Delphi Automotive Design Feature In-Vehicle Breathalyzer ...
For Vehicle Repair Workshops and the Automotive Industry ... kalusto.pdf · For Vehicle Repair...
Transcript of For Vehicle Repair Workshops and the Automotive Industry ... kalusto.pdf · For Vehicle Repair...
ISS
UE
1 -
20
11
/ 0
4
For Vehicle Repair Workshops and the Automotive Industry
1
DThe chassis adjuster is a practical assembly aid when performing repair work or replacing parts of the steering and chassis of commercial vehicles.The tool was developed specifically for use on vans, trucks, buses, trailers and semi-trailers. The task of the tool is basically to return the wheel varia-bles, such as the camber and track, back to their original state as accurately as possible in a simple and professio-nal way after being repaired.
Advantages:- Easy installation, easy use and short fitting time- Universal use, regardless of hole distance or number of bolts- Optimization of the repair procedure by eliminating unnecessary axle measurement with non-existent, irregular tire wear. - Cost-effective repair / competitive advantage - One-man operation / independent of network and measurement station
A1
For Vehicle Repair Workshops and the Automotive Industry
→ New AdBlue Refractometer / Coolant / Battery Acid Page 6
→ Problem solver ball joint puller „VIBRO-IMPACT“ Page 8
→ Innovation Torch Cree Power Page 16
→ Top value power bit set Page 12
Replacement of tie rod ends without axle measurement!
Application areas, e.g.:- Replacement of chassis components, especially steering parts, e.g.: Tie rod end (ball joint) / tie rod tube / trackrod and push rod / axial joints etc.
Scope of supply:2 x universal scissor mount2 x laser units incl. batteries4 x discs with reducing collar M144 x discs with reducing collar M164 x nuts with reducing collar M184 x nuts with reducing collar M201 x Roll Fixpoint stickers
150.1810 trucks+transporters, 21 pcs., for bolts M14-M22
ISS
UE
1 -
20
11
/ 0
4
2
For Vehicle Repair Workshops and the Automotive Industry
Working method:Before starting repairs, a fixed marking is applied to the projection surface (e.g. wall, floor, wheel arch, etc.) using masking tape, with the aid of both lasers. The fixed point! This designates the initial position before the repair and will be made on the driver and passen-ger side in event of intervention in the track position (e.g. changing the track-rod end). After repairing, the laser points are repositioned so that they correspond precisely with the markings on the driver and passen-ger sides by, e.g. turning the new track-rod end in and out. When intervening in the track position, for examp-le, the marking of the side not repaired always serves as a reference mark.
Methods from everyday repair and disadvantages
The track gauge: - Second man required- High purchase price
Length adjustment: - Lay tie rods side by side or measurement with ruler- Very inaccurate - no exact reference point
Axle measurement:- High repair cost for the customer- Time consuming- Not needed when previously no irregular tire wear existed
Function and characteristics Universal scissor mountAdjustment to bolt or hole distancePosition either to the inside or outside
Use for M14 to M22
Precise adaptationConnection collar for optimal centeringCone holder for nuts + wheel bolts
Laser unit with depth adjustment Ball stop in 4 stepsFixation over knurled wheel
Disc with reducing collar
M14
Disc with reducing collar M16
Original holder for M22
- Raise the vehicle slightly until wheels rotate almost freely- Dismantle protective steel ring on the rim- Remove the second nut for fastening the scissor mount- Screw Fixpoint to the rim (about 12 o‘clock position)- Fixed points set by using laser and label on a projection surface
Caution: Do not lift or lower vehicle- Replace tie rod end or entire tie rod- Install new or replacement parts - clamping device remains loosened- Tighten pivot pin- By steering wheel to one side (preferably to non-repair side) bring laser in the marking
- Now adjust the opposite side by turning the tie rod until laser spot is at the centre of the sticker.
- Repeated check of the first side and possible slight readjustment- Finally, the two laser points must again be at the centre of the respective Fixpoint stickers
Nut with reducing collar M20
Notes:The use of the chassis adjuster is not a replacement for axle alignment, especially not if before the repair irregular tire wear was apparent. However, in most cases exact adjustment made with the chassis adjuster is entirely sufficient to guarantee the axle to function perfectly, just like before repairs.
Nut with reducing collar
M18
Part replaced - track adjusted
State before the repair
Condition after the repair
ISS
UE
1 -
20
11
/ 0
4
For Vehicle Repair Workshops and the Automotive Industry
3
516.1493 Torque Wrench 3/4", 200-750N•m, including enlarging mushroom head 1"- Excellent for use in tightening truck wheels, e.g.- Inspected and supplied with certificate according to DIN EN ISO 6789, traceable to national standards / accuracy ± 3% of the set scale value- Supplied with mushroom 1"x 1" for conversion to large drives, thus significantly greater scope of use - Clearly audible and palpable release signal after the desired torque value has been achieved / slide roller bending mechanism- Overload guarantee of 125% of the maximum scale or torque value- Long service life
ANTICLOCKWISE FASTENING
CLOCKWISE FASTENING
516.3700 Universal Torque Multipliers 3/4", 1300N•m- For use with a torque wrench- With single-stage, ball-bearing precision planetary gear- Supplied with two support devices for flexible use - Female square drive according to DIN 3120 / ISO 1174 with ball stopAdvantages:- Transmission of maximum torque with minimum use of force- Multiplies human strength and minimizes risk of injury- Protects nuts and bolts through smooth transmission- No long lever needed- Robust design for maximum torque- For a defined input torque, we recommend combined use with KS torque wrenchesTechnical data:Input / Output: 1/2" / 3/4"Input torque max: 260N•mOutput torque max: 1,300N•mGear ratio: 1:5L = Total length: 395mmD = Head diameter: 110mmH = Height: 127mmWeight: 4,200gScope of supply:1 x power transmission spanner1 x bearing support straight1 x bearing support angleSupplied in sheet steel case
516.1197 Angle Measuring Disc 3/4 ", with magnet- For professional, angle-controlled angular fastening of screws with a fixed target marker- Since a defined pretightening torque must always be applied first, using a torque wrench is recommended- Universal fixation to the fixed point through a flexible magnetic arm- Female square drive according to DIN 3120 / ISO 1174 with ball stopTechnical data:Working range: 0° - 360°Scale division: 2°Scale diameter: 87mmHeight: 87mmTotal length: 624mmdrive/intake: 3/4” inside x 3/4” outside
3/4“max.
1300N•m
1/2“max.260N•m
3/4“max.
1300N•m
1/2“max.260N•m
200- 750 N•m
Drive N•m Lbf•ft Scale division
Lengthmm
Head - Ømm
Head height mm
200 - 750 150 - 550 10,0 1250 69 33 48003/4"
mitPrüfzertifikat
ZertifikatGenauigkeit
+/-3%
DIN EN ISO 6789
Ratchet head:Ratchet head polished with robust 30-tooth mechanismControlled clockwise and anticlockwise useChange the direction of rotation by simply rotating the mushroom head
Serial number:Individual serial number for unique product identification
Main scale:Generously dimensioned window with magnifying glassGraduation in N•m and Lbf•ft
Handle:The ergonomic, two-component handle
guarantees safe and fatigue-free working
Setting fixing:A blue ring on the slide-in knob that you can see through the
finger grips indicates: „Important: Fix the setting“Fix the torque setting by pressing in the slide-in knob
Micrometer scale:Micrometer scale ring for fine setting
Generously dimensioned window with magnifying glass
Corrosion:Steel tube body, powder-coated
Highest accuracy =
± 5 % tolerance
3/4" 1"
Nut with reducing collar M20
ISS
UE
1 -
20
11
/ 0
4
4
For Vehicle Repair Workshops and the Automotive Industry
550.5410 + 550.5415 BASICplus Videoscope Set Ø 5.5 mm
550.5090 BASICplus Videoscope Set Ø 6 mm with movable probe head (150°)
- 4 dimmable mini LED lamps- System is transportable and battery-powered- Probes are fundamentally bend-resistant as no fibre optic cables are used- Greatest possible field of vision thanks to the special camera in the probe head- Simple probe change thanks to the standardised adapter system- Very good picture and video quality- Image recording possible in JPEG format- Video recording in MPEG4 format- Viewing on large monitor with optional AV cable- Multilingual menu (14 languages)- Including chargeable Li-polymer battery 3.7 V- Robust 2-component housing protects against light shocks.- Delivered in a sturdy plastic case
With 2-fold bending- Viewing direction of the camera head infinitely adjustable in two directions, each 150°, using a rotary button on the transmitting device- Locking function of the viewing angle using the locking switch on the transmitting device- Mirrors do not have to be used due to swivelling probe head- 4 dimmable mini LED lamps- System is transportable and battery-powered- Probes are fundamentally bend-resistant as no fibre optic cables are used- Greatest possible field of vision thanks to the special camera in the probe head- Very good picture and video quality- Image recording possible in JPEG format- Video recording in MPEG4 format- Viewing on a TV with optional AV cable possible- Multilingual menu (14 languages)- Including chargeable Li-polymer battery 3.7 V- Dual component housing of the basic device protects against slight impacts- Includes alcohol cleaning set- Delivered in a sturdy plastic case
1 m
5,5 mm 550.5410
Ø
1 m
5,5 mm 550.5415
Ø
Probe semi-rigid 90° side camera
With movable PVC cover front camera
Semi-rigid probe 0° front camera with 90° mirror attachment
Hand-held unit technical data:Weight: 340 gScreen: 3.5" (TFT LCD)Output format: NTSC and PALStill picture storage format: JPEG (640 x 480)Frame rate: ~ 30 bpsCompression format: MPEG4Storage medium: SD card up to max. 2 GBMonitor: 16.7 million coloursBatteries: Li-Polymer 3.7 V (AC 100-240 V / 50-60 Hz)Power consumption: DC 5.5 - 1.8 Aapprox: 4 hours with fully charged batteryOperating temperature: -10°C to +60°C
Hand-held unit technical data:Weight: 340 gScreen: 3.5" (TFT LCD)Output format: NTSC and PALStill picture storage format: JPEG (640 x 480)Frame rate: ~ 30 bpsCompression format: MPEG4Storage medium: SD card up to max. 2 GBMonitor: 16.7 million coloursBatteries: Li-Polymer 3.7 V (AC 100-240 V / 50-60 Hz)Power consumption: DC 5.5 - 1.8 Aapprox: 4 hours with fully charged batteryOperating temperature: -10°C to +60°CScope of supply:- Basic device- Probe with a movable probe head- Mains charger- 1 GB SD memory card- Alcohol-cleaning kit- Delivered in a sturdy plastic case
Prob
e head with LED
5,5 mm
Scope of supply:- Basic device- Mains charger- 1 GB SD memory card- Alcohol-cleaning kit- Sample probe- 550.5410 with 90° mirror attachment
Fixation in working position
Probe head 150°rotatable
Head movement via hand wheel
On/Off switch with dimmer function
Prob
e head with LED
6 mm
1 m
6 mm 550.5090
Ø
ISS
UE
1 -
20
11
/ 0
4
For Vehicle Repair Workshops and the Automotive Industry
5
455.0000 Pressure Screw Stud Socket Set, 4-pcs.Assortment for fitting and dismounting pressure screws on nozzle holders. Includes 4 special designs for all possible uses.1. Standard version2. Version with fixing screw for non-slip fitting and dismounting.3. Tube for feedthrough of the cable from the needle motion sensor on the first cylinder4. Semi-open versionConsists of:1 x Type1: 1/2" x 4 stud x L=72mm1 x Type2: SW32 x 4 stud x L=70mm, with fixing screw M14 (SW22)1 x Type3: SW32 x 4 stud x L=122mm, for needle motion sensor1 x Type4: 1/2" x 3 stud x L=121mm, milled openApplication:MB and MAN-Euro 2 motors e.g. OM 401-404, 403/423, 407, 409 h/hA, 421-424, 441-444/LA,A, 427, 429, 447/h/hA , M 470h
Piston ring clamp,Ø 45 -175mmTo prestress the piston rings when inserting the piston into the cylinder.Spring band steel version - infinitely adjustable with the actuating tool.
Piston Ring Pliers, Ø 50-160mmSpecial pliers for safe and professional placement of piston rings.The special design prevents the fracture or the dislocation of the piston ringMatt chrome finish with plastic handles.
150.1210 Valve spring compressor- Tool for tightening the valve springs when changing the valve stem seals without having to remove the cylinder head- Slim design allows universal application- Easily operated by handwheelApplication:Car, van and Commercial vehicle engines
455.0016 Cylinder Head Wrench MAN, 1/2", TX E20- For mounting and dismounting cylinder head bolts on MAN commercial vehicles without removing the injector nozzle and lines- Use e.g. in the series MAN F2000 / F90 / F8 and MAN buses with D25 and D28 engines- Cr-Mo power version with Matt Chrome FinishTechnical data:Wrench width: Torx E20Actuator: 1/2"Length: 165mm
455.0005 Serrated-tooth socket 58 tooth, for pre-chambers - Special socket tool for fitting and dismounting pre-chamber lock rings on MB Diesel Engines- Special steel - surface phosphatedApplication:Truck: OM 601 - 602 - 603 - 604 - 605 - 24 mmCar: W 124 - 201 (from year 90) - 202Technical data:Length: 60mmNumber of teeth: 58Actuator: 1/2"
Ø mm Ø H mm
150.1141 45 - 90 1.3/4" - 3.1/2" 50,0 158
150.1142 57 - 125 2.1/4" - 5" 100,0 300
150.1143 90 - 175 3.1/2" - 7" 100,0 340
150.1144 90 - 175 3.1/2" - 7" 165,0 555
Ø mm A mm D mm L mm
150.1175 50,0-110,0 0,0-110,0 60,0 210,0 305
150.1176 80,0 - 120,0 0,0-120,0 60,0 220,0 340
150.1177 110,0 - 160,0 0,0-158,0 60,0 280,0 445
130
mm
1/2"
ISS
UE
1 -
20
11
/ 0
4
6
For Vehicle Repair Workshops and the Automotive Industry
150.1480 Automotive Multimeter including test probes and crocodile clips- Solid multimeter with all standard measurement functions- Central rotary switch for quick selection of the desired measurement function- Large, 3-3/4-digit and illuminated display with digital and bar graph (including battery indicator)- All 4 input terminals are protected against overload- Comes with fold-out, two way adjustable stand with protective rubber holsterMeasurement functions:- continuity test (with audible signal)- Transistor tester- diode test (with audible signal)- capacity- frequency measurement- data hold function- automatic measuring range selectionTechnical data:DC: 326 mV to 1000 VDC: 326 mA to 10 AAC: 3.26 V to 750 VAC: 326 mA to 10 AResistance: 326 ohms to 32.6 MOhmCapacity: 0 to 32.6 uFFrequency: 10 Hz - 200 kHzMeasurements: 189 x 91 x 31 mmWeight: 310gPower supply: 9V batteryConsists of:1 x multimeter1 x measurement cable set with probe (red/black)1 x measurement cable set with crocodile clips (red / black)1 x 9V Bock battery
- Laser measuring gun for contactless temperature measurements (surface temperature) through the infrared radiation of a body- Pilot beam (red laser) for better orientation, can be switched on and off- Digital display / illuminated display- Automatic shut-off functionSample applications:Rotating engines / hard to reach points / liquid media / live cables / heating, gas and air-conditioning systems / cooling systems / hot brakes on passenger cars / commercial vehicles / trailers / aggressive chemicals / foodstuff / exhaust manifolds / glow plugs / detection of cold spots, etc.
550.1285 AdBlue Refractometer / Coolant / Battery Acid / Antifreeze- Optical precision test device for rapid analysis of liquids- A device for all common liquids in the automotive sector- With this device can also determine the urea content of AdBlue and therefore whether and when a change is necessary- Indispensable to ensure the optimal functionality of SCR -systems (selective catalytic reduction), since AdBlue layered or not used in the vehicle loses its desired properties- A very small amount (pipette) of the liquid is already enough to reach a definite measurement result- Use wherever liquids are delivered, stored and tested- Version with ATC (Automatic Temperature Compensation / 10°-30°C)Scale / Measuring Range / Resolution:Left scale single: Tests battery acid concentration Range 1,100-1,300 sg / Resolution: 0.01 sgMiddle scale, two parts: Antifreeze based on propylene glycol G13 Measuring range -25° C to -50° C / Resolution: 5°C Antifreeze based on ethylene glycol G11/G12 Measuring range -25° C to -50° C / Resolution: 5°CRight scale above single: AdBlue (VRA) urea content Measuring range from 30% to 35% / Resolution: 0.1%Right scale below single: Anti-freeze windshield washer fluid SRF1 Measuring range -10 to -40° C / Resolution 1°CConsists of:1 x refractometer1 x calibrating screwdriver2 x pipettesSupplied in a case with foam inlay
550.1289 AdBlue Urea Service Keys, SW 45.5 mmRequired for mounting and dismounting the lid on urea filter element. Ideal for hidden filter element between urea tank and metering valve. With the help of the 3/8" actuator, precise tightening (23Nm) is possible.Application:MB trucks e.g. new Actros, Atego, Axor, EONICTechnical data:Size: SW 45.5 mmActuator: 3/8" squareLength: 65mm
550.1683 Automatic Battery Fill Bottle 1 litre- This filler bottle is used to refill distilled water as part of battery maintenance work- Made of acid, oil and solvent-resistant plastic- The built-in special valve in the bottle head automatically stops the flow once the desired filling level is reached on the plates
Battery display Scan/Hold display
°C/°F display
Laser On/Off switchover button
Laser On/Off indicator
Digital display
Switchover button °C/°F
Applicable for, e.g.:Automotive area / Construction / Industry / Chemical and foodstuff monitoring, etc.Technical data:Switchable: °C / °FMeasuring range: -50 to +550 °C Emissivity: fixed at 0.95Power supply: 9V Bock battery (enough for approx.16h)EM ratio 8:1 (E=Distance / M=Measuring area)
1 litre capacity
150.3040 Infrared Thermometer
ISS
UE
1 -
20
11
/ 0
4
For Vehicle Repair Workshops and the Automotive Industry
7
450.0190 Vario Nuts and Cap Wrench Set, 14 pcs., heavy design- Extremely versatile universal wrench- New, heavy design for high power requirements- Secure hold by teeth of inner jaw and fixation by threaded spindle- Tension chain also ensures slip-proof work- Precise torque tightening possible with 3/4" square driveAdvantages:- Saves the purchase of many expensive special wrenches- No loss of time in purchase or building makeshift oneself- Minimization of the risk of injury from possible use of inappropriate materials- User is always able to work on special drive profilesUse in practice:Components: Screws / Nuts / CapsProfile: 6-edge, 8-edge, groove and round nuts (e.g. two-and cross-hole)Working range: Depending on the type up to SW 145mmAreas of application: van / truck / equipment / agricultural machinery / municipal and forestry Eequipment, etc.Consists of:1 x basic unit with fixing device3 x adapter pair mount, round, Ø 6 / 8 / 10 mm3 x adapter pair mount, square, 6 / 8 / 10 mm1 x tension chain1 x measurement cable set with probe (red/black)1 x measurement cable set with crocodile clips (red / black)1 x 9V Bock battery
Power bit socket, TX E24- Special socket wrench with long design for external Torx profile- For wheel flange mounting screw TX E24 M181,5 on SAF-axles- Chrome-molybdenum design, impact wrench proof and phosphatedApplication:Standard and Turbo-wheel flange with Knorr, Wabco and Haldex disc brakeSF RB 9022 K / H / WSF RB 9019 K / W
SWTX L Ø
450.0454 3/4" E24 140,0 44,0 748
450.0484 1" E24 145,0 51,0 1068
450.0175 Locknut Wrench 3/4", 6-pin and guide tube, rear axle MAN TGA- Very robust design with high precision fit- Designed for high torque tightening and release - Extremely break-proof pins in the inner side- With square drive for accurate torque tightening- Guide tube ensures slip and tilt free useApplication:MAN TGA rear axle HY 1350Technical data:Number of pins: 6Width of pins: 11.5mmInner Ø pin: 117mmInner Ø wrench: 132mmOuter Ø wrench: 148mmHeight with guide tube: 158mmHeight without guide tube: 110mmGuide tube Ø: Outer 66mm x Inner 60mm Actuator: Outside hexagon SW 60 + inside square 3/4"
450.0170 Locknut Wrench 3/4", 6-pin, front axle MAN TGA- Very robust design with high precision fit- Designed for high tightening and loosening torques (about 1200Nm required) - Extremely break-proof pins in the inner side- With square drive for accurate torque tightening- Use for example on maintenance-free axle MAN F2000, and HA of Van Hool double articulated buses, etc.Application:MAN front axle V9-82L-01 (disc brakes + ABS)Technical data:Number of pins: 6Width of pins: 8.0mmInner Ø pin: 92.5mmInner Ø wrench: 100.5mmOuter Ø wrench: 110.0mmWrench height: 80.0mmActuator: 3/4" inside square + SW 60 outside hexagon
3/4" 1"3/4"
3/4" 3/4"
ISS
UE
1 -
20
11
/ 0
4
8
For Vehicle Repair Workshops and the Automotive Industry
Universal Ball Joint Extractor- Tool for pressing the conical joints of ball joints- With prong aperture 36mm for joints Ø 27 to 36mm- Proven, slim design and adjustable construction for high strains- Fine adjustment of parallelism of lever and fork over central set screw- Mechanical design (670.0131) with threaded spindle- Hydraulic design (670.0141) with 10t fat hydraulic spindle- Both versions also with threaded holes in the fork piece for optional use with oil-hydraulic flat cylinder until max.10t (KS 640.0140)- Universal application for vans + medium duty trucks, agricultural and municipal machinery etc.Applicable for, e.g.:MB Sprinter / Fiat Ducato / VW LT / Ford Transit etc.MB Atego up to 17t. / MAN / Iveco / Renault / Scania / Volvo / DAF etc.
980.1015 Grease Nipple Cleaner- Cleans belaboured grease nipples, slides and guides- Effectively dissolves old resinified grease, debris, dirt and rust- Therefore fresh grease can be easily re-pressed into the lubrication point - Supplied with flexible extension in plastic boxTechnical data:Grease nipple cleaning press:Length with coupling: 205 mmWeight: 365gThread: AG M10 x 1Adapter flexible:Length: 125 mmWeight: 65gThread: AG M10 x 1/ ID M10 x 1
450.0066 Ball Joint Puller „VIBRO-IMPACT“ with window, 39mm- Innovative, special design with window for universal use- Drop-forged from one piece, hardened and tempered- Robust, impact wrench proof trapezoidal threaded spindle- Pressure on the ball screw head reduces friction and centres the pullerAdvantages:- High releasing force in connection with impact wrenches through rotating impact stroke, making them especially effective with cone seats- The window ensures accessibility in steering levers with great material overhang (see application photo)- Small size - minimum space requirement- Use depending on available space also with manual drive toolsApplicable for, e.g.:Universally in the truck sector e.g. SCANIA, MB, MAN, HINO (e.g. 414 drag link), etc.Technical data:Spindle Ø: Tr-26mmSpindle length: 128mmWeight: 2,132g
450.0085 Suspension Joint Pin Extractor, Sprinter+LT- This tool is needed to loosen the suspension joint pin from the conical seat of the axle - This particularly solid design is angled back and can thus be ideally placed between the suspension arm and axle body- The ball fastened on to the spindle drive (SW24) also allows the application of a targeted blow to assist in loosening- The centering point for the trapezoidal thread spindle M27 is mounted on ball bearings- For extremely fixed pins, there is the possibility of retrofitting a 10t hydraulic spindle (holder 1-1/2"x16 threads, e.g. KS 700.1400-1)Applicable for, e.g.: VW LT, MB Sprinter
Amm
Cmm
maxt
SWmm
Spindle mm
670.0131 36 90 10 22 G1/2" x 14g x 110 3,70
670.0141 36 90 10 17 1.1/2"x16G 4,70
Drive spindle can be used either in the lever or fork depending on space
ISS
UE
1 -
20
11
/ 0
4
For Vehicle Repair Workshops and the Automotive Industry
9
max. clamping depth mm max. clamping width mm
145.0301 80,0 160,0 0,50
145.0311 120,0 250,0 1,23
145.0312 120,0 300,0 1,70
145.0320 120,0 400,0 1,91
145.0322 120,0 600,0 2,33
145.0324 120,0 1000,0 3,75
Amm
Lmm
Smm
0,0 - 60,0 250,0 27,5 0,52
450.0090 Drift Pin Set for commercial vehicles, 4-pc.- High-quality and massive drift set for daily use in truck, construction equipment and agricultural machinery workshops- Ideal for driving out split pins, bolts, bearing rings, but can also be used for centring boreholes- Design with high-alloy steel with hexagon shaft and conically- tapered tip- Heavy-duty impact head - regrindable
156.0598 Rolling Head Pry Bar, 1800mm, heavy design- Extra long and massive crowbar for heavy use in truck, construction equipment and agricultural machinery plants- Good positioning also with narrow working gap due to rolling head with ground and hardened blade end- Dimensionally stable square shaft with pointed and hardened end
All-steel screw clamps with toggle, 160-1000mm- Ideal for steel and vehicle construction- High clamping force through double-T profile rail with back toothing- Tempered fixed and sliding arm for resilient and elastic tension - High safety through linear transmission at sliding arm- Robust trapezoidal threaded spindle with movable pressure plate- Insertable clamp handle with rounded ends
115.1033 Grip Pliers, L=250mmIdeal for welding in vehicle construction- Forged and serrated jaws- Jaw width adjustable over knurled wheel- Good handling with quick-release and locking levers- Grips reliably round and flat materials- Chrome-vanadium design - nickel plated
D1mm
D2mm
Lmm
Smm
22,0 35,0 1800 37,0 10,00
1800
mm
Ø mm L mm
6,4 300,0 390
6,4 380,0 730
8,0 300,0 410
13,0 460,0 1310
Optimal base -
highest leverage
ISS
UE
1 -
20
11
/ 0
4
10
For Vehicle Repair Workshops and the Automotive Industry
160.0720 Air Hydraulic Jack 22 t- Short and compact design - ideal for mobile use- Minimum underclearance depth (166mm) - secure stand - Easy to store with just 25kg weight and folding lever / lever can be locked in 3 positions 0° -90° -180°- Lifting, lowering, control and support function entirely by lever- Controlled lowering over manual dead man control- Overload protection through built-in safety valve - Supplied with V-shaped support 30mm and extension 100mm- The maximum hub height of 450mm is achieved solely by using the two supplied adapters.- Large, oil and acid resistant, solid rubber tiresTechnical data:A = length of lever: 578mmA1 = length of lever with Extension: 1,180mmB = Length: 470mmC = Height min: 166mmC = Height level 1 / max. 22t: 238mmC = Height level 2 / max. 8t: 320mm Stroke: 154mm Height max.: 450mmD = Width: 200mmE = Width including wheels: 270mm Capacity: 22/8 t
A1
A
B
C
ED
518.1155 Wheel Wrench, trucks- Socket wrench heads with hexagon profile- One side with 3/4" square drive for socket wrench inserts- Square drive acc. to DIN 3120 / ISO 1174 with ball stop- Dull satin finish - heads polished- Manufactured from chrome-vanadium-steel acc. to DIN 3319 / ISO 1174
Mechanics protection mat- Guarantees friendly and health-conscious work in the lower range of vehicles on a flat surface- Moisture and dirt resistant- Industrial clothing and knees remain dry, clean and warm - Insulated by a special 3-layer soft material- Petrol and oil resistant design with integrated handle- Universal and mobile use in repair shops, service and breakdown service vehicles
150.1995 Nut Cap Pliers, truck- Special pliers to remove caps on commercial vehicle wheel screw joints - Gentle and slip-proof working through insulation on the plier jaws- No scratches, no damage to nut caps, rims and trims- Handles dip-insulatedTechnical data:Jaw opening max. 60mmJaw depth: 72mm
160.0372 Quick-action steel axle standParticularly robust steel structure for securing and supporting loads- High stability due to four feet with base plate- For heavy vehicle weights- Solid cast steel load-bearing pile- 13-step manual quick adjustment using tension lever- Can be used in an optimum way combined with jacks- Supplied as a pairTechnical data:Max. load 12tMin. height: 480mmStroke: 250mmMax. height 730mmWeight: 26kgPedestal dimensions: 310x275mm
Max. load
capacity 12t
500.8045Mechanics Protection Mat, largeDimensions: D 1150 x W 550 x H 36mm
500.8040Mechanic Protection Mat, smallDimensions: D 480 x W 320 x H 36mm
SW 24
SW 32
SW 273/4"
250
mm
ISS
UE
1 -
20
11
/ 0
4
For Vehicle Repair Workshops and the Automotive Industry
11
515.3765 Pneumatic Impact Wrench with long spindle - High-performance double hammer - industrial striking mechanism- High-speed torque build, low vibration- Conveniently located release lever directly on the hand grip- Ambidextrous rotary knob for torque control with 4 settings- Separate switching lever (left / right)- With long spindle (230mm) suitable for deep-bed truck rims- Supplied including 1/2" coupler plugTechnical data:Clockwise-tightening torque: Level 1 = max. 1016 N•m Level 2 = max. 1694 N•m Level 3 = max. 2372 N•m Level 4 = max. 3388 N•mLeft run-release-torque: max. 4253 N•mIdle speed: 4200 RPMVibration: < 3.32 ms²Noise performance level: 114.7 dbANoise pressure level: 103.8 dbAAir consumption: 283 l/minOperating pressure: 6.3 bar (90 psi)
515.1215 Compressed Air Impact Wrench - High-performance double hammer - industrial striking mechanism- Lightweight and robust magnesium casing with soft-grip handle- Waste air discharge downwards through cold-absorbing handle - Switching lever (left / right) with 3-speed torque settings- Supplied including 1/4" coupler plugTechnical data:Clockwise-tightening torque: Level 1 = max. 444 N•m Level 2 = max. 592 N•m Level 3 = max. 810 N•mCounterclockwise-release-torque: max. 1,490 N•mIdle speed: 7500 RPMVibration: < 2.69 ms²Noise performance level: 104 dbANoise pressure level: 88 dbAAir consumption: 128 l/minOperating pressure: 6.3 bar (90 psi)
515.3010-A1 Die Grinder with HM case- Extremely versatile mini-pneumatic tool- Ideal for grinding, polishing and engraving work also in tight workspaces- Ultra-light, cold-absorbing casing with ergonomic design- Operating lever with safety lock / continuously adjustable mechanical speed regulation- Secure and precise machine guidance through vibration dampening- Clamping chuck 6mm for HM cutters, mini cutting discs and stone grinding heads- Supplied with 1/4" connector plug and adjustable exhaust air discharge HM cutter with 6mm admission shank- Staggered teeth for short-chipping materials- For deburring, edge breaking, plastering, welding and surface processing. - Quiet operation with maximum cutting edge stability and cutting performance - Versatile use in the repair sector for high-alloy, stainless, acid and heat resistant steels and cast iron - easily clamps also ball bearing material!Technical data:Power output: 330 WattIdle speed: 21000 RPMVibration: < 0.1 ms²Noise performance level: 95 dbANoise pressure level: 82 dbAAir consumption: 85 l/minOperating pressure: max 6.3 bar (90 psi)
Head-Ø Head height
Total length mm
Shaft-Ø Design
10,0 20,0 60,0 6,0 Shape A cylinder with spur toothing
10,0 20,0 60,0 6,0 Design G pointed arch
10,0 9,0 49,0 6,0 Design D spherical
Staggered teeth system
810N·m
3388N·m
B mm L mm
190,0 205,0 2,86
B mm L mm
230,0 600,0 16,20
1"
1/2"
ISS
UE
1 -
20
11
/ 0
4
12
For Vehicle Repair Workshops and the Automotive Industry
Power ball joints - Impact version for machinery operation- Phosphated chrome-molybdenum steel surface- Square drive according to DIN 3121 / ISO 1174- 1/2" design with ball stop- 3/4"+ 1" design for locking pinAdvantages:- Enormous expansion of the range of use of each impact wrench- Tight, spring-loaded ball joint - Ball joint works cleanly without tilting
Power-socket, L = 270 and 400mm - Impact version for machinery operation- Phosphated chrome-molybdenum steel surface- Extra-long version with hexagon profileAdvantages:- Protects the impact wrench - low wear- Direct frictional connection without any power loss- Causes enormous increase in releasing force of each 3/4" wrench- Easy reach of each wheel nut without extensionCaution:For dual tires on AP axles (from tire size 8 R 22.5), the 400mm version is needed.
450.0420 Power Bit Set, 16-pcs.- Extensive product range with many, very popular power socket types for the truck sector.- Impact version for machinery operation - Phosphated chrome-molybdenum steel surface- High savings compared to individual purchase of special nuts - Delivered in a sturdy plastic caseExamples of use:TX60 Actros brake discs, brake caliper, steering column leverTX70 DAF truck oil drain plug, MAN, DAF, MB HA-oil drain plugTX80 IVECO steering column lever, MAN steering TGATX100 IVECO steering column lever, MAN steering TGA Large Torx general bumper fixings e.g. MANE18 Torx cylinder head studs MAN M2000 model, coaches with D08 engineE20 Torx cylinder head studs MAN model F2000, F90, F8, buses with engines D25 / D28Torx E24 wheel flange screws SAF-axles (e.g. brake disc replacements)SW 14+17 brake pads/discs: UnimogSW 14 MB Actros, Citaro - axle types: HL7+HL8 Hypoid, Neoplan ZF-axle and MAN TGA wheel hubSW 17 MAN TGA + F2000 locking bolts upper suspension arm HA (4pcs)Consists of:4 x power bit insert hexagon socket, L=107mm SW 17 - 19 - 22 - 24mm4 x power bit insert Torx, L=107mm TX 60 - 70 - 80 - 90 - 1004 x power bit insert Torx E-Profile, L=107mm E18 x Ø24,0 - E20 x Ø24,0 - E22 x Ø25,8 - E24 x Ø27,81 x power bit socket adapter 3 / 4"x SW22, L = 52mm, length with inser 140mm 1 x power bit socket adapter 1 1"x SW22, L=59mm, length with insert 145mm
515.0610 Power Socket Set, short, 8-pc. - Impact version for machinery operation- Phosphated chrome-molybdenum steel surface- Short-standard version with hexagon profile According to DIN 3129 / ISO 2725-2- Delivered in a sturdy sheet steel caseApplications:trucks / trailers / construction / agricultural machinery etc.SW 29=1 1/8" for agricultural engineering (Case / John Deere, etc) Consists of:SW 27 - 29 - 30 -32 - 33 - 34 - 36 – 38
mmL
mmD1mm
D2mm
Tmm
515.1182 27,0 270,0 42,0 44,0 27,0 1,09
515.1183 30,0 270,0 46,0 44,0 30,0 1,14
515.1184 32,0 270,0 49,0 44,0 32,0 1,16
515.1191 27,0 400,0 42,0 44,0 27,0 1,25
515.1192 30,0 400,0 46,0 44,0 30,0 1,32
515.1193 32,0 400,0 49,0 44,0 32,0 1,36
515.1194 33,0 400,0 50,0 44,0 32,0 1,38
Lmm
Dmm
515.1133 1/2" 67,0 28,0 0,17
515.1374 3/4" 108,0 44,0 0,7
515.1801 1" 130,0 54,0 1,38
Sens
atio
nal O
ffer
1"
1/2" 3/4" 1"
3/4"
ISS
UE
1 -
20
11
/ 0
4
For Vehicle Repair Workshops and the Automotive Industry
13
Water Pump Pliers „Quattro-Gripp“- Innovative water pump pliers with automatic jaw adjustment- Maximum jaw opening approximately 40% over DIN ISO- Lightning-fast, almost continuous adjustment to the workpiece to be gripped due to innovative incremental adjustment- Push button with 4-tooth technology offers optimal support even with maximum use of force- 11-fold fine adjustment simply by pressing a button- Setting remains locked even after pliers have been opened- Precision box joint - ergonomic handle position- Drop-forged chrome vanadium steel for maximum strains
151.2150 Classic Ball End Hex Key Set,10-pc. - Extra long version, including SW 7 and up to SW 17 - DIN / ISO 2936- With ball head at the long end- Ideal for hard to reach screws - Special steel - satin chrome finish - through hardened Consists of:SW 3 - 4 - 5 - 6 - 7 - 8 - 10 - 12 - 14 - 17 mm
Length Jaw opening
115.8520 10" 250mm 50mm
115.8525 12.1/2" 320mm 75mm
115.8530 15.3/4" 400mm 85mm
113.2100 Corner Work Pipe Wrench Set, 3-pcs.- Classic corner work pipe wrench with slender S-shaped mouth- Optimal grip on the tube with 3-point system and teeth against direction of rotation- Infinitely adjustable and self clamping- Red powder coated - heads ground- Drop-forged and tempered Consists of:1 x Corner Work Pipe Wrench 1", 320mm1 x Corner Work Pipe Wrench 1.1/2", 420mm1 x Corner Work Pipe Wrench 2", 550mm
515.1003 Hand Impact Screwdriver Set, 11-pcs.Solid and good helper for releasing frozen screwsParticularly helpful in slot and Phillips head screws with conical heads, e.g. door hinges, brake discs and drums etc.Advantages:- Optimum feed, making the blade sit in the screw head through the hammer blow = impact bounce = releasing effect!- No slipping of the blade even using high forces- A minimal rotation of the head is also performed with the impact (Prabel mechanism)- Use either to loosen or tighten - The 1/2" drive can of course take any other bit socketConsists of:1 x hand impact screwdriver 1/2"1 x 5/16" power bit adapter 1/2" with clamping ring3 x power bit PHILLIPS®: PH1 - PH2 - PH36 x slotted power bit: 5.0 - 6.0 - 8.0 - 10.0 - 12.0 - 14.0 mm
Jaw with serrated diamond shape
Fine adjustment per „Drag and Drop“
Anti-pinching guard for safe working in every position
Compact and narrow pliers head
Chrome-vanadium steel, drop forged and tempered in oil
Nail & wire holder
Precision box joint
Ergonomic handle position, handles dip coated plastic
Double toothed gripping jaw / additionally inductive hardened gripping teeth
1.1/2"1.1/4" 2"
1/2"
Mouth opening
approximately
40% over ISO
ISS
UE
1 -
20
11
/ 0
4
14
For Vehicle Repair Workshops and the Automotive Industry
911.3490 Chromeplus® Telescopic Reversible Ratchet - Practical and solid 3/4" ratchet with telescopic extension- With recessed shift lever and robust 24-tooth ratchet mechanism- Quick-release function by pressing button on the ratchet head- Square drive acc. to DIN 3120 / ISO 1174 with ball stop- Knurled handle- Chrome vanadium / surface highly-polished chrome finishTechnical data:Head-Ø: 63mmHead height: 30mmLength min: 510mmLength max: 730mmWeight: 3,350g
Heavy Duty Box Spanner Set- Heavy duty design for high torque - For the safe release of large bolts and nuts - Box spanner head with 75° offset Flank Traction profile- Key shank with pipe holder and locking mechanism- Chrome vanadium Surface matt satin finish
Pipe extension for box spanner
517.9010 Heavy Duty Box Spanner Set Type 1, 4-pc.
mmA
mmB
mmD
mmH
mmL
mm
24 17,0 38,0 19,0 29,5 180,0 1 0,35
27 17,0 42,0 19,0 31,5 190,0 1 0,40
30 18,0 48,0 19,0 33,5 195,0 1 0,45
24 - 30 19,0 460,0 1 0,75
Pipe extension for box spanner
517.9015 Heavy Duty Box Spanner Set Type 2, 4-pc.
mmA
mmB
mmD
mmH
mmL
mm
32 18,0 49,0 22,0 34,0 200,0 2 0,55
36 18,0 49,0 22,0 34,0 200,0 2 0,65
41 20,0 54,0 22,0 35,5 205,0 2 0,75
32 - 41 22,0 610,0 2 1,25
Pipe extension for box spanner
517.9020 Heavy Duty Box Spanner Set Type 3, 4-pc.
mmA
mmB
mmD
mmH
mmL
mm
46 22,0 62,0 22,0 39,5 265,0 3 1,05
50 23,0 69,0 25,0 40,0 280,0 3 1,15
55 25,5 76,0 25,0 42,5 290,0 3 1,40
46 - 55 25,0 760,0 3 2,30
918.1801 Chromeplus® Flexible Socket Handle- Solid and a long lever with swivel head - Protects ratchets and torque wrenches from high impact- Removable, burnished swivel head - Square drive acc. to DIN 3120 / ISO 1174 with ball stop- Chrome vanadium / surface highly-polished chrome finishTechnical data:Head-Ø: 48mmHead height: 86mmLength: 1,030mmWeight: 3,800g
3/4"
3/4"
long lever - max.
releasing power
15°24
ISS
UE
1 -
20
11
/ 0
4
For Vehicle Repair Workshops and the Automotive Industry
15
Scope of supply:1/4" MODIFIX Mini T-handle swivel head ratchet1/4" Hexagon sockets 8, 10, 11, 12, 13 mm1/4" Adapter socket for 1/4" - C 6.3 bits1/4" Extension 50 mm
907.2210 Scraping Chisel Set, 4-pcs. High quality scraper assortment with continuous stainless steel blade- Two different models for different tasks - Model 1 = scraper with a thin, flexible and bendable blade - Model 2 = scraping chisel with dimensionally stable blade for stubborn gasket material, etc- Re-sharpenable blades are sharpened on one side diagonally- Ergonomic 2-component handle for slip-proof workingScope of supply:1 x scraping chisel 190x32x1,2mm1 x scraping chisel 165x32x2,5mm1 x scraping chisel 190x25x1,2mm1 x scraping chisel 165x25x2,5mm
917.0608
Socket Wrench Set with mini T-handle swivel head ratchet, 8-pcs.
838.7194 Roller Cabinet with 7 drawers, fitted with 7 system inserts- Sturdy sheet steel construction with 0.8 mm sheet thickness - torsion resistant- Ball bearing mounted drawer guide- Drawers can be pulled out 100%- Drawer compartments with with anti-slip rubber inlays- Work plate with 10 mm thick foam lining- With lateral metal handle- 2 wheels Ø 100 mm each- 2 Ø 100 mm steering wheels, with roller and rotary brake- Continuous lift rails- Electrostatically powder coated
Single-stage locking system:
- Central locking of all drawers using a cylinder lock
194 pieces
Consists of:BASICline BLACK/SILVER mobile workshop, with 7 drawersDrawer 1 1/4" SUPERLOCK socket wrench set, 46 pcs.1/2" SUPERLOCK socket wrench set , 24-pc.1/4"+3/8"+1/2"uni-bit+socket wrench set, 57-tlg.Drawer 2 Wrench Set, 35-pcs.
Drawer 3 1/3 deposit double ring spanner set, 4 pcs.ERGOTORQUE®max screwdriver set, 13-pcs.
Drawer 4Universal tool set, 15-pcs.
Load bearing capacity per drawer: 30 kgTotal load bearing capacity: 350 kg
1
2 4
3
3/2"
ISS
UE
1 -
20
11
/ 0
4
16
For Vehicle Repair Workshops and the Automotive Industry
Werkzeuge - Maschinen GmbH
01/2011 LL11-08E Sold only in specialist stores. Print mistakes, errors and technical alterations excepted. Prices valid up to 31.12.2011.
Seligenstädter Grund 10 - 12 D-63150 HeusenstammTelefon: +49(0) 61 04 49 74- 0Telefax: +49(0) 61 04 49 74-11e-mail: [email protected]://www.kstools.com
550.1237 Torch- Practical torch in pocket size for indoor and outdoor- With up to 130 lumens, it easily overshadows far larger torches- The light beam is adjustable from spot to floodlight- With just 130mm overall length, it fits easily in a backpack, glove compartment, bicycle bag or even in the mechanic‘s case or toolbox.- Shock-proof aluminium housing / protected from rain and spray- On/Off button with 4 modes: Light / Medium / Low / Flashing - Comes with handy grab strap with batteries
907.2105 Jackknife with lock function, in a belt bag- The ideal knife for all mechanics and warehouse employees- Blade with Teflon coating- Blade fixing folded out- Anti-slip handle with finger recesses
550.1238 Headlight Head Lamp- The head lamp for business and leisure- Very good wear comfort and secure hold in movement by adjustable front and head band- Lamp can be additionally tilted in click stops- Extra bright with huge range of up to 200 meters- Shock-proof aluminium housing / Protected from rain and water splashes- Zoom from spot to flood light directly on the lamp head- Multifunctional-button with 4 modes: On/Off / 5W / 3W (sleep mode) / Blink- Supplied with batteries
Latest lighting technology with giant luminosity - Peak performance with only a single, low-power Cree LED- These new LEDs are about 150 times brighter than conventional LEDs.- The high-quality quartz glass lens provides clear, bright white light and boasts an extremely uniform illumination.- Selected and durable materials ensure long-term use, both in work and leisure time.- Due to their reliability and up to 20 times higher light density, these high-power LEDs are currently already used in traffic lights or lighting in cars, buses or trains
Light Engineering All Purpose Lamps!
550.1023 Telescopic Magnetic Pick-Up Tool- Small and handy service tool in pen size- Telescopic magnetic pick-up tool with flexible head and cleaning needle for windscreen washer nozzles, in one tool- High quality chrome design with pocket clipTechnical data:Head-Ø: 11 mmLength min: 150 mmLength max: 590 mmMagnetic force: 2.5kgWeight: 60g
max. 2,5kg
Extra luminous power light
Technical data:Lamp: Cree Q5 LEDPower output: 3 WattLight flux: 130 LumenLight range 50mLED lifetime: up to 100 000hSize: L 159mm x head Ø35mmBattery: 3 x AAAWeight: 135g
Technical data:Lamp: Cree LEDPower output: 5 WattLight flux: 300 LumenLight range 200mLED lifetime: up to 100 000hLamp dimensions: L 72mm x W 59mm x H 40mmHead-Ø: 28mmBattery: 3 x AAAWeight: 77g
Lens
Reflector
Carrier
Receptacle + phosphor
Your Local Distributor