LIFT CONTROL SYSTEMS CATALOGUE - Talip … EN... · ARL-300 Functional Programmable Lift Control...

LIFT CONTROL SYSTEMS

CATALOGUE

All Your Needs For Elevators

ALBEN İnşaat Makine Elektrik Elektronik San. ve Tic. Ltd. Şti 2/23 Tavukçuyolu Cad. No:150/4 Yukarı Dudullu 34775 İstanbul – TÜRKİYE Tel: +90 216 526 39 70-71 Fax: +90 216 526 39 72 www.alben.com.tr

INDEX

1. Lift Control Cards ................................................................................................................... 3

2. Speed Control Units .............................................................................................................. 7

3. Emergency Rescue Cards .................................................................................................... 8

4. Lift Control Panels ................................................................................................................. 9

5. Photocells ............................................................................................................................ 14

6. Graphic LCD Displays ......................................................................................................... 15

7. Door Control Cards .............................................................................................................. 16

8. Inspection & Alarm Sets ...................................................................................................... 17

9. Magnetic Shelters ................................................................................................................ 19

10. Other Products .................................................................................................................... 20


ARL-500 Functional Programmable Lift Control Card

• All system parameters can be adjusted by using 6 buttons and an LCD placed on the card;

• Can be used with any command type up to 48 floors;

• Can be used at one speed, two speed, speed controlled and hydraulic lifts without any

extra parts. System can be selected from the menu;

• Can be used in group operation up to 8 elevators;

• All panels in the group are same and no extra panel is needed;

• Serial communication and pre-wired installation with car and landing modules via CAN

BUS;

• Floor detection is carried out by counter or encoder system. When an encoder is used,

braking and stopping adjustment can be made by using the buttons on the card or the

buttons on the car panel;

• Can be used in high speed elevators;

• Saving errors on system (last 256 records) with date and time information enables to track

past errors in detail;

• Automatic door control according to the stops is achieved by double automatic door

support;

• Side selective door operation individually determined for each stop;

• RS-232, RS-485 and 2 CAN BUS serial ports;

• Monitoring the lift status, giving commands, making adjustments and following errors are

possible by a connection to a local computer via RS-232 or to a remote computer using a

modem;

• Free programmable inputs and outputs on main controller, car controller and landing

modules for special purposes;

• Integrated door bridging safety relays for door pre-opening and re-leveling;

• Integrated motor phase protection relay;

• Hand held terminal for operating the controller from any point of CAN BUS;

• Designed according to European Lift Standard EN-81.

LIFT CONTROL

CARDS


ARL-300 Functional Programmable Lift Control Card

• Compatible with two speed, VVVF (geared and gearless) and hydraulic elevators;

• Can be used at any command type up to 24 stops;

• Can work with speeds up to 2 m/s;

• Car positioning with easy installation and safe detection;

• Integrated door bridging safety circuit for door pre-opening and re-leveling with open doors;

• Integrated motor-phase protection circuit;

• Integrated automatic door control inputs and outputs for single door;

• Emergency lowering with 2x12V batteries for hydraulic lifts. ARL-SARJ charger unit

controls the battery charge;

• Emergency evacuation functions for electric lifts:

o For geared drive: by an external evacuation device (e.g. AKUS-SD)

o For gearless drive: by releasing the brakes or by active motor driving

• Easy connection with only 15 cables by using serial car installation boards which reduces

labor and cable costs;

o FX_SERI for up to 16 floors

o FX_SERI_32 for more than 16 floors

• Connection boards, which, are used instead of panel terminals are supplied with flexible

parallel connection cables save extra connection terminals at control panel.

LIFT CONTROL

CARDS


ARL-200S Functional Programmable Lift Control Card

• All system parameters can be adjusted by using 4 buttons and an LCD placed on the card;

• Can be used with any command type up to 16 floors;

• Can be used at one speed, two speed and VVVF lifts without any extra parts. System can

be selected from the menu;

• Can be used in group operation up to 2 elevators. All panels in the group are same and no

extra panel is needed;

• Only two cables are needed for group communication;

• Floor detection is carried out by counter system. Only 3 magnetic switches for one speed

and 4 for two speed systems including limit switches are used for any number of floors;

• An error code with its explanation is displayed on the LCD in case of an abnormal

condition (e.g.. H1:Door cannot be locked);

• At normal condition the lift can be monitored by messages on the LCD (Waits for calls,

high speed, low speed, inspection);

• Each floor can be labeled by an alphanumeric character (L, P, E, F, H, b, o, 0, 1, 2, 3...);

• 7 Segment and signalization outputs are short-circuiting protected. In case of a short

circuit, the related output is shut down until problem is removed and a message stating

which output is in short-circuit is displayed on LCD (D segment short circuit);

• Only 15 cables are enough for system to work by using serial car connection (FX_SERI)

which reduces labor and cable costs;

• No extra switch is needed at high speed lifts (1.6 m/sec) for early slow down;

• Turkish, English, Dutch, Romanian, French language menu options;


LIFT CONTROL

CARDS


ARL-100 Control Card For Simple Systems

• An economical and practical card for one speed or two speed simple push button lifts up to

8 floors;

• System consists of only one unit (22 cm x 11 cm);

• Floor detection is carried out by counter system. Only 3 magnetic switches for one speed

and 4 for two speed systems including limit switches are used for any number of floors;

• All system parameters (Number of floors, busy delay, door lock wait time, automatic door

yes-no, max. floor to floor travel time, fire park floor, max. time to wait for door close, stop

at floor level on inspection) can be adjusted by user via 3 buttons and 7-segment display

on the card;

• 7-segment display indicates the car position at normal condition and displays an error code

at abnormal condition;

• Fire alarm input, earthquake sensor input, over-load input, car priority switch input,

direction arrow, car lamp, busy , out of service and automatic door outputs are available;

• 7-segment and signalization outputs are short-circuit protected;


LIFT CONTROL

CARDS


ADrive VVVF Inverter

• Can be used with asynchronous (geared) and synchronous (gearless) lift drives;

• Provides great travel comfort;

• Load-independent and sensitive stopping on the floors;

• High torque motor drive at all speed via space vector modulation;

• Up to 40% electrical usage savings;

• Elimination of startup problems with generators by the help of controlled motor current;

• Specifically designed for elevators. Special parameters for travelling comfort;

• 10 KHz IPM switching frequency for low noise motor drive;

• Energy consumption through an internal DC reactor;

• 4 low noise fans for efficient cooling;

• All isolated control inputs and outputs;

• Over-load, high voltage, low voltage, output short circuit, power lost, line phase control,

over heat, ground fault, over-torque and other necessary protection functions;

• EMC tested and verified;

• 7.5 kW, 11 kW, 15 kW and 22 kW power rating models;

• Anti-rollback function to prevent the rollback without a load cell unit;

• Automatic travel curve correction function for short floors;

• Over-gain detection function to prevent motor oscillation.

SPEED CONTROL

UNITS


AKUS-SD Combi Emergency Rescue Card

• In case of mains failure it moves the lift which stopped between two floors to floor level,

opens the automatic door and passengers are evacuated in safety;

• For lifts with automatic doors, if mains failure occurs at floor level, door is opened and

passengers are evacuated;

• Can be applied to all one speed, two speed or speed-controlled systems;

• Suitable for asynchronous drives;

• Works open loop. No need to put a sensor on the motor;

• Includes an internal transformer;

• Gets the power from 5 pieces of batteries which need no maintenance;

• Thanks to smart battery charge system which does not tire the batteries and makes them

work for many years;

• Because it is integrated into control panel, all the connections necessary for emergency

unit is done in fabric. So the setup time is minimized;

• No safety circuit connection is needed. Safety circuit connection is only made to lift

controller;

• Can be disabled with a few cable connection in case of failure;

• The starting delay of rescue operation can be adjusted for buildings have diesel

generators;

• With LCD program parameters like: max travel time, automatic door type, motor drive

frequency, door opening time, starting delay, language e.tc. can be adjusted easily;

• Lift monitoring and error reporting with user-friendly menu interface;

• Turkish, English language menu options;

• Designed according to EN81-1.

EMERGENCY RESCUE CARDS


ARL-100 Lift Control Panels

• Number of Stops: Up to 8 Stops;

• Driving Type: One Speed & Two Speed;

• Lift Speed: Up to 1 m/sec;

• Command Type: Simple Push Button;

• Group Operation: Not Available;

• Car and Landing Installation: Parallel Installation;

• Car Positioning: By bi-stable magnetic switches and round magnets;

• Car Entrance: Double door control with an extra Auto-Kg;

• Automatic Door Control: Any type of automatic door;

• Emergency Rescue System: By AKUS-SD integration into the control panel;

• Motor Phase Protection: With MKR-02C motor phase protection unit support;

• Indicator Code Outputs: Built-in 7-segment indicator outputs;

Gray & binary code outputs with GKS card;

Simple indicator code output;

• Safety Circuit Connections: Special connection for safety circuit by KBK-5 board;

• Compatibility: Full conformance to EN 81-1 as a complete elevator

control panel.

LIFT CONTROL PANELS


ARL-200S Lift Control Panels


• Drive Type: One Speed, Two Speed & VVVF;

• Lift Speed: Up to 1.6 m/sec;


Parallel command (inside/outside mixed);

Single button up & down collective;

Single button up collective;

Single button down collective;

Full Collective;

• Group Operation: Up to 2 elevators;

• Car Installation: Serial car installation with RK22 inspection box support

Parallel car installation;

• Landing Installation: Parallel landing installation;

• Car Positioning: By bi-stable magnetic switches and round magnets;

• Car Entrance: Double door control with an extra Auto_Kg;



• Motor Phase Protection: With MKR-02C motor phase protection unit support;

• Indicator Code Outputs: Built-in 7-segment indicator outputs;

Gray & binary code outputs with GKS card;


• Compatibility: Full conformance to EN 81-1 as a complete elevator

control panel.

LIFT CONTROL PANELS


ARL-300 Lift Control Panels


• Drive Type: Two Speed, VVVF (geared & gearless) & Hydraulic;



Parallel command (inside/outside mixed);

Single button up & down collective;

Single button up collective;

Single button down collective;

Full Collective;


• Car Installation: Serial car installation

Parallel car installation;

• Landing Installation: Parallel landing installation;

• Car Positioning: By mono-stable magnetic switches and bar magnets

for VVVF and hydraulic systems;

By bi-stable magnetic switches and round magnets for

two speed systems;

• Car Entrance: Automatic door control by built-in relays on main board

Double automatic door control by 2 Auto-Kg boards



By adding ARL-SARJ board (hydraulic systems);

• Door Bridging: Door pre-opening and re-leveling with open door;

• Motor Phase Protection: By built-in inputs and outputs on main board;

• Indicator Code Outputs: Built-in 7-segment, Gray & binary code outputs;


• Compatibility: Full conformance to EN 81-1 & EN 81-2 as a complete

elevator control panel.

LIFT CONTROL PANELS


ARL-500 Complete Lift Control Panels


• Drive Type: Two Speed, VVVF (geared & gearless) & Hydraulic;


• Command Type: Full collective;

Up or down collective;


• Communication with Car: Serial car communication via CANBus;

One to one connection by flexible cables with sockets

between control panel and inspection box;

Plug & play connection by one cable with socket

between COP and inspection box;

• Communication with Floors: Serial landing communication via CANBus;

CANBus line that is joined by cables with sockets from

floor to floor and that extends along the shaft;

Plug & play connection for landing operation panels by

cables with sockets that are connected to shaft

CANBus line at each floor;

• Door Contacts Wiring: Door contact installation that is joined by cables with

sockets from floor to floor and that extends along the

shaft;

Connection for landing doors plug & play contacts by

cables with sockets that are connected to door contact

installation;

• Shaft Wiring: Connection to pit box by one cable with sockets;

• Car Positioning: By encoder;

By magnetic switches and magnets;

LIFT CONTROL PANELS


ARL-500 Complete Lift Control Panels (cont’d)

• Automatic Door Control: Automatic Door Control for any type of door;

Independent door control for each floor by double door

support;

1 door control input/output in inspection box, 2 in

control panel

• Indicator Options for COP: 240 x 128 pixels graphic LCD indicator;

128 x 64 pixels graphic LCD indicator (vertical /

horizontal);

2 x 30 mm dot matrix display;

3 x 30 mm dot matrix display

• Indicator Options for LOP: 240 x 128 pixels graphic LCD indicator (over door);

128 x 64 pixels graphic LCD indicator (vertical);



Call module without display;


By adding ARL-SARJ board (hydraulic systems);

• Door Bridging: Door pre-opening and re-leveling by relays on board;

• Motor Phase Protection: By built-in inputs and outputs on main board;

• Programmable Inputs / Outputs: Free programmable inputs / outputs on main board,

car boards and landing boards;

• Test Functions: Special test function to test the connections of car and

landing button panels;

• Remote Control: Control of ARL-500 main board and ADrive VVVF

inverter by hand terminal that is connected to the

CANBus line from any point;

• Safety Circuit Connections: Special connections in control panel, inspection box

and pit box for safety circuits;

• Car and Shaft Supply: Earth fault protected fuses for car and shaft lights;

• Shaft Light Circuit: Shaft light circuit via current pulse relay (activated with

buttons in inspection box and pit box);

• Emergency Alarm: Emergency alarm siren (activated with buttons in

inspection box and pit box);

• Compatibility: EMC tested and verified;

Full conformance to EN 81-1 and EN 81-2 as a

complete elevator control system.

LIFT CONTROL PANELS


FSL1N One Beam Photocell

• 1 infrared sensor;

• Composed of faced sensors;

• Has NO/NC relay contact output.

FSL2N Two Beam Photocell

• 2 infrared sensors;

• Composed of faced sensors;

• Has NO/NC relay contact output.

PHOTOCELLS PHOTOCELLS


LCD240X128A Graphic LCD Display

• Supports up to 32 floors;

• 240 x 128 pixels resolution (114 x 70 mm active area);

• General purpose displaying panel for car and landings;

• Support for CANBus, gray, binary code input, Arkel counter and 7-segment modes;

• Programmed by buttons on board or with a PC by using LCD240128A Uploader software;

• Individual picture programming for each floor;

• Programmable static / animated arrow;

• Programmable static / animated subtitle;

• Programmable ‘out of service’ and ‘overload’ images;

• Programmable logo;

• Selectable letters or numbers (-, 0…9, A…Z) for floor text;

• Saving or loading personal settings with the uploader;

• User pictures and logos can easily be added to system by PC software;

• Positive or negative common selectable;

• Time and date display (only in CANBus mode).

GRAPHIC LCD DISPLAYS


KM_20 Door Control Card (Telescopic Doors with 24VDC Motors)

• KM_20 provides complete hold of the motor with its 4 region motor control and high

resolution encoder input hardware;

• In addition to this hardware, it allows swift but comfortable motion of doors with its software

that provides S softening in travel ramps and which has the algorithm that does not require

limit switches;

• In order to work with the control panels in complete harmony it can generate “Doors are

completely open”, “Doors are fully closed” and “Obstruction detected” signals. These

signals enable it to work for fire lift doors;

• It provides many functions and parameters for manufacturing companies that enable

application flexibility, like motor reduction ratio, motor revolution, motor sheave

circumference and skate open zone;

• It provides features for auto-learning of door travel limits (without limit switches);

• A nudging function is included with buzzer sound and slow speed closing after a long time

photocell interrupt;

• In case of mains failure, it can get the power from 2 pcs 12V batteries and can make floor

controlled door opening. Km_20 controls the battery charge;

• All system parameters can be adjusted easily by user via buttons and LCD on the board;

• The door position data and the door commands will be monitored during normal operation

and the error message will be monitored during abnormal condition;

• Availability of multiple languages: Turkish and English.

DOOR CONTROL

CARDS


RK12 Standard Inspection Box (Battery Charge + Alarm + Gong)

• Compatible with systems with parallel car installation up to 16 stops;

• Emergency lightening lamp output at mains failure;

• Alarm;

• Gong;

• 12V battery and battery charge;

• 2 pieces of plugs;

• Lightening;

• Special connection for safety circuit by KBK-6 card support;

• Convenience of controlling from any point on the car by EK-1 hand terminal;

• Wide space for comfortable working.

RK22 Standard Inspection Box (FX_SERI + Battery Charge + Alarm + Gong)

• Serial car installation support up to 16 stops

• Includes all the features of RK12 Standard Inspection Box

• Includes FX_SERI Serial Car Connection Card

• Enables to save from costs by requiring less materials for car buttons, digital, overload, full

load, gong, direction arrows, car lamp, automatic door open & close buttons and inspection

movement buttons

• Special connection for safety circuit by KBK-6 card support

• Convenience of controlling from any point on the car by EK-1 hand terminal

• Wide space for comfortable working

INSPECTION & ALARM

SETS

INSPECTION & ALARM

SETS


RK32 Standard Inspection Box (FX_SERI-32 + Battery Charge + Alarm + Gong)

• Car installation support for ARL-300 control panels more than 16 stops;

• Includes all the features of RK12 Standard Inspection Box;

• Includes FX_SERI-32 Serial Car Connection Card;

• Enables to save from costs by requiring less materials for car buttons, digital, overload, full

load, gong, direction arrows, car lamp, automatic door open & close buttons and inspection

movement buttons;

• Special connection for safety circuit by KBK-6 card support;

• Convenience of controlling from any point on the car by EK-1 hand terminal;

• Wide space for comfortable working.

EK-1 Manual Controller

• Manual control from control panel;

• Inspection switch;

• Inspection movement buttons;

• Emergency stop (can be locked).

INSPECTION &

ALARM SETS

INSPECTION & ALARM

SETS


MTM Mono-Stable Magnetic Switch

General Features:

• Electronic circuit design;

• Long life due to working without contacts;

• Durable against vibrations;

• Visual inspection of operation by LEDs on board;

• Can be used in elevators where quick sensing is required;

• Can be used for door opening security zone;

• Can work independently from magnet pole;

• Easily installed by plastic legs.

Technical Features:

• Can work for 30 mm distance;

• 2 mili seconds response time

• Can work either with DC or AC input between 20V and 28V;

• 24 VDC / 100 mA; short circuiting and overload protected signal output;

• 95 x 18 mm dimensions;

• 1.5 m of cable length

Compatibility:

• EN81-1 and EN81-2;

• IEC 60068-2-6: Sinusoidal Vibration Test;

• IEC 60068-2-27: Mechanical Impact Vibration Test;

• IEC 60068-2-29: Crash Test;

MAGNETIC SWITCHES


FX_SERI Serial Car Connection Card

• Communicates with ARL-200S and ARL-300 control cards via two cables;

• No installation is needed between the car and control panel for car buttons, display,

overload, full load, gong, direction arrows, car lamp, automatic door close & open buttons

and inspection movement buttons. Only security, power and communication connections

are needed and 15 cables are enough for connection between car and control panel.

AUTO_KG Automatic Door Card

• Used with ARL-200S and ARL-100 control card;

• Can work with all three phase, single phase and electronic-controlled doors;

• Has light barrier input, door close input and door limit contact inputs;

• By using two potentiometers, the duration of light barrier's braking and door-open waiting

at the floor can be adjusted.

OTHER PRODUCTS


REV1 Inspection Box Card (Inspection/Gong/Alarm/Charge)

• Works with 24V supply voltage;

• 12V battery charge and emergency light outputs;

• Gong output, Alarm output.

MKR-02C Motor Phase Protection Card

• Phase turn control, Adjustable phase voltage control, PTC control;

• 48V DC leakage current control, Warning LEDs.

GKS Grey Code Driver

• Converts counter system data to Binary or Grey code.

OTHER PRODUCTS

OTHER PRODUCTS


GEVEZE Voice Announcement System

• ChatterBox is a floor announcement system designed for elevators. It notifies the name or

the number of the current floor with a human voice. It also gives “overload” and “out of

service” warnings;

• Grey code, binary code and counter modes are available as input modes;

• ChatterBox board comes loaded with default messages from the factory. But it can also be

customized with the help of a personal computer and the ChatterBox Loader Software.

MRL-Sarj 48V / 60V Battery Charger

• MRL-Sarj is constant output voltage, current limited lead acid battery charger specially

designed for 12V/7Ah maintenance-free, dry type batteries which charges the batteries

optimally with an appropriate charging technique;

• Available in 2 type: 48V (4 pcs. battery) and 60V (5 pcs. battery);

• With metal cased design, suitable for mounting in an enclosed panel;

• Status LEDs for AC input line and battery charge;

• Short circuit and overload protection;

• Suitable for 200-240Vac input voltage range;

• Dimensions 70mmx144mmx73mm (width x length × height).

OTHER PRODUCTS

OTHER PRODUCTS


LEVELED Floor Level Indicator

• Floor level indicator

• Buzzer for sound alert after car reaches the floor level in case main power fails

• Can be used with hydraulic and rope lifts

• Counter type selection via jumper

• External lamp output (12V/1W) which can be used to display levelled signal in a different

place

• Can be supplied with 12V or 24V battery voltage

FX-SERI-32 Serial Communication Unit (for ARL-300)

• Serial communication unit for ARL-300 lift controller designed for high-rise buildings;

• Supports for up to 24 floors;

• Communicates with ARL-300 lift controller via 2 cables;

• Used in inspection box for car commands, and in control panel for landing calls as an floor

expansion board;

• Operation mode selection (for car commands or landing calls) with a Jumper;

• Gray/Binary code outputs programmed with ARL-300 lift controller's menu;

• Display outputs A,B,C, ... on FX_SERI_32 board can be programmed as 7-segment, Gray

code, inverted Gray code, Binary code and inverted Binary code;

• No installation is needed betwen car and control panel for car buttons, indicators, over

load, full load, gong, direction arrows, car light, automatic door open / close buttons,

inspection operation buttons and Gray/Binary code outputs for position indicators.

OTHER PRODUCTS

OTHER PRODUCTS

LIFT CONTROL SYSTEMS CATALOGUE - Talip … EN... · ARL-300 Functional Programmable Lift Control...

Documents

Transcript of LIFT CONTROL SYSTEMS CATALOGUE - Talip … EN... · ARL-300 Functional Programmable Lift Control...