Instruction of Product Manual Index of Technical Data Sheet. … · 2014. 5. 5. · roswan qd hb...
Transcript of Instruction of Product Manual Index of Technical Data Sheet. … · 2014. 5. 5. · roswan qd hb...
* Please click on an above Index which you want to see.
Version 04Issued April 2007
5 Index of Technical Data Sheet. Product name S - U
3 Index of Technical Data Sheet. Product name E - N
4 Index of Technical Data Sheet. Product name N - S
Index of Technical Data Sheet. Product name A - E
1
2
Instruction of Product Manual
Click Here toNext page
Instruction for this Product Manual
1. Please click the section to refer to
click click
2. To return to the front page, please click the logo on the top of the Data
Sheet index page.
3. To return to the Data Sheet index page, please click the logo on the top
of the Product Data Sheet pages.
Version Information The Technical Data Sheet are edited as of April 2007 and these information are subject to revision
from time to time wishout any notice.
For the latest information please contact CMP.
Version 04Issued April 2007
Click Here toFront Page
Click Here toNext Page
TECHNICAL DATA (alphabetical)PRODUCT NAME DATA SHEET No.*Please click the Product name for the technical data sheet.
AJJ
BA
BANNOH 200BANNOH 2000 QDBANNOH 2000BANNOH 500BANNOH 500 ACBANNOH 500 NBANNOH 500QDBANNOH 500RBIOCLEAN DXBIOCRYSTY 700BIOCRYSTY ANZENBIOGUARD C-3 ABISCON AFBISCON HB-NT L ABISCON HB-NT L QD BBITUMEN SOLUTION BBONDET PUTTY
C
AABA
C
E
R
Version 04Issued April 2007
EPICON T-500 FOR REPAIR
EPICON MARINE CHEPICON MARINE HBEPICON MARINE UNDERCOAT MEPICON T-500
CMP BIOCLEAN HBCMP BIOCLEAN SEALERCOAT
CLEANKEEP 201CLEANKEEP 5000CLEANKEEP 5000 HOLDING PRIMERCLEANKEEP 5500
CERABESTCERABOND 2000CERABOND TUCERABOND TU QL
60256025
607259825983
10356073
ACRI 700 FINISH JACRI 700 PRIMER JALP 500
BANNOH 200 QD
540954025301
60726075
805210491034
613584409050
8279828556106135
5056507259418283
5082505550515073
5006
40384037
512751275083
Click Here toPrevious Page
Click Here toNext Page
TECHNICAL DATA (alphabetical)PRODUCT NAME DATA SHEET No.*Please click the Product name for the technical data sheet.
E
A
A
QPA
G
H
L
A
MAB
S
N
A
IHFG
Version 04Issued April 2007
EPICON T-800 HOLDING PRIMER
ETCHING PRIMER H ( for Peller Clean Set Jr)ETCHING PRIMER H ( for Peller Clean Set)EVAMARINEEVAMAX 100P
6037
60326020
603560331034103510611061106124006435
62406250
4005
210021042107
21075876589559686437
589758966180618061816181618161816181
EPICON T-500 HSEPICON T-500 PRIMER HEPICON T-800
EPICON T-800 HSEPICON ZINC RICH PRIMER B-2EPICON ZINC RICH PRIMER B-2 QLETCHING PRIMER H
GALBON SPGALBON S-HB
HIPER AC
LZI PRIMERLZI PRIMER ZR-HBLZI PRIMER ZS HB
MARINE STAR 10 KAIMARINE STAR 20 KAIMARINE STAR AMARINE STAR FLAT SMAXSTOP G
NEW MARINE GOLD DXNEW MARINE GOLDNOVA 1000NOVA 1000 QD
NOVA 2000 GF
NOVA 2000NOVA 2000 CH QDNOVA 2000 CHNOVA 2000 GF QD
Click Here toPrevious Page
Click Here toNext Page
TECHNICAL DATA (alphabetical)PRODUCT NAME DATA SHEET No.*Please click the Product name for the technical data sheet.
NAD
A
PA
R
SNNNNM
M
P
Version 04Issued April 2007
RAVAX AF
ROSWAN QD HB
SEA GRANDPRIX 500 M
SEA GRANDPRIX 1000
SEA GRANDPRIX 300SEA GRANDPRIX 330SEA GRANDPRIX 500
SEA GRANDPRIX 2000
SEA FRONTIER F
SEA GRANDPRIX CF SUPER NFD
SEA GRANDPRIX 800SEA GRANDPRIX CF MK IISEA GRANDPRIX CF MK II LSEA GRANDPRIX CF SUPER
SEA FRONTIER HSEA FRONTIER SSEA FRONTIER ME
RUST INHIBITIVE OIL "CK"RUST INHIBITIVE PRIMER Z
SEA FRONTIER
ROSWAN QD
ROSWAN QD ZR HBROSWAN QD ZS HB
RAVAX FINISHRAVAX PRIMERRAVAX AC HB
59215971
NOVA 2000 QDNOVA 2000 W QDNOVA 5000
NZ PRIMER S
PERMAX No. 3000 S W
5905591258305831
5911590159025905
5919592159175909
59175922
2134213682502110
4001401021302131
44004100
6050605760593040
1050
6050
6182
61816181
6182NOVA 5000 BARRIER
PERMAX No. 3000 SPERMAX No. 3000 MUPERMAX No. 3000 MU WPOLIBI T-1
Click Here toPrevious Page
Click Here toNext Page
TECHNICAL DATA (alphabetical)PRODUCT NAME DATA SHEET No.*Please click the Product name for the technical data sheet.
SKL
T
G
U
WA
Version 04Issued April 2007
SILVAX SQ-M
UMEGUARD PU-TUUMEGUARD PU
SILICON HR SILVERSILICON HRSILVA SPAR No. 500
SEA GRANDPRIX CF-10SEA GRANDPRIX CF-10 L
UMEGUARD SX HS QDUNY MARINE
6135
6165
UMEGUARD SUPUR H
TFA FLATTFA-10
UMEGUARD SUPER H PRIMERUMEGUARD SUPER-H PRIMER QDUMEGUARD SXUMEGUARD SX HS
SEA GRANDPRIX CF-10 L M
SEA GRANDPRIX CF-20
SEAJET 033
5510
61966166
SILVAX SQ-K
6193
616461976195
58735865
30073008
8035803480338000
9121912491308032
5919592391029114
5928
59175917
5927
SILICON HR SILVER HG
SEA GRANDPRIX CF-10 M
SEAJET 132SEAJET 137SEAJET 145WSILICON HR PRIMER
SEA GRANDPRIX FRPSEAJET 015
Click Here toPrevious Page
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
ACRI 700 FINISH J(ACR 700 FC J)
Feb.2006
No. 4038J
ACRI 700 FINISH J is a finishing coat based on acrylic resin and drying by evaporation of the solvents. It has excellent adhesion property, weathering resistance and gloss and colour retention.
TECHNICAL DATA
Type Acrylic finish paint
Recommened
Use
Finishing coat on ships' topside, superstructure
Color : White, As specified Flash Point : 24.0 [degC] Solid by volume : 40 (+-2) [volume %] VOC : 545 [g/L] Coverage(Theoretical): 0.075 - 0.1 [L/m
2
]
Information
Film Thickness : WET 75 - 100 [micron]DRY 30 - 40 [micron]
(D.F.T. 35micron) 5 oC 10 oC 20 oC 30 oC
Drying Time Surface Dry 1.5hrs. 1hr. 30mins. 30mins.Hard Dry 8hrs. 7hrs. 6hrs. 4hrs.
Painting Interval Min 10hrs. 8hrs. 7hrs. 5hrs.Max - - - -
Method of Application : Airless spray; Brush; Roller Weather : Temperature : Minimum 0
degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : (Fc#4)60[sec]
Tip No. : (GRACO)719 Paint Output Pressuer: 11.7 - 14.7[MPa] Spray Speed : 60 - 80[cm/sec]
Thinner : RAVAX THINNER, Thinning: 0 - 6 % by Volume
Preceding Coats : ACRI 700 PRIMER, BANNOH 200, BANNOH 500, BISCON HBNT-L
Conditionof
Application
Subsequent Coats : -
Packaging One pack product
Notes VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
ACRI 700 PRIMER J(ACR 700 P J)
Feb.2006
No. 4037J
ACRI 700 PRIMER J is an effective anti-rust primer based on acrylic resin and drying by evaporation of the solvents.It can be applied directly to bare steel or existing paint film such as acrylic, chlorinated rubber and epoxy. It has also good workability and it is possible to obtain thick coat especially by spray application.
TECHNICAL DATA
Type Acrylic anti-rust primer
Recommened
Use
Anti-rust primer for exposure parts
Color : Light gray Flash Point : 24.0 [degC] Solid by volume : 43 (+-2) [volume %] VOC : 492 [g/L] Coverage(Theoretical): 0.093 - 0.186 [L/m
2
]
Information
Film Thickness : WET 93 - 186 [micron]DRY 40 - 80 [micron]
(D.F.T. 60micron) 5 oC 10 oC 20 oC 30 oC
Drying Time Surface Dry 1.5hrs. 1.2hrs. 1hr. 30mins.Hard Dry 12hrs. 9hrs. 7hrs. 6hrs.
Painting Interval Min 18hrs. 13hrs. 9hrs. 7hrs.Max - - - -
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum 0
degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : (Fc#4)120[sec]
Tip No. : (GRACO)721,723 Paint Output Pressuer: 11.7 - 17.7[MPa] Spray Speed : 60 - 80[cm/sec]
Thinner : RAVAX THINNER, Thinning: 0 - 10 % by Volume
Preceding Coats : NZ PRIMER, WELBOND, EPICON ZINC RICH PRIMER, CERABOND, etc.
Conditionof
Application
Subsequent Coats : ACRI 700 FINISH J
Packaging One pack product
Notes VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
ALP 500(ALP 500)
Mar.2006
No. 5006
ALP 500 is used as epoxy primer for aluminum on ship's hull, superstructure and other parts. It is a highly effective paint system with excellent adhesion property on aluminum surfaces, and has excellent salt water resistance and excellent applicability , high build efficiency.
TECHNICAL DATA
Type Epoxy paint
Recommened
Use
As a primer on aluminum
Mixing Ratio : Color :
Base : Hardener = 66 : 34 [by volume]Light gray
Flash Point : Base = 22.5, Hardener = 26.5 [degC] Solid by volume : 58 (+-2) [volume %] VOC : 410 [g/L] Coverage(Theoretical): 0.086 - 0.216 [L/m
2
]
Information
Film Thickness : WET 86 - 216 [micron]DRY 50 - 125 [micron]
() 5 oC 10 oC 20 oC 30 oC
Drying Time Surface Dry 3.5hrs. 2.5hrs. 1.5hrs. 1hr.Hard Dry 38hrs. 28hrs. 16hrs. 12hrs.
Painting Interval Min 24hrs. 18hrs. 10hrs. 8hrs.Max * - - - -
Pot Life 24hrs. 18hrs. 12hrs. 8hrs.
Method of Application : Airless spray, Brush Weather : Temperature : Minimum 5
degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : (Fc#4)170[sec]
Tip No. : (GRACO)719,721 Paint Output Pressuer: 14.7 - 17.7[MPa] Spray Speed : 60 - 80[cm/sec]
Thinner : EPICON MARINE THINNER, Thinning: 0 - 10 % by Volume
Preceding Coats : -
Conditionof
Application
Subsequent Coats : UNY MARINE, VINYL AC-HB, etc.
Packaging Two pack product
Notes 1.* Please refer to the painting specifications.2.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
BANNOH 200 QD(B 200 QD)
Feb.2006
No. 5127A
BANNOH 200 QD, based on a combination of modified epoxy resin and rust-preventive pigment, has excellent adhesion property, toughness and effective rust-preventive property. It is suitable for protection of superstructures and exposed deck of steel ships, and suitable for the application at cold weather.
TECHNICAL DATA
Type Modified epoxy rust-preventive paint, high-build
Recommened
Use
Primer on inside and outside of superstructures, exposed deck of steel ships and other steel structures
Mixing Ratio : Color :
Base : Hardener = 76 : 24 [by volume]White, Grey, Green
Flash Point : Base = 23.7, Hardener = 27.0 [degC] Solid by volume : [volume %] VOC : 415 [g/L] Coverage(Theoretical): 0.085 - 0.339 [L/m
2
]
Information
Film Thickness : WET 85 - 339 [micron]DRY 50 - 200 [micron]
(D.F.T. 200micron) 5 oC 10 oC 20 oC 30 oC
Drying Time Surface Dry 3hrs. 2hrs. 1hr.Hard Dry 20hrs. 16hrs. 10hrs.
Painting Interval Min 16hrs. 12hrs. 8hrs.Max * - - -
Pot Life 8hrs. 7hrs. 4hrs.
Method of Application : Airless spray; Brush Weather : Temperature : Minimum 5
degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 1 - 1.5Pa・s
Tip No. : (GRACO)719,721 Paint Output Pressuer: 14.7 - 17.7[MPa] Spray Speed : 60 - 80[cm/sec]
Thinner : EPICON MARINE THINNER, Thinning: 0 - 5 % by Volume
Preceding Coats : CERABOND, EPICON ZINC RICH PRIMER, etc.
Conditionof
Application
Subsequent Coats : EPICON MARINE HB, UNY MARINE, RAVAX FINISH, etc.,
Packaging Two pack product
Notes 1.* Please refer to the painting specifications.2.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
BANNOH 200(B 200)
Feb.2006
No. 5127
BANNOH 200, based on a combination of modified epoxy resin and rust-preventive pigment, has excellent adhesion property, toughness and effective rust-preventive property. It is suitable for protection of superstructures and exposed deck of steel ships.
TECHNICAL DATA
Type Modified epoxy rust-preventive paint, high-build
Recommened
Use
Primer on inside and outside of superstructures, exposed deck of steel ships and other steel structures
Mixing Ratio : Color :
Base : Hardener = 76 : 24 [by volume]White, Grey, Light grey, N8
Flash Point : Base = 23.7, Hardener = 27.0 [degC] Solid by volume : 59 (+-2) [volume %] VOC : 419 [g/L] Coverage(Theoretical): 0.085 - 0.339 [L/m
2
]
Information
Film Thickness : WET 85 - 339 [micron]DRY 50 - 200 [micron]
(D.F.T. 200micron) 5 oC 10 oC 20 oC 30 oC
Drying Time Surface Dry 3.5hrs. 2.5hrs. 1.5hrs. 1hr.Hard Dry 30hrs. 22hrs. 12hrs. 10hrs.
Painting Interval Min 24hrs. 18hrs. 10hrs. 8hrs.Max * - - - -
Pot Life 18hrs. 14hrs. 7hrs. 4hrs.
Method of Application : Airless spray, Brush Weather : Temperature : Minimum 5
degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 1 - 1.5Pa・s
Tip No. : (GRACO)719,721 Paint Output Pressuer: 14.7 - 17.7[MPa] Spray Speed : 60 - 80[cm/sec]
Thinner : EPICON MARINE THINNER, Thinning: 0 - 5 % by Volume
Preceding Coats : CERABOND, EPICON ZINC RICH PRIMER, etc.
Conditionof
Application
Subsequent Coats : EVAMARINE, RAVAX FINISH, ACRI 700 FINISH, UNY MARINE, EPICON MARINE HB, POLIBI T-1, etc.
Packaging Two pack product
Notes 1.* Please refer to the painting specifications.2.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
BANNOH 2000 QD(B2000 QD)
Jul.2006
No. 5083
BANNOH 2000 QD, is a multi-purpose high solid epoxy primer, which gives excellent physical properties such as toughness, abrasion resistance and adhesion, etc., and has excellent flexibility, resistance to sea water and cathodic protection. It is suitable for most of areas of ship as Universal primer.
TECHNICAL DATA
Type Polyamine adduct cured epoxy
Recommened
Use
Anti-corrosive paint for ship's hull, exposed decks, superstructures and ballast water tanks, etc.
Mixing Ratio : Color :
Base : Hardener = 75 : 25 [by volume]Pink, Light grey
Flash Point : Base = 32.5, Hardener = 27.0 [degC] Solid by volume : 80 (+-2) [volume %] VOC : 244 [g/L] Coverage(Theoretical): 0.125 - 0.312 [L/m
2
]
Information
Film Thickness : WET 125 - 312 [micron]DRY 100 - 250 [micron]
(D.F.T. 200micron) 5 oC 10 oC 20 oC 30 oC
Drying Time Surface Dry 7hrs. 4hrs. 1hr.Hard Dry 17hrs. 10hrs. 5hrs.
Painting Interval Min 17hrs. 10hrs. 5hrs.Max * * *
Pot Life 6hrs. 4hrs. 2hrs.
Method of Application : Airless spray, Brush Weather : Temperature : Minimum 5
degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 1.5 - 2.0Pa・s
Tip No. : (GRACO)621,623 Paint Output Pressuer: 14.7 - 17.7[MPa] Spray Speed : 60 - 80[cm/sec]
Thinner : EPICON MARINE THINNNER, Thinning: 0 - 7 % by Volume
Preceding Coats : CERABOND, EPICON ZINC RICH PRIMER, etc.
Conditionof
Application
Subsequent Coats : BANNOH 500 N, UNYMARINE, EPICON MARINE HB, etc.
Packaging Two pack product
Notes VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
BANNOH 2000(B2000)
Jul.2006
No. 5082
BANNOH 2000, is a multi-purpose high solid epoxy primer, which gives excellent physical properties such as toughness, abrasion resistance and adhesion, etc., and has excellent flexibility, resistance to sea water and cathodic protection. It is suitable for most of areas of ship as Universal primer.
TECHNICAL DATA
Type Polyamine adduct cured epoxy
Recommened
Use
Anti-corrosive paint for ship's hull, exposed decks, superstructures and ballast water tanks, etc.
Mixing Ratio : Color :
Base : Hardener = 75 : 25 [by volume]Pink, Light grey
Flash Point : Base = 32.5, Hardener = 27.0 [degC] Solid by volume : 80 (+-2) [volume %] VOC : 261 [g/L] Coverage(Theoretical): 0.125 - 0.312 [L/m
2
]
Information
Film Thickness : WET 125 - 312 [micron]DRY 100 - 250 [micron]
(D.F.T. 200micron) 5 oC 10 oC 20 oC 30 oC
Drying Time Surface Dry 10hrs. 8hrs. 3hrs. 1hr.Hard Dry 28hrs. 20hrs. 10hrs. 5hrs.
Painting Interval Min 28hrs. 20hrs. 10hrs. 5hrs.Max * * * *
Pot Life 8hrs. 6hrs. 3hrs. 1.5hrs.
Method of Application : Airless spray, Brush Weather : Temperature : Minimum 5
degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 1.5 - 2.0Pa・s
Tip No. : (GRACO)621,623 Paint Output Pressuer: 14.7 - 17.7[MPa] Spray Speed : 60 - 80[cm/sec]
Thinner : EPICON MARINE THINNNER, Thinning: 0 - 7 % by Volume
Preceding Coats : CERABOND, EPICON ZINC RICH PRIMER, etc.
Conditionof
Application
Subsequent Coats : BANNOH 500 N, UNYMARINE, EPICON MARINE HB, etc.
Packaging Two pack product
Notes VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
BANNOH 500(B 500)
Feb.2006
No. 5055
BANNOH 500, is a multi-purpose primer,which gives excellent physical properties such as toughness, abrasion resistance and adhesion, etc., and has excellent flexibility, resistance to sea water and cathodic protection.It is suitable for most areas of ship.
TECHNICAL DATA
Type Epoxy paint
Recommened
Use
Anti-corrosive paint for ship's hull, exposed decks, superstructures and ballast water tanks, etc.
Mixing Ratio : Color :
Base : Hardener = 81 : 19 [by volume]Grey, Light Grey, Red brown, Black
Flash Point : Base = 23.1, Hardener = 24.9 [degC] Solid by volume : 63 (+-2) [volume %] VOC : 401 [g/L] Coverage(Theoretical): 0.16 - 0.32 [L/m
2
]
Information
Film Thickness : WET 159 - 317 [micron]DRY 100 - 200 [micron]
(D.F.T. 200micron) 5 oC 10 oC 20 oC 30 oC
Drying Time Surface Dry 7hrs. 5.5hrs. 4hrs. 2.5hrs.Hard Dry 24hrs. 18hrs. 10hrs. 8hrs.
Painting Interval Min 24hrs. 18hrs. 10hrs. 8hrs.Max * * * *
Pot Life 18hrs. 14hrs. 7hrs. 4hrs.
Method of Application : Airless spray, Brush Weather : Temperature : Minimum 5
degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 1.6 - 2Pa・s
Tip No. : (GRACO)621,623 Paint Output Pressuer: 14.7 - 17.7[MPa] Spray Speed : 60 - 80[cm/sec]
Thinner : EPICON MARINE THINNER, BANNOH THINNERThinning: 0 - 15 % by Volume
Preceding Coats : CERABOND, EPICON ZINC RICH PRIMER, etc.
Conditionof
Application
Subsequent Coats : BANNOH 500 N, BANNOH 500 AC, SILVAX SQ-K.M, EPICON MARINE HB
Packaging Two pack product
Notes 1.* Kindly consult with CMP sales office.2. In confined spaces such as tank insides or low temperature condition, ventilation is required during application and curing to removed solvent vapours and promote curing.3.Waiting time before the first cargo loading Temp. 10degC 20degC 30degC (Days) 18 10 64.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
BANNOH 500 AC(B 500 AC)
Mar.2007
No. 5051
BANNOH 500 AC, is Tar free ,multi-purpose primer, based on special epoxy resin and pigmentation. It gives excellent physical properties such as toughness and abrasion resistance, adhesion, etc. and highly resistant to water, and salt water. It is suitable for outside hull ,deck and superstructure of ships.
TECHNICAL DATA
Type Tar free epoxy paint
Recommened
Use
Anti-corrosive for ships, and also where anti-abrasive property is specially required.
Mixing Ratio : Color :
Base : Hardener = 78 : 22 [by volume]Grey, Red brown
Flash Point : Base = 23.1, Hardener = 24.9 [degC] Solid by volume : 65 (+-2) [volume %] VOC : 382 [g/L] Coverage(Theoretical): 0.16 - 0.31 [L/m
2
]
Information
Film Thickness : WET 154 - 308 [micron]DRY 100 - 200 [micron]
(D.F.T. 200micron) 5 oC 10 oC 20 oC 30 oC
Drying Time Surface Dry 7hrs. 5.5hrs. 4hrs. 2.5hrs.Hard Dry 24hrs. 18hrs. 10hrs. 8hrs.
Painting Interval Min (urethaen)
24hrs.(30)
18hrs.(24)
10hrs.(16)
8hrs.(11)
Max * - - - -Pot Life 18hrs. 14hrs. 7hrs. 4hrs.
Method of Application : Airless spray, Brush Weather : Temperature : Minimum 5
degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 1.6 - 2Pa・s
Tip No. : (GRACO)621,623 Paint Output Pressuer: 14.7 - 17.7[MPa] Spray Speed : 60 - 80[cm/sec]
Thinner : EPICON MARINE THINNER, Thinning: 0 - 5 % by Volume
Preceding Coats : CERABOND, EPICON ZINC RICH PRIMER, BANNOH 500, etc.
Conditionof
Application
Subsequent Coats : SILVAX SQ-K.M, EPICON MARINE HB, etc.
Packaging Two pack product
Notes 1.* Please refer to the painting specifications.2.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
BANNOH 500 N(B 500 N)
Feb.2006
No. 5073
BANNOH 500 N, is Tar free ,epoxy anti-corrosive primer, based on epoxy resin and pigmentation. It gives excellent physical properties such as toughness and abrasion resistance, adhesion, especially excellent adhesion with anti-fouling paint.
TECHNICAL DATA
Type Epoxy paint
Recommened
Use
Anti-corrosive paint for ship's bottom
Mixing Ratio : Color :
Base : Hardener = 85 : 15 [by volume]Plum
Flash Point : Base = 21.2, Hardener = 22.7 [degC] Solid by volume : 54 (+-2) [volume %] VOC : 444 [g/L] Coverage(Theoretical): 0.18 [L/m
2
]
Information
Film Thickness : WET 185 [micron]DRY 100 [micron]
(D.F.T. 100micron) -5 oC 0 oC 5 oC 10 oC 20 oC 30 oC
Drying Time Surface Dry 10hrs. 7hrs. 5hrs. 4hrs. 3hrs. 2hrs.Hard Dry 48hrs. 28hrs. 18hrs. 15hrs. 8hrs. 6hrs.
Painting Interval Min 48hrs. 28hrs. 18hrs. 15hrs. 8hrs. 6hrs.Max * - - - - - -
Pot Life - - 18hrs. 14hrs. 7hrs. 4hrs.
Method of Application : Airless spray, Brush Weather : Temperature : Minimum -5
degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 1.6 - 2.0 Pa・s
Tip No. : (GRACO)621,623 Paint Output Pressuer: 14.7 - 17.7[MPa] Spray Speed : 60 - 80[cm/sec]
Thinner : EPICON MARINE THINNER, Thinning: 0 - 10 % by Volume
Preceding Coats : BANNOH 500
Conditionof
Application
Subsequent Coats : SEA GRANDPRIX 1000,2000 , etc.
Packaging Two pack product
Notes 1.* Please refer to the painting specifications.2.Application at temperatures down to -5 degC is possible but curing to hardness takes longer and complete cure will be reached when temperature increases.3.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
BANNOH 500 QD(B 500 QD)
Jul.2006
No. 5056
BANNOH 500 QD, is a multi-purpose primer,which gives excellent physical properties such as toughness, abrasion resistance and adhesion, etc., and has excellent flexibility, resistance to sea water and cathodic protection. It is suitable for most areas of ship. It is suitable for the application at cold weather.
TECHNICAL DATA
Type Epoxy paint
Recommened
Use
Anti-corrosive paint for ship's hull, exposed decks, superstructures and ballast water tanks, etc.
Mixing Ratio : Color :
Base : Hardener = 81 : 19 [by volume]Grey, Ligt Grey, Red brown, Black
Flash Point : Base = 23.1, Hardener = 24.9 [degC] Solid by volume : 63 (+-2) [volume %] VOC : 394 [g/L] Coverage(Theoretical): 0.16 - 0.32 [L/m
2
]
Information
Film Thickness : WET 159 - 317 [micron]DRY 100 - 200 [micron]
(D.F.T. 200micron) -5 oC 0 oC 5 oC 10 oC 20 oC 30 oC
Drying Time Surface Dry 10hrs. 7hrs. 5hrs. 4.5hrs. 3hrs.Hard Dry 36hrs. 24hrs. 17hrs. 13hrs. 8hrs.
Painting Interval Min 36hrs. 24hrs. 17hrs. 13hrs. 8hrs.Max * * * * *
Pot Life 6hrs. 5hrs.
Method of Application : Airless spray, Brush Weather : Temperature : Minimum -5
degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 1.6 - 2Pa・s
Tip No. : (GRACO)621,623 Paint Output Pressuer: 14.7 - 17.7[MPa] Spray Speed : 60 - 80[cm/sec]
Thinner : EPICON MARINE THINNER, Thinning: 0 - 15 % by Volume
Preceding Coats : CERABOND, EPICON ZINC RICH PRIMER, etc.
Conditionof
Application
Subsequent Coats : BANNOH 500 N, SILVAX SQ-K.M, EPICON MARINE HB, etc.
Packaging Two pack product
Notes 1.* Kindly consult with CMP sales office.2. In confined spaces such as tank insides or low temperature condition, ventilation is required during application and curing to removed solvent vapours and promote curing.3.Application at temperatures down to -5 degC is possible but curing to hardness takes longer and complete cure will be reached when temperature increases.4.Waiting time before the first cargo loading Temp. 5degC 10degC 20degC (Days) 25 16 105.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
BANNOH 500 R(B 500 R)
Feb.2006
No. 5072
BANNOH 500 R, is Tar free ,epoxy anti-corrosive primer, based on epoxy resin and pigmentation. It gives excellent physical properties such as toughness and abrasion resistance, adhesion, especially excellent adhesion with anti-fouling paint. It is suitable for outside hull, deck and superstructure of ships.
TECHNICAL DATA
Type Epoxy paint
Recommened
Use
Anti-corrosive paint for repar ships
Mixing Ratio : Color :
Base : Hardener = 85 : 15 [by volume]Grey
Flash Point : Base = 22, Hardener = 23.5 [degC] Solid by volume : 60 (+-2) [volume %] VOC : 390 [g/L] Coverage(Theoretical): 0.12 - 0.29 [L/m
2
]
Information
Film Thickness : WET 125 - 292 [micron]DRY 75 - 175 [micron]
(D.F.T. 175micron) 5 oC 10 oC 20 oC 30 oC
Drying Time Surface Dry 5hrs. 4hrs. 3hrs. 2hrs.Hard Dry 24hrs. 20hrs. 10hrs. 8hrs.
Painting Interval Min * - - - -Max * - - - -
Pot Life 18hrs. 14hrs. 7hrs. 4hrs.
Method of Application : Airless spray; Brush Weather : Temperature : Minimum 5
degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 1.6 - 2.0Pa・s
Tip No. : (GRACO)423,425,427 Paint Output Pressuer: 14.7 - 17.7[MPa] Spray Speed : 60 - 80[cm/sec]
Thinner : EPICON MARINE THINNER, BANNOH THINNERThinning: 0 - 5 % by Volume
Preceding Coats : EPICON ZINC RICH PRIMER, etc.
Conditionof
Application
Subsequent Coats : SEA GRANDPRIX 1000,2000 , RAVAX FINISH, EPICON MARINE FINISH, etc.
Packaging Two pack product
Notes 1.* Please refer to the painting specifications.2.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
BIOCLEAN DX ()
Feb.2006
No. 5941
BIOCLEAN DX is an innocuous long life anti-fouling paint to prevent attachment of marine organisms by the effect of low critical surface tension of the surface of coated film. It has the following advantages: 1. Environmentaliy friendly, safe and hygienic 2. Good anti-fouling property 3. Easy application
TECHNICAL DATA
Type Special synthetic resin anti-fouling coating with an outstanding long term durability
Recommened
Use
Anti-fouling for propeller of ship
Color : Clear Flash Point : 26.0 [degC] Solid by volume : 84 (+-2) [volume %] VOC : 130 [g/L] Coverage(Theoretical): 0.088 [L/m
2
]
Information
Film Thickness : WET 89 [micron]DRY 75 [micron]
() 5 oC 10 oC 20 oC 30 oC
Drying Time Surface Dry 45mins. 30mins. 20mins. 15mins.Hard Dry 10hrs. 7hrs. 5hrs. 4hrs.
Painting Interval Min 10hrs. 7hrs. 5hrs. 4hrs.Max 5days 5days 5days 5days
Dry to Launch Min 11hrs. 8hrs. 6hrs. 5hrs.
Method of Application : Airless spray, Brush Weather : Temperature : Minimum 0
degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 70 - 80[sec]
Tip No. : (GRACO)617,719 Paint Output Pressuer: 11.7 - 14.7[MPa] Spray Speed : 60 - 80[cm/sec]
Thinner : SILICON THINNER, Thinning: 0 - 5 % by Volume
Preceding Coats : ETCHING PRIMER H
Conditionof
Application
Subsequent Coats :
Packaging One pack product
Notes VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
BIOCRYSTY 700(BIOCRYSTY 700)
Feb.2006
No. 8283
BIOCRYSTY 700 is a epochal anti-foulant for firming fishnet specially designed for the prevention of sticking barnacle and mussel moss animals with a cuprous glass type anti-foulant which developed by Chugoku Marin Paints originally. Specific FeaturesGood anti-fouling property : Expecting the stabilized anti-fouling property for over 3 months in spite of slight difference with the sea or seasons.Good workability and drying property for net-dyeing.No bad smelling, only solvent smell.Easy handling : Because of using high flexibility resin, there is no stiffening on fishnet after dyeing and handles easily.
TECHNICAL DATA
Type Copper type anti-fouling paint
Recommened
Use
Fishnet
Color : Dark brown Flash Point : 26.0 [degC] Specific Gravity : 1.02(+-0.05) [g/mL] VOC : 704 [g/L] Thinner : BIOCRYSTY THINNER Consumption : about 44 - 54 % (against fishnet weight) Weight Increase : 12 - 16 % (Dry)
Information
Packaging One pack product
Notes VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
BIOCRYSTY ANZEN(ANZEN)
Feb.2006
No. 8279
BIOCRYSTY ANZEN is a epochal anti-foulant for firming fishnet specially designed for the prevention of sticking barnacle and mussel moss animals with a cuprous glass type anti-foulant which developed by Chugoku Marin Paints originally. Specific FeaturesGood anti-fouling property : Expecting the stabilized anti-fouling property for over 3 months in spite of slight difference with the sea or seasons.Good workability and drying property for net-dyeing.No bad smelling, only solvent smell.Easy handling : Because of using high flexibility resin, there is no stiffening on fishnet after dyeing and handles easily.
TECHNICAL DATA
Type cuprous glass type anti-fouling paint
Recommened
Use
Fishnet
Color : Dark brown Flash Point : 31.5 [degC] Specific Gravity : 1.07(+-0.05) [g/mL] VOC : 762 [g/L] Drying Time : 20 degC / 3 hrs. Thinner : BIOCRYSTY THINNER Consumption : about 70 - 80 % (against fishnet weight) Weight Increase : 20 - 30 %
Information
Packaging One pack product
Notes VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
BIOGUARD C-3(C-3)
Jan.2006
No. 8285A
BIOGUARD C-3 is a epochal anti-foulant for fishnet specially designed for the prevention of sticking hydrozoan with a organic nitorogenous sulfur type anti-foulant which developed by Chugoku Marin Paints originally. Specific FeaturesGood anti-fouling property : Expecting the stabilized anti-fouling property for over 3 months in spite of slight difference with the sea or seasons.Good workability and drying property for net-dyeing.No bad smelling, only solvent smell.Easy handling : Because of using high flexibility resin, there is no stiffening on fishnet after dyeing and handles easily.
TECHNICAL DATA
Type Organic nitrogenous sulfur type anti-fouling paint
Recommened
Use
Fishnet
Color : Black, White, Orange, Flash Point : 26.0 [degC] Specific Gravity : 0.96(+-0.05) [g/mL] VOC : 658 [g/L] Drying Time : 20 degC / 3 hrs. Thinner : BIOGUARD THINNER, Consumption : about 30 - 35 % (against fishnet weight) Weight Increase : 9 - 10 % (Dry)
Information
Packaging One pack product
Notes VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
BISCON AF(BC AF)
Mar.2006
No. 5610
BISCON AF is a synthetic rubber vehicle based anti-fouling paint with a high content of antifoulant. It provides very effective and extended protection against fouling and results in fuel saving and elimination of lost time as well as loss of speed usually resulting from fouling.
TECHNICAL DATA
Type Synthetic rubber anti-fouling paint
Recommened
Use
Anti-fouling finish of steel ship's bottom and underwater areas
Color : Red brown Flash Point : 27.0 [degC] Solid by volume : 53 (+-2) [volume %] VOC : 404 [g/L] Coverage(Theoretical): 0.075 - 0.094 [L/m
2
]
Information
Film Thickness : WET 75 - 94 [micron]DRY 40 - 50 [micron]
() 5 oC 10 oC 20 oC 30 oC
Drying Time Surface Dry 1hr. 45mins. 30mins. 20mins.Hard Dry 6hrs. 4.5hrs. 3hrs. 2hrs.
Painting Interval Min 11hrs. 8hrs. 5hrs. 4hrs.Max - - - -
Dry to Launch Min 12hrs. 9hrs. 6hrs. 5hrs.
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum 0
degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : (Fc#4)80[sec]
Tip No. : (GRACO)619,721 Paint Output Pressuer: 11.7 - 14.7[MPa] Spray Speed : 60 - 80[cm/sec]
Thinner : BISCON AF THINNER, Thinning: 0 - 5 % by Volume
Preceding Coats : RAVAX AC, RAVAX AC-HB, RAVAX AC S-HB, SILVAX SQ-HB, etc.
Conditionof
Application
Subsequent Coats : -
Packaging One pack product
Notes 1.There is a risk of antifoulings becoming fouled when ships are stationary for three consecutive weeks or more,particularly in areas with a high risk of fouling.2.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
BISCON HB-NT L (BC HB NT L)
Feb.2006
No. 6135A
BISCON HB-NT L, is a epoxy type paint. It gives excellent physical properties such as adhesion, toughness and abrasion resistance, etc. and chemical resistance to water, salt water and crude oil.
TECHNICAL DATA
Type Epoxy type paint
Recommened
Use
Cargo hold, Inside and outside of accommodation space, Void space, Cofferdam, Engine room, Pipe line, Other steel structures, etc.
Mixing Ratio : Color :
Base : Hardener = 85 : 15 [by volume]Grey, Black, White, Red brown, Green
Flash Point : Base = 23.5, Hardener = 19.0 [degC] Solid by volume : 57 (+-2) [volume %] VOC : 426 [g/L] Coverage(Theoretical): 0.176 - 0.439 [L/m
2
]
Information
Film Thickness : WET 176 - 439 [micron]DRY 100 - 250 [micron]
(D.F.T. 250micron) 5 oC 10 oC 20 oC 30 oC
Drying Time Surface Dry 4.5hrs. 3.5hrs. 2.5hrs. 1.5hrs.Hard Dry 44hrs. 27hrs. 17hrs. 12hrs.
Painting Interval Min 44hrs. 27hrs. 17hrs. 12hrs.Max - - - -
Pot Life 24hrs. 14hrs. 8hrs. 5hrs.
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum 5
degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 1.5 - 2.0 Pa・s
Tip No. : (GRACO)623 Paint Output Pressuer: 14.7 - 17.7[MPa] Spray Speed : 60 - 80[cm/sec]
Thinner : BISCON THINNER, Thinning: 0 - 5 % by Volume
Preceding Coats : WELBOND, CERABOND, NZ PRIMER, EPICON ZINC RICH PRIMER
Conditionof
Application
Subsequent Coats : -
Packaging Two pack product
Notes 1.In confined spaces such as tank insides, ventilation is required during application and curing to remove solvent vapours and promote curing.2.Waiting time before the first dry cargo loading Temp. 10degC 20degC 30degC (Days) 20 12 73.As nature of epoxy coatings Biscon HB-NT L can not avoid chalking and fading on UV exposure.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
BISCON HB-NT L QD(BC HB NT L QD)
Feb.2006
No. 6135B
BISCON HB-NT L QD, is a epoxy type paint. It gives excellent physical properties such as adhesion , toughness and abrasion resistance, etc. and chemical resistance to water, salt water and crude oil. In addition , it has excellent drying properties at low temperatures.
TECHNICAL DATA
Type Epoxy type paint
Recommened
Use
Cargo hold, Inside and outside of accomdation space, Void space, Cofferdam, Engine room, Pipe line, Other steel structures, etc.
Mixing Ratio : Color :
Base : Hardener = 85 : 15 [by volume]Grey, Black, White, Red brown
Flash Point : Base = 23.5, Hardener = 19.0 [degC] Solid by volume : 57 (+-2) [volume %] VOC : 435 [g/L] Coverage(Theoretical): 0.176 - 0.439 [L/m
2
]
Information
Film Thickness : WET 176 - 439 [micron]DRY 100 - 250 [micron]
(D.F.T. 250micron) -5 oC 0 oC 5 oC 10 oC 20 oC 30 oC
Drying Time Surface Dry 8hrs. 5hrs. 2.5hrs. 2hrs. 1.5hrs.Hard Dry 40hrs. 33hrs. 20hrs. 16hrs. 14hrs.
Painting Interval Min 40hrs. 33hrs. 20hrs. 16hrs. 14hrs.Max - - - - -
Pot Life 20hrs. 12hrs. 6hrs.
Method of Application : Airless spray, Brush, Roller Weather : Temperature : -5 - 20
degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 1.5 - 2.0Pa・s
Tip No. : (GRACO)623 Paint Output Pressuer: 14.7 - 17.7[MPa] Spray Speed : 60 - 80[cm/sec]
Thinner : BISCON THINNER, Thinning: 0 - 15 % by Volume
Preceding Coats : WELBOND, CERABOND, NZ PRIMER, EPICON ZINC RICH PRIMER
Conditionof
Application
Subsequent Coats : -
Packaging Two pack product
Notes 1. In confined spaces such as tank insides or low temperature condition, ventilation is required during application and curing to removed solvent vapours and promote curing.2.The temperature of the mixed base and hardener preferably should be above 10 degC otherwise extra solvent may be required to obtain appliaction viscosity.3.Too much solvent results in reduced sag resistance and paint film property.4.Application at temperatures down to -5 degC is possible but curing to hardeness takes longer and complete cure will be reached when temperature increases.5.Waiting time before the first cargo loading Temp. 5degC 10degC 20degC (Days) 25 16 10
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
6.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
BITUMEN SOLUTION B(BS B)
Feb.2007
No. 8440
BITUMEN SOLUTION B is a bituminous paint which has excellent adhesion properties to steel plates. BITUMEN SOLUTION B is used as a primer for Liquid Bitumen Enamel, and may be applied by itself as a temporary anti-corrosive paint.
TECHNICAL DATA
Type Bituminous paint
Recommened
Use
As a protective coating for steel structures and inside of rudders, etc.
Color : Black Flash Point : 31.0 [degC] Solid by volume : 41 [volume %] VOC : 499 [g/L] Coverage(Theoretical): 0.073 - 0.121 [L/m
2
]
Information
Film Thickness : WET 73 - 121 [micron]DRY 30 - 50 [micron]
() 5 oC 10 oC 20 oC 30 oC
Drying Time Surface Dry 2hrs. 1.5hrs. 1hr. 30mins.Hard Dry 6hrs. 5hrs. 3hrs. 2hrs.
Painting Interval Min 6hrs. 5hrs. 3hrs. 2hrs.Max - - - -
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum 0
degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 0.7Pa・s
Tip No. : (GRACO)515,517 Paint Output Pressuer: 11.7 - 14.7[MPa] Spray Speed : 60 - 80[cm/sec]
Thinner : MARINE THINNER, Thinning: 0 - 5 % by Volume
Preceding Coats : EVABOND, WELBOND, CERABOND, NZ PRIMER, EPICON ZINC RICH PRIMER
Conditionof
Application
Subsequent Coats : -
Packaging One pack product
Notes VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
BONDET PUTTY(BP)
Feb.2006
No. 9050
BONDET PUTTY, based on epoxy resin and polyamide resin combination, has excellent physical properties such as adhesion, impact and abrasion resistance, etc., and chemical resistance to salt water, oil, alkalis and dilute acid, and is suitable for putty of tank interiors and underwater areas.
TECHNICAL DATA
Type Epoxy/Polyamide putty
Recommened
Use
As protective coating against galvanic corrosion around the anode, and touching up of pitting corrosion occurring on exterior hull and tank inside.
Mixing Ratio : Color :
Base : Hardener = 64 : 36 [by volume]Grey
Flash Point : Base = -, Hardener = - [degC] Solid by volume : 100 [volume %] VOC : 0 [g/L] Coverage(Theoretical): 2 [L/m
2
]
Information
Film Thickness : WET 2000 [micron]DRY 2000 [micron]
() 5 oC 10 oC 20 oC 30 oC
Drying Time Surface Dry 7hrs. 5hrs. 3hrs. 2hrs.Hard Dry 26hrs. 18hrs. 8hrs. 5hrs.
Painting Interval Min 14hrs. 10hrs. 6hrs. 4hrs.Max 10days 7days 4days 2days
Pot Life 8hrs. 6hrs. 3hrs. 2hrs.
Method of Application : Spatula Weather : Temperature : Minimum 5
degC, Humidity : Maximum 85 %R.H. Thinner : EPICON MARINE THINNER (For cleaning),
Thinning: - % by Volume Preceding Coats : -
Conditionof
Application
Subsequent Coats : Epoxy paint
Packaging Two pack product
Notes VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
CERABEST(Cb)
Sep.2006
No. 8052
CERABEST is a combination of strictly selected heat resistant alloys and heat resistant silicate solution. It has excellent heat resistance at high temperatures up to 800 degC, and has excellent adhesion to inorganic zinc shop primer.
TECHNICAL DATA
Type Ultra heat resistant paint
Recommened
Use
As a topcoat of inorganic shop primer to prevent from the heat damages of steel structures, such as Ships' super structures.
Mixing Ratio : Color :
Paste : Base = 44 : 56 [by volume]Grey
Flash Point : Paste = 13.6, Base = 13.0 [degC] Solid by volume : 45 [volume %] VOC : 553 [g/L] Coverage(Theoretical): 0.071 [L/m
2
]
Information
Film Thickness : DRY 30 [micron]
(D.F.T. 30micron) 5 oC 10 oC 20 oC 30 oC
Drying Time Surface Dry 12mins. 8mins. 4mins. 2mins.Hard Dry 60hrs. 48hrs. 30hrs. 15hrs.
Painting Interval Min Organic 14days 10days 7days 7daysMax 180days 180days 180days 180days
Pot Life 30hrs. 24hrs. 16hrs. 10hrs.
Method of Application : Airless spray, Air spray Weather : Temperature : 5 - 35
degC, Humidity : 50 - 90 %R.H. For Airless Spray : Viscosity : (IWATA CUP)9 - 10[sec]
Tip No. : (GRACO)619,719 Paint Output Pressuer: 8.8 - 11.8[MPa] Spray Speed : 30 - 50[cm/sec]
Thinner : INORGANIC SHOP PRIMER THINNER, INORGANIC SHOP PRIMER THINNER SThinning: 0 - 5 % by Volume
Preceding Coats : inorganic shop primer
Conditionof
Application
Subsequent Coats : Epoxy paint, Tar-epoxy paint, Non-tar-epoxy paint, Chlorinated rubber primer, Alkyd primer
Packaging Two pack product
Notes 1.To obtain homogenous mixture stir the PASTE well prior to adding the BASE.2.To prevent from nozzle clogging, put 80 mesh filter on the suction inlet. 3.To prevent from pigment settling, keep stirring the mixture during the application. 4.Since the paint mixture reacts with moisture, use up the mixture as soon as possible under high humid condition.5.Use the specified thinner.6.Take 7 days for aging before application of subsequent coat at below 10 degree C since curing of the product becomes considerably slow at low temperature.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
CERABOND 2000 (CB 2000)
Mar.2007
No. 1049A
CERABOND 2000 is a combination of heat resistant alloy and heat resistant silicate solution producing an inorganic rust preventive coat mechanically adhered to the steel and giving an effective and long-term protection against corrosion without suffering from blistering and loss of adhesion. It is compatible with organic overcoatings as well as with inorganic overcoatings. CERABOND 2000 is extremely resistant to heat (up to 800 degree C) and secondary surface preparation cost can be decreased. It has excellent welding and cutting properties and presents no health hazard to the welder . CERABOND 2000 has been approved by Lloyd's Register of Shipping as a shop primer which is suitable for welding.
TECHNICAL DATA
Type Fast weldable & heat resistant inorganic zinc silicate shop primer
Recommened
Use
As a shop primer for temporary protection of blast-cleaned steel, as a general purpose rust-preventing primer for organic and inorganic over-coating, and also as a heat resistant paint.
Mixing Ratio : Color :
Paste : Base = 39 : 61 [by volume]Green, Grey, Light grey, Brown, Grey S
Flash Point : Paste = 23.3, Base = 13.0 [degC] Specific Gravity : 1.31 [g/mL] Solid by volume : 36 ±1 [volume %] VOC : 606 [g/L] Coverage(Theoretical): 0.044 [L/m
2
]
Information
Film Thickness : DRY 15 [micron]
(D.F.T. 15micron) 5 oC 10 oC 20 oC 30 oC
Drying Time Surface Dry 3mins. 3mins. 2mins. 2mins.Hard Dry 2hrs. 1.5hrs. 1hr. 1hr.
Painting Interval Min OrganicInorganic
14days16hrs.
10days8hrs.
7days4hrs.
7days4hrs.
Max - - - -Pot Life 36hrs. 30hrs. 24hrs. 15hrs.
Method of Application : Airless spray, Brush Weather : Temperature : 0 - 40
degC, Humidity : 50 - 90 %R.H. For Airless Spray : Viscosity : (Fc#4)9 - 11[sec]
Tip No. : (GRACO)617 - 923 Paint Output Pressuer: 3.8 - 8.9[MPa] Spray Speed : 100 - 160[cm/sec]
Thinner : INORGANIC SHOP PRIMER THINNER, INORGANIC SHOP PRIMER THINNER SThinning: 5 - 25 % by Volume
Preceding Coats :
Conditionof
Application
Subsequent Coats : Most our products or the equivalents. However, when oleoresins paints are applied please consult us.
Packaging Two pack product
Notes 1.Expected life for outdoor exposure (under normal conditions) ; about 6 months
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
2.Oleoresinous coating system over CERABOND 2000 is no recommended on high humid (oftensweaty) or underwater areas.3.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
CERABOND TU(CB TU)
Nov.2006
No. 1034A
CERABOND TU, a two-pack primer, based on a combination of metallic zinc, epoxy resin and hardener. It dries quickly and gives adequate preliminary protection of steel. This primer is completely compatible with almost any type of paint and highly resistant to heat, oil, water and solvent.
TECHNICAL DATA
Type Epoxy zinc rich primer
Recommened
Use
As a primer for protection of blast-cleaned steel plates used for under water area of outer hull
Mixing Ratio : Color :
Base : Hardener = 70 : 30 [by volume]Grey
Flash Point : Base = 10.0, Hardener = 10.0 [degC] Solid by volume : 40 (+-2) [volume %] VOC : 512 [g/L] Coverage(Theoretical): 0.045 [L/m
2
]
Information
Film Thickness : DRY 18 [micron]
(D.F.T. 18micron) 5 oC 10 oC 20 oC 30 oC
Drying Time Surface Dry 8mins. 7mins. 4mins. 3mins.Hard Dry 4hrs. 3hrs. 2hrs. 1.5hrs.
Painting Interval Min 24hrs. 20hrs. 16hrs. 10hrs.Max 180days 180days 180days 150days
Pot Life 72hrs. 60hrs. 48hrs. 24hrs.
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum 5
degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : (Fc#4)9 - 13[sec]
Tip No. : (GRACO)719 Paint Output Pressuer: 8.2 - 11[MPa] Spray Speed : 60 - 160[cm/sec]
Thinner : EPICON MARINE THINNER, Thinning: 10 - 25 % by Volume (for airless spray)
Preceding Coats : -
Conditionof
Application
Subsequent Coats : Most of our products or the equivalents except oleoresins paints.
Packaging Two pack product
Notes VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
CERABOND TU QL(CB TU QL)
Feb.2006
No. 1035B
CERABOND TU QL, a two-pack primer, based on a combination of metallic zinc, epoxy urethane resin and a hardener. It dries quickly and gives adequate preliminary protection of steel after sand- or shot-blasting. This primer is completely compatible with tar-urethane and vinyl-tar anti-corrosive paint and highly resistant to heat, oil, water and solvent.
TECHNICAL DATA
Type Epoxy urethane zinc rich primer
Recommened
Use
As a primer for protection of blast-cleaned steel plates. For the application at low temperature. (-5 - +15ーC)
Mixing Ratio : Color :
Base : Hardener = 78 : 22 [by volume]Grey
Flash Point : Base = 6.0, Hardener = 6.0 [degC] Solid by volume : 44 (+-2) [volume %] VOC : 486 [g/L] Coverage(Theoretical): 0.041 [L/m
2
]
Information
Film Thickness : DRY 18 [micron]
(D.F.T. 18micron) 5 oC 10 oC
Drying Time Surface Dry 4mins. 3mins.Hard Dry 2hrs. 1.5hrs.
Painting Interval Min 16hrs. 12hrs.Max 180days 180days
Pot Life 6hrs. 4hrs.
Method of Application : Airless spray, Brush, Roller Weather : Temperature : -5 - 15
degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : (Fc#4)9 - 13[sec]
Tip No. : (GRACO)719 Paint Output Pressuer: 8.8 - 11.8[MPa] Spray Speed : 60 - 160[cm/sec]
Thinner : EPICON ZINC RICH PRIMER QL THINNER, Thinning: 10 - 25 % by Volume (for airless spray)
Preceding Coats : -
Conditionof
Application
Subsequent Coats : Tar-urethane anti-corrosive paint, Vinyl-tar anti-corrosive paint, Chlorinated rubber anti-corrosive paint, etc.
Packaging Two pack product
Notes VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
CLEANKEEP 201(CK 201)
Nov.2005
No. 6073A
CLEANKEEP 201, based on non-solvent type epoxy resin, is a special coating for drinking water tank interior.It has the following advantages; 1.Non-toxic, non -solvent and odourless 2.Good adhesiveness to various water tank substrates 3.Fast drying 4.Tough, glossy and smooth surfaces 5.Easy application with roller 6.Safe and hygienic since it is non-solvent type 7.Thick film can be formed with one coat. 8.Good anti-corrosive property with the barrier effect because of it's thick solid paint film
TECHNICAL DATA
Type Non-solvent epoxy coating
Recommened
Use
As a interior coating for drinking water tank
Mixing Ratio : Color :
Base : Hardener = 73 : 27 [by volume]Blue
Flash Point : Base = 136, Hardener = 126 [degC] Solid by volume : 100 ±2 [volume %] VOC : 5 [g/L] Coverage(Theoretical): 0.2 [L/m
2
]
Information
Film Thickness : WET 200 [micron]DRY 200 [micron]
(D.F.T. 200micron) 5 oC 10 oC 20 oC 30 oC
Drying Time Surface Dry 16hrs. 8hrs. 3hrs. 2hrs.Hard Dry 24hrs. 16hrs. 8hrs. 5hrs.
Painting Interval Min 24hrs. 16hrs. 8hrs. 5hrs.Max 5days 5days 3days 3days
Pot LifeDry to Launch Min
90mins.48hrs.
60mins.36hrs.
45mins.24hrs.
30mins.24hrs.
Method of Application : Brush, Roller Weather : Temperature : Minimum 5
degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 5.0 - 8.0 Pa・s Thinner : ,
Thinning: - % by Volume Preceding Coats : -
Conditionof
Application
Subsequent Coats : -
Packaging Two pack product
Notes 1."bis-phenol A type" epoxy resin is not used in this paint.2.Please use summer type hardener in summer or high temperature environment.3.Do not use any thinner for application.4.Mixing ratio of Base and Hardener by weight = 4 : 15.Mix materials as required, because of short pot life.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
6.Surface preparation : In case of direct application on steel surface, ISO St3 or more isrequired.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
CLEANKEEP 5000(CK 5000)
Mar.2007
No. 6072
CLEANKEEP 5000, solvent-free epoxy paint, is designed as a protective coating of drinking water tank. CLEANKEEP 5000 is friendly to the environment as it provides no solvent, no heavy metal and less wasted material while coating. CLEANKEEP 5000 could be coated by airless spray.
TECHNICAL DATA
Type Solventfree epoxy coating
Recommened
Use
Fresh water tank, Drinking water tank, Portable water tank
Mixing Ratio : Color :
Base : Hardener = 81 : 19 [by volume]Cream, Light grey
Flash Point : Base = >250, Hardener = 155 [degC] Solid by volume : 100 (+-2) [volume %] VOC : 80 [g/L] Coverage(Theoretical): 0.3 [L/m
2
]
Information
Film Thickness : WET 300 [micron]DRY 300 [micron]
() 10 oC 20 oC 30 oC
Drying Time Surface Dry 45hrs. 18hrs. 11hr.Hard Dry 4days. 32hrs. 24hrs.
Painting Interval Min 4days 32hrs. 24hrs.Max 14days 14days 14days
Pot Life 1.5hrs. 1hr. 45min.
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum 10
degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 3.0 - 4.0Pa・s
Tip No. : (GRACO)619 - 721 Paint Output Pressuer: 23.5 - 33.4[MPa] Spray Speed : 60 - 80[cm/sec]
Thinner : EPICON MARINE THINNER ( for cleaning only ), Thinning: - % by Volume
Preceding Coats : WELBOND, CERABOND, EPICON ZINC RICH PRIMER
Conditionof
Application
Subsequent Coats : -
Packaging Two pack product
Notes 1.Certificated by the test of quality fo Drinking Water as follows:2. - Tests of Effect on Water Quality/BS 6920: 2000- WRAS(UK)3. - SS375: 1994- SINGAPORE4. - Ministry of Health Circular no.102/78: 2001- ITALY5. - Hiroshima City Research Laboratory of Public Health - Japan
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
CLEANKEEP 5000 HOLDING PRIMER(CK 5000 HP)
Jul.2006
No. 6075
CLEANKEEP 5000 HOLDING PRIMER, based on a combination of epoxy resin and hardener, has excellent physical properties such as adhesion, toughness, abrasion resistance, and water resistance. It is particularly compatible with CLEANKEEP 5000 and useful as a holding primer for drinking water tank interiors.
TECHNICAL DATA
Type Epoxy holding primer
Recommened
Use
As holding primer for drinking water tank interiors
Mixing Ratio : Color :
Base : Hardener = 73 : 27 [by volume]Pink
Flash Point : Base = 10.5, Hardener = 10.0 [degC] Specific Gravity : 1.16 [g/mL] Solid by volume : 33 ±2 [volume %] Coverage(Theoretical): 0.152 [L/m
2
]
Information
Film Thickness : WET 152 [micron]DRY 50 [micron]
() 5 oC 10 oC 20 oC 30 oC
Drying Time Surface Dry 3hrs. 90mins. 40mins. 20mins.Hard Dry 18hrs. 8hrs. 4hrs. 2hrs.
Painting Interval Min 18hrs. 8hrs. 4hrs. 2hrs.Max 15days 15days 15days 15days
Pot Life 24hrs. 12hrs. 8hrs. 6hrs.
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum 5
degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 0.9 - 1.0Pa・s
Tip No. : (GRACO)719 Paint Output Pressuer: 8.8 - 11.8[MPa] Spray Speed : 60 - 160[cm/sec]
Thinner : EPICON MARINE THINNER, Thinning: 0 - 5 % by Volume
Preceding Coats : WELBOND, CERABOND, EPICON ZINC RICH PRIMER, NZ PRIMER, etc.
Conditionof
Application
Subsequent Coats : CLEANKEEP 5000
Packaging Two pack product
Notes 1.* In case of outdoor exposure.2.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
CLEANKEEP 5500(CK 5500)
Feb.2006
No. 6072C
CLEANKEEP 5500, solvent-free epoxy paint, is designed as a protective coating of drinking water tank. CLEANKEEP 5500 is friendly to the environment as it provides no solvent, no heavy metal and less wasted material while coating. CLEANKEEP 5500 could be coated by airless spray.
TECHNICAL DATA
Type Solventfree epoxy coating
Recommened
Use
Fresh water tank, Drinking water tank, Portable water tank
Mixing Ratio : Color :
Base : Hardener = 81 : 19 [by volume]Cream, Light grey
Flash Point : Base = >250, Hardener = 155 [degC] Solid by volume : 100 (+-2) [volume %] VOC : 0 [g/L] Coverage(Theoretical): 0.3 [L/m
2
]
Information
Film Thickness : WET 300 [micron]DRY 300 [micron]
() 10 oC 20 oC 30 oC
Drying Time Surface Dry 45hrs. 18hrs. 11hr.Hard Dry 4days. 32hrs. 24hrs.
Painting Interval Min 4days 32hrs. 24hrs.Max 14days 14days 14days
Pot Life 1.5hrs. 1hr. 45min.
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum 10
degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : (Rion viscometer)3 - 4Pa・s
Tip No. : (GRACO)619 - 721 Paint Output Pressuer: 23.5 - 33.4[MPa] Spray Speed : 60 - 80[cm/sec]
Thinner : EPICON MARINE THINNER ( for cleaning only ), Thinning: - % by Volume
Preceding Coats : WELBOND, CERABOND, EPICON ZINC RICH PRIMER
Conditionof
Application
Subsequent Coats : -
Packaging Two pack product
Notes 1.Certificated by the test of quality fo Drinking Water as follows:2.ANSI / NSF - Standard - 61 (USA)3.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
CMP BIOCLEAN HB(CMP BCL HB)
Apr.2007
No. 5982
CMP BIOCLEAN HB is a three-pack silicone elastomer foul release coating.
TECHNICAL DATA
Type Silicone elastomer
Recommened
Use
As a finish coat in the CMP BIOCLEAN foul release system.Especialiy designed for ocean going liners and fast coastal vessels.
Mixing Ratio : Color :
Base:Hardener:Accelerator = 75:20:5 [by volume]Light Grey
Flash Point : Base = 34.5, Hardener = 25.0, Accelerator = 20.5 [degC] Solid by volume : 68 (+-2) [volume %] VOC : 275 [g/L] Coverage(Theoretical): 0.293 [L/m
2
]
Information
Film Thickness : WET 293 [micron]DRY 200 [micron]
(DFT 200microns) 5 oC 10 oC 20 oC 30 oC
Drying Time Surface Dry 7hrs. 5hrs. 3hrs.Hard Dry 24hrs. 18hrs. 12hrs.
Painting Interval Min - - - Max - - -
Pot LifeDry to Launch Min
2hrs.36hrs.
1hr.30hrs.
30mins.24hrs.
Method of Application : Airless spray, Brush Weather : Temperature : 10 - 35
degC, Humidity : 40 - 85 %R.H. For Airless Spray : Viscosity : -
Tip No. : (GRACO)617 - 719 Paint Output Pressuer: Minimum 20.0[MPa] Spray Speed : 60 - 80[cm/sec]
Thinner : RAVAX THINNER, (for cleaning only)Thinning: - % by Volume
Preceding Coats : CMP BIOCLEAN SEALER COAT
Conditionof
Application
Subsequent Coats : -
Packaging Three pack product
Notes
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
CMP BIOCLEAN SEALERCOAT(CMP BCL SC)
Apr.2007
No. 5983
CMP BIOCLEAN SEALER COAT is two pack sealer coat, which enables application of CMP BIOCLEAN system over self-polishing type of anti-fouling paints.
TECHNICAL DATA
Type Modified epoxy paint
Recommened
Use
As a basecoat in the CMP BIOCLEAN foul release system
Mixing Ratio : Color :
Base : Hardener = 78 : 22 [by volume]Grey
Flash Point : Base = 23.1, Hardener = 24.9 [degC] Solid by volume : 55 (+-2) [volume %] VOC : 382 [g/L] Coverage(Theoretical): 0.154 [L/m
2
]
Information
Film Thickness : WET 154 [micron]DRY 100 [micron]
(DFT 100microns) 5 oC 10 oC 20 oC 30 oC
Drying Time Surface Dry 7hrs. 5.5hrs. 4hrs. 2.5hrs.Hard Dry 24hrs. 18hrs. 10hrs. 8hrs.
Painting Interval Min 7hrs. 6hrs. 4hrs. 3hrs.Max * - - - -
Pot Life 18hrs. 14hrs. 7hrs. 4hrs.
Method of Application : Airless spray, Brush Weather : Temperature : Minimum 5
degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 1.6 - 2 Pa・s
Tip No. : (GRACO)621,623 Paint Output Pressuer: 14.7 - 17.7[MPa] Spray Speed : 60 - 80[cm/sec]
Thinner : EPICON THINNER, Thinning: 0 - 5 % by Volume
Preceding Coats : SEA GRANDPRIX 500,1000,CF-10, BANNOH 500 etc.
Conditionof
Application
Subsequent Coats : CMP BIOCLEAN SYSTEM
Packaging Two pack product
Notes 1.*Please refer to painting specification.2.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
EPICON MARINE CH(EPM CH)
Feb.2006
No. 5409
EPICON MARINE CH, based on a combination of epoxy resin and polyamide curing agent, has high-build excellent durability and adhesion properties. It is suitable for carhold.
TECHNICAL DATA
Type Epoxy paint
Recommened
Use
Carhold, inside of steel superstructures, anticorosive finish coat
Mixing Ratio : Color :
Base : Hardener = 78 : 22 [by volume]White (Standard)
Flash Point : Base = 24.0, Hardener = 16.0 [degC] Solid by volume : 58 (+-2) [volume %] VOC : 466 [g/L] Coverage(Theoretical): 0.085 - 0.172 [L/m
2
]
Information
Film Thickness : WET 86 - 172 [micron]DRY 50 - 100 [micron]
(D.F.T. 100micron) 5 oC 10 oC 20 oC 30 oC
Drying Time Surface Dry 4.5hrs. 3.5hrs. 2hrs. 1hr.Hard Dry 45hrs. 30hrs. 16hrs. 12hrs.
Painting Interval Min 28hrs. 19hrs. 10hrs. 8hrs.Max * - - - -
Pot Life 24hrs. 12hrs. 12hrs. 8hrs.
Method of Application : Airless spray, Brush Weather : Temperature : Minimum 5
degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 1.5Pa・s
Tip No. : (GRACO)719,721 Paint Output Pressuer: 14.7 - 17.7[MPa] Spray Speed : 60 - 80[cm/sec]
Thinner : EPICON MARINE THINNER, Thinning: 0 - 5 % by Volume
Preceding Coats : BANNOH 500, BANNOH 200, etc.
Conditionof
Application
Subsequent Coats : -
Packaging Two pack product
Notes 1.* Please refer to the painting specifications.2.As nature of epoxy coatings EPICON MARINE CH can not avoid chalking and fading on UV exposure.3.Please consult our representative about color variation4.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
EPICON MARINE HB(EPM HB)
Feb.2006
No. 5402
EPICON MARINE HB, based on a combination of epoxy resin and polyamide curing agent, has high-build excellent durability and adhesion properties. It is suitable as a finish coat for protection of steel ships, bridges and steel structures.
TECHNICAL DATA
Type Epoxy/Polyamide finish coat, high-build
Recommened
Use
Finish coat of EPICON MARINE system of steel ships, bridges and other steel structures
Mixing Ratio : Color :
Base : Hardener = 73 : 27 [by volume]As specified(except White)
Flash Point : Base = 23.0, Hardener = 27.5 [degC] Solid by volume : 58 (+-2) [volume %] VOC : 465 [g/L] Coverage(Theoretical): 0.052 - 0.172 [L/m
2
]
Information
Film Thickness : WET 52 - 172 [micron]DRY 30 - 100 [micron]
(D.F.T. 100micron) -5 oC 0 oC 5 oC 10 oC 20 oC 30 oC
Drying Time Surface Dry 5.5hrs. 4.5 3.5hrs. 2.5hrs. 1.5hrs. 1hr.Hard Dry 55hrs. 55hrs. 38hrs. 28hrs. 16hrs. 12hrs.
Painting Interval Min 55hrs. 44hrs. 24hrs. 18hrs. 10hrs. 8hrs.Max * - - - - - -
Pot Life 24hrs. 24hrs. 24hrs. 12hrs. 12hrs. 8hrs.
Method of Application : Airless spray Weather : Temperature : Minimum -5
degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 1.5Pa・s
Tip No. : (GRACO)719,721 Paint Output Pressuer: 14.7 - 17.7[MPa] Spray Speed : 60 - 80[cm/sec]
Thinner : EPICON MARINE THINNER, Thinning: 0 - 5 % by Volume
Preceding Coats : BANNOH 500, BANNOH 200, etc.
Conditionof
Application
Subsequent Coats : -
Packaging Two pack product
Notes 1.* Please refer to the painting specifications.2.As nature of epoxy coatings EPICON MARINE HB can not avoid chalking and fading on UV exposure.3.Application at temperatures down to -5 degC is possible but curing to hardness takes longer and complete cure will be reached when temperature increases.4.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
EPICON MARINE UNDERCOAT M(EPM UC M)
Feb.2006
No. 5301
EPICON MARINE UNDERCOAT M, based on a combination of modified epoxy resin and Polyamide curing agent, has excellent durability and adhesion properties. It is protective undercoat for steel ships, bridges and steel structures.
TECHNICAL DATA
Type Modified epoxy/Polyamide undercoat
Recommened
Use
Undercoat of steel ships, bridges and other steel structures
Mixing Ratio : Color :
Base : Hardener = 80 : 20 [by volume]Black, White
Flash Point : Base = 24.5, Hardener = 27.5 [degC] Solid by volume : 45 (+-2) [volume %] VOC : 505 [g/L] Coverage(Theoretical): 0.088 - 0.131 [L/m
2
]
Information
Film Thickness : WET 88 - 131 [micron]DRY 40 - 60 [micron]
() 5 oC 10 oC 20 oC 30 oC
Drying Time Surface Dry 3.5hrs. 2.5hrs. 1.5hrs. 1hr.Hard Dry 34hrs. 24hrs. 14hrs. 10hrs.
Painting Interval Min 24hrs. 24hrs. 16hrs. 8hrs.Max * - - - -
Pot Life 24hrs. 24hrs. 18hrs. 12hrs.
Method of Application : Airless spray, Brush Weather : Temperature : Minimum 5
degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : (Fc#4)80[sec]
Tip No. : (GRACO)619,719 Paint Output Pressuer: 14.7 - 17.7[MPa] Spray Speed : 60 - 80[cm/sec]
Thinner : EPICON MARINE THINNER, Thinning: 0 - 5 % by Volume
Preceding Coats : EPICON MARINE HB-AL, EPICON MARINE HB-CL, BANNOH 200, BANNOH 500 AC, etc.
Conditionof
Application
Subsequent Coats : RAVAX FINISH, UNY MARINE, etc.
Packaging Two pack product
Notes 1.Please refer to the painting specifications.2.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
EPICON T-500(EP T-500)
Feb.2006
No. 6025
EPICON T-500, a high build type epoxy coating, has excellent physical properties such as adhesion, toughness, abrasion resistance, etc. as well as chemical resistance to fresh water, petroleum products, crude oil, alkalis and weak acids. It is suitable as a protective coating for tank interiors. Airless spray can build a dry film thickness of 75-125 microns per coat.
TECHNICAL DATA
Type Epoxy tank coating, high-build
Recommened
Use
Product carrier tank, Cargo oil tank, Fresh water tank, Drinking water tank, Portable water tank, Hold, Solvent tank, Chemical tank, etc.
Mixing Ratio : Color :
Base : Hardener = 79 : 21 [by volume]Red brown, Grey, Light Grey, White
Flash Point : Base = 13.0, Hardener = 15.5 [degC] Solid by volume : 58 (+-2) [volume %] VOC : 423 [g/L] Coverage(Theoretical): 0.13 - 0.216 [L/m
2
]
Information
Film Thickness : WET 130 - 216 [micron]DRY 75 - 125 [micron]
(D.F.T. 125micron) 5 oC 10 oC 20 oC 30 oC
Drying Time Surface Dry 3.5hrs. 2.5hrs. 1.5hrs. 30mins.Hard Dry 36hrs. 24hrs. 12hrs. 6hrs.
Painting Interval Min 36hrs. 24hrs. 12(16)hrs. 6(14)hrs.Max
*10days
5days10days
4days7days3days
5days2days
Pot Life 10hrs. 7hrs. 5hrs. 3hrs.
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum 5(10)
degC, Humidity : Dew Point +Minimum 5 degC
For Airless Spray : Viscosity : 1 - 1.5 Pa・s Tip No. : (GRACO)619,621 Paint Output Pressuer: 14.7 - 17.7[MPa] Spray Speed : 60 - 80[cm/sec]
Thinner : EPICON T-500 THINNER , EPICON T-500 S THINNER, EPICON T-500 THINNER for WINTERThinning: 0 - 10 % by Volume
Preceding Coats : WELBOND, CERABOND, EPICON ZINC RICH PRIMER, NZ PRIMER, EPICON T-500 PRIMER H,
Conditionof
Application
Subsequent Coats : EPICON T-500
Packaging Two pack product
Notes 1.Shown above "( )" are for tank coating of product carrier, please refer to Chugoku's catalogue "Product Carrier Tank Coating" in detail.2.* Maximum painting interval is 3 days at 20degC when it is exposed outdoors.3.** On steel : Dew point+Min. 5 degC On paint film : Dew point+Min. 3 degC
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
4.Waiting time before the first cargo loading Temp. 10degC 20degC 30degC (Days) 18 10 6
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
EPICON T-500 FOR REPAIR()
Feb.2006
No. 6025R
EPICON T-500 FOR REPAIR, high build type epoxy coating, has excellent physsical properites such as adhesion, toughness, abrasion resistance, etc., and chemical resistance to salt water, petroleum products, crude oil, alkaris and weak acid, and is suitable as a protective coating of tank interior. A dry fil thickness of 8 - 10 mils can be built in brush application. It is suitable as a protective coating tank interior.
TECHNICAL DATA
Type Epoxy tank coating, high-build
Recommened
Use
Cargo oil tank, fresh water tank, hold, solvent tank, chemical tank, etc.
Mixing Ratio : Color :
Base : Hardener = 77 : 23 [by volume]Red brown, Grey, Light Grey
Flash Point : Base = 13.0, Hardener = 24.0 [degC] Solid by volume : 59(+-2) [volume %] VOC : 342 [g/L] Coverage(Theoretical): 0.128 - 0.213 [L/m
2
]
Information
Film Thickness : WET 128 - 213 [micron]DRY 75 - 125 [micron]
() 5 oC 10 oC 20 oC 30 oC
Drying Time Surface Dry 3.5hrs. 2.5hrs. 1.5hrs. 30hrs.Hard Dry 36hrs. 24hrs. 12hrs. 6hrs.
Painting Interval Min 36hrs. 24hrs. 12hrs. 6hrs.Max
*10days
(5)10days
(4)7days
(3)5days
(2)Pot Life 10hrs. 7hrs. 5hrs. 3hrs.
Method of Application : Brush, Roller Weather : Temperature : Minimum 5
degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 7.5Pa・s Thinner : EPICON T-500 THINNER,
Thinning: 0 % by Volume Preceding Coats : EPICON T-500, BONDET PUTTY
Conditionof
Application
Subsequent Coats : -
Packaging Two pack product
Notes 1.Maximum painting interval at 20 degree C is 3 days when it is exposed outdoors.2.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
EPICON T-500 HS(EP T-500 HS)
Sep.2006
No. 6032
EPICON T-500 HS, a high build type epoxy coating, has excellent physical properties such as adhesion, toughness, abrasion resistance, etc. as well as chemical resistance to salt-water, fresh water, petroleum products, crude oil, alkalis and weak acids. It is suitable as a protective coating for tank interiors. Airless spray can build a dry film thickness of 100-125 microns per coat.
TECHNICAL DATA
Type Epoxy tank coating, high-build
Recommened
Use
Cargo oil tank, solvent tank, chemical tank, etc.
Mixing Ratio : Color :
Base : Hardener = 77 : 23 [by volume]Red brown, Grey, Light Grey
Flash Point : Base = 17.5, Hardener = 46.5 [degC] Solid by volume : 74 (+-2) [volume %] VOC : 267 [g/L] Coverage(Theoretical): 0.135 - 0.203 [L/m
2
]
Information
Film Thickness : WET 135 - 203 [micron]DRY 100 - 150 [micron]
() 10 oC 20 oC 30 oC
Drying Time Surface Dry 2.5hrs. 1.5hrs. 30mins.Hard Dry 24hrs. 12hrs. 6hrs.
Painting Interval Min 24hrs. 16hrs. 14hrs.Max 10days 7days 5days
Pot Life 7hrs. 5hrs. 3hrs.
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum 10
degC, Humidity : Dew Point +Minimum 5 degC
For Airless Spray : Viscosity : 1.3 - 1.8 Pa・s Tip No. : (GRACO)619,621 Paint Output Pressuer: 14.7 - 17.7[MPa] Spray Speed : 60 - 80[cm/sec]
Thinner : EPICON T-500 THINNER , EPICON T-500 S THINNER, EPICON T-500 THINNER for WINTERThinning: 0 - 10 % by Volume
Preceding Coats : WELBOND, CERABOND, EPICON ZINC RICH PRIMER, NZ PRIMER, etc.
Conditionof
Application
Subsequent Coats : EPICON T-500 HS
Packaging Two pack product
Notes 1. On steel : Dew point+Min. 5 degC On paint film : Dew point+Min. 3 degC2.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
EPICON T-500 PRIMER H(EP T-500 H)
Apr.2006
No. 6020A
EPICON T-500 PRIMER H, based on a combination of epoxy resin and hardener, has excellent physical properties such as adhesion, toughness, abrasion resistance, etc. and chemical resistance to salt-water, petroleum products, crude oil, alkalis and weak acids, and it is particularly compatible with EPICON T-500. When this product is used as a folding primer, please reference the Notes.
TECHNICAL DATA
Type Epoxy tank coating
Recommened
Use
As primer for product carrier tank interiors and useful as holding primer
Mixing Ratio : Color :
Base : Hardener = 73 : 27 [by volume]Pink brown
Flash Point : Base = 13.0, Hardener = 15.5 [degC] Solid by volume : 33 (+-2) [volume %] VOC : 595 [g/L] Coverage(Theoretical): 0.152 [L/m
2
]
Information
Film Thickness : WET 152 [micron]DRY 50 [micron]
(D.F.T. 50micron) 10 oC 20 oC 30 oC
Drying Time Surface Dry 90mins. 40mins. 20mins.Hard Dry 16hrs. 8hrs. 4hrs.
Painting Interval Min 16hrs. 12hrs. 8hrs.Max
*15days(7)days
15days(5)days
15days(3)days
Pot Life 24hrs. 16hrs. 12hrs.
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum 10
degC, Humidity : Dew Point +Minimum 5 degC
For Airless Spray : Viscosity : 0.9 - 1Pa・s Tip No. : (GRACO)719 Paint Output Pressuer: 8.8 - 11.8[MPa] Spray Speed : 60 - 160[cm/sec]
Thinner : EPICON T-500 THINNER, EPICON T-500 S THINNER, EPICON T-500 THINNER for WINTERThinning: 0 - 5 % by Volume
Preceding Coats : WELBOND, NZ PRIMER, EPICON ZINC RICH PRIMER, etc.
Conditionof
Application
Subsequent Coats : EPICON T-500
Packaging Two pack product
Notes 1.* In case of outdoor exposure.2.In case of using as holding primer, please reference the following. Coverage 0.076L/m2 Film thickness WET:76micron, DRY:25micron (D.F.T 25micron) 10decC 20degC 30degC Drying time Surface Dry 15mins. 10mins. 6mins.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
Hard Dry 3hrs. 2hrs. 1.5hrs. Painting Interval Min 16hrs. 12hrs. 8hrs. Max 15days 15days 15days Max * 7days 5days 3days Pot Life 16hrs. 10hrs. 6hrs. Viscosity Ford cup No.4 : 16 sec Thinning for airless spray : 0 - 10 % by Volume3.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
EPICON T-800(EP T-800)
Feb.2006
No. 6037
EPICON T-800, a high-build type epoxy phenolic coating, has excellent physical properties such as adhesion, toughness, abrasion resistance, etc. as well as chemical resistance to salt-water, fresh water, petroleum products, crude oil, alkalis and weak acids. It is suitable as a protective coating for tank interiors. Airless spray can build a dry film thickness of 75-125 microns per coat.
TECHNICAL DATA
Type Epoxy phenolic tank coating, high-build
Recommened
Use
Product carrier tank, Chemical tank, etc.
Mixing Ratio : Color :
Base : Hardener = 84 : 16 [by volume]Grey, Light Grey, Red brown
Flash Point : Base = 17.5, Hardener = 7.5 [degC] Solid by volume : 63 (+-2) [volume %] VOC : 332 [g/L] Coverage(Theoretical): 0.119 - 0.199 [L/m
2
]
Information
Film Thickness : WET 119 - 199 [micron]DRY 75 - 125 [micron]
() 10 oC 20 oC 30 oC
Drying Time Surface Dry 2.5hrs. 1.5hrs. 30mins.Hard Dry 24hrs. 12hrs. 6hrs.
Painting Interval Min 24hrs. 16hrs. 14hrs.Max
*10days(4)days
7days(3)days
5days(2)days
Pot Life 7hrs. 5hrs. 3hrs.
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum 10
degC, Humidity : Dew Point +Minimum 5 degC
For Airless Spray : Viscosity : 1.0 - 1.5Pa・s Tip No. : (GRACO)619,621 Paint Output Pressuer: 14.7 - 17.7[MPa] Spray Speed : 60 - 80[cm/sec]
Thinner : EPICON T-800 THINNER, Thinning: 0 - 10 % by Volume
Preceding Coats : EPICON T-800 HOLDING PRIMER , EPICON T-800, CERABOND, WELBOND, EPICON ZINC RICH PRIMER
Conditionof
Application
Subsequent Coats : EPICON T-800
Packaging Two pack product
Notes 1.* In case of outdoor exposure.2. On steel : Dew point+Min. 5 degC On paint film : Dew point+Min. 3 degC
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
EPICON T-800 HOLDING PRIMER(EP T-800 HP)
Apr.2006
No. 6035
EPICON T-800 HOLDING PRIMER, based on a combination of epoxy phenolic resin, rust-preventive pigments and hardener, has chemical resistance to salt-water, petroleum products, crude oil, alkalis and weak acids. It is particularly compatible with EPICON T-800 and useful as a holding primer for product carrier tank interiors.
TECHNICAL DATA
Type Epoxy phenolic holding primer
Recommened
Use
As a holding primer for product carrier tank interiors
Mixing Ratio : Color :
Base : Hardener = 85 : 15 [by volume]Pink brown
Flash Point : Base = 17.5, Hardener = 8.0 [degC] Solid by volume : 35 (+-2) [volume %] VOC : 577 [g/L] Coverage(Theoretical): 0.072 [L/m
2
]
Information
Film Thickness : WET 72 [micron]DRY 25 [micron]
() 10 oC 20 oC 30 oC
Drying Time Surface Dry 15mins. 10mins. 6mins.Hard Dry 3hrs. 2hrs. 1.5hrs.
Painting Interval Min 16hrs. 8hrs. 5hrs.Max
*15days(7)days
15days(5)days
15days(3)days
Pot Life 24hrs. 16hrs. 12hrs.
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum 10
degC, Humidity : Dew Point +Minimum 5 degC
For Airless Spray : Viscosity : (Fc#4)9 - 10[sec] Tip No. : (GRACO)719 Paint Output Pressuer: 8.8 - 11.8[MPa] Spray Speed : 60 - 160[cm/sec]
Thinner : EPICON T-800 THINNER, Thinning: 0 - 20 % by Volume
Preceding Coats : CERABOND, WELBOND
Conditionof
Application
Subsequent Coats : EPICON T-800
Packaging Two pack product
Notes 1.* In case of outdoor exposure.2.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
EPICON T-800 HS(EP T-800 HS)
Oct.2006
No. 6033
EPICON T-800 HS, a high-solid type epoxy phenolic coating, has excellent physical properties such as adhesion, toughness, abrasion resistance, etc. as well as chemical resistance to salt-water, fresh water, petroleum products, crude oil, alkalis and weak acids. It is suitable as a protective coating for tank interiors. Airless spray can build a dry film thickness of 100-150 microns per coat.
TECHNICAL DATA
Type Epoxy phenolic tank coating, high-solid
Recommened
Use
Product carrier tank, Chemical tank, etc.
Mixing Ratio : Color :
Base : Hardener = 83 : 17 [by volume]Red brown, Light Grey, Grey
Flash Point : Base = 24.0, Hardener = 10.0 [degC] Solid by volume : 77 ±2 [volume %] VOC : 264 [g/L] Coverage(Theoretical): 0.13 - 0.195 [L/m
2
]
Information
Film Thickness : WET 130 - 195 [micron]DRY 100 - 150 [micron]
() 10 oC 20 oC 30 oC
Drying Time Surface Dry 2.5hrs. 1.5hrs. 30mins.Hard Dry 24hrs. 12hrs. 6hrs.
Painting Interval Min 24hrs. 16hrs. 14hrs.Max 10days 7days 5days
Pot Life 6hrs. 4hrs. 2.5hrs.
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum 10
degC, Humidity : Dew Point +Minimum 5 degC
For Airless Spray : Viscosity : 1.3 - 1.7Pa・s Tip No. : (GRACO)619,621 Paint Output Pressuer: 14.7 - 17.7[MPa] Spray Speed : 60~80[cm/sec]
Thinner : EPICON T-800 THINNER, Thinning: 0 - 10 % by Volume
Preceding Coats : CERABOND, EPICON ZINC RICH PRIMER
Conditionof
Application
Subsequent Coats : EPICON T-800 HS
Packaging Two pack product
Notes 1.Application of block is not recommended. If defumidification and temperature can not be controlled, application should not be carried out.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
EPICON ZINC RICH PRIMER B-2(EPZR B-2)
Nov.2006
No. 1034
EPICON ZINC RICH PRIMER B-2, a two-pack primer, based on a combination of metallic zinc, epoxy resin and hardener. It dries quickly and gives adequate preliminary protection of steel after sand- or shot-blasting. This primer is completely compatible with almost all type of coatings and highly resistant to heat, oil, water and solvent.
TECHNICAL DATA
Type Epoxy zinc rich primer
Recommened
Use
As a primer for protection of blast-cleaned steel plates used for under water area of outer hull
Mixing Ratio : Color :
Base : Hardener = 70 : 30 [by volume]Grey
Flash Point : Base = 10.0, Hardener = 10.0 [degC] Solid by volume : 40 (+-2) [volume %] VOC : 512 [g/L] Coverage(Theoretical): 0.045 [L/m
2
]
Information
Film Thickness : DRY 18 [micron]
(D.F.T. 18micron) 5 oC 10 oC 20 oC 30 oC
Drying Time Surface Dry 8mins. 7mins. 4mins. 3mins.Hard Dry 4hrs. 3hrs. 2hrs. 1.5hrs.
Painting Interval Min 24hrs. 20hrs. 16hrs. 10hrs.Max 180days 180days 180days 150days
Pot Life 72hrs. 60hrs. 48hrs. 24hrs.
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum 5
degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : (Fc#4)9 - 13[sec]
Tip No. : (GRACO)719 Paint Output Pressuer: 8.2 - 11.0[MPa] Spray Speed : 60 - 160[cm/sec]
Thinner : EPICON MARINE THINNER, Thinning: 10 - 25 % by Volume (for airless spray
Preceding Coats : -
Conditionof
Application
Subsequent Coats : Most of our products or the equivalents except oleoresins paints.
Packaging Two pack product
Notes 1. * Minimum painting interval for touch up is 4 hours at 20degC 2.This primer has good workability and good adhesion with almost all type of over coatings. Therefore, this primer is suitable for touch-up coating.3.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
EPICON ZINC RICH PRIMER B-2 QL(EPZR B-2 QL)
Feb.2006
No. 1035A
EPICON ZINC RICH PRIMER B-2 QL, a two-pack primer, based on a combination of metallic zinc, epoxy urethane resin and a hardener. It dries quickly and gives adequate preliminary protection of steel after sand- or shot-blasting. This primer is completely compatible with tar-urethane and vinyl-tar anti-corrosive paint and highly resistant to heat, oil, water and solvent.
TECHNICAL DATA
Type Epoxy urethane zinc rich primer
Recommened
Use
As a primer for protection of blast-cleaned steel plates. For the application at low temperature. (-5 - +15C)
Mixing Ratio : Color :
Base : Hardener = 78 : 22 [by volume]Grey
Flash Point : Base = 6.0, Hardener = 6.0 [degC] Solid by volume : 44 (+-2) [volume %] VOC : 486 [g/L] Coverage(Theoretical): 0.041 [L/m
2
]
Information
Film Thickness : DRY 18 [micron]
(D.F.T. 18micron) -5 oC 0 oC 5 oC 10 oC
Drying Time Surface Dry 8mins. 6mins. 4mins. 3mins.Hard Dry 4hrs. 3hrs. 2hrs. 1.5hrs.
Painting Interval Min 36hrs. 24hrs. 16 12Max 180days 180days 180days 180days
Pot Life 10hrs. 8hrs. 6hrs. 4hrs.
Method of Application : Airless spray, Brush, Roller Weather : Temperature : -5 - 15
degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : (Fc#4)9 - 13[sec]
Tip No. : (GRACO)719 Paint Output Pressuer: 8.8 - 11.8[MPa] Spray Speed : 60 - 160[cm/sec]
Thinner : EPICON ZINC RICH PRIMER QL THINNER, Thinning: 10 - 25 % by Volume
Preceding Coats : -
Conditionof
Application
Subsequent Coats : Tar-urethane anti-corrosive paint, Vinyl-tar anti-corrosive paint, Chlorinated rubber anti-corrosive paint, etc.
Packaging Two pack product
Notes 1.The temperature of the mixed base and hardener preferably should be above 0 degC otherwise extra solvent may be required to obtain appliaction viscosity.2.Too much solvent results in reduced sag resistance.3.Application at temperatures down to -5 degC is possible but curing to hardness takes longer and complete cure will be reached when temperature increases.4.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
ETCHING PRIMER H(ETP H)
Oct.2006
No. 1061
ETCHING PRIMER H is a two-component etching primer, based on butyral resin, chemically drying by reaction of the mixed components and providing a temporary protection against corrosion and increasing the adhesive property of the subsequent coats.
TECHNICAL DATA
Type Butyral resin based etching primer
Recommened
Use
As a pre-treatment primer on non-ferrous metals such as aluminium and light alloys as well as zinc and galvanized iron. May also be used as a pre-treatment primer on blast-cleaned steel plates
Mixing Ratio : Color :
Base : Additive = 80 : 20 [by volume]Yellow
Flash Point : Base = 17.5, Additive = 15.0 [degC] Solid by volume : 10 [volume %] VOC : 703 [g/L] Coverage(Theoretical): 0.08 [L/m
2
]
Information
Film Thickness : DRY 8 [micron]
(D.F.T. 8micron) 5 oC 10 oC 20 oC 30 oC
Drying Time Surface Dry 20mins. 15mins. 10mins. 7mins.Hard Dry 2hrs. 1.5hrs. 1hr. 30min.
Painting Interval Min 6hrs. 4hrs. 3hrs. 2hrs.Max 24hrs. 24hrs. 24hrs. 24hrs.
Pot Life 24hrs. 16hrs. 8hrs. 6hrs.
Method of Application : Airless spray, Brush Weather : Temperature : Minimum 5
degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : (IWATA CUP)18 - 22[sec]
Tip No. : (GRACO)617 Paint Output Pressuer: 8.8 - 11.8[MPa] Spray Speed : 90 - 120[cm/sec]
Thinner : ETCHING PRIMER THINNER, Thinning: 35 - 50 % by Volume (for airless spray)
Preceding Coats : -
Conditionof
Application
Subsequent Coats : Any one of our products and/or the equivalent ,e.g.:, Oleoresinous paint, Chlorinated rubber paint, Vinyl paint, Epoxy paint, Tar-epoxy paint
Packaging Two pack product
Notes VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
ETCHING PRIMER H(for Peller Clean Set Jr)()
Feb.2006
No. 1061Q
ETCHING PRIMER H(for Peller Clean Set Jr) is a three-component etching primer, based on butyral resin, chemically drying by reaction of the mixed components and providing a excellent adhesive property for propeller surfece and the subsequent coat .(Bioclean DX)
TECHNICAL DATA
Type Butyral resin based etching primer
Recommened
Use
As a primer of Bioclean DX for propeller
Mixing Ratio : Color :
Base:Additive:Adhisive agent = 4 : 1 : 1 [by volume]Yellow
Flash Point : Base = 17.5, Additive = 15.0, Adhisive agent = 26.0 [degC] Solid by volume : 10 [volume %] VOC : 726 [g/L] Coverage(Theoretical): 0.08 [L/m
2
]
Information
Film Thickness : WET 86 [micron]DRY 8 [micron]
() 5 oC 10 oC 20 oC 30 oC
Drying Time Surface Dry 20mins. 15mins. 10mins. 7mins.Hard Dry 2hrs. 1.5hrs. 1hr. 30mins.
Painting Interval Min 6hrs. 4hrs. 3hrs. 2minMax 24 24 24 24
Pot Life 24hrs. 16hrs. 8hrs. 6hrs.
Method of Application : Airless spray; Brush Weather : Temperature : Minimum 5
degC, Humidity : Maximum 85 %R.H. Thinner : ETCHING PRIMER THINNER,
Thinning: 35 - 50 % by Volume Preceding Coats : -
Conditionof
Application
Subsequent Coats : Any one of our products and/or the equivalent ,e.g.:, Oleoresinous paint, Chlorinated rubber paint, Vinyl paint, Epoxy paint, Tar-epoxy paint
Packaging Three pack product
Notes VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
ETCHING PRIMER H(for Peller Clean Set)()
Feb.2006
No. 1061P
ETCHING PRIMER H(for Peller Clean Set) is a three-component etching primer, based on butyral resin, chemically drying by reaction of the mixed components and providing a excellent adhesive property for propeller surfece and the subsequent coat.(Bioclean DX)
TECHNICAL DATA
Type Butyral resin based etching primer
Recommened
Use
As a primer of Bioclean DX for propeller
Mixing Ratio : Color :
Base : Additive : Adhisive agent = 4 : 1 : 0.25 [by volume]Yellow
Flash Point : Base = 17.5, Additive = 15.0, Adhisive agent = 26.0 [degC] Solid by volume : 10 (+-2) [volume %] VOC : 706 [g/L] Coverage(Theoretical): 0.08 [L/m
2
]
Information
Film Thickness : WET 72 [micron]DRY 8 [micron]
() 5 oC 10 oC 20 oC 30 oC
Drying Time Surface Dry 20mins. 15mins. 10mins. 7mins.Hard Dry 2hrs. 1.5hrs. 1hr. 30mins.
Painting Interval Min 6hrs. 4hrs. 3hrs. 2hrs.Max 24hrs. 24hrs. 24hrs. 24hrs.
Pot Life 24hrs. 16hrs. 8hrs. 6hrs.
Method of Application : Airless spray, Brush Weather : Temperature : Minimum 5
degC, Humidity : Maximum 85 %R.H. Thinner : ETCHING PRIMER THINNER,
Thinning: 35 - 50 % by Volume Preceding Coats : -
Conditionof
Application
Subsequent Coats : Any one of our products and/or the equivalent ,e.g.:, Oleoresinous paint, Chlorinated rubber paint, Vinyl paint, Epoxy paint, Tar-epoxy paint
Packaging Three pack product
Notes VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
EVAMARINE(EM)
Feb.2006
No. 2400A
EVAMARINE is an alkyd resin based paint with excellent adhesion property, weathering resistance and excellent colour retention.
TECHNICAL DATA
Type Alkyd resin finish paint
Recommened
Use
As a finishing coat on exterior wood and steel surfaces
Color : As specified, Flash Point : 43.0 [degC] Solid by volume : 49 (+-2) [volume %] VOC : 385 [g/L] Coverage(Theoretical): 0.051 - 0.071 [L/m
2
]
Information
Film Thickness : WET 51 - 71 [micron]DRY 25 - 35 [micron]
() 0 oC 5 oC 10 oC 20 oC 30 oC
Drying Time Surface Dry 5hrs. 4hrs. 3hrs. 2hrs. 1.5hrs.Hard Dry 48hrs. 30hrs. 16hrs. 8hrs. 6hrs.
Painting Interval Min 72hrs. 48hrs. 24hrs. 16hrs. 12hrs.Max - - - - -
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum 0
degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : (Fc#4)110[sec]
Tip No. : (GRACO)615,715 Paint Output Pressuer: 10.7 - 13.8[MPa] Spray Speed : 80 - 100[cm/sec]
Thinner : MARINE THINNER, Thinning: 0 - 5 % by Volume
Preceding Coats : LZI PRIMER, RED LEAD PRIMER QD, EVAMARINE UNDERCOAT, etc.
Conditionof
Application
Subsequent Coats : -
Packaging One pack product
Notes Applying within the recommended film thickness range to avoid the wrinkling.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
EVAMAX 100P(EX 100P)
Feb.2006
No. 6435
EVAMAX 100P is based on a combination of epoxy resin, special abrasive resistant agent and polyamide resin. It provides excellent characteristics in adhesion, toughness, impact, abrasion resistance and rust-prevention. It is suitable for protection of exposed deck and holds of steel ships.
TECHNICAL DATA
Type Epoxy/Polyamide, high-build
Recommened
Use
Ship's deck and hold
Mixing Ratio : Color :
Base : Hardener = 75 : 25 [by volume]Grey, Red brown
Flash Point : Base = 21.2, Hardener = 30.5 [degC] Solid by volume : 58 ±2 [volume %] VOC : 409 [g/L] Coverage(Theoretical): 0.216 - 0.432 [L/m
2
]
Information
Film Thickness : WET 216 - 432 [micron]DRY 125 - 250 [micron]
(D.F.T. 200micron) 5 oC 10 oC 20 oC 30 oC
Drying Time Surface Dry 4.5hrs. 3.5hrs. 2.5hrs. 1.5hrs.Hard Dry 44hrs. 27hrs. 17hrs. 12hrs.
Painting Interval Min 44hrs. 27hrs. 17hrs. 12hrs.Max 90days 90days 90days 90days
Pot Life 24hrs. 14hrs. 8hrs. 5hrs.
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum 5
degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 1.5 - 2Pa・s
Tip No. : (GRACO)623 Paint Output Pressuer: 14.7 - 17.7[MPa]
Spray Speed : 60 - 80[cm/sec] Thinner : EVAMAX THINNER,
Thinning: 0 - 5 % by Volume Preceding Coats : WELBOND, CERABOND, EPICON ZINC RICH PRIMER, NZ PRIMER
Conditionof
Application
Subsequent Coats : EPICON MARINE FINISH
Packaging Two pack product
Notes 1. In confined spaces such as tank insides ventilation is required during application and curing to remove solvent vapours and promote curing.2.Waiting time before the first cargo loading Temp. 10degC 20degC 30degC (Days) 18 10 6
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
GALBON SP(GB SP)
Feb.2006
No. 6240
GALBON SP is a combination of selected zinc dust and ethyl silicate solution producing an inorganic coat which gives outstanding prolonged weather resistance, effective and long-term protection against corrosion, solvent and oil resistance, heat resistance ( up to 400 decC), and resistance to fresh and salt water.
TECHNICAL DATA
Type Inorganic zinc silicate alcohol soluble and self-curing
Recommened
Use
As a shop primer, as a protective coating for oil tanks, solvent tanks, ballast tanks, heating pipes, holds, etc.
Mixing Ratio : Color :
Base : Powder = 76 : 24 [by volume]Grey
Flash Point : Base = 14.5, Powder = - [degC] Solid by volume : 39 [volume %] VOC : 464 [g/L] Coverage(Theoretical): 0.051 [L/m
2
]
Information
Film Thickness : WET 51 [micron]DRY 18 [micron]
() 5 oC 10 oC 20 oC 30 oC
Drying Time Surface Dry 10mins. 8mins. 5mins. 3mins.Hard Dry 2hrs. 1.5hrs. 1hr. 40mins.
Painting Interval Min 24hrs. 20hrs. 16hrs. 10hrs.Max 180days 180days 180days 180days
Pot Life 16hrs. 12hrs. 8hrs. 5hrs.
Method of Application : Airless spray, Air spray, Brush Weather : Temperature : 0 - 50
degC, Humidity : 50 - 95 %R.H. For Airless Spray : Viscosity : (Fc#4)11[sec]
Tip No. : (GARCO)719,721 Paint Output Pressuer: 8.8 - 11.8[MPa] Spray Speed : 70 - 100[cm/sec]
Thinner : GALBON S THINNER, Thinning: 0 - 5 % by Volume
Preceding Coats : The particular properties of this product require a very careful surface preparation of the steel which must be blast-cleaned to SSPC-SP 10 or ISO Sa 2.5.
Conditionof
Application
Subsequent Coats : Any one of our products and/or the equivalent, e.g. Inorganic zinc paint, Chlorinated rubber paint, Epoxy paint, Tar-epoxy paint
Packaging Two pack product
Notes VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
GALBON S-HB(GB S-HB)
Feb.2006
No. 6250
GALBON S-HB is an alcohol soluble inorganic zinc coating based on a combination of ethyl silicate and selected zinc dust. It gives excellent protection against corrosion and prolonged weather resistance, and is highly resistant to oil and solvent as well as fresh and salt water. GALBON S-HB withstands temperatures of up of to 400 degree C. A film thickness of 50-100 microns can be built in one application. GALBON S-HB is recommended as a top coating over GALBON S or WELBOND.
TECHNICAL DATA
Type Inorganic zinc silicate alcohol soluble and self-curing, high-build type
Recommened
Use
As a protective coating for oil tanks, solvent tanks, ballast tanks, outside hull, deck, heating pipes, holds, other steel structures, etc.
Mixing Ratio : Color :
Base : Powder = 7 : 3 [by volume]Grey
Flash Point : Base = 14.5, Powder = - [degC] Solid by volume : 60 ±2 [volume %] VOC : 464 [g/L] Coverage(Theoretical): 0.083 - 0.125 [L/m
2
]
Information
Film Thickness : WET 83 - 125 [micron]DRY 50 - 75 [micron]
() 5 oC 10 oC 20 oC 30 oC
Drying Time Surface Dry 40min. 30min. 20min. 10min.Hard Dry 6hrs. 5hrs. 4hrs. 3hrs.
Painting Interval Min 72hrs. 32hrs. 24hrs. 18hrs.Max - - - -
Pot Life 14hrs. 10hrs. 7hrs. 5hrs.
Method of Application : Airless spray; Brush (only for touch-up) Weather : Temperature : 0 - 50
degC, Humidity : 50 - 95 %R.H. For Airless Spray : Viscosity : 10 - 12[sec]
Tip No. : (GRACO)419,519 Paint Output Pressuer: 9.8[MPa]
Spray Speed : 60 - 80[cm/sec] Thinner : GALBON S-HB THINNER,
Thinning: 0 - 5 % by Volume Preceding Coats : GALBON S, GALBON SP, WELBOND, CERABOND
Conditionof
Application
Subsequent Coats : Any one of our products and/or the equivalent, e.g. Inorganic zinc paint, Chlorinated rubber paint, Epoxy paint, Tar-epoxy paint
Packaging Two pack product
Notes 1.In case an organic top coat is applied, dry film thickness of GALBON S-HB should be controlled at 50-100 microns. Recommended dry film thickness is 65 microns.2.Waiting time before the first cargo loading for Bulkcarrier(DRY CARGO) Temp. 10degC 20degC 30degC (Days) 7 7 73.Mixing Ratio,Base:Powder=25:75(by weight)
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
4.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
HIPER AC(HP AC)
Mar.2006
No. 4005
HIPER AC is a special synthetic resin paint giving a high-build quick drying, effective protection against corrosion. It possesses good sea water resistance and shows good adhesion to subsequent coats.
TECHNICAL DATA
Type Special synthetic resin anti-corrosive paint
Recommened
Use
Anti-corrosive paint for repair ships and steel ship's hull.
Color : S(Silver), SR(Silver red) Flash Point : 26.5 [degC] Solid by volume : 43 (+-2) [volume %] VOC : 538 [g/L] Coverage(Theoretical): 0.142 - 0.235 [L/m
2
]
Information
Film Thickness : WET 142 - 235 [micron]DRY 60 - 100 [micron]
() 5 oC 10 oC 20 oC 30 oC
Drying Time Surface Dry 1hr. 45mins. 30mins. 25mins.Hard Dry 8hrs. 6hrs. 4hrs. 3hrs.
Painting Interval Min (AC)(AF)
8hrs.12hrs.
6hrs.8hrs.
4hrs.6hrs.
3hrs.5hrs.
Max - - - -
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum -5
degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 1.6 Pa・s
Tip No. : (GRACO)621,623 Paint Output Pressuer: 11.7 - 14.7[MPa] Spray Speed : 60 - 80[cm/sec]
Thinner : RAVAX THINNER, Thinning: 0 - 5 % by Volume
Preceding Coats : EVABOND, NZ PRIMER, WELBOND, EPICON ZINC RICH PRIMER, etc.
Conditionof
Application
Subsequent Coats : TFA-10,TFA-10H, TFA FLAT, SEATENDER 12.15, SEA GRANDPRIX 500,1000, etc.
Packaging One pack product
Notes 1.Below 10 degC, extra solvent maybe required to obtain application viscosity.2.But too much solvent results in reduced sag resistance and paint film property.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
LZI PRIMER(LZI)
Feb.2006
No. 2100
LZI PRIMER, is an alkyd resin based primer . It dries quickly, offering effective rust-prevention and excellent resistance to impact and bending.
TECHNICAL DATA
Type Alkyd resin primer
Recommened
Use
As a rust-preventing primer for inside of superstructure, deck, hold, and other steel structures
Color : Red brown Flash Point : 43.0 [degC] Solid by volume : 52 (+-2) [volume %] VOC : 383 [g/L] Coverage(Theoretical): 0.058 - 0.077 [L/m
2
]
Information
Film Thickness : WET 58 - 77 [micron]DRY 30 - 40 [micron]
(D.F.T. 35micron) 0 oC 5 oC 10 oC 20 oC 30 oC
Drying Time Surface Dry 7hrs. 4hrs. 2hrs. 1hr. 30mins.Hard Dry 26hrs. 18hrs. 12hrs. 6hrs. 3hrs.
Painting Interval Min 45hrs. 30hrs. 20hrs. 16hrs. 10hrs.Max 120days 120days 100days 90days 60days
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum 0
degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : (Fc#4)120[sec]
Tip No. : (GRACO)719 Paint Output Pressuer: 10.7 - 13.8[MPa] Spray Speed : 80 - 100[cm/sec]
Thinner : MARINE THINNER, Thinning: 0 - 5 % by Volume
Preceding Coats : EVABOND, NZ PRIMER, etc.
Conditionof
Application
Subsequent Coats : EVAMARINE, Alkyd resin based paints
Packaging One pack product
Notes 1.Applying within the recommended film thickness range to avoid the wrinkling.2.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
LZI PRIMER ZR-HB(LZI ZR HB)
Feb.2006
No. 2104A
LZI PRIMER ZR-HB, based on alkali-resistant synthetic resin, contains special compound which can make zinc surface stable. It has excellent adhesion property on zinc rich shop primer, as well as salt-water and weathering resistance.
TECHNICAL DATA
Type Special synthetic resin primer
Recommened
Use
As the 1st coat of primer, when a conventional paint system is specified on zinc shop primer
Color : Red brown Flash Point : 36.0 [degC] Solid by volume : 52 (+-2) [volume %] VOC : 388 [g/L] Coverage(Theoretical): 0.058 - 0.135 [L/m
2
]
Information
Film Thickness : WET 58 - 135 [micron]DRY 30 - 70 [micron]
() 0 oC 5 oC 10 oC 20 oC 30 oC
Drying Time Surface Dry 10hrs. 6hrs. 3hrs. 1.5hrs. 45mins.Hard Dry 36hrs. 24hrs. 14hrs. 7hrs. 4hrs.
Painting Interval Min 70hrs. 48hrs. 30hrs. 20hrs. 16hrs.Max 120days 120days 100days 90days 60days
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum 0
degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 1 - 2Pa・s
Tip No. : (GRACO)719 Paint Output Pressuer: 14.7 - 17.7[MPa] Spray Speed : 70 - 90[cm/sec]
Thinner : MARINE THINNER, Thinning: 0 - 5 % by Volume
Preceding Coats : EVABOND, WELBOND, NZ PRIMER, etc.
Conditionof
Application
Subsequent Coats : EVAMARINE, EVAMARINE HB, Alkyd resin based paints
Packaging One pack product
Notes 1.Applying within the recommended film thickness range to avoid the wrinkling.2.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
LZI PRIMER ZS HB(LZI ZS HB)
Feb.2006
No. 2107
LZI PRIMER ZS HB, based on alkali-resistant synthetic resin, contains special compound which can make zinc surface stable. It has excellent adhesion property on zinc rich shop primer, as well as salt-water and weathering resistance.
TECHNICAL DATA
Type Special synthetic resin primer, High build
Recommened
Use
As the 1st coat of primer, when a conventional paint system is specified on zinc shop primer
Color : Red brown Flash Point : 31.0 [degC] Solid by volume : 43 (+-2) [volume %] VOC : 471 [g/L] Coverage(Theoretical): 0.069 - 0.162 [L/m
2
]
Information
Film Thickness : WET 70 - 162 [micron]DRY 30 - 70 [micron]
() 5 oC 10 oC 20 oC 30 oC
Drying Time Surface Dry 6hrs. 3hrs. 1.5hrs. 45mins.Hard Dry 24hrs. 14hrs. 7hrs. 4hrs.
Painting Interval Min 48hrs. 30hrs. 20hrs. 16hrs.Max 120days 100days 90days 60days
Method of Application : Airless spray; Brush*; Roller Weather : Temperature : Minimum 0
degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : (Fc#4)120[sec]
Tip No. : (GRACO)719 Paint Output Pressuer: 14.7 - 17.7[MPa] Spray Speed : 70 - 90[cm/sec]
Thinner : MARINE THINNER, Thinning: 0 - 5 % by Volume
Preceding Coats : EVABOND, WELBOND, EPICON ZINC RICH PRIMER, NZ PRIMER, etc.
Conditionof
Application
Subsequent Coats : LZI PRIMER, ROSWAN QD, HOLD SILVER, EVAMARINE, etc.
Packaging One pack product
Notes 1. * Sufficient thickness is difficult to obtain by brush.2.** In case of applying alkyd resin finish coat on LZI PRIMER ZS HB at outdoor exposed area or high humidity area , LZI PRIMER or ROSWN QD to be applied as a binder coat3.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
MARINE STAR 10 KAI(MS 10 KAI)
Mar.2006
No. 5865A
MARINE STAR 10 KAI is a tin free antifouling paint with self polishing action in service and long protection against marine organisms. The specific vehicle composition provides a unique hydration mechanism during operation , resulting in long lasting antifouling performance.
TECHNICAL DATA
Type Tin free self polishing antifouling paint
Recommened
Use
Antifouling paint on steel ship's bottom for world wide service with extended dry-docking interval.
Color : Pink, Red Flash Point : 23.0 [degC] Solid by volume : 55 (+-2) [volume %] VOC : 476 [g/L] Coverage(Theoretical): 0.18 - 0.27 [L/m
2
]
Information
Film Thickness : WET 182 - 273 [micron]DRY 100 - 150 [micron]
(D.F.T. 100micron) 5 oC 10 oC 20 oC 30 oC
Drying Time Surface Dry 3hrs. 2hrs. 1hr. 30mins.Hard Dry 12hrs. 8hrs. 5hrs. 4hrs.
Painting Interval Min 12hrs. 8hrs. 5hrs. 4hrs.Max - - - -
Dry to Launch Min 24hrs. 18hrs. 12hrs. 10hrs.
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum 0
degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : (Fc#4)90[sec]
Tip No. : (GRACO)621(721) - 635(735) Paint Output Pressuer: 11.7 - 14.7[MPa] Spray Speed : 60 - 80[cm/sec]
Thinner : RAVAX THINNER, Thinning: 0 - 5 % by Volume
Preceding Coats : SILVAX SQ-M, VINYL AC-HB, RAVAX AC HB, RAVAX AC-P, HIPER AC,
Conditionof
Application
Subsequent Coats : -
Packaging One pack product
Notes 1.There is a risk of antifoulings becoming fouled when ships are stationary for three consecutive weeks or more,particularly in areas with a high risk of fouling.2.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
MARINE STAR 20 KAI(MS 20 KAI)
Nov.2006
No. 5876B
MARINE STAR 20 KAI is a tin free antifouling paint with self polishing action in service and long protection against marine organisms. The specific vehicle composition provides a unique hydration mechanism during operation , resulting in long lasting antifouling performance.
TECHNICAL DATA
Type Tin free self polishing antifouling paint
Recommened
Use
Antifouling paint for steel ship's bottom
Color : Pink, Red Flash Point : 23.0 [degC] Solid by volume : 54 (+-2) [volume %] VOC : 462 [g/L] Coverage(Theoretical): 0.138 - 0.184 [L/m
2
]
Information
Film Thickness : WET 138 - 184 [micron]DRY 75 - 100 [micron]
() 5 oC 10 oC 20 oC 30 oC
Drying Time Surface Dry 3hrs. 2hrs. 1hr. 30mins.Hard Dry 12hrs. 8hrs. 5hrs. 4hrs.
Painting Interval Min 12hrs. 8hrs. 5hrs. 4hrs.Max - - - -
Dry to Launch Min 24hrs. 18hrs. 12hrs. 10hrs.
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum 0
degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : (Fc#4)90[sec]
Tip No. : (GRACO)621(721) - 635(735) Paint Output Pressuer: 11.7 - 14.7[MPa] Spray Speed : 60 - 80[cm/sec]
Thinner : RAVAX THINNER, Thinning: 0 - 5 % by Volume
Preceding Coats : SILVAX SQ-M, VINYL AC-HB, RAVAX AC HB, RAVAX AC-P, HIPER AC,
Conditionof
Application
Subsequent Coats : -
Packaging One pack product
Notes 1.There is a risk of antifoulings becoming fouled when ships are stationary for three consecutive weeks or more,particularly in areas with a high risk of fouling.2.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
MARINE STAR A(MS A)
Feb.2006
No. 5895
MARINE STAR A is a tin free erodible antifouling paint with self-polishing action in service and good protection against marine organisms. The specific vehicle composition provides a unique hydration mechanism during operation , resulting excellent antifouling peraformance.
TECHNICAL DATA
Type Tin free antifouling paint
Recommened
Use
Antifouling paint on aluminum ship's bottom
Color : Red, Blue, Red brown, White Flash Point : 22.0 [degC] Solid by volume : 54 (+-2) [volume %] VOC : 421 [g/L] Coverage(Theoretical): 0.186 [L/m
2
]
Information
Film Thickness : WET 186 [micron]DRY 100 [micron]
(D.F.T. 100micron) 5 oC 10 oC 20 oC 30 oC
Drying Time Surface Dry 3hrs. 2hrs. 1hr. 30mins.Hard Dry 12hrs. 8hrs. 5hrs. 4hrs.
Painting Interval Min 12hrs. 8hrs. 5hrs. 4hrs.Max -days -days -days -days
Dry to Launch Min 24hrs. 18hrs. 12hrs. 10hrs.
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum 0
degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : (Fc#4)90[sec]
Tip No. : (GRACO)619 - 625 Paint Output Pressuer: 11.7 - 14.7[MPa] Spray Speed : 60 - 80[cm/sec]
Thinner : RAVAX THINNER, Thinning: 0 - 5 % by Volume
Preceding Coats : VINYL AC-HB, RAVAX AC, RAVAX AC-P, HIPER AC, etc.
Conditionof
Application
Subsequent Coats : -
Packaging One pack product
Notes 1.There is a risk of antifoulings becoming fouled when ships are stationary for three consecutive weeks or more,particularly in areas with a high risk of fouling.2.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
MARINE STAR FLAT S(MS FLAT S)
Mar.2006
No. 5868S
MARINE STAR FLAT S is a tin free antifouling paint with self polishing action. The product is used for fouling control on the flat bottom.
TECHNICAL DATA
Type Tin free self polishing antifouling paint
Recommened
Use
Antifouling paint on steel ships' flat bottom for world wide service with extended drydocking interval.
Color : Pink, Red Flash Point : 23.0 [degC] Solid by volume : 52 (+-2) [volume %] VOC : 457 [g/L] Coverage(Theoretical): 0.095 - 0.19 [L/m
2
]
Information
Film Thickness : WET 95 - 190 [micron]DRY 50 - 100 [micron]
() 5 oC 10 oC 20 oC 30 oC
Drying Time Surface Dry 3hrs. 2hrs. 1hr. 30mins.Hard Dry 12hrs. 8hrs. 5hrs. 4hrs.
Painting Interval Min 12hrs. 8hrs. 5hrs. 4hrs.Max - - - -
Dry to Launch Min 24hrs. 18hrs. 12hrs. 10hrs.
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum 0
degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : (Fc#4)90[sec]
Tip No. : (GRACO)621(721) - 633(733) Paint Output Pressuer: 11.7 - 14.7[MPa] Spray Speed : 60 - 80[cm/sec]
Thinner : RAVAX THINNER, Thinning: 0 - 5 % by Volume
Preceding Coats : SILVAX SQ, VINYL AC-HB, RAVAX AC-P, RAVAX AC, RAVAX AC-HB,
Conditionof
Application
Subsequent Coats : -
Packaging One pack product
Notes 1.There is a risk of antifoulings becoming fouled when ships are stationary for three consecutive weeks or more,particularly in areas with a high risk of fouling.2.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
MAXSTOP G(MXT G)
Dec.2006
No. 6437
MAXSTOP G is a high-build epoxy non-slip paint. It has excellent physical properties such as adhesion, toughness, impact and abrasion resistance, and chemical resistance to water, salt water and oils. No repainting is required for long time. It is suitable for non-slip deck.
TECHNICAL DATA
Type Epoxy paint, high-build
Recommened
Use
Non-slip deck coating
Mixing Ratio : Color :
Base : Hardener = 82 : 18 [by volume]Red brown, Green, Grey
Flash Point : Base = 34.0, Hardener = 29.3 [degC] Specific Gravity : 1.81 [g/mL] Solid by volume : 75 ±2 [volume %] VOC : 233 [g/L] Coverage(Theoretical): 1.07 [L/m
2
]
Information
Film Thickness : WET 1066 [micron]DRY 800 [micron]
() 5 oC 10 oC 20 oC 30 oC
Drying Time Surface Dry 3.5hrs. 2.5hrs. 1.5hrs. 1hr.Hard Dry 42hrs. 28hrs. 14hrs. 9hrs.
Painting Interval Min 42hrs. 28hrs. 14hrs. 9hrs.Max - - - -
Pot Life 7hrs. 5hrs. 4hrs. 2hrs.
Method of Application : Special spray equipment, Roller, Brush, Spatula Weather : Temperature : Minimum 5
degC, Humidity : Maximum 85 %R.H. Thinner : MAXSTOP THINNER, EPICON MARINE THINNER
Thinning: % by Volume Preceding Coats : BANNOH 500, EPICON ZINC HB-2
Conditionof
Application
Subsequent Coats :
Packaging Two pack product
Notes
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
NEW MARINE GOLD DX(NMG DX)
Feb.2006
No. 5897
NEW MARINE GOLD DX is a tin free self polishing antifouling paint based on the specific polymer with highly hydrolysis activity. Excellent antifouling effect is derived from the highly active polymer which ensures maximum effectiveness and leaching of the biocides. Activation at the surface is maintained by control of hydrolysis thus providing long term antifouling protection commensurate with applied film thickness.
TECHNICAL DATA
Type Tin free self polishing antifouling paint
Recommened
Use
Antifouling paint on FRP,aluminium and steel ship's bottom .
Color : Red , Blue, Red brown, White Flash Point : 24 [degC] Solid by volume : 40 (+-2) [volume %] VOC : 530 [g/L] Coverage(Theoretical): 0.12 - 0.25 [L/m
2
]
Information
Film Thickness : WET 124 - 262 [micron]DRY 50 - 100 [micron]
(D.F.T. 50micron) 5 oC 10 oC 20 oC 30 oC
Drying Time Surface Dry 3hrs. 2hrs. 1hr. 30min.Hard Dry 6hrs. 5hrs. 4hrs. 3hrs.
Painting Interval Min 6hrs. 5hrs. 4hrs. 3hrs.Max
Dry to Launch Min 8hrs. 7hrs. 6hrs. 5hrs.
Method of Application : Air spray; Brush; Roller Weather : Temperature : Minimum 0
degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : (Fc#4)90[sec]
Tip No. : (GRACO)619 - 625 Paint Output Pressuer: 11.7 - 14.7[MPa] Spray Speed : 60 - 80[cm/sec]
Thinner : RAVAX THINNER, Thinning: 0 - 5 % by Volume
Preceding Coats : FRP PRIMER, VINYL AC-HB, HIPER AC, RAVAX AC-HB, SILVAX SQ-K,
Conditionof
Application
Subsequent Coats : -
Packaging One pack product
Notes VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
NEW MARINE GOLD(NMG)
Feb.2006
No. 5896
NEW MARINE GOLD is a tin free erodible antifouling paint with self-polishing action in service and good protection against marine organisms. The specific vehicle composition provides a unique hydration mechanism during operation , resulting excellent antifouling performance.
TECHNICAL DATA
Type Tin free antifouling paint
Recommened
Use
Antifouling paint on FRP ship's bottom
Color : Red, White, Blue, Red brown Flash Point : 22.0 [degC] Solid by volume : 54 (+-2) [volume %] VOC : 428 [g/L] Coverage(Theoretical): 0.093 - 0.186 [L/m
2
]
Information
Film Thickness : WET 93 - 186 [micron]DRY 50 - 100 [micron]
(D.F.T. 50micron) 5 oC 10 oC 20 oC 30 oC
Drying Time Surface Dry 3hrs. 2hrs. 1hr. 30mins.Hard Dry 6hrs. 5hrs. 4hrs. 3hrs.
Painting Interval Min 6hrs. 5hrs. 4hrs. 3hrs.Max - - - -
Dry to Launch Min 8hrs. 7hrs. 6hrs. 5hrs.
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum 0
degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : (Fc#4)90[sec]
Tip No. : (GRACO)619 - 625 Paint Output Pressuer: 11.7 - 14.7[MPa] Spray Speed : 60 - 80[cm/sec]
Thinner : RAVAX THINNER, Thinning: 0 - 5 % by Volume
Preceding Coats : FRP PRIMER
Conditionof
Application
Subsequent Coats : -
Packaging One pack product
Notes VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
NOVA 1000(NV 1000)
Apr.2006
No. 6180
NOVA 1000, is Tar free modified epoxy paint, based on modified epoxy, pigmentation. It gives excellent physical properties such as adhesion, toughness and abrasion resistance, etc. and chemical resistance to water, and salt water and oils. It is suitable for protection of water tank interior.
TECHNICAL DATA
Type Tar free modified epoxy paint
Recommened
Use
Ballast water tank, Crude oil tank, Cargo hold, Void space, Cofferdam
Mixing Ratio : Color :
Base : Hardener = 78 : 22 [by volume]Light grey, Cream
Flash Point : Base = 25.5, Hardener = 24.9 [degC] Solid by volume : 66 (+-2) [volume %] VOC : 378 [g/L] Coverage(Theoretical): 0.189 - 0.379 [L/m
2
]
Information
Film Thickness : WET 189 - 378 [micron]DRY 125 - 250 [micron]
(D.F.T. 250micron) 10 oC 20 oC 30 oC
Drying Time Surface Dry 7hrs. 4hrs. 2hrs.Hard Dry 28hrs. 15hrs. 10hrs.
Painting Interval Min 28hrs. 15hrs. 10hrs.Max 15days 10days 7days
Pot Life 10hrs. 6hrs. 4hrs.
Method of Application : Airless spray Weather : Temperature : Minimum 10
degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 1.5 - 2.0 Pa・s
Tip No. : (GRACO)621,623 Paint Output Pressuer: 14.7 - 17.7[MPa] Spray Speed : 60 - 80[cm/sec]
Thinner : EPICON MARINE THINNER, Thinning: 0 - 7 % by Volume
Preceding Coats : WELBOND, NZ PRIMER, EPICON ZINC RICH PRIMER, CERABOND
Conditionof
Application
Subsequent Coats : -
Packaging Two pack product
Notes 1.In confined spaces such as tank insides, ventilation is required during application and curing to remove solvent vapours and promote curing.2.If there is a possibility that the painted surface will be in direct sunlight, the succeeding coat should be applied as soon as possible after the minimum painting interval.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
NOVA 1000 QD(NV 1000 QD)
Apr.2006
No. 6180A
NOVA 1000 QD, is Tar free modified epoxy paint, based on modified epoxy, pigmentation. It gives excellent physical properties such as adhesion, toughness and abrasion resistance, etc. and chemical resistance to water and salt water and oils. It is suitable for protection of water tank interior.
TECHNICAL DATA
Type Tar free modified epoxy paint
Recommened
Use
Ballast water tank, Crude oil tank, Cargo hold, Void space, Cofferdam
Mixing Ratio : Color :
Base : Hardener = 78 : 22 [by volume]Light Grey, Cream
Flash Point : Base = 25.5, Hardener = 24.9 [degC] Solid by volume : 67 (+-2) [volume %] VOC : 373 [g/L] Coverage(Theoretical): 0.187 - 0.373 [L/m
2
]
Information
Film Thickness : WET 187 - 373 [micron]DRY 125 - 250 [micron]
(D.F.T. 250micron) -5 oC 0 oC 5 oC 10 oC 20 oC 30 oC
Drying Time Surface Dry 16hrs. 11hrs. 7hrs. 4hrs. 2hrs.Hard Dry 37hrs. 30hrs. 20hrs. 15hrs. 7hrs.
Painting Interval Min 40hrs. 33hrs. 24hrs. 18hrs. 10hrs.Max 15day 15days 15days 10days 7days
Pot Life 6hrs. 5hrs. 3hrs.
Method of Application : Airless spray Weather : Temperature : -5 - 20
degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 1.5 - 2.0 Pa・s
Tip No. : (GRACO)621,623 Paint Output Pressuer: 14.7 - 17.7[MPa] Spray Speed : 60 - 80[cm/sec]
Thinner : EPICON MARINE THINNER, Thinning: 0 - 15 % by Volume
Preceding Coats : WELBOND, CERABOND, EPICON ZINC RICH PRIMER, NZ PRIMER
Conditionof
Application
Subsequent Coats : -
Packaging Two pack product
Notes 1.In confined spaces such as tank insides or low temperature condition, ventilation is required during application and curing to remove solvent vapours and promote curing. 2.If there is a possibility that the painted surface will be in direct sunlight, the succeeding coat should be applied, as soon as possible after the minimum painting interval.3.The temperature of the mixed base and hardener preferably should be above 10 degC otherwise extra solvent may be required to obtain appliaction viscosity.4.Too much solvent results in reduced sag resistance and paint film property.5.Application at temperatures down to -5 degC is possible but curing to hardeness takes longer and complete cure will be reached when temperature increases.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
NOVA 2000(NV 2000)
Mar.2007
No. 6181
NOVA 2000, is Tar free high solid modified epoxy paint, based on modified epoxy, pigmentation. It gives excellent physical properties such as adhesion, toughness and abrasion resistance, etc. and chemical resistance to water, salt water and oils. It is suitable for protection of water tank interior.
TECHNICAL DATA
Type Tar free high solid modified epoxy paint
Recommened
Use
Ballast water tank, Crude oil tank, Void space, Cofferdam,
Mixing Ratio : Color :
Base : Hardener = 83 : 17 [by volume]Light Grey, Cream, Red brown
Flash Point : Base = 37.0, Hardener = 21.5 [degC] Specific Gravity : 1.4 [g/mL] Solid by volume : 80 (+-2) [volume %] VOC : 303 [g/L] Coverage(Theoretical): 0.16 - 0.31 [L/m
2
]
Information
Film Thickness : WET 156 - 313 [micron]DRY 125 - 250 [micron]
(D.F.T. 250micron) 10 oC 20 oC 30 oC
Drying Time Surface Dry 12hrs. 6hrs. 4hrs.Hard Dry 24hrs. 15hrs. 12hrs.
Painting Interval Min 24hrs. 15hrs. 12hrs.Max 15days 10days 7days
Pot LifeDry to Launch Min
5hrs.8days
3hrs.6days
2hrs.4days
Method of Application : Airless spray Weather : Temperature : 10 - 40
degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 1.5 - 2.0 Pa・s
Tip No. : (GRACO)621,623 Paint Output Pressuer: 14.7 - 17.7[MPa] Spray Speed : 60 - 80[cm/sec]
Thinner : EPICON MARINE THINNER, Thinning: 0 - 7 % by Volume
Preceding Coats : WELBOND, CERABOND, EPICON ZINC RICH PRIMER, NZ PRIMER
Conditionof
Application
Subsequent Coats : -
Packaging Two pack product
Notes 1.In confined spaces such as tank insides, ventilation is required during application and curing to remove solvent vapours and promote curing. 2.If there is a possibility that the painted surface will be in direct sunlight, the succeeding coat should be applied, as soon as possible after the minimum painting interval.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
NOVA 2000 CH QD(NV 2000 CH QD)
Mar.2006
No. 6181I
NOVA 2000 CH QD, is Tar free high solid modified epoxy paint, based on a combination ofmodified epoxy, special abrasive resistant agent. It gives excellent physical properties such as adhesion, toughness and abrasion resistance, etc. and rust-prevention. It is suitable for protection of holds of steel ships.
TECHNICAL DATA
Type Tar free high solid modified epoxy paint
Recommened
Use
Cargo hold
Mixing Ratio : Color :
Base : Hardener = 80 : 20 [by volume]Light Grey, Red brown
Flash Point : Base = 30.0, Hardener = 21.5 [degC] Solid by volume : 80 (+-2) [volume %] VOC : 298 [g/L] Coverage(Theoretical): 0.16 - 0.31 [L/m
2
]
Information
Film Thickness : WET 156 - 313 [micron]DRY 125 - 250 [micron]
(D.F.T. 200micron) 5 oC 10 oC 20 oC 30 oC
Drying Time Surface Dry 8hrs. 4hrs. 2hrs.Hard Dry 24hrs. 17hrs. 7hrs.
Painting Interval Min 24hrs. 17hrs. 7hrs.Max 15days 10days 7days
Pot Life 5hrs. 3hrs. 2hrs.
Method of Application : Airless spray Weather : Temperature : 0 - 20
degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 1.5 - 2.0 Pa・s
Tip No. : (GRACO)621,623 Paint Output Pressuer: 14.7 - 17.7[MPa] Spray Speed : 60 - 80[cm/sec]
Thinner : NOVA THINNER, Thinning: 0 - 15 % by Volume
Preceding Coats : WELBOND, CERABOND, EPICON ZINC RICH PRIMER, NZ PRIMER
Conditionof
Application
Subsequent Coats : -
Packaging Two pack product
Notes 1.In confined spaces such as tank insides or low temperature condition, ventilation is required during application and curing to remove solvent vapours and promote curing. 2.If there is a possibility that the painted surface will be in direct sunlight, the succeeding coat should be applied, as soon as possible after the minimum painting interval.3.The temperature of the mixed base and hardener preferably should be above 10 degC otherwise extra solvent may be required to obtain appliaction viscosity.4.Too much solvent results in reduced sag resistance and paint film property.5.Application at temperatures down to 0 degC is possible but curing to hardeness takes longer and complete cure will be reached when temperature increases.6.This product can not be applied to the grain as FDA-DRY CARGO
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
7.Wating time before the first cargo loading TEMP 5degC 10degC 20degC Days(DFT200micron) 25 16 10 Days(DFT400micron) 35 24 158.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
NOVA 2000 CH(NV 2000 CH)
Mar.2006
No. 6181H
NOVA 2000 CH, is Tar free high solid modified epoxy paint, based on a combination of modified epoxy, special abrasive resistant agent. It gives excellent physical properties such as adhesion, toughness and abrasion resistance, etc. and rust-prevention. It is suitable for protection of cargo hold.
TECHNICAL DATA
Type Tar free high solid modified epoxy paint
Recommened
Use
Cargo hold
Mixing Ratio : Color :
Base : Hardener = 80 : 20 [by volume]Light Grey, Red brown
Flash Point : Base = 30.0, Hardener = 21.5 [degC] Solid by volume : 80 (+-2) [volume %] VOC : 303 [g/L] Coverage(Theoretical): 0.16 - 0.31 [L/m
2
]
Information
Film Thickness : WET 156 - 313 [micron]DRY 125 - 250 [micron]
(D.F.T. 200micron) 10 oC 20 oC 30 oC
Drying Time Surface Dry 12hrs. 6hrs. 4hrs.Hard Dry 24hrs. 15hrs. 12hrs.
Painting Interval Min 24hrs. 15hrs. 12hrs.Max 15days 10days 7days
Pot Life 5hrs. 3hrs. 2hrs.
Method of Application : Airless spray Weather : Temperature : Minimum 10
degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 1.5 - 2.0 Pa・s
Tip No. : (GRACO)621,623 Paint Output Pressuer: 14.7 - 17.7[MPa] Spray Speed : 60 - 80[cm/sec]
Thinner : EPICON MARINE THINNER, Thinning: 0 - 7 % by Volume
Preceding Coats : WELBOND, CERABOND, EPICON ZINC RICH PRIMER, NZ PRIMER
Conditionof
Application
Subsequent Coats : -
Packaging Two pack product
Notes 1.In confined spaces such as tank insides, ventilation is required during application and curing to remove solvent vapours and promote curing. 2.If there is a possibility that the painted surface will be in direct sunlight, the succeeding coat should be applied, as soon as possible after the minimum painting interval.3.This product can not be applied to the grain as FDA-DRY CARGO4.Wating time before the first cargo loading TEMP 10degC 20degC 30degC Days(DFT200micron) 20 12 7 Days(DFT400micron) 30 16 105.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
NOVA 2000 GF QD(NV 2000 GF QD)
Mar.2006
No. 6181F
NOVA 2000 GF QD, is Tar free high solid modified epoxy paint, based on a combination of modified epoxy and glass-flake. It gives excellent physical properties such as adhesion, toughness and abrasion resistance, and rust-prevention. It is suitable for protection of cargo hold.
TECHNICAL DATA
Type Tar free high solid modified epoxy paint
Recommened
Use
Cargo hold
Mixing Ratio : Color :
Base : Hardener = 80 : 20 [by volume]Light Grey, Red brown
Flash Point : Base = 30.0, Hardener = 21.5 [degC] Solid by volume : 80 (+-2) [volume %] VOC : 298 [g/L] Coverage(Theoretical): 0.16 - 0.31 [L/m
2
]
Information
Film Thickness : WET 156 - 313 [micron]DRY 125 - 250 [micron]
(D.F.T. 200micron) 5 oC 10 oC 20 oC 30 oC
Drying Time Surface Dry 8hrs. 4hrs. 2hrs.Hard Dry 24hrs. 17hrs. 7hrs.
Painting Interval Min 24hrs. 17hrs. 7hrs.Max 15days 10days 7days
Pot Life 5hrs. 3hrs. 2hrs.
Method of Application : Airless spray Weather : Temperature : 0 - 20
degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 1.5 - 2.0 Pa・s
Tip No. : (GRACO)621,623 Paint Output Pressuer: 14.7 - 17.7[MPa] Spray Speed : 60 - 80[cm/sec]
Thinner : NOVA THINNER, Thinning: 0 - 15 % by Volume
Preceding Coats : WELBOND, CERABOND, EPICON ZINC RICH PRIMER, NZ PRIMER
Conditionof
Application
Subsequent Coats : -
Packaging Two pack product
Notes 1.In confined spaces such as tank insides or low temperature condition, ventilation is required during application and curing to remove solvent vapours and promote curing. 2.If there is a possibility that the painted surface will be in direct sunlight, the succeeding coat should be applied, as soon as possible after the minimum painting interval.3.The temperature of the mixed base and hardener preferably should be above 10 degC otherwise extra solvent may be required to obtain appliaction viscosity.4.Too much solvent results in reduced sag resistance and paint film property.5.Application at temperatures down to 0 degC is possible but curing to hardeness takes longer and complete cure will be reached when temperature increases.6.This product can not be applied to the grain as FDA-DRY CARGO.7.Wating time before the first cargo loading
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
TEMP 5degC 10degC 20degC Days(DFT200micron) 25 16 10 Days(DFT400micron) 35 24 158.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
NOVA 2000 GF(NV 2000 GF)
Jan.2007
No. 6181G
NOVA 2000 GF, is Tar free high solid modified epoxy paint, based on a combination of modified epoxy and glass-flake. It gives excellent physical properties such as adhesion, toughness and abrasion resistance, and rust-prevention. It is suitable for protection of cargo hold.
TECHNICAL DATA
Type Tar free high solid modified epoxy paint
Recommened
Use
Cargo hold
Mixing Ratio : Color :
Base : Hardener = 80 : 20 [by volume]Light Grey, Red Brown
Flash Point : Base = 37.0, Hardener = 21.5 [degC] Solid by volume : 80 (+-2) [volume %] VOC : 275 [g/L] Coverage(Theoretical): 0.156 - 0.313 [L/m
2
]
Information
Film Thickness : WET 156 - 313 [micron]DRY 125 - 250 [micron]
(D.F.T. 250micron) 10 oC 20 oC 30 oC
Drying Time Surface Dry 12hrs. 6hrs. 4hrs.Hard Dry 24hrs. 15hrs. 12hrs.
Painting Interval Min 24hrs. 15hrs. 12hrs.Max 15days 10days 7days
Pot Life 5hrs. 3hrs. 2hrs.
Method of Application : Airless spray Weather : Temperature : Minimum 10
degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 1.5 - 2.0 Pa・s
Tip No. : (GRACO)621,623 Paint Output Pressuer: 14.7 - 17.7[MPa] Spray Speed : 60 - 80[cm/sec]
Thinner : EPICON MARINE THINNER, Thinning: 0 - 7 % by Volume
Preceding Coats : WELBOND, CERABOND, EPICON ZINC RICH PRIMER, NZ PRIMER
Conditionof
Application
Subsequent Coats : -
Packaging Two pack product
Notes 1.In confined spaces such as tank insides, ventilation is required during application and curing to remove solvent vapours and promote curing. 2.If there is a possibility that the painted surface will be in direct sunlight, the succeeding coat should be applied, as soon as possible after the minimum painting interval.3.This product can not be applied to the grain as FDA-DRY CARGO4.Wating time before the first cargo loading TEMP 10degC 20degC 30degC Days(DFT200micron) 20 12 7 Days(DFT400micron) 30 16 105.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
NOVA 2000 QD(NV 2000 QD)
Feb.2006
No. 6181A
NOVA 2000 QD, is Tar free high solid modified epoxy paint, based on modified epoxy, pigmentation. It gives excellent physical properties such as adhesion, toughness and abrasion resistance, etc. and chemical resistance to water, salt water and oils. It is suitable for protection of water tank interior.
TECHNICAL DATA
Type Tar free high solid modified epoxy paint
Recommened
Use
Ballast water tank, Crude oil tank, Cargo hold, Void space, Cofferdam,
Mixing Ratio : Color :
Base : Hardener = 83 : 17 [by volume]Light Grey, Cream, Red brown
Flash Point : Base = 37.0, Hardener = 21.5 [degC] Solid by volume : 80 (+-2) [volume %] VOC : 298 [g/L] Coverage(Theoretical): 0.16 - 0.31 [L/m
2
]
Information
Film Thickness : WET 156 - 313 [micron]DRY 125 - 250 [micron]
(D.F.T. 250micron) -5 oC 0 oC 5 oC 10 oC 20 oC 30 oC
Drying Time Surface Dry 17hrs. 12hrs. 8hrs. 4hrs. 2hrs.Hard Dry 44hrs. 35hrs. 24hrs. 17hrs. 7hrs.
Painting Interval Min 44hrs. 35hrs. 24hrs. 17hrs. 7hrs.Max 15days 15days 15days 10days 7days
Pot Life 5hrs. 3hrs. 2hrs.
Method of Application : Airless spray Weather : Temperature : 0 - 20
degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 1.5 - 2.0 Pa・s
Tip No. : (GRACO)621,623 Paint Output Pressuer: 14.7 - 17.7[MPa] Spray Speed : 60 - 80[cm/sec]
Thinner : NOVA THINNER, Thinning: 0 - 15 % by Volume
Preceding Coats : WELBOND, CERABOND, EPICON ZINC RICH PRIMER, NZ PRIMER
Conditionof
Application
Subsequent Coats : -
Packaging Two pack product
Notes 1.In confined spaces such as tank insides or low temperature condition, ventilation is required during application and curing to remove solvent vapours and promote curing. 2.If there is a possibility that the painted surface will be in direct sunlight, the succeeding coat should be applied, as soon as possible after the minimum painting interval.3.The temperature of the mixed base and hardener preferably should be above 10 degC otherwise extra solvent may be required to obtain appliaction viscosity.4.Too much solvent results in reduced sag resistance and paint film property.5.Application at temperatures down to 0 degC is possible but curing to hardeness takes longer and complete cure will be reached when temperature increases.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
NOVA 2000 W QD(NV 2000 W QD)
Mar.2007
No. 6181D
NOVA 2000 W QD, is Tar free high solid modified epoxy paint, based on modified epoxy, pigmentation. It gives excellent physical properties such as adhesion, toughness and abrasion resistance, etc. and chemical resistance to water, salt water and oils. It is suitable for protection of water tank interior.
TECHNICAL DATA
Type Tar free high solid modified epoxy paint
Recommened
Use
Ballast water tank, Crude oil tank, Cargo hold, Void space, Cofferdam,
Mixing Ratio : Color :
Base : Hardener = 83 : 17 [by volume]Light Grey, Cream, Red brown
Flash Point : Base = 26, Hardener = 22.5 [degC] Solid by volume : 76 (+-2) [volume %] VOC : 307 [g/L] Coverage(Theoretical): 0.164 - 0.329 [L/m
2
]
Information
Film Thickness : WET 164 - 329 [micron]DRY 125 - 250 [micron]
(D.F.T. 250micron) -5 oC 0 oC 5 oC 10 oC 20 oC 30 oC
Drying Time Surface Dry 15hrs. 10hrs. 7hrs. 4hrs. 2hrs.Hard Dry 40hrs. 26hrs. 18hrs. 15hrs. 6hrs.
Painting Interval Min 40hrs. 26hrs. 18hrs. 15hrs. 6hrs.Max 15days 15days 15days 10days 7days
Pot Life 6hrs. 4hrs. 2.5hrs. 1.5hrs.
Method of Application : Airless spray Weather : Temperature : 0 - 15
degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 1.5 - 2.0 Pa・s
Tip No. : (GRACO)621,623 Paint Output Pressuer: 14.7 - 17.7[MPa] Spray Speed : 60 - 80[cm/sec]
Thinner : NOVA THINNER, Thinning: 0 - 7 % by Volume
Preceding Coats : WELBOND, CERABOND, EPICON ZINC RICH PRIMER, NZ PRIMER
Conditionof
Application
Subsequent Coats : -
Packaging Two pack product
Notes 1.In confined spaces such as tank insides or low temperature condition, ventilation is required during application and curing to remove solvent vapours and promote curing. 2.If there is a possibility that the painted surface will be in direct sunlight, the succeeding coat should be applied, as soon as possible after the minimum painting interval.3.The temperature of the mixed base and hardener preferably should be above 10 degC otherwise extra solvent may be required to obtain appliaction viscosity.4.Too much solvent results in reduced sag resistance and paint film property.5.Application at temperatures down to 0 degC is possible but curing to hardeness takes longer and complete cure will be reached when temperature increases.6.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
NOVA 5000(NV 5000)
Feb.2006
No. 6182
NOVA 5000, solvent-free epoxy tank coating, is designed as a protective coating of ballast water tanks and cargo oil tanks. It has excellent water/sea-water resistance and has also superior crude oil resistance. NOVA 5000 is eco-friendly to the environment as it contains no solvent, no heavy metal. NOVA 5000 can be coated by conventional airless spray.
TECHNICAL DATA
Type Solventfree epoxy coating
Recommened
Use
Ballast water tank, Crude oil tank, void space, cofferdam, hold, of ships. bridges, underground pipes, port facilities, etc.
Mixing Ratio : Color :
Base : Hardener = 83 : 17 [by volume]Light Grey
Flash Point : Base = >250, Hardener = 155 [degC] Solid by volume : 100 (+-2) [volume %] VOC : 122 [g/L] Coverage(Theoretical): 0.3 [L/m
2
]
Information
Film Thickness : WET 300 [micron]DRY 300 [micron]
(D.F.T. 300micron) 10 oC 20 oC 30 oC
Drying Time Surface Dry 45hrs. 18hrs. 11hr.Hard Dry 3days. 24hrs. 16hrs.
Painting Interval Min 3days 24hrs. 16hrs.Max 14days 14days 14days
Pot Life 1.5hrs. 1hr. 45min.
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum 10
degC, Humidity : Maximum 85 %R.H. For Airless Spray :
Tip No. : (GRACO)619 - 721 Paint Output Pressuer: 23.5 - 33.4[MPa]
Spray Speed : 60 - 80[cm/sec] Thinner : EPICON MARINE THINNER ( for cleaning purpose),
Thinning: - % by Volume Preceding Coats : WELBOND, CERABOND, EPICON ZINC RICH PRIMER, NZ PRIMER
Conditionof
Application
Subsequent Coats : -
Packaging Two pack product
Notes
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
NOVA 5000 BARRIER(NV 5000 B)
Feb.2006
No. 6182A
NOVA 5000 BARRIER, solvent-free epoxy putty, is designed as a repair protective coating of ballast water tanks and cargo oil tanks. It has excellent water/sea-water resistance and has also superior crude oil resistance, besides excellent adhesion even on simply treated or/and slightly dump surface. NOVA 5000 BARRIER is eco-friendly to the environment as it is solvent-free.
TECHNICAL DATA
Type Solvent-free epoxy putty for repair
Recommened
Use
Ballast water tank, Void space, Cofferdam, Hold of ships, Bridges, Underground pipes, Port facilities, etc.
Mixing Ratio : Color :
Base : Hardener = 55 : 45 [by volume]Grey
Flash Point : Base = >250, Hardener = 155 [degC] Solid by volume : 100 (+-2) [volume %] VOC : 195 [g/L] Coverage(Theoretical): 0.3 [L/m
2
]
Information
Film Thickness : WET 300 [micron]DRY 300 [micron]
(D.F.T. 300micron) 5 oC 10 oC 20 oC 30 oC
Drying Time Surface Dry 8hrs. 4hrs. 2hr.Hard Dry 24hrs. 12hrs. 8hrs.
Painting Interval Min 24hrs. 12hrs. 8hrs.Max 7days 7days 7days
Pot LifeDry to Launch Min
1hrs.18hrs.
40min8hrs.
30min.6hrs.
Method of Application : Brush; Roller; Spatula; Hand-glove Weather : Temperature : -
degC, Humidity : - Thinner : EPICON MARINE THINNER ( for cleaning only),
Thinning: Not recommended. % by Volume Preceding Coats : -
Conditionof
Application
Subsequent Coats : -
Packaging Two pack product
Notes
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
NZ PRIMER S(NZ S)
Feb.2006
No. 1050
NZ PRIMER S, based on a combination of epoxy resin, rust-preventive pigments and hardener, is quick drying and gives adequate preliminary protection of blast-cleaned steel plates. It is compatible with almost any type of priming coat and highly resistant to heat, oil, water and solvents.
TECHNICAL DATA
Type Non zinc type epoxy shop primer
Recommened
Use
As a shop primer for protection of blast- cleaned steel plates. Especially suitable for steel plates subject to prolonged weathering
Mixing Ratio : Color :
Base : Hardener = 73 : 27 [by volume]Red brown
Flash Point : Base = 3.5, Hardener = 7.0 [degC] Solid by volume : 23 [volume %] VOC : 655 [g/L] Coverage(Theoretical): 0.091 [L/m
2
]
Information
Film Thickness : DRY 22 [micron]
(D.F.T. 22micron) 5 oC 10 oC 20 oC 30 oC
Drying Time Surface Dry 8mins. 7mins. 4mins. 3mins.Hard Dry 4hrs. 3hrs. 2hrs. 1hr.
Painting Interval Min 24hrs. 20hrs. 16hrs. 8hrs.Max 150days 120days 120days 90days
Pot Life 72hrs. 72hrs. 48hrs. 24hrs.
Method of Application : Airless spray, Brush Weather : Temperature : Minimum 5
degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : (IWATA CUP)9 - 10[sec]
Tip No. : (GRACO)719 Paint Output Pressuer: 8.8 - 11.8[MPa] Spray Speed : 80 - 120[cm/sec]
Thinner : EPICON MARINE THINNER, Thinning: 10 - 25 % by Volume
Preceding Coats : -
Conditionof
Application
Subsequent Coats : Any one of our products and/or the equivalent ,e.g.:, Oleoresinous paint, Chlorinated rubber paint, Vinyl paint, Epoxy paint, Tar-epoxy paint
Packaging Two pack product
Notes 1.Expected life for outdoor exposure[ under normal conditions ] : about 4 months2.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
PERMAX No.3000 S W(PM 3000S W)
Feb.2006
No. 6050A
PERMAX No.3000 S W, based on a combination of epoxy resin with glass-flake and polyamide resin, has excellent physical properties such as adhesion, toughness and abrasion resistance, etc., and chemical resistance to salt water, fresh water, crude oil, alkalis and weak acids. It is suitable for protective coating of splash zones, underwater areas and tank interiors. A film thickness of over 500 microns can be built in one application by airless spray.
TECHNICAL DATA
Type Epoxy/polyamide glass flake mastic paint
Recommened
Use
Splash zone and underwater area of ship's outer shell and offshore structures
Mixing Ratio : Color :
Base : Hardener = 79 : 21 [by volume]Grey, Red brown, Black
Flash Point : Base = 28.5, Hardener = 50 [degC] Solid by volume : 92 (+-2) [volume %] VOC : 151 [g/L] Coverage(Theoretical): 0.326 - 0.543 [L/m
2
]
Information
Film Thickness : WET 326 - 543 [micron]DRY 300 - 500 [micron]
() 5 oC 10 oC 20 oC 30 oC
Drying Time Surface Dry 12hrs. 6hrs.Hard Dry 32hrs. 16hrs.
Painting Interval Min 28hrs. 16hrs.Max 5days 4days
Pot Life 4hrs. 2hrs.
Method of Application : Airless spray; Brush Weather : Temperature : Minimum 5
degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 6.0[sec]
Tip No. : (GRACO)Zincgun(208-663) Paint Output Pressuer: 24.5 - 29.4[MPa] Spray Speed : 60 - 80[cm/sec]
Thinner : EPICON MARINE THINNER, Thinning: 0 - 3 % by Volume
Preceding Coats : BANNOH 500, BANNOH 2000
Conditionof
Application
Subsequent Coats : BANNOH 500 N, VINYL AC-HB, etc.
Packaging Two pack product
Notes
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
PERMAX No.3000 S(PM 3000S)
Feb.2006
No. 6050
PERMAX No.3000 S, based on a combination of epoxy resin with glass-flake and polyamide resin, has excellent physical properties such as adhesion, toughness and abrasion resistance, etc., and chemical resistance to salt water, fresh water, crude oil, alkalis and weak acids. It is suitable for protective coating of splash zones, underwater areas and tank interiors. A film thickness of over 500 microns can be built in one application by airless spray.
TECHNICAL DATA
Type Epoxy/polyamide glass flake mastic paint
Recommened
Use
Splash zone and underwater area of ship's outer shell and offshore structures
Mixing Ratio : Color :
Base : Hardener = 79 : 21 [by volume]Grey, Red brown, Black
Flash Point : Base = 28.5℃, Hardener = 50℃ [degC] Solid by volume : 92 (+-2) [volume %] VOC : 153 [g/L] Coverage(Theoretical): 0.326 - 0.543 [L/m
2
]
Information
Film Thickness : WET 326 - 543 [micron]DRY 300 - 500 [micron]
() 5 oC 10 oC 20 oC 30 oC
Drying Time Surface Dry 14hrs. 6hrs. 4hrs.Hard Dry 32hrs. 16hrs. 12hrs.
Painting Interval Min 32hrs. 16hrs. 12hrs.Max 5days 3days 2days
Pot Life 4hrs. 2hrs. 1hr.
Method of Application : Airless spray, Brush Weather : Temperature : Minimum 10
degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 6.0[sec]
Tip No. : (GRACO)SILVERGUN(208-663) Paint Output Pressuer: 24.5~29.4[MPa] Spray Speed : 60~80[cm/sec]
Thinner : EPICON MARINE THINNER, Thinning: 0 - 3 % by Volume
Preceding Coats : BANNOH 500, BANNOH 2000
Conditionof
Application
Subsequent Coats : BANNOH 500 N, VINYL AC-HB, etc.
Packaging Two pack product
Notes 1.Waiting time before the first cargo loading Temp. 10degC 20degC 30degC (Days) 18 10 62.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
PERMAX No.3000MU(PM 3000MU)
Dec.2006
No. 6057
PERMAX No.3000MU, based on a combination of epoxy resin with glass-flake and polyamine resin, has excellent physical properties such as adhesion, toughness and abrasion resistance, etc., and chemical resistance to salt water, fresh water, crude oil, alkalis and weak acids. It is suitable for protective coating of splash zones, underwater areas and tank interiors.
TECHNICAL DATA
Type Epoxy/polyamine glass flake mastic paint
Recommened
Use
Splash zone and underwater area of ship's outer shell and offshore structures
Mixing Ratio : Color :
Base : Hardener = 82 : 18 [by volume]Light Grey, Red brown
Flash Point : Base = 32, Hardener = 24.5 [degC] Solid by volume : 80 (+-2) [volume %] VOC : 239 [g/L] Coverage(Theoretical): 0.25 - 0.375 [L/m
2
]
Information
Film Thickness : WET 250 - 375 [micron]DRY 200 - 300 [micron]
(D.F.T. 250micron) 5 oC 10 oC 20 oC 30 oC
Drying Time Surface Dry 5hrs. 4hrs.Hard Dry 15hrs. 12hrs.
Painting Interval Min 15hrs. 12hrs.Max 7days 5days
5hrs. 4hrs.
Method of Application : Airless spray; Brush Weather : Temperature : Minimum 20
degC, Humidity : Maximum 85 %R.H. For Airless Spray :
Tip No. : GRACO BallTip No205-723 Zincgun(208-663) Paint Output Pressuer: 14.7 - 19.7[MPa] Spray Speed : 60 - 80[cm/sec]
Thinner : EPICON MARINE THINNER, Thinning: 0 - 3 % by Volume
Preceding Coats : CERABOND
Conditionof
Application
Subsequent Coats : BANNOH 500, BANNOH 500 N, EPICON MARINE HB, etc.
Packaging Two pack product
Notes VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
PERMAX No.3000MU W(PM 3000MU W)
Dec.2006
No. 6059
PERMAX No.3000MU W, based on a combination of epoxy resin with glass-flake and polyamine resin, has excellent physical properties such as adhesion, toughness and abrasion resistance, etc., and chemical resistance to salt water, fresh water, crude oil, alkalis and weak acids. It is suitable for protective coating of splash zones, underwater areas and tank interiors.
TECHNICAL DATA
Type Epoxy/polyamine glass flake mastic paint
Recommened
Use
Splash zone and underwater area of ship's outer shell and offshore structures
Mixing Ratio : Color :
Base : Hardener = 82 : 18 [by volume]Light Grey, Red brown
Flash Point : Base = 32, Hardener = 26 [degC] Solid by volume : 80 (+-2) [volume %] VOC : 225 [g/L] Coverage(Theoretical): 0.25 - 0.375 [L/m
2
]
Information
Film Thickness : WET 250 - 375 [micron]DRY 200 - 300 [micron]
(D.F.T. 250micron) 5 oC 10 oC 20 oC 30 oC
Drying Time Surface Dry 10hrs. 8hrs. 3hrs.Hard Dry 28hrs. 20hrs. 10hrs.
Painting Interval Min 28hrs. 20hrs. 10hrs.Max 10days 7days 7days
Pot Life 4hrs. 3hrs. 2hrs.
Method of Application : Airless spray; Brush Weather : Temperature : Minimum 5
degC, Humidity : Maximum 85 %R.H. For Airless Spray :
Tip No. : (GRACO)BallTip No205-723 Zincgun(208-663) Paint Output Pressuer: 14.7 - 19.7[MPa] Spray Speed : 60 - 80[cm/sec]
Thinner : EPICON MARINE THINNER, Thinning: 0 - 3 % by Volume
Preceding Coats : CERABOND
Conditionof
Application
Subsequent Coats : BANNOH 500, BANNOH 500 N, EPICON MARINE HB, etc.
Packaging Two pack product
Notes VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
POLIBI T-1(PB T-1)
Feb.2006
No. 3040
POLIBI T-1 is a vinyl chloride resin based paint, providing excellent adhesion property, durability, weathering resistance and gloss retention. It is quick drying and easy to apply. Recommended as a finishing coat on the inside and outside of superstructures.
TECHNICAL DATA
Type Vinyl finish paint
Recommened
Use
Finish coat of vinyl system on the ship's inside and outside superstructures area and other steel structures.
Color : White Flash Point : 7.3 [degC] Solid by volume : 28 [volume %] VOC : 605 [g/L] Coverage(Theoretical): 0.072 - 0.108 [L/m
2
]
Information
Film Thickness : WET 72 - 108 [micron]DRY 20 - 30 [micron]
() 5 oC 10 oC 20 oC 30 oC
Drying Time Surface Dry 30mins. 25mins. 20mins. 15mins.Hard Dry 3hrs. 2.5hrs. 2hrs. 1.5hrs.
Painting Interval Min 5hrs. 4hrs. 3hrs. 2hrs.Max - - - -
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum 0
degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : (Fc#4)30 - 45[sec]
Tip No. : (GRACO)717,719 Paint Output Pressuer: 11.7 - 14.7[MPa] Spray Speed : 80 - 100[cm/sec]
Thinner : VINYL THINNER, Thinning: 6 - 12 % by Volume
Preceding Coats : VINYL RED LEAD PRIMER, VINYL RED LEAD PRIMER HB, VINYL AC
Conditionof
Application
Subsequent Coats : -
Packaging One pack product
Notes VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
RAVAX FINISH(RX FC)
Feb.2006
No. 4400
RAVAX FINISH, based on a chlorinated rubber vehicle, physically dries by evaporation of the solvents. It has excellent adhesion property, weathering resistance and gloss and colour retention. It is also highly resistant to the influence of salt water, oil and chalking. Although standard dry film thickness is 35 microns per coat, it is possible to obtain a maximum of 50 microns dry film thickness per coat.
TECHNICAL DATA
Type Chlorinated rubber finish paint
Recommened
Use
As a finishing coat on interior and exterior of superstructures
Color : White, As specified Flash Point : 25.5 [degC] Solid by volume : 42 (+-2) [volume %] VOC : 484 [g/L] Coverage(Theoretical): 0.072 - 0.12 [L/m
2
]
Information
Film Thickness : WET 72 - 120 [micron]DRY 30 - 50 [micron]
(D.F.T. 35micron) 5 oC 10 oC 20 oC 30 oC
Drying Time Surface Dry 1hr. 50mins. 30mins. 20mins.Hard Dry 6hrs. 5hrs. 4hrs. 3.5hrs.
Painting Interval Min 12hrs. 9hrs. 6hrs. 5hrs.Max - - - -
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum 0
degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : (Fc#4)100[sec]
Tip No. : (GRACO)719 Paint Output Pressuer: 11.7 - 14.7[MPa] Spray Speed : 80 - 100[cm/sec]
Thinner : RAVAX THINNER, Thinning: 0 - 5 % by Volume
Preceding Coats : RAVAX PRIMER, RAVAX RED LEAD PRIMER, etc.
Conditionof
Application
Subsequent Coats : -
Packaging One pack product
Notes VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
RAVAX PRIMER(RX P)
Feb.2006
No. 4100
RAVAX PRIMER is an effective anti-rust primer based on chlorinated rubber and drying by evaporation of the solvents. It has excellent rust-preventing and adhesion properties, weathering and oil resistance and other physical properties.
TECHNICAL DATA
Type Chlorinated rubber anti-rust primer
Recommened
Use
As an anti-rust primer on the superstructure of ships
Color : Red brown, White, Light gray Flash Point : 25.5 [degC] Solid by volume : 43 (+-2) [volume %] VOC : 495 [g/L] Coverage(Theoretical): 0.082 - 0.105 [L/m
2
]
Information
Film Thickness : WET 82 - 105 [micron]DRY 35 - 45 [micron]
(D.F.T. 40micron) 5 oC 10 oC 20 oC 30 oC
Drying Time Surface Dry 1hr. 50mins. 30mins. 20mins.Hard Dry 8hrs. 5hrs. 3hrs. 2hrs.
Painting Interval Min 10hrs. 8hrs. 5hrs. 4hrs.Max - - - -
Method of Application : Airless spray; Brush; Roller Weather : Temperature : Minimum 0
degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : (Fc#4)120[sec]
Tip No. : (GRACO)721,719 Paint Output Pressuer: 11.7 - 17.7[MPa] Spray Speed : 60 - 80[cm/sec]
Thinner : RAVAX THINNER, Thinning: 0 - 5 % by Volume
Preceding Coats : EVABOND, NZ PRIMER, WELBOND, CERABOND, EPICON ZINC RICH PRIMER,
Conditionof
Application
Subsequent Coats : RAVAX FINISH, RAVAX DECK, etc.
Packaging One pack product
Notes VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
RAVAX AC HB(RX AC HB)
Feb.2006
No. 4001
RAVAX AC HB is a chlorinated rubber paint giving a high-build quick drying, effective protection against corrosion. It affords good adhesion between the films as well as to shop primers and subsequent coats. It also possesses sea water resistance and shows good adhesion to subsequent coats even after prolonged weathering.
TECHNICAL DATA
Type Chlorinated rubber anti-corrosive paint, high-build
Recommened
Use
Steel ship's hull and other steel structures
Color : SR (Pink silver), S (Silver) Flash Point : 27.0 [degC] Solid by volume : 42 (+-2) [volume %] VOC : 489 [g/L] Coverage(Theoretical): 0.095 - 0.179 [L/m
2
]
Information
Film Thickness : WET 95 - 179 [micron]DRY 40 - 75 [micron]
() 5 oC 10 oC 20 oC 30 oC
Drying Time Surface Dry 1hr. 45mins. 30mins. 20mins.Hard Dry 6hrs. 4.5hrs. 3hrs. 2.5hrs.
Painting Interval Min 12hrs. 8hrs. 6hrs. 5hrs.Max - - - -
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum 0
degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : (Fc#4)140[sec]
Tip No. : (GRACO)721,723 Paint Output Pressuer: 14.7 - 17.7[MPa] Spray Speed : 60 - 80[cm/sec]
Thinner : RAVAX THINNER, Thinning: 0 - 5 % by Volume
Preceding Coats : NZ PRIMER, WELBOND, EPICON ZINC RICH PRIMER, CERABOND, etc.
Conditionof
Application
Subsequent Coats : RAVAX AF, RAVAX FINISH, TFA-10.20.30, etc.
Packaging One pack product
Notes VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
RAVAX AF(RX AF)
Mar.2006
No. 4010
RAVAX AF is a special synthetic resin based anti-fouling paint with a high content of antifoulant, providing extended effective protection against fouling, results in fuel saving and elimination of lost time due to reduction in speed resulting from fouling. It has excellent adhesion to RAVAX AC.
TECHNICAL DATA
Type Special synthetic resin anti-fouling paint
Recommened
Use
Anti-fouling finish of chlorinated rubber system on steel ship's bottom areas
Color : Dark red brown Flash Point : 24.3 [degC] Solid by volume : 50 (+-2) [volume %] VOC : 421 [g/L] Coverage(Theoretical): 0.07 - 0.09 [L/m
2
]
Information
Film Thickness : WET 70 - 90 [micron]DRY 35 - 45 [micron]
() 5 oC 10 oC 20 oC 30 oC
Drying Time Surface Dry 45mins. 30mins. 20mins. 15mins.Hard Dry 6hrs. 4.5hrs. 3hrs. 2hrs.
Painting Interval Min 15hrs. 9hrs. 5hrs. 4hrs.Max - - - -
Dry to Launch Min 16hrs. 10hrs. 6hrs. 5hrs.
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum 0
degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : (Fc#4)80[sec]
Tip No. : (GRACO)719,721 Paint Output Pressuer: 11.7 - 14.7[MPa] Spray Speed : 60 - 80[cm/sec]
Thinner : RAVAX THINNER, Thinning: 0 - 5 % by Volume
Preceding Coats : RAVAX AC, RAVAX AC HB, RAVAX AC S-HB, SILVAX SQ, etc.
Conditionof
Application
Subsequent Coats : -
Packaging One pack product
Notes 1.There is a risk of antifoulings becoming fouled when ships are stationary for three consecutive weeks or more,particularly in areas with a high risk of fouling.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
ROSWAN QD(RWN QD)
Feb.2006
No. 2130
ROSWAN QD, a white coloured alkyd resin based rust-preventing primer, has highly rust-preventing property. As it is white colour, it is especially recommended for use as a primer for white or light-colour finishes.
TECHNICAL DATA
Type Alkyd resin white primer.
Recommened
Use
As a rust-preventing primer for inside and outside of the superstructure and other steel structures
Color : White Flash Point : 43.0 [degC] Solid by volume : 51 (+-2) [volume %] VOC : 390 [g/L] Coverage(Theoretical): 0.059 - 0.078 [L/m
2
]
Information
Film Thickness : WET 59 - 78 [micron]DRY 30 - 40 [micron]
(D.F.T. 35micron) 5 oC 10 oC 20 oC 30 oC
Drying Time Surface Dry 4hrs. 2hrs. 1hr. 30mins.Hard Dry 18hrs. 12hrs. 6hrs. 3hrs.
Painting Interval Min 30hrs. 24hrs. 16hrs. 10hrs.Max 120days 100days 90days 60days
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum 0
degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : (Fc#4)110[sec]
Tip No. : (GRACO)719 Paint Output Pressuer: 10.7 - 13.8[MPa] Spray Speed : 80 - 110[cm/sec]
Thinner : MARINE THINNER, Thinning: 0 - 5 % by Volume
Preceding Coats : EVABOND, NZ PRIMER, LZI PRIMER, etc.
Conditionof
Application
Subsequent Coats : EVMARINE, Alkyd resin based paints
Packaging One pack product
Notes VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
ROSWAN QD HB(RWN QD HB)
Oct.2006
No. 2131
ROSWAN QD HB, a white colored alkyd resin based rust-preventing primer has highly effective rust-preventing property. Being white, it is especially recommended for use as a primer for white and light-colored finishes.
TECHNICAL DATA
Type Special alkyd resin primer, High-build
Recommened
Use
As a rust-preventing primer for inside of superstructure, deck, hold, and other steel structures
Color : White Flash Point : 36.0 [degC] Solid by volume : 51 (+-2) [volume %] VOC : 393 [g/L] Coverage(Theoretical): 0.059 - 0.137 [L/m
2
]
Information
Film Thickness : WET 59 - 137 [micron]DRY 30 - 70 [micron]
(D.F.T. 70micron) 5 oC 10 oC 20 oC 30 oC
Drying Time Surface Dry 6hrs. 3hrs. 1.5hrs. 45mins.Hard Dry 24hrs. 14hrs. 7hrs. 4hrs.
Painting Interval Min 48hrs. 30hrs. 20hrs. 16hrs.Max 120days 100days 90days 60days
Method of Application : Airless spray, Brush*, Roller Weather : Temperature : Minimum 0
degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 1 - 2Pa・s
Tip No. : (GRACO)719 Paint Output Pressuer: 14.7 - 17.7[MPa] Spray Speed : 70 - 90[cm/sec]
Thinner : MARINE THINNER, Thinning: 0 - 5 % by Volume
Preceding Coats : EVABOND, NZ PRIMER, LZI PRIMER, etc.
Conditionof
Application
Subsequent Coats : EVAMARINE, EVAMARINE HB, Alkyd resin based paints
Packaging One pack product
Notes 1.* Sufficient thickness is difficult to obtain by brush.2.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
ROSWAN QD ZR HB(RWN QD ZR HB)
Feb.2006
No. 2134
ROSWAN QD ZR HB, a white coloured alkari-resistant synthetic resin based rust-preventing primer has highly effective rust-preventing property. Being white, it is especially recommended for use as a primer for white and light-coloured finishes.
TECHNICAL DATA
Type Special synthetic resin primer,High-build
Recommened
Use
As the 1st coat of primer for inside of superstructure and other steel structures, when a conventional paint systen is specified on zinc shop primer.
Color : White Flash Point : 36.0 [degC] Solid by volume : 51 (+-2) [volume %] VOC : 393 [g/L] Coverage(Theoretical): 0.058 - 0.137 [L/m
2
]
Information
Film Thickness : WET 59 - 137 [micron]DRY 30 - 70 [micron]
() 5 oC 10 oC 20 oC 30 oC
Drying Time Surface Dry 6hrs. 3hrs. 1.5hrs. 45mins.Hard Dry 24hrs. 14hrs. 7hrs. 4hrs.
Painting Interval Min 48hrs. 30hrs. 20hrs. 16hrs.Max 120days 100days 90days 60days
Method of Application : Airless spray, Brush*, Roller Weather : Temperature : Minimum 0
degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 1 - 2Pa・s
Tip No. : (GRACO)719 Paint Output Pressuer: 14.7 - 17.7[MPa] Spray Speed : 70 - 90[cm/sec]
Thinner : MARINE THINNER, Thinning: 0 - 5 % by Volume
Preceding Coats : EVABOND, CERABOND, WELBOND, NZ PRIMER, etc.
Conditionof
Application
Subsequent Coats : EVAMARINE, EVAMARINE HB, Alkyd resin based paints
Packaging One pack product
Notes 1.* Sufficient thickness is difficult to obtain by brush.2.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
ROSWAN QD ZS HB(RWN QD ZS HB)
Feb.2006
No. 2136
ROSWAN QD ZS HB, a white coloured alkari-resistant synthetic resin based rust-preventing primer, has highly effective rust-preventing property. Being white colour, it is especially recommended for use as a primer for white and light-coloured finishes.
TECHNICAL DATA
Type Special synthetic resin primer
Recommened
Use
As the 1st coat of primer for inside of superstructure and other steel structures, when a conventional paint system is specified on zinc shop primer.
Color : White Flash Point : 31.0 [degC] Solid by volume : 44 (+-2) [volume %] VOC : 461 [g/L] Coverage(Theoretical): 0.067 - 0.157 [L/m
2
]
Information
Film Thickness : WET 67 - 157 [micron]DRY 30 - 70 [micron]
(D.F.T. 70micron) 5 oC 10 oC 20 oC 30 oC
Drying Time Surface Dry 6hrs. 3hrs. 1.5hrs. 45mins.Hard Dry 24hrs. 14hrs. 7hrs. 4hrs.
Painting Interval Min 48hrs. 30hrs. 20hrs. 16hrs.Max 120days 100days 90days 60days
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum 0
degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : (Fc#4)120[sec]
Tip No. : (GARCO)719 Paint Output Pressuer: 14.7 - 17.7[MPa] Spray Speed : 70 - 90[cm/sec]
Thinner : MARINE THINNER, Thinning: 0 - 5 % by Volume
Preceding Coats : EVABOND, EPICON ZINC RICH PRIMER B-2, CERABOND 2000, NZ PRIMER, etc.
Conditionof
Application
Subsequent Coats : EVAMARINE, ROSWAN QD*, ROSWAN QD HB, Alkyd resin based paints
Packaging One pack product
Notes 1.* In case of applying alkyd resin finish coat on ROSWAN QD ZS HB at outdoor exposed area or high humidity area , ROSWAN QD to be applied as a binder coat.2.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
RUST INHIBITIVE OIL "CK"()
Feb.2006
No. 8250
RUST INHIBITIVE OIL "CK", based on special petroleum resin and mineral spirit, is a temporary protective primer for fuel oil tanks.
TECHNICAL DATA
Type Petroleum resin
Recommened
Use
Color : Clear Flash Point : 42.5 [degC] Solid by volume : 49 [volume %] VOC : 386 [g/L] Coverage(Theoretical): 0.043 [L/m
2
]
Information
Film Thickness : WET 41 [micron]DRY 20 [micron]
() 5 oC 10 oC 20 oC 30 oC
Drying Time Surface Dry 1hr. 30mins. 15mins. 5mins.Hard Dry 4hrs. 2hrs. 1hr. 30mins.
Painting Interval Min - - - -Max - - - -
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum 0
degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : (Fc#4)90[sec]
Tip No. : (GRACO)615,717 Paint Output Pressuer: 10.7 - 13.8[MPa]
Spray Speed : 60 - 80[cm/sec] Thinner : MARINE THINNER,
Thinning: - % by Volume Preceding Coats : -
Conditionof
Application
Subsequent Coats : -
Packaging One pack product
Notes 1.The ingredients of this product will be dissolved by the fuel oil but they do not affect the quality of the fuel oil at all.2.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
RUST INHIBITIVE PRIMER Z(RI Z)
Sep.2006
No. 2110
RUST INHIBITIVE PRIMER Z is an alkyd based primer. It is a highly effective rust-preventing primer which possesses excellent adhesion properties and flexibility.
TECHNICAL DATA
Type Alkyd resin primer
Recommened
Use
As a rust-preventing primer on inside and outside of superstructures, deck, hold, and other steel structures
Color : Red brown Flash Point : 43.0 [degC] Solid by volume : 52 (+-2) [volume %] VOC : 383 [g/L] Coverage(Theoretical): 0.058 - 0.077 [L/m
2
]
Information
Film Thickness : WET 58 - 77 [micron]DRY 30 - 40 [micron]
() 5 oC 10 oC 20 oC 30 oC
Drying Time Surface Dry 4hrs. 2hrs. 1hr. 30mins.Hard Dry 18hrs. 12hrs. 6hrs. 3hrs.
Painting Interval Min 30hrs. 20hrs. 16hrs. 10hrs.Max 120days 100days 90days 60days
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum 0
degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : (Fc#4)120[sec]
Tip No. : (GRACO)719 Paint Output Pressuer: 10.7 - 13.8[MPa] Spray Speed : 80 - 100[cm/sec]
Thinner : MARINE THINNER, Thinning: 0 - 5 % by Volume
Preceding Coats : EVABOND, NZ PRIMER, etc.
Conditionof
Application
Subsequent Coats : EVAMARINE, Alkyd resin based paints
Packaging One pack product
Notes VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
SEA FRONTIER(SFT)
Mar.2006
No. 5917N
SEA FRONTIER , a tin free self polishing antifouling paint based on the specific polymer without cuprous oxide, is designed for the coastal ships sailing in the heavy fouled area . Excellent antifouling effect is derived from the highly active hydrolysis polymer which ensures maximum effectiveness and leaching of the biocides. Activation at the surface is maintained by control of hydrolysis thus providing long term antifouling protection commensurate with the applied film thickness.
TECHNICAL DATA
Type Tin free self polishing antifouling without cuprous oxide
Recommened
Use
On the ship bottom for coastal steel ships and aluminum boats
Color : Red, Light red, Pink, Blue Flash Point : 25.0 [degC] Solid by volume : 41 (+-2) [volume %] VOC : 528 [g/L] Coverage(Theoretical): 0.18 - 0.37 [L/m
2
]
Information
Film Thickness : WET 183 - 366 [micron]DRY 75 - 150 [micron]
() 5 oC 10 oC 20 oC 30 oC
Drying Time Surface Dry 3hrs. 2hrs. 1hr. 30mins.Hard Dry 12hrs. 8hrs. 5hrs. 4hrs.
Painting Interval Min 12hrs. 8hrs. 5hrs. 4hrs.Max - - - -
Dry to Launch Min 24hrs. 18hrs. 12hrs. 10hrs.
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum 0
degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 1.5 - 2.5Pa・s
Tip No. : (GRACO)621 - 723 Paint Output Pressuer: 11.7 - 14.7[MPa] Spray Speed : 60 - 80[cm/sec]
Thinner : RAVAX THINNER, Thinning: 0 - 5 % by Volume
Preceding Coats : SILVAX SQ-K, VINYL AC-HB, HIPER AC, RAVAX AC-HB, BANNOH 500 N, BANNOH 500 R,
Conditionof
Application
Subsequent Coats : -
Packaging One pack product
Notes 1.There is a risk of antifoulings becoming fouled when ships are stationary for three consecutive weeks or more,particularly in areas with a high risk of fouling.2.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
SEA FRONTIER F(SFT F)
Mar.2006
No. 5922N
SEA FRONTIER F , a tin free self polishing antifouling paint based on the specific polymer without cuprous oxide, is designed for the coastal ships sailing in the heavy fouled area . Excellent antifouling effect is derived from the highly active hydrolysis polymer which ensures maximum effectiveness and leaching of the biocides. Activation at the surface is maintained by control of hydrolysis thus providing long term antifouling protection commensurate with the applied film thickness.
TECHNICAL DATA
Type Tin free self polishing antifouling without cuprous oxide
Recommened
Use
On the ship bottom for coastal steel ships and aluminum boats
Color : Red, Light red Flash Point : 25.0 [degC] Solid by volume : 40 (+-2) [volume %] VOC : 522 [g/L] Coverage(Theoretical): 0.187 - 0.371 [L/m
2
]
Information
Film Thickness : WET 373 [micron]DRY 150 [micron]
() 5 oC 10 oC 20 oC 30 oC
Drying Time Surface Dry 3hrs. 2hrs. 1hr. 30mins.Hard Dry 12hrs. 8hrs. 5hrs. 4hrs.
Painting Interval Min 12hrs. 8hrs. 5hrs. 4hrs.Max - - - -
Dry to Launch Min 24hrs. 18hrs. 12hrs. 10hrs.
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum 0
degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 1.5 - 2.5Pa・s
Tip No. : (GRACO)621 - 723 Paint Output Pressuer: 11.7 - 14.7[MPa] Spray Speed : 60 - 80[cm/sec]
Thinner : RAVAX THINNER, Thinning: 0 - 5 % by Volume
Preceding Coats : SILVAX SQ-K, VINYL AC-HB, HIPER AC, RAVAX AC-HB, BANNOH 500 N, BANNOH 500 R,
Conditionof
Application
Subsequent Coats : -
Packaging One pack product
Notes 1.There is a risk of antifoulings becoming fouled when ships are stationary for three consecutive weeks or more,particularly in areas with a high risk of fouling.2.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
SEA FRONTIER H(SFT H)
Mar.2006
No. 5919N
SEA FRONTIER H , a tin free self polishing antifouling paint based on the specific polymer without cuprous oxide, is designed for the coastal ships sailing in the heavy fouled area . Excellent antifouling effect is derived from the highly active hydrolysis polymer which ensures maximum effectiveness and leaching of the biocides. Activation at the surface is maintained by control of hydrolysis thus providing long term antifouling protection commensurate with the applied film thickness.
TECHNICAL DATA
Type Tin free self polishing antifouling without cuprous oxide
Recommened
Use
On the ship bottom for coastal steel ships and aluminum boats
Color : Red, Pink, Blue, Black Flash Point : 25.0 [degC] Solid by volume : 41 (+-2) [volume %] VOC : 518 [g/L] Coverage(Theoretical): 0.18 - 0.37 [L/m
2
]
Information
Film Thickness : WET 183 - 366 [micron]DRY 75 - 150 [micron]
(D.F.T. 100micron) 5 oC 10 oC 20 oC 30 oC
Drying Time Surface Dry 3hrs. 2hrs. 1hr. 30mins.Hard Dry 12hrs. 8hrs. 5hrs. 4hrs.
Painting Interval Min 12hrs. 8hrs. 5hrs. 4hrs.Max - - - -
Dry to Launch Min 24hrs. 18hrs. 12hrs. 10hrs.
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum 0
degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 1.5 - 2.5Pa・s
Tip No. : (GRACO)621 - 723 Paint Output Pressuer: 11.7 - 14.7[MPa] Spray Speed : 60 - 80[cm/sec]
Thinner : RAVAX THINNER, Thinning: 0 - 5 % by Volume
Preceding Coats : SILVAX SQ-K, VINYL AC-HB, HIPER AC, RAVAX AC-HB, BANNOH 500 N, BANNOH 500 R,
Conditionof
Application
Subsequent Coats : -
Packaging One pack product
Notes 1.There is a risk of antifoulings becoming fouled when ships are stationary for three consecutive weeks or more,particularly in areas with a high risk of fouling.2.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
SEA FRONTIER S(SFT S)
Mar.2006
No. 5921N
SEA FRONTIER S, a tin free self polishing antifouling paint based on the specific polymer without cuprous oxide, is designed for the coastal ships sailing in the heavy fouled area . Excellent antifouling effect is derived from the highly active hydrolysis polymer which ensures maximum effectiveness and leaching of the biocides. Activation at the surface is maintained by control of hydrolysis thus providing long term antifouling protection commensurate with the applied film thickness.
TECHNICAL DATA
Type Tin free self polishing antifouling without cuprous oxide
Recommened
Use
On the ship bottom for coastal steel ships and aluminum boats
Color : Red, Light red, Pink, Black Flash Point : 25.0 [degC] Solid by volume : 41 (+-2) [volume %] VOC : 528 [g/L] Coverage(Theoretical): 0.18 - 0.37 [L/m
2
]
Information
Film Thickness : WET 183 - 366 [micron]DRY 75 - 150 [micron]
(D.F.T. 100micron) 5 oC 10 oC 20 oC 30 oC
Drying Time Surface Dry 3hrs. 2hrs. 1hr. 30mins.Hard Dry 12hrs. 8hrs. 5hrs. 4hrs.
Painting Interval Min 12hrs. 8hrs. 5hrs. 4hrs.Max - - - -
Dry to Launch Min 24hrs. 18hrs. 12hrs. 10hrs.
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum 0
degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 1.5 - 2.5Pa・s
Tip No. : (GRACO)621 - 723 Paint Output Pressuer: 11.7 - 14.7[MPa] Spray Speed : 60 - 80[cm/sec]
Thinner : RAVAX THINNER, Thinning: 0 - 5 % by Volume
Preceding Coats : SILVAX SQ-K, VINYL AC-HB, HIPER AC, RAVAX AC-HB, BANNOH 500 N, BANNOH 500 R,
Conditionof
Application
Subsequent Coats : -
Packaging One pack product
Notes 1.There is a risk of antifoulings becoming fouled when ships are stationary for three consecutive weeks or more,particularly in areas with a high risk of fouling.2.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
SEA FRONTIER ME(SFT ME)
Mar.2006
No. 5917M
SEA FRONTIER ME , a tin free self polishing antifouling paint based on the specific polymer without cuprous oxide, is designed for the coastal ships sailing in the heavy fouled area . Excellent antifouling effect is derived from the highly active hydrolysis polymer which ensures maximum effectiveness and leaching of the biocides. Activation at the surface is maintained by control of hydrolysis thus providing long term antifouling protection commensurate with the applied film thickness.
TECHNICAL DATA
Type Tin free self polishing antifouling without cuprous oxide
Recommened
Use
On the ship bottom for coastal steel ships and aluminum boats
Color : Red, Light red Flash Point : 24.5 [degC] Solid by volume : 45 (+-2) [volume %] VOC : 474 [g/L] Coverage(Theoretical): 0.11 - 0.33 [L/m
2
]
Information
Film Thickness : WET 111 - 333 [micron]DRY 50 - 150 [micron]
() 5 oC 10 oC 20 oC 30 oC
Drying Time Surface Dry 3hrs. 2hrs. 1hr. 30mins.Hard Dry 12hrs. 8hrs. 5hrs. 4hrs.
Painting Interval Min 12hrs. 8hrs. 5hrs. 4hrs.Max - - - -
Dry to Launch Min 24hrs. 18hrs. 12hrs. 10hrs.
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum 0
degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 1.5 - 2.5Pa・s
Tip No. : (GRACO)621 - 723 Paint Output Pressuer: 11.7 - 14.7[MPa] Spray Speed : 60 - 80[cm/sec]
Thinner : RAVAX THINNER, Thinning: 0 - 5 % by Volume
Preceding Coats : SILVAX SQ-K, VINYL AC-HB, HIPER AC, RAVAX AC-HB, BANNOH 500 N, BANNOH 500 R,
Conditionof
Application
Subsequent Coats : -
Packaging One pack product
Notes 1.There is a risk of antifoulings becoming fouled when ships are stationary for three consecutive weeks or more,particularly in areas with a high risk of fouling.2.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
SEA GRANDPRIX 1000(SGP 1000)
Mar.2006
No. 5909
SEA GRANDPRIX 1000 is a tin free self polishing antifouling paint based on the specific polymer with highly hydrolysis activity. Excellent antifouling effect is derived from the highly active polymer which ensures maximum effectiveness and leaching of the biocides. Activation at the surface is maintained by control of hydrolysis thus providing long term antifouling protection commensurate with applied film thickness.
TECHNICAL DATA
Type Tin free self polishing antifouling paint
Recommened
Use
Antifouling paint on steel ship's bottom for world wide service with extended dry-docking interval.
Color : Red, Dark red, Light red, Purple Flash Point : 23.2 [degC] Solid by volume : 44 (+-2) [volume %] VOC : 504 [g/L] Coverage(Theoretical): 0.17 - 0.34 [L/m
2
]
Information
Film Thickness : WET 170 - 340 [micron]DRY 75 - 150 [micron]
() 5 oC 10 oC 20 oC 30 oC
Drying Time Surface Dry 3hrs. 2hrs. 1hr. 30mins.Hard Dry 12hrs. 8hrs. 5hrs. 4hrs.
Painting Interval Min 12hrs. 8hrs. 5hrs. 4hrs.Max - - - -
Dry to Launch Min 24hrs. 18hrs. 12hrs. 10hrs.
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum -5
degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 1.5 - 2.5Pa・s
Tip No. : (GRACO)621 - 723 Paint Output Pressuer: 11.7 - 14.7[MPa] Spray Speed : 60 - 80[cm/sec]
Thinner : RAVAX THINNER, Thinning: 0 - 5 % by Volume
Preceding Coats : SILVAX SQ-K, VINYL AC-HB, HIPER AC, RAVAX AC-HB, BANNOH 500 N, BANNOH 500 R,
Conditionof
Application
Subsequent Coats : -
Packaging One pack product
Notes 1.There is a risk of antifoulings becoming fouled when ships are stationary for three consecutive weeks or more,particularly in areas with a high risk of fouling.2.Below 10 degC, extra solvent maybe required to obtain application viscosity.3.But too much solvent results in reduced sag resistance and paint film property.4.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
SEA GRANDPRIX 2000(SGP 2000)
Mar.2006
No. 5911
SEA GRANDPRIX 2000 is a tin free self polishing antifouling paint based on the specific polymer with highly hydrolysis activity. Excellent antifouling effect is derived from the highly active polymer which ensures maximum effectiveness and leaching of the biocides. Activation at the surface is maintained by control of hydrolysis thus providing long term antifouling protection commensurate with applied film thickness.
TECHNICAL DATA
Type Tin free self polishing antifouling paint
Recommened
Use
Antifouling paint on steel ship's bottom for world wide service with extended dry-docking interval.
Color : Red, Light red, Brown, Purple Flash Point : 23.2 [degC] Solid by volume : 44 (+-2) [volume %] VOC : 494 [g/L] Coverage(Theoretical): 0.17 - 0.34 [L/m
2
]
Information
Film Thickness : WET 170 - 340 [micron]DRY 75 - 150 [micron]
() 5 oC 10 oC 20 oC 30 oC
Drying Time Surface Dry 3hrs. 2hrs. 1hr. 30mins.Hard Dry 12hrs. 8hrs. 5hrs. 4hrs.
Painting Interval Min 12hrs. 8hrs. 5hrs. 4hrs.Max - - - -
Dry to Launch Min 24hrs. 18hrs. 12hrs. 10hrs.
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum 0
degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 1.5 - 2.5Pa・s
Tip No. : (GRACO)621 - 723 Paint Output Pressuer: 11.7 - 14.7[MPa] Spray Speed : 60 - 80[cm/sec]
Thinner : RAVAX THINNER, Thinning: 0 - 5 % by Volume
Preceding Coats : SILVAX SQ-K, VINYL AC-HB, HIPER AC, RAVAX AC-HB, BANNOH 500 AC,
Conditionof
Application
Subsequent Coats : -
Packaging One pack product
Notes 1.There is a risk of antifoulings becoming fouled when ships are stationary for three consecutive weeks or more,particularly in areas with a high risk of fouling.2.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
SEA GRANDPRIX 300(SGP 300)
Mar.2006
No. 5901
SEA GRANDPRIX 300,is used for fouling control on the flat bottom, is a tin free self polishing antifouling paint based on the specific polymer with highly hydrolysis activity. Excellent antifouling effect is derived from the highly active polymer which ensures maximum effectiveness and leaching of the biocides. Activation at the surface is maintained by control of hydrolysis thus providing long term antifouling protection commensurate with applied film thickness.
TECHNICAL DATA
Type Tin free self polishing antifouling paint
Recommened
Use
Antifouling paint on steel ship's flat bottom for world wide service with extended dry-docking interval.
Color : Red, Light red, Purple Flash Point : 25.0 [degC] Solid by volume : 47 (+-2) [volume %] VOC : 484 [g/L] Coverage(Theoretical): 0.16 - 0.32 [L/m
2
]
Information
Film Thickness : WET 160 - 319 [micron]DRY 75 - 150 [micron]
() 5 oC 10 oC 20 oC 30 oC
Drying Time Surface Dry 3hrs. 2hrs. 1hr. 30mins.Hard Dry 12hrs. 8hrs. 5hrs. 4hrs.
Painting Interval Min 12hrs. 8hrs. 5hrs. 4hrs.Max - - - -
Dry to Launch Min 24hrs. 18hrs. 12hrs. 10hrs.
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum 0
degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 1.5 - 2.5Pa・s
Tip No. : (GRACO)621 - 723 Paint Output Pressuer: 11.7 - 14.7[MPa] Spray Speed : 60 - 80[cm/sec]
Thinner : RAVAX THINNER, Thinning: 0 - 5 % by Volume
Preceding Coats : SILVAX SQ-K, HIPER AC, RAVAX AC HB, BANNOH 500 N, BANNOH 500 R,
Conditionof
Application
Subsequent Coats : -
Packaging One pack product
Notes 1.There is a risk of antifoulings becoming fouled when ships are stationary for three consecutive weeks or more,particularly in areas with a high risk of fouling.2.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
SEA GRANDPRIX 330(SGP 330)
Mar.2007
No. 5902
SEA GRANDPRIX 330 is a tin free antifouling paint with self polishing action in service and long protection against marine organisms. The specific vehicle composition provides a unique fusion technology during operation , resulting in long lasting antifouling performance.
TECHNICAL DATA
Type Tin free self polishing antifouling paint
Recommened
Use
Antifouling paint on steel ship's bottom for world wide service with extended dry-docking interval.
Color : Brown, Light brown Flash Point : 26.0 [degC] Solid by volume : 62 (+-2) [volume %] VOC : 371 [g/L] Coverage(Theoretical): 0.12 - 0.24 [L/m
2
]
Information
Film Thickness : WET 121 - 242 [micron]DRY 75 - 150 [micron]
(D.F.T. 100micron) 5 oC 10 oC 20 oC 30 oC
Drying Time Surface Dry 3hrs. 2hrs. 1hr. 30mins.Hard Dry 12hrs. 8hrs. 5hrs. 4hrs.
Painting Interval Min 12hrs. 8hrs. 5hrs. 4hrs.Max - - - -
Dry to Launch Min 24hrs. 18hrs. 12hrs. 10hrs.
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum 0
degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : (Fc#4)90[sec]
Tip No. : (GRACO)621(721) - 635(735) Paint Output Pressuer: 11.7 - 14.7[MPa] Spray Speed : 60 - 80[cm/sec]
Thinner : RAVAX THINNER, Thinning: 0 - 5 % by Volume
Preceding Coats : SILVAX SQ-M, VINYL AC-HB, RAVAX AC HB, RAVAX AC-P, HIPER AC
Conditionof
Application
Subsequent Coats : -
Packaging One pack product
Notes 1.There is a risk of antifoulings becoming fouled when ships are stationary for three consecutive weeks or more,particularly in areas with a high risk of fouling.2.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
SEA GRANDPRIX 500(SGP 500)
Mar.2006
No. 5905
SEA GRANDPRIX 500 is a tin free self polishing antifouling paint based on the specific polymer with highly hydrolysis activity. Excellent antifouling effect is derived from the highly active polymer which ensures maximum effectiveness and leaching of the biocides. Activation at the surface is maintained by control of hydrolysis thus providing long term antifouling protection commensurate with applied film thickness.
TECHNICAL DATA
Type Tin free self polishing antifouling paint
Recommened
Use
Antifouling paint on steel ship's bottom for world wide service with extended dry-docking interval.
Color : Red, Light red, Purple Flash Point : 25.0 [degC] Solid by volume : 46 (+-2) [volume %] VOC : 481 [g/L] Coverage(Theoretical): 0.16 - 0.33 [L/m
2
]
Information
Film Thickness : WET 163 - 326 [micron]DRY 75 - 150 [micron]
() 5 oC 10 oC 20 oC 30 oC
Drying Time Surface Dry 3hrs. 2hrs. 1hr. 30mins.Hard Dry 12hrs. 8hrs. 5hrs. 4hrs.
Painting Interval Min 12hrs. 8hrs. 5hrs. 4hrs.Max - - - -
Dry to Launch Min 24hrs. 18hrs. 12hrs. 10hrs.
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum -5
degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 1.5 - 2.5Pa・s
Tip No. : (GARCO)621 - 723 Paint Output Pressuer: 11.7 - 14.7[MPa] Spray Speed : 60 - 80[cm/sec]
Thinner : RAVAX THINNER, Thinning: 0 - 5 % by Volume
Preceding Coats : SILVAX SQ-K, VINYL AC-HB, HIPER AC, RAVAX AC-HB, BANNOH 500 N, BANNOH 500 R,
Conditionof
Application
Subsequent Coats : -
Packaging One pack product
Notes 1.There is a risk of antifoulings becoming fouled when ships are stationary for three consecutive weeks or more,particularly in areas with a high risk of fouling.2.Below 10 degC, extra solvent maybe required to obtain application viscosity.3.But too much solvent results in reduced sag resistance and paint film property.4.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
SEA GRANDPRIX 500 M(SGP 500 M)
Mar.2006
No. 5905M
SEA GRANDPRIX 500 M is a tin free self polishing antifouling paint based on the specific polymer with highly hydrolysis activity. Excellent antifouling effect is derived from the highly active polymer which ensures maximum effectiveness and leaching of the biocides. Activation at the surface is maintained by control of hydrolysis thus providing long term antifouling protection commensurate with applied film thickness.
TECHNICAL DATA
Type Tin free self polishing antifouling paint
Recommened
Use
Antifouling paint on steel ship's bottom for world wide service with extended dry-docking interval.
Color : Red, Light red, Purple Flash Point : 25.0 [degC] Solid by volume : 46 (+-2) [volume %] VOC : 495 [g/L] Coverage(Theoretical): 0.16 - 0.33 [L/m
2
]
Information
Film Thickness : WET 163 - 326 [micron]DRY 75 - 150 [micron]
() 5 oC 10 oC 20 oC 30 oC
Drying Time Surface Dry 3hrs. 2hrs. 1hr. 30mins.Hard Dry 12hrs. 8hrs. 5hrs. 4hrs.
Painting Interval Min 12hrs. 8hrs. 5hrs. 4hrs.Max - - - -
Dry to Launch Min 24hrs. 18hrs. 12hrs. 10hrs.
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum 0
degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 1.5 - 2.5Pa・s
Tip No. : (GRACO)621 - 723 Paint Output Pressuer: 11.7 - 14.7[MPa] Spray Speed : 60 - 80[cm/sec]
Thinner : RAVAX THINNER, Thinning: 0 - 5 % by Volume
Preceding Coats : SILVAX SQ-K, VINYL AC-HB, HIPER AC, RAVAX AC-HB, BANNOH 500 N, BANNOH 500 R,
Conditionof
Application
Subsequent Coats : -
Packaging One pack product
Notes 1.There is a risk of antifoulings becoming fouled when ships are stationary for three consecutive weeks or more,particularly in areas with a high risk of fouling.2.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
SEA GRANDPRIX 800(SGP 800)
Mar.2006
No. 5912
SEA GRANDPRIX 800 is a tin free self polishing antifouling paint based on the specific polymer with hydrolysis activity. Excellent antifouling effect is derived from the active polymer which ensures maximum effectiveness and leaching of the biocides. Activation at the surface is maintained by control of hydrolysis thus providing long term antifouling protection commensurate with applied film thickness.
TECHNICAL DATA
Type Tin free self polishing antifouling paint
Recommened
Use
Antifouling paint on steel ship's bottom for coastal ships.
Color : Red, Light red Flash Point : 23.2 [degC] Solid by volume : 44 (+-2) [volume %] VOC : 513 [g/L] Coverage(Theoretical): 0.11 - 0.34 [L/m
2
]
Information
Film Thickness : WET 113 - 340 [micron]DRY 50 - 150 [micron]
(D.F.T. 100micron) 5 oC 10 oC 20 oC 30 oC
Drying Time Surface Dry 3hrs. 2hrs. 1hr. 30mins.Hard Dry 12hrs. 8hrs. 5hrs. 4hrs.
Painting Interval Min 12hrs. 8hrs. 5hrs. 4hrs.Max - - - -
Dry to Launch Min 24hrs. 18hrs. 12hrs. 10hrs.
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum 0
degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 1.5 - 2.5Pa・s
Tip No. : (GRACO)621 - 723 Paint Output Pressuer: 11.7 - 14.7[MPa] Spray Speed : 60 - 80[cm/sec]
Thinner : RAVAX THINNER, Thinning: 0 - 5 % by Volume
Preceding Coats : SILVAX SQ-K, VINYL AC-HB, HIPER AC, RAVAX AC-HB, BANNOH 500 R,
Conditionof
Application
Subsequent Coats : -
Packaging One pack product
Notes 1.There is a risk of antifoulings becoming fouled when ships are stationary for three consecutive weeks or more,particularly in areas with a high risk of fouling.2.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
SEA GRANDPRIX CF MK II(SGP CF MK II)
Dec.2006
No. 5830
SEA GRANDPRIX CF MK II is a tin and copper free self polishing anti-fouling paint based on a unique hydrolysis polymer. In service, SEA GRANDPRIX CF MK II's unique polymer presents a very thin hydrolysed active layer on the paint film surface ensuring an efficient and controlled biocide release mechanism.In our view this is the most efficient biocide release mechanism currently available . This efficient biocide release mechanism also ensures an extremely low hull surface roughness. The absence of tin, copper and other heavy metals in SEA GRANDPRIX CF MK II means that it remains colour-fastwithout fading or staining for the duration of the service life . IMO Anti-fouling System Convention compliant (AFS/CONF/26)
TECHNICAL DATA
Type Tin and copper free self polishing antifouling
Recommened
Use
Antifouling paint on steel ship's bottom for world wide service with extended dry-docking interval
Color : Red, Light red, Purple Flash Point : 25.0 [degC] Solid by volume : 50 ±2 [volume %] VOC : 437 [g/L] Coverage(Theoretical): 0.15 - 0.32 [L/m
2
]
Information
Film Thickness : WET 150 - 320 [micron]DRY 75 - 160 [micron]
() 5 oC 10 oC 20 oC 30 oC
Drying Time Surface Dry 3hrs. 2hrs. 1hr. 30min.Hard Dry 12hrs. 8hrs. 5hrs. 4hrs.
Painting Interval Min 12hrs. 8hrs. 5hrs. 4hrs.Max - - - -
Dry to Launch Min 24hrs. 18hrs. 12hrs. 10hrs.
Method of Application : Airless spray; Brush; Roller Weather : Temperature : Minimum -5
degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 1.5 - 2.5Pa・s
Tip No. : (GRACO)621 - 723 Paint Output Pressuer: 11.7 - 14.7[MPa] Spray Speed : 60 - 80[cm/sec]
Thinner : RAVAX THINNER, Thinning: 0 - 5 % by Volume
Preceding Coats : BANNOH 500 N, BANNOH 500 R, SILVAX SQ-K, HIPER AC, RAVAX AC-HB,
Conditionof
Application
Subsequent Coats : -
Packaging One pack product
Notes 1.The information contained in this technical data sheets in based on laboratory testing and practical in service experience. Note 1: Please refer to the above painting intervals and dry to launch times, for below 320μ total DFT.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
Note 2: When applying over 320μ total DFT, or applying 3 coats or more, CMP recommendthat 1 (one) day interval between the application of A/F and A/F and 24 hours minimum dry to launch. Note 3: In case of application below 5°C.2.(below 0degC) Surface Hard Interval Interval dry to Launch Dry Dry Min Max Min 0degC 4hrs 16hr 16hr - 36hr -5degC 6hrs 22hr 22hr - 48hr
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
SEA GRANDPRIX CF MK II L(SGP CF MK II L)
Dec.2006
No. 5831
SEA GRANDPRIX CF MK II L is a tin and copper free self polishing anti-fouling paint based on a unique hydrolysis polymer. In service, SEA GRANDPRIX CF MK II L's unique polymer presents a very thin hydrolysed active layer on the paint film surface ensuring an efficient and controlled biocide release mechanism.In our view this is the most efficient biocide release mechanism currently available . This efficient biocide release mechanism also ensures an extremely low hull surface roughness. The absence of tin, copper and other heavy metals in SEA GRANDPRIX CF MK II L means that it remains colour-fastwithout fading or staining for the duration of the service life .
TECHNICAL DATA
Type Tin and copper free self polishing antifouling
Recommened
Use
Antifouling paint on steel ship's bottom for world wide service with extended dry-docking interval
Color : Red, Light red, Purple Flash Point : 24.5 [degC] Solid by volume : 50 ±2 [volume %] VOC : 435 [g/L] Coverage(Theoretical): 0.15 - 0.32 [L/m
2
]
Information
Film Thickness : WET 150 - 320 [micron]DRY 75 - 160 [micron]
() 5 oC 10 oC 20 oC 30 oC
Drying Time Surface Dry 3hrs. 2hrs. 1hr. 30mins.Hard Dry 12hrs. 8hrs. 5hrs. 4hrs.
Painting Interval Min 12hrs. 8hrs. 5hrs. 4hrs.Max - - - -
Dry to Launch Min 24hrs. 18hrs. 12hrs. 10hrs.
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum -5
degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 1.5 - 2.5Pa・s
Tip No. : (GRACO)621 - 723 Paint Output Pressuer: 11.7 - 14.7[MPa] Spray Speed : 60 - 80[cm/sec]
Thinner : RAVAX THINNER, Thinning: 0 - 5 % by Volume
Preceding Coats : BANNOH 500 N, BANNOH 500 R, SILVAX SQ-K, HIPER AC, RAVAX AC-HB,
Conditionof
Application
Subsequent Coats : -
Packaging One pack product
Notes 1.The information contained in this technical data sheets in based on laboratory testing and practical in service experience. Note 1: Please refer to the above painting intervals and dry to launch times, for below 320μ total DFT. Note 2: When applying over 320μ total DFT, or applying 3 coats or more, CMP recommend
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
that 1 (one) day interval between the application of A/F and A/F and 24 hours minimum dry tolaunch. Note 3: In case of application below 5°C.2.(below 0degC) Surface Hard Interval Interval dry to Launch Dry Dry Min Max Min 0degC 4hrs 16hr 16hr - 36hr -5degC 6hrs 22hr 22hr - 48hr
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
SEA GRANDPRIX CF SUPER(SGP CF SP)
Mar.2006
No. 5921
SEA GRANDPRIX CF SUPER, a tin free self polishing antifouling paint based on the specific polymer without cuprous oxide, is designed for the coastal ships sailing in the heavy fouled area . Excellent antifouling effect is derived from the highly active hydrolysis polymer which ensures maximum effectiveness and leaching of the biocides. Activation at the surface is maintained by control of hydrolysis thus providing long term antifouling protection commensurate with the applied film thickness.
TECHNICAL DATA
Type Tin free self polishing antifouling without cuprous oxide
Recommened
Use
On the ship bottom for coastal steel ships and aluminum boats
Color : Red, Light red, Pink Flash Point : 25.0 [degC] Solid by volume : 44 (+-2) [volume %] VOC : 488 [g/L] Coverage(Theoretical): 0.17 - 0.341 [L/m
2
]
Information
Film Thickness : WET 170 - 341 [micron]DRY 75 - 150 [micron]
(D.F.T. 100micron) 5 oC 10 oC 20 oC 30 oC
Drying Time Surface Dry 3hrs. 2hrs. 1hr. 30mins.Hard Dry 12hrs. 8hrs. 5hrs. 4hrs.
Painting Interval Min 12hrs. 8hrs. 5hrs. 4hrs.Max - - - -
Dry to Launch Min 24hrs. 18hrs. 12hrs. 10hrs.
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum 0
degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 1.5 - 2.5Pa・s
Tip No. : (GRACO)621 - 723 Paint Output Pressuer: 11.7 - 14.7[MPa] Spray Speed : 60 - 80[cm/sec]
Thinner : RAVAX THINNER, Thinning: 0 - 5 % by Volume
Preceding Coats : SILVAX SQ-K, VINYL AC-HB, HIPER AC, RAVAX AC-HB, etc.
Conditionof
Application
Subsequent Coats : -
Packaging One pack product
Notes 1.There is a risk of antifoulings becoming fouled when ships are stationary for three consecutive weeks or more,particularly in areas with a high risk of fouling.2.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
SEA GRANDPRIX CF SUPER NFD(SGP CF SP NFD)
Nov.2006
No. 5917P
SEA GRANDPRIX CF SUPER NFD, a tin free self polishing antifouling paint based on the specific polymer without cuprous oxide, is designed for an None Final Dock system of new buildings in the heavy fouled area . Activation at the surface is maintained by control of hydrolysis thus providing long term antifouling protection commensurate with the applied film thickness.
TECHNICAL DATA
Type Tin free self polishing antifouling without cuprous oxide
Recommened
Use
On the ship bottom for coastal steel ships and aluminum boats
Color : Red Flash Point : 25.0 [degC] Solid by volume : 42 ±2 [volume %] VOC : 509 [g/L] Coverage(Theoretical): 0.071 - 0.238 [L/m
2
]
Information
Film Thickness : WET 71 - 238 [micron]DRY 30 - 100 [micron]
() 5 oC 10 oC 20 oC 30 oC
Drying Time Surface Dry 3hrs. 2hrs. 1hr. 30min.Hard Dry 12hrs. 8hrs. 5hrs. 4hrs.
Painting Interval Min - - - -Max - - - -
Dry to Launch Min 24hrs. 18hrs. 12hrs. 10hrs.
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum 0
degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 1.5 - 2.5Pa・s
Tip No. : (GRACO)617 - 723 Paint Output Pressuer: 11.7 - 14.7[MPa] Spray Speed : 60 - 80[cm/sec]
Thinner : RAVAX THINNER, Thinning: 0 - 5 % by Volume
Preceding Coats : SEA GRANDPRIX CF-10, SEA GRANDPRIX CF-10 L, SEA GRANDPRIX 1000, SEA GRANDPRIX 500
Conditionof
Application
Subsequent Coats : -
Packaging One pack product
Notes 1.This is a temporary anti-fouling paint for an out fitting period of New buildings at the heavy fouled area such as Tokyo bay, Ise bay and Oosaka bay etc.2. Any other subsequent coats can not be compatible on this paint due to special paint for non final dock system
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
SEA GRANDPRIX CF-10(SGP CF-10)
Sep.2006
No. 5917K
SEA GRANDPRIX CF-10 , tin and copper free self polishing antifouling paint based on the specific polymer, is designed for deep sea vessels. Excellent antifouling effect is derived from the highly active hydrolysis polymer which ensures maximum effectiveness and leaching of the biocides. Activation at the surface is maintained by control of hydrolysis thus providing long term antifouling protection commensurate with the applied film thickness.
TECHNICAL DATA
Type Tin and copper free self polishing antifouling
Recommened
Use
Antifouling paint on steel ship's bottom for world wide service with extended dry-docking interval
Color : Red, Light red, Purple Flash Point : 25.0 [degC] Solid by volume : 44 (+-2) [volume %] VOC : 487 [g/L] Coverage(Theoretical): 0.17 - 0.364 [L/m
2
]
Information
Film Thickness : WET 170 - 364 [micron]DRY 75 - 160 [micron]
() -5 oC 0 oC 5 oC 10 oC 20 oC 30 oC
Drying Time Surface Dry 6hrs. 4hrs. 3hrs. 2hrs. 1hr. 30mins.Hard Dry 22hrs. 16hrs. 12hrs. 8hrs. 5hrs. 4hrs.
Painting Interval Min 22hrs. 16hrs. 12hrs. 8hrs. 5hrs. 4hrs.Max - - - - - -
Dry to Launch Min 48hrs. 36hrs. 24hrs. 18hrs. 12hrs. 10hrs.
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum -5
degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 1.5 - 2.5Pa・s
Tip No. : (GRACO)621 - 723 Paint Output Pressuer: 11.7 - 14.7[MPa] Spray Speed : 60 - 80[cm/sec]
Thinner : RAVAX THINNER, Thinning: 0 - 5 % by Volume
Preceding Coats : BANNOH 500 N, BANNOH 500 R, SILVAX SQ-K, HIPER AC, RAVAX AC-HB etc.
Conditionof
Application
Subsequent Coats : -
Packaging One pack product
Notes 1.There is a risk of antifoulings becoming fouled when ships are stationary for three consecutive weeks or more,particularly in areas with a high risk of fouling.2.Below 10 degC, extra solvent maybe required to obtain application viscosity.3.But too much solvent results in reduced sag resistance and paint film property.4.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
SEA GRANDPRIX CF-10 L(SGP CF-10 L)
Sep.2006
No. 5917L
SEA GRANDPRIX CF-10 L , tin and copper free self polishing antifouling paint based on the specific polymer, is designed for deep sea vessels. Excellent antifouling effect is derived from the active hydrolysis polymer which ensures maximum effectiveness and leaching of the biocides. Activation at the surface is maintained by control of hydrolysis thus providing long term antifouling protection commensurate with the applied film thickness.
TECHNICAL DATA
Type Tin and copper free self polishing antifouling
Recommened
Use
Antifouling paint on steel ship's bottom for world wide service with extended dry-docking interval
Color : Red, Light red, Purple Flash Point : 24.5 [degC] Solid by volume : 44 (+-2) [volume %] VOC : 484 [g/L] Coverage(Theoretical): 0.17 - 0.364 [L/m
2
]
Information
Film Thickness : WET 170 - 364 [micron]DRY 75 - 160 [micron]
(D.F.T. 100micron) 5 oC 10 oC 20 oC 30 oC
Drying Time Surface Dry 3hrs. 2hrs. 1hr. 30mins.Hard Dry 12hrs. 8hrs. 5hrs. 4hrs.
Painting Interval Min 12hrs. 8hrs. 5hrs. 4hrs.Max - - - -
Dry to Launch Min 24hrs. 18hrs. 12hrs. 10hrs.
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum 0
degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 1.5 - 2.5Pa・s
Tip No. : (GRACO)621 - 723 Paint Output Pressuer: 11.7 - 14.7[MPa] Spray Speed : 60 - 80[cm/sec]
Thinner : RAVAX THINNER, Thinning: 0 - 5 % by Volume
Preceding Coats : BANNOH 500 N, BANNOH 500 R, SILVAX SQ-K, HIPER AC, RAVAX AC-HB
Conditionof
Application
Subsequent Coats : -
Packaging One pack product
Notes 1.There is a risk of antifoulings becoming fouled when ships are stationary for three consecutive weeks or more,particularly in areas with a high risk of fouling.2.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
SEA GRANDPRIX CF-10 L M(SGP CF-10 L M)
Mar.2006
No. 5928
SEA GRANDPRIX CF-10 L M , tin and copper free self polishing antifouling paint based on the specific polymer, is designed for deep sea vessels. Excellent antifouling effect is derived from the highly active hydrolysis polymer which ensures maximum effectiveness and leaching of the biocides. Activation at the surface is maintained by control of hydrolysis thus providing long term antifouling protection commensurate with the applied film thickness.
TECHNICAL DATA
Type Tin and copper free self polishing antifouling
Recommened
Use
Antifouling paint on steel ship's bottom for world wide service with extended dry-docking interval
Color : Red, Light red Flash Point : 24.5 [degC] Solid by volume : 43 (+-2) [volume %] VOC : 491 [g/L] Coverage(Theoretical): 0.174 - 0.372 [L/m
2
]
Information
Film Thickness : WET 174 - 372 [micron]DRY 75 - 160 [micron]
() 5 oC 10 oC 20 oC 30 oC
Drying Time Surface Dry 3hrs. 2hrs. 1hr. 30mins.Hard Dry 12hrs. 8hrs. 5hrs. 4hrs.
Painting Interval Min 12hrs. 8hrs. 5hrs. 4hrs.Max - - - -
Dry to Launch Min 24hrs. 18hrs. 12hrs. 10hrs.
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum 0
degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 1.5 - 2.5Pa・s
Tip No. : (GRACO)621 - 723 Paint Output Pressuer: 11.7 - 14.7[MPa] Spray Speed : 60 - 80[cm/sec]
Thinner : RAVAX THINNER, Thinning: 0 - 5 % by Volume
Preceding Coats : BANNOH 500 N, BANNOH 500 R, SILVAX SQ-K, HIPER AC, RAVAX AC-HB etc.
Conditionof
Application
Subsequent Coats : -
Packaging One pack product
Notes 1.There is a risk of antifoulings becoming fouled when ships are stationary for three consecutive weeks or more,particularly in areas with a high risk of fouling.2.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
SEA GRANDPRIX CF-10 M(SGP CF-10 M)
Mar.2006
No. 5927
SEA GRANDPRIX CF-10 M , tin and copper free self polishing antifouling paint based on the specific polymer, is designed for deep sea vessels. Excellent antifouling effect is derived from the highly active hydrolysis polymer which ensures maximum effectiveness and leaching of the biocides. Activation at the surface is maintained by control of hydrolysis thus providing long term antifouling protection commensurate with the applied film thickness.
TECHNICAL DATA
Type Tin and copper free self polishing antifouling
Recommened
Use
Antifouling paint on steel ship's bottom for world wide service with extended dry-docking interval
Color : Red, Light red Flash Point : 25.0 [degC] Solid by volume : 43 (+-2) [volume %] VOC : 494 [g/L] Coverage(Theoretical): 0.174 - 0.372 [L/m
2
]
Information
Film Thickness : WET 174 - 372 [micron]DRY 75 - 160 [micron]
() 5 oC 10 oC 20 oC 30 oC
Drying Time Surface Dry 3hrs. 2hrs. 1hr. 30mins.Hard Dry 12hrs. 8hrs. 5hrs. 4hrs.
Painting Interval Min 12hrs. 8hrs. 5hrs. 4hrs.Max - - - -
Dry to Launch Min 24hrs. 18hrs. 12hrs. 10hrs.
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum 0
degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 1.5 - 2.5Pa・s
Tip No. : (GRACO)621 - 723 Paint Output Pressuer: 11.7 - 14.7[MPa] Spray Speed : 60 - 80[cm/sec]
Thinner : RAVAX THINNER, Thinning: 0 - 5 % by Volume
Preceding Coats : BANNOH 500 N, BANNOH 500 R, SILVAX SQ-K, HIPER AC, RAVAX AC-HB etc.
Conditionof
Application
Subsequent Coats : -
Packaging One pack product
Notes 1.There is a risk of antifoulings becoming fouled when ships are stationary for three consecutive weeks or more,particularly in areas with a high risk of fouling.2.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
SEA GRANDPRIX CF-20(SGP CF20)
Mar.2006
No. 5919
SEA GRANDPRIX CF-20 , a tin free self polishing antifouling paint based on the specific polymer without cuprous oxide, is designed for the coastal ships sailing in the heavy fouled area . Excellent antifouling effect is derived from the highly active hydrolysis polymer which ensures maximum effectiveness and leaching of the biocides. Activation at the surface is maintained by control of hydrolysis thus providing long term antifouling protection commensurate with the applied film thickness.
TECHNICAL DATA
Type Tin free self polishing antifouling without cuprous oxide
Recommened
Use
On the ship bottom for coastal steel ships and aluminum boats
Color : Red, Pink, Blue Flash Point : 25.0 [degC] Solid by volume : 41 (+-2) [volume %] VOC : 518 [g/L] Coverage(Theoretical): 0.18 - 0.37 [L/m
2
]
Information
Film Thickness : WET 183 - 366 [micron]DRY 75 - 150 [micron]
(D.F.T. 100micron) 5 oC 10 oC 20 oC 30 oC
Drying Time Surface Dry 3hrs. 2hrs. 1hr. 30mins.Hard Dry 12hrs. 8hrs. 5hrs. 4hrs.
Painting Interval Min 12hrs. 8hrs. 5hrs. 4hrs.Max - - - -
Dry to Launch Min 24hrs. 18hrs. 12hrs. 10hrs.
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum 0
degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 1.5 - 2.5Pa・s
Tip No. : (GRACO)621 - 723 Paint Output Pressuer: 11.7 - 14.7[MPa] Spray Speed : 60 - 80[cm/sec]
Thinner : RAVAX THINNER, Thinning: 0 - 5 % by Volume
Preceding Coats : SILVAX SQ-K, VINYL AC-HB, HIPER AC, RAVAX AC-HB, etc.
Conditionof
Application
Subsequent Coats : -
Packaging One pack product
Notes 1.There is a risk of antifoulings becoming fouled when ships are stationary for three consecutive weeks or more,particularly in areas with a high risk of fouling.2.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
SEA GRANDPRIX FRP(SGP FRP)
Feb.2007
No. 5923
SEA GRANDPRIX FRP is a tin free self polishing antifouling paint based on the specific polymer with highly hydrolysis activity. Excellent antifouling effect is derived from the highly active polymer which ensures maximum effectiveness and leaching of the biocides. Activation at the surface is maintained by control of hydrolysis thus providing execllent antifouling performance.
TECHNICAL DATA
Type Tin free self polishing antifouling paint
Recommened
Use
Antifouling paint for FRP boat and plesure boat.
Color : Light red Flash Point : 23.2 [degC] Solid by volume : 42 (+-2) [volume %] VOC : 494 [g/L] Coverage(Theoretical): 0.119 - 0.238 [L/m
2
]
Information
Film Thickness : WET 119 - 238 [micron]DRY 50 - 100 [micron]
(D.F.T. 50micron) 5 oC 10 oC 20 oC 30 oC
Drying Time Surface Dry 3hrs. 2hrs. 1hr.Hard Dry 12hrs. 8hrs. 5hrs.
Painting Interval Min 12hrs. 8hrs. 5hrs.Max
Dry to Launch Min 24hrs. 18hrs. 12hrs.
Method of Application : Brush, Roller Weather : Temperature : Minimum 0
degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 1.5 - 2.5Pa・s
Tip No. : (GRACO)619 - 625 Paint Output Pressuer: 11.7 - 14.7[MPa] Spray Speed : 60 - 80[cm/sec]
Thinner : RAVAX THINNER, Thinning: 0 - 5 % by Volume
Preceding Coats : FRP PRIMER
Conditionof
Application
Subsequent Coats : -
Packaging One pack product
Notes VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
SEAJET 015(SJ 015)
Jan.2006
No. 9102
SEAJET015based on special acrylic resin, provides excellent adhesion to FRP surfaces and subsequent antifouling paint. It is quick drying and forms a tough yet flexible film which is highly resistant to weather and sea water.
TECHNICAL DATA
Type Acrylic resin primer
Recommened
Use
As aprimer and binder coat for FRP boats' bottom
Color : Silver Flash Point : 23.0 [degC] Solid by volume : 35 (+-2) [volume %] VOC : 560 [g/L] Coverage(Theoretical): 0.11 [L/m
2
]
Information
Film Thickness : WET 114 [micron]DRY 40 [micron]
() 5 oC 10 oC 20 oC 30 oC
Drying Time Surface Dry 40mins. 30mins. 20mins. 15mins.Hard Dry 4hrs. 3hrs. 2hrs. 1.5hrs.
Painting Interval Min 5hrs. 4hrs. 3hrs. 2hrs.Max - - - -
Method of Application : Airless spray; Brush; Roller Weather : Temperature : Minimum 0
degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 40[sec]
Tip No. : (IWATA)W-77-2S,etc Spray Speed : 80 - 100[cm/sec]
Thinner : SEAJET THINNER A, Thinning: 15 - 25 % by Volume
Preceding Coats : -
Conditionof
Application
Subsequent Coats : SEAJET033, SEAJET034, SEAJET035
Packaging One pack product
Notes VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
SEAJET 033(SJ033)
Feb.2006
No. 9110
SEAJET033 is a tin free erodible antifouling paint with self-polishing action in service and good protection against marine organisms. The specific vehicle composition provides a unique hydration mechanism during operation , resulting excellent antifouling performance.
TECHNICAL DATA
Type Tin free antifouling paint
Recommened
Use
Antifouling paint on FRP ship's bottom
Color : Red, Blue, Black, Shark white Flash Point : 30.0 [degC] VOC : 456 [g/L] Coverage(Theoretical): 0.107 [L/m
2
]
Information
Film Thickness : WET 98 [micron]DRY 50 [micron]
() 5 oC 10 oC 20 oC 30 oC
Drying Time Surface Dry 3hrs. 2hrs. 1hr. 30mins.Hard Dry 12hrs. 7hrs. 5hrs. 4hrs.
Painting Interval Min 12hrs. 7hrs. 5hrs. 4hrs.Max - - - -
Dry to Launch Min 24hrs. 16hrs. 12hrs. 8hrs.
Method of Application : Airless spray, Air spray, Brush, Roller Weather : Temperature : Minimum 0
degC, Humidity : Maximum 85 %R.H. Thinner : SEAJET THINNER A,
Thinning: 0 - 5 % by Volume Preceding Coats : SEAJET 015, RAVAX AC-HB, FRP PRIMER, etc.
Conditionof
Application
Subsequent Coats : -
Packaging One pack product
Notes 1.There is a risk of antifoulings becoming fouled when ships are stationary for three consecutive weeks or more,particularly in areas with a high risk of fouling.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
SEAJET 132(SJ 132)
Feb.2006
No. 9121
SEAJET 132 is a polyurethane based high gloss finish coat. It has excellent gloss retention and durability and good adhesion property. It is suitable for top coat of pleasure boat and yacht.
TECHNICAL DATA
Type Polyurethane paint
Recommened
Use
Top coat for pleasure boat and yacht.
Mixing Ratio : Color :
Base : Hardener = 5 : 1 [by volume]White, Blue, Red , Yellow, Green, Orange
Flash Point : Base = 25.3, Hardener = 29.5 [degC] Solid by volume : 45 (+-2) [volume %] VOC : 462 [g/L] Coverage(Theoretical): 0.077 - 0.11 [L/m
2
]
Information
Film Thickness : WET 77 - 110 [micron]DRY 35 - 50 [micron]
() 5 oC 10 oC 20 oC 30 oC
Drying Time Surface Dry 50mins. 30mins. 20mins. 10mins.Hard Dry 12hrs. 8hrs. 6hrs. 4hrs.
Painting Interval Min 8hrs. 6hrs. 4hrs. 2hrs.Max - - - -
Pot Life 24hrs. 20hrs. 16hrs. 8hrs.
Method of Application : Air spray Weather : Temperature : Minimum 0
degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 15 - 20[sec]
Tip No. : (IWATA Spraygun)W-71-3S Spray Speed : 80 - 100[cm/sec]
Thinner : SEAJET B THINNER, Thinning: 15 - 30 % by Volume
Preceding Coats : SEAJET111
Conditionof
Application
Subsequent Coats : -
Packaging Two pack product
Notes VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
SEAJET 137(SJ137)
Feb.2006
No. 9124
SEAJET137 is a finishing coat based on acrylic resin and drying by evaporation of the solvents. It has excellent adhesion property, weathering resistance and gloss and colour retention.
TECHNICAL DATA
Type Acrylic finish paint
Recommened
Use
Top coat for pleasure boat and yacht.
Color : White, As specified, , , Flash Point : 25.7 [degC] Specific Gravity : 1.18 [g/mL] Solid by volume : [volume %] VOC : 598 [g/L] Coverage(Theoretical): 0.087 - 0.145 [L/m
2
]
Information
Film Thickness : WET 100 - 143 [micron]DRY 35 - 50 [micron]
(D.F.T. 35micron) 5 oC 10 oC 20 oC 30 oC
Drying Time Surface Dry 1.5hrs. 1.2hr. 1hr. 30mins.Hard Dry 12hrs. 8hrs. 5hrs. 4hrs.
Painting Interval Min 12hrs. 8hrs. 5hrs. 4hrs.Max - - - -
Method of Application : Airless spray, Air spray, Brush, Roller Weather : Temperature : Minimum 0
degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : (IWATA CUP)15 - 20[sec]
Spray Speed : 30 - 50[cm/sec] Thinner : SEAJET THINNER A,
Thinning: 0 - 10 % by Volume Preceding Coats : SAEJET111
Conditionof
Application
Subsequent Coats : -
Packaging One pack product
Notes VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
SEAJET 145W(SJ 145W)
Feb.2006
No. 9130
SEAJET 145W is epoxy resin based putty with the performance of super light weight, good adhesion, good filling and good fairing.
TECHNICAL DATA
Type Epoxy resin based putty
Recommened
Use
Filling, fairing of wooden, steel, aluminium or FRP substrates.
Mixing Ratio : Color :
Base : Hardener = 67 : 33 [by volume]Pink
Flash Point : Base = -, Hardener = - [degC] VOC : 0 [g/L] Coverage(Theoretical): 2 [L/m
2
]
Information
Film Thickness : DRY 2000 [micron]
() 5 oC 10 oC 20 oC 30 oC
Drying Time Surface Dry 5hrs. 4hrs. 2hrs.Hard Dry 24hrs. 20hrs. 10hrs.
Painting Interval Min 20hrs. 16hrs. 8hrs.Max - - -
Pot Life 4hrs. 2hrs. 20mins.
Method of Application : Spatula; Trowel Weather : Temperature : 5 - 25
degC, Humidity : Maximum 85 %R.H. Thinner : - Preceding Coats : SEAJET010,SEAJET020
Conditionof
Application
Subsequent Coats : SEAJET020,etc
Packaging Two pack product
Notes VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
SILICON HR PRIMER(SN HR PR)
Oct.2006
No. 8032
SILICON HR PRIMER is a silicon resin primer based on silicon resin with curing accelerator .It has the following characteristics.1. Excellent heat resistance (up to 700 degC)2. Excellent weathering resistance3. Excellent application workability4. Excellent adhesion property
TECHNICAL DATA
Type Silicone resin heat resisting primer
Recommened
Use
As undercoat for boiler, cylinder of engine, inside of exhaust pipes, radiator, oil burner, etc.
Mixing Ratio : Color :
Base : Curing Accelerator = 100 : 1.53 [by volume]White
Flash Point : Base = 19.3, Curing Accelerator = 38.3 [degC] Solid by volume : 38 (+-2) [volume %] VOC : 542 [g/L] Coverage(Theoretical): 0.066 [L/m
2
]
Information
Film Thickness : WET 66 [micron]DRY 25 [micron]
() 5 oC 10 oC 20 oC 30 oC
Drying Time Surface Dry 1hr. 50mins. 30mins. 20mins.Hard Dry 7hrs. 5hrs. 3hrs. 1hr.
Painting Interval Min 24hrs. 20hrs. 16hrs. 10hrs.Max - - - -
Pot Life 32hrs. 28hrs. 24hrs. 16hrs.
Method of Application : Airless spray, Brush Weather : Temperature : Minimum 0
degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : (Fc#4)25 - 35[sec]
Tip No. : (GRACO)415 Paint Output Pressuer: 8.8 - 11.8[MPa] Spray Speed : 70 - 100[cm/sec]
Thinner : SILICON THINNER, Thinning: 5 - 10 % by Volume
Preceding Coats : -
Conditionof
Application
Subsequent Coats : SILICON HR SILVER HG, SILICON HR
Packaging Two pack product
Notes 1.Paint film should be baked for 2 hours at 200 degC to complete curing.2.Total paint film thickness of painting specification should be less than 150 micron.3.Surface preparation: In case of direct application to the steel surface, ISO Sa2.5. In case of application on shop primer coated surface, ISO St3 is required. The surface to be painted must be clean, free from rust, oil grease or other foreign matter using power wash, detergent, or solvent wipe.4. Mixing ratio of Base : Curing Accelerator (by weight) is 100:1.5.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
SILICON HR SILVER HG(SN HR SIL HG)
Feb.2006
No. 8035
SILICON HR SILVER HG, is a silicone heat resisting paint based on silicone resin pigmented and aluminium pigment.It has the following advantages;1. Excellent heat resistance (up to 400 degC)2. Excellent weather resistance3. Excellent application workability4. Excellent adhesion property
TECHNICAL DATA
Type Silicone resin heat resisting aluminium paint
Recommened
Use
As finish coat for boiler, cylinder of engine, inside of exhaust pipes, radiator, oil burner, etc.
Mixing Ratio : Color :
Base : Curing Accelerator = 100 : 1.21 [by volume]SILVER
Flash Point : Base = 19.5, Curing Accelerator = 38.3 [degC] Solid by volume : 34 (+-2) [volume %] VOC : 586 [g/L] Coverage(Theoretical): 0.045 - 0.059 [L/m
2
]
Information
Film Thickness : WET 45 - 59 [micron]DRY 15 - 20 [micron]
(D.F.T. 15micron) 5 oC 10 oC 20 oC 30 oC
Drying Time Surface Dry 1hr. 50mins. 30mins. 20mins.Hard Dry 7hrs. 5hrs. 3hrs. 1hrs.
Painting Interval Min 20hrs. 16hrs. 12hrs. 8hrs.Max - - - -
Pot Life 32hrs. 28hrs. 24hrs. 16hrs.
Method of Application : Airless spray, Brush Weather : Temperature : Minimum 0
degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : (Fc#4)10 - 20[sec]
Tip No. : (GRACO)415 Paint Output Pressuer: 8.8 - 11.8[MPa] Spray Speed : 70 - 100[cm/sec]
Thinner : SILICON THINNER, Thinning: 5 - 10 % by Volume
Preceding Coats : SILICON HR PRIMER
Conditionof
Application
Subsequent Coats : -
Packaging Two pack product
Notes 1. Paint film should be baked for 2 hours at 200 degC to complete curing.2. Total paint film thickness of painting specification should be below 150 micron.3. Surface preparation : In case of direct application to the steel surface, ISO Sa 2.5. In case of application on shop primer coated surface, ISO St 3 is required. The surface to be painted must be clean, free from rust, dirt, oil grease or other foreign matter using power wash, detergent, or solvent wipe.4. Mixing ratio of Base : Curing Accelerator (by weight) is 100:1.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
5. VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
SILICON HR SILVER(SN HR SIL)
Feb.2006
No. 8034
SILICON HR SILVER, is a silicone heat resisting finish on inorganic zinc primer based on silicone resin pigmented with aluminium pigment.It has the following advantages;1. Excellent heat resistance (up to 700 degC)2. Excellent weather resistance3. Excellent application workability4. Excellent compatibility with inorganic zinc primer
TECHNICAL DATA
Type Silicone resin heat resisting aluminium paint
Recommened
Use
As finish coat for boiler, cylinder of engine, inside of exhaust pipes, radiator, oil burner, etc.
Mixing Ratio : Color :
Base : Curing Accelerator = 100 : 1.21 [by volume]Silver
Flash Point : Base = 22.3, Curing Accelerator = 38.3 [degC] Solid by volume : 25 (+-2) [volume %] VOC : 650 [g/L] Coverage(Theoretical): 0.06 - 0.08 [L/m
2
]
Information
Film Thickness : WET 60 - 80 [micron]DRY 15 - 20 [micron]
() 5 oC 10 oC 20 oC 30 oC
Drying Time Surface Dry 1hr. 50mins. 30mins. 20mins.Hard Dry 7hrs. 5hrs. 3hrs. 1hr.
Painting Interval Min 24hrs. 20hrs. 16hrs. 10hrs.Max - - - -
Pot Life 32hrs. 28hrs. 24hrs. 16hrs.
Method of Application : Airless spray, Brush Weather : Temperature : Minimum 0
degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : (Fc#4)10 - 20[sec]
Tip No. : (GRACO)415 Paint Output Pressuer: 8.8 - 11.8[MPa] Spray Speed : 70 - 100[cm/sec]
Thinner : SILICON THINNER, Thinning: 5 - 10 % by Volume
Preceding Coats : SILICON HR PRIMER
Conditionof
Application
Subsequent Coats : -
Packaging Two pack product
Notes 1. Paint film should be baked for 2 hours at 200 degC to complete curing.2. Surface preparation : The surface to be painted must be clean, free from rust, dirt, oil grease or other foreign matter using power wash, detergent, or solvent wipe.3. Total thickness of specification should be less than 150 micron.4. Mixing ratio of Base : Curing Accelerator (by weight) is 100:1.5.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
SILICON HR(SN HR)
Feb.2006
No. 8033
SILICON HR, is a silicone heat resisting paint based on silicone resin pigmented with heat resisting pigment.It has the following advantages;1. Excellent heat resistance (up to 700 degC)2. Excellent weather resistance3. Excellent application workability4. Excellent adhesion property
TECHNICAL DATA
Type Silicone resin heat resisting paint
Recommened
Use
As finish coat for boiler, cylinder of engine, inside of exhaust pipes, radiator, oil burner, etc.
Mixing Ratio : Color :
Base : Curing Accelerator = 100 : 1.42 [by volume]White, Black, Red brown, Light colours
Flash Point : Base = 20, Curing Accelerator = 38.3 [degC] Solid by volume : 38 (+-2) [volume %] VOC : 546 [g/L] Coverage(Theoretical): 0.04 - 0.066 [L/m
2
]
Information
Film Thickness : WET 40 - 66 [micron]DRY 15 - 25 [micron]
() 5 oC 10 oC 20 oC 30 oC
Drying Time Surface Dry 1hr. 50mins. 30mins. 20mins.Hard Dry 7hrs. 5hrs. 3hrs. 1hrs.
Painting Interval Min 24hrs. 20hrs. 16hrs. 10hrs.Max - - - -
Pot Life 32hrs. 28hrs. 24hrs. 16hrs.
Method of Application : Airless spray, Brush Weather : Temperature : Minimum 0
degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : (Fc#4)25 - 35[sec]
Tip No. : (GRACO)415 Paint Output Pressuer: 8.8 - 11.8[MPa] Spray Speed : 70 - 100[cm/sec]
Thinner : SILICON THINNER, Thinning: 5 - 10 % by Volume
Preceding Coats : SILICON HR PRIMER
Conditionof
Application
Subsequent Coats : -
Packaging Two pack product
Notes 1. Paint film should be baked for 2 hours at 200 degC to complete curing.2. Total paint film thickness of painting specification should be less than 150 micron.3. Surface preparation : The surface to be painted must be clean, free from rust, dirt, oil grease or other foreign matter using power wash, detergent, or solvent wipe.4. Mixing ratio of Base : Curing Accelerator (by weight) is 100:1.5.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
SILVA SPAR No.500(SIS 500)
Feb.2006
No. 8000
SILVA SPAR No.500 is an alkyd resin based aluminium paint with outstanding heat resisting and rust-preventing properties. It presents a beautiful appearance. SILVA SPAR No.500 successfully withstands temperatures of up to 150ーC.
TECHNICAL DATA
Type Alkyd/Aluminium heat resisting paint
Recommened
Use
As a protective coating on steel surfaces reaching high temperatures
Mixing Ratio : Color :
Varnish : Aluminium paste = 89 : 11 [by volume]Metallic Silver
Flash Point : Varnish = 35.0, Aluminium paste = 43.3 [degC] Solid by volume : 44 (+-2) [volume %] VOC : 451 [g/L] Coverage(Theoretical): 0.034 - 0.056 [L/m
2
]
Information
Film Thickness : WET 34 - 56 [micron]DRY 15 - 25 [micron]
() 0 oC 5 oC 10 oC 20 oC 30 oC
Drying Time Surface Dry 4hrs. 3hrs. 2hrs. 1hr. 30mins.Hard Dry 30hrs. 20hrs. 13hrs. 7hrs. 5hrs.
Painting Interval Min 72hrs. 48hrs. 24hrs. 16hrs. 12hrs.Max - - - - -
Pot Life 32hrs. 32hrs. 24hrs. 16hrs. 8hrs.
Method of Application : Airless spray, Brush Weather : Temperature : Minimum 0
degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : (Fc#4)40[sec]
Tip No. : (GRACO)713 Paint Output Pressuer: 10.7 - 13.8[MPa] Spray Speed : 100 - 120[cm/sec]
Thinner : MARINE THINNER, Thinning: - % by Volume
Preceding Coats : LZI PRIMER HB, RED LEAD PRIMER QD, Alkyd resin based primer
Conditionof
Application
Subsequent Coats : -
Packaging Two pack product
Notes 1.Applying within the recommended film thickness range to avoid the wrinkling.2.After adding the aluminium paste to the base component, applying early to keep the brightness.3.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
SILVAX SQ-K(SX SQ K)
Mar.2006
No. 3007
SILVAX SQ-K, modified vinyl paint, forms a practically impervious barrier against water and provides an excellent key for subsequent anti-fouling paints.
TECHNICAL DATA
Type Modified vinyl anti-corrosive paint.
Recommened
Use
Anti-corrosive for steel ships bottom, Binder-coat for anti-fouling paint
Color : S(Silver), SR(Pink silver) Flash Point : 18.8 [degC] Solid by volume : 30 [volume %] VOC : 611 [g/L] Coverage(Theoretical): 0.13 - 0.27 [L/m
2
]
Information
Film Thickness : WET 133 - 266 [micron]DRY 40 - 80 [micron]
(D.F.T. 80micron) 5 oC 10 oC 20 oC 30 oC
Drying Time Surface Dry 1.5hrs. 1hr. 40mins. 30mins.Hard Dry 12hrs. 10hrs. 8hrs. 6hrs.
Painting Interval Min (AC)(AF)
12hrs.15hrs.
10hrs.12hrs.
8hrs.9hrs.
6hrs.8hrs.
Max (AC)(AF)
-7days
-7days
-7days
-7days
Method of Application : Airless spray; Brush; Roller Weather : Temperature : Minimum 0
degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : (Fc#4)80[sec]
Tip No. : (GRACO)719,721 Paint Output Pressuer: 11.7 - 14.7[MPa] Spray Speed : 60 - 80[cm/sec]
Thinner : VINYL THINNER, Thinning: 0 - 10 % by Volume
Preceding Coats : BISCON AC-QL, BISCON AC-AL, etc.
Conditionof
Application
Subsequent Coats : SEA GRANDPRIX 100,200 series
Packaging One pack product
Notes 1.Before application of subsequent coat, clean the surface by fresh water washing or other means if surface is contaminated by chalking or impurities.2. VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
SILVAX SQ-M(SX SQ M)
Mar.2006
No. 3008
SILVAX SQ-M, modified vinyl paint, forms a practically impervious barrier against water and provides an excellent key for subsequent anti-fouling paints.
TECHNICAL DATA
Type Modified vinyl anti-corrosive paint.
Recommened
Use
Anti-corrosive for steel ships bottom, Binder-coat for anti-fouling paint
Color : S(Silver), R(Red silver brown) Flash Point : 18.8 [degC] Solid by volume : 36 [volume %] VOC : 571 [g/L] Coverage(Theoretical): 0.138 - 0.259 [L/m
2
]
Information
Film Thickness : WET 110 - 207 [micron]DRY 40 - 75 [micron]
(D.F.T. 75micron) 5 oC 10 oC 20 oC 30 oC
Drying Time Surface Dry 1hr. 45mins. 30mins. 25mins.Hard Dry 8hrs. 6.5hrs. 5hrs. 4hrs.
Painting Interval Min (AC)(AF)
8hrs.14hrs.
6.5hrs.11hrs.
5hrs.8hrs.
4hrs.7hrs.
Max (AC)(AF)
-7days
-7days
-7days
-7days
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum 0
degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : (Fc#4)80[sec]
Tip No. : (GRACO)719,721 Paint Output Pressuer: 11.7 - 14.7[MPa] Spray Speed : 60 - 80[cm/sec]
Thinner : VINYL THINNER, Thinning: 0 - 10 % by Volume
Preceding Coats : BISCON AC, BISCON AC-HB, BISCON AC-QL, BISCON AC-QL HB, SILVAX SQ-M, BANNOH 500 etc
Conditionof
Application
Subsequent Coats : MARINE STAR 10,20 series, TFA-10 series, SILVAX SQ-M
Packaging One pack product
Notes 1. Before application of subsequent coat, clean the surface by fresh water washing or other means if surface is contaminated by chalking or impurities.2.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
TFA FLAT(TFA F)
Mar.2006
No. 5873
TFA FLAT S is a tin free antifouling paint with self polishing action. The product is used for fouling control on the flat bottom.
TECHNICAL DATA
Type Tin free self polishing antifouling paint
Recommened
Use
Antifouling paint on steel ships' flat bottom for world wide service with extended drydocking interval.
Color : Red, Pink Flash Point : 23.0 [degC] Solid by volume : 52 (+-2) [volume %] VOC : 457 [g/L] Coverage(Theoretical): 0.095 - 0.19 [L/m
2
]
Information
Film Thickness : WET 95 - 190 [micron]DRY 50 - 100 [micron]
() 5 oC 10 oC 20 oC 30 oC
Drying Time Surface Dry 3hrs. 2hrs. 1hr. 30mins.Hard Dry 12hrs. 8hrs. 5hrs. 4hrs.
Painting Interval Min 12hrs. 8hrs. 5hrs. 4hrs.Max - - - -
Dry to Launch Min 24hrs. 18hrs. 12hrs. 10hrs.
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum 0
degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : (Fc#4)90[sec]
Tip No. : (GRACO)621(721) - 633(733) Paint Output Pressuer: 11.7 - 14.7[MPa] Spray Speed : 60 - 80[cm/sec]
Thinner : RAVAX THINNER, Thinning: 0 - 5 % by Volume
Preceding Coats : SILVAX SQ, VINYL AC-HB, RAVAX AC-P, RAVAX AC, RAVAX AC-HB,
Conditionof
Application
Subsequent Coats : -
Packaging One pack product
Notes 1.There is a risk of antifoulings becoming fouled when ships are stationary for three consecutive weeks or more,particularly in areas with a high risk of fouling.2.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
TFA-10(TFA 10)
Mar.2006
No. 5865G
TFA-10 is a tin free antifouling paint with self polishing action in service and long protection against marine organisms. The specific vehicle composition provides a unique hydration mechanism during operation , resulting in long lasting antifouling performance.
TECHNICAL DATA
Type Tin free self polishing antifouling paint
Recommened
Use
Antifouling paint on steel ship's bottom for world wide service with extended dry-docking interval.
Color : Dark red, Light red Flash Point : 23.0 [degC] Solid by volume : 55 (+-2) [volume %] VOC : 476 [g/L] Coverage(Theoretical): 0.18 - 0.27 [L/m
2
]
Information
Film Thickness : WET 182 - 273 [micron]DRY 100 - 150 [micron]
(D.F.T. 100micron) -5 oC 0 oC 5 oC 10 oC 20 oC 30 oC
Drying Time Surface Dry 6hrs. 4hrs. 3hrs. 2hrs. 1hr. 30mins.Hard Dry 22hrs. 16hrs. 12hrs. 8hrs. 5hrs. 4hrs.
Painting Interval Min 22hrs. 16hrs. 12hrs. 8hrs. 5hrs. 4hrs.Max - - - - - -
Dry to Launch Min 48hrs. 36hrs. 24hrs. 18hrs. 12hrs. 10hrs.
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum -5
degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : (Fc#4)90[sec]
Tip No. : (GRACO)621(721) - 635(735) Paint Output Pressuer: 11.7 - 14.7[MPa] Spray Speed : 60 - 80[cm/sec]
Thinner : RAVAX THINNER, Thinning: 0 - 5 % by Volume
Preceding Coats : SILVAX SQ-M, VINYL AC-HB, RAVAX AC HB, RAVAX AC-P, HIPER AC,
Conditionof
Application
Subsequent Coats : -
Packaging One pack product
Notes 1.There is a risk of antifoulings becoming fouled when ships are stationary for three consecutive weeks or more,particularly in areas with a high risk of fouling.2.Below 10 degC, extra solvent maybe required to obtain application viscosity.3.But too much solvent results in reduced sag resistance and paint film property.4.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
UMEGUARD PU(UG PU)
Feb.2006
No. 6165
UMEGUARD PU is based on epoxy polyurethane resin. It gives excellent physical properties such as adhesion, flexibility, toughness and abrasion resistance, etc. and chemical resistance to water and sea water. It has good adhesion to the existing paint surface. UMEGUARD PU is suitable for repair of ships by simply surface preparation such as disc sanding or chipping, and for newbuilding ships by simply surface preparation such as brooming or hand brushing.
TECHNICAL DATA
Type Epoxy urethane resin paint, high build
Recommened
Use
Deck, Hatch cover, etc.
Mixing Ratio : Color :
Base : Hardener = 88 : 12 [by volume]White, Grey, White, Green
Flash Point : Base = 6.0, Hardener = 2.0 [degC] VOC : 445 [g/L] Coverage(Theoretical): 0.16 - 0.32 [L/m
2
]
Information
Film Thickness : WET 160 - 320 [micron]DRY 100 - 200 [micron]
(D.F.T. 200micron) 5 oC 10 oC 20 oC 30 oC
Drying Time Surface Dry 50mins. 45mins. 35mins. 30mins.Hard Dry 22hrs. 16hrs. 10hrs. 6hrs.
Painting Interval Min 22hrs. 16hrs. 10hrs. 6hrs.Max 3 3 3 3
Pot Life 5hrs. 4hrs. 3hrs. 2hrs.
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum 5
degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 1.2 - 1.8Pa・s
Tip No. : (GRACO)623 Paint Output Pressuer: 14.7 - 17.7[MPa] Spray Speed : 60 - 80[cm/sec]
Thinner : BISCON QL THINNER, Thinning: 0 - 10 % by Volume
Preceding Coats : WELBOND, NZ PRIMER, EPICON ZINC RICH PRIMER, UMEGUARD PU-TU, etc.
Conditionof
Application
Subsequent Coats : -
Packaging Two pack product
Notes 1.The surface must be thoroughly cleaned by thinner wiping of fresh water washing to remove salt, dirt, oil, grease, chalking and impurities.2.Minimum coating intervals on the existing film are as follows. (Alkyd paint : more than 6 months, Chlorinated rubber paint : more than 12 months, Epoxy paint : more than 2 days)
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
UMEGUARD PU-TU(UG PU-TU)
Feb.2006
No. 6164
UMEGUARD PU-TU is based on epoxy polyurethane resin. It gives excellent physical properties such as adhesion, flexibility, toughness and abrasion resistance, etc. and chemical resistance to water and sea water. It has good adhesion to the existing paint surface. UMEGUARD PU-TU is suitable for repair of ships by simply surface preparation such as disc sanding or chipping, and for newbuilding ships by simply surface preparation such as brooming or hand brushing.
TECHNICAL DATA
Type Epoxy urethane resin paint, high build
Recommened
Use
Deck, Hatch cover, etc.
Mixing Ratio : Color :
Base : Hardener = 88 : 12 [by volume]Brown
Flash Point : Base = 6.0, Hardener = 2.0 [degC] Solid by volume : 69 (+-2) [volume %] VOC : 303 [g/L] Coverage(Theoretical): 0.145 - 0.29 [L/m
2
]
Information
Film Thickness : WET 145 - 290 [micron]DRY 100 - 200 [micron]
(D.F.T. 200micron) 5 oC 10 oC 20 oC 30 oC
Drying Time Surface Dry 50min. 45min. 35min. 30min.Hard Dry 22hrs. 16hrs. 10hrs. 6hrs.
Painting Interval Min 22hrs. 16hrs. 10hrs. 6hrs.Max 3 3 3 3
Pot Life 4hrs. 3hrs. 2hrs. 1hrs.
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum 5
degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : - 1.5Pa・s
Tip No. : (GRACO)619,621 Paint Output Pressuer: 14.7 - 17.7[MPa] Spray Speed : 60 - 80[cm/sec]
Thinner : BISCON QL THINNER, Thinning: 0 - 10 % by Volume
Preceding Coats : -
Conditionof
Application
Subsequent Coats : UMEGUARD PU
Packaging Two pack product
Notes 1.The surface must be thoroughly cleaned by thinner wiping of fresh water washing to remove salt, dirt, oil, grease, chalking and impurities.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
UMEGUARD SUPER H(UMEGUARD SUPER H)
Sep.2006
No. 6197
UMEGUARD Super H, is a high solid paint based on a combination of epoxy resin, special abrasive resistant agent and polyamide amine resin. It provides excellent abrasive resistance and fast cures to a hard paint film which have excellent anti-abrasion property.It is suitable for protection of cargo hold as a finish coat.
TECHNICAL DATA
Type High solid Epoxy/Polyamide amine coating
Recommened
Use
Cargo hold, Void space, Cofferedam, Engine room.Inside of accommodation space.
Mixing Ratio : Color :
Base : Hardener = 83 : 17 [by volume]Grey
Flash Point : Base = 17.5, Hardener = 24.5 [degC] Solid by volume : 75 (+-2) [volume %] VOC : 248 [g/L] Coverage(Theoretical): 0.133 - 0.2 [L/m
2
]
Information
Film Thickness : WET 133 - 200 [micron]DRY 100 - 150 [micron]
(D.F.T. 150micron) 15 oC 20 oC 30 oC
Drying Time Surface Dry 1hrs. 30mins. 20mins.Hard Dry 16hrs. 12hrs. 8hrs.
Painting Interval Min 16hrs. 12hrs. 8hrs.Max 10days 10days 10days
Pot Life 14hrs. 8hrs. 5hrs.
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum 15
degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 1.6 - 2.0 Pa・s
Tip No. : (GRACO)619,719 Paint Output Pressuer: 14.7 - 17.7[MPa] Spray Speed : 60 - 80[cm/sec]
Thinner : EPICON MARINE THINNER, Thinning: 0 - 5 % by Volume
Preceding Coats : UMEGUARD SUPER H PRIMER
Conditionof
Application
Subsequent Coats : -
Packaging Two pack product
Notes 1.In confined spaces such as tank insides, ventilation is required during application and curing to remove solvent vapours and promote curings.2.If there is a possibility that the painted surface will be in direct sunlight, the succeeding coat should be applied, as soon as possible after the minimum painting interval.3.Too much solvent results in reduced sag resistance and paint film property.4.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
UMEGUARD SUPER-H PRIMER(UG SH Pr)
May.2006
No. 6195
UMEGUARD SUPER-H PRIMER, is a exclusive epoxy primer for UMEGUARD SUPER-H, which gives excellent physical properties such as toughness, abrasion resistance and adhesion, etc., and has excellent resistance to dry hand cargo such as coal and iron-one.It is suitable for protection at cargo hold as a primer coat.
TECHNICAL DATA
Type Epoxy paint
Recommened
Use
Anti-corrosive paint for Cargo hold of the bulk carrier.
Mixing Ratio : Color :
Base : Hardener = 81 : 19 [by volume]Grey, Red brown
Flash Point : Base = 23.1, Hardener = 24.9 [degC] Solid by volume : 63 (+-2) [volume %] VOC : 401 [g/L] Coverage(Theoretical): 0.16 - 0.32 [L/m
2
]
Information
Film Thickness : WET 159 - 317 [micron]DRY 100 - 200 [micron]
(D.F.T. 200micron) 10 oC 20 oC 30 oC
Drying Time Surface Dry 5.5hrs. 4hrs. 2.5hrs.Hard Dry 18hrs. 10hrs. 8hrs.
Painting Interval Min 18hrs. 10hrs. 8hrs.Max * * *
Pot Life 14hrs. 7hrs. 4hrs.
Method of Application : Airless spray, Brush Weather : Temperature : Minimum 10
degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 1.6 - 2Pa・s
Tip No. : (GRACO)621,623 Paint Output Pressuer: 14.7 - 17.7[MPa] Spray Speed : 60 - 80[cm/sec]
Thinner : EPICON MARINE THINNER, BANNOH THINNERThinning: 0 - 15 % by Volume
Preceding Coats : CERABOND, etc.
Conditionof
Application
Subsequent Coats : UMEGUARD SUPER-H
Packaging Two pack product
Notes 1.* Kindly consult with CMP sales office.2. In confined spaces such as tank insides or low temperature condition, ventilation is required during application and curing to removed solvent vapours and promote curing.3.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
UMEGUARD SUPER-H PRIMER QD(UG SH Pr QD)
May.2006
No. 6196
UMEGUARD SUPER-H PRIMER QD, is a exclusive epoxy primer for UMEGUARD SUPER-H in winter season, which gives excellent physical properties such as toughness, abrasion resistance and adhesion, etc., and has excellent resistance to dry hand cargoes such as coal and iron-one. It is suitable for protection of cargo hold as a primer coat.
TECHNICAL DATA
Type Epoxy paint
Recommened
Use
Anti-corrosive paint cargo hold of the bulk carrier.
Mixing Ratio : Color :
Base : Hardener = 81 : 19 [by volume]Grey, Red brown
Flash Point : Base = 23.1, Hardener = 24.9 [degC] Solid by volume : 63 (+-2) [volume %] VOC : 394 [g/L] Coverage(Theoretical): 0.16 - 0.32 [L/m
2
]
Information
Film Thickness : WET 159 - 317 [micron]DRY 100 - 200 [micron]
(D.F.T. 200micron) 5 oC 10 oC 20 oC 30 oC
Drying Time Surface Dry 5hrs. 4.5hrs. 3hrs.Hard Dry 17hrs. 13hrs. 8hrs.
Painting Interval Min 17hrs. 13hrs. 8hrs.Max * * *
Pot Life 6hrs. 5hrs.
Method of Application : Airless spray, Brush Weather : Temperature : Minimum 5
degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 1.6 - 2Pa・s
Tip No. : (GRACO)621,623 Paint Output Pressuer: 14.7 - 17.7[MPa] Spray Speed : 60 - 80[cm/sec]
Thinner : EPICON MARINE THINNER, Thinning: 0 - 15 % by Volume
Preceding Coats : CERABOND, etc.
Conditionof
Application
Subsequent Coats : UMEGUARD SUPER-H
Packaging Two pack product
Notes 1.* Kindly consult with CMP sales office.2. In confined spaces such as tank insides or low temperature condition, ventilation is required during application and curing to removed solvent vapours and promote curing.3.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
UMEGUARD SX(UG SX)
Feb.2006
No. 6166
UMEGUARD SX, surface tolerant paint, is a epoxy type paint. It gives excellent physical properties such as adhesion, toughness and abrasion resistance, etc. and chemical resistance to water, salt water and crude oil.
TECHNICAL DATA
Type Surface tolerant anti-corrosive paint used as primer and topcoat
Recommened
Use
Cargo hold, Inside and outside of accommodation space, Deck,Void space, Cofferdam, Engine room, Pipe line, Other steel structures, etc.
Mixing Ratio : Color :
Base : Hardener = 85 : 15 [by volume]Grey, Black, White, Red brown
Flash Point : Base = 23.5, Hardener = 19.0 [degC] Solid by volume : 57 (+-2) [volume %] VOC : 435 [g/L] Coverage(Theoretical): 0.176 - 0.439 [L/m
2
]
Information
Film Thickness : WET 176 - 439 [micron]DRY 100 - 250 [micron]
(D.F.T. 250micron) 5 oC 10 oC 20 oC 30 oC
Drying Time Surface Dry 4.5hrs. 3.5hrs. 2.5hrs. 1.5hrs.Hard Dry 44hrs. 27hrs. 17hrs. 12hrs.
Painting Interval Min 44hrs. 27hrs. 17hrs. 12hrs.Max - - - -
Pot Life 24hrs. 14hrs. 8hrs. 5hrs.
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum 5
degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 1.5 - 2.0Pa・s
Tip No. : (GRACO)623 Paint Output Pressuer: 14.7 - 17.7[MPa] Spray Speed : 60 - 80[cm/sec]
Thinner : EPICON THINNER, Thinning: 0 - 5 % by Volume
Preceding Coats : WELBOND, CERABOND, NZ PRIMER, EPICON ZINC RICH PRIMER
Conditionof
Application
Subsequent Coats : EPICON MARINE FINISH HB,, ACRI 700,, etc.
Packaging Two pack product
Notes 1.In confined spaces such as tank insides, ventilation is required during application and curing to remove solvent vapours and promote curing.2.As nature of epoxy coatings UMEGURD SX can not avoid chalking and fading on UV exposure.3.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
UMEGUARD SX HS(UMEGUARD SX HS)
Feb.2006
No. 6193
UMEGUARD SX HS, surface tolerant paint, is a modified epoxy paint. It gives excellent physical properties such as adhesion, toughness and abrasion resistance.It has excellent resistance to sea water and cathodic protection.
TECHNICAL DATA
Type Modified anticorrosive epoxy paint
Recommened
Use
Anti-corrosive paint for ship's bottom ,Cargo hold, Inside and outside of accommodation space, Void space, Cofferdam, Engine room, Pipe line, Other steel structures, etc.For use at Maintenance and Repair.
Mixing Ratio : Color :
Base : Hardener = 74 : 26 [by volume]Grey, Black, Red brown, Green
Flash Point : Base = 17.5, Hardener = 24.5 [degC] Solid by volume : 72 (+-2) [volume %] VOC : 286 [g/L] Coverage(Theoretical): 0.139 - 0.278 [L/m
2
]
Information
Film Thickness : WET 139 - 278 [micron]DRY 100 - 200 [micron]
(D.F.T. 150micron) 5 oC 10 oC 20 oC 30 oC
Drying Time Surface Dry 7hrs. 3.5hrs. 1.5hrs.Hard Dry 28hrs. 17hrs. 12hrs.
Painting Interval Min 28hrs. 17hrs. 12hrs.Max 7days 7days 5days
Pot Life 5hrs. 3hrs. 1.5hrs.
Method of Application : Airless spray, Brush, Roller Weather : Temperature : Minimum 10
degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 1.5 - 2.0 Pa・s
Tip No. : (GRACO)623 Paint Output Pressuer: 14.7 - 17.7[MPa] Spray Speed : 60 - 80[cm/sec]
Thinner : EPICON MARINE THINNER, Thinning: 0 - 5 % by Volume
Preceding Coats : WELBOND, CERABOND, NZ PRIMER, EPICON ZINC RICH PRIMER
Conditionof
Application
Subsequent Coats : EPICON MARINE HB, UNY MARINE, etc.
Packaging Two pack product
Notes 1.In confined spaces , ventilation is required during application and curing to remove solvent vapours and promote curing.2.As nature of modified epoxy coatings UMEGURD SX HS can not avoid chalking and fading on UV exposure.3.If painting interval is exceeded,it may be necessary to roughen the surface.4.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
UMEGUARD SX QD(UG SX QD)
Feb.2006
No. 6135W
UMEGUARD SX QD, is a epoxy type paint. It gives excellent physical properties such as adhesion , toughness and abrasion resistance, etc. and chemical resistance to water, salt water and crude oil. In addition , it has excellent drying properties at low temperatures.
TECHNICAL DATA
Type Epoxy type paint
Recommened
Use
Cargo hold, Inside and outside of accomdation space, Void space, Cofferdam, Engine room, Pipe line, Other steel structures, etc.
Mixing Ratio : Color :
Base : Hardener = 85 : 15 [by volume]Grey, Black, White, Red brown
Flash Point : Base = 23.5, Hardener = 19.0 [degC] Solid by volume : 57 (+-2) [volume %] VOC : 435 [g/L] Coverage(Theoretical): 0.176 - 0.439 [L/m
2
]
Information
Film Thickness : WET 176 - 439 [micron]DRY 100 - 250 [micron]
(D.F.T. 250micron) -5 oC 0 oC 5 oC 10 oC 20 oC
Drying Time Surface Dry 8hrs. 5hrs. 2.5hrs. 2hrs. 1.5hrs.Hard Dry 40hrs. 33hrs. 20hrs. 16hrs. 14hrs.
Painting Interval Min 40hrs. 33hrs. 20hrs. 16hrs. 14hrs.Max - - - - -
Pot Life 20hrs. 12hrs. 6hrs.
Method of Application : Airless spray, Brush, Roller Weather : Temperature : -5 - 20
degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : 1.5 - 2.0Pa・s
Tip No. : (GRACO)623 Paint Output Pressuer: 14.7 - 17.7[MPa] Spray Speed : 60 - 80[cm/sec]
Thinner : BISCON THINNER, Thinning: 0 - 15 % by Volume
Preceding Coats : WELBOND, CERABOND, NZ PRIMER, EPICON ZINC RICH PRIMER
Conditionof
Application
Subsequent Coats : -
Packaging Two pack product
Notes 1. In confined spaces such as tank insides or low temperature condition, ventilation is required during application and curing to removed solvent vapours and promote curing.2.The temperature of the mixed base and hardener preferably should be above 10 degC otherwise extra solvent may be required to obtain appliaction viscosity.3.Too much solvent results in reduced sag resistance and paint film property.4.Application at temperatures down to -5 degC is possible but curing to hardeness takes longer and complete cure will be reached when temperature increases.5.Waiting time before the first cargo loading Temp. 5degC 10degC 20degC (Days) 25 16 10
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
6.VOC content data in this sheet is calculated from the formulation.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
UNY MARINE(UM)
Feb.2006
No. 5510A
UNY MARINE, based on polyurethane resin, has excellent gloss retention, durability and chemical resistance, etc. It is suitable for protection of outside of superstructure of steel ships.
TECHNICAL DATA
Type Polyurethane finish paint
Recommened
Use
Glossy finish coat on outside of superstructure, deck and fittings.
Mixing Ratio : Color :
Base : Hardener = 80 : 20 [by volume] White, As specified
Flash Point : Base = 23, Hardener = 30 [degC] Solid by volume : 44 (+-2) [volume %] VOC : 493 [g/L] Coverage(Theoretical): 0.068 - 0.113 [L/m
2
]
Information
Film Thickness : WET 113 [micron]DRY 50 [micron]
(D.F.T. 50micron) 5 oC 10 oC 20 oC 30 oC
Drying Time Surface Dry 50mins. 30mins. 20mins. 10mins.Hard Dry 12hrs. 8hrs. 6hrs. 4hrs.
Painting Interval Min 8hrs. 6hrs. 4hrs. 2hrs.Max * - - - -
Pot Life 24hrs. 20hrs. 16hrs. 8hrs.
Method of Application : Airless spray, Brush Weather : Temperature : Minimum 0
degC, Humidity : Maximum 85 %R.H. For Airless Spray : Viscosity : (Fc#4)25 - 35[sec]
Tip No. : (GRACO)515,615,715,813 Paint Output Pressuer: 11.7 - 14.7[MPa] Spray Speed : 80 - 100[cm/sec]
Thinner : UNY MARINE THINNER, Thinning: 5 - 15 % by Volume
Preceding Coats : BANNOH 500, BANNOH 200, EPICON MARINE UNDERCOAT M, etc.
Conditionof
Application
Subsequent Coats : -
Packaging Two pack product
Notes 1.* Please refer to the painting specifications.2.VOC content data in this sheet is calculated from the formulation.