Gyproc Plasterboard 2.1 - Boards_0.pdfGypsum Industries manufactures an extensive range of...
Transcript of Gyproc Plasterboard 2.1 - Boards_0.pdfGypsum Industries manufactures an extensive range of...
Gyproc Plasterboard
2
book2_jan10a:Products-R10 (07-04).qxd 15/04/2010 16:09 Page 49
50
www.gyproc.ie
book2_jan10a:Products-R10 (07-04).qxd 15/04/2010 16:09 Page 50
51
T 00353 1 629 8400 F 00353 1 623 7054 E [email protected]
Gypsum Industries manufactures an extensive range ofplasterboards which, as part of a building system aredesigned to meet specific requirements relating to soundinsulation and resistance to fire, moisture and impact.The tables below provide information on typicaldimensions and edge profiles available.
Reaction to FirePlasterboard linings provide good fire protection owingto the unique behaviour of the non-combustible gypsumcore when subjected to high temperatures.
Within national Building Regulations, plasterboard is designated a ‘material of limited combustibility’. As a result of the performance achieved when tested to BS 476: Part 6: 1989 and BS 476: Part 7: 1997, the surfacesof Gyproc plasterboards and the exposed plasterboardsurface of Gyproc thermal laminates are designated Class 0.
Board weightsAll weights stated in the following tables areapproximate. Board weights can vary. If the boardweight is critical to the design, please contact theTechnical Sales Department.
Table 1 Classification
Test Performance....................................................................................................................BS 476: Part 6: 1989 Index of performance (I) notMethod of test for fire exceeding 12 and a sub-index (i1)propagation for products not exceeding 6 (both sides)
BS 476: Part 7: 1997 Class 1 (both sides)Surface spread of flametests for materials....................................................................................................................
Glasroc F Multiboard and Glasroc F Firecase are paperless,glass reinforced gypsum boards, which are designated as ‘non-combustible’ when tested to BS 476: Part 4: 1970(1984).
Technical Guidance Document B (Fire Safety) of the BuildingRegulations was amended in 2006 to also allow the‘Euroclass’ system to be used for demonstrating compliancewith reaction to fire requirements. The following tables listthe ‘Euroclass’ reaction to fire classifications.
INTRODUCTION
Bo
ard
s
2.1
book2_jan10a:Products-R10 (07-04).qxd 15/04/2010 16:09 Page 51
52
www.gyproc.ie
Board type Description Board Approx. Thermalthickness weight resistancemm kg/m2 m2K/W
Gyproc WallBoard backed with avapour control membrane. Used forwall and ceiling linings where vapourcontrol and a plasterboard lining arerequired in one fixing operation.
EN14190 Reaction to fireB-s1, d0 (front andback). Wallboardfacing is EN520Type A.
GyprocWallBoardDUPLEX
9.5 7.6 0.04
12.5 9.7 0.05
15 13.0 0.06
Thermal conductivity 0.25 W/mKλ
9.5 1200 2438
12.5 600 2400
2438
12.5 1200 2400
2438
2743
15 1200 2400
✔ ✔
✔
✔
✔
✔ ✔
✔
✔
Thickness Width Length Tapered Square Standards andmm mm mm edge edge certification
Board type Description Board Approx. Thermalthickness weight resistancemm kg/m2 m2K/W
12.5 9.7 0.05
15 13.0 0.06
Thermal conductivity 0.25 W/mK
The standard board product with ivory facepaper, suitable for most applications wherenormal fire, structural and acoustic performancelevels are specified. λ
9.5 1200 2438
2743
12.5 1200 2400
2438
2591
2700
2743
3000
3048
15 1200 2400
2700
3000
Thickness Width Length Tapered Square Standards andmm mm mm edge edge certification
✔ ✔
✔ ✔
✔ ✔
✔ ✔
✔
✔ ✔
✔ ✔
✔ ✔
✔ ✔
✔
✔
✔
EN 520 Type AReaction to fireA2-S1, d0
GyprocWallBoard
Bo
ard
s
2.1
book2_jan10a:Products-R10 (07-04).qxd 15/04/2010 16:09 Page 52
53
T 00353 1 629 8400 F 00353 1 623 7054 E [email protected]
Board type Description Board Approx. Thermalthickness weight resistancemm kg/m2 m2K/W
Easy-to-use round edge wallboard. Gyproc ‘4x2’s’
9.5 600 1219
12.5 600 1219
Thickness Width Length Round Standards andmm mm mm edge certification
✔
✔
EN 520 Type AReaction to fireA2-S1, d0
9.5 7.6 0.04
12.5 9.7 0.05
Thermal conductivity 0.25 W/mKλ
Board type Description Board Approx. Thermalthickness weight resistancemm kg/m2 m2K/W
A wallboard typically selected for use on ceilings.Gyproc ‘6x3’s’
9.5 900 1800
12.5 900 1800
Thickness Width Length Tapered Square Standards andmm mm mm edge edge certification
✔ ✔
✔ ✔
EN 520 Type AReaction to fireA2-S1, d0
9.5 7.6 0.04
12.5 9.7 0.05
Thermal conductivity 0.25 W/mKλ
Board type Description Board Approx. Thermalthickness weight resistancemm kg/m2 m2K/W
Easy-to-use wallboard which is ideal forattics or confined spaces.
12.5 600 2400
2438
Thickness Width Length Tapered Standards andmm mm mm edge certification
✔
✔
EN 520 Type AReaction to fireA2-S1, d0
12.5 9.7 0.05
Thermal conductivity 0.25 W/mKλ
Bo
ard
s
2.1
Gyproc ‘8x2’s’
book2_jan10a:Products-R10 (07-04).qxd 15/04/2010 16:09 Page 53
54
www.gyproc.ie
Board type Description Board Approx. Thermalthickness weight resistancemm kg/m2 m2K/W
12.5 11.1 0.05
15 12.8 0.06
Thermal conductivity 0.25 W/mK
Gypsum plasterboard with water repellent additives inthe core, encased in a special green paper liner. Suitableas a base for ceramic tiling in wet use areas. Also usedfor external soffits in sheltered positions. λ
Gyproc MoistureResistant
12.5 1200 2400
2700
3000
15 1200 2400
2700
3000
Thickness Width Length Tapered Square Standards andmm mm mm edge edge certification
✔
✔
✔
✔
✔
✔
EN 520 Type H1Reaction to fireA2-S1, d0
Board type Description Board Approx. Thermalthickness weight resistancemm kg/m2 m2K/W
19 16 0.08
Thermal conductivity 0.24 W/mK
A 19mm thick version of Gyproc FireLine MR with squareedges and green paper liner. Used as the core board inthe Gypsum Industries ShaftWall system to provide fireprotection with temporary moisture protection duringconstruction. Avaliable in square edge only.
λ
GyprocCoreBoard
19 598 3000
Thickness Width Length Tapered Square Standards andmm mm mm edge edge certification
✔ EN 520 Type D, F, H1Reaction to fireA2-S1, d0
Bo
ard
s
2.1
Gyproc Plank
Board type Description Board Approx. Thermalthickness weight resistancemm kg/m2 m2K/W
19 16 0.08
Thermal conductivity 0.19 W/mK
A 19mm thick version of GyprocWallBoard. Used as the main board inGypFloor SILENT, GypWall AUDIO andGypWall QUIET systems and timberframe separating walls.
λ
19 600 2400
Thickness Width Length Tapered Square Standards andmm mm mm edge edge certification
✔ EN 520 Type AReaction to fireA2-S1, d0
book2_jan10a:Products-R10 (07-04).qxd 15/04/2010 16:09 Page 54
12.5 11.0 0.05
15 13.0 0.06
Thermal conductivity 0.25 W/mK
Gyproc FireLine with pink face paper, backed with avapour control membrane. Combines a high fireperformance lining with vapour control. Can improvethermal resistance of lining when facing a minimum20mm cavity.
λ
Gyproc FireLineDUPLEX
Gyproc FireLine
Board type Description Board Approx. Thermalthickness weight resistancemm kg/m2 m2K/W
12.5 11.0 0.05
15 13.0 0.06
Thermal conductivity 0.25 W/mK
Gypsum plasterboard with glass fibre and other additivesin the core. Used in Gypsum Industries partition, walllining and ceiling systems to give increased fireprotection. Pink coloured face paper. λ
Gyproc FireLine
12.5 1200 2400
2700
3000
15 1200 2400
2700
3000
Gyproc FireLine DUPLEX
12.5 1200 2400
15 1200 2400
Gyproc FireLine MR
12.5 1200 2400
2700
3000
15 1200 2400
3000
Thickness Width Length Tapered Square Standards andmm mm mm edge edge certification
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
EN 520 Type D, FReaction to fireA2-S1, d0
EN 14190 - Reactionto fire B-s1, d0(front and back).FireLine facing isEN 520 Type D, F
12.5 11.1 0.05
15 13.0 0.06
Thermal conductivity 0.24 W/mK
Gyproc FireLine with water repellent additives in thecore, encased in a special pink paper liner. Used in walllining and partition systems where both fire protectionand moisture resistance are required. λ
Gyproc FireLineMR
EN 520 Type F, H1Reaction to fireA2-S1, d0
55
T 00353 1 629 8400 F 00353 1 623 7054 E [email protected]
Bo
ard
s
2.1
book2_jan10a:Products-R10 (07-04).qxd 15/04/2010 16:09 Page 55
56
www.gyproc.ieB
oard
s
2.1
12.5 10.9 0.05
15.0 13.1 0.06
Thermal conductivity 0.25 W/mK
Gyproc SoundBloc DUPLEX backed with a vapour controlmembrane. Used for wall and ceiling linings wherevapour control and a plasterboard lining are required inone fixing operation but also in areas where a higherdegree of sound insulation is required.
λ
GyprocSoundBlocDUPLEX
Gyproc SoundBloc
Board type Description Board Approx. Thermalthickness weight resistancemm kg/m2 m2K/W
12.5 10.9 0.05
15 13.1 0.06
Thermal conductivity 0.25 W/mK
Gypsum plasterboard with a higher density core.Designed for use in wall lining and partition systemswhere greater levels of sound insulation are required.Pale blue coloured face paper. λ
Gyproc SoundBloc
12.5 1200 2438
2700
3000
15 1200 2400
2700
3000
Gyproc SoundBloc DUPLEX
12.5 1200 2400
2438
15 1200 2400
Gyproc SoundBloc MR
12.5 1200 2400
3000
15 1200 2400
3000
Thickness Width Length Tapered Square Standards andmm mm mm edge edge certification
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
✔
EN 520 Type DReaction to fireA2-S1, d0
EN14190 Reaction tofire B-s1, d0 (front andback). Wallboard facingis EN520 Type A.
12.5 10.9 0.05
15.0 13.1 0.06
Thermal conductivity 0.25 W/mK
Gyproc SoundBloc MR with water repellent additives inthe core, encased in blue paper liner. Used in systemswhere both sound insulation and moisture resistanceare required. λ
GyprocSoundBlocMR
EN520 Type D,H1 Reaction to fireA2-S1, d0
book2_jan10a:Products-R10 (07-04).qxd 15/04/2010 16:09 Page 56
57
T 00353 1 629 8400 F 00353 1 623 7054 E [email protected]
Board type Description Board Approx. Thermalthickness weight resistancemm kg/m2 m2K/W
13.5 11.9 0.05
15.0 13.9 0.06
Thermal conductivity 0.25 W/mK
Gypsum plasterboard with heavy duty paper facingsand a higher density core. Designed for use in walllining and partition systems to give greater impactresistance in heavy use areas. Ivory coloured face paper. λ
GyprocDuraLine
Gyproc DuraLine
13.5 1200 2400
2700
3000
15 1200 2400
2700
Thickness Width Length Tapered Square Standards andmm mm mm edge edge certification
✔
✔
✔
✔
✔
EN 520Type D, F, I, RReaction to fireA2-S1, d0
Board type Description Board Approx. Thermalthickness weight resistancemm kg/m2 m2K/W
12.5 10.9 0.05
Thermal conductivity 0.25 W/mK
Easy-to-use SoundBloc which is ideal for attics orconfined spaces.
λ
GyprocSound Bloc‘8X2’S’
Gyproc SoundBloc ‘8x2’s’
12.5 600 2400
2438
Thickness Width Length Tapered Square Standards andmm mm mm edge edge certification
✔
✔ EN520 Type DReaction to fireA2-S1, d0
Bo
ard
s
2.1
book2_jan10a:Products-R10 (07-04).qxd 16/04/2010 12:13 Page 57
58
www.gyproc.ieB
oard
s
2.1
10.0 12.0 0.03
12.5 15.0 0.04
15.0 18.0 0.04
Thermal conductivity 0.35 W/mK
A gypsum fibreboard which benefits from increaseddensity, rigidity, durability and strength. Used particularlyas part of the GypWall EXTREME System.
λ
GyprocRigidur
10 1200 2400
2700
3000
12.5 1200 2400
2700
3000
15 1200 2400
2700
3000
Thickness Width Length Tapered Square Standards andmm mm mm edge edge certification
✔
✔
✔
✔ ✔
✔ ✔
✔ ✔
✔ ✔
✔ ✔
✔ ✔
Board type Description Board Approx. Thermalthickness weight resistancemm kg/m2 m2K/W
Floor board type Description Board Approx.thickness weightmm kg/m2
CSTB RA01-333
20 - 50 24.1 - 32.1
20 20 500 1500 24.1
25 25 500 1500 30.1
30MF 30 500 1500 25.7
35MF 35 500 1500 31.7
30HF 30 500 1500 26.1
35HF 35 500 1500 32.1
40PS 40 500 1500 24.5
50PS 50 500 1500 24.7
Floor Thickness Width Length Weight Standards andelement mm mm mm kg/m2 certification
Gyproc RigidurFlooring Elements
DIN 4102Note: Elements PSDIN 18164DIN 1055-3
30MF/35MF
30HF/35HF
40PS/50PS
A range of laminated Gyproc Rigidur boards for use onbuilt up flooring systems where increased soundperformance is required.
Gyproc Rigidur flooring boards.
Gyproc Rigidur flooring board laminated with 10mm ofmineral fibre.
Gyproc Rigidur flooring board laminated with 10mm ofsoftwood fibre.
Gyproc Rigidur flooring board laminated with20mm/30mm of polystyrene.
Element 20/25
book2_jan10a:Products-R10 (07-04).qxd 06/05/2010 11:37 Page 58
59
T 00353 1 629 8400 F 00353 1 623 7054 E [email protected]
Board type Description Board Approx. Thermalthickness weight resistancemm kg/m2 m2K/W
12.5mm Gyproc WallBoard with abacking of higher performanceexpanded polystyrene that is CFC andHCFC-free.
GyprocThermal
29 1200 2438
38 1200 2438
Thickness Width Length Tapered Square Standards andmm mm mm edge edge certification
✔
✔
29 10.0 0.50
38 10.1 0.74
WallBoard thermal conductivity0.25W/mK
Polystyrene thermal conductivity0.037 W/mK
λ
Board type Description Board Approx. Thermalthickness weight resistancemm kg/m2 m2K/W
26 7.0 0.85
36 7.5 1.32
46 8.0 1.76
56 8.5 2.40
66 9.0 2.88
76 9.5 3.55
86 10.0 3.83
MultiBoard thermal conductivity 0.286 W/mK
Phenolic foam thermal conductivity ranging from 0.021 W/mK to 0.024 W/mK depending onthickness of foam
6mm Glasroc F Multiboard with a backing offoil-faced HCFC and CFC-free phenolic foam providingintegral vapour control. Used to line the undersideof semi-exposed soffits to provide a high level ofthermal insulation.
λ
Glasroc FSoffitLine
26 1200 2400
36 1200 2400
46 1200 2400
56 1200 2400
66 1200 2400
76 1200 2400
86 1200 2400
Thickness Width Length Square Standards andmm mm mm edge certification
✔
✔
✔
✔
✔
✔
✔
Bo
ard
s
2.1
book2_jan10a:Products-R10 (07-04).qxd 15/04/2010 16:09 Page 59
60
www.gyproc.ie
Board type Description Board Approx. Thermalthickness weight resistancemm kg/m2 m2K/W
6 6 0.02
10 8.5 0.03
12.5 10.6 0.04
Thermal conductivity 0.286 W/mKλ
6 1200 2400
3000
10 1200 2400
3000
12.5 1200 2400
3000
Thickness Width Length Tapered Square Standards andmm mm mm edge edge certification
✔
✔
✔
✔
✔
✔
Glasroc FMultiBoard
EN 15283-1Type GM-F
A non-combustible glass reinforced gypsum board withexcellent fire protection properties and a high degree ofimpact resistance. Its inherent flexibility means it is alsoideal for curved applications. Can be used insemi-exposed situations such as eaves, canopies and carport under-linings.
Board type Description Board Approx. Thermalthickness weight resistancemm kg/m2 m2K/W
15 12.8 0.05
20 17.0 0.07
25 21.3 0.09
30 25.5 0.10
Thermal conductivity 0.286 W/mK
A high performance, non-combustible glass reinforcedgypsum board with excellent fire protection and screw /staple holding properties. Used primarily in theFireCase encasement system, giving fire protection tostructural steel. Can be used in semi-exposed situationssuch as eaves, canopies and car port under-linings. λ
15 600 3000
1200 2400
20 600 3000
1200 2000
25 1200 2000
30 1200 2000
Thickness Width Length Tapered Square Standards andmm mm mm edge edge certification
✔
✔
✔
✔
✔
✔
93/2935
EN 15283-1Type GM-F, H2
Glasroc F FireCase
Bo
ard
s
2.1
book2_jan10a:Products-R10 (07-04).qxd 15/04/2010 16:09 Page 60
61
T 00353 1 629 8400 F 00353 1 623 7054 E [email protected]
Board type Description Board Approx. Thermalthickness weight resistancemm kg/m2 m2K/W
12.5 13.0 0.06
12.5 1200 2400
2500
3000
Thickness Width Length Tapered Square Standards andmm mm mm edge edge certification
✔
✔
✔
GyprocPlacocem TileBacker
A cement board that combines a cement mixture withexpanded polystyrene beads, inserted between the twofaces of the panel and is ideal for use as a Tile BackerBoard for wet and humid areas.
Bo
ard
s
2.1
CSTB RA01-333
book2_jan10a:Products-R10 (07-04).qxd 15/04/2010 16:09 Page 61