HEAVY DUTY FLOOR BOXES >>> heavy duty in-screed floor box...
7
www.klinkmann.com 774 Red catalogue numbers: New products heavy duty in-screed floor box for concrete floors For highly frequented areas, requiring important mechanical resistance and/or washing down Conform to standard EN 60-670 and EN 50 085-2-2 Accessories for metal in-screed floor box 1 896 83 Normal load support Up to 8 KN load with deflection < 6 mm 1 896 84 Heavy load support Up to 20 KN load with deflection < 3 mm 6 896 39 Set of 2 conduit adaptors for metal cavity floor box Cat.No 896 34 Plates for metal in-screed floor boxes For metal in-screed floor box Cat.No 896 34 Use support Cat.No 896 83 or 896 84 All types of floors IP 66 plain cover (cover closed) Access trap for junction, no cable exit 1 896 85 IP 66 plain plate Marbled and tiled floors IP 66 plate (cover closed and plugs not connected) with central cable exit 1 896 86 IP 66 plate with central cable exit To receive 24 mosaic modules Supplied with all necessary wiring accessories supports Accessory for plate with central cable exit 1 896 87 IP 52 cable exit accessory for IP 66 cover plate Cat.No 896 86 Wooden floors 1 896 88 IP 30 plate with 2 lateral cable exits To receive 24 mosaic modules Supplied with all necessary wiring accessories supports Pack Cat.Nos Metal in-screed floor box Junction or connection point for concrete floor according to type of cover associated For junction of LV and ELV cabling and/or installation of floor boxes Height adjustable from 105 mm to 140 mm using 4 inserts located in the box corners and a tool adapting to electric drill or screwdriver Bendable side walls for assembling with different sizes of floor ducts Supplied with worksite protection cover to be replaced by blanking cover plate or mounting cover plate Allowing floor covering infill between 6 and 24 mm 1 896 34 Universal metal in-screed backbox NEW 896 34 + 896 83 + 896 85 896 34 + 896 83 + 896 88 896 34 + 896 83 + 896 86+ 896 87 These products are part of solutions for office equipment > See p. 772-773 >>> HEAVY DUTY FLOOR BOXES High resistance for high requirement For highly frequented areas, requiring important mechanical resistance and/or washing down. Perfect solution for shopping centres, car showrooms, exhibition halls, airports… Heavy load support: 8 and 20 KN load resistance 3 types of cover: - IP 66 plain cover for all types of floors - IP 66 for marble and tiled floors - IP 30 for wooden floors Meets sturdiness requirements NEW
Transcript of HEAVY DUTY FLOOR BOXES >>> heavy duty in-screed floor box...
www.klinkmann.com
774
cex-EP3
Red catalogue numbers: New products
heavy duty in-screed floor boxfor concrete floors
For highly frequented areas, requiring important mechanical resistance and/or washing downConform to standard EN 60-670 and EN 50 085-2-2
Accessories for metal in-screed floor box
1 896 83 Normal load supportUp to 8 KN load with deflection < 6 mm
1 896 84 Heavy load supportUp to 20 KN load with deflection < 3 mm
6 896 39 Set of 2 conduit adaptors for metal cavity floor box Cat.No 896 34
Plates for metal in-screed floor boxes
For metal in-screed floor box Cat.No 896 34Use support Cat.No 896 83 or 896 84
All types of floors IP 66 plain cover (cover closed)
Access trap for junction, no cable exit 1 896 85 IP 66 plain plate
Marbled and tiled floors IP 66 plate (cover closed and plugs not connected)
with central cable exit 1 896 86 IP 66 plate with central cable exit
To receive 24 mosaic modulesSupplied with all necessary wiring accessories supports
Accessory for plate with central cable exit 1 896 87 IP 52 cable exit accessory for IP 66 cover plate
Cat.No 896 86
Wooden floors 1 896 88 IP 30 plate with 2 lateral cable exits
To receive 24 mosaic modulesSupplied with all necessary wiring accessories supports
Pack Cat.Nos Metal in-screed floor box
Junction or connection point for concrete floor according to type of cover associatedFor junction of LV and ELV cabling and/or installation of floor boxesHeight adjustable from 105 mm to 140 mm using 4 inserts located in the box corners and a tool adapting to electric drill or screwdriverBendable side walls for assembling with different sizes of floor ductsSupplied with worksite protection cover to be replaced by blanking cover plate or mounting cover plateAllowing floor covering infill between 6 and 24 mm
1 896 34 Universal metal in-screed backbox
NEW
896 34 + 896 83 + 896 85
896 34 + 896 83 + 896 88
896 34 + 896 83 + 896 86+ 896 87
These products are part of solutions for office equipment > See p. 772-773
>>>HEAVY DUTY FLOOR BOXES
High resistance for high requirement For highly frequented areas, requiring important mechanical resistance and/or washing down.
Perfect solution for shopping centres, car showrooms, exhibition halls, airports… Heavy load support: 8 and 20 KN load resistance 3 types of cover:
- IP 66 plain cover for all types of floors- IP 66 for marble and tiled floors- IP 30 for wooden floors
Meets sturdiness requirements
NEW
www.klinkmann.com
775
cex-EP3
Red catalogue numbers: New products
floor service outlet boxes and access unitsfor raised or concrete floors
Conform to standard EN 60-670 and EN 50085-2-2 (p. 777) Workstation connection for raised floor or concrete floor, using plastic or metal backbox (p. 776) Supplied with reversible stainless steel cover or cover for carpet For technical space ≥ 75 mmMounting boxes (for horizontal wiring device positioning):- height adjustable from 75 to 105 mm- ensure perfect cable separation- takes 2 flexible conduits Ø20 mm- shifted from one another for optimal connection for all sockets- take marking labelsEasy opening cover with rings and holding in open position during connection
896 05 896 11 equipped with Mosaic sockets
Pack Cat.Nos Adjustable height from 75 to 105 mm to be equipped
Floor service outlet boxes equipped with empty mounting boxes To be equipped with Mosaic wiring accessories
12 modules 1 896 05 With stainless steel cover
Grey RAL 7031 1 896 06 With cover for carpet
Grey RAL 7031 1 896 07 With cover for carpet
Beige RAL 1019
18 modules 1 896 10 With stainless steel cover
Grey RAL 7031 1 896 11 With cover for carpet
Grey RAL 7031 1 896 12 With cover for carpet
Beige RAL 1019
24 modules 1 896 15 With stainless steel cover
Grey RAL 7031 1 896 16 With cover for carpet
Grey RAL 7031 1 896 17 With cover for carpet
Beige RAL 1019
Pack Cat.Nos Height reduced to 65 mm to be equipped (continued)
16 modules For installing 8 x 2 modules Mosaic 1 896 25 With stainless steel cover, grey RAL 7031 1 896 26 With cover for carpet, grey RAL 7031 1 896 27 With cover for carpet, beige RAL 1019
Height reduced to 65 mm to be equipped
For technical space ≥ 65 mm For renovation with reduced height technical floor or for concrete floor Supplied with reversible stainless steel cover or cover for carpet or parquet Mounting boxes (for vertical wiring device positioning): - supplied with blanking plates requiring sufficient space between the sockets if angled plugs are used - to be equipped with 2 module Mosaic socket outlets - takes marking labels - ensures perfect cable separation Easy opening cover by rings and holding in open position during connection
10 modules For installing 4 x 2 modules Mosaic and
2 x 1 module Mosaic 1 896 20 With stainless steel cover, grey RAL 7031 1 896 21 With cover for carpet, grey RAL 7031 1 896 22 With cover for carpet, beige RAL 1019
Plastic floor boxes for concrete floors (p. 776)
896 49
896 44
896 26
Access unitsAccess units for raised or concrete floor (minimum height 90 mm)Supplied with stainless steel cover or cover for carpetGrey RAL 7031
Small dimensions1 896 90 With cover for carpet1 896 91 With stainless steel cover
Large dimensions1 896 94 With cover for carpet1 896 95 With stainless steel cover
Floor service outlet boxes - 3 modulesAccess units for raised or concrete floor (minimum height 80 mm)To be equipped with: 1 Mosaic socket outlet 2P+E 2 modules and 1 Mosaic RJ 45 - 1 module or 1 Arteor socket outlet 2P+E and 1 Arteor RJ 45 1 moduleGrey RAL 7031
1 896 44 Floor service outlet box - 3 modules1 896 49 Flush-mounting box for concrete for Cat.No 896 44
These products are part of solutions for office equipment > See p. 772-773
www.klinkmann.com
776
cex-EP3
metal and plastic backboxesfor concrete floor
Pack Cat.Nos Adjustable metal backbox for concrete floor
Universal backbox For junction of LV and ELV cabling and/or installation
of floor boxes Height adjustable from 56 mm to 140 mm using 4 screws located in the box corners and a tool adapting to electric drill or screwdriver Bendable side walls for joining with different sizes of floor ducts Supplied with worksite protection cover to be replaced by blanking cover plate or mounting cover plate
1 896 34 Universal metal in-screed backbox
Cover plates Thickness 3 mm 5 896 35 Blanking cover plates for simple junction 5 896 36 Adaptor plate for floor boxes
12 modules, or floor boxes of reduced height 10 modules
5 896 37 Adaptor plate for floor boxes 18 modules
5 896 38 Adaptor plate for floor boxes 24 modules, or floor boxes of reduced height 16 modules
896 34
Auto-adjustable plastic backboxes for concrete floor
For integration of floor boxes in in-screed floor installations Power supply by flexible conduits Ø16, 20 and 25 mm Supplied with polystyrene for easy installation
1 896 30 For integration of 12 modules floor boxes or 10 modules reduced height floor boxes
1 896 31 For integration of 18 modules floor boxes 1 896 32 For integration of 24 modules floor boxes or 16
modules reduced height floor boxes
896 30
Floor service outlet boxes (p. 775)
PVC floor duct for concrete floor
Pack Cat.Nos PVC floor duct
IP 40 - IK 08 For distributing LV and ELV cabling in concrete floor installations Combines with metal backbox for cable junction or floor box installation Length: 2 m Can be assembled to make the number of compartments required (for immediate use or standby)
Height 28 mm 16 896 60(1) 50 x 28 mm with 1 compartment 12 896 61(1) 100 x 28 mm with 2 compartments 14 896 62(1) 150 x 28 mm with 3 compartments 6 896 63(1) 200 x 28 mm with 4 compartments
Height 38 mm 12 896 67(1) 50 x 38 mm with 1 compartment 16 896 68(1) 100 x 38 mm with 2 compartments 10 896 69(1) 150 x 38 mm with 3 compartments 8 896 70(1) 200 x 38 mm with 4 compartments
Snapfitting of sectionsCat.No 896 61 with Cat.No 896 60
(1) Number of metres contained in pack
Fixing / coupling accessories
For fixing floor ducts on floor and junction between ducts
5 896 74 For duct width 100 mm 5 896 75 For duct width 150 mm 5 896 76 For duct width 200 mm 5 896 77 For duct width 250 mm 5 896 78 For duct width 300 mm
896 60
896 61
896 69
896 74
www.klinkmann.com
777
cex-EP3
PVC floor duct and backboxesfor concrete floor
PVC floor duct and backboxes installation principle
Underfloor box fixing Height adjustment Placing the floor ducts Placing the lateral sides
Pouring the concrete Cover change Placing the floor box
450
450
480 56 -
140
Dimensions
Selection tables for mounting cover plate and floor box
Cover For floor boxes plate Adjustable height Reduced height 75 to 105 mm 65 mm
12 modules 10 modules 896 36 896 05/06/07 896 20/21/22
18 modules 896 37 896 10/11/12
24 modules 16 modules 896 38 896 15/16/17 896 25/26/27
PVC floor boxes and underfloor boxes installation principle
Choice of plastic underfloor box according to the floor box to be installed
A
H
B
18-48 75 65 105
A A B B
18-48
Cat.Nos A (mm) B (mm)
896 05/06/07/20/21/22 215 255
896 10/11/12 255 255
896 15/16/17/25/26/27 310 255
floor service outlet boxes and access units
Classification for distribution system by floor
Composition and function with distribution systems embedded in floor
Composition and function with distribution sytem on floor
Standard EN 50085-2-2 concerns systems for distributing currents in the floor (sunken or surface-mounted) It ensures consistent performance along the entire distribution length up to the user connection point
Embedded in floor On floor Heavy duty floor
system
6.2Resistance to impact for installation and application
5 J 5 J 5 J
6.3 Minimum storage and transport temperature - 25 °C - 25 °C - 25 °C
6.3 Minimum installation and application temperature - 5 °C - 5 °C - 5 °C
6.3 Maximum application temperature + 60 °C + 60 °C + 60 °C
6.4 Resistance to flame propagation Non propagating Non propagating Non propagating
6.5 Electrical continuity characteristics Without continuity Without continuity Without continuity
6.6 Electrical insulating characteristics
Without electrical insulating characteristic
Without electrical insulating characteristic
Without electrical insulating characteristic
6.7 Degree of protection provided by enclosure IP30 IP20 IP66(A)
IP30(B)
6.9 System access cover retention With a tool With a tool With a tool
6.101 Floor treatment Dry floor treatment
Dry floor treatment
Wet floor treatment
6.102Resistance to a vertical load applied over a small surface area
750 N 750 N 3000 N
6.103
Optional classification according to resistance to a vertical load applied over a large surface area
3000 N 3000 N 15000 N
Floor service outlet boxes and access units and heavy duty boxes
With metal flush-mounting boxes
Metal boxes Plastic trunking Fixing
896 05 896 06 896 07 896 20 896 21 896 90 896 91
896 34 +
896 36
see (1) see (2)896 10 896 11 896 12
896 34 +
896 37
896 15 896 16 896 17 896 25 896 26 896 94 896 95
896 34 +
896 38
(A) 896 85 896 86
(B) 896 88
896 34 +
896 84see (1) see (2)
Dim. trunking 92 x 20 Cat.No 328 00
Nbr of compartments 4
Accessories for over floor trunking
Distribution box Cat.No 328 01
Flat angle Cat.No 328 02
Cover joint Cat.No 328 03
End cap Cat.No 328 07
Mini-columnWhite Cat.No 307 42
Alu Cat.No 307 29
Column modules see p. 788-789
Width (mm) 100 150 200 250 300
Height (mm) 28 38 28 38 28 38 28 38 28 38
Plastic trunking (1) 896 61 896 68 896 62 896 69 896 63 896 70
896 63 +
896 60
896 70+
896 67
896 63 +
896 61
896 70+
896 68
Fixing (2) 896 74 896 75 896 76 896 77 896 78
A B
www.klinkmann.com
778
cex-EP3
grommetflush-mounting
floor unitssurface or flush-mounting
317 49Equipped with sockets, to be ordered separately
317 48
Pack Cat.Nos Surface-mounting floor sockets to be equipped
Empty electrical wiring accessories to be equipped with Mosaic screw connection sockets (p. 798) Equipped with pivoting wiring supports for easy installation of sockets Can be combined with floor duct Cat.No 328 00 Can be illuminated with LED Cat.No 899 06
5 317 48 2 x 4 modules 5 317 49 3 x 4 modules 10 899 06 LED to be wired, 230 V
High luminescence orange neon
6503 00 6503 49
6503 90
Flush-mounting floor sockets to be equipped
Empty receptacles for floor sockets 1 6503 00 3 modules - Aluminium 1 6503 50 3 modules - Brass 1 6503 49 2 x 3 modules - Aluminium
Flush-mounting boxes for floor sockets 10 6503 90 3 modules - Plastic 10 6503 31 2 x 3 modules
For floor box Cat.No 6503 49 - Plastic 1 6503 32 3 modules (can be assembled with another
Cat.No 6053 32 to compose a 2 x 3 modules box) Metallic
893 07
Pack Cat.Nos Small aluminium access grommet
Body - cast aluminium Main jaw - injection mouled plastic Nylon 66 Inner jaws - closed cell Neoprene Recommended hole cut-out size: 127 mm diameter Will fit floor tile thickness range of 25 to 55 mm
Can form the base of a cable management products such as power posts and poles Standard depth: 60 mm
1 893 07 Access grommet IP 20 - IK 08
These products are part of solutions for office equipment > See p. 772-773
www.klinkmann.com
779
cex-EP3
over floor trunking
328 00300 92 300 93
Conform to standard EN 50085-2-2 For creating a link between trunking, column, mini-column, floor units or protecting cables on passageways Supplied with cover
Pack Cat.Nos Over floor trunking 50 x 12 mm
Trunking 54 300 92(1) Length 2 m, supplied with cover
3 compartments Capacity 1: max. Ø9 mm Capacity 2: max. Ø6 mm IP 40 - IK 07 RAL 7030
Accessories 10 300 12 Cover joint
10 300 11 Flat angle
4 300 13 Junction box
Over floor trunking 75 x 18 mm
Trunking 36 300 93(1) Length 2 m, supplied with cover
3 compartments Capacity 1: max. Ø14 mm Capacity 2: max. Ø11 mm IP 40 - IK 07 RAL 7030
Accessories 10 300 19 Cover joint
10 300 18 Flat angle
4 300 13 Junction box
Pack Cat.Nos Over floor trunking 92 x 20 mm
Trunking 20 328 00(1) Length 2 m, supplied with cover
4 compartments Equipped with 2 adhesive strips for better floor fixing Capacity 1: max. Ø14.5 mm Capacity 2: max. Ø9.5 mm IP 40 - IK 08 RAL 7016
Accessories 10 328 07 End cap
10 328 03 Cover joint
5 328 02 Flat angle
1 328 05 Connection for mini-trunking installed as 60 x 20 or 75 x 20 skirting trunking
5 328 01 Distribution box For spurs in 4 directions with separation of currents
Junction for trunkings
To be used with Cat.No 328 00 5 107 71 + 106 90 For cover 65 mm 5 107 72 + 106 90 For cover 85 mm
5012
2
1
75
2
1
18
92
20
2
1
21 : maxi Ø 14,5 mm : maxi Ø 9 mm
These products are part of solutions for office equipment > See p. 772-773
(1) Number of metres in pack
www.klinkmann.com
780
cex-EP3
Red catalogue numbers: New products
desktop multi-outlet extensions to be equipped
Pack Cat.Nos Empty aluminium extensions
Aluminium extensions with cable guide (reversible) To be equipped with Mosaic sockets
1 535 90 8 modules 1 535 91 12 modules 1 535 92 16 modules
535 90
535 99 535 97
535 91
Accessories
Fixing accessory 5 535 99 Fixing accessory to clip on desktop
Cable worm Very suitable solution for a safe and design
protection of the cabling between desk and floor 1 535 97 2 compartments
Length: 770 mm Ø70 mm Translucid
desktop multi-outlet extensions without cord
Pack Cat.Nos With high-current sockets
1 6535 50 - 6 x 2P+E sockets - 1 illuminated switch
1 6535 51 - 2 x 2P+E sockets - 2 x 2P+E tamperproof sockets
With high-current and low-current sockets
1 6535 52 - 4 x 2P+E sockets - 3 x RJ 45 sockets Cat. 6 UTP 1 module
1 6535 53 - 2 x 2P+E sockets - 2 x 2P+E tamperproof sockets - 2 x RJ 45 sockets Cat. 6 UTP - 2 blanking plates 1 module for VDI
Aluminium extensions with reversible cable guide for grouping cords of connected devices High current connection on terminal blocks with cable grip For low current sockets, connection on RJ 45 sockets or area distribution box with specific cord RJ 45/stripped Cat.Nos 517 96/97/98 (see p. 879) 2P+E sockets with 45° sloping screw recesses for easy insertion of angled plug 16 A - 250 VA - with shutters 3680 W at 230 VA per circuitSupplied without cordConform to IEC 60-884-1
6535 50
6535 51
6535 53
NEW
These products are part of solutions for office equipment > See p. 772-773
