to.

the fuselage. Doing so can cause EXTREME BODILY HARM if any hand or body part comes into contact with the fast spinning propeller. ·All minors should fly under the supervision of an adult or guardian.

Wingspan: 41.5 Inches Motor: 2212/6 or Higher Brusless Outrunner ESC: 30 AMP or Higher Brushless ESC

Prop: APC 6x4Battery: 2100mAH 3S (30C or Higher Lipo)

Servos:

Core Fan Fold Foam to build this plane too.Board. It should be possible to use Depron Foam or Blue plane was originally designed to be built from Foam materials, motor, battery and electronics used. This

: Weight and top speed may vary depending on Note

: 65mph to 90+ (Depending on Power System)

(Contact MESA rcFoamFighters at: mesarcfoamfighters@gmail.com)information or instructions.be Sold, or Altered to remove theMESA rcFoamFighters contact at local copy houses for personal use only. This plan may not MESA rcFoamFighters grants permission for this plan to be copied

Top Speed: 8.5 Inches from Nose of of plane.Center of Gravity

: 24 OuncesWeight: 19.5 InchesLength

(2.4ghz preferred) Any 4-channel or better Radio and Reciever:

2 Metal Gear

Disclaimer (Please Read)·This is a design template for a high performance, high speed RC aircraft. This plane should only be built and flown by experienced pilots with adequate skill to fly fast, maneuverable planes. ·DO NOT fly this plane where it can endanger people, livestock or property. ·ANY PERSONS DECIDING TO BUILD AND FLY THIS PLANE DOES SO AT HIS/HER OWN RISK AND LIABILITY. RCFOAMFIGHTERS ASSUMES NO RESPONSIBILITY FOR THE PERFORMANCE OF THIS PLANE. ·This plane should only be launched via the side launch method. Do not attempt to launch from the top or bottom of

Motor mount without brackets, you can alter this to fit your power systemif need

SolidWorks Student LicenseAcademic Use Only

PRINT ALL TEMPLATE SHEETS. CUT AND ASSEMBLE AS SHOWN INSTRUCTIONS:

BELOW. USE SCOTCH TAPE TO SECURE SHEETS TOGETHER.

(RC Model Airplane Construction Plans)MESA rcFoamFighters Team

MFB-2 Basic PlanTemplate(Design by Ken Tanpinco Revisions by Cody Lightbody)

(CAD Drawing by Jake Marshall)(Template Rev 1.0 - Copyright MESA rcFoam Fighters)

SolidWorks Student LicenseAcademic Use Only

(Template Rev 1.0 - Copyright MESA rcFoam Fighters)(CAD Drawing by Jake Marshall)

(Design by Ken Tanpinco Revisions by Cody Lightbody)

(RC Model Airplane Construction Plans)MESA rcFoamFighters Team

MFB-2 KFM4 and Parts Placement

NOTE: KFM4 Airfoil Placement is 50% of Main Wing, Include Elevrons.

Center of Gravity 8 1/2 inches

This Includes the KFM4From Nose of Plane

SolidWorks Student LicenseAcademic Use Only

(Contact MESArcFF at: mesarcfoamfighters@gmail.com)(All proceeds go to the students of MESA rcFoam Fighters)

CENTER STABILIZER

LEFT STABILIZER

RIGHT STABILIZER

MESA rcFoam FightersMFB-2 Basic Template(Design by Ken Tanpinco - 2010 )(Revised by Cody Lightbody - November 2011 Rev 1.0 )(CAD Drawing by Jake Marshall and Cody Lightbody - November11)(Basic Template release 1.0 - Copyright MESA rcFoam Fighters)

Copyright MESA rcFoam Fighters(MFB-2)

SolidWorks Student LicenseAcademic Use Only

SolidWorks Student LicenseAcademic Use Only

CENTER SUPPORT BOTTOM PIECE

SolidWorks Student LicenseAcademic Use Only

MOTOR BRACKET

MOTOR BRACKET

Motor Bracket

SolidWorks Student LicenseAcademic Use Only

SolidWorks Student LicenseAcademic Use Only

Cut Seen Here in the(Isometric View )

Double 45DEG Bevel Then Fold on ...

SolidWorks Student LicenseAcademic Use Only

SolidWorks Student LicenseAcademic Use Only

NOTE: Drag Spacer Placement Seen HereNOTE: Drag Spacer Placement Seen Here

SolidWorks Student LicenseAcademic Use Only

SolidWorks Student LicenseAcademic Use Only

Cut Notches For Right Stabilizers On This Side

SolidWorks Student LicenseAcademic Use Only

centerline, fold over main wing piece.

NOTE: Make a cut down the center of the airfoil, bevel both sides along

SolidWorks Student LicenseAcademic Use Only

centerline, fold over main wing piece.

NOTE: Make a cut down the center of the airfoil, bevel both sides along

SolidWorks Student LicenseAcademic Use Only

Battery Cut Out

SPEED.

ANGLE.

PIECES. THESE ARE

RECOMMENDED

NOTE: DRAG SUPPORT

SET AT THE

NOTE: INCREASING ANGLE = DECREASE IN SPEED. DECREASING IN ANGLE = INCREASE IN

Battery Cut Out

SolidWorks Student LicenseAcademic Use Only

Prop Cut Out

Battery Cut Out

Battery Cut Out

Prop Cut Out

SolidWorks Student LicenseAcademic Use Only

SolidWorks Student LicenseAcademic Use Only

SolidWorks Student LicenseAcademic Use Only

SolidWorks Student LicenseAcademic Use Only

SETUP ELEMENTS.

NOTE: THERE IS NO EXACT PLACEMENT OF AIRDUCTS. POSITION THEM TO FIT POWER

SolidWorks Student LicenseAcademic Use Only

SolidWorks Student LicenseAcademic Use Only

Cut Notches For Right Stabilizers On This Side

SolidWorks Student LicenseAcademic Use Only

SolidWorks Student LicenseAcademic Use Only

CENTER SUPPORT TOP PIECE

Cut Notches For Motor Bracket On This SIde

SolidWorks Student LicenseAcademic Use Only

SolidWorks Student LicenseAcademic Use Only

FUSELAGE TOP PIECE

FUSELAGE TOP PIECE

FUSELAGE TOP PIECE

FUSELAGE TOP PIECE

NOTE: Make small cuts into paper of foam board to achieve desired curve

of fuselage.

SolidWorks Student LicenseAcademic Use Only

SolidWorks Student LicenseAcademic Use Only