IGGY-MADI Quick Start Guide - Ross Video
1
IGGY-MADI Installation © 2019 Ross Video Limited. Ross® and any related marks are trademarks or registered trademarks of Ross Video Limited. All other trademarks are the property of their respective companies. PATENTS ISSUED and PENDING. All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, mechanical, photocopying, recording or otherwise, without the prior written permission of Ross Video. While every precaution has been taken in the preparation of this document, Ross Video assumes no responsibility for errors or omissions. Neither is any liability assumed for damages resulting from the use of the information contained herein. 1000DR-806-01 Printed in Canada. CAUTION Before you set up and operate your IGGY-MADI see the “Important Regulatory and Safety Notices” that shipped with your unit. It is also recommended to refer to the IGGY-MADI User Guide. The IGGY-MADI User Guide is available for download from our website. BOTTOM OF MODULE TOP OF MODULE Mounting via Tie-wraps Refer to the guide that shipped with your install kit for additional details. Assigning the IP Address(es) Note: Press the Reset button to reset the IGGY-MADI, including the IP Address, to the factory default settings. This button is located beside the PWR/STAT LED. Note: To assign an IP address to an IGGY-MADI, DashBoard must run on a computer with a physical wired Ethernet connection and configured with an IP address in the same range as the default address of the IGGY-MADI (192.168.0.100). DC Power Connection CAUTION Ensure to connect the DC Power cord of the power supply to the PWR port on the IGGY-MADI chassis before connecting the power supply to the power source. WARNING The power supply connector of the IGGY-MADI power supply module must be fully inserted into the IGGY-MADI PWR port and the locking collar fully secured before use. Failure to do so may damage the PWR port on the IGGY-MADI chassis. Tally-GPIO Cabling (Optional) MADI Cabling Reference Cabling (Optional) REF IN REF OUT Network Cabling To Facility Network To Network Source 2 To Network Source 1 To Power Source MADI REF IN DIP Switch 3 5 7 9 11 13 25 23 21 19 17 15 12 10 8 6 4 14 16 18 20 22 24 1 2 GPIO PINs GPIO 1 GPIO 2 GPIO 3 GPIO 4 GPIO 5 GPIO 6 GPIO 7 GPIO 8 Pin 7 Pin 20 Pin 8 Pin 21 Pin 9 Pin 22 Pin 10 Pin 23 TALLY PINs TALLY 1A TALLY 1B TALLY 2A TALLY 2B TALLY 3A TALLY 3B TALLY 4A TALLY 4B Pin 1 Pin 14 Pin 2 Pin 15 Pin 3 Pin 16 Pin 4 Pin 17 CAUTION The NET 1 Port provides PoE (power over ethernet). TALLY/GPIO Port — Pinouts To assign the IP Address(es) to the IGGY-MADI 1. Ensure that you are running DashBoard software version 8.4.0 or higher. Note: The DashBoard software is available at: https://www.rossvideo.com/support/software-downloads/dashboard/ 2. Launch DashBoard by double-clicking its icon on your computer desktop. 3. Select File > Show Walkabout. 4. Click Refresh. 5. Locate the IGGY-MADI entries in the Walkabout table. There is a table entry for each IGGY-MADI Port (CTRL, NET 1, and NET 2). 6. Use the Address field for each Port to specify the new IP Address(es) supplied by your IT Department for this device. 7. Ensure the other fields in the table are set to match your network requirements. 8. Click Reboot in the row of the Walkabout table for the IGGY-MADI. 9. Manually add the IGGY-MADI to the Tree View in DashBoard as outlined in the IGGY-MADI User Guide. Have a question? Call our free, 24-hour technical support hotline to speak with a live product specialist located right here in our facility. Tel: (+1) 613 • 652 • 4886 Email: [email protected]
Transcript of IGGY-MADI Quick Start Guide - Ross Video
IGGY-MADI Installation
© 2019 Ross Video Limited. Ross® and any related marks are trademarks or registered trademarks of Ross Video Limited. All other trademarks are the property of their respective companies. PATENTS ISSUED and PENDING. All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, mechanical, photocopying, recording or otherwise, without the prior written permission of Ross Video. While every precaution has been taken in the preparation of this document, Ross Video assumes no responsibility for errors or omissions. Neither is any liability assumed for damages resulting from the use of the information contained herein.
1000DR-806-01Printed in Canada.
CAUTION
Before you set up and operate your IGGY-MADI see the “Important Regulatory andSafety Notices” that shipped with your unit. It is also recommended to refer to theIGGY-MADI User Guide. The IGGY-MADI User Guide is available for downloadfrom our website.
BOTTOM OF MODULE
TOP OF MODULE
Mounting via Tie-wraps
Refer to the guide that shipped with your install kit for additional details.
Assigning the IP Address(es)
Note: Press the Reset button to reset the IGGY-MADI, including the IP Address, to the factory default settings. This button is located beside the PWR/STAT LED.
Note: To assign an IP address to an IGGY-MADI, DashBoard must run on a computer with a physical wired Ethernet connection and configured with an IP address in the same range as the default address of the IGGY-MADI (192.168.0.100).
DC Power Connection
CAUTION
Ensure to connect the DC Power cord of the power supply to the PWR port on the IGGY-MADI chassis before connecting the power supply to the power source.
WARNING
The power supply connector of the IGGY-MADI power supply module must be fully inserted into the IGGY-MADI PWR port and the locking collar fully secured before use. Failure to do so may damage the PWR port on the IGGY-MADI chassis.
Tally-GPIO Cabling (Optional)
MADI Cabling
Reference Cabling (Optional)
REF IN
REF OUT
Network Cabling
ToFacility Network
To NetworkSource 2
To NetworkSource 1
ToPowerSource
MADI
REF IN DIP Switch
3579111325 23 21 19 17 15
12 10 8 6 4141618202224
12
GPIO PINsGPIO 1GPIO 2GPIO 3GPIO 4GPIO 5GPIO 6GPIO 7GPIO 8
Pin 7Pin 20Pin 8Pin 21Pin 9Pin 22Pin 10Pin 23
TALLY PINsTALLY 1ATALLY 1BTALLY 2ATALLY 2BTALLY 3ATALLY 3BTALLY 4ATALLY 4B
Pin 1Pin 14Pin 2Pin 15Pin 3Pin 16Pin 4Pin 17CAUTION
The NET 1 Port provides PoE (power over ethernet).TALLY/GPIO Port — Pinouts
To assign the IP Address(es) to the IGGY-MADI1. Ensure that you are running DashBoard software version 8.4.0 or higher. Note: The DashBoard software is available at: https://www.rossvideo.com/support/software-downloads/dashboard/2. Launch DashBoard by double-clicking its icon on your computer desktop.3. Select File > Show Walkabout.4. Click Refresh.5. Locate the IGGY-MADI entries in the Walkabout table. There is a table entry for each IGGY-MADI Port (CTRL, NET 1, and NET 2).6. Use the Address field for each Port to specify the new IP Address(es) supplied by your IT Department for this device.7. Ensure the other fields in the table are set to match your network requirements. 8. Click Reboot in the row of the Walkabout table for the IGGY-MADI.9. Manually add the IGGY-MADI to the Tree View in DashBoard as outlined in the IGGY-MADI User Guide.
Have a question? Call our free, 24-hour technical support hotline to speak with a live product specialist located right here in our facility. Tel: (+1) 613 • 652 • 4886Email: [email protected]
