HYDROPONICSGARDEN KIT Setup Guide

Important Safety Instructions

How to Raise and Lower the Lampshade

Operation procedure

Included in Package

1. To reduce the risk of electric shock, do not change the plug in any way.2. Always unplug the garden kit from electrical outlet before cleaning water

tank or change water pump.3. Never operate garden kit if it has a damaged cord or plug, if it is not working

properly, if it has been dropped and damaged, or if it has been dropped inwater. If any of these conditions occur/exist, contact email:support@idooworld.com

4. Keep cord away from heated surfaces.5. This product is intended for household and residential use only. Do not use

outdoors.6. Do not allow water to contact hot LED Grow Lights.7. Do not place or submerge electrical outlet, cord, plug, or Lampshade in water

or other liquid to clean it.8. To prevent any damage to the machine, make sure no electric part is directly

submerged to water. If any water is spilled or scattered over any electric part, thoroughly dry all cables and any electricity- related parts.

9. This appliance is not intended for use by persons (including children) withreduced physical, sensory or mental capabilities, or lack of experience andknowledge, unless they have been given supervision or instruction concern-

ing use of appliance by a person responsible for their safety. Children should be supervised to ensure they do not play with the appliance.10. The operation of the machine requires 4-5 liters of water in the water tank,

otherwise appear "Beep" sound, and shorten the life of water pump.

1. Plug Adapter2. Sponges x 143. Basket Kit x 7

4. A solid nutrient5. B solid nutrient6. Rod x 14

To raise the Lampshade, press one hand around the bottom of the Lamp-shade and grasp the upper part of the Light Post with your other hand. Push up to raise the Lampshade.To lower the Lampshade, press down the Lampshade with one hand.Tips: When planting a new seed pod kit, the Lampshade should be set to the lowest possible position.

Step 1: Add WaterTake out the lid of the water tank.Use tap water or bottled distilled water. Do not use well water which may interfere with our nutrients, or softened water, as it contains levels of sodium usually harmful to plants. The 'Beep' sound reminder alert will appear when the water level is low.For best results, keep the water level between 4.5 liters and 5 liters.

Garden Kit

5 61 2 43

Notice: Please choose the right seeds which can totally growing under the rod high ( 15.75 inches ).

Light panel assembly

Max Height: 15.75 inches

Extendable rod

Basket container

Rubber plug at the filling nozzle

Water tank top cover

Water tank

Power pack

Timing: 14h-on-and-10h-off-cycle 12h-on-and-12h-off-cycle 16h-on-and-8h-off-cycleSize: 15.83 x 7.01 x 9.65 inWeight: 4.6 lbs

Specifications

Input: 24V 1ARated Voltage: 24VRated Power: 24WNoise: <40dBTemperature: 59℉- 86℉

01

Enjoy: Switch Light Mode by pressing 1 second.

Cycle Timing: Illuminate 12 hours/Day.

Step 2: Add NutrientsFill A nutrient bottle with room temperature tap water or bottled distilled water, shaking until well mixed.Fill B nutrient bottle with room temperature tap water or bottled distilled water, shaking until well mixed.Add 25 milliliters A solution and 25 milliliter B solution when adding 5-liter water to the tank.

Note: Too much nutrient may be harmful to your plants.Nutrient Feeding Tip: Always top off water level when adding Liquid Nutrients. 1-Liter water needs to add into 5 milliliters A solution and 5 milliliter B solution.For best results, top off the water level in your garden regularly.Do not use well water or softened water. Most well water contains a high amount of dissolved solids that upset the balance of our nutrients, and softened water adds sodium. This can result in plants suddenly browning, or just not growing well.Nutrient particles have a storage life of 2 years in unopened bottles if stored at the ambient temperature without exposure to sunlight.Well-mixed nutrient solutions have storage lives of 5 months if stored without exposure to sunlight.

Control Panel Settings

Step 3: Plug-InDo not plug the adapter when no water in tank.You will hear a "Beep" sound after plugging the adapter, indicating that light panel can be controlled. If you hear no sound, pull out the panel port, and insert tightly again until hearing "Beep" sound.The water pump runs after plug the adapter 1 mins (5 minutes on, 30 minutes off). If the pump runs immediately, pull out the panel port and insert it tightly again.

Power/Normal: Turn on the LED light by pressing 1 second and then the garden kit go into Normal Mode.Pressing and hold for 3 seconds, the light is forced to be turned off and then go into “off state” in Normal Mode. Cycle Timing: Illuminate 14 hours/Day (Tips: When you turn on the light at the 8:00 am, the light will turn on at the 8:00 am next every day automatically.)

Grow: Switch Light Mode by pressing 1 second. Cycle Timing: Illuminate 16 hours/Day. Pump Switch: Pressing and hold for 3 seconds, switch pump mode.Cycle System of Pump: 12 hours - no pump12 hours - a repeating cycle of 5 minutes on, 30minutes off.

Step 4: Add Seed Sponges & Basket KitsThe garden kit does not include the seed.Choose the seed of a well-known brand at local.Add 3-4 seeds to per sponges to improve germination rate.Some seeds germinate in 2-7 days. Please be patient. Choose one seedling when the seeds grow into seedlings. More seedling probably results in poor growth due to insufficient nutrients.

Place Your GardenOn a sturdy, water-tolerant surface.In a 59°F-86°F (15-30°C) environment (optimal).Beyond the reach of children or pets.Away from direct sources of heat ( stove, furnace vents, e.g.,) or cold ( window drafts, A/C vents, e.g.,).Indoor Garden Kit does not need additional light or a sunny window. In fact, too much direct sunlight can overheat your plants.

The System has a work clock that will automatically start to work in a 24h cycle upon proper connection of the machine to the municipal power supply; at the same time on each subsequent day, the system will automatically start and the LED will automatically turn on regardless of the mode setting.1. If you change the mode when the LED light is on, the cycle will take into account the time spent in the mode you changed from. a. For example, if the machine is in Normal mode (light on for 14 hours, off for 10 hours) and the light has been on for 13 hours and you change it to Enjoy mode (on for 12 hours, off for 12 hours), the light will immediately switch off for 12 hours as it enters the cycle for Enjoy mode. b. If the machine is in Normal mode (light on for 14 hours, off for 10 hours) and the light has been on for 10 hours in Normal mode and you switch it to Grow mode (light on for 16 hours, off for 8 hours), the light will continue to be on for 6 hours. After that, it will turn off for 8 hours as it enters the Grow mode cycle. * If you press and hold the button of the power for 3s when the machine is in Normal mode, the LED light will be off for 10hr immediately and run into the cycle of the Normal mode again.2. When the LED light is off, press and hold the Power/Normal button for 3s, after you hear ‘Beep’ two times, the light mode will run into the cycle of Normal mode (light on for 14 hours, off for 10 hours) immediately. Just before your normal bedtime, press the Power/Normal button for 3 seconds. This will tell the garden to start the 10-hour “lights off” cycle and you can sleep through the night. The lights will come back on 10 hours later and follow the same timing each day.”

LED Light Mode Switch:

02

LightsPlants love light! Always keep your Grow Lights as close to your plants as possible. Plants should be 1-2 inches below Lights.Always check to see if you can prune plants instead of raising Grow Lights. After pruning, lower your lights back down to within 1-2 inches of plants if possible.

PollinatingBecause most people don’t have bees in their home, you will need to start pollinating our fruiting plants (tomatoes, peppers, etc.) once they begin to flower approxiately 4 – 6 weeks after planting). To pollinate, use one or more of the following methods: Place an open hand inside plant branches and gently move your hand back and forth to shake the plant and spread the pollen.Place a fan near your plants and the moving air will pollinate your plants.

HarvestingGarden kit works best with a harvesting method called “cut and come again.” Simply put, you enjoy frequent small harvests and then watch as the plants rapidly regrow - ready for harvest again and again. Enjoy frequent, smaller harvests for the first month or two until plants mature and larger harvests are available.Harvest often to maintain a healthy garden, but never take more than 1/3 of each individual plant at a time.For Salad Greens, cut the top 2 inches off the entire garden, or harvest large leaves individually by cutting off at the base of the plant.

Cleaning pumpClean the cotton of the water pump at least once a month. You can take out the cotton from the pump to wash, and then replace it back.Do NOT plug the adapter when the water tank is no water, it will shorten the life of the pump.

Important Note: After the plants bloom, change the water once a week to ensure that the potassium content is sufficient.

An Important Note About Lights

GerminationCheck the seed information regarding optimal temperature and days to germinate. Plant 3-4 seeds per sponge. Some seeds germinate in 2-7 days or more. Many factors impact germination.

The basket lid help regulate moisture and temperature for optimal germination. Leave them on until plants are nearly touching the lid, then take it off.

Large plants like Tomatoes and Peppers plant fewer than 7 pods to make room for the large plant size. Leave space between seed pods to allow room for each to spread out.

However, plants are impacted by temperature. Cold weather plants like Salad Greens germinate better in cooler weather. Heat lovers like Tomatoes and Peppers will germinate faster in warmer temperatures (above 70 degrees F). Since they may take a bit more time, your seeds will germinate.

PruningCheck the seed information regarding optimal temperature and days to Lower your plants, don’t raise your lights! You will achieve more compact, beautiful growth and bigger harvests if you prune plants to keep the lights closer to all plants.

Fast-growing plants (like Basil) make gardeners want to raise the lampshade too soon. Resist! Pruning the plant just above a new leaf set (Diagram A) and leaving the lights down low will ensure that slow-growing plants in your garden get all the light they need to flourish.

Prune often to maintain a healthy garden, but never take more than 1/3 of each individual plant at a time.

Plants compete for light. Left untended, more aggressive growers can actually block enough light to suppress growth of their slower-growing neighbors, and eventually they can die off due to lack of light. Spreading leaves must be trimmed (Diagram B) to make sure that slow growers get enough light to thrive and produce big yields.

TransplantOnly when you see rhizome around the sponge, then you can transplant. Split the sponge to take one seedling out and move it to other pot.Put the sponge back, only keep one seedling in the sponge in order to get sufficient nutrition.

Once you choose one light mode to plant, the light will turn on and off automatically to provide your plants with “sunlight”, so you do NOT need to intervene when to turn on the light. If the light NEVER turns on, pull out the panel port, and then insert it into tightly. Because the garden kit has a layer of soft rubber to prevent water from seeping into the electrical outlet, which results in the poor connection.

An Important Note About Pump

Gardening Tips for Maximum Harvests

Pump will run after plug the adapter 1 minute. Pump go into a cycle of turn on 5 minutes, turn off 30 minutes.Insert the panel port tightly again if pump runs immediately.Pump never turn on, please contact Email - support@idooworld.com

Too High

Cut Here

StarterLeavesDiagram A Diagram B

Finally, pruning = harvesting. Each time you prune you get to enjoy fresh herbs in a salad, soup on pizza or a sandwich. And, a full, bushy garden looks much better than one giant, spindly plant surrounded by straggly, light starved neighbors. Pruning also releases a wonderful scent. So prune!

03

Warranty (1-Year Period)

Customer Service

FCC Statement

FCC Statement NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:• Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help with the supplied fastener. DO NOT hang the unit by the power cord.

1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation.

The manufacturer's warranty is void under the following circumstances but not limited to:• Improper or inadequate maintenance or modification.• Accident, misuse, abuse, contamination, or other external causes.• The use of unspecified adapter and accessories.• Loss or damage in transit.• Damages that occurs as a result of one's failure to follow the instructions.• This warranty does not apply to expendable or consumable parts and does not extend to any product from which the serial number has been removed.

We have an award-winning warranty, exchange, and customer service team that guarantees hassle-free solutions to any issue you might have within the 24 business hours.

Tel: 1-(714)-714-2984Monday-Friday: 9:00-16:30 PST

Email: support@idooworld.com

Web: https://idooworld.com

MADE IN CHINA

JOICOM CORPORATION 165 E. Freedom Ave., Anaheim,CA 92801

Shenzhen Runfeng Digital Technology Co., LTDChuanghui Building, Intersection of Banxuegang Boulevard and Yongxiang Road, Bantian Subdistrict, Longgang District, Shenzhen, Guangdong, China

1. How to clean the water pump? Step 1. Turn the power off Step 2. Remove the extendable rod and the top cover of the water tank. Step 3. Take out the sponge in front of the water pump and rinse it with water ONL Any washing liquid will harm the nutrition balance. (If it is very dirty, please rinse the water pump all together ) Step 4. Install those back and restart the machine.

For more details, please follow the steps in the video, link: https://youtu.be/4DqcmAUNtNg

By the way, if you need to replace the water pump, please kindly follow the steps in another video, link: https://youtu.be/7wNsZYUN-1A

2. Why do only a few of the plants grow and once grown, they quickly wither? a. The seeds you purchase make a difference. For best results, purchase seeds from reliable manufacturers and avoid purchasing seeds that are not suitable for water hydroponic devices. b. Ensure you are using the correct proportion of nutrient solution to water, LED l ight distance from the plants and temperature as stated in the user guide.3. Why does the pump start with noise? a. Regarding the problem, please switch the water pump mode to try again. b. Clean the water pump as stated in the user guide.

4. The light is too dazzling, what should I do? a. Please switch the light mode from ‘Grow mode’ or ‘Enjoy mode’ to ‘Normal mode’.

5. Can sponges be reused? It's reusable if pull out the stem of a plant, but we don’t recommend to do so as it’s not as good as the first use. We have specific linking to purchase extra sponges.

6. Does it kill the plant to remove it from a sponge (if I want to move it to a pot, for example)? Normally, it won’t, but you better wait until it’s vigorous to  improve survival rate.7. Why the pump never turns off? Please pull out the panel from the tank and insert it tightly until you can hear "Beep" sound.

8. Why the LED light can not be turned on? Please pull out the panel from the tank and insert it tightly until you can hear "Beep" sound, and then press the "POWER” button, the light is on.

Frequently Asked Questions & Answers FCC

04