07.1

0

KH001

INSTRUCTION MANUAL

K-HSZ - Hapa

2

Please keep this manual and product code number for future reference and to order replacement parts if necessary.

● Model Number: K-HSZ

3

● Table of ContentsMODEL NUMBER ............................................... 2GENERAL INSTRUCTIONS .................................... 3INSTALLATION OVER CERAMIC TILES ....................... 3NOTICE ......................................................... 3CARE FOR YOUR FRAMELESS SHOWER DOOR ............. 3CHOICE OF INSTALLATION ................................... 4PARTS LISTING ................................................. 5PROVIDED HARDWARE ........................................ 6TOOLS AND MATERIALS REQUIRED ......................... 7INSTALL THE WALL JAMBS ................................... 8MOUNT THE WALL JAMBS (CONTINUED). ................. 9PANEL INSTALLATION. ....................................... 10MOUNT THE DOOR........................................... 11GASKET INSTALLATION ...................................... 12INSTALL THE SUPPORT BAR. ............................... 13FASTEN UNIT. ................................................. 14INSTALL THE SHELFS. ....................................... 15SILICON SEALING............................................. 16

● General Instructions- Read this manual carefully and completely before proceeding.- It is recommended that you wear safety glasses at all times during the installation.

● Installation over Ceramic Tiles- Silicone should be used to seal the gap where the ceramic tiles meet the panel.- If your shower door is to be installed over ceramic tiles, the tiles should lay completely under the wall jamb.

● Notice- Caulking: no sealant is required inside the shower.- All models are equipped with transparent sealing gaskets.

● Care for your Frameless Shower Door- Never use scouring powder pads or sharp instruments on metal pieces or glass panels. An occasional wiping down with a mild soap diluted in water is all that is needed to keep the panels and aluminum parts looking new.- We recommend wiping the glass panels with a squeegee after each use.

without notice.

4

Choice your door opening: left (1A) or right (1B)1.

1A 1B

CHOICE OF INSTALLATION

1B

Use base : Left Use base : Right

5

1

2

NOTEXX REFERS TO THE MATERIAL FINISH

11- Chrome

PARTS LISTING

4 357

8

14

13

12

10

9

8

16

7

15

6

27

11

6

17

PROVIDED HARDWARE

22

20 21

23 24

18 19

25 26

24A

24B 28

PARTS QTY

1 DOOR PANEL 12 CURVED FIXED PANEL 13 WALL JAMB ‘’A’’ 14 CONNECTOR 15 SUPPORT BAR 16 WALL BRACKET 17 MAGNET GASKET 28 WALL JAMB ‘’B’’ 29 BIG FIXED PANEL 1

10 SMALL FIXED PANEL 111 SHELF 312 SHELF HOLDERS 913 TOWEL BAR 114 BOTTOM DOOR GASKET 115 SET OF HANDLE BAR 116 BASE 117 WALL PLUG 118 WALL PLUG 1219 SCREW 1220 SCREW 421 SCREW 1222 SCREW CAP 1223 ROD 124 PIVOT SUPPORT 225 SCREW 126 KEY 227 SIDE GASKET 128 SCREW 1

7

PENCIL MALLETCUTTING PLIER LEVELTAPE MEASURE

If the shower panels are to be assembled on ceramic tiles, use a 1/4˝ drill bit for ceramic tiles.

DRILL SILICONESCREWDRIVERS 1/4˝& 1/8˝ DRILL BITS

*

*

WOODEN BLOCK

2˝

6˝

1/2˝

TOOLS AND MATERIALS REQUIRED

8

1 INSTALL THE WALL JAMBS

the wall jambs (#3 & #8) on the shower threshold.1A.

Verify wall jambs verticality using a level.

1A

1B

1C

1C.

Trace auter edge of wall jambs.

8

8

3

3

8

8

1A

1A

1A

1/2˝(12.7mm

)

4/3. 11)

mm54. 892(˝

1C

9

2 MOUNT THE WALL JAMBS (CONTINUED).

2A. Reposition the wall jambs ‘‘A’’ (#3) on the shower threshold.

2B. Mark drilling location.

2C. With a 1/4” drill bit, drill 4 holes into the wall using the marks as a guide

2D. Insert 4 wall plugs (#18) and put in each a drop of

silicone.

2E. Secure the wall jamb ‘‘A’’ (#3) using the 1 3/8” screws (#21).

2F. Repeat step 2 for the wall jamb ‘‘B’’(#8).

2A

2B

2C

3

3

2D

2E

3

8

8

16

21

18

2F

10

33

3B.

PANEL INSTALLATION.

2

3B

3B

10

8

8

3

3B

9

24a

3A.and bottom of the panel).Tighten screw (#20) lightlypermit door panel assembly. (only on the top panel).

3A

NOTICE: Position the drain detail of the pivot support (#24) facing the inside of the shower unit.

drain

24b

11

4 MOUNT THE DOOR.

4D

4B.

4C.

Insert the door (#1) into existing pivot support.

1

15

4B

4B

4E

4D.

4E.

Insert the rod (#23) into pivot support (#24).

Install the handle bar (#15) on the door (#1).

1 2

15

23

4C

4A.

4A

27

INTERIOR SHOWER SIDE

27

24a

24b

12

65 GASKET INSTALLATION

5A

6

5D

INTERIOR SHOWER SIDE

5A. and door (#1).

Verify swivelling of door.

5D. Insert bottom gasket (#14) into the door (#1).

5C

19

14

77

9 1

10

5B

7

1

13

6 INSTALL THE SUPPORT BAR.

900

6A

6B

6C

6D4

56

46

56

6E

6F

6A.

Insert connector (#4) into the rod (#23).

6B. Insert temporarely the adjustment bar (#5) intoconnector (#4)

6C. Insert temporarely the wall braket (#6) into adjusting bar (#5).

6D.

Mark drilling location.

6E. Secure the connector (#4).

6F.

Secure the wall bracket (#6).

26

26

6G

2

28

Using a drill bit Ø1/16’’ into the base through the pivot support. Put a bead of silicon inside the hole.

6G.

Remove door panel.

Screw in the provided retainer piece.

Put back door panel.

14

2

19

22

INTERIOR SHOWER SIDE

7A

6867 FASTEN UNIT.

INTERIOR SHOWER SIDE

7A. Assure good relation between two magnetic gaskets (#7), adjusting (if necessary) the support bar( #5).gaskets (#7).

7B

7 1710

5

1922

22

19

9

10

7C

7C. Secure the connector (#4).

5

26

4

15

8 INSTALL THE SHELFS.

8A.panels.(#9,#10).

8C. Tighten the shelf holders.

8D. Install towel bar (#13).

1112

13

8A

8B

8C

8B.

13

9 10

8D 13

16

9 SILICON SEALING.

along the wall jambs’’B’’(#8).

9B

9A

HOURS

2

108

along the wall jambs ‘‘A’’(#3).

3

10

8

2

3