming mode is changedfrom "PRICE PROGRAMMING" to "ATTRIBUTE PROGRAM-MING" and then changed to the "UPC ASSOCIATION PRO-GRAMMING" by depressing the same key again.

9) PROGRAMMING OF UPCMode : PGM2


A: Sign A+ 0- 1

B: Food stamp BNo 0Yes 1

C: Taxable4 CNon taxable 0Taxable 1

D: Taxable3 DNon taxable 0Taxable 1

E: Taxable2 ENon taxable 0Taxable 1

F: Taxable1 FNon taxable 0Taxable 1

G: Record delete method GDelete at X/Z non-accessedUPC deleting JOB

0

Non delete 1Delete now 2

If the record of the entered UPC code is not in the UPC file at thisprogramming step, the UPC code is created.

MRS = nothing ( Default = 0000000)

The default value is set when the new UPC record is created.

Not changed

XXXXXX

PLU code

for next code

ABCDEFG @/FOR CA/ATPLU

PLUn

XXXXXXXXXXXXX UPC

(Scanning)

YYYYYY

No change

P1

CA/ATSBTL

P2

P3(Pricel shift)

(Pricel)

XXXXXXXXXXXXX UPC

(Scanning)

ABCDEFG

No change

CA/AT@/FORUPC code

If the [UPC] key is depressed, the programming mode ischanged from the "PRICE PROGRAMMING" to "ATTRIBUTEPROGRAMMING" and then changed to the "UPC ASSOCIA-TION PROGRAMMING" by depressing the same key again.

Either "Double depression of the [UPC] key" or "a depression of[UPC] key after scanning" is necessary for the first entry.

10) UPC ASSOCIATION TO DEPARTMENTSMode : PGM1/PGM2


YY: DEPT. code = 1 to 50


MRS = nothing ( Default = 01)

The default value is set when the new UPC record is created byanother programming JOB.

If the [UPC] key is depressed, the programming mode ischanged from the "PRICE PROGRAMMING" to "ATTRIBUTEPROGRAMMING" and then changed to the "UPC ASSOCIA-TION PROGRAMMING" by depressing the same key again."Triple depression of the [UPC] key" or "Double depression ofthe [UPC] key after scanning" is necessary for the first entry.

11) PROGRAMMING RATE FOR %KEY.Mode : PGM1 / PGM2

XXX.XX: 0.00 to 100.00

MRS = 0.00%

If the same [%n] key is depressed, the programming mode ischanged from the "RATE PROGRAMMING" to "FUNCTION PRO-GRAMMING".

12) PROGRAMMING FOR %KEY.Mode : PGM2

A: Sign A+ 0– 1

B: Food stamp BNon-food stampable 0Food stampable 1

C: Taxable4 CNon taxable 0Taxable 1

D: Taxable3 DNon taxable 0Taxable 1

E: Taxable2 ENon taxable 0Taxable 1

F: Taxable1 FNon taxable 0Taxable 1

MRS = 100000

If the same [%n] key is depressed, the programming mode ischanged from the "RATE PROGRAMMING" to "FUNCTION PRO-GRAMMING" (from "FUNCTION PROGRAMMING" to "PRICEPROGRAMMING").

13) PROGRAMMING RATE FOR CONVERSION KEYMode : PGM1 / PGM2

XXXX.XXXX: 0.0000 to 9999.9999MRS = 0.00000

14) PROGRAMMING FOR MEDIA KEYS &FUNCTION KEYS.Mode : PGM2

A: Mantissa (0 to 9)

B: Exponent (0 to 8)

MRS = 18 digits. (RA, PO, CASH2, CHn, CHKn)17 digits. (TAX)

In case of the Manual TAX HALO programming:At the first entry, the [TAX]-key must be pushed two times.After entry of the [@/FOR]-key, the [TAX]-key is only requiredone time after.

XXXXXXXXXXXXX UPC

(Scanning)UPC delete

DEPTn

DEPT#

VOID

Not changed

YY

CA/AT

SBTL

UPC code

Not changed

SBTL CA/AT%n XXX.XX

Not changed

ABCDEF%n %n CA/AT@/FOR

CNV1

Not changed

XXX.XXX

CNV2

CNV3

CA/ATSBTL

RA

PO

CASH2

CHn

CHKn

TAX

AB CA/AT@/FOR

TAX TAX

15) DATE, TIME PROGRAMMING.Mode : PGM2

DATE: date entry format follows SRV JOB#912-A settings (6 digits)TIME: 24 hour system (4 digits)

MRS = DATA: 01/01/00TIME: 00:00

16) TAX TABLE PROGRAMMING

72 BREAKPOINTS CAN BE PROGRAMMED FOR EACH TAX-TABLE.

(If the interval between break points is 1 dollar or more and less than 100dollar, a maximum of 36 breakpoints is programmed for each table.)

DEPRESSION OF THE SBTL KEY AT THE FOLLOWING POINTSWILL RESULT IN A TAX TABLE DELETE OPERATION.

A: INTERVAL BETWEEN BREAKPOINTS1 DOLLAR OR MORE AND LESS THAN 100 DOLLAR = 1BELOW 1 DOLLAR = 0

B: TAX TABLE No.TABLE 4/TABLE 3/TABLE 2/TABLE 1 = 4/3/2/1

TAX RATE : 0.0000 - 99.9999CYCLE : 0 - 9999INITIAL TAX : 0 - 999LOWER TAX LIMIT : 0 - 99999BREAK POINT : 0 - 99999

MRS = NO TAX

4. Character assignment method

∼ Using the alphabet assignment method ∼

Programming key layout

Using the ten key of the ECR

Note: The 00 key is used to enter each 3 digit alpha code.

Examples

“ A (Shift-2) “ A = “ is set

(DC) “ A = A (double character code) is set

(Shift) “ A = a (lowercase letter) is set

Once the (Shift) key is pressed, it stays down until it is pressedagain.

XXXXXX

HHMM

DATA

TIME

#

XXXXXX@/FORAB @/FOR


XXX@/FORXXXX @/FOR

Initial TAXCycle

XXXXX@/FORXXXXX @/FOR

Break pointLower TAX limit

CA/AT

TAX

@/FOF SBTLPush alphabet

Repeat

:

+

ZWRMHC

YVQLGB

XUPKFA

SNID

TOJE

?

(BS)(DC)

(Space)1 2 3

4 5 6

7 8 9

O

< >

;

-

#

@

=

?

)

%$

/

.

&

!

BACKSpace

( )< ( )<

( )

( ) ( )( )

( ) ( )- §

æ

Æ

£Pt

(Shift-2) (Shift)

ø ç

Φ

( ) : Function key

(DC) : Double character code entry key (One-shot)(Shift) : Character shift key (Stay-down)(Shift-2) : Mark key (One-shot)(BS) : Back space key

@/FOR 00XXX

3 digitsSBTL

Repeat

<Character Code Table for text programming>

CODE CHARACTER001 à002 â003 ê004 î005 ì006 í007 ô008 ó009 û010 ú011 œ012 ü013 ú014 ö015 ó016 Λ017 Ψ018 Γ019 ..

020 Ω021 ∆022 Θ023 Ξ024 Π025 Σ026 Υ027 Φ028 Ü029 Ú030 Ö031 Ó032 (Space)033 !034 "035 #036 $037 %038 &039 ’040 (041 )042043 + 044 , 045 –046 .047 /048 0049 1

CODE CHARACTER050 2051 3052 4053 5054 6055 7056 8057 9058 :059 ;060 <061 =062 >063 ?064 @065 A066 B067 C068 D069 E070 F071 G072 H073 I074 J075 K076 L077 M078 N079 O080 P081 Q082 R083 S084 T085 U086 V087 W088 X089 Y090 Z091 Ä092 Ö093 Ü094 ^ 095 _096097 a098 b

CODE CHARACTER099 c100 d101 e102 f103 g104 h105 i106 j107 k108 l109 m110 n111 o112 p113 q114 r115 s116 t117 u118 v119 w120 x121 y122 z123 124 |125 126 ß127128 !!129 1

130 2

131 3

132 4

133 1⁄2134 FT

135 ←136 →137138139140141 F

142 T

143 ↓144 ç145 O

146 ¿147 Ù

CODE CHARACTER148 à149 Æ150 φ151 Å152 ¤153 é154 è155 Pt156 ¡157 Ñ158 ò159 £160 ¥161162 163 164165 .

166 T 1

167 T 2

168 T 3

169 T 4

170 1 2

171 1 3

172 1 4

173 2 3

174 2 4

175 3 4

176177 Á178 Í179180 A181 a182 E183 e184 I185 i186 U187 u188

189

190191 Š192193194195

196

CODE CHARACTER

197

198

199

200

201

202

203

204

205

206

207

208

209

210

211 š

212

213

214

215

216

217

218 ′219

220221222223224 *

225 §226 ∅227 ^ 228 ↑229 ]230 [

231

232 ä233 ö234 ü235 æ236 å237 É238 ñ

253 DC

(DC) : Double Code: ECR Control Character (Not used for text)

Fig. 7-2

CHAPTER 3. OP X/Z, X1/Z1,X2/Z2 MODE

The following categories of reports can be printed by the ECR.

OP X/Z reports: These reports are taken by operators in order toreport their own sales data.

XI/Z1 reports: These reports are taken by the supervisor or man-ager in order to check and report daily sales totalsat that point.

X2/Z2 reports: These reports are taken by the owner or managerin order to check and report periodic (weekly ormonthly) totals.

MGR/Flash-read: These reports are taken by the owner or managerin order to check and display daily sales totals atthat point.

To print reports, use the following key entry sequence

MODE *1

OP X/Z X1/Z1 X2/Z2 JOB# or KEY DATA FOR READING

REPORT NAME X Z X1 Z1 X2 Z2 *3 NOTE

GENERAL 00 ---

UPC (All) 09 ---

(Pick up) 09 PICK UP *4

UPC BY DEPT. 01 DEPT CODE

UPC ZERO SALES (All) 07 ---

(By DEPT.) 07 DEPT CODE

DEPT./GROUP 10 ---

IND. GROUP 12 GROUP No.

GROUP TOTAL 13 ---

PLU BY RANGE 20 PLU CODE *2

PLU BY DEPT. 21 DEPT CODE

PLU ZERO SALES (All) 27 ---

(By DEPT.) 27 DEPT CODE

PLU PRICE CATEGORY 29 PRICE *2

TRANSACTION 30 ---

CID 31 ---

ALL CASHIER 50 ---

IND. CASHIER 51 ---

HOURLY (All) 60 ---

(Range) 60 TIME *2

DAILY NET 70 ---

PBLU 80 PBLU CODE *2

PBLU BY CASHIER 81

STACKED REPORT 90 ---

DEPT. SALES (Frash-read) DEPTn --- *5

CID (Frash-read) [@/FOR] --- *5

DAILY MET SALES (Frash-read) [SBTL] --- *5

NON-ACCESSED UPC 105 ---

DELETE OF NON-ACCESSED UPC 105(*) ---

105(*) PICK UP *4

(*) At this operation, the non-accessed UPCs data are printed anddeleted.

To stop the printing reports:The printing of all reports can be stopped by the following operation.

Set the mode switch to "MGR" to cancel.

Note) When the printing is stopped, the consecutive number or Zcounter doesn’t return to the original value.For Z reports, Memory is not reset when canceled.

*1 X1: Daily X reportX2: Periodic X report

Z1: Daily Z reportZ2: Periodic Z report

*2 The time interval range and PLU code range can be specified byentering the start and end numbers according to the followingprocedure. When specifying a single time interval or PLU code,the start number has only to be entered.

*3 When 2 is entered in the third digit of a job code, periodic reportsare printed.

Example: Daily general report; job code 100Periodic general report; job code 200

JOB# @/FOR CA/AT

Reading

Resetting

Range is required

All

Start No. End No.@/FORXXXXXX XXXXXX

*4 (Pick-up reports from UPC utems)

Those reports asterisked (*4) in the above list can pick up some UPCdata which you very want to watch from the UPC file.

*5 Reading display only

KEY CL (Display amount) (Display initialize)

KEY DEPT = DEPTn keyCID = @/For keyDaily Net = ST key

• An individual report is printed on the receipt and journal when theCA/AT key is pressed.

• Pressing the decimal point key just after the entry of a job codeclears the corresponding data in the ECR. (Z report)(When printing those reports for which no Z reports can be taken,the decimal point key cannot be pressed after the entry of a jobcode.)

• When the decimal point key is not pressed after the entry of a jobcode, the corresponding data is held in the ECR. (X report)

XXXXXXXXXXXXX

Pick up (to the number of records in Pick-up file)

EAN code

(Scanning);Previous UPC codes picked up

;All UPC data

@/FOR CA/AT

@/FOR CA/AT

@/FOR CA/AT

COPYRIGHT 2000 BY SHARP CORPORATIONAll rights reserved.Printed in Japan.

No part of this publication may be reproduced,

stored in a retrieval system, or transmitted,in any form or by any means,

electronic, mechanical, photocopying, recording, or otherwise,

without prior written permission of the publisher.

SHARP CORPORATIONInformation Systems GroupQuality & Reliability Control CenterYamatokoriyama, Nara 639-1103, Japan

2000 December Printed in Japan

MODEL ER-A450Tmscashdrawer.com/docs/Sharp/SHARP ERA450TUPM.pdfELECTRONIC CASH REGISTER MODEL...

Documents

Transcript of MODEL ER-A450Tmscashdrawer.com/docs/Sharp/SHARP ERA450TUPM.pdfELECTRONIC CASH REGISTER MODEL...