ISOLATION RELAY - PSA Products · 30V DC @ 5 Amps Contact Switching ... Operating Temperature 0°...
1
1300 772 776 [email protected] psaproducts.com.au FIRE • SECURITY • INTERCOMS FEATURES: • Isolation relay for Lifesaver smoke, heat and CO alarms for connection to auxiliary devices such as sirens, sounders, emergency lights, security and fire panels. • Operates in absence of mains voltage and only when alarm device is in alarm state. • Selectable relay options; latching, pulse and CO latching mode. • 240V AC / 30V DC 5Amp contact rating • Normally Open and Normally Close contact options • When CO latching mode is selected, only CO alarm activation will trigger the isolation relay. SPECIFICATIONS Operating Coil Voltage 5V - 10V DC Secondary Contacts Normally Open Normally Closed (change-over contacts) Contact options Pulse, Latching, CO Latching Secondary Contact Rating 240V AC 50Hz @ 5 Amps 30V DC @ 5 Amps Contact Switching Time Delay 4 seconds once activated Maximum No. of interconnected smoke alarms to a single LIFSAIR unit 24 Maximum number of LIFSAIR relay connected to one smoke alarm 3 Operating Temperature 0° – 50°C Dimensions 89mm Deep x 68mm Wide x 45mm High Compatible with PSA’s complete range of smoke alarms, heat alarms and carbon monoxide alarm. ISOLATION RELAY MODEL LIFSAIR *Refer to Installation and User Manual for further information. Due to PSA commitment to continual product improvement, specification may change without notice. LIFSAIR LIFSAIR Connection to Auxiliary Devices 1. Secondary Contacts NO and NC are activated by smoke alarm interconnect switch wire. 2. Contacts are rated 240V AC 5Amps LIFSAIR Connection to Auxiliary Devices using 9V output from smoke alarm LIFSAIR By installing the LIFSAIR in this manner it will allow you to operate such devices such as sirens, strobes, bells, lights, fans, magnetic locks or any devices which do not exceed 240VAC @ 5Amps. SIRENS, SOUNDERS, LOCKS, FANS AND SECURITY SYSTEM AND AUXILIARY DEVICES. Lifesaver 5800 series Smoke Alarms
Transcript of ISOLATION RELAY - PSA Products · 30V DC @ 5 Amps Contact Switching ... Operating Temperature 0°...
-
1300 772 776 [email protected] psaproducts.com.au
F I R E • S E C U R I T Y • I N T E R C O M S
FEATURES:• Isolation relay for Lifesaver smoke, heat and
CO alarms for connection to auxiliary devices such as sirens, sounders, emergency lights, security and fire panels.
• Operates in absence of mains voltage and only when alarm device is in alarm state.
• Selectable relay options; latching, pulse and CO latching mode.
• 240V AC / 30V DC 5Amp contact rating
• Normally Open and Normally Close contact options
• When CO latching mode is selected, only CO alarm activation will trigger the isolation relay.
SPECIFICATIONS
Operating Coil Voltage 5V - 10V DC
Secondary Contacts
Normally OpenNormally Closed
(change-over contacts)
Contact options Pulse, Latching, CO Latching
Secondary ContactRating
240V AC 50Hz @ 5 Amps30V DC @ 5 Amps
Contact SwitchingTime Delay 4 seconds once activated
Maximum No. ofinterconnectedsmoke alarms to asingle LIFSAIR unit
24
Maximum number of LIFSAIR relay connected to one smoke alarm
3
OperatingTemperature 0° – 50°C
Dimensions89mm Deep
x 68mm Widex 45mm High
Compatible with PSA’s complete range of smoke alarms, heat alarms and carbon monoxide alarm.
ISOLATION RELAYMODEL LIFSAIR
*Refer to Installation and User Manual for further information. Due to PSA commitment to continual product improvement, specification may change without notice.
LIFSAIR
LIFSAIR Connection to Auxiliary Devices
1. Secondary Contacts NO and NC are activated by smoke alarm interconnect switch wire.
2. Contacts are rated 240V AC 5Amps
LIFSAIR Connection to Auxiliary Devices using 9V output from
smoke alarm
LIFSAIR
By installing the LIFSAIR in this manner it will allow you to operate such devices such as sirens, strobes, bells, lights, fans, magnetic locks or any devices which do not exceed 240VAC @ 5Amps.
SIRENS, SOUNDERS, LOCKS, FANS AND SECURITY SYSTEM AND AUXILIARY DEVICES.
Lifesaver 5800 series Smoke Alarms
![Initial Eligibility Clearinghouse Process Initial ... · school graduation date of the PSA’s class [as determined by the first year of enrollment in high school (ninth grade)].](https://static.fdocuments.us/doc/165x107/5f0af0647e708231d42e1557/initial-eligibility-clearinghouse-process-initial-school-graduation-date-of.jpg)
