Follow these step-by-step instructions to install your ... Installation... · the grass blades...
1
5 6 Once you have covered the complete area, simply nail all of the perimeters down at 500mm intervals using 150mm flat head nails. This must also be applied to the joining seams. Once you have covered the complete area, simply nail all of the perimeters down at 500mm intervals using 150mm flat head nails. This must also be applied to the joining seams. Attention! • Do not attempt to lift the grass by yourself. It is advised that the rolls be cut into manageable lengths before shifting. • Always run grass in one direction. • Ask for our formulae sheet for help to work out required amount of “eco-fill”. • Caution: This product may become warm in direct sunlight. Please check the surface temperature before walking on it with bare feet. * The installation information has been supplied as a reference guide only. No representations or warranties are made regarding the installation information. Top dress the grass with an even sprinkling of fine, dry “eco-fill” silica sand to a thickness of 15-20mm. A broom can be used at this stage to sweep in the sand evenly and to also brush the grass blades straight and vertical. Installation Guide 1 3 2 4 80mm 60mm 15-20mm Follow these step-by-step instructions to install your Newturf! Using a rope or hose, layout the proposed area. Excavate the area to a depth of 80mm. Sprinklers may be capped or removed at this stage. Lay your Newturf lawn grass, making sure you start from one edge and roll out. Cut the over- hanging quantities with a sharp Stanley knife. Remove the ‘salvage’, black strip, from both sides of the grass. This cannot be used to join the grass. Lay 80mm of crushed rock/roadbase and compact with vibrating plate. The level of crushed rock/roadbase, when compacted, should be 15-20mm below “finished height” of surrounding edging/paving. When joining rolls of grass together, be sure to use the Newturf Joining Tape along the seams. Using a 3mm tooth tiling trowel, apply Newturf Exterior Grade Glue evenly along Joining Tape as you go. * Illustrations not to scale
Transcript of Follow these step-by-step instructions to install your ... Installation... · the grass blades...
Newturf Solutions
Head OfficeUnit 2, 347 Bay Road, Cheltenham VIC 3192Phone: 1300 JUST GRASS (1300 587 847)[email protected]
www.newturf.com.au
Cut your water usage…not your grass!
N E W T U R F G R A S S H O U S E
www.newturf.com.au
Distributed by
5 6
80mm
60mm
15-20mm
Once you have covered the complete area, simply nail all of the perimeters down at 500mm intervals using 150mm flat head nails. This must also be applied to the joining seams.
Once you have covered the complete area, simply nail all of the perimeters down at 500mm intervals using 150mm flat head nails. This must also be applied to the joining seams.
Attention!• Donotattempttoliftthegrassbyyourself.Itisadvisedthattherollsbecutintomanageablelengthsbeforeshifting.
• Alwaysrungrassinonedirection.
• Askforourformulaesheetforhelptoworkoutrequiredamountof“eco-fill”.
• Caution:Thisproductmaybecomewarmindirectsunlight.Pleasecheckthesurfacetemperaturebeforewalkingonitwithbarefeet.
* The installation information has been supplied as a reference guide only. No representations or warranties are made regarding the installation information.
Topdressthegrasswithanevensprinklingoffine,dry“eco-fill”silicasandtoathicknessof15-20mm.Abroomcanbeusedatthisstageto sweep in the sand evenly and to also brush the grass blades straight and vertical.
Installation Guide
1
3
2
4
80mm
60mm
15-20mm
80mm
60mm
15-20mm
Follow these step-by-step instructions to install your Newturf!
Using a rope or hose, layout the proposed area. Excavate the area to a depth of 80mm. Sprinklersmaybecappedorremovedat this stage.
LayyourNewturflawngrass,makingsureyoustartfromoneedgeandrollout.Cuttheover-hangingquantitieswithasharpStanleyknife. Removethe‘salvage’,blackstrip,frombothsidesof the grass. This cannot be used to join the grass.
Lay80mmofcrushedrock/roadbaseandcompact with vibrating plate. The level of crushedrock/roadbase,whencompacted,shouldbe15-20mmbelow“finishedheight”ofsurroundingedging/paving.
When joining rolls of grass together, be sure to use the Newturf Joining Tape along the seams. Using a 3mm tooth tiling trowel, apply Newturf Exterior Grade Glue evenly along Joining Tape as you go.
* Illustrations not to scale
![MaterialsandDesign Enhancingmode-Iandmode … · 2020. 12. 3. · the standard ISO: 14125:1998 [29]. The sample dimension was 80mm×20mm×5.5mm.Thetestswereconductedatroomtem- ...](https://static.fdocuments.us/doc/165x107/60c607b1eb112d05ba342932/materialsanddesign-enhancingmode-iandmode-2020-12-3-the-standard-iso-141251998.jpg)
