ABB-Welcome Lift control module M2306 M2307
Transcript of ABB-Welcome Lift control module M2306 M2307
VER:1.0 │ │ 20.10.2015
ABB-Welcome
Pos: 2 /Di nA4 - Anleitung en Online/Inhalt /KN X/D oorEntr y/83220- AP- xxx/Titelbl att - 83220-AP- xxx - ABB @ 19\mod_1323249806476_15.docx @ 111084 @ @ 1
Lift control module
M2306
M2307
=== Ende der Liste für Textmar ke Cover ===
ABB-Welcome
| — 2 —
Pos: 4 /Busch-Jaeger (Neus truktur)/M odul-Str uktur/Online-Dokumentation/Inhal tsverzeichnis (--> Für alle D okumente <--)/Inhaltsverzeichnis @ 19\mod_1320649044386_15.docx @ 109653 @ @ 1
1 Safety ............................................................................................................ 3 2 Environment .................................................................................................. 3
2.1 ABB devices ................................................................................. 3 3 Technical data ............................................................................................... 4 4 Function ......................................................................................................... 5 5 Connection .................................................................................................... 6
5.1 M2306 ........................................................................................... 6 5.2 M2307 ........................................................................................... 7
6 Mounting / Installation .................................................................................. 10 6.1 Requirements for the electrician ................................................. 10 6.2 Mounting ..................................................................................... 12
7 User case .................................................................................................... 13 7.1 One M2306 and M2307 .............................................................. 13 7.2 One M2306 and M2307 .............................................................. 15 7.3 Up to two lifts per building ........................................................... 17 7.4 Up to four lifts per building .......................................................... 18
8 Operation ..................................................................................................... 19 8.1 User Scenario Illustration of visitor
target floor .................................................................................. 19 8.2 User Scenario Illustration of resident
target floor .................................................................................. 20 9 Configuration through the PC software ........................................................ 21
9.1 Connected to PC ........................................................................ 21 9.2 Configuration .............................................................................. 22
=== Ende der Liste für Textmar ke TOC ===
ABB-Welcome
Pos: 6 /Busch-Jaeger (Neus truktur)/M odul-Str uktur/Online-Dokumentation/Überschriften (--> Für alle Dokumente <--)/1. Ebene/S - T/Sicherheit @ 18\mod_1302612791790_15.docx @ 103357 @ 1 @ 1
1 Safety Pos : 7 /Busch-Jaeger (Neus truktur)/M odul-Str uktur/Online-Dokumentation/Sicherheit (--> Für all e D okumente <--)/Warnhi nweise/Sicherheit - 230 V @ 18\mod_1302606816750_15.docx @ 103308 @ @ 1
Warning
Electric voltage!
Risk of death and fire due to electrical voltage of 100-240 V.
– Work on the 100-240V supply system may only be performed by
authorised electricians!
– Disconnect the mains power supply prior to installation and/or
disassembly!
Pos: 10 /Busch-Jaeg er (Neustr uktur)/Modul- Struktur /Online-Dokumentati on/Überschriften (--> Für alle D okumente <--)/1. Ebene/U - Z/U mwelt @ 18\mod_1302614158967_15.docx @ 103383 @ 1 @ 1
2 Environment Pos : 11 /Busch-Jaeg er (Neustr uktur)/Modul- Struktur /Online-Dokumentati on/U mwel t (--> Für alle D okumente <--)/Hinweise/Hi nweis - U mwelt - Hinweis Elektrog eräte @ 18\mod_1302763973434_15.docx @ 103500 @ @ 1
Consider the protection of the environment!
Used electric and electronic devices must not be disposed of with
domestic waste.
– The device contains valuable raw materials which can be recycled.
Therefore, dispose of the device at the appropriate collecting
depot.
Pos: 12 /DinA4 - Anl eitungen Onli ne/Ueberschrif ten/2./ABB Geraete @ 19\mod_1323162843832_15.docx @ 110875 @ 2 @ 1
2.1 ABB devices Pos : 13 /Busch-Jaeg er (Neustr uktur)/Modul- Struktur /Online-Dokumentati on/U mwel t (--> Für alle D okumente <--)/Hinweise/Hi nweis - U mwelt - ABB El ektr ogeräte @ 19\mod_1323162745839_15.docx @ 110867 @ @ 1
All packaging materials and devices from ABB bear the markings and test seals for
proper disposal. Always dispose of the packaging material and electric devices and their
components via the authorized collecting depots and disposal companies.
ABB products meet the legal requirements, in particular the laws governing electronic
and electrical devices and the REACH ordinance.
(EU-Directive 2002/96/EG WEEE and 2002/95/EG RoHS)
(EU-REACH ordinance and law for the implementation of the ordinance (EG)
No.1907/2006)
ABB-Welcome
3 Technical data Pos : 14 /Busch-Jaeg er (Neustr uktur)/Modul- Struktur /Online-Dokumentati on/Technische Daten/Di mmer/Technische Daten - 6591 U- 101 @ 23\mod_1333089085280_15.docx @ 207039 @ @ 1
General
Single-wire
clamps 2 x 0.28 mm– 2 x 0.75 mm;
Fine-wire clamps 2 x 0.28 mm – 2 x 0,75 mm;
Bus voltage 20 V DC – 30 V DC
Size 4 TE
Protection IP20
Operating
temperature -25 °C – +55 °C
Size M2306: 90 x 72 x 65 mm
M2307: 216 x 110 x 45 mm
ABB-Welcome
Pos: 15 /Busch-Jaeg er (Neustr uktur)/Modul- Struktur /Online-Dokumentati on/Steuermodul e - Onli ne-D okumentation (--> Für all e D okumente <--)/++++++++++++ Seitenumbruch ++++++++++++ @ 9\mod_1268898668093_0.docx @ 52149 @ @ 1
4 Function Pos : 22 /Busch-Jaeg er (Neustr uktur)/Modul- Struktur /Online-Dokumentati on/Überschriften (--> Für alle D okumente <--)/2. Ebene/G - L/Lastarten @ 20\mod_1326269704379_15.docx @ 136905 @ 2 @ 1
The lift control modules include the M adaptor(M2306) and lift control relay module(M2307),these two devices together make the control ofthe lift only to authorized floor possible. In case the resident presses the "unlock" buttonwhen receiving the guest's call from outdoor station, or the authorized user swipes theregistered card or enters the correct password ,the lift will go down automatically to the floor where installs the outdoor station. Then the lift will go to the dedicated floor where this resident lives, the lift cannot go to other floors even pressing the other floors' button in the lift. The configuration should be done through the dedicated configuration software by connecting the M adaptor with PC/Laptop.
ABB-Welcome
Pos: 30 /Busch-Jaeg er (Neustr uktur)/Modul- Struktur /Online-Dokumentati on/Überschriften (--> Für alle D okumente <--)/1. Ebene/A - F /Anschluss @ 19\mod_1309248278435_15.docx @ 107413 @ 1 @ 1
5 Connection
5.1 M2306 Pos : 31 /Busch-Jaeg er (Neustr uktur)/Modul- Struktur /Online-Dokumentati on/Anschluss/Di mmer /Anschluss - 6591 U-101 @ 23\mod_1333093920008_15.docx @ 207132 @ @ 1
Fig. 1
No. Function
1 Status
- ON = Connected with the system controller / internal bus
- OFF = No connected with the system controller / internal bus
- Blinking = Working with the system controller / internal bus
2 - ON = Power on
- OFF = Power off
- Blinking = Working
3 Connect with M2307
4 Power Supply
5 Connect with the system controller / internal bus
ABB-Welcome
5.2 M2307
5.2.1 Pos : 31 /Busch-Jaeg er (Neustr uktur)/Modul- Struktur /Online-Dokumentati on/Anschluss/Di mmer /Anschluss - 6591 U-101 @ 23\mod_1333093920008_15.docx @ 207132 @ @ 1
Fig. 2
No. Function
1 Power LED
- ON = Power on
- OFF = Power off
2 Setting LED
- Blinks when working normally
3 Address
Set the module address
The address range is 1--16, only the left 4 bits are used
4 Power Supply
5 Connect with M2306
6 Connect with the lift controller
ABB-Welcome
Pos: 24 /Busch-Jaeg er (Neustr uktur)/Modul- Struktur /Online-Dokumentati on/Steuermodul e - Onli ne-D okumentation (--> Für all e D okumente <--)/++++++++++++ Seitenumbruch ++++++++++++ @ 9\mod_1268898668093_0.docx @ 52149 @ @ 1
ABB-Welcome
5.2.2 Lift control relay module address by binary setting
Fig. 3
ABB-Welcome
6 Mounting / Installation Pos : 34 /Busch-Jaeg er (Neustr uktur)/Modul- Struktur /Online-Dokumentati on/Sicherheit (--> Für alle Dokumente <--)/Warnhinweise/Sicherheit - Ni ederspannungs- und 230 V-Leitungen @ 18\mod_1302617821491_15.docx @ 103465 @ @ 1
Warning
Electric voltage!
Risk of death and fire due to electric voltage of 230 V.
– Low-voltage and 230 V cables must not be installed together in a
flush-mounted socket!
In case of a short-circuit there is the danger of a 230 V load on the
low-voltage line.
Pos: 35 /Busch-Jaeg er (Neustr uktur)/Modul- Struktur /Online-Dokumentati on/Sicherheit (--> Für alle Dokumente <--)/Warnhinweise/Sicherheit - Vorgeschaltete Sicherung abschalten @ 20\mod_1326441711467_15.docx @ 137043 @ @ 1
Warning
Electric voltage!
The upstream fuse must be disconnected when working on the lighting
system.
Pos: 36 /Busch-Jaeg er (Neustr uktur)/Modul- Struktur /Online-Dokumentati on/Sicherheit (--> Für alle Dokumente <--)/Warnhinweise/Sicherheit - Fachkenntnisse @ 18\mod_1302774384017_15.docx @ 103564 @ 2 @ 1
6.1 Requirements for the electrician
Warning
Electric voltage!
Install the device only if you have the necessary electrical engineering
knowledge and experience.
• Incorrect installation endangers your life and that of the user of the
electrical system.
• Incorrect installation can cause serious damage to property, e.g. due
to fire.
The minimum necessary expert knowledge and requirements for the
installation are as follows:
• Apply the "five safety rules" (DIN VDE 0105, EN 50110):
1. Disconnect the power;
2. Secure against being reconnected;
3. Ensure there is no voltage;
4. Connect to earth;
5. Cover or barricade adjacent live parts.
ABB-Welcome
• Use suitable personal protective clothing.
• Use only suitable tools and measuring devices.
• Check the type of supply network (TN system, IT system, TT system)
to secure the following power supply conditions (classic connection
to ground, protective earthing, necessary additional measures, etc.).
ABB-Welcome
6.2 Mounting Pos : 38 /Busch-Jaeg er (Neustr uktur)/Modul- Struktur /Online-Dokumentati on/Montage/alle Geräte/Montage - U P-Dosen - D IN 49073- 1 oder geeignetes Aufputzgehaeuse - Ohne D ocvariabl e @ 20\mod_1325766034453_15.docx @ 136593 @ @ 1
The device must only be installed on mounting rails according to DIN EN 50022.
M2306 is highly recommended to install in the lift motor room on the top floor or the
electrical riser; while M2307 is highly recommended to install in the lift cabin.
Fig. 4
Fig. 5: Dismantle
ABB-Welcome
7 User case
7.1 One M2306 and M2307
High building <=16 floors with one Lift
Pos : 41 /Busch-Jaeg er (Neustr uktur)/Modul- Struktur /Online-Dokumentati on/Inbetri ebnahme/Di mmer/Inbetriebnahme - 6591 U-101 @ 19\mod_1311948781023_15.docx @ 108300 @ 222 @ 1
Fig. 6: Topology
Adaptor
ABB-Welcome
Wiring by one M2306 and M2307
Fig. 7
ABB-Welcome
7.2 One M2306 and M2307
High building >16 floors with one Lift
Fig. 8: Topology
Adaptor
ABB-Welcome
Fig. 9
Remarks:
1.The first mini system controller(M2301) feeds M2306 and 1 M2307.
2. Any one more additionalM2307 should be locally powered by 1 mini system controller. Eg.
4 M2307 + 1 M2306, totally, 4 mini system controllers are needed.
ABB-Welcome
7.3 Up to two lifts per building
High building >16 floors
Fig. 10: Topology
Remark: The address code can not be repeated.
Adaptor
ABB-Welcome
7.4 Up to four lifts per building
High building >16 floors
Fig. 11: Topology
Pos: 42 /Busch-Jaeger (Neustruktur)/Modul-Struktur/Online-Dokumentation/Steuermodule - Online-Dokumentation (--> Für alle Dokumente <--)/++++++++++++ Seitenumbruch ++++++++++++ @ 9\mod_1268898668093_0.docx @ 52149 @ @ 1 Remark: The address code can not be repeated.
Adaptor Adaptor
ABB-Welcome
Pos : 43 /Busch-Jaeg er (Neustr uktur)/Modul- Struktur /Online-Dokumentati on/Überschriften (--> Für alle D okumente <--)/1. Ebene/A - F /Bedienung @ 11\mod_1279185541649_15.docx @ 83043 @ 1 @ 1
8 Operation Pos : 44 /Busch-Jaeg er (Neustr uktur)/Modul- Struktur /Online-Dokumentati on/Bedienung/Di mmer/Bedi enung - 6591 U-101 @ 23\mod_1333091293158_15.docx @ 207069 @ @ 1
8.1 User Scenario Illustration of visitor target floor
Fig. 12
Pos: 42 /Busch-Jaeg er (Neustr uktur)/Modul- Struktur /Online-Dokumentati on/Steuermodul e - Onli ne-D okumentation (--> Für all e D okumente <--)/++++++++++++ Seitenumbruch ++++++++++++ @ 9\mod_1268898668093_0.docx @ 52149 @ @ 1
ABB-Welcome
Pos: 43 /Busch-Jaeg er (Neustr uktur)/Modul- Struktur /Online-Dokumentati on/Überschriften (--> Für alle D okumente <--)/1. Ebene/A - F /Bedienung @ 11\mod_1279185541649_15.docx @ 83043 @ 1 @ 1 Pos : 44 /Busch-Jaeg er (Neustr uktur)/Modul- Struktur /Online-Dokumentati on/Bedienung/Di mmer/Bedi enung - 6591 U-101 @ 23\mod_1333091293158_15.docx @ 207069 @ @ 1
8.2 User Scenario Illustration of resident target floor
Fig. 13 Remarks: The lift control module will not function when pressing the unlock button without a call from building outdoor station. Eg. Unlock when there is a villa/floor outdoor station or gate station
ABB-Welcome
9 Configuration through the PC software
9.1 Connected to PC During the configuration, lift control adaptor can be directly connected to PC where the installed PC software (ABB Welcome M PC Configuration Tool) can be used. In another word, no need of local power supply during configuration. Upon finishing the configuration, click “Send the Configuration” to upload the configured file to the system. Refer to general step introduction in following slides. Remarks: Only support Window PC
Fig. 14
ABB-Welcome
9.2 Configuration
Basic Steps Step1: Set basic parameters of the apartment via Welcome M configuration tool
Fig. 15
No. Function
1 Select Building No.
2 Select Floor No.
3 Select Apartment No.
4 Set Physical Add.(eg. 13 means the IS address set by IS switches)
5 Set User Name
6 Set Logic Add.(eg. 0703 means floor no. is 07, and apartment no. is 03 )
7 Add one apartment data to project
8 Upload configuration to system
1 2 3 4
5 6 7 8
ABB-Welcome
Step2: Select Building, M2307 and Configure parameters of each relay
Fig. 16
No. Function
1 Select Building No
2 Select M2307 No.
3 Click “Add” to add a new M2307
4 Select ON or OFF for connecting the Relay
5 Select NO or NC for output type
6 Set Relay operation time(1---3600sec)
7 Show all M2307 parameters Remark: In order to make sure one building is configured properly, for each building, please finish step2, step3, step4, step5 orderly, then start one new this circle for a new building.
1 2 3
4 5 6
7
ABB-Welcome
Step3: Associate OS with M2307
Fig. 17
No. Function
1 Building No.(same as Step2)
2 Select OS No.
3 Select Relay No. of M2307
4 Click “Add” to associate OS with Relay
5 Send all parameters to M2306
6 Input password*(default password:123456)
* please write down this password, if this password is forgotten, reload this
software!
1 2 3
4 5
6
ABB-Welcome
Step4: Associate IS with M2307
Fig. 18
No. Function
1 Building No.(same as Step2)
2 Select IS Physical Add.
3 Select Relay No. of M2307
4 Select OS No.(floor no. of OS installed)
5 Click “Add” to associate IS with Relay
6 Send all parameters to M2306
7 Input password(default password:123456)
1 2 3
5 6 7
4
ABB-Welcome
Optional steps: Step5: Export all data of this project or Import data for new project
Fig. 19
No. Function
1 Export all Lift Control Configuration data to one *.xls(read only)
(Please export the Lift Control Configuration of each building after the
configuration is sent for future use)
2 Import data for a new project from one *.xls
1 2
ABB-Welcome
Step6: Save as one new project
Fig. 20
No. Function
1 Save as one new project: *.xml
1
ABB-Welcome
Step7: Open one existed project data to new OS, Guard Unit and Lift control
Fig. 21
No. Function
1 Open one existed project : *.xml
1