FIRETHERM INTUMESCENT AND INSULATION SUPPLIES LIMITED

SDS No. 361-02

SAFETY DATA SHEET In accordance w i t h REACH Regulat ion (EC) 1 9 0 7 / 2 0 0 6

P R O D U C T NAME IntUStrap Page 1 of 2 I s s u e Date : 30/08/2013

1. Identif ication of P r o d u c t and Manufacturer

Product: Intustrap. Graphite impregnated EPDM polymer sheet. Used for fire protection within the construction industry

Company: Firetherm, Unit F, Acorn Industrial Park, Crayford Road, Crayford Kent DA1 4FT, England. Tel: | Email: technical@firetherm.com

2. H a z a r d s Identif ication

Prime Hazards: Not classified as dangerous under European Regulation EC No 1272/2008 on classification, labeling & packaging of substance and mixtures.

Eye Contact: May cause irritation

Skin contact: Prolonged contact may cause irritation

Inhalation: Exposure to fume and or dust at high temperatures may cause Irritation of nose, throat and respiratory tract

Ingestion: Swallowing may have the following effects - gastrointestinal irritation

Explosion hazards: None Fire hazards: None Corrosion hazards: None

3. C o m p o s i t i o n : H a z a r d o u s Ingredients

Graphite impregnated EPDM rubber sheet

4. F i rs t A id M e a s u r e s

In case of eye contact, irrigate for 5 minutes and if symptoms persist, seek medical advice

Skin contact: Wash off with soap and plenty of water. If symptoms persist, obtain medical advise.

Inhalation: Move to fresh air in case of accidental inhalation of dust or fumes or both. Consult a physician after significant exposure.

Ingestion: In case of ingestion, do not induce vomiting because of the risk of fluid entering the lungs. Wash out mouth and give plenty of water to drink. Seek medical attention if symptoms persist.

5. F i re F ight ing m e a s u r e s

Extinguishing Media: Use water spray, foam, dry chemical. Keep packaging and surroundings cool with water spray.

Special Precautions: As supplied, product presents no explosion hazard. The products, when burning, may produce dense and toxic fumes with large volume of carbon..

Protective Equipment for Firefighting: Wear self-contained breathing apparatus, rubber boots and heavy rubber gloves

6. A c c i d e n t a l R e l e a s e M e a s u r e s

Personal protection: Minimise contact with skin and eyes. Wear gloves

Environmental Precautions: Dispose of in accordance with local regulations.

Spillages: Collect spilled material in a bag for disposal as non-hazardous waste in accordance with local regulations. Disposal of off-cuts & waste product (EC waste code): 17 06 04

7. Handl ing and S t o r a g e

Handling: Avoid contact with skin and eyes. Wash hands thoroughly after handling.

Storage: Store for short periods on worksite internally, in unopened containers between 5 0 C and 40 o C clear of the ground.

8. P e r s o n a l Protect ion & E x p o s u r e C o n t r o l s

Rubber gloves and safety glasses are recommended.

RYD00092660 0001 RYD00092660/1

FIRETHERM INTUMESCENT AND INSULATION SUPPLIES LIMITED

SDS No. 361-02

SAFETY DATA SHEET In accordance w i t h REACH Regulat ion (EC) 1907 /2006

P R O D U C T NAME IntUStrap Page 2 of 2 I s s u e Date : 30/08/2013

9. P h y s i c a l Data

Appearance: Solid EPDM sheet Odour: Slight typical rubber product odour

Colour: Black sheet Melting point: N/A

Relative Density: 1.26 gm/cu.cm Flash point: N/A

Boiling point: N/A Decomposition Temperature: 200 o C +

Solubility: Insoluble VOC: 0 Grams/litre

10. Stabi l i ty & React iv i ty Data

Reactivity: As supplied the product is inert

Stability: Stable under recommended storage and handling conditions (see section 7). Extensive heating above 200 oC can result in decomposition to carbon monoxide, carbon dioxide, oxides of nitrogen and over 80 times volume expansion of carbon.

Incompatibility: Avoid strong oxidizers.

Shelf life indefinite stored clear of the ground internally

11. T o x i c o l o g i c a l information

Acute toxicity: No data available

Local Effects: May cause skin irritation in susceptible people.

12. E c o l o g i c a l Information

Ecotoxicity: Not expected to be dangerous to the environment

Persistence and degradability: Not readily biodegradable

Bioaccumulative potential: Not relevant

Mobility in soil: Negligible

13. W a s t e D i s p o s a l

Dispose of waste product as general waste at an approved waste site suitable for building waste, observing local regulations.

Contaminated packaging: Dispose In accordance with local regulations

14. T r a n s p o r t Information

No regulations apply for the transport of this product.

ARD/RD-Class: Not dangerous goods IMDG-Class: Not dangerous goods lATA-Class: Not dangerous goods

15. Regu la tory Information

The information contained in this safety data sheet does not constitute the users own assessment of workplace risks as required by other safety legislation. Compiled according to European Regulation EC No 1272/2008 on classification, labeling and packaging of substance and mixtures.

16. Other Information

To be used as a fire stop device as recommended by product data sheets.

To be reviewed: July 2018

Firetherm Intumescent & Insulation Supplies Limited, Unit F, Acorn Industrial Park, Crayford Road, Crayford, Kent. DAI 4FT.

Tel: • • Fax: H H . Website: www.firetherm.com

RYD00092660 0002 RYD00092660/2

FIRETHERM INTUMESCENT AND INSULATION SUPPLIES LIMITED

SDS No. 364-02

SAFETY DATA SHEET In accordance w i t h REACH Regulat ion (EC) 1 9 0 7 / 2 0 0 6

P R O D U C T NAME IntUCOmpOUnd Page 1 of 2 I s s u e Date : 14/01/2014

1. Identif ication of P r o d u c t and Manufacturer

Product: Intucompound. Type of Product: Solid/powder

Company: Firetherm, Unit F, Acorn Industrial Park, Crayford Road, Crayford Kent DA1 4FT, England. Tel: | Email: technical@firetherm.com

2. H a z a r d s Identif ication

Mixture contains naturally occurring minerals and no asbestos present. The product is not classified as hazardous to Regulation (EC) No 1272/2008 on CPL on substance & mixtures.

The powder when mixed with water hardens to solid and the product is not combustible or explosive. A single or short term exposure to dust or wet product presents little or no hazard.

Eye Contact: May cause irritation. Immediate first aid and medical attention required as section 4 Skin Contact: Direct, prolonged or repeated contact may cause discomfort and irritation and attention required as section 4 Inhalation: May cause nose, throat and lung irritation and first aid required as section 4 Ingestion: May cause intestinal distress.

3. C o m p o s i t i o n : H a z a r d o u s Ingredients

Components CAS No

Calcium sulphate dihydrate 26499-65-0

4. F i rs t A id M e a s u r e s

Content %

55-100

Classification

none

Eye contact: Flush with copious quantities of fresh water-seek medical attention without delay. Skin contact: Wash immediately with soap and water. If skin irritation persists seek medical attention. Inhalation: May cause irritation. Remove patient to fresh air. If symptoms persist, seek medical attention. Ingestion: Ingestion of small quantities is unlikely to cause significant reaction. Do not induce vomiting because of the risk of fluid entering the lungs. Wash out mouth and give plenty of water to drink

5. F i re F ight ing m e a s u r e s

In case of fire, use extinguishing media appropriate for surrounding area.

6. A c c i d e n t a l R e l e a s e M e a s u r e s

Personal protection: Minimise contact with skin and eyes. Wear gloves If dry, dispose of as non hazardous waste. If wet, adsorb with sand, earth or non-flammable absorbent material and dispose of after curing as non hazardous waste.

7. Handl ing and S t o r a g e

Do not eat or drink during use. Observe good industrial hygiene. Store indoors in unopened bags between 5 - 40 c, above ground. Shelf life 12 months

8. P e r s o n a l Protect ion & E x p o s u r e C o n t r o l s

Workplace Exposure Limit - LTEL: 10 mg/M3 (Inh), 4 mg/M3 (Resp). 8 hr TWA. (Inh = Inhalable Dust. Resp = Respirable dust) Respiratory: The use of a dust mask or equivalent to EN149 Category FFP2S, and the provision of dust extraction/ventilation where dust is produced is recommended. Use in well-ventilated areas

Hands: Gloves Biological Exposure Limited:

Eyes: Goggles Not applicable.

Skin: General protective overalls.

RYD00092660 0003 RYD00092660/3

P R O D U C T NAME Intucompound Page 2 of 2 I ssue Date : 14/01/2014

9. Physical Data

Physical state: Odour: Bulk Density: Water solubility: Autoignition temp: Explosion properties:

7 grams/Litre Not applicable Not applicable

None 667kg/m3

Powder Colour: Off white pH: 5 - 8 VOC : 0 grams/Litre Flashpoint: Not relevant Decomposition Temp: >1200c

10. Stability & Reactivity Data

Stable product, which does not cause any dangerous reactions with other substances. Product is designed to harden when mixed with water.

Hazardous decomposition products: None in normal conditions. Over 1200 C, the product can be decomposed into sulphur trioxide & CaO (quicklime).

Reactivity Data Stable in dry environment. Product in water becomes mildly alkaline and therefore, barrier tape is recommended to avoid direct contact with metal, aluminum, copper, services. Referto Product Data Sheet. Contact with strong acids must be avoided.

11. Toxicological information

Acute toxicity: Not toxic Ingestion: Not toxic Inhalation/Skin/Eye: May cause eyes, skin, throat, lungs irritation for sensitive persons.

12. Ecological Information

Do not allow to enter drains because of danger of blockage. This product is based on natural gypsum and presents no ecological hazard to the environment. Ecotoxicological study available in public domain showed no toxic effect. Gypsum is naturally occurring mineral and therefore biodegradation and bioaccumulation potential is not applicable. Less than 10 grams/Litre of Intucompound in powdered form can soluble in water and in the event, presence of organic material and in certain anaerobic conditions, sulfate can conduct to the formation of hydrogen sulphide. Sulfate ion is one of the less toxic anion (guidelines for drinkable water, WHO 1993).

13. Waste Disposal

Dispose of at an approved waste site suitable for building waste, observing local regulations. Contaminated packaging: Dispose In accordance with local regulations

14. Transport Information

Not registered as a dangerous material for transport. UN Number - Not applicable IMDG - Not dangerous goods IATA - Not dangerous goods ADR/RID - Not dangerous goods Packaging group:- Not applicable

15. Regulatory Information

EEC Regulatory information: Preparation/mixture not considered as dangerous according to 67/548/CEE and 99/45/CEE regulations. EU Directives: Dangerous Preparation Directive 1999/45/EC

16. Other Information

EEC Regulatory information: preparation not considered as dangerous according to 67/548/CEE and 99/45/CEE regulations. Regulation (EC) No 1272/2008 on Classification, Labelling and Packaging of substances and mixtures.

To be reviewed: December 2018

Firetherm Intumescent & Insulation Supplies Limited, Unit F, Acorn Industrial Park, Crayford Road, Crayford, Kent. DAI 4FT.

Dangerous reactions: None Dangerous properties: None

Tel: Fax: Website: www.firetherm.com

RYD00092660 0004 RYD00092660/4

Firethetm

Quality Assured

UK Manufactured

Fire Protection

\ Firetherm Intumescent & Insulation Supplies Limited

Data S h e e t N u m b e r U K - B S - E N 361-01 Issued 0 1 - 2 0 1 4 rev iew da te 01-2015

Product Data Sheet - Intustrap Application

Firetherm Intustrap is a high pressure graphite manipulated Intumescent expansion device designed to close off combustible elements whilst maintaining compartmentation. Firetherm Intustrap is also a component product incorporated within many Firetherm Products.

Description

Firetherm Intustrap is a Ruberoid strip with high flexibility and is most commonly used around all types of pipe Insulation up to SOmm thick or combustible pipes with a diameter of between 20mm and 1 SOmm.

Firetherm Intustrap may also be used around Conduits, Cables (if required), and to close ventilated air spaces. Intustrap can also be moulded by hand and used as a putty within small openings.

Specifications

Available Sizes.

60mm x 4mm x 25m Rolls

60mm x 4mm x 600mm Strips,

Installation Basic requirements

All Insulation types : 2 layers 60 x 4 mm as per requirement, (maximum insulation thickness 50mm)

Combustible Pipes : 55mm 1 layer, 82mm 2 layers, 110mm 3 layers, 160mm 4 layers

Fire Testing

Tested at Chiltern International Fire to BS-EN 1366 pt 3 & BS476 pt 22.

Third Party Accredited by Exova Warrington: Certificate Number CF583.

Tested at Exova Warrington Fire to BS 476 pt 22.

Typical Benefits

Unaffected by Moisture.

Fully Tested for up to 240 minutes integrity and insulation, (dependant on application)

Available in easy to handle rolls.

Simply link with duct tape.

Typical Configuration Types.

Combustible pipes. Insulations types, Rockfibre, Glass fibre , Phenolic, Nitrile Rubbers.

Tested In Floors and Walls including Lightweight Partitions*.

May also be used within Firetherm Intubatt 1 & 2, Please consult literature or technical department.

Fire Resistance Testing

* Consult Technical Department for methodology

• • U M I M

Firetherm Intumescent & Insulation Supplies Limited

Unit F Acorn Industrial Park

Crayford Road

Crayford

Kent

DAI 4FT

Phone: •

Email: sales@firetherm.com

Web: www.f i retherm.com

REF: CF 583

certifire

RYD00092660 0005 RYD00092660/5

^retftem? Quality Assured

UK Manufactured

Fire Protection

\ Firetherm Intumescent & Insulation Supplies Limited

Data S h e e t N u m b e r U K - B S - E N 361-01 Issued 0 1 - 2 0 1 4 rev iew date 01-2015

Intustrap

Tested substrates to contain expansion:

1 / 64kg Rock Mineral Fibre 0-60mm Annular Space (SOmm Min imum Depth)

2 / Intumastic wi thin Concrete 0- 20mm Annular Space

3/ Intubatt 2 140kg/m3 (Walls) - Intudeck 140kg/m3 (Floors- Timber)

4 / Intubatt 1180kg/m3

5/ Intucompound 1000kg/m3

6/ Concrete-Block-work

7/ 0.7 gauge (minimum) steel.

Pipe composites Tested Range given as fol lows:

Evidence taken From BS-EN 1366-3 : CIF Doc 11:1004 :ASFP Guidance:

Tested Pipes : HOPE, ABS, MDPE, PVC-U,PVC-C, C-PVC, PPR, PP, PE

Currently any other pipe composites would require additional testing.

Intustrap Layers:

1 layer 60 x 4mm Intustrap

2 layers 60 x 4mm Intustrap

3 layers 60 x 4mm Intustrap

4 layers 60 x 4mm Intustrap*

2 layers 60 x 4mm Intustrap

Pipes: 0-55mm:

Pipes: 55-82mm:

Pipes: 82-125mm:

Pipes 125-160mm:

Insulation all types:

Evidence taken From BS-EN 1366-3 Testing: CIF Doc Tl:1004 :

* = not for use within Intubatt Vertically at this size

Firetherm recommend that all fire stopping products should be installed by a third party accredited fire stopping contractor. Full application details and methodology instructions should be requested before installation of this product commences .Suitability of this product should be ensured before installation. Standard terms and conditions apply at all times.

Fire Resistance Testing

• • U M E I I

i IRMiLHni kiJi^ I N I

Firetherm Intumescent & Insulation Supplies Limited

Unit F Acorn Industrial Park

Crayford Road

Crayford

Kent

DAI 4FT

Phone: •

^ ^ ^ ^ ^ ^ ^ ^ ^ Email: sales@firetherm.com

Web: www.f i re therm.com

REF: CF 583

certifire

RYD00092660 0006 RYD00092660/6

Firethetm \ Firetherm Intumescent & Insulation Supplies Limited

Data S h e e t N u m b e r U K - B S - E N 7 0 0 4

Quality Assured

Fire Protection Product Data Sheet - Intucompound Application

Firetherm Intucompound is used to provide both an excellent Fire Barrier and a physically strong barrier in floors where personnel may occasionally be required. Intucompound may also be used within walls and in situations where the restraint of Dampers or Ducting is not possible using conventional methods. Firetherm Intucompound is recommended for use in dry internal conditions, though can be separately waterproofed at full cure.

Description

Firetherm Intucompound is a dry powder mix formed of Inorganic binders, lightweight aggregates and stable additives. The product does not contain fibres or asbestos and is halogen free. After mixing the product expands to link into surrounding substrates and ensure an excellent seal around sen/ice penetrants. Intucompound achieves full cure in 40 days however has been tested to be load capable after 50 hours. Intucompound Air Cures and should not be covered during it curing process.

Specifications

20 kg bag:

Mix Rate 2:1 or 3:1 (with water)

3.5 bags per m2 at 100mm depth

Fire Testing

Tested at Chiltern International Fire to BS/EN 1366-3 : 240 minutes

Tested at Exova Warrington Fire to BS476 Pt 22 : 240 minutes

Third Party Accredited By Exova Warrington Fire Certificate Number CF579

Typical Installation

Maximum wall opening without support 900 x 600mm or 0.54 m2

Maximum floor opening without support 900 x 600mm or 0.54 m2

Maximum Continuous Span without support 300mm x infinite length

Maximum Continuous Span with Support 2000mm x infinite length

Larger Spans can be achieved underthe guidance of a structural engineer, (A chargeable service)

Acoustic Capability up to 52db.

Typical Depth of fill = 100mm 75mm and 50mm variations are not load capable and will have a reduced fire performance .

Typical Service Types.

Static Joint Seals: Floor Seals : Wall Seals : Load Capable Seals

May a l s o be u s e d for fire s e a l i n g a r o u n d :

Cables, Steel Pipes, Copper Pipes, Cable Trays, Combustible Pipes, Dampers & Ducting

A soft joint should be used around any pipe that is likely to fracture due to thermal expansion.

Firetherm Intumescent & Insulation Supplies Limited

Unit F Acorn Industrial Park

Crayford Road

Crayford

Kent

DAI 4FT

Phone: •

Email: sales@firetherm.com

Web: www.f i retherm.com

REF: CF 579

certifire

RYD00092660 0007 RYD00092660/7