Front Panel Programming - itrbo.com screen.pdf · Generic Option Board Installation Initilal Setup...
Transcript of Front Panel Programming - itrbo.com screen.pdf · Generic Option Board Installation Initilal Setup...
< 447.7000A >< 447.7000A >Edit channel 1Edit channel 1
< 447.7000A >< 447.7000A >< 447.7000A >< 447.7000A >
Select TypeSelect Type< Digital >< Digital >< Digital >< Digital >
Tx FrequencyTx Frequency403.0000 MHz403.0000 MHz
Front Panel ProgrammingUser’s Guide
http://www.itrbo.com/version 1.1
Generic Option Board Installation
Initilal Setup with MOTOTRBO CPS
Option Updater Software Installation
Front Panel Programming Instructions
3
6
11
17
Contents
Generic Option Board Installation
1
2
3
Remove precisionscrews
Gently lift upward
Disconnect keyboard
4
5
6
Remove screws
Install Generic Option Board
Reassemble the radio by reversing the preceding steps.Don’t forget to reconnect the keyboard.
Initial Setup with MOTOTRBO CPS
MOTOTRBO CPS must be installed and working in order to create a zone and channels required by the Front Panel Programming software.
To begin, connect your radio to your computer usingthe USB programming cable. Start MOTOTRBO CPSand follow the instructions shown on the followingpages.
Click “Read” in the menu bar
Choose “Expert” modein the “View” menu
Right-click “Channels”to add a new Zone
Right-click your newly created zone and exactly oneanalog channel and exactly one digital channel.
The “Option Board” check boxmust be enabled for both channels
Right-click the zone and rename it to “FPP”
First, add an analogchannel. This mustbe added before thedigital channel is added.
Then add a digitalchannel.
Click “Write” in the menu bar
Allow the programming to complete
To complete this stage of the setup process, poweryour radio o�, then on again.
Option Updater Software
Option Update Setup Wizard
Option Update Setup Wizard
Option Update Setup Wizard
Option Update Setup Wizard
Connect your radio to your PCwith the USB programming cable, then click “Scan radios”
Choose “File” - “Select image...”and locate the HEX update �lefound in the Option Update installation folder.
Once programming is complete,turn the radio o�, then on again.
Loading the Front Panel Programming HEX �le ontothe radio.
Front Panel Programming Instructions
To enter Front Panel Programming mode on yourradio, select your newly created zone. Using theknobs and keypad on your radio:
Press the “menu” buttonPress the right arrow button twicePress the “OK” button
Use the arrow buttons to navigate to your newly created zone, then press the “OK” button
Enter LicenseEnter License0000000000
OK
Press and hold for 2 seconds,
Use the numeric keypad to enter your 10 digit license key. Press the ‘OK’ button when done.
You are now in communicationsmode.
Listen and talk from this screen.
Press ‘#’ to enter FPP configuration.
OK
then press
You are now in communicationsmode.
Listen and talk from this screen.
Ch1 ---.----
back
The PIN exists to prevent accidentalprogramming. Enter ‘1234’ with the keypad, then press the ‘OK’ button.
OK
The PIN exists to prevent accidentalprogramming. Enter ‘1234’ with the keypad, then press the ‘OK’ button.
Enter PINEnter PIN1234
#
#
Edit channel 1Edit channel 1< 447.7000A >
OK
Choose the channel you would liketo configure using the left & right arrow buttons, then press ‘OK’
Select the signal type. Press ‘OK’ to continue.
Enter the Rx frequency using thenumeric keypad, then press the ‘OK’ button
Rx FrequencyRx Frequency403.0000 MHz
Select the signal type. Press ‘OK’ to continue.Select TypeSelect Type
< Digital >
Enter the Tx frequency, then press the ‘OK’ button.Enter the Tx frequency, then press the ‘OK’ button.Tx FrequencyTx Frequency
403.0000 MHz
OK
OK
OK
Programming Digital Channels
The following screen varies,depending on Call Type
Color CodeColor Code< 3 >
OK
Choose the color code you would like using the left & right arrow buttons, then press ‘OK’
Choose ‘timeslot 1’ or ‘timeslot 2’using the arrow buttons, then press ‘OK
Choose ‘timeslot 1’ or ‘timeslot 2’using the arrow buttons, then press ‘OK
TimeslotTimeslot< Slot 1 >
OK
Choose the call type: Group Call Private Call All Call
Choose the call type:
Private Call All Call
Call TypeCall Type< Group Call >
OK
Enter the Tx frequency, then pressthe ‘OK’ button.Enter the Tx frequency, then pressthe ‘OK’ button.TalkgroupTalkgroup
00000000
OK
SavingSavingChannel 1
Programming Complete
Edit channel 1Edit channel 1< 447.7000A >
OK
Choose the channel you would liketo configure using the left & right arrow buttons, then press ‘OK’
Select the signal type. Press ‘OK’ to continue.
Enter the Rx frequency using thenumeric keypad, then press the ‘OK’ button
Rx FrequencyRx Frequency403.0000 MHz
Select the signal type. Press ‘OK’ to continue.Select TypeSelect Type
< Analog 12.5 >
Enter the Tx frequency, then press the ‘OK’ button.Enter the Tx frequency, then press the ‘OK’ button.Tx FrequencyTx Frequency
403.0000 MHz
OK
OK
OK
Programming Analog Channels
Rx ToneRx Tone< PL >
OK
PL DPL CSQ
Rx PL ToneRx PL Tone067.0
OK
Tx ToneTx Tone< PL >
OK
PL DPL CSQ
Tx PL ToneTx PL Tone067.0
OK
SavingSavingChannel 1
Programming Complete
Enter the Rx PL Tone using thenumeric keypad, then press the ‘OK’ button
Enter the Tx PL Tone using thenumeric keypad, then press the ‘OK’ button