Laster Machine Quick Start
Transcript of Laster Machine Quick Start
7/23/2019 Laster Machine Quick Start
http://slidepdf.com/reader/full/laster-machine-quick-start 1/10
GS Laser Machine
Quick operation
Manual
Goldensign International Technology CO,LTD
Catalog
7/23/2019 Laster Machine Quick Start
http://slidepdf.com/reader/full/laster-machine-quick-start 2/10
Hardware setting
PartⅠ:Pull the machine out of the box
PartⅡ:Install the fan
PartⅢ:Install the water-pump
PartⅣ:Adjust the laser head
Software setting
PartⅠ:Install the software
PartⅡ:detail setting
PartⅢ:control panel
Hardware setting
Part Ⅰ
7/23/2019 Laster Machine Quick Start
http://slidepdf.com/reader/full/laster-machine-quick-start 3/10
Open the box, Unplug the board fixed on the botto base ,then
!eo"e the co"er # $ou can see our achine#%here&re two
boxes on the botto base#
Part Ⅱ
'hen (ou first open the wooden box,(ou can see a fan in it#
)ull out the fan , insert the tubes to the fan no**le,+the two
blue tubes are in the plastic box# -asten the etal ring#%hen
arrange the suction outlet to the botto of our achine#
7/23/2019 Laster Machine Quick Start
http://slidepdf.com/reader/full/laster-machine-quick-start 4/10
7/23/2019 Laster Machine Quick Start
http://slidepdf.com/reader/full/laster-machine-quick-start 5/10
Part Ⅲ
Second,open the white box,(ou can see a black water
pup#find the ./pin screw, 'rapped it with the white tape in
the box and fix it to the top of the water pup#0lso, fit 1 sall
tube to it#$ou ust be sure the screw and the sall tube are
sealed#%hen put one side of the tube to the outlet,then fix the
other tube to the inlet #234OU% side ust be correct#
7/23/2019 Laster Machine Quick Start
http://slidepdf.com/reader/full/laster-machine-quick-start 6/10
'hen such things were done,fill the water tank +the white
box with the water#-inall(,fix the plugs of the fan and water
pup to the socket on the left side of the achine#%he
installation process is finished#
%hen it coes to debugging,open the o"er cap of the
achine,cut the package o"er the laser head,then turn on the
power#)ress the 5on6 button,the button is on the right side#$ou
can push the 5reset6 button on the control panel,see whether
the laser head can go to the left side#
7/23/2019 Laster Machine Quick Start
http://slidepdf.com/reader/full/laster-machine-quick-start 7/10
Software setting
Part Ⅰ
7efore install the plung in our C8#7e sure (ou had Corel8raw
software installed#%hen find the 5LaserCorel 9#:#.6 file and
open it#Click the 5Corel9#:#.6 icon,choose 5install6,choose a
language,click 6anual install6 button to finish install#Open
Corel8raw,click 6%ools/Options/;70/8ela( Load ;706,cancel
the hook#
7/23/2019 Laster Machine Quick Start
http://slidepdf.com/reader/full/laster-machine-quick-start 8/10
Part Ⅱ
Now,open the CorelDraw .Draw a picture,click the
“LaserCarve”utton.Doule click the la!er.Like the following
pictures.Choose a "odel,there#re $ "odels %
&utline'Carve.&utline is for cutting "aterials,set the "in
power ,"a( power and speed.Different "aterials have different
speed and power,when !ou have done this, click
“&)”.Second,click “Save” and e(port the file to the *S+ device.
7/23/2019 Laster Machine Quick Start
http://slidepdf.com/reader/full/laster-machine-quick-start 9/10
f co"puter is connectting with the "achine,it "a! need a driver
which is in our CD.Connect the co"puter and the "achine,put the
CD to the CD-&/.t will find the driver and install it auto"aticall!.
n this "ode,!ou should first press 012uip"ent/anage3
utton,then set the port.4ou can set it as 0C&/53,click 0read3 to
send the signal to the "achine,if the singal can e transported to
the "achine,click 0write3 ,otherwise,!ou should reset the
port,"a!e C&/$ or C&/6 or etc.7hen,click
“LaserCarve”utton,click0output3,when !ou see this following
window please choose the port,if !ou have 8ust chosen
“C&/5”,choose “5” in the drop-down "enu,then press “&utput” to
send the file to our "achine directl!.
Part Ⅲ
Put *S+ to our "achine --- click direction ke! to set the laser
head . 9ind a suitale place and click “&rigin” .Click :/1N*:----find
7/23/2019 Laster Machine Quick Start
http://slidepdf.com/reader/full/laster-machine-quick-start 10/10
the file in !our *S+ device---click “1nter”---click the "iddle of the
direction ke!---choose ”No”,this is to test the laser head.----
&),now click the “Start;Pause” utton.7he "achine egin to
cut;Carve.