INSTALLATION INSTRUCTIONS - Bracketron, Inc....Part Number: CBM-100-01 INSTALLATION INSTRUCTIONS...

Part Number: CBM-100-01

062706-1

INSTALLATION INSTRUCTIONS

HONDA ACCORD (2003-2007)HONDA ACCORD HYBRID (2005-2007)

Fits United States Built Vehicles Only

NOTE: READ INSTRUCTIONS COMPLETELY BEFORE INSTALLING THIS BRACKETRON PHONE MOUNT.All instructions are written from the drivers seat position looking forward at the vehicle dash. We advise caution whenever your removing or handling plastic parts of a vehicles dash. WARNING: Unnecessary force or pressure can cause pieces to crack or break.

Start by applying the emergency brake. Place the transmission shift lever into the neutral position. Remove the trim bezel that surrounds the shift lever using the dash trim panel tool. In the left corner of the bezel start working the trim panel loose releasing six (6) clips. Carefully remove the bezel and place it in a safe place. Locate and remove the two screws that are directly in front of the shifter lever.

Locate and open the tray cover to the left of the power outlet. Locate and remove the screw at the bottom of the tray. Remove the tray by lifting it out and releas-ing two (2) clips toward the bottom. Locate and remove the two (2) screws that are underneath the tray. Using the dash trim tool, release three (3) clips that hold the power outlet assembly. Place the assembly in a safe place. Locate the dash bin above the power outlet. Remove the screws that are in the lower corners of the bin. Close the door and pull the bin out. Place the bin in a safe place. Locate and remove two (2) hex head screws that secure the lower section of the radio module. Set the screws aside.

Using the dash trim panel tool, remove the air vent that is above the radio. Care-fully insert the tool in the lower right corner of the air vent. Pull toward you to release the first clip. Perform this same action in the center of the vent and in the lower left corner of the vent for a total of three clips. Grasp the vent and carefully pivot it upward and out to release the top section of the vent. Set the vent aside. Locate and remove three (3) Phillips screws at the top of the radio. Set screws aside. Using the dash trim panel tool, locate and release three (3) clips at the bottom of the radio just below the large round knobs. Carefully grasp the radio and let it hang. Note: Do not disconnect the wire attached to the radio.

Insert the Bezel Mount in the upper right corner of the radio cavity. The Bezel Mount bottom edge should rest on a ledge inside the cavity. Use the supplied #8x3/4” self tapping screws and #2 Phillips screwdriver to secure the mount. Insert and tighten the first screw in the top hole to assist in the proper angle, then insert the remaining two (2) screws.

TOOLS NEEDED: Dash Trim Tool, (Part #SIT-104), 10mm socket and driver, #2 Phillips screwdriver.PARTS INCLUDED: One phone mount , Three (3) #8x3/4” self tapping screwsLOCATION OF MOUNT: To the right of the radio

Step 1.

Step 2.

Step 3.

Step 4.

Logo and part number will be right side up and readable when installed.

Carefully reinstall the dash in reverse order.

Install any Bracketron phone holder or Amps compatible device to your Bezel Mount.

Your Installation is complete.

Screws

Clips

Mount on Ledge

Alw

ays

chec

k ou

r web

site

for t

he m

ost u

pdat

ed m

odel

yea

r com

patib

ility

info

rmat

ion.

© Bracketron Inc, 2007 All rights reserved.The information in this document is subject to change without notice. Bracketron Inc. assumes no responsibility for any errors that may appear in this document nor do we assume any liability in connection with its use. This supersedes and voids all previous literature. Please contact the sales department for additional information.Bracketron Inc will not be responsible or liable for damage to vehicles in the installation and or removal of this Bracketron Inc mount.Bracketron Inc will not be liable for personal injuries or damage to property resulting from a motor vehicle accident and or improper installation of this Bracketron Inc mount.

Bracketron Inc. 5249 West 73rd Street, Suite G, Edina, MN 55439, Ph: 952-746-7775 Fax: 1-800-660-1784 Toll Free: 1-866-237-4443Web Address: www.bracketron.com



LINCOLN AVIATOR(2003-2005)

NOTE: READ INSTRUCTIONS COMPLETELY BEFORE INSTALLING THIS BRACKETRON PHONE MOUNT.All phone mount instructions are written from the driver’s seat position looking forward at the vehicle dash. We advise caution when-ever you are removing or handling plastic parts of a vehicle’s dash. WARNING: Unnecessary force or pressure can cause pieces to crack or break. Logo and part number will be right-side up and readable when installed.

Begin by removing the center console air vent module that is secured with four (4) clips. To do this, insert the Dash Panel Trim tool in the seam between the climate control and the air vents on the right side. The air vent module is just above the climate control. Carefully pull the tool backward to release the lower-right clip of the vent module. Perform this same action in the lower-left side releasing the left clip. Note: The two (2) top clips of the air vent module can be stubborn to loosen. You will need to release the bezel that surrounds the radio and extends up to the top of the dash just enough so the top clips of the air vent module will come loose. The radio bezel does not need to be fully removed, just its lower clips. Insert the hook tool in the lower-right corner of the radio and carefully pull back to release the clip. Perform same action in left corner. Carefully release the top clips of the air vent module. Disconnect the clock wiring and set the unit aside.

On the inside-right of the center console, locate a flat area just to the right of the exposed air vent and just below the radio bezel (See Picture). Place the Custom Bezel Mount in position. Insert one of the included self-tapping screws in the lower hole of the Custom Bezel Mount and tighten with Phillips screwdriver. With the one screw in place, pivot the Custom Bezel Mount to desired angle position. Insert the remaining screws and tighten.

Carefully reinstall the dash in reverse order. Install any Bracketron phone holder or AMPS compatible device to your Custom Bezel Mount.

Your Installation is complete.

TOOLS NEEDED: Dash Trim Tool, (Part #SIT-104), Hook Tool (Part #SIT-103), #2 Phillips screwdriver.PARTS INCLUDED: Three (3) #8x3/4” self tapping screwsLOCATION OF MOUNT: To the Right of the Air Vent

Step 1.

Step 2.

Step 3.

Clip Locations



062706-1A

lway

s ch

eck

our w

eb s

ite fo

r the

mos

t upd

ated

mod

el y

ear c

ompa

tibili

ty in

form

atio

n.



LEXUS LS430 (2001-2006) (with or w/o GPS) ES300 (2002-2005)



TOOLS NEEDED: # 2 Phillips screwdriver, clean cloth, 10mm socket and driver, 5/64” drill bit and drill, hook tool, marking pen.PARTS INCLUDED: One phone mount, instructions, three (3) #8 x 1/2 “ screws.LOCATION OF MOUNT: To the Right of the Radio

Step 1.

Step 2.

Step 3.

Caution: Apply a clean, protective cloth over the gearshift lever before the start of this installation. Be extremely careful while working on this vehicle, the wood grain panels may scratch very easily!

Start installation by removing the lower panel that holds the seat heater controls. Carefully insert the hook tool behind the panel and gently pull it towards you, to release the two (2) Heater clips, one (1) on the left and right side. Unplug the wiring connector on the back and set this panel aside. Locate the three (3) Phillips screws exposed by removing the lower panel and remove them. Open the panel that covers the CD player (pushing on it). Carefully insert the hook tool in the left and then right corner to release the two (2) clips. When the clips are released, the panel should slide off. Unhook the wiring harness on the back and set this panel aside.

The removal of the radio. Caution: DO NOT disconnect any wires to the radio! Remove the two (2) 10mm bolts at the base of the radio, one on the left and one on the right. Place your hand under the radio while pulling it toward yourself. There are two (2) clips, one in the middle left and one in the middle right that should release as you pull the radio out of its space. Set the radio aside.

Place the Custom Bezel Mount against the dash pad. The top of the Custom Bezel Mount will touch the bottom of the air vents or the climate control panel (this could vary if the car has GPS or not). Using the Bezel Mount as a template, mark the location of the three (3) screw holes. Using a 5/64” drill bit, drill three (3) pilot holes at the marked loca-tions. Caution: Do Not drill holes deeper than 1/4”. Align the Custom Bezel Mount over the drilled pilot holes and insert the three (3) # 8 x 1/2” screws and tighten.

Re-assemble the dash in reverse order securing all screws and clips. Install any Bracketron phone holder or Amps compatible device to your Custom Bezel Mount.

Your installation is complete.



062706-1A

lway

s ch

eck

our w

eb s

ite fo

r the

mos

t upd

ated

mod

el y

ear c

ompa

tibili

ty in

form

atio

n.



LEXUS ES300 (2002-2005) (with or w/o GPS)(See reverse side for LEXUS LS430 (2001-2006)


Caution: Place a clean, cloth over the gear shift lever At the start of this installation. Use caution while working on this vehicle, wood grain panels scratch very easily!

Set the parking brake and put the gear shift into neutral. Using the hook tool, remove the gear shift bezel by inserting the tool behind the lower left corner of the bezel, pull up gently, until releasing the retainer clip. Work the hook tool from back to front until all eight (8) clips are released. Lift the trim bezel over the gearshift and set it to the side. Do not discon-nect any wiring harnesses from the bezel. .

Remove the climate control module from the dash. The climate control module is fastened with five (5) clips, one in each corner and one at the top and center of the climate control module. Insert the hook tool behind the lower left corner of the climate control module and pull towards you, releasing a clip. The clips are usually very tight, so they will not release as easily as the clips on the bezel trim did. Work the hook tool around the climate control module, pulling towards yourself until all clips are released. Pull the climate control out of its space and set aside. DO NOT disconnect the wiring harness to the climate control module.

Place the Bezel Mount against the dash pad as shown in Photo. The top of the Bezel Mount will touch the bottom of the Radio module. Using the Bezel Mount as a template, mark the location of the three (3) screw mounting holes. Drill three (3) pilot holes at the marks using a 5/64” drill bit and drill. Caution: The holes should be drill no deeper than 1/4”. Posi-tion the Bezel Mount over the pilot holes and insert the three (3) # 8 x 1/2” screws and tighten.

Re-assemble the dash in reverse order securing all screws and clips. Put the gearshift into park and release the parking break. Install any Bracketron phone holder or Amps compatible device to your Bezel Mount.

Your installation is complete


TOOLS NEEDED: Hook tool, # 2 Phillips screwdriver, clean cloth, 5/64” drill bit, drill and marking pen.PARTS INCLUDED: One phone mount, instructions, three (3) #8 x 1/2” screws.LOCATION OF MOUNT: To the right of Climate Control.

Step 1.

Step 2.

Step 3.



062706-1A

lway

s ch

eck

our w

eb s

ite fo

r the

mos

t upd

ated

mod

el y

ear c

ompa

tibili

ty in

form

atio

n.



TOYOTA CAMRY(2002- 2006)

NOTE: READ INSTRUCTIONS COMPLETELY BEFORE INSTALLING THIS BRACKETRON PHONE MOUNT.All instructions are written from the driver’s seat position looking forward at the vehicle dash. We advise caution whenever you are removing or handling plastic parts of a vehicle’s dash. WARNING: Unnecessary force or pressure can cause pieces to crack or break.

Start by inserting the Dash Trim Panel Tool in the seam between the climate control and the radio bezel on the right side. Gently pull out the lower climate control releasing a retainer clip. Continue working the climate control loose releasing three more clips. Note: There are two (2) retainer clips on both the left and right sides of the climate control for a total of four (4) clips. Let the climate control hang to the left.

Insert the Dash Trim Panel Tool behind the bezel surrounding the radio in the upper-right corner. Carefully pull back to release top-right clip. Do this in all four corners of the bezel releasing four clips, two (2) on the top and two (2) on the bottom of the bezel. Once the radio bezel is loose, prop it up onto the top of the dash to keep it out of your way. There is no need to disconnect the wiring.

Locate a small piece of dash pad just to the right of the two retaining clip holes for the climate control and radio bezel on the right side of the cavity. Using your Sharp Razor Blade, Carefully shave this pad off cleanly. Note: See the first picture. Place the Bezel Mount in the cavity just above the seam as shown in the middle picture. Mark two (2) spots for pilot holes avoiding the top hole in the Bezel Mount. Remove the Custom Bezel Mount and carefully drill two (2) pilot holes making sure to drill into the solid plastic behind the thick dash pad. Caution: Make sure to be careful when drilling pilot holes. The dash pad can tear and twist easily. Use extreme caution when performing this step. Place the Custom Bezel Mount over the two pilot holes and insert the to two provided screws and tighten a Phillips Screwdriver.

Carefully reinstall the dash in reverse order. Install any Bracketron phone holder or AMPS compatible device to your Custom Bezel Mount. Your installation is complete.

TOOLS NEEDED: Dash Trim Tool, (Part #SIT-104), #2 Phillips Screwdriver, marking pen, 5/64” drill bit and drill, sharp razor blade utility knife.PARTS INCLUDED: Two (2) #8x3/4” self tapping screwsLOCATION OF MOUNT: To the right of the radio.

Step 1.

Step 2.

Step 3.

Remove Dash Pad

Place Above Seam

Logo and part number will be right-side up and readable when installed.



062706-1A

lway

s ch

eck

our w

eb s

ite fo

r the

mos

t upd

ated

mod

el y

ear c

ompa

tibili

ty in

form

atio

n.



SAAB 9.5 SEDAN (1999-2005)SAAB 9.5 WAGON (1999-2005)


Begin installation by inserting the two DIN tools (SIT-101) into the four holes in the face of the radio. ou will here and feel a click when they are inserted all the way. Gently, pull the radio out of the cavity by applying outward pressure to the DIN tools. Set the radio aside careully.

Use the Dash Trim Tool (SIT-104) and gently insert the tool to the right of the climate control. Pry slightly to release two (2) small plastic clips from each side of the radio. Do not disconnect the wires from the climate con-trol. Place climate control aside on a cloth or another soft surface.

Locate a spot to the right of the climate control cavity to place the Custom Bezel Mount. Note: Line up the Custom Bezel Mount towards the bottom of the cavity to allow room for the radio to slide back into place correctly. With the Custom Bezel Mount in the desired location, mark two (2) hole locations. Note: Use the bottom two holes and not the top hole.

Drill two (2) pilot holes at the marks using a 5/64” drill bit and drill. Cau-tion: The holes should be drill no deeper than 1/4”. Position the Custom Bezel Mount over the pilot holes and insert two (2) # 8 x 1/2” screws and tighten.

Re-assemble the dash in reverse order securing all screws and clips. Put the gearshift into park and release the parking break. Install any Bracketron phone holder or Amps compatible device to your Custom Bezel Mount.

Your installation is complete

Logo and part number will be right side up and readable when installed.TOOLS NEEDED: Ford DIN Tool (SIT-101), Dash Trim Tool (SIT-104) # 2 Phillips Screwdriver, 5/64” drill bit, drill and marking pen.PARTS INCLUDED: One CBM, instructions, Two (2) #8 x 1/2” screws.LOCATION OF MOUNT: To the right of Climate Control.

Step 1.

Step 2.

Step 3.



062806-1A

lway

s ch

eck

our w

eb s

ite fo

r the

mos

t upd

ated

mod

el y

ear c

ompa

tibili

ty in

form

atio

n.

Install Mount Here

Step 4.

Step 5.

PARTS INCLUDED:

1 - Ultra Slim Swivel1 - AMPs Adapter Plate4 - M4 x 10 Hex Head Screws4 - M4 x 10 Pan Head Screws4 - M4 x 12 Pan Head Screws4 - M4 Hex Head Nuts4 - M4 Nylon Locking Nuts4 - M4 Star Washers1 - Full Color Instruction Sheet

TOOLS NEEDED: One 9/32” open end wrench, one #2 Phillips Screwdriver.

LOCATION: Attach to any AMPs compat-ible mounting device.

Part Number: PHS-203


ULTRA SLIM SWIVEL

Note: The swivel can be installed before or after the mount is installed in the vehicle.Attach the Ultra Slim Swivel to a Bracketron Custom Bezel Mount or other AMPs mounting device by inserting the M4x10 Pan Head screws through the holes on the back half of the swivel. Align the screws up with the holes on the mount. Attach the M4 Nylon Locking Nuts only finger tight. Rotate the front half of the swivel to gain access to the M4x10 Pan Head screws. (See Top Left Picture) Tighten all 4 screws with a #2 Phillips screwdriver and 9/32” open end wrench. Tighten the center screw to adjust the desired tension of the swivel. (See Top Right Picture)

Step 1.

Step 2.

Rotate

Adjust Hold Tension

Step 3.

NOTE: PLEASE READ INSTRUCTIONS COMPLETELY BEFORE INSTALL-ING THIS BRACKETRON MOBILE SOLUTION. This Professional Swivel Mount Solution is designed for Satellite Radio Car Kits that require extra clearance to accommodate their plug & play connections when mounted to a Custom Bezel Mount or any other AMPs compatible mounting device. The Ultra Slim Swivel is compact with a low profile and is designed to provide adjustability to devices such as Satellite Radio Receivers, GPS monitors or Mobile Phones. The Ultra Slim Swivel angles your device for better viewing, tilting approximately 15° in all directions and swivels 360° degrees for maximum adjustability. All mount-ing hardware is included in the kit along with our AMPs adapter plate to attach devices that support T- Notch mounting.

Attach the AMPs T- Notch Adapter to the front half of the swivel using the M4x12 Pan Head screws. Attach the M4 Star Washers and M4 Hex Nuts to the screws and tighten the plate down with the #2 screwdriver and 9/32” open end wrench.Slide your device onto the T- notch Adapter plate to secure it to the swivel.

For T- Notch Devices

Attach Device

Attach your AMPs device using the M4x10 Hex Head screws and M4 Star Wash-ers. Align the holes on the device with the holes on the front half of the swivel. Slide the Star Washers onto the Hex Head screws. Insert the screws through the swivel and into your device only finger tight. Tighten down the device with the 9/32” open end wrench. Your device is now secure to the swivel.

For AMPs Devices with Inserts



062706-1A

lway

s ch

eck

our w

eb s

ite fo

r the

mos

t upd

ated

mod

el y

ear c

ompa

tibili

ty in

form

atio

n.

INSTALLATION INSTRUCTIONS - Bracketron, Inc....Part Number: CBM-100-01 INSTALLATION INSTRUCTIONS...

Documents

Transcript of INSTALLATION INSTRUCTIONS - Bracketron, Inc....Part Number: CBM-100-01 INSTALLATION INSTRUCTIONS...