Issue Date

January 2017

INSTALLATIONINSTRUCTIONS

Accessory Application Publication No.

MII

© 2017 Honda Motor Co., Ltd. - All Rights Reserved.

PARTS LIST

87949-MKF-D4001 of 5

Honda Dealer: Please give a copy of these instructions to your customer.

QUICK SHIFTERP/N 08U70-MKF-D40

TOOLS REQUIREDSocket (8 and 10 mm)RatchetOpen-end wrench (8 and 10 mm)Torque wrench

CBR1000RR/RA

No. Description Qty

(1) URL paper 1

(2) Gear change arm 1

(3) Change bar 1

(4) Stroke sensor 1

(5) 7 mm flange bolt 1

(6) 7 mm flange nut 1

(7) 6 mm nut (Left-hand threads) 1

(8) 6 mm nut 1

(9) Spindle plate 1

(1)

INSTALLATION CAUTION

• To prevent burns, allow the engine, exhaust system, radiator, etc. to cool before installing the accessory.

NOTE:• Take care not to damage the painted surfaces of the

motorcycle.• Disconnect the negative (-) cable from the battery

before installing this accessory.• The memories of the clock and calendar will be

erased when you disconnect the battery. After reconnecting the battery, refer to the motorcycle Owner’s Manual and reset the meter.

• After this accessory installation, check the lights (e.g. right/left turn signal lights and brake lights) for proper operation.

• Save all removed parts unless otherwise indicated.

• Illustration shows CBR1000RA type, other types are similar.

Item N·m kgf·m lbf·ft

6 mm nut 10 1.0 7

7 mm flange bolt and nut 12 1.2 9

TORQUE CHARTTighten all screws, bolts, and nuts to their specified torque values. Refer to the Service Manual for the torque values of the removed parts.

1. Refer to the Service Manual for the motorcycle, remove the motorcycle parts, and disconnect the negative (-) cable from the battery as shown.

NEGATIVE (-) CABLE

BOLT

BOLT

WASHERFRONT SEAT

(7)

(8)

(3)(4)

(6)

(2)

(5)

(9)

NEGATIVE (-) CABLE

2 of 5

2. Refer to the Service Manual for the motorcycle, remove the motorcycle parts.

3. Refer to the Service Manual for the motorcycle, remove the motorcycle parts.

4. Move the canister as shown.• Be careful not to damage the left crankcase

cover.

5. Assemble the stroke sensor and gear change arm as shown.

7 mm FLANGE BOLT

STROKE SENSOR

GEAR CHANGE ARM7 mm FLANGE NUT

BOLT

EVAP COVER

CLIP

NUT(Save)

ROD(Save)

ARM(Save)

STAY(Save)

BOLT

NUT(Save)

BOLT

BOLT

CANISTER

Move.

Protect.

6. Remove the dummy connector as shown.

MOTORCYCLE’S HARNESS AND HARNESS BOOT

DUMMY CONNECTOR(Save)

MOTORCYCLE’S WIRE TIE

3 of 5

10. Install the change bar as shown.• Adjust the quick shifter length to the specified

as shown.

7. Connect the stroke sensor connector as shown.

8. Secure the harness boot with the motorcycle’s wire tie as shown.

MOTORCYCLE’S HARNESS

STROKE SENSOR CONNECTOR

CLIP BANDInstall.

11. Install the motorcycle’s parts in the reverse order of removal.• Confirm that the harness is not caught or too

tight.• After installing the quick shifter, perform the

initialization.

9. Install the stroke sensor/gear change arm as shown.• Align the punch mark on the gearshift spindle

with the slit of the gear change arm.

SPINDLE PLATE

BOLT(Reuse)

BOLT(Reuse)

STROKE SENSOR/GEAR CHANGE ARM

6 mm NUT (Left-hand threads)Turn it fully seated.

Align.

MOTORCYCLE’S WIRE TIE(Reuse)

6 mm NUTTighten.

6 mm NUTTighten.

CHANGE BARTighten the nuts evenly.

265 mm

4 of 5

INITIALIZATION INSTRUCTIONS1. Open the rear seat and connect the SCS short

connector (070PZ-ZY30100).2. Turn the ignition switch ON with the engine stop

switch RUN, but does not start the engine.3. Push and hold the MODE and either SEL switch.

4. Select the QUICKSHIFTER and EQUIPMENT.

5. Set ON. (After removing the quick shifter, set OFF.)

8. Start the engine and let it idle.• Hold the neutral gear position.

SEL UP switch:move to the upper side menu item.

SEL DOWN switch:move to the lower side menu item.

MODE switch:select the menu item.

9. Wait until switched to the display shown.

10. Wait until switched to the display (initialization completion) shown.• I f the init ialization failure, restar t the

initialization again. • When you do not complete even af ter

repeating the initialization is to check the mounting state of the stroke sensor.

11. Turn the ignition switch OFF and remove the SCS short connector.

Initialization completion

Initialization failure

Push and hold the MODE and SEL switches.

6. Select the QUICKSHIFTER and INITIALIZE.

7. Initialization Ready

5 of 5

If you cannot shift up and down by operating the shift pedal during acceleration, a failure may occur. Refer to the Service Manual for the troubleshoot of the Quick Shifter.

NOTE:• For setting the UP LVL or DOWN LVL of the

Quick Shifter, refer to the Owner’s Manual.

OPERATING INSTRUCTIONSThis accessory enable the shift change without clutch operation when shifting up and down during acceleration. (Engine speed is more than 1,500 rpm on upshifting or more than the idle speed on downshifting).• If the gear position display is not normal, the shift

feeling may change.• When the shift change do not operate normally, the

shift change by clutch operation can be operated.