Mateo™ Single Lever Pull Out Kitchen Faucet...countertop to remove any debris, plumber’s putty,...
Transcript of Mateo™ Single Lever Pull Out Kitchen Faucet...countertop to remove any debris, plumber’s putty,...
INSTALLATION MANUAL
KPF-2610
Mateo™ Single Lever Pull Out Kitchen Faucet
www.kraususa.com I toll free: 1.800.775.0703 I © 2014-2015 Kraus USA Inc. I REV. August 26, 2015
1
Thank you for purchasing Kraus
We would like to take this opportunity to thank you for your business with Kraus USA. It is our sincere hope that you are completely satisfied with your experience. We welcome any questions or comments you may have, and will be glad to assist you in the future.
For more information about Kraus products, please visit our website at:
www.kraususa.com
Please register your new Kraus product at the following web address in order to activate the warranty and receive the full benefit of customer support:
www.kraususa.com/registration
Sincerely,
Kraus Customer Service Department
2
Prior to Installation:
• Make sure you have all necessary parts by checking the diagram and parts list. If
any part is missing or damaged, please contact Kraus Customer Service at 800-
775-0703 for a replacement
• Turn off the hot and cold water supply at the angle stops and turn on the old
faucet to release any built up pressure. Remove existing faucet. Clean sink or
countertop to remove any debris, plumber’s putty, or silicone
• Place bucket under angle stops. Turn on to flush any debris prior to installing new
plumbing. Shut off angle stops
• Pre-drilled hole size requirement: 1-3/8” (min) – 1-1/2” (max)
• Max countertop thickness without deck plate: 1-1/2”
• Max countertop thickness with deck plate: 1”
Tools you will need:
Adjustable Wrench Safety Goggles Bucket Silicone Sealant
6 5/8”
5 4/5”
3/8”(10mm)
7/8”
19.7º (22mm)
8 5/16”
1 1/4-18UNF-2A
(21mm)10 1/8”
(257mm)
1 3/8”(35mm)
3 3/4”
(168mm)
(147.3mm)
(96mm)
∅ 1 3/4”(∅ 45mm)
∅ 1 15/16”(∅ 50mm)
9/16”-18UNEF
27m
m ~
41.
3mm
1 1/
16”
~ 1
5/8”
∅ 1 15/16”(∅ 50mm)
12 7/16”(316mm)
1 5/8”(42.5 mm Max)
7A
8B8C
8D
8A
7A
8B8C
8D
8A
Without deck plate:
With deck plate:
1/16” (1mm) min. 1-1/2” (38 mm) max.
Ø 1-3/8” (35 mm) min.Ø 1-1/2” (38 mm) max.
1/16” (1mm) min. 1” (25.4 mm) max.
Ø 1-3/8” (35 mm) min.Ø 1-1/2” (38 mm) max.
1
2
Designated Mark
Hot
Upward
Blac
k
Cold
1A 1B
2 3 4
5 67
GG
E E F
G
G
G
G
F
F
F
E
EH
E
EA
A
I
B
J
D
D
C D
G
Half Moon Locking NutsHalf Moon Locking Nuts
Rubber Caps
Adjustable wrench Phillips screwdriver
Tools You Will Need
Hex wrench Silicone Sealant
A
I
D
JF
B
G
C
H
E
3
Adjustable wrench Phillips screwdriver
Tools You Will Need
Hex wrench Silicone Sealant
A
I
D
JF
B
G
C
H
E
Diagram and Parts List
A. Spray Head
B. Faucet Body
C. Deck & Putty Plate
D. Base
E. Spray Hose
F. Supply Hose
G. Hot & Cold Waterlines
H. Weight
I. Quick Connect
J. Hex Wrench Set
J1. 2mm
J2. 2.5mm
J3. 4mm
4
9/16-24UNEF(3/8” Compression)
Check Value
0.06
”~1.
5” m
ax(1
mm
~38.
1mm
) max
7.37
(187
mm
) 9.
75”
(247
mm
) 10
.5”
(266
mm
)
0.06
”~1”
max
(1m
m~2
5.4m
m) m
ax
0.31
”(8
.5m
m)
Ø1.94”(Ø50mm)
10.2”(258mm)
10.31”(262mm)
8.125”(207mm)
2.5”(63mm)
9º
9/16-24UNEF(3/8” Compression)
Check Value
0.06
”~1.
5” m
ax(1
mm
~38.
1mm
) max
7.37
(187
mm
) 9.
75”
(247
mm
) 10
.5”
(266
mm
)
0.06
”~1”
max
(1m
m~2
5.4m
m) m
ax
0.31
”(8
.5m
m)
Ø1.94”(Ø50mm)
10.2”(258mm)
10.31”(262mm)
8.125”(207mm)
2.5”(63mm)
9º
Faucet Dimensions
5
Step 1A: Install base without deck & putty plate
Insert base (D) into sink or countertop with “FR↑NT” facing forward. Tighten screws on base (D) with 4mm hex wrench (J)until base is secure on sink or countertop
Step 1B: Install base with deck & putty plate
Place a bead of clear silicone sealant (not included) around the edge of the putty plate (C). Secure deck & putty plate (C) on sink or countertop. Insert base (D) into hole of deck & putty plate (C) with “FR↑NT”facing forward. Tighten screws on base (D) with 4mm hexwrench (J) until base is secure on deck & putty plate (C)
Without deck plate:
With deck plate:
1/16” (1mm) min. 1-1/2” (38 mm) max.
Ø 1-3/8” (35 mm) min.Ø 1-1/2” (38 mm) max.
1/16” (1mm) min. 1” (25.4 mm) max.
Ø 1-3/8” (35 mm) min.Ø 1-1/2” (38 mm) max.
1
2
Designated Mark
Hot
Upward
Blac
k
Cold
1A 1B
2 3 4
5 67
GG
E E F
G
G
G
G
F
F
F
E
EH
E
EA
A
I
B
J
D
D
C D
G
Half Moon Locking NutsHalf Moon Locking Nuts
Rubber Caps
Without deck plate:
With deck plate:
1/16” (1mm) min. 1-1/2” (38 mm) max.
Ø 1-3/8” (35 mm) min.Ø 1-1/2” (38 mm) max.
1/16” (1mm) min. 1” (25.4 mm) max.
Ø 1-3/8” (35 mm) min.Ø 1-1/2” (38 mm) max.
1
2
Designated Mark
Hot
Upward
Blac
k
Cold
1A 1B
2 3 4
5 67
GG
E E F
G
G
G
G
F
F
F
E
EH
E
EA
A
I
B
J
D
D
C D
G
Half Moon Locking NutsHalf Moon Locking Nuts
Rubber Caps
Installer Tip: Rotate the two half-moon shaped locking nuts inward before inserting base (D) into deck plate (C)
Installer Tip: Rotate the two half-moon shaped locking nuts inward before inserting base (D) into sink or countertop
6
Step 2: Install faucet
Step 3: Secure faucet
Insert spray hose (E) into small hole of base (D). Insert hot & cold waterlines (G) and supplyhose (F), one by one, in large hole of base
Align arrow on faucet body (B) with arrow on base (D).Attach faucet body (B) to base(D). Secure faucet body (B) bytightening the set screw with2.5mm hex wrench (J)
Without deck plate:
With deck plate:
1/16” (1mm) min. 1-1/2” (38 mm) max.
Ø 1-3/8” (35 mm) min.Ø 1-1/2” (38 mm) max.
1/16” (1mm) min. 1” (25.4 mm) max.
Ø 1-3/8” (35 mm) min.Ø 1-1/2” (38 mm) max.
1
2
Designated Mark
Hot
Upward
Blac
kCold
1A 1B
2 3 4
5 67
GG
E E F
G
G
G
G
F
F
F
E
EH
E
EA
A
I
B
J
D
D
C D
G
Half Moon Locking NutsHalf Moon Locking Nuts
Rubber Caps
Without deck plate:
With deck plate:
1/16” (1mm) min. 1-1/2” (38 mm) max.
Ø 1-3/8” (35 mm) min.Ø 1-1/2” (38 mm) max.
1/16” (1mm) min. 1” (25.4 mm) max.
Ø 1-3/8” (35 mm) min.Ø 1-1/2” (38 mm) max.
1
2
Designated Mark
Hot
Upward
Blac
k
Cold
1A 1B
2 3 4
5 67
GG
E E F
G
G
G
G
F
F
F
E
EH
E
EA
A
I
B
J
D
D
C D
G
Half Moon Locking NutsHalf Moon Locking Nuts
Rubber Caps
Installer Tip: Please remove rubber caps from spray hose (E) and supply hose (F) prior to insertinginto base
Installer Tip: To remove Quick Connect (I), push housing upward, hold firmly, and pull downward
Installer Tip: Please loosen set screw from faucet body (B) prior to securing to base (D)
7
Step 4: Connect waterlines to main valve
Step 5: Connect quick connect
Thread hot & cold waterlines (G) onto angle stops. Tightenwith adjustable wrench untilsnug. Turn on the angle stopsand check for leaks (DO NOTTURN FAUCET ON)
Attach Quick Connect (I) withblack end onto spray hose (E)until you hear a click. Attach the other end onto the supply hose (F)
Without deck plate:
With deck plate:
1/16” (1mm) min. 1-1/2” (38 mm) max.
Ø 1-3/8” (35 mm) min.Ø 1-1/2” (38 mm) max.
1/16” (1mm) min. 1” (25.4 mm) max.
Ø 1-3/8” (35 mm) min.Ø 1-1/2” (38 mm) max.
1
2
Designated Mark
Hot
Upward
Blac
k
Cold
1A 1B
2 3 4
5 67
GG
E E F
G
G
G
G
F
F
F
E
EH
E
EA
A
I
B
J
D
D
C D
G
Half Moon Locking NutsHalf Moon Locking Nuts
Rubber Caps
Without deck plate:
With deck plate:
1/16” (1mm) min. 1-1/2” (38 mm) max.
Ø 1-3/8” (35 mm) min.Ø 1-1/2” (38 mm) max.
1/16” (1mm) min. 1” (25.4 mm) max.
Ø 1-3/8” (35 mm) min.Ø 1-1/2” (38 mm) max.
1
2
Designated Mark
Hot
Upward
Blac
k
Cold
1A 1B
2 3 4
5 67
GG
E E F
G
G
G
G
F
F
F
E
EH
E
EA
A
I
B
J
D
D
C D
G
Half Moon Locking NutsHalf Moon Locking Nuts
Rubber Caps
Installer Tip: Tug on the spray hose (E) moderately to ensure both connections are secure
8
Step6: Install weight
Step 7: Flush faucet
Attach weight (H) on the designated mark on the spray hose (E)
Remove spray head (A). Hold tip of spray hose (E). Turn faucet on for 1 minute to flush any debris. Reconnect spray head (A)
Without deck plate:
With deck plate:
1/16” (1mm) min. 1-1/2” (38 mm) max.
Ø 1-3/8” (35 mm) min.Ø 1-1/2” (38 mm) max.
1/16” (1mm) min. 1” (25.4 mm) max.
Ø 1-3/8” (35 mm) min.Ø 1-1/2” (38 mm) max.
1
2
Designated Mark
Hot
Upward
Blac
k
Cold
1A 1B
2 3 4
5 67
GG
E E F
G
G
G
G
F
F
F
E
EH
E
EA
A
I
B
J
D
D
C D
G
Half Moon Locking NutsHalf Moon Locking Nuts
Rubber Caps
Without deck plate:
With deck plate:
1/16” (1mm) min. 1-1/2” (38 mm) max.
Ø 1-3/8” (35 mm) min.Ø 1-1/2” (38 mm) max.
1/16” (1mm) min. 1” (25.4 mm) max.
Ø 1-3/8” (35 mm) min.Ø 1-1/2” (38 mm) max.
1
2
Designated Mark
Hot
Upward
Blac
k
Cold
1A 1B
2 3 4
5 67
GG
E E F
G
G
G
G
F
F
F
E
EH
E
EA
A
I
B
J
D
D
C D
G
Half Moon Locking NutsHalf Moon Locking Nuts
Rubber Caps
9
Replacement Part List
1 Metal Handle Assembly A662362-502 Trim Cap A103290-P3 Locking Nut A1042044 Ceramic Disc Cartridge A507348N5 Screw A0752096 Shank Assembly A0140917 Cover Plate & Putty Plate A66F489-T8 Hand Spray W/ Check valve A523827N-559 Hose Adapter A663123N10 Supply Hose A515103N11 Weight A50407112 Hex wrench (H2.5mm * 11mm L * 53mmL) A031217NI13 Hex Wrench(H2 * 17 mm L * 49 mm L) A031003NI14 Hex Wrench (H4 * 20 mm L * 70 mm L) A031011NI
1
2
3
4
5
8
11
10
12
13
14
9
6
7
1. Metal Assembly Handle
2. Cartridge Cover
3. Locking Nut
4. Cartridge
5. Set Screw
6. Base
7. Cover & Putty Plate
8. Spray Head
9. Quick Connect
10. Spray Hose
11. Weight
12. Hex Wrench 2.5mm
13. Hex Wrench 2mm
14. Hex Wrench 4mm
10
Trouble - Shooting If you have followed the instructions carefully and your faucet still does not work
properly, take the following corrective steps:
P R O B L E M C A U S E A C T I O N
Leakage under the handle
Locking nut (3) has come loose
Unscrew joystick from handle (1). Loosen set screw with a hex wrench (13). Remove metal handle (1). Unscrew cartridge cover (2) by hand only. Tighten locking nut (3) with an adjustable wrench
Leaking from spray hose
Quick Connect (9) may be installed incorrectly
Remove Quick Connect (9) from spray hose (10) and reinstall. Make sure you hear a click when you install it on the spray hose (10)
Water will not shut off completely
Cartridge (4) may need to be adjusted or replaced
Unscrew joystick from handle (1). Loosen set screw with a hex wrench (13). Remove metal handle (1). Unscrew cartridge cover (2) by hand only. Remove locking nut (3) with an adjustable wrench. Remove ceramic disc cartridge (4). Check for cracks
11
Trouble - Shooting If you have followed the instructions carefully and your faucet still does not work
properly, take the following corrective steps:
P R O B L E M C A U S E A C T I O N
Hose does not retract Weight (11) may be installed incorrectly
Readjust weight (11) on the hose (10). Make sure it is installed on the designated mark on the hose (11)
Low Flow Quick Connect (9) may be clogged with debris
Remove Quick Connect (9) from hoses. Soak in 50/50 solution of warm water and vinegar for 5 minutes, then reinstall
12
Care & Maintenance*To keep the product clean & shining, follow the steps below:
1. Rinse with clean water & dry with a soft cloth2. Do not clean with soaps, acid, polish, abrasives, or harsh cleaners3. Do not use cloth with a coarse surface4. Unscrew the aerator and clean when necessary
*This installation manual is subject to change without further notice.
1
10
279
10 3
1/32
”
Minimum distance 90mm
Less than 90mm
Cold Water
32 3
/32”
Ø35~Ø38
1
23
10
911
12 13
Hexagon Nut
HotWater
ColdWater
2 3
1
4576
8
45
67
8
Ø1 3/8”~Ø1 1/2”
815
1947 5/8”
Ø1 3/8~Ø1 1/2”
30˚
10 11
Close
Open LeftHot Water
Push
25˚ 90˚
12
13
87
Ø35~Ø38
Max
35
2178 17/32”
Max
1 3/
8”
9
11
1213
2345678
13
Codes/Standards Applicable:
Meets ASME A112.18.1M/A112.18.1
1.75gpm 6.6L/min maximum
GREEN
Water Efficiency
LEAD FREE
IAPMOR&T
TM
NSF/ANSI 61-9NSF/ANSI 372
KRAUS LIMITED LIFETIME WARRANTYThis product has been manufactured and tested to the highest quality standards by Kraus USA Inc. (“Kraus”). We offer our customers thoughtfully crafted fixtures & accesso-ries, engineered for enduring performance over years of use.
WHO IS COVERED BY THE WARRANTYThis warranty extends to the original purchaser only. This warranty is not transferable, between homes or owners and is only applicable to residential use.
WHAT IS COVERED BY THE WARRANTY Kraus warranties this product against defects due to material or craftsmanship error during the warranty period: Kraus will provide replacement parts at no charge, or at its option, replace any product or part of the product that is deemed defective, under normal installation, use, service and maintenance. If Kraus is unable to provide a replace-ment and repair is not practical or cannot be made in timely fashion, Kraus may elect to refund the purchase price in exchange for the return of the product.
CONDITIONS AND EXCLUSIONSLike other home fixtures, Kraus products will require light maintenance to ensure proper function. We provide you with complete knowledge to perform this maintenance and can also recommend resources if you are unable to fulfill this service.
A. Kraus will not be responsible for product failures due to lack of maintenance or proper use. Please read your care and maintenance documentation to determine the limits of proper use.
B. The original sales receipt, order number, and/or proof of purchase must be presented at the time of the warranty claim, without exception, for this warranty to be applied to all Kraus products.
C. Kraus recommends installing all Kraus products with a licensed, professional plumber. Kraus will not be held responsible for any damage or product failure due to improper installation, misuse, or failure to use a licensed professional. Please read your care and maintenance documentation to determine the limits of proper use.
D. Commercial use will automatically void this warranty.
E. This warranty is not applicable to Kraus products purchased from an unauthorized seller. For a complete list of authorized sellers please visit http://www.kraususa.com/where-to-buy.html
14
HELP LINE
Our customer service hours are Monday – Friday, 9am – 8pm EST.Be sure to visit our website at www.kraususa.com
NON-APPLICABILITY OF THIS WARRANTYBy the purchase and use of our products, you agree that Kraus is not liable for incidental, consequential or special damages associated with the return, replacement, installation or use of your product. This includes freight costs, cartridge replacement, labor, travel time, lost profit, home damages and other contingent liabilities and costs (including, without limitation, costs associated with experts, investigations, analyses, attorneys and other professionals and services). The Kraus warranty is a comprehensive and explicit limit of liability, and all items outside of it are not addressable by or the responsibility of Kraus. Certain states have variances regarding implied warranties and in those situations we remain fully compliant.
KRAUS USA Inc. makes no implication that products comply with any or all local building or plumbing codes. It is the consumer’s responsibility to determine local code
compliance. This warranty extends to the original purchaser and first consumer.
If you are a homeowner please contact a Kraus Customer Service Representative at:
Kraus USA, Inc. 12 Harbor Park DrivePort Washington, NY 11050Toll-free [email protected]
If you are a plumbing contractor or trade professional please contact a Kraus Pro Representative at:
Kraus USA, Inc. 12 Harbor Park DrivePort Washington, NY [email protected]
If you are an Authorized Partner please contact a Partner Support Representative at:Kraus USA, Inc. 12 Harbor Park DrivePort Washington, NY [email protected]
In requesting warranty service, please be ready to provide:
1. Proof of purchase. 2. A description of the problem.
www.kraususa.com