RISK OF FIRE OR ELECTRIC SHOCK. INSTALL THIS KIT ONLY IN THE LUMINAIRES THAT HAVE THE CONSTRUCTION FEATURES AND DIMENSIONS SHOWN IN THE PHOTOGRAPHS AND/OR DRAWINGS.

TO PREVENT WIRING DAMAGE OR ABRASION, DO NOT EXPOSE WIRING TO EDGES OF SHEET METAL OR OTHER SHARP OBJECTS

RISK OF PERSONAL INJURY. THIS EQUIPMENT MAY HAVE SHARP EDGES. WEAR GLOVES TO PREVENT CUTS OR ABRASIONS WHEN REMOVING FROM CARTON, HANDLING AND MAINTAINING THIS EQUIPMENT.

DO NOT MAKE OR ALTER ANY OPEN HOLES IN AN ENCLOSURE OF WIRING OR ELECTRICAL COMPONENTS DURING KIT INSTALLATION.

RISK OF FIRE OR ELECTRIC SHOCK. INSTALLATION OF THIS RETROFIT ASSEMBLY REQUIRES A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE LUMINAIRE’S ELECTRICAL SYSTEM AND THE HAZARD INVOLVED. IF NOT QUALIFIED, DO NOT ATTEMPT INSTALLATION. CONTACT A QUALIFIED ELECTRICIAN.

RETROFIT KIT IS ACCEPTED AS A COMPONENT OF A LUMINAIRE WHERE THE SUITABILITY OF THE COMBINATION SHALL BE DETERMINED BY CSA OR AUTHORITIES HAVING JURISDICTION.

RISK OF FIRE OR ELECTRIC SHOCK. INSTALLATION OF THIS RETROFIT ASSEMBLY REQUIRES A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE LUMINAIRE’S ELECTRICAL SYSTEM AND THE HAZARD INVOLVED. IF NOT QUALIFIED, DO NOT ATTEMPT INSTALLATION. CONTACT A QUALIFIED ELECTRICIAN.

*Deco Digital assumes no responsibility for claims arising out of improper orcareless handling or installation of this product.

WARNING

WARNING

WARNING

WARNING

WARNING

WARNING

WARNING

WARNING

Read all instructions and warnings before attempting installation.RISK OF FIRE OR ELECTRIC SHOCK. LED RETROFIT INSTALLATION REQUIRES KNOWLEDGE OF LUMINAIRES SYSTEMS. IF NOT QUALIFIED, DO NOT ATTEMPT INSTALLATION. CONTACT A QUALIFIED ELECTRICIAN.

ONLY THOSE OPEN HOLES INDICATED IN THE PHOTOGRAPHS AND/OR DRAWINGS MAY BE MADE OR ALTERED AS A RESULT OF KIT INSTALLATION. DO NOT LEAVE ANY OTHER OPEN HOLES IN AN ENCLOSURE OF WIRING OR ELECTRICAL COMPONENTS.

LED Retrofit Kit1x4 2x2 & 2x4

Installation Guide

2

KIT CONTENTS(PARTS LIST)

Standard components of a single kit

Deco’s LED Retrofit Kitsare designed for easy installation. Please refer-ence table to the right to determine your kit con-tents for your install type.

LED Retrofit KitInstallation Guide

1x4 2x2 & 2x4

Installer Notes:

Check your retrofit kit against parts list (page 2).

Disconnect power to fixture. Note: This installation guide pertains to Deco Retrofit Kit install in typical 1’x4’, 2’x2’, and 2’x4’ recessed troffers. Diagrams below show standard fluorescent fixtures (1‘x4’, 2’x2’, and 2’x4’) prior to retrofit (not showing diffuser cover):

12

3

Begin Installation

1.) IMPORTANT: During install, be careful not to touch the LEDs, at the risk of damaging them.2.) When wiring power supply to AC input using the power supply, Green wire attaches to Ground. All other power supplies only have 2 wire AC inputs.3.) A set of labels with model, serial number, and date of manufacture are included in packaging and must be installed in the luminaire once installation is complete. All of these labels must be applied in compliance with UL standards.4.) Install requires application of the Luminaire Modification Label provided in your kit, as per UL. This label includes the statement: “This fixture has been modified and can no longer operate the originally intended lamp.” This label should be applied to troffer housing during installation (Step 17).5.) Sleeving on jumper wires is not reflected in the wiring drawings. Be sure sleeving is in place where sharp edges from the ballast cover may come in contact with the cable.6.) IMPORTANT: Placement of kit components should be thought out and determined prior to surface adherence, to ensure that placement of parts reflects cable lengths.7.) Placement of LINEA-LED Strips in a fixture using a parabolic lens must be carefully determined prior to adherence, so that strips will be placed in the middle of cells to allow maximum light output.

Read all warnings (p. 1) AND Installer Notes (p. 3) before proceeding with retrofit.

Fluorescent FixtureExamples, Before Retrofit:

3

LED Retrofit KitInstallation Guide

1x4 2x2 & 2x4

2x42x2

1x4

4

5

8

6

9

7

Remove ballast cover

USE CLOTH AND CLEANING SOLUTION TO WIPE

BE SURE TO REMOVE ALL DUST, GREASE, ETC &

lamp holders (sockets)

Remove fluorescent tubes (**Dispose of tubes in proper accordance with current state and federal regulation. Fluorescent tubes contain hazardous materials**)

Cut both wires at ballast to the AC

4

Cut the wiring at the lamp holder strips. Do not removelamp holders.

DOWN THE SURFACE OF HOUSING THOROUGHLY

DRY BEFORE PROCEEDING

LED Retrofit KitInstallation Guide

1x4 2x2 & 2x4

cable lengths to ensure all components will be within reach. Carefully press Power Supply on surface of luminaire. · Use a power drill to secure power supply with screws in holes located on supply(ies)

10

11

LED DriverAC

DIA

GRA

M A

Tie (using wire nuts): Black [AC out - Live] to Brown [AC in] White [AC out - Neutral] to Blue [AC in]

Tie (using wire nuts): Green [AC out] to Green [Ground]

Input AC

Ground

AC

in

Connect flying leads from power supply to AC Mains connection (from existing housing) according to diagram A below

5

· Remove cover film from thermal tape on the back of the Power Supply(ies)· When determining where to mount driver, consider provided RED/BLACK jumper

Install Power Supply(ies), securing with the screws provided in the kit:

LED Retrofit KitInstallation Guide

1x4 2x2 & 2x4

Connect power supply to connector board.12

13 14

16

17

Install LINEA-LED Strips :

Connect LED Driver to Dimming Sensor. Run Blue (DIM +) and White (DIM - ) wires from LEDDriver to 0-10V Dimming Sensor, as per Diagram B on page 7.

Run RED/BLACK jumper cables from connector board(s) to Linea-LED. Be sure sleeving is oriented where any sharp edges from the ballast cover may come in contact with the wire.

15

Re-install ballast cover over connector board and power suppl(ied). · Remove cover film from back of thermal tape

· Carefully press the LINEA-LED Strips onto mounting surface. BE SURE NOT TO TOUCH LEDS, AT THE RISK OF DAMAGING THEM.· For installs into fixtures with a parabolic lens, when possible, carefully align strips so that when troffer is closed,strips will be oriented in the middle of the parabolic lens cells.· Secure each individual LED Strip to the housing using 3 screws. Kits should contain 3 screws for each Strip.

Installer must now adhere Luminaire Modification Label to the fixture. Luminaire Label is included in packaging and reads: “This luminaire has been modified and can no longer operate the originally intended lamp.” This step is required by UL standards.

6

LED Retrofit KitInstallation Guide

1x4 2x2 & 2x4

WIRING

INSTRUCTIONS:Power Supply to AC· Tie Brown [AC in] to Black [AC out]· Tie Blue [AC in] to White [AC out]· Tie Red [DC out +] to Red (from Connector Board) · Tie Black [DC out - ] to Black (from Connector Board)· Tie Copper to Green· Tie Green to Ground [screw]

Connector Board to the LINEA-LED Strips· Snap RED/BLACK jumper cables into ports on connector board· Run RED/BLACK jumper cables from board to RTF strips and power supply [DC out], as shown.

BLACK (AC out) Live

WHITE (AC out) Neutral

GREEN Ground

BROWN (AC in) Live

BLUE (AC in) Neutral

RED (DC out) POS (+)

BLACK (DC out) NEG (- )

DC WIRING & DIMMER LEAD SCHEMATIC

DIAG

RAM

B

AC in

DC outblue (DIM + ) white (DIM - )red (+)black (-) to connector

board

0-10VLED DRIVER

Flying Leads Function

7

LED Retrofit KitInstallation Guide

1x4 2x2 & 2x4

8

Wiring Schematic

LED Retrofit KitInstallation Guide

1x4 2x2 & 2x4