Match your application to the right system T A B...T1,T4,T5,T6,T8 A4 B1,B4 6 T4,T5 A1 B2,B4 7,8,9...
Transcript of Match your application to the right system T A B...T1,T4,T5,T6,T8 A4 B1,B4 6 T4,T5 A1 B2,B4 7,8,9...
-
Match your application to the right system
T A B
Tool Anchor BiT Accessory
-
For the Mechanical Contractor | Tools/Anchors/Bits Selection
Horizontal Pipe Brace
System:T4,T5,T8 A2 B2 1,2,6
T1,T5,T6 A4 B1 6
Equipment Mounts
System:
T4,T5,T8 A2 B2 1,2,6
T1,T4,T5,T6,T8 A4 B1 6
T4,T5,T8 A1 B2 7,8,9
Riser Guards
System:T4 A2 B2 1,2,6
T1,T4,T8 A4 B1 6
HVAC on the roof
System:
T4,T5 A2 B2 1,2,6
T1,T4,T5,T8 A4 B1 6
T4,T5,T8 A1 B2 7,8,9
Pipe Hangers
System:
T2,T3,T7 A6,A8 B1,B5 4
T4,T7 A3,A8 B3,B5 3
T2,T6,T7,T8 A7,A8 B2,B5 5
2
-
taB+s is a concept developed specifically for the contractor. It provides the optimum combination of Tools, ICC approved Anchors, Bits and Accessories(+) for a concrete application. Choose the application,then choose the system:
T A B tOOl aNCHOR BIt aCCeSSORY
Trapeze Hangers
System:
T2,T3,T7,T8 A6,A8 B1,B5 4
T4,T7 A3,A8 B3,B5 3
T2,T6,T7,T8 A7,A8 B2,B5 5
B1 B2Wedge-Bit SDS or
Wedge-Bit SDS Max CarbideStandard SDS+ Carbide Drill Bit
B3 B4SDS-Plus Accu-Bit for DropIn & Smart DI+
SDS Max Carbide Drill Bit
B5Carbide
Hole Saw
A1 A2 A3Adhesives Power-Stud+
SD1/SD2Smart-DI+
A4 A5 A6Wedge-Bolt+ Safe-T+ Pin Vertigo+
A7 A8Snake+ Cast-In-Place (Bang-It & Wood-Knocker)
1 2 3Sledge Hammer Calibrated
Torque WrenchSDI+ Setting Tool
4 5 6Vertigo+ Driver
SocketSnake+ Setting
ToolImpact Socket
7 8 9Adhesive
Dispensing ToolWire Brush Hand Air Pump
T1 T2 T3
DCF899 D25263K DCF887D2
T4 T5 T6
D25416K D25601K DCF880M2
T7 T8
DWD220 DCH273P2
Tools
Anchors
Bits
Accessories
TABs
3
-
For the Mechanical Contractor | Tools/Anchors/Bits Selection
Tools TABs Tools, Anchors, Bits + Accessories.
Pipe Hangers Through Metal Deck
System:
T2,T3,T7,T8 A6,A8 B1,B5 4
T4,T7,T8 A3,A8 B3,B5 3
T2,T6,T7,T8 A7,A8 B2,B5 5
Insulated Pipe Hangers
System:
T2,T3,T7,T8 A6,A8 B1,B5 4
T4,T7,T8 A3,A8 B3,B5 3
T2,T6,T7,T8 A7,A8 B2,B5 5
B1 B2Wedge-Bit SDS or
Wedge-Bit SDS Max CarbideStandard SDS+ Carbide Drill Bit
B3 B4SDS-Plus Accu-Bit for DropIn & Smart DI+
SDS Max Carbide Drill Bit
B5Carbide
Hole Saw
A1 A2 A3Adhesives Power-Stud+
SD1/SD2Smart-DI+
A4 A5 A6Wedge-Bolt+ Safe-T+ Pin Vertigo+
A7 A8Snake+ Cast-In-Place (Bang-It & Wood-Knocker)
1 2 3Sledge Hammer Calibrated
Torque WrenchSDI+ Setting Tool
4 5 6Vertigo+ Driver
SocketSnake+ Setting
ToolImpact Socket
7 8 9Adhesive
Dispensing ToolWire Brush Hand Air Pump
Anchors
Bits
Accessories
T1 T2 T3
DCF899 D25263K DCF887D2
T4 T5 T6
D25416K D25601K DCF880M2
T7 T8
DWD220 DCH273P2
4
-
HVAC Duct Trapeeze Hangers
System:
T2,T3,T7,T8 A6,A8 B1,B5 4
T4,T7,T8 A3,A8 B3,B5 3
T2,T6,T7,T8 A7,A8 B2,B5 5
Riser Clamps
System:
T4,T5,T8 A2 B2,B4 1,2,6
T1,T4,T5,T6,T8 A4 B1,B4 6
T4,T5,T8 A1 B2,B4 7,8,9
Seismic Bracing &
Pipe Hangers Thru Metal
Deck
System:
T2,T3,T7,T8 A6,A8 B1,B5 4
T4,T7,T8 A2,A8 B2,B5 1,2,6
T2,T6,T7,T8 A7,A8 B2,B5 5
Pumps, Pipes, Boilers & Equipment
System:
T4,T5 A2 B2,B4 1,2,6
T1,T4,T5,T6,T8 A4 B1,B4 6
T4,T5 A1 B2,B4 7,8,9
HVAC Duct Strap
System:T2 A5 B2 1
T2,T8 A2 B2 1,2,6
5
-
For the Mechanical Contractor | Tools/Anchors/Bits Selection
Pumps/Pipes/Boilers
System:
T4,T5,T8 A2 B2,B4 1,2,6
T1,T4,T5,T6,T8 A4 B1,B4 6
T4,T5,T8 A1 B2,B4 7,8,9
Horizontal Pipe Brace
System:
T4,T5,T8 A2 B2,B4 1,2,6
T1,T4,T5,T6,T8 A4 B1,B4 6
T4,T5,T8 A1 B2,B4 7,8,9
Toilet/Sink Stables
System:T4,T5,T8 A2 B2,B4 1,2,6
T1,T4,T5,T6,T8 A4 B1,B4 6
6
-
Sprinkler Pipe Hangers
System:
T2,T3,T7,T8 A6,A8 B1,B5 4
T4,T7,T8 A3,A8 B3,B5 3
T2,T6,T7,T8 A7,A8 B2,B5 5
Pipe Hangers
System:
T2,T3,T7,T8 A6,A8 B1,B5 4
T4,T7,T8 A2,A8 B3,B5 3
T2,T6,T7,T8 A7,A8 B2,B5 5
TABs Tools, Anchors, Bits + Accessories.
B1 B2Wedge-Bit SDS or
Wedge-Bit SDS Max CarbideStandard SDS+ Carbide Drill Bit
B3 B4SDS-Plus Accu-Bit for DropIn & Smart DI+
SDS Max Carbide Drill Bit
B5Carbide
Hole Saw
A1 A2 A3Adhesives Power-Stud+
SD1/SD2Smart-DI+
A4 A5 A6Wedge-Bolt+ Safe-T+ Pin Vertigo+
A7 A8Snake+ Cast-In-Place (Bang-It & Wood-Knocker)
1 2 3Sledge Hammer Calibrated
Torque WrenchSDI+ Setting Tool
4 5 6Vertigo+ Driver
SocketSnake+ Setting
ToolImpact Socket
7 8 9Adhesive
Dispensing ToolWire Brush Hand Air Pump
Tools
Anchors
Bits
Accessories
T1 T2 T3
DCF899 D25263K DCF887D2
T4 T5 T6
D25416K D25601K DCF880M2
T7 T8
DWD220 DCH273P2
7
-
T1 DCF899P120V Max XR Brushless High Torque 1/2" Impact Wrench Kit
Product Features
• Up to 700 ft-lbs of max torque; 1200 ft-lbs of max breakaway torque
• Compact: 8-13/16" length, 7.2 lbs
• Multi-speed control (0-400/ 1,200/ 1,900 RPM)
• 1/2" Anvil with detent pin (available in hog ring)
• LED light with 20 second delay
T2 D25263K1-1/8" D-Handle SDS Rotary Hammer Kit
Product Features
• SHOCKS - Active Vibration Control® reduces vibration felt by the user at the handles
• 3.0 Joules impact energy
• 8.5 amp motor: 0-1,450 RPM, 0-5,350 BPM
• Integral clutch
Accepts D25301D for dust management
T3 DCF887D220V Max XR Brushless 1/4" 3-Speed Impact Driver
Product Features
• Brushless motor; 0-1000/ 2800/ 3250 rpm,240/ 1500/ 1825 in-lbs
• 3-mode impact selector
• Drop & load easy grip chuck
• Compact: 5.3" length
T4 D25416K1" L-Shape SDS Rotary Hammer
Product Features
• SHOCKS - Active Vibration Control® reduces vibration felt by the user at the handles
• 9 amp motor: 0-820 RPM, 0-4,700 BPM
• Variable speed trigger
• 4.2 Joules impact energy
• 3-Mode selector
• E-Clutch Anti-rotational technolohy
• 360 degree side handle
Accepts D25301D or DWH052K for dust management
T5 D25601K1-3/4" SDS Max Combination Hammer
Product Features
• SHOCKS - Active Vibration Control® reduces vibration felt by the user at the handles
• 8.0 Joules impact energy
• 135 Amp motor with overload protection
• Electronic Variable Speed Dial
• Rear handle mount increases user comfort in down-drilling applications
• Electronic Soft Start provides the user more control when the trigger is pulled.
Accepts DWH050K for dust management
T6 DCF880M220V Max Lithium Ion 1/2" Impact Wrench
Product Features
• Compact: 5.70" (front /back), 3.4 lbs
• Three (3) LED lights with 20 second delay
• XR™ Li-Ion batteries with fuel gauge
• Textured anti-slip comfort grip
T7 DWD2201/2" VSR Pistol Grip Drill with E-Clutch Anti-Lock Control
Product Features
• E-Clutch® System shuts tool during stall
• 10.5 Amp motor delivers
• Patented motor design generates 50% more power with increased overload protection
• 0-1200 RPM, variable speed reversing switch
• Soft grip handle and two-finger trigger
• Metal gear housing
T7 DCH273P220V Max Brushless SDS Rotary Hammer
Product Features
• Brushless motor for extended runtime and durability
• SHOCKS - Active Vibration Control® significantly reduces vibration
• 2.1 Joules impact energy
Accepts D25303DH for dust management
8
For the Mechanical Contractor | Tools | Anchors
-
A1 AC100+Gold®
Acrylic Adhesive AnchorProduct Features
ESR-2582 Fire Test NSF 61 LEEDCat. 1 Cracked Report Certification Certification& Uncracked F120/Anchoring Concrete F180/Rebar
• Two-component vinylester adhesive anchoring system includes injection adhesive in plastic cartridges, mixing nozzles, dispensing tools and hole cleaning equipment
• Target applications: Anchoring, Rebar Doweling, Specified Use, General Use, Cold Weather
• Installation temp. range 14˚F to 95˚F
• Suitable for overhead installation, wet concrete and water-filled holes
• For rebar and threaded rod 3/8" to 1-1/4"; #3 to #10
AC100+Gold Product OfferingPowers # Size Box Ctn. Pal.
8478SD-PWR 10 fl. oz. Quik-Shot 12 36 648
8486SD-PWR 12 fl. oz. dual cartridge - 12 540
8490SD-PWR 28 fl. oz. dual cartridge - 8 240
For higher than 95˚F in-use temperature markets, consider Pure110+ epoxy. Technical information can be found at www.powers.com/adhesive anchors
A1 Pure110+®
Epoxy Adhesive AnchorProduct Features
QU
A L I F I C A TI O
N
SEIS
M IC REGION
DEPA
RTME
NT OF TRANSPORTATIO
N
UN
ITED STATES OF AME
RIC
A
ESR-3298 NSF 61 Seismic Dept. of Cracked Certification Region/Wind Transportation& Uncracked Loading ListedConcrete Qualification
• Two-component epoxy adhesive anchoring system includes injection adhesive in plastic cartridges, mixing nozzles, dispensing tools and hole cleaning equipment
• Target applications: Anchoring, Rebar Doweling, Specified Use, General Use
• Installation temp. range 50˚F to 110˚F; 40˚F with conditioning to 65˚F minimum
• For rebar and threaded rod 3/8" to 1-1/4"; #3 to #10
• Now also available in easy-pumping 3:1 formulation
Pure110+ Product OfferingPowers # Size Box Pallet
08310SD-PWR 9 fl. oz. Quik-Shot 12 432
08321SD-PWR 21 fl. oz. dual cartridge 12 540
08313SD-PWR 13 fl. oz. 3:1 mix ratio 12 540
08320SD-PWR 20 fl. oz. 3:1 mix ratio 12 540
A2 Power-Stud®+
Wedge Expansion Anchors
Power-Stud+ SD1 Product Features
CITy OF LOS ANGELES LARR
ESR-2818 Category 1 Cracked & Uncracked ConcreteESR-2966 Masonry
Report# 25787 ConcreteReport# 25864 Masonry
Report# 3033795
File# Ex1289
Base Material
Normal-Weight Concrete, Light Weight Concrete, Concrete Over Metal Deck, Grout Filled MasonrySize Range
1/4" diameter, 3/8" diameter through 1-1/4" diameter (Cracked & Uncracked Concrete) Anchor Material
Carbon Steel
• Fully threaded, torque-controlled, wedge expansion anchor
• Consistent performance in cracked & uncracked concrete
• Zinc plated carbon steel body and expansion clip
• Packed with nut and washer
• Patented & Additional Patents Pending
Power-Stud+SD1 Product OfferingPowers # Size Thread Length Box Ctn.
7400SD1-PWR* 1/4" x 1-3/4" 3/4" 100 600
7402SD1-PWR 1/4" x 2-1/4" 1-1/4" 100 600
7404SD1-PWR 1/4" x 3-1/4" 2-1/4" 100 600
7410SD1-PWR* 3/8" x 2-1/4" 7/8" 50 300
7412SD1-PWR* 3/8" x 2-3/4" 1-3/8" 50 300
7413SD1-PWR 3/8" x 3" 1-5/8" 50 300
7414SD1-PWR 3/8" x 3-1/2" 2-1/8" 50 300
7415SD1-PWR 3/8" x 3-3/4" 2-3/8" 50 300
7416SD1-PWR 3/8" x 5" 3-5/8" 50 300
7417SD1-PWR 3/8" x 7" 5-5/8" 50 200
7420SD1-PWR* 1/2" x 2-3/4" 1" 50 200
7422SD1-PWR 1/2" x 3-3/4" 2" 50 200
7423SD1-PWR 1/2" x 4-1/2" 2-3/4" 50 200
7424SD1-PWR 1/2" x 5-1/2" 3-3/4" 50 150
7426SD1-PWR 1/2" x 7" 5-1/4" 25 100
7427SD1-PWR 1/2" x 8-1/2" 6-3/4" 25 100
7428SD1-PWR 1/2" x 10" 8-1/4" 25 100
7430SD1-PWR* 5/8" x 3-1/2" 1-1/2" 25 100
7432SD1-PWR 5/8" x 4-1/2" 2-1/2" 25 100
7433SD1-PWR 5/8" x 5" 3" 25 100
7434SD1-PWR 5/8" x 6" 4" 25 75
7436SD1-PWR 5/8" x 7" 5" 25 75
7438SD1-PWR 5/8" x 8-1/2" 6-1/2" 25 50
7439SD1-PWR 5/8" x 10" 8" 25 50
7440SD1-PWR* 3/4" x 4-1/4" 1-3/4" 20 60
7441SD1-PWR* 3/4" x 4-3/4" 2-1/4" 20 60
7442SD1-PWR 3/4" x 5-1/2" 3" 20 60
7444SD1-PWR 3/4" x 6-1/4" 3-3/4" 20 60
7446SD1-PWR 3/4" x 7" 4-1/2" 20 20
7448SD1-PWR 3/4" x 8-1/2" 6" 10 60
7449SD1-PWR 3/4" x 10" 7-1/2" 10 40
7451SD1-PWR 3/4" x 12" 9-1/2" 10 40
Power-Stud+SD1 Product Offering, Continued
7450SD1-PWR* 7/8" x 6" 2-3/4" 10 40
7452SD1-PWR 7/8" x 8" 4-3/4" 10 40
7454SD1-PWR 7/8" x 10" 6-3/4" 10 40
7461SD1-PWR* 1" x 6" 2-3/8" 10 30
7463SD1-PWR 1" x 9" 5-3/8" 10 30
7465SD1-PWR 1" x 12" 8-3/8" 5 20
7473SD1-PWR 1-1/4" x 9" 4-3/4" 5 15
7475SD1-PWR 1-1/4" x 12" 7-3/4" 5 15
* Sizes which are less than the minimum standard anchor length for strength design. The published length is the overall length of the anchor. Allow for fixture thickness plus one anchor diameter for the nut and washer thickness when selecting a length. All anchors are packaged with nuts and washers.
For a higher load seismic wedge expansion anchor option, consider Power-Stud+ SD2. Technical information: www.powers.com/mechanical anchors
Power-Stud+ SD2 Product Features
CITy OF LOS ANGELES LARR
ESR-2502 Category 1 Cracked & Uncracked Concrete
Report# 25831Concrete
Report# 3033795
File# Ex1289
Base Material
Normal-Weight Concrete, Light Weight Concrete, Concrete Over Metal Deck, Grout Filled MasonrySize Range
3/8" diameter through 3/4" diameter Anchor Material
Carbon steel body with stainless steel expansion clip, carbon steel nut and washer
• Fully threaded, torque-controlled, wedge expansion anchor
• Consistent performance in high & low strength concrete
• Zinc plated carbon steel body, nut and washer
• Packed with nut and washer
• Patented & Additional Patents Pending
Power-Stud+ SD2Powers # Size Thread Length Box Ctn.
7413SD2-PWR 3/8" x 3" 1-3/4” 50 300
7414SD2-PWR 3/8" x 3-1/2" 2-1/4” 50 300
7415SD2-PWR 3/8" x 3-3/4" 2-1/2” 50 300
7416SD2-PWR 3/8" x 5" 3-3/4” 50 300
7422SD2-PWR 1/2" x 3-3/4" 2-1/8” 50 200
7423SD2-PWR 1/2" x 4-1/2" 2-7/8” 50 200
7424SD2-PWR 1/2" x 5-1/2" 3-7/8” 50 150
7426SD2-PWR 1/2" x 7" 5-3/8” 25 100
7427SD2-PWR 1/2" x 8-1/2" 6-7/8” 25 100
7435SD2-PWR 5/8" x 4-3/4v 2-7/8” 25 100
7433SD2-PWR 5/8" x 5" 3-1/8” 25 50
7434SD2-PWR 5/8" x 6" 4-1/8” 25 75
7436SD2-PWR 5/8" x 7" 5-1/8” 25 75
7438SD2-PWR 5/8" x 8-1/2" 6-5/8” 25 75
7442SD2-PWR 3/4" x 5-1/2" 3-1/4” 20 60
7444SD2-PWR 3/4" x 6-1/4" 4” 20 60
7446SD2-PWR 3/4" x 7" 4-3/4” 20 60
7448SD2-PWR 3/4" x 8-1/2" 6-1/4” 10 40
The published size includes the diameter and the overall length of the anchor. All anchors are packaged with nuts and washers.
9
-
A3 Smart DI+® Drop In Anchor
Internally Threaded Expansion AnchorProduct Features
Report# 3040746 File# Ex1289
Base Material
ConcreteSize Range
1/4" – 3/4"Anchor Material
Carbon Steel
• Blue indicator clearly shows that the anchor is properly set.
• Patented plug design yields a higher percentage of the expansion at the bottom of the anchor, exactly where it is needed.
• Set using Smart Tool. Drill hole, slide the tool sleeve over carbide drill and lock into place. The hammer drill does all the setting work for you.
Smart DI+ Anchor Product OfferingPowers # Size Box Ctn.
6304SD-PWR 1/4" 100 1000
6306SD-PWR 3/8" 50 500
6308SD-PWR 1/2" 50 250
For a higher load drop in anchor option, consider 5/8"-1" Standard Drop-In. Technical and ordering information can be found at www.powers.com/mechanical anchors
A4 Wedge-Bolt+Screw Anchor
Product Features
CITy OF LOS ANGELES LARR
ESR-2526 Category 1 Cracked & Uncracked ConcreteESR-1678 Masonry
Report# 25808 Concrete
Base Material
Normal-Weight Concrete, Light Weight Concrete, Concrete Over Metal Deck, Grouted CMUSize Range
1/4" diameter, 3/8" diameter through 3/4" diameter (Cracked & Uncracked Concrete) Anchor Material
Zinc plated carbon steel body & hex head or mechani-cally galvanized carbon steel body & hex head
• One piece, heavy duty screw anchor with finished hex head
• Simple to install, easy to identify and removable
• Suited for many applications in a variety of base materials
• Consistent performance in cracked and uncracked concrete
• Install with matched tolerance Wedge-bit
Wedge-Bolt+ Product OfferingPowers # Size Min. Embed. Box Ctn.
7204SD-PWR 1/4" x 1-1/4"* 1" 100 600
7206SD-PWR 1/4" x 1-3/4"* 1" 100 600
7207SD-PWR 1/4" x 2" 1-3/4" 100 600
7208SD-PWR 1/4" x 2-1/4" 1-3/4" 100 600
7210SD-PWR 1/4" x 3" 1-3/4" 100 500
7220SD-PWR 3/8" x 1-3/4"* 1-1/2" 50 300
7222SD-PWR 3/8" x 2-1/2" 2-1/8" 50 300
7224SD-PWR 3/8" x 3" 2-1/8" 50 250
7226SD-PWR 3/8" x 4" 2-1/8" 50 250
7228SD-PWR 3/8" x 5" 2-1/8" 50 250
7230SD-PWR 3/8" x 6" 2-1/8" 50 150
7240SD-PWR 1/2" x 2"* 1-3/4" 50 150
7242SD-PWR 1/2" x 2-1/2"* 1-3/4" 50 200
7244SD-PWR 1/2" x 3" 2-1/2" 50 150
7248SD-PWR 1/2" x 5" 2-1/2" 25 100
7250SD-PWR 1/2" x 6" 2-1/2" 25 75
7268SD-PWR 1/2" x 6-1/2" 2-1/2" 25 75
7252SD-PWR 1/2" x 8" 2-1/2" 25 75
7260SD-PWR 5/8" x 3"* 2-1/2" 25 100
7262SD-PWR 5/8" x 4" 3-1/4" 25 100
7264SD-PWR 5/8" x 5" 3-1/4" 25 75
7266SD-PWR 5/8" x 6" 3-1/4" 25 75
7270SD-PWR 5/8" x 8" 3-1/4" 25 75
7280SD-PWR 3/4" x 3"* 2-1/2" 20 60
7282SD-PWR 3/4" x 4"* 3" 20 60
7284SD-PWR 3/4" x 5" 4-1/4" 20 60
7286SD-PWR 3/4" x 6" 4-1/4" 20 60
7288SD-PWR 3/4" x 8 " 4-1/4" 10 40
7290SD-PWR 3/4" x 10" 4-1/4" 10 40Wedge-Bolt+ Mechanically Galvanized Product Offering
7726SD-PWR 3/8" x 4" 50 250
7728SD-PWR 3/8" x 5" 50 250
7730SD-PWR 3/8" x 6" 50 150
7746SD-PWR 1/2" x 4" 50 150
7748SD-PWR 1/2" x 5" 25 100
7750SD-PWR 1/2" x 6" 25 75
7751SD-PWR 1/2" x 6-1/2" 25 75
7752SD-PWR 1/2" x 8" 25 75
7764SD-PWR 5/8" x 5" 25 75
7766SD-PWR 5/8" x 6" 25 75
7768SD-PWR 5/8" x 6-1/2" 25 75
7770SD-PWR 5/8" x 8" 25 75
* Sizes which are less than the minimum standard anchor length for strength design. The published length is measured form below the hex washer head to the end of the anchor. Wedge-Bolt+ is marked with a blue tip and must be installed with a matched tolerance Wedge-Bit.
A5 Safe-T+ Pin®
Nail AnchorBase Material
Concrete, Block, Brick and StoneSize Range
1/4" x 1-3/8" and 1/4 x 2-1/2"Anchor Material
Carbon Steel
• One piece, all steel nail drive anchor
• Each box comes with a 6mm SDS carbide drill bit
• Easy to install...drill a hole and hammer in
• Typical applications HVAC duct straps, light to medium duty signage, termination bar, and flooring
Safe-T+ Pin Product Offering
Powers # Size Drill Dia. Box Ctn.
2800SD-PWR 6mm (1/4") x 1-3/8" 6mm 100 600
2801SD-PWR 6mm (1/4") x 2-1/2" 6mm 100 600
A6 Vertigo®+
Rod Hanger SystemProduct Features
ESR-2989 Category 1 Cracked & Uncracked Concrete Base Material
ConcreteSize Range
For rod sizes 1/4", 3/8 and 1/2"Anchor Material
Carbon Steel, yellow Dichromate Finish
• Threaded fastening system for suspending steel threaded rod and other assemblies
• Install with the appropriate size Vertigo Concrete Driver Socket (See accessories page)
• Packed with SDS Wedge-Bit
Vertigo+ Product OfferingPowers # Rod Size Screw Shank & Length Box Ctn.
7180SD-PWR 1/4" 3/8" x 2-1/8"" 100 1000
7181SD-PWR 3/8" 3/8" x 2-1/8"" 50 500
718sSD-PWR 1/2" 3/8" x 2-1/8"" 50 300
TABs10
For the Mechanical Contractor | Anchors | Bits
-
A7 Snake+®
Internally Threaded Self-Tapping AnchorProduct Features
CITy OF LOS ANGELES LARR
ESR-2272 Category 1Cracked & Uncracked Concrete
Report# 25810 Concrete
Base Material
Normal Weight Concrete, Light Weight Concrete, Concrete Over Metal DeckSize Range
1/4", 3/8", 1/2" dia. (Cracked & Uncracked Concrete)Anchor Material
Zinc Plated Carbon Steel
• Internally threaded self-tapping screw anchor
• Consistent performance in cracked or uncracked concrete
• No hammer needed
• Packed with SDS Wedge-Bit & Snake+ setting tool
Snake+ Product Offering
Powers # Size Min. Hole Depth
Internal ThreadDepth
Box Ctn.
6400SD-PWR 1/4" 2" 22/32" 100 1000
6401SD-PWR 3/8" 1-5/8" 11/16" 50 500
6403SD-PWR 1/2" 2-1/2" 29/32" 50 300
A8 Bang-It & Wood-KnockerCast-In-Place Anchors
Product Features
ESR-3657 Cracked Concrete
FILE# J.I.3015153
FILE# EX1289
Base Material
Concrete, Light Weight ConcreteSize Range
1/4" through 3/4" diameter Anchor Material
Carbon Steel and Engineered Plastic
Bang-It
• Installs through pre-drilled metal composite deck (pan deck) used to support a newly poured concrete floor or roof slab
• Protective sleeve protrudes below deck surface for overhead attachment of steel threaded rod
• Color coded sleeves indicate rod sizes 1/4" through 3/4"; prevents material from clogging the internal threads and marks insert location
Bang-It Product OfferingPowers # Size Drill Dia. Box Pallet
7540-PWR 1/4" Brown 13/16" 100 4000
7542-PWR 3/8" Green 13/16" 100 4000
7544-PWR 1/2" yellow 13/16" 100 4000
7546-PWR 5/8" Red 1-3/16" 50 2400
7548-PWR 3/4" Purple 1-3/16" 50 2400
7560-PWR Bang-It Deck Driller - 1 -
Wood-Knocker
• Installs onto wooden forms used to support newly pour concrete floor slabs, roof slab, or walls
• Color-coded flange is easily seen embedded in the concrete when forms are stripped
• Accepts threaded rod or bolt sizes 1/4" – 3/4"
Wood-Knocker Product Offering
Powers # Size Box Pallet
7550-PWR 1/4" Brown 200 9600
7552-PWR 3/8" Green 200 9600
7554-PWR 1/2" yellow 200 9600
7556-PWR 5/8" Red 150 6000
7558-PWR 3/4" Purple 150 6000
7567-PWR 1/2" Coil Thread Version 200 9600
7568-PWR 3/4" Coil Thread Version 150 600
B1 Wedge-BitsSDS-Plus
Product Features
SDS-Plus Shank High Impact Tip 2 Cutter
• Special matched tolerance range; maximum per-formance for Wedge-Bolt+ and Vertigo+ anchors
• Blue color matches anchor tip for system recognition
SDS-Plus Wedge-Bit Product OfferingDEWALT # Powers # Diameter Usable Length Overall Length
N/A 1312-PWR 1/4" 2" 4"
N/A 1314-PWR 1/4" 4" 6"
N/A 1315-PWR 1/4" 6" 8"
N/A 1316-PWR 3/8" 4" 6"
N/A 1318-PWR 3/8" 6" 8"
N/A 1319-PWR 3/8" 16" 18"
N/A 1332-PWR 3/8" 10" 12"
N/A 1320-PWR 1/2" 4" 6"
N/A 1322-PWR 1/2" 8" 10"
N/A 1334-PWR 1/2" 10" 12"
N/A 1335-PWR 1/2" 16" 18"
N/A 1324-PWR 5/8" 6" 8"
N/A 1326-PWR 5/8" 10" 12"
N/A 1336-PWR 5/8" 16" 18"
SDS-Plus Wedge-Bit Product Offering, Continued
N/A 1328-PWR 3/4" 6" 8"
N/A 1330-PWR 3/4" 10" 12"
SDS-MaxProduct Features
SDS-Max Shank High Impact Tip
SDS-Max Wedge-Bit Product OfferingDEWALT # Powers # Diameter Usable Length Overall Length
N/A 1354PWR 1/2" 8" 13"
N/A 1356-PWR 5/8" 8" 16"
N/A 1357-PWR 5/8" 16" 13"
N/A 1358-PWR 3/4" 8" 13"
B2 Standard Carbide BitsSDS-Plus
Product Features
SDS-Plus Shank 2-Cutter Tip
• Use in a rotary hammer equipped with an SDS (slotted drive shaft) type chuck
• Conform with ANSI Standard B212.15
• Can be used in concrete block brick & soft stone
SDS-Plus Carbide Bit Product OfferingDEWALT # Powers # Diameter Usable Length Overall Length
DW5401 0302-PWR 5/32" 4-1/2" 6-1/2"
DW5402 0304-PWR 3/16" 2-1/2" 4-1/2"
DW5403 0306-PWR 3/16" 4-1/2" 6-1/2"
DW5404 0308-PWR 3/16" 6-1/2" 8-1/2"
DW5405 0310-PWR 3/16" 8" 10"
DW5406 0312-PWR 3/16" 10" 12"
DW5407 0314-PWR 3/16" 12" 14"
- 0316-PWR 7/32" 6" 8-1/4"
DW5412 0317-PWR 7/32" 8" 11"
- 0318-PWR 7/32" 12" 14"
- 0319-PWR 7/32" 14" 16"
DW5416 0320-PWR 1/4" 2" 4-1/2"
DW5417 0321-PWR 1/4" 4" 6-1/2"
DW5418 0322-PWR 1/4" 6-1/2" 8-1/2"
DW5420 0323-PWR 1/4" 9" 11"
DW5421 0324-PWR 1/4" 12" 14"
- 0325-PWR 1/4" 14" 16"
- 0327-PWR 1/4" 18" 20"
DW5424 0329-PWR 5/16" 4-1/4" 6-1/4"
DW5426 0331-PWR 5/16" 10" 12"
DW5427 0333-PWR 3/8" 4-1/4" 6-1/2"
DW5429 0334-PWR 3/8" 8-1/4" 10-1/4"
DW5430 0336-PWR 3/8" 10-1/4" 12-1/4"
DW5431 0338-PWR 3/8" 16" 18"
DW5432 0339-PWR 3/8" 22" 24"
- 0341-PWR 7/16" 4-1/4" 6-1/4"
DW5435 0343-PWR 7/16" 10-1/4" 12-1/4"
DW5437 0346-PWR 1/2" 4-1/4" 6-1/2"
DW5438 0348-PWR 1/2" 8-1/4" 10-1/4"
Offering Continues on Next Page
11
-
SDS-Plus Carbide Bit Product Offering, Continued from Previous Pg.DEWALT # Powers # Diameter Usable Length Overall Length
DW5439 0349-PWR 1/2" 10-1/4" 12-1/4"
DW5540 0351-PWR 1/2" 16" 18"
DW5441 0352-PWR 1/2" 22" 24"
DW5442 0354-PWR 9/16" 4-1/4" 6-1/4"
- 0355-PWR 9/16" 8" 10-1/4"
DW5443 - 9/16" 10" 12"
DW5444 - 9/16" 16" 18"
DW5445 - 9/16" 22" 24"
DW5446 0359-PWR 5/8" 6" 7-3/4"
DW5447 0361-PWR 5/8" 10" 12"
DW5448 0362-PWR 5/8" 16" 18"
DW5449 - 5/8" 22" 24"
DW5450 0364-PWR 11/16" 6" 8"
- 0365-PWR 11/16" 10" 12"
DW5453 0368-PWR 3/4" 6" 8"
DW5455 0370-PWR 3/4" 10" 12"
DW5456 0371-PWR 3/4" 16" 18"
DW5458 0373-PWR 27/32" 6" 8"
DW5460 0375-PWR 7/8" 6" 8"
DW5461 0376-PWR 7/8" 10" 12"
DW5462 0377-PWR 7/8" 16" 18"
- 0379-PWR 1" 6" 8"
DW5464 0380-PWR 1" 8" 10"
- 0381-PWR 1" 10" 12"
DW5466 0382-PWR 1" 16" 18"
DW5468 - 1-1/8" 8" 10"
DW5469 - 1-1/8" 16" 18"
B3 Smart DI+® Bits
SDS-Plus Product Features
SDS-Plus Shank 2-Cutter Tip
• Part of the Smart DI+ System; match with Smart DI+ Anchor and Smart DI+ Setting tool
SDS-Plus Accu-Bits Product OfferingDEWALT # Powers # Size For Dropin Size
N/A 00391SD-PWR 3/8" DI+ Drill Smart DI+ 1/4"
N/A 00397SD-PWR 1/2" DI+ Drill Smart DI+ 3/8"
N/A 00410SD-PWR 5/8" DI+ Drill Smart DI+ 1/2"
B4 Standard CarbideSDS-Max
Product Features
SDS-Max Shank 2-Cutter Tip
• DEWALT carbide tip design maximizes carbide surface contact for longer bit life
• U-Flute cleans debris out for fast, efficient drilling
• Open head design channels dust into flutes for quicker drilling
SDS-Max Carbide Bit Product OfferingDEWALT # Powers # Diameter Usable Length Overall Length
DW5801 N/A 9/16" 8" 13-1/2"
DW5802 N/A 9/16" 16" 21-1/2"
DW5803 N/A 1/2" 8" 13-1/2"
DW5804 N/A 1/2" 16" 21-1/2"
DW5870 N/A 5/8" 8" 13-1/2"
DW5871 N/A 5/8" 16" 21-1/2"
DW5872 N/A 3/4" 8" 13-1/2"
DW5873 N/A 3/4" 16" 21-1/2"
DW5874 N/A 7/8" 8" 13-1/2"
DW5875 N/A 7/8" 16" 21-1/2"
DW5876 N/A 1" 8" 13-1/2"
DW5877 N/A 1" 16" 21-1/2"
DW5878 N/A 1-1/8" 10" 15"
DW5879 N/A 1-1/8" 18" 22-1/2"
DW5880 N/A 1-1/4" 10" 15"
DW5881 N/A 1-1/4" 18" 22-1/2"
7562-PWR 7566-PWR
B5 Hole SawsFor Bang-It Cast in Place Anchors
Carbide Hole Saw Product OfferingDEWALT # Powers # Size Box
- 7562-PWR 13/16" for 1/4", 3/8" & 1/2" Bang-It 1
- 7564-PWR 1-3/16" for 5/8" and 3/4" Bang-It 1
- 7566-PWR Carbide Hole Saw Center Bit 1
For additional Hole Saw options see www.DEWALT.com
1 Sledge Hammer2.5 lb. Double Faced
Product Features
Made in U.S.A.
• Designed for striking metal, concrete, and stone
• Strong fiberglass handle with slip-resistant cushion grip
Specifications
Head Weight / Overall Weight 2.5 lbs. / 3.28 lbs.
Face Diameter 1-11/16"
Sledge Hammer Specifications, Continued
Head Length [in] 3
Handle Length [in] 14
Overall Length [in] 15-11/16
Specification ASME ASME B107.54
Product OfferingProto # Head Weight Face Diameter Total Weight
J1433G 2.5 lbs. 1-11/16" 3.28
2 Torque Wrench3/8" Drive Ratcheting Head
Product Features
Made in U.S.A.
• Calibrated to +/- 3% in clockwise direction and +/- 6% in counter clockwise direction
• Calibration is accomplished by mechanical loading of each wrench in a horizontal position, and performing a three click test at 20%, 60% and 100% of maximum instrument capacity
• Manufactured to meet precision/highly accurate applications such as military and aerospace
Specifications
Drive Size [in] 3/8
Head Width 1 [In] 1-1/32
Head Depth [In] 7/8
Overall Length [in] , Weight [Lbs] 11-7/8, 2.60
Style Micrometer
Finish Full Polish
Specification ASME ASME B107.14
Specification TO TO33K6-4-2193-1
Torque Wrench Product OfferingProto # Description
J6064CX3/8" Drive Ratcheting Head Micrometer Torque Wrench 40-200 in-lbs
3 Smart DI+® Setting Tool
For The Smart DI+ Anchor System
• Part of the Smart DI+ System; match with Smart DI+ Anchor and Smart DI+ Setting tool
Smart DI+ Setting Tool Product OfferingPowers # Size For Smart DI+ Size
00425SD-PWR 1/4" 1/4"
00427SD-PWR 3/8" 3/8"
00429SD-PWR 1/2" 1/2"
12
For the Mechanical Contractor | Bits | Accessories
-
4 Vertigo® + Accessories
For The Vertigo+ Rod Hanger System
Vertigo+ Driver Socket Product OfferingPowers # Size For Vertigo+ Size
7195-PWR 1/4" 1/4"
7197-PWR 3/8" 3/8"
7198-PWR 1/2" 1/2"
Vertigo+ Pole Tool Product OfferingPowers # Description
7166-PWRPole tool telescopes from 6' to 12' to access hard to reach overhead areas. Includes Three Jaw Chuck
5 Snake+® Driver Socket
For Snake+ Anchors
Snake+ Driver Socket Product OfferingPowers # Size For Snake+ Size
6304-PWR 1/4" 1/4"
6306-PWR 3/8" 3/8"
6308-PWR 1/2" 1/2"
6 Impact Socket3/8" Drive Ratcheting Head
Product Features
Made in U.S.A.
• High strength magnets
• Require no bushings to hold the magnet in place. Allows room for more magnet material.
• Easily picks up heavy fasteners and holds them tightly during use
• Size stamped on tool for easy identification
Specifications
Size [mm] 8
Nut End Outside Diameter [in] 1/2
Drive end Outside Diameter [in] 1/2
Nut Depth [in] 1/8
Overall Length [in], Weight [lbs} 15/16, 0.04
Drive Size [in] 1/4
Point Size 6
Finish Black Oxide
Unit of Measure, Metric
Specification ASME ASME B107.33
Impact Socket Product OfferingProto # Description
J6908MHF1/4" Drive Metric High Strength Magnetic Impact Socket 8 mm - 6 Point
7 Dispensing Tools For AC100+Gold Adhesive
Manual Dispensing Tools for AC100+Gold Product OfferingPowers # Description
08437-PWR Tool for 10 oz. cartridge
08479-PWR High performance tool for 10 oz. cartridge
08485-PWR High performance tool for 10 & 12 oz. cartridges
08494-PWR Standard all metal tool for 28 oz. cartridge
08495-PWR High performance tool for 28 oz. cartridge
Manual Dispensing Tools for Pure110+ Product OfferingPowers # Description
08409-PWR Std. all metal tool for 21 oz. cartridge
08421-PWR High performance tool for 21 oz. dual cartridge
08437-PWR Tool for 9 oz. Quik-Shot cartridge
08494-PWR High performance tool for 9 oz. Quik-Shot cartridge
08298-PWR Std. tool for 13 + 20 oz. 3:1 mix ratio cartridges
Powered Dispensing Tools for Pure110+ Product OfferingPowers # Description
08442-PWR Battery powered tool for 21 oz. dual cartridge
08279SD-PWRBattery powered tool for 13 + 20 oz. 3:1 mix ratio cartridges
08479-PWRPneumatic tool for 13 + 20 oz. 3:1 mix ratio cartridges
8 Wire Brushes Clean Drilled Holes During Adhesive Installation
Hole Cleaning Accessories Product OfferingPowers # Wire Brushes Length
08284-PWR For 7/16" ANSI hole (3/8" rod / #3 rebar) 6-3/4"
08285-PWR For 9/16" ANSI hole (1/2" rod / #4 rebar) 6-3/4"
08275-PWR For 5/8" ANSI hole (5/8" rod / #4 rebar) 6-3/4"
08286-PWR For 11/16" ANSI hole (5/8" rod / #5 rebar) 7-7/8"
08278-PWR For 3/4" ANSI hole (5/8" rod / #5 rebar) 7-7/8"
08287-PWR For 7/8" ANSI hole (3/4" rod / #6 rebar) 7-7/8"
08288-PWR For 1" ANSI hole (7/8" rod / #7 rebar) 11-7/8"
08289-PWR For 1-1/8" ANSI hole (1" rod / #8 rebar) 11-7/8"
08290-PWR For 1-3/8" ANSI hole (1-1/4" rod / #9 rebar) 11-7/8"
08291-PWR For 1-1/2" ANSI hole ( #10 rebar) 11-7/8"Wire Brush Accessories
08283-PWR SDS-plus adapter for steel brushes
08296-PWR Std. drill adapter for steel brushes (Jacobs Chuck)
08282-PWR Steel brush extension, 12"
13
-
DWM120KDeep Cut Band SawSpecificationsAmps 10AmpsFt/Min 100-350fpmMax Capacity (Round) 5”Max Capacity (Rect.) 5” x 4-3/4”LED Light yesAC/DC Capability No
DCS373P220V Max Lithium Ion SawSpecificationsNo Load Speed 3,700rpmBlade Diameter 5-1/2"Max Watts Out 460MWOVoltage 20
DCS371P1 20V Max Lithium Ion Band SawSpecificationsBlade Length 32-7/8"Max Capacity (Round) 2-1/2" Rnd. & Sq.Cutting Speed 740fpm
DCS380P120V Max Lithium Ion Reciprocating SawSpecificationsStrokes/Min 0-3000spmStroke Length 1-1/8"Variable-Speed DialKeyless, 4-Position Blade Clamp
DCD995M220V Max XR Lithium Ion Brushless Premium 3-Speed HammerdrillSpecificationsNo Load Speed 0-430rpmDrive 1/4" Hex
DCD780C220V Max Lithium Ion Compact Drill /Driver KitSpecificationsMax rpm 2,000 Max Power 350UWO
DWE402/DWE402N4-1/2” Small Angle GrindersSpecificationsAmps 11.0 Ampsrpm 11,000 rpmMax Watts Out 1,400 WSpindle Size, Thread 5/8”-11”No Load Speed 11,000 rpm
DCG412P220V Max Lithium Ion Grinder KitSpecificationsNo Load Speed 7000.0rpmSpindle Thread 5/8-11Use Wheels rpm over 10000rpm
DCV58018/20V Max Cordless Wet-Dry VacuumSpecificationsNo Load Speed 7000.0rpmSpindle Lock 5/8-11Spindle Thread 5/8-11Use Wheels rpm Above 10000rpmTool Weight 5.1lbs
DCB09012V/20V Max USB Power SourceSpecificationsCompatible 12V/20V MAX*
DCR018Compact Worksite RadioSpecificationsVoltage / Compatible 18V/20V/12VWeight 6 lbs
DW089KSelf Leveling 3 Beam Line LaserSpecifications2x Brighter diodeAccurate to +/- 1/8" @ 30'Built-in magnetic pivot bracket
DWV012Wet / Dry HEPA Dust Extractor SpecificationsTank Size 10galAmps 15AmpsMax CFM 155CFMWeight 33.5lbsPower Cord 15ftHose 1-1/4” x 15ftSee dust extractor accessories D25301D, DWH050K and D25303DH listed with corresponding tools on page 8.
DCF681N28V Max Gyroscopic Screwdriver With Conduit ReamerSpecificationsNo Load Speed 0-430rpmDrive 1/4" Hex
DCF682N18V Max Gyroscopic Inline ScrewdriverSpecificationsNo Load Speed 0-430rpmDrive 1/4" Hex
Hole Saws & Reciprocating BladesDWA4186 6” 2X
™ Premium Metal Cutting Blade; 5 Pk.
DWA4188 8” 2X™ Premium Metal
Cutting Blade; 5 Pk.DWA4176 6” 10TPI 2X™ Recip Blade; 5 Pk.DWA4179 9” 10TPI 2X™ Recip Blade; 5 Pk.DWA4101 8pc. 2X Recip Blade SetDWA1801 2X™ Plumbers Holesaw 9 Pc. SetDWA1812 2X™ Plumbers Holesaw 3/4"DWA1814 2X™ Plumbers Holesaw 7/8"DWA1818 Bi-Metal Hole Saw 1-1/16”DWA1824 Bi-Metal Hole Saw 1-1/2”DWA1828 Bi-Metal Hole Saw 1-3/4”DWA1836 Bi-Metal Hole Saw 2-1/4”
Saw BladesDWA7747 14” 66T Heavy Gauge Ferrous Metal Cutting 1” arbor
DWA7770 5-1/2" 30T Ferrous Metal Cutting 2mm arborDWA7889 14” 100T Aluminum Cutting
1” arbor
Vacuum AccessoriesAccessoriesDW9315 15' Kink HoseDW9400 Disposable Plastic Liner, 5 Pk. DW9402 Fleece Bag, 5 Pk.DW9316 15' Anti Static HoseDW9401 Paper Bag, 5 Pk.DW9314 8' x 2-1/2" HoseDW9320 Replacemt. HEPA Filter, Typ1; 2 Pk.DW9330 Replacemt. HEPA Filter, Typ2; 2 Pk.Attachments
DWV2759BBeater Bar Floor Brush Kit Includes: 11" beater bar floor brush, 2 extension wands & storage bag
Connectors DWV9000 Universal Quick ConnectorDWV9110 Tapered Adapter 1.14" – 1.45"DWV9120 Tapered Adapter 1.37" – 1.54"DWV9130 Tapered Adapter 1.37"
DWV9140 Tapered Large Diameter Adapter 2.17" – 2.36"
14
For the Mechanical Contractor | Additional Tools
-
servicenet.dewalt.com or 1-800-4-DEWALT
ALABAMA Birmingham 205-942-0538
Mobile 251-602-1000
ALASKA Anchorage 907-561-7181
ARKANSAS Little Rock 501-372-3040
ARIZONA Phoenix 602-437-1200
CALIFORNIA San Francisco 510-783-3959
San Diego 858-279-2011
Anaheim 714-414-0369
Sacramento 916-344-3520
Ontario 909-930-1437
COLORADO Denver 303-922-8325
CONNECTICUT Hartford 860-563-5800
FLORIDA Ft. Lauderdale 954-321-6635
Tampa 813-884-0434
Jacksonville 904-781-2253
Orlando 407-657-0474
W. Palm Beach 561-689-3247
GEORGIA Atlanta 770-246-1710
HAWAII Honolulu 808-842-9925
IOWA Des Moines 515-270-1340
ILLINOIS Chicago South 708-614-1596
Chicago North 630-521-1097
INDIANA Indianapolis 317-243-8308
KANSAS Kansas City 913-495-4330
Wichita 316-943-1271
KENTUCKY Louisville 502-380-3748
LOUISIANA New Orleans 504-832-2187
Baton Rouge 225-296-3191
Shreveport 318-688-1553
MARYLAND Baltimore 410-536-0722
Capital Heights 301-333-0865
MASSACHUSETTS Boston 781-329-3407
MICHIGAN Grand Rapids 616-261-0425
Detroit 248-597-5000
MINNESOTA Minneapolis 952-884-9191
MISSOURI St Louis 314-997-9100
NEVADA Las Vegas 702-889-6025
NEW JERSEY Elmwood Park 201-475-3524
NEW MEXICO Albuquerque 505-884-1002
NEW YORK Buffalo 716-884-6220
Queens 718-335-1042
Rochester 585-334-7071
Long Island 631-952-2008
Albany 518-785-1867
NORTH CAROLINA
Charlotte 704-392-0245
Greensboro 336-852-1300
Raleigh 919-878-0357
OHIO Cleveland 440-842-9100
Cincinnati 513-772-3111
Columbus 614-895-3112
Toledo 419-867-8561
OKLAHOMA Oklahoma City 405-634-8403
Tulsa 918-249-8641
OREGON Portland 503-255-6556
PENNSYLVANIA Philadelphia 215-271-5500
Pittsburgh 412-642-0204
Allentown 610-435-9544
York 717-755-3441
SOUTH CAROLINA Charleston 843-745-9197
Greenville 864-299-8662
TENNESSEE Memphis 901-384-8100
Nashville 615-242-1633
Knoxville 865-688-0921
TEXAS Dallas 972-446-2996
Houston 713-466-1194
San Antonio 210-732-1221
Fort Worth 817-831-3828
El Paso 915-778-9769
Mcallen 956-661-1122
Austin 512-382-3971
UTAH Salt Lake City 801-486-5828
VIRGINIA Virginia Beach 757-363-0091
WASHINGTON Seattle 206-763-2010
Spokane 509-535-9252
WEST VIRGINIA Charleston 304-343-0289
WISCONSIN Milwaukee 414-645-4285
= Field Service Coordinator Location
DEWALT LocATions
ALABAMA + ATLANTA
6115-C Jimmy Carter Blvd. Norcross, GA 30071
770-246-1710
BOSTON 2 Powers Lane Brewster, NY 10509
800-524-3244877-871-1965
CHARLOTTE 349 L West Tremont Av-enue Charlotte, NC 28203
704-375-5012
CHICAGO 2472 Wisconsin Avenue Downers Grove, IL 60515
630-960-3156
DALLAS 1300 I-35 North, Suite #118 Carrollton, TX 75006
972-446-5985
DENVER 700 West Mississippi Ave. Unit B-1 Denver, CO 80223
303-922-9202
DETROIT 21600 Wyoming Avenue Oak Park, MI 48237
248-543-8600248-543-8601
FLORIDA 2412 Lynx Lane Orlando, FL 32804
813-626-4500813-626-4545
HOUSTON 13833 North Promenade Suite 100 Stafford, TX 77477
281-491-0351281-491-0367
INDIANAPOLIS 15290 Stony Creek Way Noblesville, IN 46060
317-773-1668317-773-1690
LOS ANGELES 2761 Dow Avenue Tustin, CA 92780
714-731-2500
MARYLAND 3137-B Pennsy Drive Landover, MD 20785
301-773-1722
MILWAUKEE 1650 Miller Parkway Milwaukee, WI 53214
414-645-8821
MINNEAPOLIS 351 Wilson Street, NE Minneapolis, MN 55413
612-644-3047
MISSOURI 3225 Harvester Road Kansas City, KS 66115
816-472-5033816-472-5040
NASHVILLE 221 Blanton Avenue Nashville, TN 37210
615-248-2667
NEW ORLEANS 102 Sampson Street Houston, TX 77003
713-228-1524713-228-1528
NEW YORK +PHILADELPHIA
2 Powers Lane Brewster NY 10509
800-524-3244877-871-1965
PHOENIX 3602 E. Southern Avenue Suite 5, Phoenix, AZ 85040
602-431-8024
PORTLAND 18609 72nd Avenue South Kent, WA 98032-1082
425-251-0312
ROCHESTER 245 Summit Point Drive Suite 2A Rochester, NY 14467
585-334-1423
SALT LAKE CITY
3120 W. California Avenue Suite E Salt Lake City, UT 84104
801-466-9428
SAN FRANCISCO
28970 Hopkins Street Suite D Hayward, CA 94545
510-293-1500
SEATTLE 18609 72nd Avenue South Kent, WA 98032-1082
425-251-0312
PoWErs FAsTEnErs BrAnch inFormATion NATION-WIDE CUSTOMER SERVICE: 1-800-524-3244
15
-
Powers and dewalt: two industry leading and trusted construction brands are now a complete solution for your fastening and anchoring needs.
engineered for peak performance and productivity when used together, Powers Fasteners and dewalt tools and accessories provide complete solutions for distributors and contractors.
Our fleet of service locations and jobsite representatives complete the package by canvassing the nation and are available for product support and safety training.
Copyright ©2016 DEWALT. The following are examples of trademarks for one or more DEWALT power tools and accessories: the yellow and black color scheme; the “D”-shaped air intake grill; the array of pyramids on the handgrip; the kit box configuration; and the array of lozenge-shaped humps on the surface of the tool.
Note: The information and data contained within this documentation was current as of February 2015. The information is for marketing purposes only and is subject to change and updates as needed. Powers Fasteners, Inc. reserves the right to change designs and specifications without notice or liability for such changes. Please contact Powers Fasteners for the most current and up to date available information or refer to our website at www.powers.com
Powers Fasteners 701 E. Joppa Road, Towson, MD 21286 P: (800) 524-3244 F:(877) 871-1965 www.powers.com Powers #PWRCONCMEPBR 1/16 ©2016 Powers Fasteners, Inc.
For more product information, call 800-524-3244 or visit us at:
www.powers.com www.dewalt.com www.protoindustrial.com