Fab Tolerance

download Fab Tolerance

of 2

Transcript of Fab Tolerance

  • 8/12/2019 Fab Tolerance

    1/2

    ** Given underneath is a gist of the FABRICATION TOLERANCE rules taken from

    AI R !A and AI !B CO"E#$ This is for %ui&k referen&e onl'$ lease refer the a&tual

    rule for the &om(lete (i&ture$

    FABRICATION TOLERANCE# ) AIR!A +"e&em,er !---.

    #e&$ //$/$0 B ) 1a&ket and "e&k se&tion &olumns

    - In any plane, field assembly tolerance at Top of Jacket & bottom of deck column, for

    CL (central line) of column to CL of adjacent column : - !" mm

    - #t all deck le$els, CL to CL of t%o columns : - ! mm

    - In ot'er jacket planes : - ! mm

    - ia*onals of a rectan*ular plan layout + ! mm

    - trai*'tness of jacket columns + !" mm, but, not . mm in any m len*t'

    - Top of all jacket column /le$ation : - ! mm

    - Locations of ends of 'ea$y %alled 0 jacket cans or deck le* joint cans : - 12 mm

    - C'an*e in locations due to c'an*e in %all t'ickness in jacket le*s or deck columns : +

    2! mm

    //$/$0$C ) 1a&ket and "e&k Ere&tion Bra&ing

    - all braces in a 'ori3ontal plane s'ould be 'eld $ertically %it'in ! mm

    - location c'an*es due to %all t'ickness c'an*e in brace : - 12 mm

    - all bracin*s (end point dimensioned) : - ! mm of planned dimension

    //$/$0$" ) "e&k Beams

    - on central line of deck beam, bet%een ends : - ! mm

    - at no point on C4L, beam %ill be out of line more t'an ! mm 'ori3ontally or ! mm

    $ertically

    //$/$0$F ) Grating : joint in *ratin* at point of support only4

    //$/$0$G ) Fen&ing 2 3and rails : top of rail %ill be strai*'t and le$el to t'e eye

    //$/$0$3 ) Landing 2 #tairs

    - location, 'ori3ontally : %it'in 56 mm

    //$/$0$/ iles

    - minimum 7ile piece len*t' : ! m or one pipe diameter, %'ic' e$er is less

    - lon* seam of t%o adjacent piles : min " de*ree apart (89C need : !;" de*ree)

    - ma )

    - C'eck strai*'tness by taut %ire, at minimum radius points

    - ?oot face of be$els : not out of s@uare 2 mm per ! m, ma

  • 8/12/2019 Fab Tolerance

    2/2

    5$/$5 B ) 1a&ket orientationde$iation after installation : 2 de*ree in eit'er direction

    TOLERANCE# A# ER AI 6 !B +1anuar' !--!. )

    0$7 - ?adial offset of a,utting edgesof lon* %eld seam - not more t'an ! >; inc'

    - lon*itudinal %eld seam of adjacent cans : " de*ree apart

    0$0 Girth 8eld

    - ?adial offset of abuttin* ed*es of *irt' seam 0 not *reater t'an "41 = %all t'ickness,

    but ! >B inc' ma ; inc' ma t + ! : ; ratio

    - for diameter . B; inc', ma!6 inc' : need not be remo$ed- ?epair of defects, deeper t'an 1" D of FtG or len*t' > %idt' . 1" D nominal

    diameter : not permitted in fabrication4