ITO Catalog
3
Material composition Made from Chrysolite Asbestos Fiber with Synthetic Elastomers and Inorganic fillers. Applications: To seal off most transmission and hydraulic fluids, refrigerating oils, motor oils, carburetor ,fuel mixtures steam ,water /antifreeze & water /anti corrosion mixtures alkalis & solvents. Standard Sheet Size 1500×2000 mm,1500×4000 mm,1500×1500 mm, 1500×4500 mm,1500×3000 mm, 2000×3000 mm Tolerance Thickness 1 mm = ± 0.10 mm Length ± 50 mm >1mm = ± 0.10% width ± 50 mm Material data General information Material type Compressed Asbestos Fiber (CAF) Non Metallic Range Temperature limit 560 °C Internal Pressure limit 160 bar Specification compliance DIN: 3754 IT-O Thickness (mm) 0.6 – 6 Color Grey/Graphited Physical properties Standard Unit Value Density DIN 28090-2 [gm/cm³] 1.8-2.0 Tensile Strength (a) Across (b) Across DIN 3754 ISI:2712-1999 [N/MM²] [N/MM²] >16 >26 Compressibility DIN 3754 [%] 5 -15 Recovery DIN 3754 [%] >40 Immersion in I R M 903 oil DIN 3754 (a) Thickness Increase [%] <15 (b) Mass Increase [%] <20 Immersion in ASTM fuel B ISI:2712/1998 (a) Thickness Increase [%] <20 (b) Mass Increase [%] <15 Ignition Loss DIN 52911 [%] <26 NOTE: ALL INFORMATION AND RECOMMENDATIONS GIVEN IN THIS BROCHURE ARE CORRECT TO THE BEST OF OUR KNOWLEDGE. SINCE CONDITIONS OF USE ARE BEYOND OUR CONTROL THE INFORMATION PROVIDED AND ONLY SERVE AS A GUIDELINE. USERS MUST SATISFY THOSE SELVES THAT PRODUCTS ARE SUITABLE FOR THE INTENDED PROCESS AND USES. WE RESERVE THE RIGHT TO CHANGE PRODUCT DESIGN AND PROPERTIES WITHOUT NOTICE. An ISO /TS 1694:2009 certified company
Transcript of ITO Catalog
Material composition Made from Chrysolite Asbestos Fiber with Synthetic Elastomers and Inorganic fillers.
Applications: To seal off most transmission and hydraulic fluids, refrigerating oils, motor oils, carburetor ,fuel mixtures steam ,water /antifreeze & water /anti corrosion mixtures alkalis & solvents.
Standard Sheet Size 1500×2000 mm,1500×4000 mm,1500×1500 mm,
1500×4500 mm,1500×3000 mm, 2000×3000 mm
Tolerance Thickness 1 mm = ± 0.10 mm Length ± 50 mm >1mm = ± 0.10% width ± 50 mm
Material data
General information
Material type Compressed Asbestos Fiber (CAF) Non Metallic Range
Temperature limit 560 °C
Internal Pressure limit 160 bar
Specification compliance DIN: 3754 IT-O
Thickness (mm) 0.6 – 6
Color Grey/Graphited
Physical properties Standard Unit Value
Density DIN 28090-2 [gm/cm³] 1.8-2.0
Tensile Strength
(a) Across (b) Across
DIN 3754
ISI:2712-1999
[N/MM²] [N/MM²]
>16 >26
Compressibility DIN 3754 [%] 5 -15
Recovery DIN 3754 [%] >40
Immersion in I R M 903 oil DIN 3754
(a) Thickness Increase
[%] <15
(b) Mass Increase [%] <20
Immersion in ASTM fuel B ISI:2712/1998
(a) Thickness Increase
[%] <20
(b) Mass Increase [%] <15
Ignition Loss DIN 52911 [%] <26
NOTE:
ALL INFORMATION AND RECOMMENDATIONS GIVEN IN THIS BROCHURE ARE CORRECT TO THE BEST OF OUR KNOWLEDGE. SINCE
CONDITIONS OF USE ARE BEYOND OUR CONTROL THE INFORMATION PROVIDED AND ONLY SERVE AS A GUIDELINE. USERS MUST
SATISFY THOSE SELVES THAT PRODUCTS ARE SUITABLE FOR THE INTENDED PROCESS AND USES. WE RESERVE THE RIGHT TO CHANGE
PRODUCT DESIGN AND PROPERTIES WITHOUT NOTICE.
An ISO /TS 1694:2009 certified company
Chemical compatibility chart
== RReeccoommmmeennddeedd
== SSuuiittaabbiilliittyy ddeeppeennddss oonn cciirrccuummssttaanncceess
== NNoott rreeccoommmmeennddeedd
Acetates Dichloride benzene Isobutyl alcohol Picric acid
Acetic acid Diesel Oil Kerosene Potassium chloride
Acetic Aldehyde Diethyl glycol Lactic acid Potassium chloride
Acetic Anhydride Diethyl ether Isopropyl alcohol Potassium cyanide
Acetone Dioxin Lead acetate Potassium hydroxide
Acrylic acid Dipentene Linseed oils Potassium sulfate
Alcohols Diphenyl Lubricating oil Producer gas
Aldehydes Electrolyte Mercury chloride Propane
Alum Essential oil Methanol Propyl alcohol
Ammonia Ethane Methyl chloride Pyridine
Ammonium salts Ethanol diamine Methyl ethyl ketone Sea water
Benzaldeyde Ether Methylene chloride Silver nitrate
Benzene Ethyl benzene Motor Oil Sodium carbonate
Bromine Ethyl bromide Mustard Sodium chloride
Butyl alcohol Ethyl chloride Naphtclene ZD Sodium sulfate
Calcium chloride Ethylene Naphta Sodium sulfide
Carbolic acid Ferric chloride Naphtalene Sinning sulfide
Carbon disulfide Ethylene diamine Natural Gas Spinning solutions
Carbon monoxide Ethylene glycol Nickel Chloride Steam
Caster oil Fatty acids Nitrobenzene Stearic acid
Caustic potash Flue gases
Nitric acid (Conc.) Sulfur dioxide
Benzoic acid Formaldehyde Nitrogen Sulfur acid (Conc.)
Chlorinated water Formic acid Nitrogen oxides Sulfurous acid
Chloro benzene Freon Oxygen up to 40 bar Tar
Chloroform Fuel acid Ozone Tar oil
Chromic acid Gelatin Palmitic acid
Tartaric acid
Critic acid Glycol Paraffin Tetra line
Coal gas Hexane Petrol Toluene
Coconut oil Hydraulic (Mineral Oil) Petroleum Transformer oil
Crude oil HCI acid (Conc.) Phenol Transmission fluid
Cyclohexanole Hydrogen Phenol ether Turpentine
Cyclohexanone Hydrogen bromide Phenythdrazine Vegetable oil
Dibenzyl ether Hydrogen sulfide Phosphoric acid Xylene
