MODEL 10SX T/S - SPECIFICATIONliterature.puertoricosupplier.com/067/UW66310.pdf · MODEL 10SX T/S -...
Transcript of MODEL 10SX T/S - SPECIFICATIONliterature.puertoricosupplier.com/067/UW66310.pdf · MODEL 10SX T/S -...
MODEL 10SX T/S - SPECIFICATION
1.0 General SpecificationsTM There will be furnished one (1) only Grind Hog Model 10SX T/S Comminutor as manufactured by G.E.T.
Industries, Inc. Rotation shall be in a clockwise direction.
1.1 Design CriteriaThe comminutor shall be designed to handle the flows indicated below, within the head loss noted.
3a) hydraulic capacity 1.2 MGD (4500m /day)b) satisfactory operation shall occur under conditions of zero flowc) head loss at peak flow shall not exceed 10 inches (250)d) design shall be such that the flow enters the size reduction and screening device horizontally and exits
vertically downward to facilitate the flushing of solids
1.2 Cover PlateShall be:a) of heavy-duty construction and of high quality cast ironb) fitted with 4 position lock down arrangement, and 2 alignment holes for repositioning following servicec) located on, and positioned by wall mounted supports allowing for ease of removal for inspection
and maintenance.
1.3 Rotating Drum Screena) heavy-duty Cast Ductile Iron ASTM 536, grade 60-45-18
1.4 Cutting Elementsa) replaceable shear bars constructed of high-quality A2 tool-steel shall be attached to the rotating drum. Each
shear bar shall be machined from solid bar stock, surface ground to establish exact tolerancesb) the stationary cutting bar, shall be of high-quality 01 tool steel hardened to a minimum of 56 Rockwell C, and
shall be reversible, allowing for four (4) sets of cutting edges prior to sharpening or replacementc) all submerged fasteners shall be of stainless steel
1.5 MotorSubmersible, Explosion-proof 1 Hp. (.746 kw), 1750 RPM ______ volt, 3 phase, 60 HZ, rated for continuous-in-air or submerged in sewage service. Power control cable of 25 ft (7.6 m) included. Class 1, Group C and D, Division 1 Hazardous locations. The motor shall feature:
· Frame - rugged cast iron ASTM type A-48, class 30· Hardware - 316 stainless steel· Stator Insulation - specially treated class "F" and "H" non-hydroscopic insulation with multiple dips and
brakes. Phase insulation included for inverter duty· Rotor - die cast aluminum, dynamically balanced. Exceeds NEMA limits per MGI - 12.06· Shaft - high strength 416 stainless steel· Bearings - specially adapted for vertical assembly. Both upper and lower bearings are pre-packed and
sealed for life with special high temperature grease· Cable Entry System - epoxy sealed butt spliced connect for non-wicking cable entry design· Moisture System - two wire /two probe monitoring system constantly monitors oil chamber and stator
housing for moisture· Seals - tandem (dual) shaft steal system working independent of each other. Designed to withstand 100 PSI
at all seal locations
·
G.E.T. Industries Inc.Toll Free: (877) 213-7418
E-mail: [email protected] 6 Web: www.grindhog.com
MODEL 10SX T/S - SPECIFICATION cont’d...
1.6 Drive Arrangementa) the motor shall be close-coupled to a speed reducer drive, a heavy duty planetary gear of the totally
enclosed non-vented type suitable for total submergence during emergenciesb) double seals on the output shaft shall ensure flood-proof operation through a reduction ratio of 35:1c) the cycloidal reducer shall be capable of withstanding shock loads to 500% of its mechanical rating of
4.27 Hp. and be warranted for two (2) yearsd) the drive shall have a minimum full load efficiency of 90% and be pre-lubricated with grease, requiring routine
maintenance every 500 to 1,000 hours
1.7 “Toilet Seat” Channel Mounting SystemShall consist of a box-style structure dimensioned to suit the existing channel, supported by the channel walls; fabrication shall be 304 stainless steel.
G.E.T. Industries Inc.Toll Free: (877) 213-7418
E-mail: [email protected] 6 Web: www.grindhog.com
HYDRAULIC DATA SHEETIN-CHANNEL MODEL 10SX T/S
HYDRAULIC PERFORMANCE CURVE
.1 .2 .4 .6 1.0 2 4 5Flow Rate Q - Million U.S. Gallons Per Day
5
10
15
20
25
50
75
100
125.4 .8 1.6 2.4 3.2 4.0 6 8 12 16
3Flow Rate Q - Cubic Meters per Day x 10
50
40
30
20
15
10
8
6
4
2
Liq
uid
Le
vel D
iffe
ren
tial
Dh
= h
- h
In
che
s1
2
Liq
uid
Le
ve
l Diff
ere
ntia
l D
h =
h -
h C
en
time
ters
12
h = level in intake1
h = level in outlet2
Dh = head loss across drum (h -h )1 2
h = 0 for free discharge2
h =02 1 2 64 9
Drum submerged. Contnuous operation above this line is not recommended in systems where surface debris present.
MODEL 10T/S
.8
8
FLOWÙ×H1DATUMæ DISCHARGE H2×
×
@
H=H +H1 2
æDATUM
3Capacity 0-1.2 MGD (US) 0-4500 m /day
Drum Diam. 9.4 in 23.9 cm2 2Inlet Area 97 in 625.8 cm2 2Outlet Area 45 in 290.3 cm
Slot Width 0.470 in 12 mm
GENERAL DATA
G.E.T. Industries Inc.Toll Free: (877) 213-7418
E-mail: [email protected] 6 Web: www.grindhog.com
IN-CHANNEL MODEL 10SX T/S cont’d...
· HIGHEST OVERLOAD CAPACITY FOR FREQUENT STOP-START AND SEVERE REVERSING
· SMOOTH, SILENT OPERATION · EXCEPTIONAL LIFETorque transmitting parts roll, don’t grind. There is no sliding friction, so output torque/input horsepower efficiency approaches 95%
6000 SERIES
STATIONARY CUTTING BAR
·REVERSE-SPARE STANDARD EQUIPMENT
·A2 HIGH QUALITY TOOL STEEL·HIGH RESITANCE TO WEAR
CAST DUCTILE IRONSEWAGE SCREEN· LONG LIFE UNDERABRASIVE CONDITIONS
ROTATING SHEAR BARASSEMBLY
· MACHINED FROM SOLID BARSTOCK
· PRECISE TOLERANCES MAINTAINED
SUBMERGED FASTENERSOF STAINLESS STEEL
HEAVY DUTY CAST IRONCONSTRUCTION
G.E.T. Industries Inc.Toll Free: (877) 213-7418
E-mail: [email protected] 6 Web: www.grindhog.com
DESIGN FEATURES
DIMENSIONAL & MECHANICAL DETAILDIMENSIONAL & MECHANICAL DETAIL
W D
W
C
RETROFIT ALTERNATIVE
HORI ONTAL FLOW
PROJECT:
ANTICIPATED PEAK FLOW: ____
EXISTING CHANNEL
Width (w): ____Depth (d): ____Underdrain Clearance (c): ____
MOTOR REQUIREMENTS
Power: ____ / ____ / ____
Enclosure: _____________
“TOILET SEAT BOX STYLE”DROP IN REPLACEMENT
Toilet Seat Box Style Channel Template3 2025
Fabricated of304 Stainless Steelto suit existingchannel dimensions
Replaceablewear ring forextended life
Supported fromabove on thechannel wallseliminating therequirement forany submergedanchorage REPLACING
Worthington InfilcoDegrement
Franklin Miller Muffin Monster
Clow-Barminutor
......Among Others
Customized to suit each application
G.E.T. INDUSTRIES INC.Toll Free: (877) 213-7418
E-mail: [email protected] 6 Web: www.grindhog.com
16ASX T/S Custom Fabricated Basin& 16ASX T/S
Ready for Shipment
Custom Fabricated Basin
Original Worthington 15-5
ORIGINAL CHANNEL
PROPOSED CHANGES