IW EMDBY UM 01 R1.0 REL2.1 Startup Manual

7/25/2019 IW EMDBY UM 01 R1.0 REL2.1 Startup Manual

http://slidepdf.com/reader/full/iw-emdby-um-01-r10-rel21-startup-manual 1/28

User Manual for ULK Start Up

R 2.1

iWave Systems Technologies Pvt. Ltd. of 28(Confidential)

User Manual for ULKiW-EMDBY-UM-01-R1.0

REL2.1_startup

10th

Mar, 2011

Authors Vikrama

APPROVALName Function Organisation Date Signature

Mr. Sebikumar Kuruvilla Wipro

Distribution Mohamed SaliyaAbdullah Khan

Contact InfoName Telephone E-mail

iWave Systems Tech. Pvt. Ltd.7/B, 29th Main,

BTM Layout, 2nd Stage,Bangalore – 560 076, India.

+91-80-2668-3700 (Ext-204)

+91-80-2678-6245 (Ext-204)

[email protected]

DOCUMENT IDENTIFICATION

Project Name iW-EMDBYDocument Name iW-EMDBY-UM-01-R2.1_

startup.docDocument Home //server/emdby/svn/trunk/iW-EMDBY-PF-01-R1.0/iW-EMDBY-SF-01-

R1.0/iW-EMDBY-UM-01-R1.0/iW-EMDBY-UM-01-R1.0-RELx.yz-

ULK/iW-EMDBY-UM-01-R1.0-REL2.1-ULK/iW-EMDBY-UM-01-R1.0-

REL2.1_startup.doc

Revision No Rev 2.1Status FinalAudience Wipro

mailto:[email protected]






R 2.1


DOCUMENT REVISION HISTORY

Revision Date Description Author

1.0 13

t

July 2010 Initial Version Vikrama2.0 10 February

2011Final Version Vikrama

2.1 10t March 2011 Using Xilinx 12.1 Vikrama

PROPRIETARY NOTICE: This document contains proprietary material for the sole use of theintended recipient(s). Do not read this document if you are not the intended recipient. Anyreview, use, distribution or disclosure by others is strictly prohibited. If you are not the intendedrecipient (or authorized to receive for the recipient), you are hereby notified that any disclosure,copying distribution or use of any of the information contained within this document isSTRICTLY PROHIBITED. Thank you. “iWave Systems Tech. Pvt. Ltd.”




R 2.1


Table of Contents

1 INTRODUCTION ........................................................................................................................................ 4

1.1 PURPOSE ................................................................................................................................................ 4

1.2 GLOSSARY ............................................................................................................................................. 4

2 ULK FIRMWARE RECOVERY AND UPDATING ............. ............. ............. ............. ............ ............. ..... 5

2.1 IDENTIFYING SD MMC CARD DRIVE NAME ............................................................................................ 5

3 BOOT MODE SEQUENCES ...................................................................................................................... 8

3.1 R ECOVERY MODE FOR U-BOOT ............................................................................................................... 8

3.2 R ECOVERY MODE FOR LINUX IMAGE ...................................................................................................... 9

3.3 NAND MODE WITH SD CARD................................................................................................................... 9

3.4 NAND MODE WITHOUT SD CARD .......................................................................................................... 10

4

MAKING U-BOOT AND LINUX SD CARD ............ ............. ............. ............. ............. ............. ............. .. 11

4.1 FIRMWARE R ECOVERY ......................................................................................................................... 11

4.2 FIRMWARE UPDATING .......................................................................................................................... 11

4.3 LINUX SD CARD ................................................................................................................................... 11

4.4 LINUX IMAGE RECOVERY WITH ONE ARGUMENT .................................................................................... 11

4.5 LINUX IMAGE RECOVERY WITH THREE ARGUMENTS ............................................................................... 11

5 XILINX INSTALLATION GUIDE ........................................................................................................... 12

6 XILINX FREE LICENSE .......................................................................................................................... 18

7 UPDATING XILINX LICENSE................................................................................................................ 24

8

DO’S & DON’TS........................................................................................................................................ 27

9 FOR YOUR INFORMATION ................................................................................................................... 28




R 2.1


1 Introduction

1.1 Purpose

The purpose of this document is to explain the procedure to ULK firmware recovery and ULK

firmware updating.

1.2 Glossary

Table 1: Glossary

Acronyms Description

CD Compact Disk

MMC Multi Media Card

PC Personal Computer

SD Secure Digital

USB Universal Serial Bus




R 2.1


2 ULK Firmware Recovery and Updating

2.1 Identifying SD MMC Card Drive Name

Step 1: Connect the SD card to the card reader and connect this card reader to the Linux PC

Step 2:

Go to System>Administrator>Disk Utility

Below window will appears after clicking the “Disk Utility”




R 2.1


Step 3:

Click on “USB 2.0 SD MMC Reader” and you will get the information about the SD card

SD card drive name will be there as shown in below figure (e g: /dev/sdc )




R 2.1


Note:

If SD card is corrupted then follow the “Making U- boot and Linux SD card” to create theSD card

If the Flash is corrupted the do the “Recovery Mode” else “Nand mode”




R 2.1


3 Boot Mode Sequences

3.1 Recovery Mode for U-boot

Step 1: Select the Recovery mode from the “DIP SWITCH FOR PROCESSOR BOOT” as

shown in the figure

Step 2: Insert the SD card having u-boot firmware

Step 3: Set the toggle switch to “LAB OPERATING MODE” (EXPERT MODE)




R 2.1


Step 4: Power on the board and on the switch shown below

3.2 Recovery Mode for Linux Image

Step 1: Select the Recovery mode from the “DIP SWITCH FOR PROCESSOR BOOT”

Ref: 3.1, Step 1

Step 2: Insert the SD card having Linux recovery image


Ref: 3.1, Step 3


Ref: 3.1, Step 4

3.3 Nand Mode with SD card

Step 1: Select the Recovery mode from the “DIP SWITCH FOR PROCESSOR BOOT” as

shown in the figure




R 2.1



Ref: 3.1, Step 3


Ref: 3.1, Step 4

Step 4: If SD card present in the slot then it will search for Linux image otherwise user have to press a key to stop the Linux booting

3.4

Nand Mode without SD cardStep 1: Select the Recovery mode from the “DIP SWITCH FOR PROCESSOR BOOT”

Ref: 3.3, Step 1

Step 2: Set the toggle switch to “LAB OPERATING MODE”(EXPERT MODE)

Ref: 3.1, Step 3

Step 3: Power on the board and on the switch shown below and u-boot prompt will appear withinfew seconds

Ref: 3.1, Step 4




R 2.1


4 Making U-boot and Linux SD card

4.1 Firmware Recovery

Execute the following commands to recover the ULK firmware

#ulk-recovery.sh <arg1 - driver name>

E g: ulk-recovery.sh /dev/sdc

4.2 Firmware Updating

Execute the following commands to update the ULK firmware

#ulk-firmware-update.sh <arg1 - driver name> <arg2 - Firmware update file path>

E g: ulk-recovery.sh /dev/sdb /ulk/Firmware-update

4.3 Linux SD card

There are two methods to make a Linux SD card.

Linux image recovery with one argument

Linux image recovery with three arguments

4.4 Linux image recovery with one argument

Execute the following commands to make the Linux SD card#ulk-linux-create.sh <arg1 - driver name>

E g: ulk-recovery.sh /dev/sdb

4.5 Linux image recovery with three arguments

Execute the following commands to make the Linux SD card#ulk-linux-create.sh <arg1 - driver name> <arg2 - uImage and u-boot firmware path> <arg3- Linux root file system path>

E g: ulk-recovery.sh /dev/sdb /home/test/Desktop/ULK-Release1.0/ULK-DEV-FROM/Linux-SD-card/ /home/test/Desktop/ULK-Release1.0/ULK-DEV-FROM/Linux-SD-card/

Note: In this uImage-v-1-0.bin and ulk-firmware-v-1-0.tar.gz should be in same folder.




R 2.1


5 Xilinx Installation Guide

Note: While running the install.sh script it will ask for Xilinx installation. Please follow the stepsas shown in the figures

Step1: Starting of Xilinx installation

Step 2: Press “Next” continue




R 2.1


Step 3: Click “I accept the terms of this software license” and give “Next”




R 2.1


Step 4: Select “ISE WebPACK ” and give “Next”

Step 5: Select “Acquire or Manage a License Key” and give “Next”




R 2.1


Step 6: give “Next”

Step 7: Click “Install” button




R 2.1


Step 8: Click “Finish” button




R 2.1


Step 8: Click “OK ”

Step 9: Click “Close” button




R 2.1


6 Xilinx Free License

Link to create a Xilinx account: www.xilinx.com/getlicense

Step 1: Create an account, refer the below figure

Note: Don’t create an account if you already have

Step 2: Fill the mandatory field to create an account, refer the below figure

http://www.xilinx.com/getlicense.






R 2.1


Step 3: Sign in using a created account




R 2.1


Step 4: To get the license, fill the mandatory fields

Step 5: Select “ISE Design Suite: WebPack License”, refer the below figure




R 2.1


Step 6: Click on “Generate Node-Locked License”, refer the below figure

Step 7: Select “ISE Design Suite: WebPack License”. Click on “Next”, refer the below figure




R 2.1


Step 7: Click on “Next”, refer the below figure




R 2.1


Step 7: License will be sent as e-mail.

Step 8: Select “Logout”




R 2.1


7 Updating Xilinx License

Copy the license to the PC, Please follow the steps

Step 1: Run the Xilinx

E.g.: $xilinx

Open the terminal and type Xilinx

Ste p 2: Select “OK ”




R 2.1


Step 3: Select “Manage Xilinx License”.

Step 4: Click on “Copy License”




R 2.1


Step 5: Browse the license file from your system as shown in the below figure

Step 5: Click “OK ” and Click “Close”




R 2.1


8 Do’s & Don’ts

During testing, only top wooden enclosure has to be removed & keep the board on

bottom wooden enclosure.

It is recommended to use the supplied cables / accessories along with the kit. If differentcables / mating connectors are used, ensure to use the compatible ones.

Use only the 5V power supply adaptor that has been provided along with the kit.

Providing different voltage could damage the board.

Don’t insert the power cable when the power switch is in ON position.

The devices used in the board are sensitive to ESD. To prevent ESD, don’t touch any ICs

or external connectors with bare hand. Ensure to have ESD protection in the lab. Use the

ESD protective wrist strap when connecting the accessories to the board.

Power off the board before connecting the speakers at J15 & J17 connectors.

For good speaker output quality, connect speakers with the following specification: “720

mW/Ch Into 8 Ω”.

Power off the board before connecting any external modules.

For ADC, analog signal ranging from 0 to 2V max. can be applied. Applying more than2V signal may damage the board.

While using J2 connector, pin no. 5 & 8 of switch SW11 should be in OFF position. AlsoJ13 connector should not be used at the same time.

While using J3 connector, all the pins of switch SW11 should be in OFF position. Also J8& J13 connector should not be used at the same time.

While using J8 connector, all the pins of switch SW11 should be in OFF position. Also J3& J13 connector should not be used at the same time.

While using J13 connector, pin no. 8 of switch SW11 should be in ON position rest all pins of switch SW11 should be in OFF position. Also J3 & J8 connector should not beused at the same time.

LCD is pasted to the acrylic. Do not try to remove the LCD or the LCD connectingcable.

As LCD surface is prone for physical damage, handle it carefully and ensure that noforeign object falls on it & no load is applied to that. Use only the stylus for touchoperation.




R 2.1

Ensure that no foreign materials falls inside the board as it could damage the board

electrically / physically

Do not close the Control Panel while doing the operations on ULK board. If user close

the ULK control Panel then restart the ULK board.

Once the connection is established, do the “Disconnect” before closing the ULK Control

Panel. If user close the ULK control Panel then restart the ULK board.

9 For Your Information

Maximum scan time will be 60Sec

o

Eg: If only one board is connected, but user selected the ULK count as 2 thenscan will take 60Sec and it will find only one ULK board

IW EMDBY UM 01 R1.0 REL2.1 Startup Manual

Documents

Transcript of IW EMDBY UM 01 R1.0 REL2.1 Startup Manual