Galaxy Mount Kits Manual - imgdataserver.com · Excalibur Bolts Base Plate Acetal Ring Locator...
Transcript of Galaxy Mount Kits Manual - imgdataserver.com · Excalibur Bolts Base Plate Acetal Ring Locator...
13401 Brooks DriveBaldwin Park, CA 91706p 626.338.8810f [email protected]
shademakerusa.com
© 2015 Shademaker. All rights reserved. SMOG-GMK-115
Concrete Mount Kit includes:A - Base PlateB - Stem Bolts (6)C- Excalibur Bolts - (6) 014x150mm - NOT INCLUDEDD - Allen Wrench
21
CONCRETE MOUNT KIT
VERY IMPORTANT: To achieve the exact desired position of the Galaxy canopy (when inthe open position or a perfectly symmetrical multiple Galaxy installation, it is imperative thatthe installation fitting be aligned correctly. Please follow the detailed instructions below.
The Galaxy Concrete Mount Kit has twelve (12) holes, six (6) are countersunk for bolting tothe concrete patio, and the other six (6) are tapped to accept the stem bolts.
STEP 1 Bolt Base PlateBolt base plate to concrete using six (6) 014x150mm Excalibur bolts (not included), makingsure two TAPPED HOLES are lined up in the direction of the desired primary mast andboom position. The countersunk holes are used for bolting to the concrete but should notbe used for alignment. You must align two TAPPED HOLES to achieve the desired position.
STEP 2 Bolt Lower Internal StemAttach lower internal stem to base plate using six (6) stem bolts. Once attached, twoCOUNTERSUNK HOLES on the lower internal stem will line up in the direction of theprimary mast and boom position. If base plate is not set using tapped holes for alignment,the internal stem will not line up properly. See above diagram. Make sure bolts are verytight.
STEP 3 Bolt Upper Internal StemSlide acetal ring over lower internal stem. Slide upper internal stem over lower internalstem. Bolt (4) locator screws and washers (included with umbrella) to lower stem.
Refer to umbrella manual for further installation instructions.
A B C D
IN-GROUND FITTING KIT
VERY IMPORTANT: To achieve the exact desired position of the Galaxy canopy (when inthe open position or a perfectly symmetrical multiple Galaxy installation, it is imperative thatthe installation fitting be aligned correctly. Please follow the detailed instructions below.
The Galaxy In-Ground Fitting has six (6) tapped holes to accept six (6) stem bolts.
STEP 1 PreparationThe in-ground fitting needs concreting in the ground per the diagram. The hole sizerecommended assumes the terrain is thick clay. Should the terrain be fine soil or sand,the hole size should be increased. Make sure two TAPPED HOLES are lined up in thedirection of the desired primary mast and boom position. You must align two TAPPEDHOLES to achieve the desired position.
STEP 2 Bolt Lower Internal StemOnce installed and the concrete has cured, bolt the lower internal stem to in-ground fittingusing the six (6) stem bolts. Once attached, two COUNTERSUNK HOLES on the internalstem will line up in the direction of the primary mast and boom position. If in-ground fitting isnot set using tapped holes for alignment, the internal stem will not line up properly. Seediagram above. Make sure bolts are very tight.
STEP 3 Bolt Upper Internal StemSlide acetal ring over lower internal stem. Slide upper internal stem over lower internalstem. Bolt (4) locator screws and washers (included with umbrella) to lower stem.
Refer to umbrella manual for further installation instructions.
IMPORTANT: When concreting the in-ground fitting in place, make sure not to get slurry inthe screw threads. Either apply tape over the holes on both sides of the fitting or place thestem bolts in the threads and withdraw them with the concrete is set. Make sure that the in-ground fitting is perfectly level. Allow the concrete to cure for the appropriate cure time foryour area before installing the stem onto the fitting.
In-Ground Fitting Kit includes:A - Stem Bolts (6)B - Allen WrenchC - In-Ground Fitting
A B Stem Bolts
ConcreteFooting
In-GroundFitting
Flare at bottom
Ground Level300mm
800mm
800m
m1.
2m
UpperInternal Stem
UpperInternal Stem
Concrete
Holes forExcalibur Bolts
Base Plate
Acetal Ring Acetal Ring
Locator Screws& Washers
Locator Screws& Washers
Stem BoltsLowerInternal Stem
LowerInternal Stem
C
Stem Bolts
ConcreteFooting
In-GroundFitting
Flare at bottom
Ground Level300mm
800mm
800m
m1.
2m
UpperInternal Stem
UpperInternal Stem
Concrete
Holes forExcalibur Bolts
Base Plate
Acetal Ring Acetal Ring
Locator Screws& Washers
Locator Screws& Washers
Stem BoltsLowerInternal Stem
LowerInternal Stem
Approximately 0.3m3 of concrete requiredassuming the terrain is thick clay. Fine soilrequires appoximately 0.5m3/750kg.Recommend (6) steel bars, length 1.0m
Concrete Mount Kit includes:A - Base PlateB - Stem Bolts (6)C- Excalibur Bolts - (6) 014x150mm - NOT INCLUDEDD - Allen Wrench
21
CONCRETE MOUNT KIT
VERY IMPORTANT: To achieve the exact desired position of the Galaxy canopy (when inthe open position or a perfectly symmetrical multiple Galaxy installation, it is imperative thatthe installation fitting be aligned correctly. Please follow the detailed instructions below.
The Galaxy Concrete Mount Kit has twelve (12) holes, six (6) are countersunk for bolting tothe concrete patio, and the other six (6) are tapped to accept the stem bolts.
STEP 1 Bolt Base PlateBolt base plate to concrete using six (6) 014x150mm Excalibur bolts (not included), makingsure two TAPPED HOLES are lined up in the direction of the desired primary mast andboom position. The countersunk holes are used for bolting to the concrete but should notbe used for alignment. You must align two TAPPED HOLES to achieve the desired position.
STEP 2 Bolt Lower Internal StemAttach lower internal stem to base plate using six (6) stem bolts. Once attached, twoCOUNTERSUNK HOLES on the lower internal stem will line up in the direction of theprimary mast and boom position. If base plate is not set using tapped holes for alignment,the internal stem will not line up properly. See above diagram. Make sure bolts are verytight.
STEP 3 Bolt Upper Internal StemSlide acetal ring over lower internal stem. Slide upper internal stem over lower internalstem. Bolt (4) locator screws and washers (included with umbrella) to lower stem.
Refer to umbrella manual for further installation instructions.
A B C D
IN-GROUND FITTING KIT
VERY IMPORTANT: To achieve the exact desired position of the Galaxy canopy (when inthe open position or a perfectly symmetrical multiple Galaxy installation, it is imperative thatthe installation fitting be aligned correctly. Please follow the detailed instructions below.
The Galaxy In-Ground Fitting has six (6) tapped holes to accept six (6) stem bolts.
STEP 1 PreparationThe in-ground fitting needs concreting in the ground per the diagram. The hole sizerecommended assumes the terrain is thick clay. Should the terrain be fine soil or sand,the hole size should be increased. Make sure two TAPPED HOLES are lined up in thedirection of the desired primary mast and boom position. You must align two TAPPEDHOLES to achieve the desired position.
STEP 2 Bolt Lower Internal StemOnce installed and the concrete has cured, bolt the lower internal stem to in-ground fittingusing the six (6) stem bolts. Once attached, two COUNTERSUNK HOLES on the internalstem will line up in the direction of the primary mast and boom position. If in-ground fitting isnot set using tapped holes for alignment, the internal stem will not line up properly. Seediagram above. Make sure bolts are very tight.
STEP 3 Bolt Upper Internal StemSlide acetal ring over lower internal stem. Slide upper internal stem over lower internalstem. Bolt (4) locator screws and washers (included with umbrella) to lower stem.
Refer to umbrella manual for further installation instructions.
IMPORTANT: When concreting the in-ground fitting in place, make sure not to get slurry inthe screw threads. Either apply tape over the holes on both sides of the fitting or place thestem bolts in the threads and withdraw them with the concrete is set. Make sure that the in-ground fitting is perfectly level. Allow the concrete to cure for the appropriate cure time foryour area before installing the stem onto the fitting.
In-Ground Fitting Kit includes:A - Stem Bolts (6)B - Allen WrenchC - In-Ground Fitting
A B Stem Bolts
ConcreteFooting
In-GroundFitting
Flare at bottom
Ground Level300mm
800mm
800m
m1.
2m
UpperInternal Stem
UpperInternal Stem
Concrete
Holes forExcalibur Bolts
Base Plate
Acetal Ring Acetal Ring
Locator Screws& Washers
Locator Screws& Washers
Stem BoltsLowerInternal Stem
LowerInternal Stem
C
Stem Bolts
ConcreteFooting
In-GroundFitting
Flare at bottom
Ground Level300mm
800mm
800m
m1.
2m
UpperInternal Stem
UpperInternal Stem
Concrete
Holes forExcalibur Bolts
Base Plate
Acetal Ring Acetal Ring
Locator Screws& Washers
Locator Screws& Washers
Stem BoltsLowerInternal Stem
LowerInternal Stem
Approximately 0.3m3 of concrete requiredassuming the terrain is thick clay. Fine soilrequires appoximately 0.5m3/750kg.Recommend (6) steel bars, length 1.0m
13401 Brooks DriveBaldwin Park, CA 91706p 626.338.8810f [email protected]
shademakerusa.com
© 2015 Shademaker. All rights reserved. SMOG-GMK-115