MODEL ER-A450T - Barcode Distributor ERA450TUPM.pdf · ELECTRONIC CASH REGISTER MODEL ER-A450T (For...
Transcript of MODEL ER-A450T - Barcode Distributor ERA450TUPM.pdf · ELECTRONIC CASH REGISTER MODEL ER-A450T (For...
ELECTRONICCASH REGISTER
MODEL ER-A450T(For "U" & "A" version)SRV KEY : LKGIM7113BHZZPRINTER : PR-45M
SHARP CORPORATIONThis document has been published to be usedfor after sales service only.The contents are subject to change without notice.
CHAPTER 1. SERVICE (SRV) MODE . . . . . . . . . . . . . . . . . . . . . . . . . . 1
CHAPTER 2. PROGRAM (PGM2/PGM1) MODE. . . . . . . . . . . . . . . . . 17
CHAPTER 3. OP X/Z, X1/Z1, X2/Z2 MODE . . . . . . . . . . . . . . . . . . . . . 44
CONTENTS
CHAPTER 1. SERVICE (SRV) MODE
The SRV key is used for operating in the SRV mode.
1. SRV. reset (Program Loop Reset)
Used to return the machine back to its operational state after a lock-up has occurred.
Procedure• Method 1
1) Turn off the AC switch.
2) Set the mode switch to (SRV′) position.
3) Turn on the AC switch.
4) Turn to (SRV) position from (SRV′) position.
• Method 2
1) Set the mode switch to PGM2 position.
2) Turn off the AC switch.
3) While holding down JOURNAL FEED key and RECEIPT FEEDkey, turn on the AC switch.
Note: When disassembling and reassembling always power up us-ing method 1 only. Method 2 will not reset the CKDC8.
Note: SRV programming job#926-B must be set to "4" to allow PGMprogram loop reset.
PRG. RESET
2. Master reset (All memory clear)
There are two possible methods to perform a master reset.
• MRS-1Used to clear all memory contents and return machine back to itsinitial settings. return keyboard back to default. for default key-board layout.
Procedure
1) Turn off the AC switch.
2) Set the MODE switch to the (SRV′) position.
3) Turn on the AC switch.
4) While holding down JOURNAL FEED key, turn to (SRV) positionfrom (SRV′) position.
• MRS-2Used to clear all memory and keyboard contents.This reset returns all programming back to defaults. The keyboardmust be entered by hand.This reset is used if an application needs different keyboard layoutother than that supplied by a normal MRS-1.
Procedure
1) Turn off the AC switch.
2) Set the MODE switch to the (SRV′) position.
3) Turn on the AC switch.
4) While holding down JOURNAL FEED key and RECEIPT FEEDkey, turn to (SRV) position from (SRV′) position.
5) Key position assignment:
After the execution of MRS-2, only the RECEIPT FEED andJOURNAL FEED keys can remain effective on key assignment.Any key can be assigned on any key position on the main key-board.
[key setup procedure]
MASTER PRESET
NOTES:
1: When the 0 key is pressed, the key of the key number ondisplay is disabled.
2: Push the key on the position to be assigned. With this, the keyof the key number on display is assigned to that key position.
Key number Key name Key number Key name
1 Numeric key "0" 10 Numeric key "9"
2 Numeric key "1" 11 Numeric key "00"
3 Numeric key "2" 12 Numeric key "000"
4 Numeric key "3" 13 Decimal point key
5 Numeric key "4" 14 CL key
6 Numeric key "5" 15 @/FOR key
7 Numeric key "6" 16 SBTL key
8 Numeric key "7" 17 CA/AT key
9 Numeric key "8"
3. Reading of the SRV mode program
List of program reports
JOB# Report name
900SRV-mode program full item report (not incl. keyboardlayout)
950Keyboard layout report (on keys other than dept. keysand direct PLU keys)
951Keyboard layout report (on dept. keys and direct PLUkeys)
970 SRV memory File allocation report
MRS-2 executed Key position set Free key
Disable
Free key setupcomplete.
*2
*1
0
0
[JOB# 900]All parameters contained for the SRV mode as listed
Key operation.
900 → @/FOR → CA/AT
Header graphical logo(Default:Graphical LOGOonly)
Date/TimeMachine No./Consective No.
JOB#
JOB#//Programmingdata(ABCD)
General Z1 reset counter
General Z2 reset counterDaily net Z2 reset counter
GT2 counter
GT3 counter
Secret code for PGM2 mode
Initial text mode programming
Hourly Z1 reset counterPLU Z1/Z2 reset counterCashier Z1/Z2 reset counterPBLU Z1 reset counter
Training GT counter
[JOB# 950]The Key layout report is printed in SRV mode
Key operation
950 → @/FOR → CA/AT
Header graphical logo(Default:Graphical LOGOonly)
Date/TimeMachine No./Consective No.
JOB#
Key No./Key label name/Location No.
Key No./Key label name/Location No.(---:Not used)
Key operation
951 → @/FOR → CA/AT
Header graphical logo(Default:Graphical LOGOonly)
Date/TimeMachine No./Consective No.
JOB#
Key No./Key label name/Location No.
Key No./Key label name/Location No.(---:Not used)
[JOB#970]Reading the contents of memory File Allocation
Key operation
970 → @/FOR → CA/AT
[JOB#990]Reading the Contents of the SRV-Mode Programming for SSP
Key operation
990 → @/FOR → CA/AT
Note: The SRV mode programming printout lists the actual memory files.For reference to memory file groups, please refer to SRV JOB#971 on page 14.
Header graphical logo(Default:Graphical LOGOonly)
Date/Time
Machine No./Consective No.
JOB#
File table No./No.of records/No.of used records
File table No./No.of records/No.of blocks/No.of used records
File memory start addressEmpty memory start addressMemory end address
Header graphical logo(Default:Graphical LOGOonly)
Date/TimeMachine No./Consective No.
JOB#
SSP No.Step No./SSP data
Error message
4. Service mode programming
The following is the key sequence required for programming.
Details of [A][B][C][D] will be discussed at each item description.
mark is MRS setting.
[JOB #901]:MRS=0002 [For "U" version]#901-A, B: Not used (Fixed at "00")
#901-C: 1. Rounding system
1. Rounding system 901-C
Normal 0
SINGAPORE 8
#901-D: 1. TAB setting
1. TAB setting 901-D
0 0
0.0 1
0.00 2
0.000 3
[JOB #901]: MRS=0002 [For "A" version]#901-A: Not used (Fixed at "0")
#901-B: 1. Tax system
1. Tax system 901-B
Auto tax 1-4 & manual tax 0
CANADIAN TAX 6
#901-C: 1. Rounding system
1. Rounding system 901-C
Normal 0
SINGAPORE 8
#901-D: 1. TAB setting
1. TAB setting 901-D
0 0
0.0 1
0.00 2
0.000 3
[JOB#902] NOT USED MRS=0000
[JOB#903] MRS=4000#903-A: 1. ECR data copy baud rate
1. Baud rate (bps) 903-A
2400 2
4800 3
9600 4
19200 5
38400 6
The communication speed with the ER-02FD is 19200bps max.
#903-B, C: Not used (Fixed at "00")
#903-D: 1. Type of food stamp system
1. Type of food stamp system 903-DNo food stamp 0
Tax not payable in food stamps 1
Tax payable in food stamps 2
Food stamp tax forgiveness 3
[JOB#904] MRS=0000
#904-A: 1. Printing of date
1. Printing of date 904-AYes 0
No 4
#904-B: 1. Printing of consecutive No.
1. Printing of consecutive No. 904-BYes 0
No 4
#904-C, D: Not used (Fixed at "00")
[JOB#905] MRS=0005 [For "U" version]#905-A: 1. Taxable 4 subtotal print on X/Z report.
2. Gross Tax 4 and refund Tax 4 total print on X/Z report.
3. Net Tax 4 total print on X/Z report.
1. Taxable 4SBTL
2. Gross Tax 4and refundTax 4
3. Net Tax 4905-A
PrintPrint
Print 0
Skip 1
SkipPrint 2
Skip 3
SkipPrint
Print 4
Skip 5
SkipPrint 6
Skip 7
#905-B: 1. Tax printing when taxable subtotal is zero.
2. Tax printing when tax is zero.
1. Taxable subtotal iszero
2. Tax is zero905-B
SkipPrint 0
Skip 1
PrintPrint 4
Skip 5
#905-C, D: Not used (Fixed at "05")
XXX CA/AT
(Job#)
[A] [B] [C] [D]
Numeric entry4 digits max
0
@/FOR
[JOB#905] MRS=0005 [For "A" version]#905-A: 1. Taxable 4 subtotal print on X/Z report.
2. Gross Tax 4 and refund Tax 4 total print on X/Z report.
3. Net Tax 4 total print on X/Z report.
1. Taxable 4SBTL
2. Gross Tax 4and refundTax 4
3. Net Tax 4905-A
PrintPrint
Print 0
Skip 1
SkipPrint 2
Skip 3
SkipPrint
Print 4
Skip 5
SkipPrint 6
Skip 7
#905-B: 1. Tax printing when taxable subtotal is zero.2. Tax printing when GST is VAT.3. Tax printing when tax is zero.
1. Taxablesubtotal is zero
2. GST isVAT
2. Tax is zero905-B
SkipPrint
Print 0
Skip 1
SkipPrint 2
Skip 3
PrintPrint
Print 4
Skip 5
SkipPrint 6
Skip 7
#905-C: 1. GST EXPT print on X/Z report
1. GST EXPT 905-C
Print 0
Skip 4
#905-D: 1. TAX METHOD
Tax4method (GST)
Tax3 method Tax2, 1method (PST)
905-DGST PST
Type VAT VAT
Tax on Tax 0
Type Tax on Base 1
Type VAT
Tax on Tax 2
Type Tax on Base 3
Type Add on Tax
Tax on Tax 4
Type Tax on Base 5
Type Add on Tax VAT
Tax on Tax 6
Type Tax on Base 7
Type Add on Tax
Addon Tax
Tax on Tax 8
Type Tax on Base 9
[JOB#906] MRS=0021#906-A: 1. Print Dept. and PLU number on receipt.
1. Print Dept. and PLU number on receipt. 906-A
No 0
Yes 4
#906-B: 1. Bottle return function
2. Hash department setting
1. Bottle return function 2. Hash departmentsetting
906-B
DisableDisable 0
Enable 2
EnableDisable 4
Enable 6
#906-C: 1. Split pricing counting
2. Multiplication entry
1. Split pricing counting 2. Multiplication entry 906-C
Quantity
Multiplication 0
Successivemultiplication
1
Split pricing 2
Package
Multiplication 4
Successivemultiplication
5
Split pricing 6
#906-D: 1. UPC (EAN) price look up at refund entry
2. Presetting consecutive No.
3. Fractional quantity
1. UPC (EAN)price lookup at refundentry
2. PresettingconsecutiveNo.
3. Fractionalquantity
906-D
Yes
YesNo 0
Yes1
NoNo 2
Yes3
No
YesNo 4
Yes5
NoNo 6
Yes7
[JOB#907] MRS=0010#907-A : Not used (Fixed at "0")
#907-B: 1. UPC code printing on journal
2. UPC code printing on receipt
1. UPC code printing onjournal
2. UPC code printing onreceipt
907-B
YesYes 0
No 1
NoYes 2
No 3
#907-C: 1. Minus Dept./PLU/UPC
1. Minus Dept./PLU/UPC 907-C
Disable 0
Enable 1
#907-D: Not used (Fixed at "0")
[JOB#908] MRS=0740#908-A: GT print on Z report
GT1 (NET) GT2 (+) GT3 (–) 908-A
PrintPrint
Print 0
Skip 1
SkipPrint 2
Skip 3
SkipPrint
Print 4
Skip 5
SkipPrint 6
Skip 7
#908-B: GT print on X report
GT1 (NET) GT2 (+) GT3 (–) 908-B
SkipSkip
Skip 0
Print 1
PrintSkip 2
Print 3
PrintSkip
Skip 4
Print 5
PrintSkip 6
Print 7
#908-C: 1. Add void-mode transaction data to hourly total report
2. X1/Z1 report in X2/Z2 mode
3. Resetting of consecutive number in Z1 resetting
1. Addvoid-modetransactionto hourlytotal report
2. X1/Z1 reportin X2/Z2mode
3. Resetting ofconsecutiveNo. in Z1resetting
908-C
NoEnable
No 0
Yes 1
DisableNo 2
Yes 3
YesEnable
No 4
Yes 5
DisableNo 6
Yes 7
#908-D: 1. Printing X/Z report Journal only/Receipt & Journal (Ex-cept the individual cashier report)
2. Z1 resetting, resets GT Enable/Disable
1. Printing X/Z report 2. GT resetting at Z1 908-D
Receipt & JournalDisable 0
Enable 1
JournalDisable 4
Enable 5
[JOB#909] MRS=2000#909-A: 1. Printing of training GT on the X report
2. Printing of training GT on the Z report
1. Printing of trainingGT on the X report
2. Printing of trainingGT on the Z report
909-A
SkipPrint 0
Skip 1
PrintPrint 2
Skip 3
#909-B: 1. Printing of data on PLU resetting report
2. Printing of data on UPC resetting report
1. Printing of data on PLUresetting report
2. Printing of data onUPC resetting report
909-B
YesYes 0
No 1
NoYes 4
No 5
#909-C: 1. Printing of data in void-mode totalizer and manager voidtotalizer on Z2 report
2. Printing of data in void-mode totalizer and manager voidtotalizer on Z1 report
1. Void-mode totalizeron Z2 printing
2. Void-mode totalizeron Z1 printing
909-C
PrintPrint 0
Skip 2
SkipPrint 4
Skip 6
#909-D: Not used (Fixed at "0")
[JOB#910] MRS=0204#910-A: Not used (Fixed at "0")
#910-B: 1. Cashier code display.
2. Auto cashier sign off at the end of transaction
1. Cashier code display. 2. Auto cashier sign offat the end oftransaction
910-B
HiddenNo
(After cashier Z1 only)0
Yes (Everytime) 1
AppearNo
(After cashier Z1 only)2
Yes (Everytime) 3
#910-C, D: Not used (Fixed at "4")
[JOB#911] MRS=0000#911-A: 1. Fraction treatment
1. Fraction treatment 911-ARound off 0
Round up 1Round down 2
#911-B: 1. C/D check of UPC
2. C/D checking at the time of PBLU code entry
1. C/D check of UPC2. C/D checking at the
time of PBLU code entry911-B
NoNo 0
Yes 2
YesNo 4Yes 6
#911-C, D: Not used (Fixed at "00")
[JOB#912] MRS=0060#912-A: 1. Date print format
Date format 912-AMonth/Day/Year 0
Day/Month/Year 1Year/Month/Day 2
#912-B: 1. Time system
1. Time system 912-B12H 0
24H 1
#912-C: 1. After transaction receipt format
2. Copy receipt
3. Footer print control
1. Aftertransactionreceipt
2. Copyreceipt
3. Footer printcontrol 912-C
Total only
No
All receipt 0On selected functionkeys at the time offinalization
1
Yes
All receipt 2On selected functionkeys at the time offinalization
3
Detail
No
All receipt 4On selected functionkeys at the time offinalization
5
Yes
All receipt 6On selected functionkeys at the time offinalization
7
#912-D: 1. LOGO Message control.
1. LOGO Message control 912-D3-line header instead of a LOGO 0Graphical LOGO only 1
Graphical LOGO and 3-line footer 26-line header 3Graphical LOGO and 3-line header 43-line header and 3-line footer 5
[JOB#913] MRS = 0104#913-A: 1. Content of TOTAL VP amount
1. Content of TOTAL VP amount 913-ATotal amount 0
Tendered amount 1
#913-B: 1. Printing of SBTL
2. Printing of MDSE SBTL upon key depression
3. Escape the compulsion of VP or SLIP
NOTE: Must turn to MGR mode and depress
• , PRINT keys to escape validation
1. SBTL Print 2. MDSESBTL print
3. Escape thecompulsoryof VP
913-B
NoNo
Disable 0
Enable 1
YesDisable 2
Enable 3
YesNo
Disable 4
Enable 5
YesDisable 6
Enable 7
#913-C: 1. Buzzer off 2 sec. after lock error.
2. Buffered keyboard
1. Error beep 2. Buffered keyboard 913-C
2-sec. offYes 0
No 1
ConstantYes 2
No 3
#913-D: 1. Drawer closing operation
2. Error mode
3. Key catch sound
1. Drawer closedcompulsory
2. Error mode 3. Key catchsound
913-D
Non-compulsoryAll lock error
Enable 0
Disable 1
Miss operation(One shot error)
Enable 2
Disable 3
CompulsoryAll lock error
Enable 4
Disable 5
Miss operation(One shot error)
Enable 6
Disable 7
[JOB#914] MRS = 3100#914-A: 1. Receipt issuing at no-sale
2. [NS] key separation from [CA/AT] key for no sale func-tion is separate
3. Tax delete operation
1. Receipt issuingat no-sale
2. [NS] keyseparation
3. Tax delete914-A
EnableYes
Inhibit 0
Enable 1
NoInhibit 2
Enable 3
DisableYes
Inhibit 4
Enable 5
NoInhibit 6
Enable 7
Header
Footer
Type : 0
5
32
LOGO
1
4
LOGO
LOGO
#914-B: 1. No-sale after NON ADD code entry
1. No-sale after # entry 914-B
Disable 0
Enable 1
#914-C: 1. Action to be taken when the machine is locked by thereceipt/journal paper near end check
2. VOID mode
3. Non-add code entry at the beginning of a transactionoperation
1. Action to betaken whenthe machineis locked bythe journalpaper nearend check
2. VOID mode 3. Non-addcode entry atthe beginningof atransactionoperation
914-C
Unlocked by CLkey
EnableNon-compulsory 0
Compulsory 1
DisableNon-compulsory 2
Compulsory 3
Enforce ofpaper roll
replacement
EnableNon-compulsory 4
Compulsory 5
DisableNon-compulsory 6
Compulsory 7
#914-D: 1. Manual tax
2. CHECK CASHING
3. Non-add code entry
1. Manual tax 2. CHECKCASHING
3. Non-addcode entry
914-D
EnableDisable
Enable 0
Disable 1
EnableEnable 2
Disable 3
DisableDisable
Enable 4
Disable 5
EnableEnable 6
Disable 7
[JOB#915] MRS = 0000#915-A: 1. Amount symbol
1. Amount symbol 915-A" $ " 0
" " 1" " 2
#915-B: Not used (Fixed at "0")
#915-C: 1. Paper near end check
2. ST%, ST(–) as many times needed/operation only once
1. Paper near end check 2. ST%, ST(–) as manytimesneeded/operationonly once
915-C
YesUnlimited 0
Once only 2
NoUnlimited 4Once only 6
#915-D: Not used (Fixed at "0")
[JOB#916] MRS = 1400#916-A: 1. Print format when text and amount overlaps each other
REG mode
1. Print format when text and amountoverlaps each other REG mode
916-A
Truncate text 0
2 line print 1
#916-B: 1. Finalization by charge when SBTL 0
2. Food stamp subtotal entry before food stamp tender
1. Finalization bycharge whenSBTL 0
2. Food stamp subtotalentry before food stamptender
916-B
RF type of sale onlyNon-compulsory 0
Compulsory 1
AllowedNon-compulsory 4
Compulsory 5
#916-C: 1. Negative merchandise subtotal
2. Subtotal entry compulsory before tendering
3. Subtotal entry before direct non-tendering finalization
1. Negativemerchan-disesubtotal
2. Subtotal entrycompulsorybeforetendering
3 .Subtotal entrybefore directnon-tenderingfinalization
916-C
AllowNoncompulsory
Non-compulsory 0
Compulsory 1
CompulsoryNon-compulsory 2
Compulsory 3
DisallowNon-compulsory
Non-compulsory 4
Compulsory 5
CompulsoryNon-compulsory 6
Compulsory 7
#916-D: 1. Coupon PLU printing on X/Z report
2. Net sales subtotal (NET1) printing on X/Z report
3. CHECK change total printing on X/Z report
1. Print couponPLU’s onGeneral report
2. Print net salesSBTL (NET1)on Generalreport
3. Print CHKCHANGE onGeneral report
916-D
PrintPrint
Print 0
Skip 1
SkipPrint 2
Skip 3
SkipPrint
Print 4
Skip 5
SkipPrint 6
Skip 7
[JOB#917] MRS = 0000#917-A: 1. Printing of Taxable 1 subtotal on X/Z report
2. Printing of Gross Tax 1 and refund Tax 1 total on X/Zreport
3. Printing of Net Tax 1 total on X/Z report
1. Taxable 1subtotal onX/Z report
2. Gross Tax 1and refundTax 1 totalon X/Z report
3. Net Tax 1total on X/Zreport
917-A
PrintPrint
Print 0
Skip 1
SkipPrint 2
Skip 3
SkipPrint
Print 4
Skip 5
SkipPrint 6
Skip 7
#917-B: 1. Printing of Taxable 2 subtotal on X/Z report
2. Printing of Gross Tax 2 and refund Tax 2 total on X/Zreport
3. Printing of Net Tax 2 total on X/Z report
1. Taxable 2subtotal onX/Z report
2. Gross Tax 2and refundTax 2 totalon X/Z report
3. Net Tax 2total on X/Zreport
917-B
PrintPrint
Print 0
Skip 1
SkipPrint 2
Skip 3
SkipPrint
Print 4
Skip 5
SkipPrint 6
Skip 7
#917-C: 1. Printing of Taxable 3 subtotal on X/Z report
2. Printing of Gross Tax 3 and refund Tax 3 total on X/Zreport
3. Printing of Net Tax 3 total on X/Z report
1. Taxable 3subtotal onX/Z report
2. Gross Tax 3and refundTax 3 totalon X/Z report
3. Net Tax 3total on X/Zreport
917-C
PrintPrint
Print 0
Skip 1
SkipPrint 2
Skip 3
SkipPrint
Print 4
Skip 5
SkipPrint 6
Skip 7
#917-D: 1. Printing of Total Tax amount on X/Z report
2. Printing of Gross manual Tax and refund manual Taxon X/Z
3. Printing of Net manual Tax total on X/Z report
1. Total TaxAmount
2. Grossmanual Taxand Refundmanual Taxon X/Z report
3. Net manualTax total onX/Z report 917-D
PrintPrint
Print 0
Skip 1
SkipPrint 2
Skip 3
SkipPrint
Print 4
Skip 5
SkipPrint 6
Skip 7
[JOB#918] MRS = 2000#918-A: 1. Direct non-tendering finalization after previous tender
entry
1. Direct non-tendering finalization afterprevious tender entry
918-A
Disable 0
Enable 2
#918-B: 1. Fractional entries for non-scalable UPC/PLU/DEPT.
1. Fractional entries for non-scalableUPC/PLU/DEPT.
918-B
Enable 0
Disable 1
#918-C, D: Not used (Fixed at "00")
[JOB#919] MRS = 0400#919-A: Not used (Fixed at "0")
#919-B: 1. Checking of cashier# on guest check
2. PBLU code
1. Checking of cashier#on guest check
2. PBLU code919-B
YesAuto generation 0
Manual 1
NoAuto generation 4
Manual 5
#919-C: 1. PB entry
2. Amount printing when PLU unit price is 0.
1. PB entry 2. Amount printingwhen PLU unit price is0.
919-C
NoncompulsoryNo 0
Yes 1
CompulsoryNo 2
Yes 3
919-D: 1. Conversion SBTL printing of native SBTL
2. Foreign currency format
1. Conversion SBTLprint of native SBTL
2. Foreign currency919-D
YesNot 0
Omit digits lower thanTAB position
1
NoNot 4
Omit digits lower thanTAB position
5
[JOB#920] NOT USED MRS = 0000
[JOB#921] NOT USED MRS = 0000
[JOB#922] NOT USED MRS = 0000
[JOB#923] NOT USED MRS = 0000
[JOB#924] NOT USED MRS = 0000
[JOB#925] NOT USED MRS = 0000
[JOB#926] MRS = 0400#926-A: Not used (Fixed at "0")
#926-B: 1. Program reset in PGM 2 mode
1. Program reset at PGM2 mode 926-B
Disable 0
Enable 4
#926-C: 1. Open store/Close store with on-line
2. Send AT command string with JOB#500 (Open store)
3. Send AT command string with JOB#501 (Close store)
1. Openstore/Closestore foron-line
2. Send ATcommandstring withJOB#500(Open store)
3. Send ATcommandstring withJOB#501(Close store)
926-C
NoNo
No 0
Yes 1
YesNo 2
Yes 3
YesNo
No 4
Yes 5
YesNo 6
Yes 7
#926-D: 1. Connect on-line channel in close store
1. Allow connection of the on-linechannel in close store
926-D
No 0
Yes 4
[JOB#927] NOT USED: MRS = 0000
[JOB#928] MRS = 0000#928-A: 1. Printing of slip logo text
1.Printing of slip logo text 928-A
No 0
Yes 1
#928-B: 1. VP message printing on slip
2. Header line on slip paper when a reorder is madeprinted
1. VP message printingon slip
2. Header line on slippaper when a reorderis made printed
928-B
Check onlyPrinted 0
Not 1
Check & ChargePrinted 2
Not 3
#928-C:
1.Printing of PLU on bill when it is 0
1.Printing of PLU on bill when it is 0 928-C
Yes 0
no 4
#928-D 1. Printing of PB/SERVICE ON SLIP
2. Compulsory bill print system(The bill printing at serv and final in GLU system acts oneach media’s preset)
1. Printing ofPB/SERVICE ON SLIP
2. Compulsory bill printsystem
928-D
Yes
According to eachmedia’s preset
0
Compulsory for everyentry
1
Compulsory for PB 2
No
According to eachmedia’s preset
4
Compulsory for everyentry
5
Compulsory for PB 6
[JOB#929] MRS = 0000#929-A, B, C: Not used (Fixed at "000")
#929-D: 1. Taxable status of PLU/UPC which has not beens inPGM
1. Taxable status of PLU / UPC which isset at "Non-taxable" by PGM
929-D
According to its associated Department 0
Non-taxable 2
[JOB#930 ∼941] MRS = 0000RESET REPORT COUNTER
JOB # Function
930 Z1 report counter
933 Hourly Z1 report counter
934 PLU Z1/Z2 report counter
935 Cashier Z1/Z2 report counter
936 PBLU report counter
937 Z2 report counter
939 31 day daily net Z2 report counter
ABCD
"0000"
Job# @/FOR CA/AT
Initial value of Z counter
[JOB#942, 943, 969] MRS = 0000000000000GT COUNTER PRESETTING
JOB # Function942 GT2 (Positive GT)943 GT3 (Negative GT)969 TRAINING GT
Note: GT1 is obtained by calculationEquation: GT1=GT2-GT3
[JOB#944] MRS = 0000PGM2 secret code presetting
NOTE: When the secret code "0" is programmed, the secret codeentry is be inhibited.
[JOB#950] MRS = STANDARD KEY LAYOUTFree key layout (Except for department keys and direct PLU keys.)
XXX : 1 to 88: 999 (For inhibiting key)
[JOB#951] MRS = STANDARD KEY LAYOUTFree key layout (department keys and direct PLU keys)
XXX : 1 to 68: 999 (For Inhibiting key)
• Programming of the keys to be dept keys or direct PLU keys onthe keyboard.
• Key No. is assigned to each key which is supposed to be dept.Key or direct PLU key by depressing the key after entering the keyNo.
• Those keys programmed by this job No. will be dept. keys if dept.code is assigned, and will be direct PLU keys if PLU code isassigned in the PGM2 mode.
FUNCTION KEY LIST
Key No. KEY KEY TEXT 1 0 KEY 0 KEY 2 1 KEY 1 KEY 3 2 KEY 2 KEY 4 3 KEY 3 KEY 5 4 KEY 4 KEY 6 5 KEY 5 KEY 7 6 KEY 6 KEY 8 7 KEY 7 KEY 9 8 KEY 8 KEY10 9 KEY 9 KEY11 00 KEY 00 KEY12 000 KEY 000KEY13 DECIMAL POINT . KEY14 CLEAR CL15 @/FOR @/FOR16 SUB TOTAL SBTL17 CA/AT CA/AT18 MDSE SBTL MDS ST19 # #20 NO SALE NS21 PLU/SUB PLU/SB22 REFUND SALES RF SAL23 TAX1 SHIFT TAX1SF24 TAX2 SHIFT TAX2SF25 TAX3 SHIFT TAX3SF26 TAX4 SHIFT TAX4SF27 FS SHIFT FS SHT28 PRINT PRINT29 RCPT RCPT30 VOID VOID31 REFUND RFND32 %1 %133 %2 %234 %3 %335 %4 %436 (–)1 (–)137 (–)2 (–)238 (–)3 (–)339 (–)4 (–)440 TAX TAX41 AUTO AUTO42 AUTO2 AUTO243 AUTO3 AUTO344 AUTO4 AUTO445 AUTO5 AUTO546 AUTO6 AUTO647 AUTO7 AUTO748 AUTO8 AUTO849 AUTO9 AUTO950 AUTO10 AUTO1051 CASH2 CA252 CHECK CHK53 CHECK2 CHK254 CH1 CH155 CH2 CH256 CH3 CH357 CH4 CH458 CH5 CH559 CONV1 CONV160 CONV2 CONV2
0
000000000000013 digits
Job# CA/AT@/FOR
CA/AT944 XXXX4 digits
@/FOR
0
Free key@/FOR CA/AT
@/FOR
Key number automaticincrement
Key number manualincrement
Initial setting
XXXKey No.
To inhibitSBTL
increment key No.
950
Free key@/FOR CA/AT
@/FORKey No.
Key number automaticincrement
Key number manual increment
To inhibitSBTL
increment key No.
951 XXX
Key No. KEY KEY TEXT61 CONV3 CONV362 CONV4 CONV463 FS TEND FSTEND64 RA RA65 RA2 RA266 PO PO67 PO2 PO268 CASHIER NO. CASH#69 BIRTHDAY BIRTH70 UPC UPC71 AMT AMT72 DEPT# DEPT#73 REPEAT REPEAT74 INQUIRE INQ75 NO DELETE NO DEL76 PRICE CHANGE PRCHNG77 PRICE 1 P178 PRICE 2 P279 PRICE 3 P380 SLIP SLIP81 PBLU PBAL82 N.C. N.C.83 SERVICE SRVC84 FINAL FINAL85 DEPOSIT DEPO86 DEPOSIT RFND DEP.RF87 SCALE SCALE88 OPEN TARE OPN TR
999 INHIBIT
ER-A450T KEY POSITION
[JOB#971]Memory file group PROGRAMMING. (File creation deletion andchange of record count or block count)
Key operation
• Normal file
GroupNo.
File name Type* File table No.(Create/Erase)
1 Dept. 1 1,2,3,52 Dept. Text(12) 0 33 Dept. Text(16) 0 44 PLU 1 7,8,9,115 PLU Text(12) 0 96 PLU Text(16) 0 107 Link PLU 1 138 UPC 1 14,15,16,189 UPC Price1 0 16,2010 UPC Price1-3 0 17,2211 UPC Text(12) 0 1812 UPC Text(16) 0 1913 UPC Daily sales 0 20 (or 22)14 UPC Mix&Match 1 26,2715 UPC Link 1 2816 Cashier 1 32,33,34,35,3617 Hourly 0 40,4118 Daily Net 0 42,4319 Reg. Buffer 1 4420 PBLU 1 4521 Term Department 0 622 Term PLU 0 1223 Term UPC 0 21 (or 23)24 Term Transaction 0 3125 Term Cashier transaction 0 37
26All of Term files.
06,12,21 (or23),31,37
27 UPC PGM Pick up 1 2428 UPC X/Z Pick up 1 25
Type = 0 ; Create/Erase only
Type = 1 ; Create/Erase and Increase/decrease the number ofRecords or blocks.
* : The files which are created or erased by the entry of group No.
04 08 12 16 20 24 28 32 36 42 48 54 60 66
03 07 11 15 19 23 27 31 35 41 47 53 59 65
02 06 10 14 18 22 26 30 34 40 46 52 58 64
01 05 09 13 17 21 25 29 34 39 45 51 57 63
43 49 55 61 67
44 50 56 62 68
37
38
R J
:FIXED KEY (NO TO CHANGE)
971 XXXXXabc CA/AT@/FOR@/FOR
File group No. Number of records
File table
TableNo.
File nameRECORD BLOCK Label
sizeDatasizeMRS Max. #1 MRS Max. #2
1 Dept. Preset 20 50 1 1 1 7
2 Price 20 50 (1) 1 1 0 3
3 Text (12 chara.) 20 50 (1) 1 1 0 12
4 Text (16 chara.) 0 50 (1) 0 1 0 16
5 Daily 20 50 (1) 1 1 0 9
6 Term 20 50 (1) 1 1 0 9
7 PLU Preset 500 *** 1 1 5 7
8 Price 500 *** (7) 1 1 0 3
9 Text (12 chara.) 500 *** (7) 1 1 0 12
10 Text (16 chara.) 0 *** (7) 0 1 0 16
11 Daily 500 *** (7) 1 1 0 9
12 Term 0 *** (7) 0 1 0 9
13 Link PLU 0 *** 0 1 3 15
14 UPC Preset 1500 *** 1 1 9 6
15 Flag 1500 *** (14) 1 1 0 2
16 Price 1 1500 *** (14) 1 1 0 3
17 Price 1-3 0 *** (14) 0 1 0 9
18 Text (12 chara.) 1500 *** (14) 1 1 0 12
19 Text (16 chara.) 0 *** (14) 0 1 0 16
20 Daily (Price 1) 1500 *** (14) 1 1 0 9
21 Term (Price 1) 0 *** (14) 0 1 0 9
22 Daily (Price 1-3) 0 *** (14) 0 1 0 9
23 Term (Price 1-3) 0 *** (14) 0 3 0 9
24 UPC PGM Pick up 100 *** 1 3 9 0
25 UPC X/Z Pick up 100 *** 1 1 9 0
26 Mix & Match Table 0 *** 0 1 1 5
27 Sales buffer 0 *** (26) 0 1 0 5
28 UPC link 0 *** 0 1 7 15
29 Transaction Label 89 89 1 1 2 0
30 Daily 89 89 (29) 1 1 0 8
31 Term 89 89 (29) 1 1 0 8
32 Cashier Preset 4 99 4 99 (32) 1 3
33 Flag 4 99 (32) 4 99 (32) 0 2
34 Text 4 99 (32) 4 99 (32) 0 8
35 Cashier transaction Label 43 43 1 1 2 0
36 Daily 43 43 (35) 1 1 0 8
37 Term 43 43 (35) 1 1 0 8
38 Total cashier buffer Label 43 43 1 1 2 0
39 Total 43 43 (38) 1 1 0 8
40 Hourly Label 48 48 1 1 1 0
41 Daily 48 48 (40) 1 1 0 8
42 Daily net Label 36 36 1 1 3 0
43 Total 36 36 (42) 1 1 0 8
44 Reg. buffer 80 255 1 1 0 50
45 PBLU (Label + Data) 10 *** 1 1 2 125
(#1) : Same as the number of record of table No. N
(#2) : Same as the number of block of table No. N
[JOB#996, 998] RAM DATA BACKUP function(ECR ECR, ECR ER-02FD)
[JOB#996] RAM data send
X : SSP = 0
Standard RAM (128KB) = 1Optional RAM: ER-03RA (512KB) = 2
Only nacessarywhen the ER-01FDor ER-02FD is beingused.
[JOB#998] RAM data receive
[JOB#987] MRS = 0MRS = 0
Text Changing (To Default text)
X: 0 = English text
2 = French text
When this job is executed, below texts are set as default data.
(a) Function text
(b) Cashier text
(c) Each message text (LOGO, etc..)
5. PC software utility
(1) OutlineThis Specification document describes the "02FD.EXE" PC utility.
The "02FD.EXE" works with the Windows95/98 operating systemsand has the following functions by connecting ER-A450T via RS232.
02FD.EXE : All RAM Data Upload/Download
(2) Environment
PC and ER-A450T are connected by RS232.
Connect the PORT2(CH1) of the ER-A450T to the RS-232 interfaceof the PC.
RS232 Cable pin out :
996 X@/FOR
All data
CA/AT
SBTL
Send to ECR or ER-02FD(Baud rate setting:#903-A)Send to ECR(Auto baud rate setting)
998 @/FOR CA/AT
SBTL
Receive from ECR or ER-02FD(Baud rate setting:#903-A)Receive from ECR(Auto baud rate setting)
987 X
0
@/FOR CA/AT
PC
RS232 cable
ER-A450T
Channel No.Port1(CH8)
Channel No.Port2(CH1)
SD 3
RD 2
RTS 7
DCD 1
DTR 4
DSR 6
CTS 8
SG 5
3
2
7
1
4
6
8
5
SD
RD
RTS
DCD
DTR
DSR
CTS
SG
[ER-A450T] [PC]
No Procedure on P.C. side No Procedure on ER-A450T side
1Install "02FD.EXE" on the P.C.ALL RAM Data UpLoad : Go to "2"ALL RAM Data DownLoad : Go to "9"
2 ALL RAM Data UpLoad ( ER-A450T -> PC ) 2 Place the SRV key in the SRV mode.
3
"Execute "02FD.EXE" on P.C"*Don’ t execute the other Software at the same time.
4
Set the Communication method by "Setting" Button."
Push "OK" Button.
5Push "POS -> PC" Button.And Select the Receiving File.
6
Entry of JOB#996 in the SRV mode
ER-A450T shows
7
Communication starts.
8UpLoad is completed.The initial Window is shown."Push "Exit" Button."
8UpLoad is completed.
9 ALL RAM Data Download ( PC -> ER-A450T ) 9 Place the SRV key in the SRV mode.
996 CA/AT@/FOR
00000
No Procedure on P.C. side No Procedure on ER-A450T side
10
Execute "02FD.EXE" on P.C*Don’ t execute the other Software at the same time.
11
Set the Communication method by "Setting" Button.
12
Entry of JOB#998 in the SRV mode
ER-A450T shows
Push "OK" Button.
13Push "PC -> POS" Button.And Select the Receiving File.
14
Communication starts.
15Download is completed.The initial Window is shown.Push "Exit" Button.
15Download is completed.
16 Execute "Service Reseth" on ER-A450T
998 CA/AT@/FOR
00000
CHAPTER 2. PROGRAM (PGM2/PGM1) MODE
1.Reading of the PGM mode program
[JOB#1000]: UPC reading
[JOB#2020]: UPC Mix & Match readingKey operation
[JOB#2025]: UPC/EAN format programming reading
[JOB#2030]: UPC LINK preset or reading
XXXXXXXXXXXXX
Pick up (to the number of records in Pick-up file)
UPC code
(Scanning) ;Previous pick-upped UPC codes
;All UPC data
1000 @/FOR CA/AT@/FOR
CA/AT@/FOR
CA/AT
JOB#/Mode title
Header graphical logo(Default:Graphical LOGOonly)
Date/TimeMachine No./Consective No.
Taxable/Price
Programming JOB#2010-A,B,C/Age limitation/Mix & Match table Mo.
Non-delete flag/Taxable/Sign/Price
UPC code/Type *1/ Associated DEPT./ Base q'ty*1 L : Link UPC type/ (space) : Normal UPC
2020 @/FOR CA/AT
Header graphical logo(Default:Graphical LOGOonly)
Date/TimeMachine No./Consective No.
JOB#/Mode title
Table No./Matching count/Adjust amount
2025 @/FOR CA/AT
Programming:JOB#2025
Programming:JOB#2029
Header graphical logo(Default:Graphical LOGOonly)
Date/TimeMachine No./Consective No.
JOB#/Mode title
2030 @/FOR CA/AT
Header graphical logo(Default:Graphical LOGOonly)
Date/TimeMachine No./Consective No.
JOB#/Mode title
Linked PLU code
[JOB#1100]: DEPT readingKey operation
[JOB#1200]: PLU readingKey operation
1100 XXStart No.
@/FOR CA/ATXXEnd No.
Single item
@/FOR
All
Header graphical logo(Default:Graphical LOGOonly)
Date/TimeMachine No./Consective No.
JOB#/Mode title
Range
DEPT. code/Taxable/PriceText/Group No.Programming:JOB#2110/Age limitation/HALO
1200 XXXXStart No.
@/FOR CA/ATEnd No.
Single item
@/FOR XXXX
All
Header graphical logo(Default:Graphical LOGOonly)
Date/TimeMachine No./Consective No.
JOB#/Mode title
Range
Taxable/Price
PLU code/Associated Dept.code/Type:L=Link PLU,(space)=Normal PLU/Base Q'ty
TextProgramming:JOB#2210/Age limitation
[JOB#2220]: LINK PLU PRESET READINGKey operation
[JOB#2119]: DIRECT KEY READINGKey operation
2220 @/FOR CA/AT
Header graphical logo(Default:Graphical LOGOonly)
Date/TimeMachine No./Consective No.
JOB#/Mode title
Range
PLU code/Linked PLU code(Max.5)
2119 @/FOR CA/AT
Header graphical logo(Default:Graphical LOGOonly)
Date/TimeMachine No./Consective No.
JOB#/Mode title
Key No./Dept.code(JOB#2119)
Key No./Inhibit
[JOB#1300]: FUNCTION PRESET READINGKey operation
1300 @/FOR CA/AT
JOB#/Mode title
Header graphical logo(Default:Graphical LOGOonly)
Date/TimeMachine No./Consective No.
Function No./Text
Type:S=Subtotal, I=Item/Sign/Amount
Function No./Text
HALO
Function No./Text/HALO
Function No./Text/HALO
[JOB#1500]: CASHIER READINGKey operation
[JOB#2600]: READING OF OTHERKey operation
1500 @/FOR CA/AT
JOB#/Mode title
Header graphical logo(Default:Graphical LOGOonly)
Date/TimeMachine No./Consective No.
Cashier No./Cashier codeName/Drawer No.
2600 @/FOR CA/AT
JOB#/Mode title
Header graphical logo(Default:Graphical LOGOonly)
Date/TimeMachine No./Consective No.
Programming:JOB#2617
Programming:JOB#2619
Programming:JOB#2620
Programming:JOB#2630Programming:JOB#2631Programming:JOB#2632
Programming:JOB#2690
Programming:JOB#2614
Programming:JOB#2615
Programming:JOB#2616
Programming:JOB#2618
[JOB#2640]: SLIP text program readingKey operation
[JOB#2700]: TAX TABLE READING REP.Key operation
[JOB#2800]: PBLU code program readingKey operation
[JOB#2900]: AUTO KEY READINGKey operation
2640 @/FOR CA/AT
JOB#/Mode title
Header graphical logo(Default:Graphical LOGOonly)
Date/TimeMachine No./Consective No.
Programming:JOB#2642
2700 @/FOR CA/AT
JOB#/Mode title
Header graphical logo(Default:Graphical LOGOonly)
Date/TimeMachine No./Consective No.
Tax No./RateLower tax limitation
2800 @/FOR CA/AT
JOB#/Mode title
Header graphical logo(Default:Graphical LOGOonly)
Date/TimeMachine No./Consective No.
PBLU Code range
2900 @/FOR CA/AT
JOB#/Mode title
Header graphical logo(Default:Graphical LOGOonly)
Date/TimeMachine No./Consective No.
Auto key No.
Programming:JOB#2900
Not programmed
[JOB#2990]: THERMAL PRINTER SETUP REPORT 2. Programming
[JOB#1000]PROGRAMMING UPC/EAN CODES DEPARTMENTS TO BE ASSO-CIATED WITH EANs
XXXXXXXXXXXXX: UPC code
YY: DEPT. code = 01 to 50
MRS = Nothing (Default = 01)
Default is a value which is set when new UPC record is created byanother programming JOB.
If the record of the entered UPC code is not in the UPC file at thisprogramming step, the UPC code will be created.
[JOB#1010]UPC UNIT PRICE PROGRAMMING
XXXXXXXXXXXXX: UPC code
YYYYYY: Amount = 0 to 999999
MRS = 000000
If the record of the entered UPC code is not in the UPC file at thisprogramming step, the UPC code will be created.
To use the Price 2,3, it needs the PRICE1-3 file that is created bySRV file JOB.
[JOB#1011]UPC BASE Q’TY PROGRAMMING
XXXXXXXXXXXXX: UPC code
ZZ : Base quantity = 00 to 99
MRS = 00
If the record of the entered UPC code is not in the UPC file at thisprogramming step, the UPC code will be created.
2990 @/FOR CA/AT
JOB#/Mode title
Header graphical logo(Default:Graphical LOGOonly)
Date/TimeMachine No./Consective No.
Printing sample
1000 YYXXXXXXXXXXXXX
No change
UPC code
(Scanning)
CA/ATSBTL
@/FOR @/FOR
YYYYYY1010 XXXXXXXXXXXXX
No change
UPC code
(Scanning)
CA/ATSBTL
@/FOR @/FOR
*Price 1~3
1011 ZZXXXXXXXXXXXXX
No change
UPC code
(Scanning)
CA/ATSBTL
@/FOR @/FOR
[JOB#2010]UPC FUNCTION PROGRAMMING
XXXXXXXXXXXXX: UPC code
A: Price shift entry A
Allowed 0
Inhibited 1
Compulsory 2
B: Tare table No. B
Non 0
Table No. 1 to 9
C: Scale entry C
Inhibit 0
Enable 1
Compulsory 2
D: Record delete method D
Delete at X/Z non-accessedUPC deleting job
0
Non delete 1
Delete now 4
MRS = Nothing (Default = 0000)
The default is a value is set when a new UPC record is created byanother programming JOB.
If the record of the entered UPC code is not in the UPC file at thisprogramming step, the UPC code will be created.
[JOB#2011]UPC TAX STATUS PROGRAMMING
XXXXXXXXXXXXX: UPC code
A: Sign A
+ 0
- 1
B: Food stamp B
No 0
Yes 1
C: Taxable 4 C
No 0
Yes 1
D: Taxable 3 D
No 0
Yes 1
E: Taxable 2 E
No 0
Yes 1
F: Taxable 1 F
No 0
Yes 1
MRS = 0000000
If the record of the entered UPC code is not in the UPC file at thisprogramming step, the UPC code will be created.
[JOB#2014]UPC TEXT PROGRAMMING
XXXXXXXXXXXXX: UPC code
Characters can be entered by using the character keys (directkey) or the numeric keys (code entry).Please refer to section 4.
MRS = 0000000
If the record of the entered UPC code is not in the UPC file at thisprogramming step, the UPC code will be created.
Note: The ER-A450T does not have "Readout of the programmedtext" because the text modification function is not supported.
[JOB#2017]UPC MIX & MATCH TABLE No. PROGRAMMING
XXXXXXXXXXXXX : UPC code
ZZ : Mix&Match table No. = 00 to 99
MRS = 00
If the record of the entered UPC code is not in the UPC file at thisprogramming step, the UPC code will be created.
2010 ABCDXXXXXXXXXXXXX
No change
UPC code
(Scanning)
CA/ATSBTL
@/FOR @/FOR
2011 ABCDEFXXXXXXXXXXXXX
No change
UPC code
(Scanning)
CA/ATSBTL
@/FOR @/FOR
Characterkey
All space
2014 XXXXXXXXXXXXXUPC code
(Scanning)
CA/ATSBTL
@/FOR @/FOR
2017 ZZXXXXXXXXXXXXX
No change
UPC code
(Scanning)
CA/ATSBTL
@/FOR @/FOR
[JOB#2020]MIX & MATCH TABLE PROGRAMMING
XX: Table No. = 01 to 99
ZZ: Matching count = 1 to 99
YYYYYY: Adjust amount = 1 to 999999
MRS = nothing
[JOB#2025]UPC/EAN CODE FORMAT PROGRAMMING
VV: System sign
A: Length of field 1
B: Length of field 2
C: Not used (Fixed at "0")
D: Meaning of field 2 D
Price 0
Quantity 2
E: Price check digit used E
No 0
Yes 1
F: TAB or Decimal point of field 2 F
0 0
0.0 1
0.00 2
0.000 3
MRS = (Below values are established)
Type VV A B C D E F
UPC8 2 2 4 0 0 0 2
UPC13 02 5 4 0 0 1 2
MRS format
<UPC LEAN CODE FORMAT>(Example)
UPC 13: VV WWWWW X YYYY Z
UPC 8: V WW YYYY Z
VVorV
WWWWW orWW
X YYYY Z
Systemsign
Field1Pricecheckdigit
Field2 Checkdigit
(Note)
ISBN/ISSN and press code always use the fixed format even if belownumbers are set as NON PLU code.
System sign = 37, 43, 78, 98, 97, 141
[JOB#2029]RECORD DELETE PERIOD PROGRAMMING
XX: Record delete period = 00 to 99 days(00= Record delete function is not available)
MRS = 99
[JOB#2030]UPC LINK (with PLU) PROGRAMMING
XXXXXXXXXXXXX: UPC code
YYYYYY: PLU code = 1 to 999999 max.
MRS = 0
When the "SBTL" key is pressed without entering any number asthe first PLU code (YYYYYY), the previous data is cleared.
The PLU code should already be defined when they are used inthis programming step.
[JOB#2080]UPC LOWER LIMITATION AGE PROGRAMMING
XXXXXXXXXXXXX : UPC code
YY : Age = 00 to 99 (00 = No limitation)
MRS = 00
If the record of the entered UPC code is not in the UPC file at thisprogramming step, the UPC code will be created.
2020 ZZYYYYYYXX
Delete
Table No.
CA/ATSBTL
@/FOR @/FOR
System sign
ABCDEF
Max. =11
2025 VV
Delete
CA/ATSBTL
@/FOR @/FOR
2
System signField 2
PLU or DEPT. code:2 digits
PRICE:5 digits (00.00)
Check digit
0 2
System sign Field 1
PLU code:5 digits
Field 2
PRICE:4 digits (000.00)
Price Check digit
Check digit
<UPC8>
<UPC13>
Field 1
2029 XX
0
CA/AT@/FOR
Max. 5 times
YYYYYY2030 XXXXXXXXXXXXX
No change
UPC code
(Scanning)
CA/ATSBTL
@/FOR @/FOR
2080 YYXXXXXXXXXXXXX
No change
UPC code
(Scanning)
CA/ATSBTL
@/FOR @/FOR
[JOB#1110]PROGRAMMING DEPT. PRICE
XX: DEPT-CODE = 01 - 50
YYYYYY: PRICE = 0 - 999999
Preset price is max. 6 digits.
If a price is set for a department where the amount entry type is"INHIBIT" or "OPEN", its amount entry type is set as below automat-ically.
"INHIBIT" "PRESET" "OPEN" "OPEN&PRESET"
MRS = 000000
[JOB#2110]PROGRAMMING DEPT. FUNCTIONS
XX: DEPT. code = 01 ∼ 50XXA: Not used (Fixed at "0")
XXB: Item validation printing B
Non compulsory 0
Compulsory 1
C: Tare table No. C
Non 0
Table No. 1 to 9
D: Scale entry D
Inhibit 0
Enable 1
Compulsory 2
XXE: SICS Function E
Normal 0
Single item cash sale 1
Single item finalize 2
XXF: Dept. type F
Normal 0
HASH 1
Bottle Return 2
XXG: Amount entry type G
Inhibited 0
Open 1
Preset 2
Open and preset 3
MRS (Dept, 01~20) = 0000001
[JOB#2111]DEPT. TAX STATUS AND SIGN PROGRAMMING
XX: DEPT. CODE = 01 - 50
A: Sign A
+ 0
– 1
B: Food stamp B
Non-food stampable 0
Food stampable 1
C: Taxable 4 C
Non taxable 0
Taxable 1
D: Taxable 3 D
Non taxable 0
Taxable 1
E: Taxable 2 E
Non taxable 0
Taxable 1
F: Taxable 1 F
Non taxable 0
Taxable 1
MRS = 000000
[JOB#2112]DEPT. HALO (limit) PROGRAMMING
XX: DEPT. CODE = 01 - 50A: Mantissa (HALO) = 1 - 9B: Exponent (HALO) = 0 - 7
Items A and B indicate A × 10B. Any amount below that value isenable within 9999999.
MRS = 17
SBTL@/FOR @/FOR
No change
For the next code
(Show Current code & Code entry)
1110 YYYYYY
CL
priceCA/ATXX
SBTL@/FOR @/FOR
For next code
No change
(Show Current code & Code entry)
2110 ABCDEFG
CL
CA/ATXX
SBTL@/FOR @/FOR
DEPT. CODE
For the next DEPT.
No change
(Show Current code & Code entry)
2111
CL
CA/ATABCDEFXX
SBTL@/FOR @/FOR CA/ATXX
DEPT. CODE
For the next DEPT.
No change
(Show Current code & Code entry)
2112 AB
CL
[JOB#2114]DEPT. TEXT PROGRAMMING
XXX: DEPT. CODE = 01 - 50
Characters can be entered by using the alphabetic keys (charact key)or the numeric keys (code entry).
Please refer to section 4 for further details.
MRS = DPT. XX
[JOB#2116]PROGRAMMING OF DEPT. GROUP
XX: DEPT. code = 01 - 50AA: Group No. = 0 - 9
MRS = 0
[JOB#2119]LINK NUMBER PROGRAMMING FOR DIRECT DEPT. KEYS
DEPT. code is assigned to the key no. Which has been programmedin JOB#951 programming.
XXX: Key No. = 001 - 068 AB: DEPT, CODE = 01 - 50
[JOB#2180]DEPARTMENT LOWER LIMITATION AGE PROGRAMMING
XX: Department code = 01 - 50 YY: Age: (00 ∼ 99), 00 = No Limitation
MRS = 0
[JOB#1200]Creating/assigning PLUs and the associated departments.
XXXXXX: PLU code = 01 - 999999AB: DEPT. code = 01 - 50
If the record of entered PLU code is not in PLU file at this program-ming, it will be created in PLU file.
MRS = (PLU 000001~000020) = 01
[JOB#1210]PLU PRICE PROGRAMMING
XXXXXX: PLU CODE = 1 - 999999
YYYYYY: Amount = 0 - 999999
If the record of the entered PLU code is not in the PLU file at thisprogramming step, the PLU code will be created.
If an amount is set for a PLU where the amount entry type is "IN-HIBIT" or "OPEN", its amount entry type is set as below automat-ically.
"INHIBIT" "PRESET" "OPEN" "OPEN&PRESET"
MRS = 000000
[JOB#1211]PLU BASE Q’TY PROGRAMMING
XXXXXX: PLU code = 1 - 999999ZZ: Base quantity = 00 - 99
If the record of the entered PLU code is not in the PLU file at thisprogramming step, the PLU code will be created.
2114
CL
All space
Character keyXX
DEPT. CODE
For the next DEPT.
(Show Current code & Code entry)
@/FOR @/FOR SBTL CA/AT
SBTL@/FOR @/FOR CA/ATXX
DEPT. CODE
Next code
No change
(Show Current code & Code entry)
2116 A
CL
SBTL@/FOR @/FOR CA/ATXXX
KEY No.
Next DEPT.
ABDEPT. code
inhibit
2119
SBTL@/FOR @/FOR CA/ATXX
No change
For the next code
(Show Current code & Code entry)
YY2180
CL
SBTL@/FOR @/FOR CA/AT
PLU code
No change
(Show Current code & Code entry)
ABXXXXXX
CL
1200
SBTL@/FOR @/FOR CA/AT
PLU CODE
For next code
No change
(Show Current code & Code entry)
YYYYYYXXXXXX
CL
1210
SBTLZZ@/FOR @/FOR CA/ATXXXXXX
PLU CODE
For the next PLU
No change
(Show Current code & Code entry)CL
1211
[JOB#2210]PLU function programming
XXXXXX: PLU code = 1-999999
A: Tare table No. ANon 0Table No. 1 to 9
B: Scale entry BInhibit 0Enable 1Compulsory 2
C: Amount entry type CInhibited 0Open 1Preset 2Open and preset 3Delete 4
If the record of the entered PLU code is not in the PLU file at thisprogramming step, the PLU code will be created.
MRS = 002
[JOB#2211]PLU TAX STATUS PROGRAMMING
XXXXXX: PLU code = 1- 999999
A: Sign A+ 0– 1
B: Food stamp BNon stampable 0Stampable 1
C: Taxable 4 CNon taxable 0Taxable 1
D: Taxable 3 DNon taxable 0Taxable 1
E: Taxable 2 ENon taxable 0Taxable 1
F: Taxable 1 FNon taxable 0Taxable 1
If the record of the entered PLU code is not in the PLU file at thisprogramming step, the PLU code will be created.
MRS = 000000
[JOB#2214]PLU TEXT PROGRAMMING
XXXXXX: PLU CODE = 1 - 999999
Characters can be entered by using alphabet keys (direct key) or thenumeric keys (code entry).
Please refer to section 4.
MRS = PLXXXXXX
[JOB#2219]PLU CODE DEFINITION FOR DIRECT PLU KEYS
XXX: Key No. = 001 - 068YYYYYY: PLU code = 1 - 999999
The PLU code is assigned to the key No. which has been preset inSRV JOB#951 programming.
[JOB#2220]LINKED PLU PROGRAMMING
XXXXXX: PLU code = 1 - 999999YYYYYY: PLU code = 1 - 999999
When the "SBTL" key is depressed without entering any number in(YYYYYY), there is no link.
The PLU code should already be defined when they are used in thisprogramming step.
MRS = 0
[JOB#2280]PLU LOWER LIMITATION AGE PROGRAMMING
XXXXXX: PLU code = 01 - 999999YY: Age = 00 - 99, 00 = No Limitation
MRS = 0
If the record of the entered PLU code is not in the PLU file at thisprogramming step, the PLU code will be created.
SBTL@/FOR @/FOR CA/AT
No change
PLU code
For next code
(Show Current code & Code entry)
ABCXXXXXX
CL
2210
SBTLABCDEF@/FOR @/FOR CA/ATXXXXXX
No change
For the next PLU
PLU code
CL
(Show current code & code entry)
2211
SBTLCharacter key@/FOR @/FOR CA/ATXXXXXX
For the next PLU
PLU code
All space
CL(Show Current code & Code entry)
2214
SBTL@/FOR @/FOR CA/AT
Next code
Key No.
inhibit
PLU code2219 YYYYYYXXX
SBTL2220 YYYYYY@/FOR @/FOR CA/ATXXXXXX
Max. 5 times
0
PLU CODE
SBTL@/FOR @/FOR CA/AT
No change
For the next code
(Show Current code & Code entry)
XXXXXX YY2280
CL
[JOB#2230]PLU CODE PROGRAMMING (range)
XXXXXX: Start PLU code = 1 - 999999YYYYYY: End PLU code = 1 - 999999
AB: Dept. code = 1-50
[JOB#2231]PLU function programming (RANGE)
XXXXXX: Start PLU code = 1 - 999999YYYYYY: End PLU code = 1 - 999999
A: Tare table No. ANon 0Table No. 1 to 9
B: Scale entry BInhibit 0Enable 1Compulsory 2
C: Amount entry type CInhibited 0Open 1Preset 2Open and preset 3Delete 4
MRS = 000
If the record of the entered PLU code is not in the PLU file at thisprogramming step, the PLU code will be created.
[JOB#2232]PLU TAX STATUS PROGRAMMING (RANGE)
XXXXXX: Start PLU code = 1 - 999999YYYYYY: End PLU code = 1 - 999999
A: Sign A + 0– 1
B: Food stampable B
Non-food stampable 0
Food stampable 1
C: Taxable 4 C
Non taxable 0
Taxable 1
D: Taxable 3 D
Non taxable 0
Taxable 1
E: Taxable 2 E
Non taxable 0
Taxable 1
F: Taxable 1 F
Non taxable 0
Taxable 1
[JOB#1310]RATE PROGRAMMING
XXX: Function No.YYYY. YYYY: Rate
FunctionNo.
Function Entry range Remarks
1 (–)1
0 to 999999 (–) unit price 2 (–)2
3 (–)3
4 (–)4
5 %1
0 to 100.00 % rate 6 %2
7 %3
8 %4
65 Conversion 10 to 9999.9999 Rate 66 Conversion 2
67 Conversion 3
MRS = 0
Note: You must input the decimal key for fractional entries.
[JOB#2311]MISC KEY PROGRAMMING 1
XXX: Function No.
Function No. Function
1 (–)1
2 (–)2
3 (–)3
4 (–)4
5 %1
6 %2
7 %3
8 %4
YYYYYYXXXXXX2230
AB
@/FOR
CA/AT
@/FOR @/FORPLU CODE PLU CODE
No change (Same deta as start PLU)
SBTL
YYYYYYXXXXXX2231
ABC
@/FOR
CA/AT
@/FOR @/FORPLU CODE
No change (Same deta as start PLU)
SBTL
YYYYYYXXXXXX2232
ABCDEF
@/FOR
CA/AT
@/FOR @/FORPLU CODE
No change (Same deta as start PLU)
SBTL
SBTL1310 YYYY.YYYY@/FOR @/FOR CA/ATXXX
Function No. Rate
No change
SBTL2311 ABCDEF@/FOR @/FOR CA/ATXXX
Function No.
No change
A: Sign A
+ 0
– 1
B: Food stamp B
Non food stampable 0
Food stampable 1
C: Taxable 4 C
Non taxable 0
Taxable 1
D: Taxable 3 D
Non taxable 0
Taxable 1
E: Taxable 2 E
Non taxable 0
Taxable 1
F: Taxable 1 F
Non taxable 0
Taxable 1
MRS = 100000
[JOB#2312, 2322]HALO PROGRAMMING
XXX: Function No.A: Mantissa (0 to 9)B: Exponent (0 to 7) for (–) and Tax
Exponent (0 to 8) for RA/PO and each media
JOB#Function
No.Function Remarks
2312
1 (–)1
Item B is specificablewithin the range from 0 to7.
2 (–)2
3 (–)3
4 (–)4
32 TAX
64 RAItem B is specificablewithin the range from 0 to8.
65 RA2
66 PO
67 PO2
2322
61 CA1
Item B is specificablewithin the range from 0 to8.
62 CA2
86 CHK
87 CHK2
76 CH1
78 CH2
80 CH3
82 CH4
84 CH5
Entry range, system: A × 10B
MRS = 17 ((–)1-(–)4, TAX)18 (RA, RA2, PO, PO2, CA1, CA2, CHK, CHK2, CH1 - CH5)
[JOB#2313]MISCELLANEOUS KEY PROGRAMMING (% HALO)
XXX: Function No.YYY. YY: % HALO
FunctionNo.
Function Remarks
5 %16 %27 %38 %4
[JOB#2314]TEXT PROGRAMMING FOR MISC KEYS
XXX: FUNCTION NO.
Characters can be entered by using the character keys (direct key) orthe numeric keys (code entry). The key entry sequence for enteringone character by numeric keys is as follows:
XXX → 00 key XXX: CHARACTER CODE (3DIGITS)
Please refer to section 4 for further details.
F-NO. FUNCTION DEFAULT TEXT
1 (–)1
2 (–)2
3 (–)3
4 (–)4
5 %1
6 %2
7 %3
8 %4
9 NET1
10 TAXABLE1 ST
11 GROSS TAX1
12 REFUND TAX1
13 NET TAX1
14 EXEMPT TAX1
15 TAXABLE2 ST
16 GROSS TAX2
17 REFUND TAX2
18 NET TAX2
19 EXEMPT TAX2
20 TAXABLE3 ST
21 GROSS TAX3
22 REFUND TAX3
23 NET TAX3
24 EXEMPT TAX3
25 TAXABLE4 ST
26 GROSS TAX4
27 REFUND TAX4
28 NET TAX4
29 EXEMPT TAX4
SBTL23122322
AB@/FOR @/FOR CA/ATXXXFunction code
No change
SBTL2313 YYY.YY@/FOR @/FOR CA/ATXXX
No change
SBTL2314 @/FOR @/FOR CA/AT
Function number Max. 8 char.
All space
XXX Character key
F-NO. FUNCTION DEFAULT TEXT
30 GROSS M-TAX
31 REFUND M-TAX
32 NET M-TAX
33 NON GST SUBTOTAL
34 PST TOTAL (For "A" version)
35 GST TOTAL (For "A" version)
36 FS1 FORGIVE
37 FS2 FORGIVE
38 FS3 FORGIVE
39 TOTAL TAX
40 NET
41 NET2
42 COUPON PLU
43 VENDER COUPON UPC
44 ITEM VOID
45 SBTL VOID
46 MANAGER VOID
47 VOID MODE
48 REFUND
49 HASH VOID
50 HASH REFUND
51 NO SALE
52 VP COUNTER
53 BILL(SLIP) COUNTER
54 DRAWER COUNTER
55 PBAL
56 SERVICE
57 DEPOSIT
58 DEPOSIT REFUND
59 CUSTOMER
60 NET3 (SALES)
61 CASH
62 CASH2
63 FS SALE
64 RA
65 RA2
66 PO
67 PO2
68 CHECK CASHING
69 CHECK CHANGE
70 FS CHANGE
71 CONVERSION1
72 CONVERSION2
73 CONVERSION3
74 CONVERSION4
75 FS IN DRAWER
76 GROSS CHARGE1
77 REFUND CHARGE1
78 GROSS CHARGE2
79 REFUND CHARGE2
80 GROSS CHARGE3
81 REFUND CHARGE3
82 GROSS CHARGE4
83 REFUND CHARGE4
84 GROSS CHARGE5
F-NO. FUNCTION DEFAULT TEXT
85 REFUND CHARGE5
86 CHECK
87 CHECK2
88 CASH+CHECK IN DRAWER
89 CASH IN DRAWER
90VAT EXEMPT (For DOUGHNUTTAX Type1) (For "A" version)
91 AVERAGE (HOURLY REPORT)
92 GROUP1
93 GROUP2
94 GROUP3
95 GROUP4
96 GROUP5
97 GROUP6
98 GROUP7
99 GROUP8
100 GROUP9
101 PRICE 1 FOR UPC
102 PRICE 2 FOR UPC
103 PRICE 3 FOR UPC
104 (+)DEPT TOTAL
105 (–)DEPT TOTAL
106 HASH (+)DPT TOTAL
107 HASH (–)DPT TOTAL
108 BOTTLE (+)DPT TOTAL
109 BOTTLE (–)DPT TOTAL
110 SUBTOTAL
111 MDS SBTL
112 TOTAL
113 CHANGE
114 FS SBTL
115 FS TEND
116 FS CHANGE
117 ITEMS
118 COPY RCPT TITLE
119 DEPT REPORT TITLE
120 GROUP REPORT TITLE
121 PLU REPORT TITLE
122 CATEGORY REPORT TITLE
123 TRANSACTION REPORT TITLE
124 CID REPORT TITLE
125 CASHIER REPORT TITLE
126 HOURLY REPORT TITLE
127 DAILY NET REPORT TITLE
128 ZERO SALES REPORT TITLE
129 EAN REPORT TITLE
130 NON ACCESSED EAN TITLE
131 PBLU REPORT TITLE
132 PRICE CHANGE TITLE
133 FINAL
134 BALANCE
135 SLIP PRINT MESSAGE
136 BALANCE FORWARD
[JOB#2315]MISC KEY PROGRAMMING (%)
XXX: Function No.
A: % type ASubtotal % 0Item % 1
Function No. Function Remarks5 %16 %27 %38 %4
MRS = 0
[JOB#2316]MISC KEY PROGRAMMING (–)
XXX: Function No.
A: (–) type ASubtotal (–) 0Item (–) 1
Function No. Function Remarks1 (—) 12 (—) 23 (—) 34 (—) 4
MRS = 0
[JOB#2320]MEDIA KEY PROGRAMMING
XXX: Function No.
FunctionNo.
Function A B C D E F G H
61 CA 162 CA 276 CH 178 CH 280 CH 382 CH 484 CH 586 CHK87 CHK256 SERVICE
115 FS TEND133 FINAL
Items marked with an ( ) are programmable.
A : Not used (Fixed at "0")
B: Bill (Slip) print BNoncompulsory 0Compulsory 1
B: Footer print on receipt BNo 0Yes 1
C: Non-add code entry CNon compulsory 0Compulsory 1
D: Change due DEnable 0Disable 1
E: VP ENon compulsory 0Compulsory 1
F: Drawer opening FYes 0No 1
G: Entry of amount tended GNon compulsory (Cash, Check)Inhibit (CH1 to CH5)
0
Compulsory 1
MRS=0000000
[JOB#2321]MEDIA KEY FUNCTION PROGRAM (AMOUNT HALO)
XXX: Function No.YYYYYYYYY: Limitation amount
Func. No.
Function Entry range MRS
89 CID (Sentinel) 0 to 9999999.99 9999999.9969 CHK CHANGE 0 to 999999.99 999999.9965 CA/CHK 0 to 999999.99 999999.99
[JOB#2326]MEDIA KEY PROGRAMMING – 2
XXX: Function No.
Function No. Function61 CA 162 CA 276 CH 178 CH 280 CH 382 CH 484 CH 586 CHK87 CHK2
SBTL2315 A@/FOR @/FOR CA/ATXXX
No change
SBTL2316 A@/FOR @/FOR CA/ATXXX
No change
SBTL2320 ABCDEFGH@/FOR @/FOR CA/ATXXX
No change
SBTL2321 YYYYYYYY@/FOR @/FOR CA/ATXXX
No change
SBTL@/FOR @/FOR CA/AT
No change
ABCD2326 XXX
A: Taxable 4 delete A
No 0
Yes 1
B: Taxable 3 delete B
No 0
Yes 1
C: Taxable 2 delete C
No 0
Yes 1
D: Taxable 1 delete D
No 0
Yes 1
MRS=0000
[JOB#1500]CASHIER CODE DEFINITION
XXX: Cashier No.= 1 - 99YYYY: Cashier code = 00 - 99
MRS = Cashier code 1 - 4.
[JOB#1514]CASHIER NAME PROGRAMMING
YYYY: Cashier code = 01 - 99
Characters can be entered by using the character keys (direct key) orthe numeric keys (code entry). The key entry sequence for enteringone character by numeric keys is as follows:
XXX 3 00 KEY XXX: Character code (3 digits)
Please refer to section 4.Max. 8 charactersMrs = ’Space’
[JOB#2510]CASHIER PROGRAMMING
YYYY: Cashier code = 01~99
A: Drawer No. H
Not open 0
Drawer No. 1-2
MRS = 1
[JOB#2610]DATE SETTING
XXYYZZ: Date (Year-Month-Day/Day-Month-Year/Month-Day-Year)
The date entry format complies with the setting of SRV JOB#912.MRS = 010100
[JOB#2611]TIME SETTING
XX: Hour (00 - 23)YY: Minute (00 - 59)MRS = 0
[JOB#2612]MACHINE NUMBER SETTING
XXXXXX: Machine number (0 - 999999)MRS = 0
[JOB#2613]CONSECUTIVE NUMBER SETTING
XXXX: Consecutive number (0000 - 9999)MRS = 0000
[JOB#2614]LOGO TEXT PROGRAMMING
X: 1 - 6 1 (24 char.)2 (24 char.)3 (24 char.)4 (24 char.)5 (24 char.)6 (24 char.)
Characters can be entered by using the character keys (direct key) orthe numeric keys (code entry).The key entry sequence for entering one character by numeric keysis as follows:
XXX 00 Key XXX: Character code (3 digits)Please refer to section 4 for further details.
MRS =
NOTE: This programming is related to SRV JOB# 912D preset."6-line header": All 6 lines are preset."3-line header": Upper 3 lines (1st-3rd line) are preset."Graphic logo and 3-line footer": Lower 3 lines (4 th - 6 th
line) are preset"3-line footer": Lower 3 lines (4th-6th line) are preset."3-line header and 3-line footer": All 6 lines are preset. (1st-
3rd: Header, 4th-6th:Footer)
"Graphic logo only": No line is preset
SBTL1500 YY@/FOR @/FOR CA/ATXX
No change
SBTL1514 @/FOR @/FOR CA/AT
All space
YY Character key
SBTL2510 A@/FOR @/FOR CA/ATYY
No change
2610 @/FOR CA/ATXXYYZZ
0
2611 @/FOR CA/ATXXYY
0
2612 @/FOR CA/ATXXXXXX
0
2613 @/FOR CA/ATXXXX
2614 Character key@/FOR @/FOR SBTL CA/ATX
Position code
All space
[JOB#2615]
SLIP PRINTER OPTIONSProgramming of the limits to No. of times of validation printing.
VV: Initial slip feed line = 0 - 64XX: Slip print max. line No. = 0 - 99Y: No. of times of validation printing = 0 - 9 X: Not used (Fixed at "0")
MRS = 009910
Note: Max. line number of the slip must be set to a value less thanthe length of the of bill included the initial feed line.
[JOB#2616]OPTIONAL FEATURE
XX: 1 MRS = 00000000
A: OP X/Z report AEnable 0Disable 1
B: PO operation in REG mode BEnable 0Disable 1
C: Refund type of sale function in REGmode
C
Enable 0Disable 1
D: "RFND" key entry in REG mode DEnable 0Disable 1
E: Direct void function in REG mode EEnable 0Disable 1
F: In direct void in REG mode FEnable 0Disable 1
G: Subtotal void in REG mode GEnable 0Disable 1
H: Refund VP (SLIP only) HNon compulsory 0Compulsory 1
XX: 2 MRS = 00000000
A: The first last item void AEnable 0Disable 1
B, C: Not used (Fixed at "00")
D: Printing of the number of purchases DNo 0Yes 1
E: Time print EYes 0No 1
F: Printing of journal FFull print 0Journal select 1
G: Item VP (SLIP only) GEnable 0Disable 1
H: (–) VP (SLIP only) HNon compulsory 0Compulsory 1
XX: 3 MRS = 00000000
A: Zero skip in UPC report AYes 0No 1
B : Not used (Fixed at "0")
C: Zero skip in Cashier report CYes 0No 1
D: Zero skip in Transaction report DYes 0No 1
E: Zero skip in Dept. report EYes 0No 1
F: Zero skip in PLU report FYes 0No 1
G: Zero skip in Hourly report GYes 0No 1
H: Zero skip in Daily net report HYes 0No 1
XX: 4 NOT USED MRS = 00000000XX:5 MRS = 00000000
A,B,C,D,E: Not used (Fixed at "00000")
F: UPC price shift system FMGR & REG 0MGR 1
G: UPC price shift system GAuto 0Manual 1
H: Return timing at "Auto" (XX:5-G = 0) HBy one item 0By one receipt 1
X: 6 NOT USED MRS = 00000000X: 7 MRS = 00000000
2615 @/FOR CA/AT
0
WXXYZ
@/FOR @/FOR SBTL CA/ATXX
No change
ABCDEFGH2616
A, B: Not used (Fixed at "00")
C: No sale in REG mode CEnable 0Disable 1
D: Finalization in REG mode whenSBTL is zero
D
Enable 0Disable 1
E: Printing of item in PBLU transactionon SLIP
E
Yes 0No 1
F, G, H: Not used (Fixed at "000")X: 8 MRS = 00000000
A, B, C, D: Not used (Fixed at "0000")
E: Validation of check cashing (SLIP ONLY) E
Non compulsory 0
Compulsory 1
F: Validation of RA (SLIP ONLY) F
Non compulsory 0
Compulsory 1
G: Validation of PO (SLIP ONLY) G
Non compulsory 0
Compulsory 1
H: Not used (Fixed at "0")X: 9 MRS = 00000000
A, B: Not used (Fixed at "00")
C: BIRTHDAY print on printer C
Yes 0
No 1
D, E, F, G, : Not used (Fixed at "0000")
H: Footer Graphic logo printing at theend of receipt
H
No 0
Yes 1
XX:10 MRS = 00000000A,B: Not used (Fixed at "00")
C: Learning function UPC entry C
Yes 0
No 1
D, E, F, G, H: Not used (Fixed at "00000")
X: 11 NOT USED MRS = 00000000XX:12 MRS = 00000000
A, B, C, D, E, F, G: Not used (Fixed at "0000000")
H: Price change function in REG mode H
Enable 0
Disable 1
XX:13 MRS = 00000000A,B,C: Not used (Fixed at "000")
D: Printing of price shift text on theReceipt/Journal
D
Yes 0
No 1
E: Not used (Fixed at "0")
F: Treating EAN8 code 200 as PLU F
Yes 0
No 1
G: Not used (Fixed at "0")
H: Price entry after ISBN or ISSN H
Compulsory 0
Inhibited 1
[JOB#2617]PROGRAMMING THE TIME INTERVAL FOR THE TILL TIMER
XXX: 0 - 255 sec
MRS = 000
[JOB#2618]SCALE TABLE PROGRAMMING
X: Table No. = 1 - 9
YYYY: Weight = 0 - 99.99 ( Enter without decimal point.)
MRS = 0
[JOB#2619]HOURLY REPORT (Starting time)
a: Memory type A
30 minutes (24 hour) 0
60 minutes (24 hour) 1
bb: Starting time (hour): 00 - 23
ex)
Case 1.
X1 Hourly report (#160) (30 min, start time = 7]
2617 @/FOR CA/ATXXX
0
YYYY
0
2618 XUPC code
CA/ATSBTL
@/FOR @/FOR
2619 @/FOR CA/ATabb
0
2619 @/FOR CA/AT007
[JOB#2620]STACK REPORT
XX: JOB#SSSSSS: Start codeEEEEEE: End code
JOB# REPORT NAME TYPE00 General07 UPC zero sales09 All UPC ALL10 DEPT.13 DEPT. All group20 PLU RANGE -127 PLU zero sales RANGE -129 PLU category RANGE -130 Transaction31 CID50 All cashier60 Hourly RANGE -2 (only X report)60 Hourly ALL70 Daily net80 PBLU RANGE-2
[ ]
A max of 70 steps are programmable. "1 step" means the memorysize used for one no range type JOB#.
The RANGE-1 type JOB# means "8 steps".
The RANGE-2 type JOB# means "6 steps".
For example)
The memory size for programming JOB#00, 20 and 50 is 10 steps.(ie. 1 step for JOB#00, 8 steps for JOB#20, and 1 step for JOB#50. )
[JOB#2630, 2631, 2632]SECRET CODE PROGRAMMING
#2630: PGM1 mode
#2631: X1/Z1 mode
#2632: X2/Z2 mode
XXXX: Secret code = 0000 - 9999
If "0" is entered, "compulsory secret code entry" is canceled.
MRS = 0
[JOB#2642]VP TEXT PROGRAMMING
X: Position code = 1 - 3
1 Block Max. 24 characters
MRS = " "" ""FOR DEPOSIT ONLY"
[JOB#2643]SLIP TEXT PROGRAMMING
X: Position code = 1 - 3
1 Block Max. 24 characters
MRS = "SPACE""SPACE""SPACE"
[JOB#2690]THE ASSIGNMENT OF RS232 FUNCTION BY EACH DEVICE
CAUTION: Do not assign two different devices to the same channelNo.
X: 1 MRS = 0000
A: Channel No. for ON-LINE ANo 0Channel No. (1 or 8) 1 or 8
B: Channel No. for Print data sending BNo 0Channel No. (1 or 8) 1 or 8
C: Channel No. for Scale CNo 0Channel No. (1 or 8) 1 or 8
D: Not used (Fixed at "0")X: 2 MRS = 0000
A: Channel No. for Barcode reader ANo 0Channel No. (1 or 8) 1 or 8
B,C,D: Not used (Fixed at "000")X:3 MRS = 0000
A: Not used (Fixed at "0")
B: Channel No. for Slip printer (TM295) BNo 0Channel No. (1 or 8) 1 or 8
C,D:Not used (Fixed at "00")
2620 @/FOR
XX @/FOR SSSSSS @/FOR EEEEEE
All delete
No range
Next JOB# (max.=20)
SBTL CA/AT
2630 @/FOR CA/ATXXXX
0
26312632
Characterkey
All space
2642 XPosition code
CA/ATSBTL
@/FOR @/FOR
Characterkey
All space
2643 XPosition code
CA/ATSBTL
@/FOR @/FOR
2690 ABCD@/FOR @/FOR SBTL CA/ATX
0
Channel No.: 0 = No connection1 = Standard port 22-7 = Not used8 = Standard port 1
NOTE: There can be only 2 devices supported by the ECR at anyone time.Will ENTRY ERROR is occurred when a device has been setas the same channel that is used by another device.
[JOB#2691]BARCODE READER PROGRAMMING
W: Data bitW
8 bits 07 bits 1
X: Parity bit XEven 0Odd 1Non 2
Y: Stop bit Y2 bits 01 bit 1
Z: Transmission speed Z4800 bps 09600 bps 119200 bps 2
MRS = 1110(For ER-A6HS1)
[Job# 2710]TAX TABLE PROGRAMMING
72 BREAKPOINTS CAN BE PROGRAMMED FOR EACH TAX-TABLE.
(When the interval between break point is 1 dollar or more and lessthan 100 dollar, 36 breakpoints is programmed for each table.)
DEPRESSION OF THE SBTL KEY AT THE FOLLOWING POINTSWILL RESULT IN A TAX TABLE DELETE OPERATION.
A: INTERVAL BETWEEN BREAKPOINTS IS = 11 DOLLAR OR MORE AND LESS THAN 100 DOLLAR
INTERVAL BETWEEN BREAKPOINTS IS = 0BELOW 1 DOLLAR
B: TABLE 1 PROGRAMMING = 1TABLE 2 PROGRAMMING = 2TABLE 3 PROGRAMMING = 3TABLE 4 PROGRAMMING = 4
TAX RATE : 0.0000 - 99.9999CYCLE : 0 - 9999INITIAL TAX : 0 - 999LOWER TAX LIMIT : 0 - 99999BREAK POINT : 0 - 99999
MRS = NO TAX
[JOB#2711]TAX RATE PROGRAMMING
DEPRESSION OF THE ST KEY AT FOLLOWING POINTS WILLRESULT IN A TAX TABLE DELETE OPERATION.
A: Tax programming ATax1 1Tax2 2Tax3 3Tax4 4
xxx.xxxx: % TAX rate = 0.0000-999.9999%
LOWER TAX LIMITATION = 0.00 to 999.99
(This is invalid in VAT system.)
MRS = 0
[JOB#2715]QUANTITY FOR DOUGHNUT EXEMPT ( For Canadian TAX )
XX: Quantity for doughnut TAX exempt = 0 - 99
MRS = 0
[JOB#2810]PBLU code ( The range programming of available PBLU codes)
XXXX:Start code = 1 - 9999
YYYY:End code = 1 - 9999
MRS = 0001(Start code) / 9999(End code)
2691 CA/AT@/FOR WXYZ
0
AB
Declaration of TAX TAX rate
XXXX
Initial TAXCycle
XXXXX
Break pointLower TAX limit
2710
XXX
XXXXX
@/FOR
CA/AT
@/FOR @/FORXX.XXXX
@/FOR @/FOR
@/FOR @/FOR
Declaration of TAX TAX rate
Lower tax limitfor add tax.
When lower taxlimit is 0.
2711 A XXX.XXXX
XXXXX
@/FOR
CA/AT
CA/AT
@/FOR @/FOR
2715 CA/AT@/FOR XX
0
2810 @/FOR XXXX CA/AT@/FOR YYYY
0
[JOB#2900]
Note:(This JOB must be performed at X2/Z2 mode position.)
AUTO KEY SETTING
(Auto key function)
• This machine has [AUTO] key functions which can be programmedby the following key-sequence.
• When [AUTO] key is depressed, the machine works the same asthe programmed key-sequence programmed.
<Example>
Mode switch
⇓
(X2/Z2)
(REG)
(X2/Z2)
(REG)
[JOB#2910, 2911]Training mode start (#2910), End (#2911)
<Training mode>
All operations is same as REG-mode operation.In the training mode, the consecutive number is printed the as samenumber on receipt/journal printer and slip printer.In the training mode, the consecutive number is incremented by eachtransaction.
[JOB#2990]THERMAL PRINTER PROGRAMMING
X, Y: Not used (Fixed at "10")
ZZ: Selecting of light and shade ZZ
80% for standard 00
90% standard 50
100% standard 99
MRS = 1050
Entries for XY will always result in a setting of "10"(It is always set as "10" even if "00"is entered.)
3. Programming by direct key entry
1) PRICE PROGRAMMING for DEPT.
XX: DEPT. code = 01 to 50
YYYYYY: UNIT PRICE (Max. 6 digits)
MRS = 0
If [DPTn] (same as the displayed department number) or [DEPT#]is depressed, the programming mode is changed from "PRICEPROGRAMMING" to "FUNCTION PROGRAMMING" (from"FUNCTION PROGRAMMING" to "PRICE PROGRAMMING").
2) FUNCTION PROGRAMMING for DEPT.
XX: DEPT. code = 01 to 50
A: Sign A
+ 0
– 1
B: Food stamp B
Non-food stampable 0
Food stampable 1
C: Taxable4 C
Non taxable 0
Taxable 1
D: Taxable3 D
Non taxable 0
Taxable 1
2900 (Free key)AUTO
Max.25
@/FOR CA/AT
AUTO2
AUTO3
AUTO4
AUTO5
AUTO
AUTO2
AUTO3
AUTO4
AUTO5
Delete
AUTO10 AUTO10
2900 @/FOR AUTO PLU1 100 DEPT2 AUTO CA/AT
Key entry R/J Display Comment
AUTO PL000001 $1.10
PL000001 $1.00
PL0000001 same as entryPLU11.10
1
10
100
DEPT02 1.10
same as entry1
same as entry0
same as entry0
same as entryDEPT2
2900 @/FOR AUTO2 PLU1 100 DEPT2 CA/ATAUTO2
Key entry R/J Display Comment
DEPT 1 DEPT01 DEPT01 1.10
100
CHANGE 0.00
same as entry1
same as entry0
same as entry0
same as entryCA/AT
AUTO 2
$1.00
***TOTAL $1.00
CASH $1.00
CHANGE $0.00
10
1
2910/2911 @/FOR CA/AT
0
2990 XYZZ@/FOR CA/AT
DEPTn
Not changed
For next code
YYYYYY
DEPT#XX
CA/ATSBTL
DEPTn
Not changed
For next code
ABCDEFGHI
DEPT#XX
SBTL CA/AT
E: Taxable2 E
Non taxable 0
Taxable 1
F: Taxable1 F
Non taxable 0
Taxable 1
G: SICS Function G
Normal 0
Single item cash sale 1
Single item finalize 2
H: Limitation (Mantissa) = 0~9
I: Limitation (Exponent) = 0~7
MRS = NORMAL, 17 HALO
If [DPTn] (same as the displayed department number) or[DEPT#] is depressed, the programming mode is changed from"PRICE PROGRAMMING" to "FUNCTION PROGRAMMING"(from "FUNCTION PROGRAMMING" to "PRICE PROGRAM-MING").
Double depression of the [DPTn] or [DEPT#] key is necessaryfor the first entry.
3) PRICE & MODIFY PROGRAMMING for (–) KEYS.Mode : PGM1 / PGM2
XXXXXX: UNIT PRICE (Max. 6 digits)
MRS = 0
If the same [(–)n] key is depressed, the programming mode ischanged from the "PRICE PROGRAMMING" to "FUNCTION PRO-GRAMMING" (from "FUNCTION PROGRAMMING" to "PRICEPROGRAMMING").
4) FUNCTION PROGRAMMING for (–) KEYS.Mode : PGM2
A: Sign A
+ 0
– 1
B: Food stamp B
Non-food stampable 0
Food stampable 1
C: Taxable4 C
Non taxable 0
Taxable 1
D: Taxable3 D
Non taxable 0
Taxable 1
E: Taxable2 E
Non taxable 0
Taxable 1
F: Taxable1 F
Non taxable 0
Taxable 1
G: Not used (Fixed at "0")
H: Limitation (Mantissa) = 0~9
I: Limitation (Exponent) = 0~7
MRS = NORMAL, 17 HALO
If the same [(–)n] key is depressed, the programming mode ischanged from the "PRICE PROGRAMMING" to "FUNCTION PRO-GRAMMING" (from "FUNCTION PROGRAMMING" to "PRICEPROGRAMMING").
5) PLU PRESET PRICE SETTINGMode : PGM1 / PGM2
XXXXXX: PLU CODE (1 to 999999)YYYYYY: UNIT PRICE (6 digits)
If the record of the entered PLU code is not in the PLU file at thisprogramming step, the PLU code will be created.
MRS = 0
If the [PLU] or [PLUn] key is depressed, the programming mode ischanged from the "PRICE PROGRAMMING" to "ATTRIBUTEPROGRAMMING" and is changed to the "PLU ASSOCIATIONPROGRAMMING" by depressing the same key again.(Caution!!)The associated department is changed if the operator depressesthe [DPTn] key instead of [PLUn] key by mistake at this program-ming step.
6) PLU ASSOCIATION TO DEPARTMENTSMode : PGM1 / PGM2
XXXXXX: PLU CODE (1 to 999999)YY: Dept. code (1 to 50)If the record of entered PLU code is not in PLU file at this program-ming, it will be created in PLU file.
MRS = 01
If the [PLU] or [PLUn] key is depressed, the programming modeis changed from the "PRICE PROGRAMMING" to "ATTRIBUTEPROGRAMMING" and then changed to the "PLU ASSOCIA-TION PROGRAMMING" by depressing the same key again.
Not changed
XXXXXX CA/ATSBTL(-)n
Not changed
ABCDEFGHI(-)n (-)n CA/AT@/FOR
Not changed
XXXXXXPLU code
for next code
YYYYYYPLU
PLUn
SBTL CA/AT
XXXXXXPLU code
PLU delete
PLU
PLUn
for next code
DPTn
VOID
YY
Not changed DEPT#
SBTL
CA/AT
Note:The associated department is changed if the operator depress[DPTn] key instead of [PLUn] key by mistake at this program-ming step.
Triple depression of the [PLU] or [PLUn] key is necessary for thefirst entry.
7) PROGRAMMING OF PLU/SUBDEPTMode : PGM2
XXXXXX: PLU CODE (1 to 999999)
A: Sign A
+ 0
– 1
B: Food stamp B
Non-food stampable 0
Food stampable 1
C: Taxable4 C
Non taxable 0
Taxable 1
D: Taxable3 D
Non taxable 0
Taxable 1
E: Taxable2 E
Non taxable 0
Taxable 1
F: Taxable1 F
Non taxable 0
Taxable 1
G: Amount entry type G
Inhibited 0
Open 1
Preset 2
Open and preset 3
Delete 4
If the record of the entered PLU code is not in the PLU file at thisprogramming step, the PLU code will be created.
MRS = 002
* If the [PLU] or [PLUn] key is depressed, the programming modeis changed from the "PRICE PROGRAMMING" to "ATTRIBUTEPROGRAMMING" and then changed to the "PLU ASSOCIA-TION PROGRAMMING" by depressing the same key again.
Double depression of [PLU] or [PLUn] key is necessary for thefirst time.
8) UPC PRESET PRICE SETTINGMode:PGM1/PGM2
XXXXXXXXXXXXX: UPC code
YYYYYY: Unit price (6 digits)
If the record of the entered UPC code is not in the UPC file at thisprogramming step, the UPC code will be created.
MRS = Nothing (Default = 0)
The default value is set when the new UPC record is created.
At this time, Price1 is shown.If the [UPC] key is depressed, the programming mode is changedfrom "PRICE PROGRAMMING" to "ATTRIBUTE PROGRAM-MING" and then changed to the "UPC ASSOCIATION PRO-GRAMMING" by depressing the same key again.
9) PROGRAMMING OF UPCMode : PGM2
XXXXXXXXXXXXX: UPC code
A: Sign A+ 0- 1
B: Food stamp BNo 0Yes 1
C: Taxable4 CNon taxable 0Taxable 1
D: Taxable3 DNon taxable 0Taxable 1
E: Taxable2 ENon taxable 0Taxable 1
F: Taxable1 FNon taxable 0Taxable 1
G: Record delete method GDelete at X/Z non-accessedUPC deleting JOB
0
Non delete 1Delete now 2
If the record of the entered UPC code is not in the UPC file at thisprogramming step, the UPC code is created.
MRS = nothing ( Default = 0000000)
The default value is set when the new UPC record is created.
Not changed
XXXXXX
PLU code
for next code
ABCDEFG @/FOR CA/ATPLU
PLUn
XXXXXXXXXXXXX UPC
(Scanning)
YYYYYY
No change
P1
CA/ATSBTL
P2
P3(Pricel shift)
(Pricel)
XXXXXXXXXXXXX UPC
(Scanning)
ABCDEFG
No change
CA/AT@/FORUPC code
If the [UPC] key is depressed, the programming mode ischanged from the "PRICE PROGRAMMING" to "ATTRIBUTEPROGRAMMING" and then changed to the "UPC ASSOCIA-TION PROGRAMMING" by depressing the same key again.
Either "Double depression of the [UPC] key" or "a depression of[UPC] key after scanning" is necessary for the first entry.
10) UPC ASSOCIATION TO DEPARTMENTSMode : PGM1/PGM2
XXXXXXXXXXXXX: UPC code
YY: DEPT. code = 1 to 50
If the record of the entered UPC code is not in the UPC file at thisprogramming step, the UPC code will be created.
MRS = nothing ( Default = 01)
The default value is set when the new UPC record is created byanother programming JOB.
If the [UPC] key is depressed, the programming mode ischanged from the "PRICE PROGRAMMING" to "ATTRIBUTEPROGRAMMING" and then changed to the "UPC ASSOCIA-TION PROGRAMMING" by depressing the same key again."Triple depression of the [UPC] key" or "Double depression ofthe [UPC] key after scanning" is necessary for the first entry.
11) PROGRAMMING RATE FOR %KEY.Mode : PGM1 / PGM2
XXX.XX: 0.00 to 100.00
MRS = 0.00%
If the same [%n] key is depressed, the programming mode ischanged from the "RATE PROGRAMMING" to "FUNCTION PRO-GRAMMING".
12) PROGRAMMING FOR %KEY.Mode : PGM2
A: Sign A+ 0– 1
B: Food stamp BNon-food stampable 0Food stampable 1
C: Taxable4 CNon taxable 0Taxable 1
D: Taxable3 DNon taxable 0Taxable 1
E: Taxable2 ENon taxable 0Taxable 1
F: Taxable1 FNon taxable 0Taxable 1
MRS = 100000
If the same [%n] key is depressed, the programming mode ischanged from the "RATE PROGRAMMING" to "FUNCTION PRO-GRAMMING" (from "FUNCTION PROGRAMMING" to "PRICEPROGRAMMING").
13) PROGRAMMING RATE FOR CONVERSION KEYMode : PGM1 / PGM2
XXXX.XXXX: 0.0000 to 9999.9999MRS = 0.00000
14) PROGRAMMING FOR MEDIA KEYS &FUNCTION KEYS.Mode : PGM2
A: Mantissa (0 to 9)
B: Exponent (0 to 8)
MRS = 18 digits. (RA, PO, CASH2, CHn, CHKn)17 digits. (TAX)
In case of the Manual TAX HALO programming:At the first entry, the [TAX]-key must be pushed two times.After entry of the [@/FOR]-key, the [TAX]-key is only requiredone time after.
XXXXXXXXXXXXX UPC
(Scanning)UPC delete
DEPTn
DEPT#
VOID
Not changed
YY
CA/AT
SBTL
UPC code
Not changed
SBTL CA/AT%n XXX.XX
Not changed
ABCDEF%n %n CA/AT@/FOR
CNV1
Not changed
XXX.XXX
CNV2
CNV3
CA/ATSBTL
RA
PO
CASH2
CHn
CHKn
TAX
AB CA/AT@/FOR
TAX TAX
15) DATE, TIME PROGRAMMING.Mode : PGM2
DATE: date entry format follows SRV JOB#912-A settings (6 digits)TIME: 24 hour system (4 digits)
MRS = DATA: 01/01/00TIME: 00:00
16) TAX TABLE PROGRAMMING
72 BREAKPOINTS CAN BE PROGRAMMED FOR EACH TAX-TABLE.
(If the interval between break points is 1 dollar or more and less than 100dollar, a maximum of 36 breakpoints is programmed for each table.)
DEPRESSION OF THE SBTL KEY AT THE FOLLOWING POINTSWILL RESULT IN A TAX TABLE DELETE OPERATION.
A: INTERVAL BETWEEN BREAKPOINTS1 DOLLAR OR MORE AND LESS THAN 100 DOLLAR = 1BELOW 1 DOLLAR = 0
B: TAX TABLE No.TABLE 4/TABLE 3/TABLE 2/TABLE 1 = 4/3/2/1
TAX RATE : 0.0000 - 99.9999CYCLE : 0 - 9999INITIAL TAX : 0 - 999LOWER TAX LIMIT : 0 - 99999BREAK POINT : 0 - 99999
MRS = NO TAX
4. Character assignment method
∼ Using the alphabet assignment method ∼
Programming key layout
Using the ten key of the ECR
Note: The 00 key is used to enter each 3 digit alpha code.
Examples
“ A (Shift-2) “ A = “ is set
(DC) “ A = A (double character code) is set
(Shift) “ A = a (lowercase letter) is set
Once the (Shift) key is pressed, it stays down until it is pressedagain.
XXXXXX
HHMM
DATA
TIME
#
XXXXXX@/FORAB @/FOR
Declaration of TAX TAX rate
XXX@/FORXXXX @/FOR
Initial TAXCycle
XXXXX@/FORXXXXX @/FOR
Break pointLower TAX limit
CA/AT
TAX
@/FOF SBTLPush alphabet
Repeat
:
+
ZWRMHC
YVQLGB
XUPKFA
SNID
TOJE
?
(BS)(DC)
(Space)1 2 3
4 5 6
7 8 9
O
< >
;
-
#
@
=
?
)
%$
/
.
&
!
BACKSpace
( )< ( )<
( )
( ) ( )( )
( ) ( )- §
æ
Æ
£Pt
(Shift-2) (Shift)
ø ç
Φ
( ) : Function key
(DC) : Double character code entry key (One-shot)(Shift) : Character shift key (Stay-down)(Shift-2) : Mark key (One-shot)(BS) : Back space key
@/FOR 00XXX
3 digitsSBTL
Repeat
<Character Code Table for text programming>
CODE CHARACTER001 à002 â003 ê004 î005 ì006 í007 ô008 ó009 û010 ú011 œ012 ü013 ú014 ö015 ó016 Λ017 Ψ018 Γ019 ..
020 Ω021 ∆022 Θ023 Ξ024 Π025 Σ026 Υ027 Φ028 Ü029 Ú030 Ö031 Ó032 (Space)033 !034 "035 #036 $037 %038 &039 ’040 (041 )042043 + 044 , 045 –046 .047 /048 0049 1
CODE CHARACTER050 2051 3052 4053 5054 6055 7056 8057 9058 :059 ;060 <061 =062 >063 ?064 @065 A066 B067 C068 D069 E070 F071 G072 H073 I074 J075 K076 L077 M078 N079 O080 P081 Q082 R083 S084 T085 U086 V087 W088 X089 Y090 Z091 Ä092 Ö093 Ü094 ^ 095 _096097 a098 b
CODE CHARACTER099 c100 d101 e102 f103 g104 h105 i106 j107 k108 l109 m110 n111 o112 p113 q114 r115 s116 t117 u118 v119 w120 x121 y122 z123 124 |125 126 ß127128 !!129 1
130 2
131 3
132 4
133 1⁄2134 FT
135 ←136 →137138139140141 F
142 T
143 ↓144 ç145 O
146 ¿147 Ù
CODE CHARACTER148 à149 Æ150 φ151 Å152 ¤153 é154 è155 Pt156 ¡157 Ñ158 ò159 £160 ¥161162 163 164165 .
166 T 1
167 T 2
168 T 3
169 T 4
170 1 2
171 1 3
172 1 4
173 2 3
174 2 4
175 3 4
176177 Á178 Í179180 A181 a182 E183 e184 I185 i186 U187 u188
189
190191 Š192193194195
196
CODE CHARACTER
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211 š
212
213
214
215
216
217
218 ′219
220221222223224 *
225 §226 ∅227 ^ 228 ↑229 ]230 [
231
232 ä233 ö234 ü235 æ236 å237 É238 ñ
253 DC
(DC) : Double Code: ECR Control Character (Not used for text)
Fig. 7-2
CHAPTER 3. OP X/Z, X1/Z1,X2/Z2 MODE
The following categories of reports can be printed by the ECR.
OP X/Z reports: These reports are taken by operators in order toreport their own sales data.
XI/Z1 reports: These reports are taken by the supervisor or man-ager in order to check and report daily sales totalsat that point.
X2/Z2 reports: These reports are taken by the owner or managerin order to check and report periodic (weekly ormonthly) totals.
MGR/Flash-read: These reports are taken by the owner or managerin order to check and display daily sales totals atthat point.
To print reports, use the following key entry sequence
MODE *1
OP X/Z X1/Z1 X2/Z2 JOB# or KEY DATA FOR READING
REPORT NAME X Z X1 Z1 X2 Z2 *3 NOTE
GENERAL 00 ---
UPC (All) 09 ---
(Pick up) 09 PICK UP *4
UPC BY DEPT. 01 DEPT CODE
UPC ZERO SALES (All) 07 ---
(By DEPT.) 07 DEPT CODE
DEPT./GROUP 10 ---
IND. GROUP 12 GROUP No.
GROUP TOTAL 13 ---
PLU BY RANGE 20 PLU CODE *2
PLU BY DEPT. 21 DEPT CODE
PLU ZERO SALES (All) 27 ---
(By DEPT.) 27 DEPT CODE
PLU PRICE CATEGORY 29 PRICE *2
TRANSACTION 30 ---
CID 31 ---
ALL CASHIER 50 ---
IND. CASHIER 51 ---
HOURLY (All) 60 ---
(Range) 60 TIME *2
DAILY NET 70 ---
PBLU 80 PBLU CODE *2
PBLU BY CASHIER 81
STACKED REPORT 90 ---
DEPT. SALES (Frash-read) DEPTn --- *5
CID (Frash-read) [@/FOR] --- *5
DAILY MET SALES (Frash-read) [SBTL] --- *5
NON-ACCESSED UPC 105 ---
DELETE OF NON-ACCESSED UPC 105(*) ---
105(*) PICK UP *4
(*) At this operation, the non-accessed UPCs data are printed anddeleted.
To stop the printing reports:The printing of all reports can be stopped by the following operation.
Set the mode switch to "MGR" to cancel.
Note) When the printing is stopped, the consecutive number or Zcounter doesn’t return to the original value.For Z reports, Memory is not reset when canceled.
*1 X1: Daily X reportX2: Periodic X report
Z1: Daily Z reportZ2: Periodic Z report
*2 The time interval range and PLU code range can be specified byentering the start and end numbers according to the followingprocedure. When specifying a single time interval or PLU code,the start number has only to be entered.
*3 When 2 is entered in the third digit of a job code, periodic reportsare printed.
Example: Daily general report; job code 100Periodic general report; job code 200
JOB# @/FOR CA/AT
Reading
Resetting
Range is required
All
Start No. End No.@/FORXXXXXX XXXXXX
*4 (Pick-up reports from UPC utems)
Those reports asterisked (*4) in the above list can pick up some UPCdata which you very want to watch from the UPC file.
*5 Reading display only
KEY CL (Display amount) (Display initialize)
KEY DEPT = DEPTn keyCID = @/For keyDaily Net = ST key
• An individual report is printed on the receipt and journal when theCA/AT key is pressed.
• Pressing the decimal point key just after the entry of a job codeclears the corresponding data in the ECR. (Z report)(When printing those reports for which no Z reports can be taken,the decimal point key cannot be pressed after the entry of a jobcode.)
• When the decimal point key is not pressed after the entry of a jobcode, the corresponding data is held in the ECR. (X report)
XXXXXXXXXXXXX
Pick up (to the number of records in Pick-up file)
EAN code
(Scanning);Previous UPC codes picked up
;All UPC data
@/FOR CA/AT
@/FOR CA/AT
@/FOR CA/AT
COPYRIGHT 2000 BY SHARP CORPORATIONAll rights reserved.Printed in Japan.
No part of this publication may be reproduced,
stored in a retrieval system, or transmitted,in any form or by any means,
electronic, mechanical, photocopying, recording, or otherwise,
without prior written permission of the publisher.
SHARP CORPORATIONInformation Systems GroupQuality & Reliability Control CenterYamatokoriyama, Nara 639-1103, Japan
2000 December Printed in Japan