micro FieldCommanders

8
V2009-a Field- Commander inside ! ® CER products • FieldCommander micro FieldCommander Embedded Servers FCDomus domotica software

description

Small and smart embedded devices for linking I/O (digital or analog input or output) to your network (ethernet LAN)

Transcript of micro FieldCommanders

Page 1: micro FieldCommanders

V2009-a

Field-

Commander

inside !

®

CER products

• FieldCommander

• micro FieldCommander

• Embedded Servers

• FCDomus domotica software

Page 2: micro FieldCommanders

V2009-a

Network I/O module uFC 9015; 7ch RTD inputWebbased smart ethernet Measurement & Control

Highlights

Link this I/O module to your computernetwork for measurement &control.To install this module support for several software environments isincluded and for easy management a softwaretool is included.Now you extend your network with reliable I/O in a short time withlow costs.

This I/O module can be easily combined with a webcontroller like aFieldCommander or a PC. The module can be operated remotely.

• Analog Input:– Input channels: 7– Input type

• 2 or 3 wire RTD• Pt100: -50 ~15C; 0~1000C; 0~200C; -200~200C• Pt1000: -40 ~ 160C• Ni518: -80~100C; 0~100C

– Sampling: 10s/sec.– Resolution: 16 bit– Volt protection:+/- 35VDC

Analog RTD input: 7x

Micro-

FieldCommander

uFC9015

Copyright © 2010 CER International bv. All rights reserved. Specifications may change without notice. CER®, FieldCommander®, FCDomus® and FCEnterCom® are registered trademarks.

uFC 9015

Network support

• Ethernet; 10/100 Mbps

• UTP RJ45 connection

• Modbus/TCP; TCP/IP; UDP

Analog Input

• Support analog RTD inputs

Hardware

• Based on the low cost e-CER

platform with IP-stack.

Power supply: 10-30 VDC

Power consumption: ca. 2,4W

• DIN-rail clips included

Software tools

• DLL, ActiveX, VB, Delphi

• Can be linked with a Field-

Commander webcontroller.

Product options.

• Powersupply

CER International bvPostbus 258NL-4700 AG RoosendaalTel.: +31(0)165-557417Fax: +31(0)[email protected]

Order info

uFC9015 Micro-FieldCommander; 7x RTD analog input.FCPwr10 Powersupply (euro)FCPwr10UK Powersupply (UK)

Page 3: micro FieldCommanders

V2009-a

Network I/O module uFC 9017; 8ch Analog inputWebbased smart ethernet Measurement & Control

Order info

uFC9017 Micro-FieldCommander; 8x analog V/I input.FCPwr10 Powersupply (euro)FCPwr10UK Powersupply (UK)

•Analog Input:– Input channels: 8– Input type

• differential• thermocouple+/V ; +/- mV; +/- mA• +/- 150mV; +/- 500V; +/- 1V; +/- 10V• 0-20mA; 4-20mA

– Sampling: 10s/sec.– Resolution: 16 bit– Volt protection:+/- 35VDC

• Digital Output:– Channels: 2– Sink type: Open collector to 30V, 100mA(maximum load)

Copyright © 2010 CER International bv. All rights reserved. Specifications may change without notice. CER®, FieldCommander®, FCDomus® and FCEnterCom® are registered trademarks.

uFC 9017

CER International bvPostbus 258NL-4700 AG RoosendaalTel.: +31(0)165-557417Fax: +31(0)[email protected]

Analog V/I input: 8x ; DO: 2x

Micro-

FieldCommander

uFC9017

Network support

• Ethernet; 10/100 Mbps

• UTP RJ45 connection

• Modbus/TCP; TCP/IP; UDP

Analog Input

• Support analog V/I inputs

Digital Output

• Support digital outputs

Hardware

• Based on the low cost e-CER

platform with IP-stack.

Power supply: 10-30 VDC

Power consumption: ca. 2,4W

• DIN-rail clips included

Software tools

• DLL, ActiveX, VB, Delphi

• Can be linked with a Field-

Commander webcontroller.

Product options.

• Powersupply

Highlights

Link this I/O module to your computernetwork for measurement &control.To install this module support for several software environments isincluded and for easy management a softwaretool is included.Now you extend your network with reliable I/O in a short time withlow costs.

This I/O module can be easily combined with a webcontroller like aFieldCommander or a PC. The module can be operated remotely.

Page 4: micro FieldCommanders

V2009-a

Network I/O module uFC 9019; 8ch Thermocouple inWebbased smart ethernet Measurement & Control

Order info

uFC9019 Micro-FieldCommander; 8x Thermocouple input.FCPwr10 Powersupply (euro)FCPwr10UK Powersupply (UK)

•Analog Input:– Input channels: 8– Input type

• differential• thermocouple• J-type• K-type: 0~1370C• T-type: -100 ~ 400C• E/R/S/B-type

– Sampling: 10s/sec.– Resolution: 16 bit– Volt protection:+/- 35VDC

• Digital Output:– Channels: 2– Sink type: Open collector to 30V, 100mA(maximum load)

Copyright © 2010 CER International bv. All rights reserved. Specifications may change without notice. CER®, FieldCommander®, FCDomus® and FCEnterCom® are registered trademarks.

uFC 9019

CER International bvPostbus 258NL-4700 AG RoosendaalTel.: +31(0)165-557417Fax: +31(0)[email protected]

Anal.Thermocouple inp.: 8x ; DO: 2x

Micro-

FieldCommander

uFC9019

Network support

• Ethernet; 10/100 Mbps

• UTP RJ45 connection

• Modbus/TCP; TCP/IP; UDP

Analog Input

• Support analog thermoc. inputs

Digital Output

• Support digital outputs

Hardware

• Based on the low cost e-CER

platform with IP-stack.

Power supply: 10-30 VDC

Power consumption: ca. 2,4W

• DIN-rail clips included

Software tools

• DLL, ActiveX, VB, Delphi

• Can be linked with a Field-

Commander webcontroller.

Product options.

• Powersupply

Highlights

Link this I/O module to your computernetwork for measurement &control.To install this module support for several software environments isincluded and for easy management a softwaretool is included.Now you extend your network with reliable I/O in a short time withlow costs.

This I/O module can be easily combined with a webcontroller like aFieldCommander or a PC. The module can be operated remotely.

Page 5: micro FieldCommanders

V2009-a

Network I/O module uFC 9050; 18ch digital I/OWebbased smart ethernet Measurement & Control

Order info

uFC9050 Micro-FieldCommander; 18ch digital I/O.FCPwr10 Powersupply (euro)FCPwr10UK Powersupply (UK)

•Digital Input:– Input channels: 12– Input type

• Dry contact– logic level 0: Close to ground– logic level 1: Open

• Wet contact:– logic level 0: 0~3V– logic level 1: 10~30V

– Counter/Frequency: Each channel support 3KHz input– Isolation: Fully photo-isolation 2,000Vrms

• Digital Output:– Channels: 6– Sink type: Open collector to 30V, 100mA(maximum load)– Pulse output– Isolation: Fully photo-isolation 2,000Vrms

Copyright © 2010 CER International bv. All rights reserved. Specifications may change without notice. CER®, FieldCommander®, FCDomus® and FCEnterCom® are registered trademarks.

uFC 9050

CER International bvPostbus 258NL-4700 AG RoosendaalTel.: +31(0)165-557417Fax: +31(0)[email protected]

Digital In: 12x ; Digital Out: 6x

Micro-

FieldCommander

uFC9050

Network support

• Ethernet; 10/100 Mbps

• UTP RJ45 connection

• Modbus/TCP; TCP/IP; UDP

Digital Input

• Support dry/wet contact input

Support counter/frequency input

Digital Output

• Support digital outputs

Hardware

• Based on the low cost e-CER

platform with IP-stack.

Power supply: 10-30 VDC

Power consumption: ca. 2,4W

• DIN-rail clips included

Software tools

• DLL, ActiveX, VB, Delphi

• Can be linked with a Field-

Commander webcontroller.

Product options.

• Powersupply

Highlights

Link this I/O module to your computernetwork for measurement &control.To install this module support for several software environments isincluded and for easy management a softwaretool is included.Now you extend your network with reliable I/O in a short time withlow costs.

This I/O module can be easily combined with a webcontroller like aFieldCommander or a PC. The module can be operated remotely.

Page 6: micro FieldCommanders

V2009-a

Network I/O module uFC 9051; 14ch digital I/OWebbased smart ethernet Measurement & Control

Order info

uFC9051 Micro-FieldCommander; 14ch digital I/O.FCPwr10 Powersupply (euro)FCPwr10UK Powersupply (UK)

•Digital Input:– Input channels: 12– Input type

• Dry contact– logic level 0: Close to ground– logic level 1: Open

• Wet contact:– logic level 0: 0~3V– logic level 1: 10~30V

– Counter/Frequency: Each channel support 3KHz input– Isolation: Fully photo-isolation 2,000Vrms

• Digital Output:– Channels: 2– Sink type: Open collector to 30V, 100mA(maximum load)– Pulse output– Isolation: Fully photo-isolation 2,000Vrms

• Digital Counter Input:– Channels: 2

Copyright © 2010 CER International bv. All rights reserved. Specifications may change without notice. CER®, FieldCommander®, FCDomus® and FCEnterCom® are registered trademarks.

uFC 9051

CER International bvPostbus 258NL-4700 AG RoosendaalTel.: +31(0)165-557417Fax: +31(0)[email protected]

D.In: 12x ; D.Out: 2x; Counter In: 2x

Micro-

FieldCommander

uFC9051

Network support

• Ethernet; 10/100 Mbps

• UTP RJ45 connection

• Modbus/TCP; TCP/IP; UDP

Digital Input

• Support dry/wet contact input

Support counter/frequency input

Digital Output

• Support digital outputs

Hardware

• Based on the low cost e-CER

platform with IP-stack.

Power supply: 10-30 VDC

Power consumption: ca. 2,4W

• DIN-rail clips included

Software tools

• DLL, ActiveX, VB, Delphi

• Can be linked with a Field-

Commander webcontroller.

Product options.

• Powersupply

Highlights

Link this I/O module to your computernetwork for measurement &control.To install this module support for several software environments isincluded and for easy management a softwaretool is included.Now you extend your network with reliable I/O in a short time withlow costs.

This I/O module can be easily combined with a webcontroller like aFieldCommander or a PC. The module can be operated remotely.

Page 7: micro FieldCommanders

V2009-a

Network I/O module uFC 9052; 16ch digital I/OWebbased smart ethernet Measurement & Control

Order info

uFC9052 Micro-FieldCommander; 16ch digital I/O.FCPwr10 Powersupply (euro)FCPwr10UK Powersupply (UK)

•Digital Input:– Input channels: 8– Input type

• Dry contact– logic level 0: Close to ground– logic level 1: Open

• Wet contact:– logic level 0: 0~3V– logic level 1: 10~30V

– Counter/Frequency: Each channel support 3KHz input– Isolation: Fully photo-isolation 2,000Vrms

• Digital Output:– Channels: 8– Sink type: Open Collector upto 30V, 1000mA(max)– Isolation: 2,000Vrms

Copyright © 2010 CER International bv. All rights reserved. Specifications may change without notice. CER®, FieldCommander®, FCDomus® and FCEnterCom® are registered trademarks.

uFC 9052

CER International bvPostbus 258NL-4700 AG RoosendaalTel.: +31(0)165-557417Fax: +31(0)[email protected]

Digital In: 8x ; Digital Out: 8x;

Micro-

FieldCommander

uFC9052

Network support

• Ethernet; 10/100 Mbps

• UTP RJ45 connection

• Modbus/TCP; TCP/IP; UDP

Digital Input

• Support dry/wet contact input

Support counter/frequency input

Digital Output

• Support digital outputs

Hardware

• Based on the low cost e-CER

platform with IP-stack.

Power supply: 10-30 VDC

Power consumption: ca. 2,4W

• DIN-rail clips included

Software tools

• DLL, ActiveX, VB, Delphi

• Can be linked with a Field-

Commander webcontroller.

Product options.

• Powersupply

Highlights

Link this I/O module to your computernetwork for measurement &control.To install this module support for several software environments isincluded and for easy management a softwaretool is included.Now you extend your network with reliable I/O in a short time withlow costs.

This I/O module can be easily combined with a webcontroller like aFieldCommander or a PC. The module can be operated remotely.

Page 8: micro FieldCommanders

V2009-a

CER

Order info: contact your local CER representative:

Copyright © 2010 CER International bv. All rights reserved. Specifications may change without notice. CER®, FieldCommander®, FCDomus® and FCEnterCom® are registered trademarks.

CER International bvPostbus 258NL-4700 AG RoosendaalTel.: +31(0)165-557417Fax: +31(0)[email protected]

Development

The CER development team is capable to integrateyour special requirements..

Manufacturer

CER can brand label the products for you.

.