Heat presentation for fbug (comp)
Transcript of Heat presentation for fbug (comp)
![Page 1: Heat presentation for fbug (comp)](https://reader035.fdocuments.us/reader035/viewer/2022062312/55622c6dd8b42af6668b524b/html5/thumbnails/1.jpg)
Heat
![Page 2: Heat presentation for fbug (comp)](https://reader035.fdocuments.us/reader035/viewer/2022062312/55622c6dd8b42af6668b524b/html5/thumbnails/2.jpg)
Radiant HeatScott User Group 2010
![Page 3: Heat presentation for fbug (comp)](https://reader035.fdocuments.us/reader035/viewer/2022062312/55622c6dd8b42af6668b524b/html5/thumbnails/3.jpg)
1) If Polycarbonate has a melting point of 200 degrees why doesn’t it melt in a 300 degree HFC.
2) If polycarbonate has a melting point of 200 degrees why did the visor melt when my HFC was only measuring 180 degrees.
A Most Common Question
![Page 4: Heat presentation for fbug (comp)](https://reader035.fdocuments.us/reader035/viewer/2022062312/55622c6dd8b42af6668b524b/html5/thumbnails/4.jpg)
Various Types of Heat• Convected heat• Conducted heat• Radiant heatConvection occurs when air or fluid passes over a heated service
Conduction is the process of heat transfer by direct contact with another surface
Radiation is heat transfer by infrared rays
![Page 5: Heat presentation for fbug (comp)](https://reader035.fdocuments.us/reader035/viewer/2022062312/55622c6dd8b42af6668b524b/html5/thumbnails/5.jpg)
• Hot air (atmosphere) – Convected heat (generally what is measured by the thermometers)
• Hot walls – Conducted heat (ie if leant against)• Radiant heat – Infrared energy from surrounding.
In a Hot Fire Container
![Page 6: Heat presentation for fbug (comp)](https://reader035.fdocuments.us/reader035/viewer/2022062312/55622c6dd8b42af6668b524b/html5/thumbnails/6.jpg)
• Infrared energy can not be measured with a with a thermometer.
• Therefore radiant heat can only be measured using calorimetres
• Rules to remember about thermal radiation: • All objects above absolute zero (-273oC) emit infrared rays in a straight line in all
directions.• Hotter objects emit more total radiation energy per unit surface area • Hotter objects emit photons with a higher average energy (which means shorter
wavelength/higher frequency).
Measurement of Radiant Heat
![Page 7: Heat presentation for fbug (comp)](https://reader035.fdocuments.us/reader035/viewer/2022062312/55622c6dd8b42af6668b524b/html5/thumbnails/7.jpg)
Radiant energy that strikes a surface can be
1) Reflected 2) Absorbed 3) Transmitted (Semitransparent material)
Radiant Energy
![Page 8: Heat presentation for fbug (comp)](https://reader035.fdocuments.us/reader035/viewer/2022062312/55622c6dd8b42af6668b524b/html5/thumbnails/8.jpg)
• Thermal radiation, even at a single temperature, occurs at a wide range of frequencies.
• The main frequency (or colour) range of the emitted radiation includes higher and higher frequencies as the temperature increases. For example, a red hot object radiates enough in the long wavelengths (red and orange) of the visible band to see, which is why it appears red. If it heats up further, it also begins to emit discernible amounts of green and blue light, and the spread of frequencies mentioned in the first point make it appear white. We then say the object is white hot. However, even at a "white-hot" temperature of 2000 K, 99% of the energy of the radiation is still in the infrared.
• The total amount of radiation, of all frequencies, goes up very fast as the temperature rises (it grows as T4, where T is the absolute temperature of the body). An object at the temperature of a kitchen oven (about twice room temperature in absolute terms: 600 K vs. 300 K) radiates 16 times as much power per unit area. An object at the temperature of the filament in an incandescent bulb (roughly 3000 K, or 10 times room temperature) radiates 10,000 times as much per unit area.
![Page 9: Heat presentation for fbug (comp)](https://reader035.fdocuments.us/reader035/viewer/2022062312/55622c6dd8b42af6668b524b/html5/thumbnails/9.jpg)
• Radiant heat can only be measured using calorimetres
• Infrared energy can not be measured with a thermometer.
• If a hot fire container is measured at 300oC that is the air temperature and not the radiant heat.
• Depending upon the heat source there could be massive amounts of radiant heat or very little.
![Page 10: Heat presentation for fbug (comp)](https://reader035.fdocuments.us/reader035/viewer/2022062312/55622c6dd8b42af6668b524b/html5/thumbnails/10.jpg)
Radiation Intensity (kW/m2)
Level of Damage
37.5 Sufficient to cause damage to process equipment
25 Minimum energy required to ignite wood at indefinitely long exposure
12.5Minimum energy required for piloted ignition of wood, and melting of plastic tubing. This value is typically used as a fatality number
9.5 Sufficient to cause pain in 8 seconds and 2nd degree burns in 20 seconds
5Sufficient to cause pain in 20 seconds. 2nd degree burns are possible. 0 percent fatality. This values often used as an injury threshold.
1.6 Discomfort for long exposures
![Page 11: Heat presentation for fbug (comp)](https://reader035.fdocuments.us/reader035/viewer/2022062312/55622c6dd8b42af6668b524b/html5/thumbnails/11.jpg)
• 1 TDU = 1 (kW/m2)4/3s.
Level of ExposureResult
Mean Range
92 86-103 Pain
105 80-130 Threshold First Degree Burn
290 240-350 Threshold Second Degree Burn
1000 870-2600 Threshold Third Degree Burn
Thermal Dose Unit
![Page 12: Heat presentation for fbug (comp)](https://reader035.fdocuments.us/reader035/viewer/2022062312/55622c6dd8b42af6668b524b/html5/thumbnails/12.jpg)
1) If Polycarbonate has a melting point of 200 degrees why doesn’t it melt in a 300 degree HFC.
1) If polycarbonate has a melting point of 200 degrees why did the visor melt when my HFC was only measuring 180 degrees.
A Most Common Question
![Page 13: Heat presentation for fbug (comp)](https://reader035.fdocuments.us/reader035/viewer/2022062312/55622c6dd8b42af6668b524b/html5/thumbnails/13.jpg)
• Hot air (atmosphere) – Convected heat (generally what is measured by the thermometers)
• Hot walls – Conducted heat (ie if leant against)• Radiant heat – Infrared energy from surrounding.
In a Hot Fire Container
![Page 14: Heat presentation for fbug (comp)](https://reader035.fdocuments.us/reader035/viewer/2022062312/55622c6dd8b42af6668b524b/html5/thumbnails/14.jpg)
Gas = X atoms per Cm3
Liquid = 1000X atoms cm3
Solid = 2000X atoms Cm3
Ratio of 1:1000:2000
3 States of Matter
![Page 15: Heat presentation for fbug (comp)](https://reader035.fdocuments.us/reader035/viewer/2022062312/55622c6dd8b42af6668b524b/html5/thumbnails/15.jpg)
• Hot Air does not contain much stored energy compared to a solid
• Therefore can not transfer much energy into the solid as for each “hot” gas atom there are 1000+ “cold” solid atoms
Air Temperature
![Page 16: Heat presentation for fbug (comp)](https://reader035.fdocuments.us/reader035/viewer/2022062312/55622c6dd8b42af6668b524b/html5/thumbnails/16.jpg)
Heat Transfer Mechanisms
Normal Cold Hot (maybe melting)
Warm(not melting)
Warm with very hot surface
Cold Air from DV
Convected heat from surroundings
Radiant Heat
Visors
![Page 17: Heat presentation for fbug (comp)](https://reader035.fdocuments.us/reader035/viewer/2022062312/55622c6dd8b42af6668b524b/html5/thumbnails/17.jpg)
Normal
Inside mask Outside mask
![Page 18: Heat presentation for fbug (comp)](https://reader035.fdocuments.us/reader035/viewer/2022062312/55622c6dd8b42af6668b524b/html5/thumbnails/18.jpg)
Cold Air from DV
DV Working - NormalOutside Temp
![Page 19: Heat presentation for fbug (comp)](https://reader035.fdocuments.us/reader035/viewer/2022062312/55622c6dd8b42af6668b524b/html5/thumbnails/19.jpg)
Convected heat from surroundings(ie 300oC air)
DV Not Working - Heat(Visors Heats Up)
![Page 20: Heat presentation for fbug (comp)](https://reader035.fdocuments.us/reader035/viewer/2022062312/55622c6dd8b42af6668b524b/html5/thumbnails/20.jpg)
1) If Polycarbonate has a melting point of 200 degrees why doesn’t it melt in a 300 degree HFC.
1) If polycarbonate has a melting point of 200 degrees why did the visor melt when my HFC was only measuring 180 degrees.
Question 1
![Page 21: Heat presentation for fbug (comp)](https://reader035.fdocuments.us/reader035/viewer/2022062312/55622c6dd8b42af6668b524b/html5/thumbnails/21.jpg)
Convected heat from surroundings
Cold Air from DV
DV Working - Heat(Visor heats up but DV air also cools visor)
![Page 22: Heat presentation for fbug (comp)](https://reader035.fdocuments.us/reader035/viewer/2022062312/55622c6dd8b42af6668b524b/html5/thumbnails/22.jpg)
1) If polycarbonate has a melting point of 200 degrees why did the visor melt when my HFC was only measuring 180 degrees.
Question 2
![Page 23: Heat presentation for fbug (comp)](https://reader035.fdocuments.us/reader035/viewer/2022062312/55622c6dd8b42af6668b524b/html5/thumbnails/23.jpg)
DV Working - Heat(Visor heats up but DV air also cools visor)
Radiant heat added which increases visor surface temperature dramatically
![Page 24: Heat presentation for fbug (comp)](https://reader035.fdocuments.us/reader035/viewer/2022062312/55622c6dd8b42af6668b524b/html5/thumbnails/24.jpg)