Final Infographic for Web Upload-V2
-
Upload
tenzin-phenz -
Category
Documents
-
view
220 -
download
0
Transcript of Final Infographic for Web Upload-V2
-
8/10/2019 Final Infographic for Web Upload-V2
1/1
25
38 167
743Heating
nd Cooling
Water Heating
overage of BCAnergy EfficiencyRequirements
OtherAppliances
Lighting
Refrigeration
CookingStandby
Totalmin.
R-Value
0
1
2
3
4
5
65.1
2.7 2.8
1.4
Roof &Ceiling
Externalwalls
[4]
26
133
63
How Have Housing Energy Efficiency Requirements Made A Difference?
2003
ergy efficiency requirements for new housing were first introduced into the Building Code of Australia (BCA) Housing Provisions in03. The objective was to reduce energy use and hence greenhouse gas emissions. Since then, Australians have been able to enjoy
ectricity and gas savings by living in energy efficient homes with reduced consumption of operational lighting, heating and coolingergy.
Location: Adelaide, South AustraliaClimate Zone: 5
2013
sclaimer: While the ABCB has made every effort to ensure that the material in this document is accurate and up to date, such material does in no way constitute the provision of professional advice.The ABCB gives no warranty or guarantee and accepts no legal liability whatsoever arising from or connected to the accuracy, reliability,rrency or completeness of any material contained herein. Users should seek appropriate independent professional advice prior to relying on, or entering into any commitment based on material within this document in relation to building or related activities. Its interpretation in no way overrides the approvals processes in any jurisidiction.
The two hypothetical residential properties illustrated above - a 2003 house and a 2013 house - depict the evolution of a typical Australianhome. The changes reflect the implementation of stronger minimum energy efficiency requirements in the Building Code of Australia (BCA) ,increasing from a 3 to 6 star energy rating.Note: Values stated below are indicative only.
NatHERSRating
Energy ConsumptionkWh/ m per annum
Generally, the higher the R-valuethe better the thermal performance.
Fluorescent light bulbs use about 25%
of the energy of traditional light bulbs.
Depending on the climate you live in,
solar hot water systems can provide
between 50% to 90% of your hot water
for free just by using the suns energy.
Thermal Performance
Artificial Lighting
Selection of the appropriate glazingand permanent shading devices foryour climate zone is a key element of
passive design.
Save up to 45% on heating and
cooling energy with a well
insulated roof and ceiling, and
an additional 20% with wall
insulation.*
Shading can block up to 90% of
heat gained from direct sunlight.*
Appropriate shading of glass and
openings reduce unwanted heat
gain in summer, improves
comfort, and saves on building
cooling costs.
How do we use energy?
Glazing & Shading
2003
2013
Single clear glass,aluminium framing
Typical Constr uction:
Double glazed clear glass,aluminium framing
2003
2013
2003-2013, A ComparisonWhats in a Star?
Heated Water SystemInsulation
The use of efficient lighting solutions wasrequired with the introduction of the lightingprovisions in 2010.
Higher performance glazing requiredfor larger glazed areas and in certainorientations.
Windows
[1]
Electric energy
TraditionalIncandescent
CFL or LED
Energyefficientlighting solutions
2003(no BCA requirements)
2013
2003(no BCA requirements)
2013
] Approximate values calculated from NatHERS star criteria] Source: YourHome (4th edition, 2010), Baseline Energy Estimates] The BCA is part of the National Construction Code Series] Total R-Value includes added insulation and building construction (m.K/w)
Source: YourHome (4th edition, 2010)
Renewable or lowGHG intensity energy
[3]
[2]
Roof lights
http://www.abcb.gov.au/