HaoWorks H2 UserManual · 2018. 9. 19. · 7) Support FM,TFcard, USB disk play mode....

SHENZHEN SHIDU DIGITAL CO.,LTD

21635866 29105099Email:[email protected] Website:www.10shidu.com

HaoWorks H2 User ManualPlease read the instruction carefully before using it.

Features:1) This speaker can work with any devices (DVD, VCD, CD, LD, TV, MP3, Radio, Electronic piano, etc…) with AUX output.

2) SHIDU original sound amplification electroacoustic system, maximum output power 30W.

3) 5.25 inch bass speaker and 1.5 inch independent tweeter.

4) 7.4V 4000mAh A grade lithium battery, can support 5~6 hours working time.

5) With Bluetooth 4.2 icloud control, which support sync textbook and and music online playing, wireless Karaoke.

6) Double devices TWS Bluetooth Double channel.

7) Support FM,TF card, USB disk play mode. Independent audio Input and Output interface.

8) One key to eliminate the original sound, switch freely between accompaniment and original.

9) UHF Wireless through-wall technology, high sensitivity Moving-Coil microphone, stable signal and clear sound.

Function Illustration

1.Mic

7.VOL

2.MIC PRIORITY

8.POWER

3.MIC VOL

9.INPUT

4.ECHO

10.REC/PLAY

5.BASS

11.MUSIC/KARAOKE

6.TREBLE

12.PREVIOUS

13.PLAY/PAUSE 14.NEXT 15.AUDIO INPUT 16.USB(Limited To Data Transmission) 17.TF

18. DC 15V IN 19.DEL REC 20.LOOPING 21.MUSICAL SELECTION KEY

Common Function Illustration◎Vol: To adjust the main volume◎TRELBE:To adjust treble effect◎BASS:To adjust bass effect◎MIC-VOL: To adjust the volume of MIC◎Echo: To adjust echo effect of MIC

mailto:[email protected]://www.10shidu.com/http://www.10shidu.com/



HaoWorks H2 User ManualBuilt-in MP3:

◎USB slot: Support USB flash drive,◎TF card slot: Support TF card

◎Support MP3 WAV WMA FLAC APE format，prominent sound quality，Hi-Fi stereo design，bring you whole new Music experience.◎Input: To select AUX in mode, Bluetooth mode, TF card mode & USB flash drive ,FM mode◎PlAY/PAUSE: In audio playing mode, press it to pause; press it again to play.◎Pre/PAUSE: Press to select previous or next audio file.◎ Key: Press to switch between accompaniment and original in audio playing mode.

FM Function:◎Switch on the speaker, short press "INPUT" to choose the FM mode with the screen showing Radio frequency; Long press to enter into

automatic channels searching; After searched successfully, the device will save the channel automatically. And please press or to

choose the saved channels.

AUX FUNCTION:

1. Connected an AUX cable with another device,please short press"INPUT" to AUX mode.

2. “MIC PRIORITY” function is worked during the AUX mode

REC Function:1. Connected with wireless or wired microphone, in any mode, press and hold on to enter into REC mode to record with inserting storage (USB

flash drive or TF card). Press ”REC/PLAY” again to stop recording, save ”REC/PLAY” the audio files and play the recordings.

2. In music mode, press ”REC/PLAY” to enter into recordings play back mode with inserting storages (which have recordings). It will play the last

recording by default and please press or to select the previous and next recordings.

3. In recordings play back mode, please press “LOOPING” on remote control to select single cycle and all cycle.

Bluetooth Function:1.Switch on the speaker and press "INPUT" to enter into Bluetooth mode. (The Bluetooth mode is ready with voice prompt “Bluetooth is waitingfor connection” and “BLUE” on the screen.)2. Turn on the Bluetooth function of your devices and search “H2”. Click and it will be successfully with a voice prompt “Bluetooth isconnected”.3. After successful connection, it’s possible to play the audio files(Teaching Material,Training Material,Music) in your devices.It can also work withthe wireless microphone ,to realize Poetry recitation accompanied by music and Synchronous karaoke.

Double devices TWS Bluetooth Double ChannelStep1: Open two devices and press " INPUT " to enter into Bluetooth mode .Long press " INPUT "of one device to enter into pairing status .Bluetoothicon of another will be light constantly which means TWS function is activated.Step2: Enter into “ Settings “ of mobile and turn on Bluetooth function. Then please search " H2 " and connect. Two devices play simultaneouslyachieve a surrounded stereo sound.

Step3: Long press " INPUT " one of them, quit out the function.

About Charging:1. Please use the standard adapter, the other end connects with the power supply AC 110~240V to charge. Please unplug the adapter timely after

fully charged (the charging time is normally 6~8 hours).




HaoWorks H2 User Manual2.Battery status: There are 4 battery indicators on the screen and each represents 25%. Full is 100%, 3 are 75%... Please charge it timely when the

speaker reminds with voice prompt “Low battery, please charge”. The battery indicator will blink when charging and it will stop blinking after fully

charged and 4 indicators are full.

Please charge it 1~2 hours more after fully charged to lengthen the life of battery. Please don’t over charge too much time.

3.Please recharge the battery within 48 hours if the battery is too low.Keep the battery have electricity even if it don't work for a long time.

Please recharge the battery in open area when it is completely discharged and automatic shut down to avoid combustible.

Specification:Power output:≤30W

Sensitivity:550±30mV

SNR≥70dB

Frequency response:20Hz-20KHZ.

Charging voltage: DC 9V 1.2A MAX.

Wireless Microphone Operation:(Limited to wireless version)1.Switch ON / OFF:

◎Long press on the wireless microphone to switch on and the display will show a default frequency point.

Please open the speaker to amplify voice.

◎Long press on power on state will turn off the microphone and screen go out.

2. Pair the UHF Wireless MIC Manually(This pairing way is used when the MIC is no sound)

Step 1:Turn on the speaker and find the “INPUT” button;

Step 2:Switch on the wireless hand-held MIC and twist off the shell; then press “ ” &” ”at the same time for 3seconds,until screen” ”indicator flashes;

Step 3:Quickly short press the "INPUT" button for three times to enter into pairing status with a voice prompts "UHF" is

waiting for connection;

Step 4:Please wait about 3s until the signal indicator””on the handheld mic from flashing to keep long lights. It means thewireless mic pair successfully with the speaker.

Noted:Please finish pairing operation within 10s as the ” ” indicator can only flashes about 10s;Noted: please don’t press the "INPUT" button to enter into“UHF” model after turn on the speaker;Notes: Under the pairing status, long press “ ” &” ” on the hand-held microphone to disconnect wireless signal

with voice prompt “UHF is disconnected”. Repeat step 2& step 3 or pairing the UHF wireless MIC manually.

3.Battery Indication of UHF Wireless MIC:

In working status, it has sufficient battery power with indication showed on screen; it’s low battery with indication showed on screen and

please change the battery timely.

Note: Please open the battery cover properly and put the batteries. (Please note the positive & negative anode.)




HaoWorks H2 User Manual

Solve some normal problems by yourself:Trouble Possilble reasons Measures

Switch on the speaker but

no sound

1.Main machine is running out of

powerPlease recharge it to switch on.

2.No audio input Please use another better audio

3.Haven’t turned on the volume Please adjust the volume properly.

With sound distortion1.The volume is too high Please turn down the volume.

2.The speaker is broken Please contact us for maintenance.

No sound with Karaoke

1.Haven’t inserted the wired MIC Please insert the wired MIC.

2.Haven’t switched on the MIC Please turn on the MIC

3.Haven’t turned on the MIC volume

4.The UHF wireless is disconnected or

wireless MIC is low battery

Please repair the UHF wireless microphone, Or please change the

battery

No sound with MP3 playing

1.The audio’s format in USB flash drive

or TF card is wrongPlease turn the format to MP3

2.Chaotic procedure with wrongoperation

Please restart the speaker

3.Haven’t inserted

drive/TF card properly

the USB flashPlease insert the USB/TF card properly.

Can only work several

minutes after charged or

have to work with Adapter

1.The battery is broken Please change a new sample battery

2.The connecting cable of battery is

loosened or disconnectedPlease contact us for maintenance

3.Hasn’t full charged the speaker Please full charge it before using

Pair unsuccessfully 1. Turn on the speaker and enter into“UHF” model firstly;

Please firstly turn on the wireless handheld mic and press the“ ”

“ ”“ ”

“ ”

“ ”

“ ”&

“ ”at the same time for 3 seconds until screen indicator

flashes;

Then quickly short press the "INPUT" button for three times to enter

into UHF model.

2. The indicator flasher turn onlight constantly before pairing;

Please finish pairing operation within 10s as the indicator can

only flashes about 10s; If the indicator flasher turn on light

constantly before pairing, then please repeat step2 again to press the

“ ” “ ”& at the same time for 3 seconds until screen indicator

flashes;




HaoWorks H2 User ManualHaoWorks Guarantee:

30 days return and refund without any reason + 12-month warranty + Lifetime technical support

Please don’t forget to contact us at below for any assistance you needed.

[email protected]

mailto:[email protected]:[email protected]://www.10shidu.com/http://www.10shidu.com/

Features:Function IllustrationCommon Function IllustrationBuilt-in MP3:FM Function:REC Function:Bluetooth Function:Double devices TWS Bluetooth Double ChannelAbout Charging:Specification:Wireless Microphone Operation:(Limited to wireless1.Switch ON / OFF:

Step 1:Step 2:Switch on the wireless hand-held MIC and twist offStep 3:Step 4:Please wait about 3s until the signal indicator””oNoted: Please finish pairing operation within 10s 3.Battery Indication of UHF Wireless MIC:

Solve some normal problems by yourself:

HaoWorks H2 UserManual · 2018. 9. 19. · 7) Support FM,TFcard, USB disk play mode....

Documents

Transcript of HaoWorks H2 UserManual · 2018. 9. 19. · 7) Support FM,TFcard, USB disk play mode....